Search Products

Use this installation tool from Cogent to be sure that your Cogent Drop-in Dynamic Cartridges are installed correctly. A strong magnet in the end holds the cartridge firmly while you lower it into your fork leg. Then slide the spring over the tool until it holds the DDC down, then gently remove the tool. That simple. Never again question if it is properly seated on the damper rod.

Works equally well for removal when you need to change your fork oil. Also works great with Race Tech Emulators.

• Allows precise valve lash adjustment without disturbing the setting when the lock nut is fastened
• Knurled knob on adjuster drivers ensure a precise and secure grip
• Integrated repositionable wrench handle holds the lock nut while the drivers are used to loosen or tighten the valve adjustment screw

Set includes:

• (1) 10mm steel socket wrench
• (1) 3mm square tappet adjuster

With a Haynes manual, you can do it yourself…from simple maintenance to basic repairs. Haynes writes every book based on a complete teardown of the motorcycle. Haynes books have clear instructions and plenty of photographs that show each step.

• Step-by-step procedures
• Easy-to-follow photos
• Complete troubleshooting section
• Valuable short cuts
• Color spark plug diagnosis

Complete coverage for your Yamaha Trail Bikes covering PW, RT, TT-R and XT225/350 models for 1981 thru 2000.

Hard anodized oval shaped aluminum muffler with a TIG welded reinforced muffler bracket and red powder coated stainless steel end tip. Sleek muffler design gives you lots of clearance and it has a removable screen-type USFS approved spark arrestor. Head and mid-pipe are constructed from 304 stainless steel. Entire unit is pounds lighter than stock and gives great horsepower and torque gains throughout the RPM range.

All handmade in the USA with a 1 Year Limited Manufacturers Warranty.

Reduce exhaust leaks with this new OEM exhaust gasket. This gasket goes between the header pipe and the cylinder head.

We recommend Anti-Seize on exhaust fasteners.

Reduce exhaust leaks with this new OEM muffler gasket. This gasket goes between the rear tail/muffler pipe and the header pipe.

DG Performance exhausts help your engine breathe better, resulting in increased throttle response, power and torque.

The V2 Series Slip-On muffler features:

• Lightweight aluminum body
• Stainless steel inlet tube
• TIG welded components
• Great new look

Standard sound level is approximately 98 db and quiet core inserts are available separately.

This Lightweight Slip-On weighs approximately 5.5 lbs and bolts directly to the stock headpipe.

It is equipped with a US Forest Service-approved spark arrestor.

Their rear racks are great for adding the extra storage needed for your next adventure. They are the perfect size for a backpack or small duffel bag. Their steel racks are built to handle any riding style you throw at them, now Rotopax ready! This is the ENDURO Series XT225 Serow rear rack which measures 10 inches wide and 12 inches long.

Easy to Install

• Works great for mounting Pelican and Seahorse cases, or any other hard case. Givi compatible.
• Holes are in place to accept Rotopax mount with no drilling required.
• Stainless steel mounting hardware and instructions included.
• Fabricated with mild steel, MIG welded, and finished with a semi gloss black industrial grade powder coat.
• Weighs 3 lbs, 10 inches wide, 12 inches long.
• Works with stock tool bag. This requires an extra hardware kit available for free by request only.
• Rear rack only, no Rotopax mount or side racks included.

Nomadic Racks makes this beautiful rack for the XT225. 3 piece unit that is CNC laser cut from 1/8" 5052 plate aluminum with a semi-gloss industrial black powder coat applied. Final surface space is 9 x 14 with a weight just under 2 pounds.

With all the hardware included and excellent instructions, mounting this rack to the 4 mounting points is usually no more than a 15 minute affair and no modifications are required to your XT.

There are numerous strap and bungee holds making for a very versatile little unit. It is also totally compatible with RotoPax mounting kits and Givi top cases.

Cycle Racks Bag Supports can used for many different Cycle Racks and can be used on either the front or rear rack.

