Search Products

This DOT kit includes LED headlight assembly with plug-and-play wiring harness, a specially designed adjustable steel mounting bracket, and all the required installation hardware.

No cutting, no drilling, no wiring modifications! Installation takes 5 minutes.

This kit is highly recommend over the non-DOT kit. The low beam has extra punch and a proper beam pattern cut-off. The high beam throws light far and wide. It’s already a crowd favorite!

Two colors to choose from, Chrome or Black. Light output and beam pattern are the same for either color.

• Low Beam: 20W, 2,800 Lumens
• High Beam: 35W, 3,600 Lumens
• Color Temperature: 6,000k
• DOT & SAE Compliant
• CE, RoHS, ISO9002, IP67

Want an amazing increase in throttle response? More power over a much wider range? The Mikuni TM40 does all of that plus runs smoother at lower RPMs and pulls taller gearing with ease.

Our complete kit comes with alloy adapter rings bonded to the genuine TM40 carburetor body for a firm reliable fit in the stock air boots. We also include new low friction cables, an extended fuel screw, complete instructions along with a wide range of extra jetting for fine tuning. It even has a vacuum port for the stock fuel petcock.

The carburetor comes pre-jetted for the typical mods: performance pipe and modified air box, or we can set it up for your particular bike before we ship it out.

 Instead of the tough to reach choke knob, all TM40's come with a remote choke and bracket. This makes it easier to reach the knob, especially if you have an oversize tank.

From Shinko Tires, the 705 Series are DOT approved Dual Sport tires designed for 75% street and 25% trail riding. An versatile tread pattern provides excellent wet and dry weather adhesion and the compound resists tearing while riding off-road. "R" in size denotes a radial tire.

This is one of the few plastic parts on the DR650 that can ruin your day if it breaks or fails on you. This gear helps drive the oil pump to circulate oil throughout your entire motor, without it, your motor will fail entirely. The idler gear is not known for being a common failure point in the DR650 motor but, it has failed riders in the past. Usually in the form of a broken gear or stripped teeth. Upon inspection, look for any kind of crack, chipped or missing teeth on the gear. It is not a complicated repair to swap an old gear for a new one, as the best time to replace it is when you've opened up the clutch side case cover for another repair i.e., (NSU screws or clutch hub bushing replacements). This is an O.E. Suzuki part.

Wider foot pegs for sure-footed comfort. Cast stainless steel.

• Formulated to work in combination with the cotton fabric in K&N Air Filter elements to provide a superior air filtration system
• Quickly penetrates the filter pleats; remains suspended in the filter pleats
• 8 U.S. FL OZ. / 237 ML
• Made in the U.S.A.

High Quality chain. Will need to be cut to fit your sprocket combination.

Steel braided lines have a Teflon tube as a core wrapped with a stainless steel wire braided exterior which doesn't allow the brake lines to stretch under pressure like stock rubber lines do.

The benefit is a firmer brake lever with better feel because the energy that was going into stretching the stock lines now goes straight to the brakes.

Ditch the stock ugly plastic sub-fender and install a B&B Off Road Engineering License Plate Holder. Comes with an LED light to keep the license plate lit up.

The 244 Series Dual Sport street and trail tires were designed to be equally at home on dirt or pavement. Great value.

• DOT approved, tube type
• 4-ply rating
• All sizes designed for front or rear fitment

Heavy duty shock bumper. The stock bumper is prone to disintegrating with age. If you are re-valving your shock it's a good idea to be sure the bumper is in good shape.

Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm. Lo-pegs are down and back 1/4".

Made from precision-drawn, chrome-vanadium tool steel, the BikeMaster® 9-Piece Ball End Hex Wrench Set and Holder features a bead-blasted surface for a better grip and a corrosion-resistant coating. They have a ball end, allowing an angled reach and access to obscured bolts. It comes with a durable holder and manufacturer's lifetime warranty.

Comes with sizes 1.5mm, 2mm, 2.5mm, 3mm, 4mm, 5mm, 6mm, 8mm and 10mm

Our logo on a 20oz double wall 18/8 stainless steel thermal tumbler with copper vacuum insulation, threaded snap-fit lid, and powder coated finish.

The copper plating on the inner wall is an extra defense against temperature transfer. Heat escapes much slower so your hot coffee stays hot even in a snow storm, and heat enters much slower so your ice water doesn't melt even under a blistering summer sun.

