Really like your stock vacuum petcock and never having to worry about turning it off? Did the seals go bad and it leaks? Plugged up? Well, whatever your troubles, here is your replacement. Vacuum operated so you never have to turn it off! Just like the stock unit. Includes mounting bolts with washers, fuel line, clamps and a protecting coil wrap.
- Use a rear sprocket with a higher number of teeth for quicker acceleration and technical offroad trails.
- Use a rear sprocket with a lower number of teeth for lower engine rpm's at highway speeds.
- Stock size is 50 teeth.
We recommend using the Rear Sprocket Bolt Kit when installing most aftermarket sprockets on your TW.
Low peg mounts for the DR From Wirtz Wire. These are different than our other mounts for several reasons. First, these are designed around the stock pegs. All of the pegs in this section will fit these mounts. Another difference is that these mounts are offered in a low mount as well as a low and rearward mount. These are 'wire EDM' machined from solid 1018 steel bar stock, and are not welded anywhere. They are powder coated black for a great look. Both mounts move the pegs down 2" while the low and rear mounts also move the pegs back 1.3".
Kit comes with new mounts, longer bolts and a longer brake switch spring that will be needed. Pegs are optional, your stock pegs will work.
The upper image shows the low and rearward mounts while the one below that is of the just low mounts. If you look at the two images below that, you will see that these are the low and rearward pegs for both sides of the bike.
Their rear racks are great for adding the extra storage needed for your next adventure. They are the perfect size for a backpack or small duffel bag. Their steel racks are built to handle any riding style you throw at them, now Rotopax ready! This is the ENDURO Series CRF300L rear rack which measures 10 inches wide and 12 inches long.
Easy to Install
- Works great for mounting Pelican and Seahorse cases, or any other hard case. Givi compatible.
- Holes are in place to accept Rotopax mount with no drilling required.
- Stainless steel mounting hardware and instructions included.
- Fabricated with mild steel, MIG welded, and finished with a semi gloss black industrial grade powder coat.
- Weighs 3 lbs, 10 inches wide, 12 inches long.
- Works with stock tool bag. You can remove the seat with no interference from the luggage rack.
- Rear rack only, no Rotopax mount or side racks included.
Their rear racks are great for adding the extra storage needed for your next adventure. They are the perfect size for a backpack or small duffel bag. Their steel racks are built to handle any riding style you throw at them, now Rotopax ready! This is the ENDURO Series CRF450L rear rack which measures 10 inches wide and 12 inches long.
Easy to Install
- Works great for mounting Pelican and Seahorse cases, or any other hard case. Givi compatible.
- Holes are in place to accept Rotopax mount with no drilling required.
- Stainless steel mounting hardware and instructions included.
- Fabricated with mild steel, MIG welded, and finished with a semi gloss black industrial grade powder coat.
- Weighs 3 lbs, 10 inches wide, 12 inches long.
- Works with stock tool bag. You can remove the seat with no interference from the luggage rack.
- Rear rack only, no Rotopax mount or side racks included.
Their rear racks are great for adding the extra storage needed for your next adventure. They are the perfect size for a backpack or small duffel bag. Their steel racks are built to handle any riding style you throw at them, now Rotopax ready! This is the ENDURO Series CRF250L rear rack which measures 10 inches wide and 12 inches long.
Easy to Install
- Works great for mounting Pelican and Seahorse cases, or any other hard case. Givi compatible.
- Holes are in place to accept Rotopax mount with no drilling required.
- Stainless steel mounting hardware and instructions included.
- Fabricated with mild steel, MIG welded, and finished with a semi gloss black industrial grade powder coat.
- Weighs 3 lbs, 10 inches wide, 12 inches long.
- Works with stock tool bag. You can remove the seat with no interference from the luggage rack.
- Rear rack only, no Rotopax mount or side racks included.
Their rear racks are great for adding the extra storage needed for your next adventure. They are the perfect size for a backpack or small duffel bag. Their steel racks are built to handle any riding style you throw at them, now Rotopax ready! This is the ENDURO Series XT225 Serow rear rack which measures 10 inches wide and 12 inches long.
Easy to Install
- Works great for mounting Pelican and Seahorse cases, or any other hard case. Givi compatible.
- Holes are in place to accept Rotopax mount with no drilling required.
- Stainless steel mounting hardware and instructions included.
- Fabricated with mild steel, MIG welded, and finished with a semi gloss black industrial grade powder coat.
- Weighs 3 lbs, 10 inches wide, 12 inches long.
- Works with stock tool bag. This requires an extra hardware kit available for free by request only.
- Rear rack only, no Rotopax mount or side racks included.
Their rear racks are great for adding the extra storage needed for your next adventure. They are the perfect size for a backpack or small duffel bag. Their steel racks are built to handle any riding style you throw at them, now Rotopax ready! This is the ENDURO Series KLX300 rear rack which measures 10 inches wide and 12 inches long.