When they developed these, they wanted a functional, yet "Easy On- Easy Off application. The pig tail hook goes up, over and underneath the bar of the rack, they can also be used upside down on the rear rack as side boards. To install them, wing them out, slide them in place and then wing them back down. Simply reverse the process to remove them.

Rok-Straps are supplied to secure them in place. They are pre-drilled to accept the pattern of the Roto-Pax Pack Mount (sold separately) so you can carry fuel or attach them to your own bags.

They are sold together in a set of one right support and one left support.

COLOR: Black

The Front Rack gives a lot of options for functionality.

CycleRacks are made out of Schedule 40 11/16 black steel pipe, bent in a press, and welded together in a jig.

All of their products are 100% made in the USA. If the rack is ever broken for any reason, CycleRacks will replace it for free, you just pay the shipping.

CycleRacks are made out of Schedule 40 11/16 black steel pipe, bent in a press, and welded together in a jig. All of their racks have the same platform, 18" wide by 12" deep. Includes lower mount hardware.

All of their products are 100% made in the USA. If the rack is ever broken for any reason, CycleRacks will replace it for free, you just pay the shipping.

Replace those worn out brake pads with quality EBC replacements.

• Pads are Sport Carbon X technology
• Graphite with Kevlar for optimum performance

Replace those worn out brake pads with quality EBC replacements.

Premium quality EBC Rear brake shoes.

• EBC brake shoes are radius ground, and edge trimmed
• Lead out chamfers at lining ends

Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.

The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.

• Significantly improves response and feel over factory rubber lines
• Largest performance improvement for your money over any other braking upgrade
• Stainless steel hose resists abrasion and puncture
• Teflon core does not degrade over time like rubber lines
• PTFE Dupont 64 Teflon® hose
• Feature a heavy-duty stiffener sleeve and route just like the factory lines
• Proprietary, premium fittings
• Banjos utilizes a unique machined channel and sealing surface for leak-free installations
• R&D and engineered in the USA
• GBrakes USA controls the manufacturing process, ensuring the highest level of quality control

Standard 1157 bulb holder socket for dual filament bulbs.

• Clear bulb
• 6 Ultra Bright, LED chips for maximum illumination
• Low heat. Won't melt lens
• 12V
• Low voltage draw
• High shock and vibration resistance

This replacement lens has a clear panel on the bottom to illuminate your license plate. 

Allows you to bolt your license plate directly to the rear fender. 

Does not fit Australian DR650.

This device will pulse your brake light automatically. There are over 1000 possible pattern combinations with individually programmable Flash Speeds, Pre-Delay, and Flash Durations, as well as a disable feature to disable the unit. This device gives the end user the widest range of possibilities for customizing your tail light safety flash. With simple programming setup using only your brake lever, their is no disassembly or removing of the seat required to change the programming on the device.

Features:

• Independently programmable flash speed, flash duration, and pre-delay
• Works for LED or Standard Bulb Tail Lights
• All Solid State design
• Meets or exceeds OEM load rating specifications
• Over 1000 possible flash pattern combinations
• Simple programming setup with your brake lever
• Extremely compact unit size; 20mm x 20mm x 12mm

Now available in the original version or the Ultra version. The original uses the front two emitters for low beam and then switches to the rear two emitters for high beam. The Ultra uses the front two emitters for low beam and then runs all 4 emitters on high beam at a reduced wattage. Wattage is 38 watts on low and 38 watts on high.

This bulb uses 4 Cree XHP 50 emitters, capable of more than 2500 lumens each. At 5000 lumens on each function, this is the brightest Cyclops H4 bulb.

• All metal construction for bases and collars
• Better thermal efficiency 
• Better beam pattern distinction between high and low beams
• 5600k
• 38 watts 
• Removable metal base plate for easy install.
• Screw on connectors at driver
• Standard H4 connector
• High/Low Beams

*UNIVERSAL PART, PLEASE CHECK YOUR APPLICATION FOR FITMENT

This is a standard H4 bulb that has a 80 watt low beam and a 100 watt high beam. This is an easy lighting upgrade that should not over tax a stock charging system.