We have tested this bottle with 160° water placed on it's side for 7 hours mimicking being in a saddle bag with coffee from the morning campsite. The bottle did not leak when the lid was properly secured and the water only dropped to 113° at the end of our test.

Pair it with the OBR bottle wrap for even better value and have a holder on your luggage for your new bottle for ease of access and security.

Keep essentials close at hand with this useful piece of water repellent motorcycle luggage. This tank bag is rugged, reliable, and ready to go!

• Fits most sloped tanks
• The 4 point harness makes it easy to attach to your tank
• Easy to find yellow cord on main opening zipper sliders
• Designed in the USA and made with Wolfman legendary care and quality

The 2020 Blackhawk Motorcycle Tank Bag WP (Welded Product) is their largest tank bag, now manufactured using the latest in Radio Frequency (RF Welding) technology. The water repellent Blackhawk is ready for the long haul. Contoured to fit most sloped tanks. The Blackhawk utilizes the same 4-point harness used on the 2020 Enduro Tank bag, making switching out bags a snap.

Other Features:

• Custom 840d Nylon TPU laminate, black outside bright yellow (Wolfman Colors) inside
• Removable clear pocket (Not for phone use as smartphones can overheat in direct sunlight)
• Removable waist belt pouch

Dimensions:

• Length: 11.25" /28.5cm
• Width: 8.5" /21.5cm
• Height: Front-7" /18cm-Rear- 4.75" /12cm
• Clear Pocket: 9.75”/24.7cm long X 4.75”/12cm wide

Bolt-on side case armor from Warp 9 Racing.

Made of High Density Polyethylene, the same very tough stuff they make their frame and axle sliders out of.

3mm thick complete side case coverage

6.5mm thick in the leading and bottom edges where impacts typically happen

Covers the oil filter which takes a lot of impacts on these bikes

Includes new longer case bolts to hold on the case guards

Extremely light handling with exceptional grip in corners, combined with high mileage compound. This radial tire offers great control and feedback when riding on the limit. Quick warm-up and good grip when cold thanks to a specially developed tread compound.

0° Steel belt construction on the front and rear for higher stability and great feed-back when braking into and accelerating out of curves.

One of the best street SuperMoto tires.

Tubeless and H rated (max speed of 130 mph)

One folding mirror. Includes handlebar mount. Can be used on left or right side.

Sold individually.

The Warp 9 shift lever is black anodized and the Warp 9 logo is laser etched into the finish. The black anodized knurled aluminum tip is folding and returns via a stainless-steel return spring. Includes the pinch bolt as well.

The tip is replaceable in the event of damage.

Taillight, brakelight, turnsignals, license plate light & license plate mount. Taillight is DOT approved, turn signals are not. Attaches to the underside of MX Style rear fenders. Turnsignals are embedded in the taillight housing. Wiring instructions included.
*Flushmount signals may require resistors to flash correctly

• Kits contain all parts needed to re-seal leaking master cylinders
• Includes cup seals, copper washers, o-rings and spring, and clips where applicable

Make the Edge-2 installation as easy as possible with an Optional Connector Set. This allows you to put an OEM style connector on the Edge Taillight making the connection simple. Stock plug will go right into this unit and off you go. Will need a crimp tool or set of needle nose pliers to crimp connectors on.

• Patented fork seal features a balanced 3 lip design that evenly distributes the pressure reducing operating temperature, wear and friction
• Custom Elastomer Fork Seals have been tested to outlast OEM fork seals. Extends typical seal life by 3 to 5 times over OEM seals
• Stiction (friction) measures from 1/3 to 1/2 less than OEM seals for smoother fork action
• Lower Stiction, Longer Life! It doesn’t get any better than this!
• Plus, the only complete line of dust wipers! Wipers should be replaced with the fork seals to assure peak performance

These footpeg heads are bike model specific and are required to install Puig footpegs to your bike.

• Allow for custom positioning of your new Puig footpegs
• Sturdy construction

Fits Honda CRF450L Motorcycles (Front Turn Signals)

OEM Fit Left Front and Right Front turn signal connectors with wires pre-attached.

This kit is specifically for attaching After-Market turn signals to the front of the CRF250L / Rally or CRF450L.

These are replacement rubber inserts for the Puig Enduro footpegs. Sold as a pair.