The SignalMinder unit is designed as a plug-in accessory for many Japanese bikes. SignalMinder uses a microprocessor to cancel the turn signals at one of three selectable time outs; 10, 20 or 30 seconds.

You can also make it so that all four of your signal lights also act as running lights and establish a dual-channel system on your bike. With the dual-channel system, when you activate the RIGHT turn signal three times in succession, you get 4-way hazard flash lights.

Connecting the 12 volt supply from the brakes to the SignalMinder, also allows for a brake flash option.

There are many options and configurations using this electronic tool.

No wire cutting required. The kit includes Scotchlok connectors to tap into existing wires.

A replacement Clarke Gas Cap that fits most Clarke Gas tanks. Comes with rubber gasket.

The new 4.1 gallon fuel tank from Clarke. Carries almost 2 more gallons than the stock tank. Available in Blue, Black, Silver, White or Natural

This gasket set is the same as the Complete Gasket Set above but includes all the necessary oil seals as well.

Fresh gasket for the ignition side cover.

Complete Gasket Set includes all the gaskets necessary to rebuild the entire engine and transmission, including valve seals.

Top End Gasket Set is designed for a piston replacement job and includes:

• Head Gasket
• Base Gasket
• Intake Gasket
• Exhaust Gasket

Time to adjust your valves? Here are the O-Rings that fit in your Valve Covers on your Yamaha. Keep the oil inside your motor and grime out! This kit includes both O-Rings. Be sure to grab the feeler gauges and a special wrench to aid in adjusting your valves.

Here are the O-Rings you need when you perform an oil change. The largest one and the smallest one go inside the oil filter housing cover. The second largest one goes on your oil drain plug. The second smallest one goes on your oil fill plug. Replacing these O-Rings regularly will help keep your engine from seeping oil.

Adjusting your valves or setting your cam chain tension? Here are the O-Rings that fit in the TDC sight plug and the crankshaft nut access plug.

Gasket for the engine case cover over the clutch. Doing any clutch work, you probably want to replace this gasket so you don't have any leaks when you are all done with the project.

Heavy-Duty clutch springs

• 15% stiffer than original
• Minimize clutch slip
• Reduce plate wear
• Improve power to ground

Providing unbeatable performance and exceptional value, Hiflofiltro is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide. The filters are also supplied to original equipment manufacturers as well as private label brands.

Iridium spark plugs are made with premium quality materials.

Iridium plugs last longer than standard ones, meaning you won't have to replace them as often.

• The ultimate in the evolution of spark plug technology and performance from an industry leader
• The iridium electrode is 25% smaller than a platinum electrode, and it's just 1/4 the size of a conventional nickel electrode
• Ultra-small diameter center electrode reduces voltage requirement and extends ignition system life
• Metal shell plating has enhanced anti corrosion qualities

Sold individually, unless otherwise stated.

E3 Resistor Spark Plugs

The unique design of the electrode maximizes the power generated by the spark plug through Diamond Fire technology. This electrode combines advanced performance capabilities and innovative technology to enhance the shape of the flame kernel. Consequently, the flame front ignites the air/fuel mixture more rapidly, accelerates heat transfer into the combustion chamber, and creates a more concentrated pressure front, facilitating a quicker pressure rise during the cylinder power stroke. The outcome is a more efficient combustion process and improved engine performance, making this a truly premium spark plug.

Keep your motor running right with fresh spark plugs!

NGK is one of the world's largest manufacturer of spark plugs, whose products are used as original equipment (OE) on countless motorcycle and automobile models.

• High-quality materials and superior construction for serious power and reliability
  • Pure alumina silicate ceramic insulator provides high strength and better heat transfer
  • Deep-seated copper core for a wider heat range
  • Nickel alloy tip for longer life
  • Trivalent metal plating provides superior anti-corrosion and anti-seizing properties
• Choosing the right high-quality plugs prevents fouling from running too cool and preignition from running too hot
• NGK plugs available for almost every application and riding style

Tune your stock carburetor for better power and response, easier starting and quicker warm up. Mikuni main and pilot jets.