High Quality Replacement Wheel Bearings and Seals for your TTR125

Yoshimura has always been synonymous with quality craftsmanship, precision fitment, and impeccable quality. The Fender Eliminator Kits are no exception, and they are sure to give your motorcycle the sleek race look that every rider craves

Features:

• Precision laser-cut stainless steel bracket tucks discreetly under the tail section of the motorcycle
• Black anodized CNC machined light housing with laser-etched Yoshimura logo
• Light housing contains four bright LED lights
• Black anodized aluminum license plate frame with silk screened Yoshimura logo
• Stainless steel hardware included
• Compatible with aftermarket turn signals when combined with Universal turn signal bracket kit (960-9199)

The Pro-Series is an excellent replacement for the stock shock. With both compression and rebound adjustable as well as preload adjustable, you can tailor the performance to match your riding style. Compact and rigid design with piggyback type reservoir specifically engineered for your WR250R. Fully serviceable shock is designed for the long haul.

Select the spring you want installed based on the load you plan to carry. Choose the 'standard' 8.15kg/mm spring for rider/ luggage up to 220lbs. Weigh more than 220 lbs, or are loaded to the max, think about the 10.19kg/mm 'heavy' spring.

Trails End Adventure Motorcycle Tank Bag by Nelson-Rigg, a lot of bag for a little money.

• V-shaped base to accommodate off-road, dual-sport and adventure motorcycles
• New quick release makes for quick mounting and refueling
• Top quality UltraMax™ polyester with maximum UV protection
• Convenient side pockets to hold smaller items for easy access
• Bag maintains shape, has reflective piping and a lined interior
• Reverse coil zippers help keep out dust and dirt, keeping zippers working smoothly
• Adjustable shoulder/tether strap
• Protective base material prevents slipping or marking
• Clear map pocket is touch screen device friendly
• Fully expandable when more room is needed
• Includes our exclusive Lifetime warranty and waterproof rain cover
• Main compartment measures: 12" L x 7" W x 9" H Standard Config. - 12" L x 7" W x 12" H Expanded
• Holds 12.4 Liters / 16.5 Liters expanded

JT Sprockets is the world's leading manufacturer of aftermarket sprockets, constantly raising the industry's standards for quality and service. JT Sprockets are the only sprocket manufacturer using the ultra-durable high carbon C49 steel for rear sprockets.

Works on AC and DC lighting systems

  Not compatible with any DRZ400

Protects the exposed oil line on Honda XR250/400R

Roll-up pouch ideal for tucking away your lights when out on the trail.

Our Tool Tube mounts in place of the little stock tool carrier. The tube is made from 3 1/2" O.D. ABS pipe. It's held by 3 strong powder coated steel straps. Both ends are sealed with waterproof expanding plugs. This is the ideal way to carry those items you always want to have with you on every ride. Tube is approximately 13" long.

You can now order your Tool Tube with a Locking End cap, mini padlock and keys included, on the exposed end.

If you already have a Tool Tube you can order just the Locking End Cap and lock.

These are the brightest LED tail-light bulbs we've seen for Dual-Sport riding.

Tested, these survive off-road riding, and the brightness is amazing, 600 total lumens.

Compact size fits into tightest tail lights, easy to install, and 30,000 hour life.

Matte black 118mm x 85mm mirrors. Similar to stock size.

• 8mm thread

Sold In Pairs

Made with heat-treated carbon steel for longer wear life and reduced galling. Stock size, simple bolt-on procedure.

• Made from strong and lightweight 4mm thick aircraft aluminum
• Protects vital engine parts from rocks and debris
• Custom fit to your specific bike model
• Oil drain hole for easy access
• All mounting hardware included

These hand-built units out of Australia are one of the most advanced radiator protection systems available! CNC machined 6000 series three-dimensional aluminium extrusion melded with 5000 series alloy plate to create a system that protects your precious radiator from almost any direction.

Designed with a fin angle that allows almost nothing to come in contact with the vulnerable core that is otherwise directly exposed to roost, rocks and all sorts of trailside debris. The fins are designed in a fashion that they completely mimic the designed airflow characteristics of the OEM plastic protector fins.

The protective finned louver panel quickly and easily unbolts to make clean-up a snap. Three-piece modular construction allows for greater design flexibility which eliminates the compromises that are built into one-piece designs. If any single piece of this unit is ever damaged, it is replaceable by itself, no need to replace the entire guard. Just give us a call. Installation is a snap, taking no more than 30 minutes with basic tools.

By simply replacing a motorcycle's stock shock linkage with with a longer, stronger and lighter DeVol Lowering Linkage, a bike's seat height will be dramatically lower to help give those riders with shorter inseams a more confident and enjoyable ride.

• High-grade U.S. billet aluminum
• Longer linkage dramatically lowers seat height
• Hard anodized finish
• Improves your bike's front-end stability and handling
• Works at all speeds; you'll instantly notice how the bike's rear end tracks straighter
• Aluminum alloy link lowers bike's rear end 5/8" - 1-1/2" on various models
• Stronger than stock
• Softens rear suspension slightly

Designed to enhance the appearance of your motorcycle, yet provide greater riding distance per tankful. Larger capacity than stock, yet very slim and sleek. Perfect for the dunes or the race track! These tanks are made with crosslinked polyethylene for extra strength and durability.

Natural color is recommended to easily see the fuel level in the tank. Includes cap and fuel petcock.

A Moose Racing headlight guard by will protect the headlight from flying debris

• Fabricated from mild steel and expanded metal
• Powder-coated flat black
• Light weight with limited reduction in light output
• Easy installation with all required hardware provided

Don't like the low fender on your TW200? The ProCycle High Mount Fender Bracket allows you to mount your fender under the lower triple clamp to create more clearance around your front wheel and drastically improve the look of your T-Dub.

The kit is made of high-quality steel components manufactured in the USA, and includes the bracket and all required hardware.

Don't forget to add a new fender for that supermoto look!

LED powered taillight, brake light, license plate light & license plate mount. Attaches to the underside of MX style rear fenders.

Make your life a little easier by having a set of these in your toolbox. Designed to simplify installation and removal of clip-type master links. One tip is shorter and notched to be placed on the pin which allows the longer end to push the clip.

Dielectric Grease is an insulating silicone grease designed to insulate and protect electrical connections. Pack it into the back side of electrical connectors to protect them from moisture and corrosion. Do not put it directly on the connection surfaces.

• Protects electrical connections and wiring from salt, dirt and corrosion.
• Prevents voltage leaks around any electrical connection.
• Extends the life of bulb sockets.
• Suggested Applications: Marine and automotive electrical connections, spark plug boots, trailer hitches, battery terminals.

The Plugfones Guardian Plus is an upgrade from the Guardian with an expanded feature-set and functional changes. A step above the Basic series including enhanced audio, the option for replaceable plugs, extended 4-foot cord length, and a straight 3.5mm jack. The IsoTalk™ noise isolating mic dampens ambient noise in busy environments while enhancing vocal audio to make calls clear and concise.

Audio control is equipped with song ahead, song back, volume up, volume down, answer, hang up, and decline a call. Utilizing feedback from our customers, we have moved the control panel closer to the 3.5mm jack for easy access. The Guardian Plus speakers have been factory tuned for high quality audio and an enjoyable listening experience without losing any important frequencies.

Included with the Guardian are 2 different types of plugs (4 sets total included), the first is a comfortable silicone plug rated at a 27 NRR (noise reduction rating) and the second is our patented foam 3-tier plug that leads the industry with a 29 NRR (noise reduction rating). To protect your plugs, the Guardian series includes a hard case with a removable lid and transport them safely.

The Plugfones Guardian Plus is also offered in the VL configuration (Volume Limiting) which maxes the audio output volume no higher than 85 decibels to comply with OSHA environment safety standards.

The 250 taillight & brake light fits perfectly into the pocket from the stock DR650 taillight on the rear fender. Smaller and much better looking than the original.

Totally 'plug-n-play', includes a standard bulb installed or purchase an LED replacement, sold separate, for even brighter braking. The wire pigtail plugs directly into the DR650 harness just like stock.

  Does not fit with the ProCycle Fender

Replacement OEM swingarm pivot covers. Keep mud and dirt away from the swingarm bolt. Sold as a set of one left side and one right side cover.

Born in the motocross arena and off-road trails. Matured in the MXGP 1 and 2 racing series, Paris-Dakar and national racing series like the GNCC. Fine tuned for racing, adventure touring and off-road riding of any style. SBS delivers unmatched performance and quality. Matching riding styles and motorcycle performance with several different compounds, all made to exceed the highest industry standards. Proudly engineered and made in Denmark.