• Main Jets: 127.5, 130, 132.5 &135
• Pilot Jets: 42.5 & 45
• 5 Shim washers for raising the needle

No Toil air filter to replace the stock unit. Fits the stock airbox using the standard guide and frame. It requires foam filter oil to properly trap dirt particles. Don't forget the Evolution Air Filter Oil kit from No Toil.

• Made of flame-laminated dual-layer foam, bonded with the highest quality glue to stand up to the roughest and toughest of any style of riding or terrain
• This filter, used with No Toil foam filter treatment, provides the best air filtration system in the world
• Fully open-cell structure for highest airflow and maximum protection
• Heavy-duty glue provides protection from all solvents
• Wide soft sealing ring for extra protection
• Flexible seams prevent cracking
• Original OEM size

A quality foam Air Filter to replace the stock one. Uses the same guide and frame as the stock unit. It requires foam filter oil to properly trap dirt particles. Don't forget the Evolution Air Filter Oil kit from No Toil.

• Designed to fit in the factory air box exactly like original filter
• The best selling replacement air filter for competition motorcycles and ATVs
• Unique two stage design allows for easy and complete cleaning
• Dual layer of foam, can be serviced separately
• Thin Ultra Seal base is virtually impossible to tear and has a built-in "Grease Groove"

Complete kit to rebuild OEM carburetors.

High quality replacement master link for the DID 428 non-oring chain

Clip style master link for the EK 428 O-Ring chain. Keep one in your tool kit for trail side repairs.

High Quality chain. You'll need to cut to fit your sprocket combination.

Stock gearing uses a 45 tooth rear sprocket

The 50 tooth rear sprocket will give you much lower gearing for off-road use. You will need a longer chain for this rear sprocket, please order the 130 link chain to fit with this larger sprocket, it may need to be shortened to fit correctly.

• Stock gearing uses a 15 tooth sprocket
• Use a 13 tooth sprocket for REALLY low off-road gearing
• Use a 14 tooth sprocket for off-road performance
• A 16 tooth sprocket will give you lower RPM at highway or street speeds

Helps protect vulnerable fork tube and seal from dust, dirt, and corrosive elements. These are sewn into a tube and require that you drop your fork tubes down out of the triple clamp for installation. Can still be slid up for easy cleaning. Sold in pairs

High quality fork boots. Sold in pairs.

Currently only available in Yellow.

Damping Rod style forks are notorious for being too harsh, too mushy and too easy to bottom. Gold Valve Cartridge Emulators remedy this problem by controlling the compression damping with a tuneable valve. The Emulator sits on top of the damping rod and is held in place by the main spring.

Simply put; Emulators make damping rod forks perform like well-tuned cartridge forks. Installation and tuning for any condition or rider preference is very straight-forward. 

Simple to install and completely tunable for all conditions and rider preferences.

These Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. No disassembly of your forks, no drilling of damper rods. Just change the oil to 5w and install the DDCs under the springs and hit the trails.

Stiffer fork springs are required to realize the full benefits of the DDCs. .42 kg/mm springs are the springs recommended for just about anybody out there. Please call if you have any further questions.

The DDCs are not recommended for use with progressive springs.

The DDC Install/Removal Tool which makes installation that much easier.

Low friction 'triple lip' seal design. Oil seals last 3-4 times longer that OEM seals. Kit includes Fork Seals and dust wipers.

The Modoc is an excellent replacement for the stock shock. With adjustable rebound damping and preload, you can tailor the performance to match your riding style.

Select the spring you want installed based on the load you plan to carry. For most riders, the 7.1 kg/mm spring will suit you perfectly. Weigh more than 250 lbs, or are loaded to the max, think about the 8.1 kg/mm spring. Please call with any questions.

Complete kit to replace the bearings and seals in the XT225 swingarm pivot.

Included in this kit are .42 kg/mm fork springs, Cogent DDC (Drop in Damper Cartridge) performance cartridges and two bottles of 5w fork oil.

These springs are custom wound specifically for the XT225. Stiffer than the .36 kg/mm stock springs, these will make your front perform significantly better. Combine them with the Cogent DDC's and you will be very happy with the results. Sold as pairs.

The plastic fitting that secures the stock choke cable to the carburetor is delicate and easily broken. A broken fitting can cause hard to solve idling and running problems.

CNC machined from billet aluminum and anodized black or blue. If you want to retain your handlebar mounted choke this may be the solution.

  These no longer fit the new version of the ProCycle Remote Choke Cable. Will not work with the long or short reach choke knobs.

Corbin seats are carefully designed to provide a comfortable riding position. They are firm and supportive which allows you to ride all day without fatigue unlike the stock seat. Comfort Cell Foam retains resilience and doesn't crush down like the stock seat foam.  On the top, Corbin covers are only the highest grade of weather resistant materials for durability and long life.  Corbin seats install the same as similar to stock with two bolts into the chassis which provides a closer fit to the bodywork and tank.

New wider seat to help keep comfortable on that long commute or dual sport ride. The added width and foam density will help keep the seat from being an item to stop you from going on that ride or enjoying the bike. 

Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!

Available as a Foam and Cover Kit for OEM pan. It DOES NOT include the pan.

Don't hit the trails without these tire irons. Each 10 inch forged steel tire iron has a hex wrench on one end. A 22mm and a 19mm that will remove both axles. Rounded spoon end minimizes pinched tubes and scarred rims.

Contains all of the bearings and seals required to re-fit a wheel.

Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.

Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.

Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.

Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.

The rubber coated outside diameter creates an optimum seal at the hub.

Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.

A set of feeler gauges so you can adjust the valves on your Yamaha. Yamaha says that when the bike is cold, the Intake should be between .002" and .004" and the Exhaust should be between .006" and .007".

This set includes one gauge with a .004" on one end and a .005" on the other for your intake side and another with a .006" and .008" for the exhaust side.

This adapter will give you more mirror choices.

Yamaha mirrors have reverse threads on the right (throttle) side of the handlebars. This adapter allows you to mount a mirror with standard 10mm threads on the right side of your handlebar. This opens up many options for your mirrors, choose any 10mm mirror for your Yamaha.

• Torque spec: 5 Nm

OE style clutch or brake lever.

• Quality Aircraft grade A-360 aluminum for strength & durability
• Designed to exceed OEM specifications, built to resist breakage
• Durable hard coating
• Designed to fit OEM perch

• Machined and knurled 6061 billet aluminum. Actual color may vary
• Removable end cap for easy hand guard installation
• Works with standard housing

Opens your throttle 15% faster. No more 'double handfuls' to get it wide open. Removable end cap for bikes with hand guards.

Throttle, Clutch or Speedo cables.

TW200 billet oil drain cap plug. 

Nice billet aluminum replacement for the old cast oil drain cap.

The Shorai LFM Standard Recommendation is the best overall pick for most applications, and has been selected to give strong cranking performance and long lifespan.

• Capable of holding a charge for up to one year without maintenance
• Two to four times the life of lead-acid batteries
• A Battery Management System that protects the battery from over-discharge.
• Carbon Fiber Composite case
• Stronger cranking for better starts
• Environmentally friendly, just discharge and dispose
• Ultra light and compact

Measures 4.5" x 3.5" x 2.28"
Weight (lbs): 1.34 lbs
Weight (kg): 0.61 kg
Cold Cranking Amps: 135
Polarity: [- +]

Each Shorai battery includes self-adhesive foam panels to achieve a snug fit in your battery box.

The Shorai LFM Duration Recommendation is the best overall pick for most applications, and has been selected to give strong cranking performance and long lifespan. 

• Capable of holding a charge for up to one year without maintenance
• Two to four times the life of lead-acid batteries
• A Battery Management System that protects the battery from over-discharge.
• Carbon Fiber Composite case
• Stronger cranking for better starts
• Environmentally friendly, just discharge and dispose
• Ultra light and compact

Measures 4.45" x 3.5" x 2.28"
Weight (lbs): 1.52 lbs
Weight (kg): 0.69 kg
Cold Cranking Amps: 210
Polarity: [- +]

Each Shorai battery includes self-adhesive foam panels to achieve a snug fit in your battery box.