OFF-ROAD SINTERED BRAKE PADS (SI)
• The right choice for muddy, wet or sandy conditions
• Class-leading friction rating developed in racing under severe conditions
• Formulated for low wear and high performance
• Quiet, powerful and long-lasting

New design gives you more protection and uses OEM mounting points for easy installation.

• Made from 4mm thick aircraft aluminum
• Oil drain hole for easy access
• All mounting hardware included

96 page 5th Edition Sudco Mikuni Carburetor Manual featuring the complete line of Mikuni RM, VM, HSR, HS, TM, TMX and BN Carburetors and Fuel Pumps with Parts Breakdown Diagrams, available Tuning Components, Tuning and Setup information of all Mikuni Carburetors & Fuel Pumps for Dirt, Street and Personal Watercraft applications.

Great resource for the do it your self rider to get the most out your carburetor.

• Seal profile is engineered to create equal pressure in each seal lip; equalized seal pressure creates less drag and longer seal life
• Patented MAX-LIFE has a coefficient of friction up to 3 times less than the OEM seal material
• Triple-lip seal design
• Dyno-tested to last 3 to 4 times longer than OEM seals
• Directional ribs allow seal to be installed easily
• Sold in Pairs

Moose Racing has just released a new set of rackless saddlebags in their ADV1 line up. These saddlebags come with a base panel that allows you to mount the bags in multiple positions to accommodate different side panels designs. These are different than the traditional ADV1 dry roll-up style as there is a shielded zipper, but they are made of the same tarpaulin material, this makes them strongly water resistant and rugged.

• Saddle dimension: 30"L x 13"W
• Bag dimension: 19.3"L x 11"W x 6"H
• Volume: 36L (18L per bag)
• Universal mounting
• Multiple attachment angels for a custom fit
• Water resistant tarpaulin construction
• Molle attachment system for accessories and the addition of the ADV1 Center Rear Bag.
• Vibration absorbing protective pads under the saddle
• Abrasion resistant Hypalon panels for additional durability

Keep your head warm while you're not wearing your helmet on those colder days. Our premium waffle knit beanie is available in black or olive green.

Comes complete with our custom ProCycle embroidered patch.

This is a great tail bag for anyone looking for a mix of a saddle bag & tail bag. If you have a Cycle Racks rear top rack on a TW200, it lays nicely across giving you plenty of storage.

• 1200-denier Technolast water-resistant, UV-treated polyester construction
• Large main compartment and two smaller side pockets (52 Liters in total)
• Unique anchor knot attachment system features anti-slip cam buckles
• Anti-scratch base
• Rain cover with pocket
• Installs over the passenger seat and part of the tail section; fits bikes with a tail section width of 10.2" or less
• Measures 15" L x 27" W (front; 20" rear) x 16" H (from top of bag to bottom of overlapped sides); 7" H from top of bag to seat in front (5" in rear)

• Protect vital engine parts and cases from rocks and debris
• Clear anodized for corrosion protection and good looks
• Skid plates made from 3/16" 5052 H-32 aluminum
• Smooth underside won't snag when crossing logs
• Oil drain hole on all required models
• Heat-treated chromoly steel clamps keep plates mounted securely
• All mounting hardware included

The progressive factory springs are well known to be way to soft for most riders. Cogent Dynamics straight rate springs will give better control in the rough stuff and when loaded up.

Sold in pairs.

The .72 springs are 28% stiffer than stock and will be a great choice for most riders

Not compatible with Adventure Sport ES

Features:

• Clips on to brim of hat for hands free use
• Adjustable head for precise illumination
• Wide angle LEDs provide a flood of light
• Internal rechargeable li-ion battery (micro USB charging cord included)
• High and low settings, up to 4 hour runtime

Made with heat-treated carbon steel for longer wear life and reduced galling. Stock size, simple bolt-on procedure.

The Happy Trails SL (Soft Luggage) Racks work perfectly with the any soft luggage bags.

Features:

• Thoroughly tested 4th generation side racks
• Three point mounting system (includes mounting hardware)
• Strong 5/8" round tubing for the arms and SL mounting loop
• Racks add protection for the bike in the event of a tip-over
• Each rack is fabricated by expert craftsmen
• Racks finished with a black powder coat

Designed specifically for Dirt Drack racing for mini racers. Tread design can be customized to meet each rider's needs to provide superb traction and stability on any race track.

Not DOT approved for street or highway use!