Built with the latest in Lithium Ion Polymer Technology. All components are designed, manufactured, assembled and packed in one location assuring high quality and consistency. Besides it's extreme lightweight (50% to 70% lighter than standard lead-acid batteries) it also features a built-in LED test gauge and the ability to mount it in any position. There is no hazardous acid or heavy metals and it is non-explosive and non-combustible.

The Firepower features Increased cranking amps over lead acid batteries and has a very fast recharge cycle and can be brought up to a 90% charge within 6 minutes and also has 6 to 12 times more cycle life when compared to lead acid batteries. A 2-year warranty insures that your investment is protected.

145 CCA 12V/28.8WH
Package Dimensions: 4.75" x 3.00" x 4.50

Built with the latest in Lithium Iron Polymer Technology. All components are designed, manufactured, assembled and packed in one location assuring high quality and consistency. Besides extreme lightweight (50% to 70% lighter than standard lead-acid batteries) it also features a built-in LED test gauge and the ability to mount it in any position. There is no hazardous acid or heavy metals, it is non-explosive and non-combustible. Integrated BMS (Battery Management System) with cell balancing and overcharge protection

The Firepower features Increased cranking amps over lead acid batteries and has a very fast recharge cycle and can be brought up to a 90% charge within 6 minutes and also has 6 to 12 times more cycle life when compared to lead acid batteries. A 3-year warranty insures that your investment is protected.

Rated at 220 CCA (Cold Cranking Amps)
Package Dimensions: 4.75 x 3.00 x 4.50

These are the first batteries with built-in jump starting. They intelligently monitor their status, and just before going completely dead, puts itself to sleep with just enough energy to get your vehicle started again. Simply press the RE-START button located on the battery, start your bike and ride away.

These are an extremely lightweight (2.5 lbs.) high-powered Lithium-Ion replacement battery for motorcycles. These batteries offer the first Battery Management System (BMS) found on a powersport battery and includes low-voltage cut-off, over discharge, over-charge, and thermal protections with real time lithium-ion cell balancing. Use of a lithium specific charger to maintain the life of the battery is highly recommended.

Product Size is 8.4"L x 5"W x 2.2"H. If you need spacers, select the optional Foam Kit to pad the battery in the battery box.

A motorcycle rectifier-regulator is a crucial part of the charging system, acting as a charging control device to prevent damage to your battery and electrical system. These OEM-style units are direct replacements, providing the proper fit and the expected performance on your bike

We start with Excel or Sun rims, OEM hubs, and Buchanan's heavy gauge stainless steel spokes. Rims and spokes are precision machined for a perfect match to your bike.

Our pro shop then laces and trues your wheels to perfection, giving you the highest quality set of custom wheels available.

• New OEM hubs with bearings and seals installed
• Excel 2.5" x 17" or Sun 2.75" x 17" front rim
• Excel or Sun 3.5" x 17" rear rim
• Buchanan's stainless steel heavy gauge spokes and zinc-plated nipples

Add tires to your wheel order and we will throw in tubes and mount and balance them at no additional charge.

Our Tool Tube mounts in place of the little stock tool carrier. The tube is made from 3 1/2" O.D. ABS pipe. It's held by 2 strong powdercoated steel straps. Both ends are sealed with waterproof expanding plugs. This is the ideal way to carry those items you always want to have with you on every ride. Tube is approx 13" long. Long enough to carry your Tire Iron Wrenches.

You can now order your Tool Tube with a Locking End cap, mini padlock and keys included, on the exposed end.

If you already have a Tool Tube you can order just the Locking End Cap and lock.

Made from strong and lightweight 4mm thick aircraft aluminum.

Protects vital engine parts from rocks and debris.

Custom fit to your specific bike model.

Oil drain hole for easy access.

All mounting hardware included.

Tapered roller bearings provide decreased maintenance, less wear, smoother operation and longer life.

This set of high quality replacement steering stem bearings includes:

• Upper and lower tapered bearings
• Upper and lower bearing races
• Upper and lower seals