Developed on the track and brought to the road. R&G engine case covers are made from 4mm polypropylene for strength, durability and looks that compliment your bike. Both sides included.

Complete high quality kit to replace the bearing and seals in the DRZ400 shock linkage. Includes the lower shock bearing.

This bracket mounts between the frame and your right footpeg bracket (works with both stock and low mounts) and allows you to adjust the slop out of the stock system. Puts the pedal in the ultimate location for immediate brake activation and eliminates unwanted pedal motion. Kit includes plate, adjuster bolt and lock nut and instructions.

Original Suzuki factory replacement levers for your DRZ400S/SM/E

Suzuki makes it almost impossible to replace your stock grips. It's much easier with a new throttle tube. Removable end cap for bikes with hand guards.

Lighter and stiffer than stock, these high quality straight rate springs are custom made specifically for the TW200. No adapter is needed! A proper rear spring will give a smoother more controlled ride. No more bottoming and better traction and confidence off-road.

If you (with all your gear on!) weigh up to 220 lbs, you want the 15 kg/mm spring. 225 lbs and up will want the 19 kg/mm spring.

• Stock Spring Rate '87-'16: 12kg/mm
• Stock Spring Rate '17-Cur: 15kg/mm

This nice piece replaces your plastic sprocket cover and protects your engine case from a chain derailment or failure. The 3/16" (5mm) thick steel plate is adjustable to accommodate 14, 15 and 16 tooth sprockets. Includes mounting hardware.

7" wire twisting pliers with return spring mechanism for easy and safe wire twisting.

The Happy Trails SL (Soft Luggage) Racks work perfectly with the Wolfman Expedition Dry Bags.

Features:

• Three point mounting system (includes mounting hardware)
• Strong 5/8" round tubing for the arms and SL mounting loop
• Racks add protection for the bike in the event of a tip-over
• Racks finished with a black powder coat

This is a vacuum operated automatic chain oiling system to keep your driveline adequately lubricated at all times.

When properly adjusted the oil will last thousands of miles between refills. The Scottoiler kit includes one 250ml bottler of oil which is good for 10000 miles of riding.

• Front pads: Sintered Pads are best for regular riding. Long life, and good performance in all conditions
• Rear shoes: Organic brake pads contain man-made high-performance fibers that are used for their light weight, high strength abrasion resistance and thermal stability.

Happy Trails exclusive Paris Dakar Nerf design for the ultimate in KLR650 protection. Loops of 5/8 inch tubular steel protect the expensive fuel tank and shrouds on your bike.

Included in this package is the fourth generation engine guard-highway peg combination giving the rider many more choices in riding positions for greater comfort mile after mile. The highway pegs provide bonus protection for the engine side cases, and they easily fold-up when not in use.

• Engine Guards require the Highway Peg kit for installation (included)
• Engine Guards cannot be run with the HT radiator/reservoir guard system
• Engine Guards are not compatible with the stock plastic skid plate

This is a high-quality seat cover done by Moose for the KLR. This is a replacement cover only, no seat foam and you must install on your existing pan with existing foam.

• Heavy duty marine grade vinyl
• UV protected for long life
• Double stitched for durability

Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!

Complete high quality kit to replace the bearings and seals in the swingarm pivot.

An optional add on to your ProCycle Top Rack to relocate your rear turn signals with ease.

A set of front and rear brake rotor bolts. These bolts already have thread lock compound applied to the threads.

Installing new turn signals or brake lights and need to find the 'HOT' wire, or are you just trying to find out if a specific wire has power going to it? Either way, this test light can help you locate shorts, open, and voltage on 12-24 volt DC circuits.

The Happy Trails SL (Soft Luggage) Racks work perfectly with the many different bags.

Features:

• Three point mounting system (includes mounting hardware)
• Strong 5/8" round tubing for the arms and SL mounting loop
• Racks add protection for the bike in the event of a tip-over
• Racks finished with a black powder coat

• Sintered Pads are best for regular riding. Long life, and good performance in all conditions
• Sport Carbon pads are made for fast riding in dry conditions. Not recommended for mud, water, or sand

Services two Pivot Pegz and fits MK2, MK3 and MK4 Pivot Pegz

Kit Contents:

• Two pivot tension springs
• Two lock nuts
• Two washers
• Six o-rings
• Two split pins
• Pivot Pegz sticker and instruction sheet

Fits perfectly under the stock seat. Made from 1000-denier Cordura. Cordura is water-resistant and dries quickly. Mounts to seat frame with 4 hook & loop velcro straps. Includes a shoulder strap for easy carrying.

Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm. Lo-pegs are down and back 1/4".

Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm. Lo-pegs are down and back 1/4".

The tension system integrated in this loop is a Green Chile innovation. You can add the ring tension loop to any 1" flat webbing system and have an instant upgrade. Even if you wear out the elastic in this loop it will not fail.

SPECIFICATIONS

• Heavy Duty 1" Metal Ring
• Heavy Duty Rectangle Ring to assist in managing slack in the webbing
• Climb-spec tubular nylon webbing body

Superior strength and protection against larger debri as well as small rocks etc.

If purchasing bash plate you will not need to purchase, the oil cooler guard is already incorporated into the bash plate.

radiator stone guard is machined from 4mm aluminium 5083 plate. The extra thickness of material provides superior strength and protection against larger debri as well as small rocks etc. Radiator guards can be fitted in approx ½ hr or less using basic tools. All radiator guard mounting hardware is supplied where necessary.

B&B Off Roads KTM 950 Super Enduro bash plate is made from 5mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider. All bash plates are supplied with the necessary stainless clamps and bolts where possible. All bash plates have a polished finish and have foam or rubber where required.

The KTM 950 and 990 adventurer luggage Rack is made from 5mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider.

All Carry/Luggage Racks are supplied with the necessary stainless clamps and bolts where possible.

DIMENSIONS

• Total Width Approx 35cm, Width of flat surface approx 31cm
• Length of flat surface approx 30cm

Our KTM 950 Super Enduro Luggage Rack is made from 5mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider.

All Carry/Luggage Racks are supplied with the necessary stainless clamps and bolts where possible.

DIMENSIONS

• Total Width Approx 35cm, Width of flat surface approx 31cm
• Length of flat surface approx 30cm

B&B Off Roads Honda CRF50, CRF70, XR50 & XR70 bash plate is made from 4mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider.

All bash plates are supplied with the necessary stainless clamps and bolts where possible.

All bash plates have a polished finish and have foam or rubber where required.

Standard (OEM Diameter) Solid Mount Wave® Rotor

Every high-quality, Galfer-patented Wave® rotor is made from a proprietary mix of virgin high carbon 420 stainless steel, laser cut (never stamped), double disc-parallel ground to assure perfect parallel flatness and heat treated to each specific application. KBA and TUV approved. Seamlessly replaces stock rotor. Full instructions provided along with any technical help needed.

Rear fender carry all rack by Flatland Racing

This carry rack is solid and durable made from 5052 aluminum and with its sleek design it will not catch on your clothes or nature.

It is an easy install and will allow you to strap your cooler, lunch box, tools, or whatever on the back of your Honda.

Comes complete with all hardware and easy install instructions. 

A somewhat neutral cross-sectional shape for improved handling and stability for light weight supermoto bikes.

Improved wet and dry performance.

Tubeless and H rated (max speed of 130 mph)

This product is a windscreen lip that will offer more protection from the wind and weather. These mount directly onto your existing windscreen.

Billet sprocket carrier from Warp 9 Racing. Available in several colors .

The little light that can! Don't be fooled by the mini size, big light comes out of this bad boy.

New design for 2021 featuring more durable, positive push button switch, metal handle bar mounts and options to allow this light to work for many applications. Switch, cords, strain reliefs and optics for optimal water resistance, ruggedness and performance.

It uses a go pro type mount with an aluminum platform to mount almost anywhere. Also included is a handle bar mount (mount on center of bars). No plastic parts on the light head.

Choose the optional SS platform to mount the light above the bars per two of the identified photos. (Fits all stock 7/8 and 1 1/8 bars. Not for flexbars)

Included is a rubber covered handle bar mounted switch with 2 power level settings 50% and full on.

Combo beam pattern, spot and wide beam in one light.

Compatible with Go Pro mounts, Perfect for modern EFI bikes.

• Includes basic wire harness
• 5000 lumens, 
• Spot and flood beam in one light
• 28 watt power draw.
• 2 year warranty, does not include crash damage, bent and or broken wires.
• 4 inches long by 1.350 high

• Lightweight levers are CNC-machined from aluminum
• Reach to the lever is adjustable to six positions