Easy to Install
- Works great for mounting Pelican and Seahorse cases, or any other hard case. Givi compatible.
- Holes are in place to accept Rotopax mount with no drilling required.
- Stainless steel mounting hardware and instructions included.
- Fabricated with mild steel, MIG welded, and finished with a semi gloss black industrial grade powder coat.
- Weighs 3 lbs, 10 inches wide, 12 inches long.
- Works with stock tool bag. This requires an extra hardware kit available for free by request only.
- Rear rack only, no Rotopax mount or side racks included.
Made of military aircraft grade 3/16" cast acrylic, this guard will protect your lens from roost, rocks and branches. Optical clarity of the acrylic ensures brightness and projection of your headlight are minimally effected while all the while protecting your headlight from impact and abrasion.
Guards are held to the headlight lens with an industrial strength hook and loop system on each corner.
First there was the Warp 9 "4-Finger" Lever, now there is the Warp 9 "3-Finger" Lever Exclusive to ProCycle. Yep, the original shorty (next item below) is a full 4-finger type lever. These are a full half inch shorter. You asked for 3-finger levers, and we had Warp 9 make them for us. Brake lever includes a nice billet clamp with nylon sleeve to allow the assembly to rotate on impact. Will not fit with the stock OEM wind deflectors.
Will not engage the clutch switch on 2010 and later models
Rigg Gear has created a couple of great roll top bags. These bags are 100% waterproof, made from 24 oz. Tarpaulin PVC and then electronically heat welds the seams. A roll closure with self-fastening webbing and quick release buckles keeps the top closed and sealed. The Tarpaulin is UV coated so clean-up is quick and easy. Each of these bags has a lifetime warranty!
Once topped off, you can fasten it to your bags, racks or whatever by four custom aluminum G-Hooks and webbing straps that are included with each bag. Each bag has a Tri-max 1680D ballistic nylon panel sewn on a side to be used on the bottom for wear resistance. This also serves as a comfort panel when the bag is used as a backpack.
*Each bag has sewn in loops that allow attachment of a set of shoulder straps so these bags can double as a backpack. Perfect for a day hike.
Each of the bag sizes is available in Black or Yellow. Main compartment measurement is 18" Long by 8" Dia. for the 15L and 19" Long and 10.5" Dia. for the 30L bag.
NOTE: 30L BLACK ONLY IN-STOCK
(NOTE: The 30L bag DOES include the straps, can also be purchased separately.)
Acerbis 5.3 gal tank adds function and great looks to your DR650. This high capacity fuel tank incorporates modern lines and high quality construction that can't be beat. Includes gas cap, petcock and all mounting hardware.
Installation of the Acerbis tank requires relocation of the front turn signals. Otherwise the stock signals will contact the tank at full lock. Our Turn Signal Relocation Brackets Move the front turn signals up and forward to clear the bigger tank.
Comfortable Oversize (or Fat Bar) Handlebars.
- Silver in color.
- Constructed of high-quality 7065-T6 aluminum
- Lighter and stronger than regular bars
- No-crossbrace allows flex to reduce shock and rider fatigue
- Oversize 1-1/8" diameter base reduces to 7/8" to allow standard-size controls/grips
- Etched alignment marks for fast and accurate positioning
- Flex Series pad included
- Works with stock controls and cables.
For bikes with factory 7/8" handlebars these will require the use of a 7/8 to 1-1/8 adapter (sold separate).
Engineered with precision and hand crafted with premium materials including Seat Concepts’ proprietary foam formula, the 8” wide One-Piece Rally Hard Adventure 2.0 seat is designed to provide you with an open cockpit for increased mobility during technical riding and traction ribs to help keep you planted.
Available as a complete seat only including seat base.
Width: | 8" (203mm) |
Height: | Same as OEM |
New wider seat to help keep comfortable on that long commute or dual-sport ride. The added width and foam density will help keep the seat from being an item to stop you from going on that ride or enjoying the bike. The Complete Seat comes with an aftermarket pan with the foam and cover kit assembled, ready to ride.
Width: | 9.5" (241mm) |
Height: | Same as OEM |
The One-Piece Comfort seat is 11” wide and designed to improve weight distribution and support when seated while still allowing the rider to move freely when standing. Built to withstand the rigors of adventure riding, the T7 One-Piece Comfort seats are designed with the rider in mind.
Available in multiple cover options and three different heights: low, standard, and tall. Whether you have a 26” or 36” inseam, Seat Concepts has you covered.
Available as a complete seat only, including seat base.
Height: Same as stock.
Width: 11"
Width: | 11" (279mm) |
Height: | Same as stock |
This is the ultimate in radiator guards! It will protect your fragile radiator from nasty front & side impacts.
This ultra tough guard is constructed from 1/8" aluminum and is easy to install.
All Flatland Racing radiator guards have rear mounting brackets for that extra support! All Mounting hardware is included.
FunnelWeb ProLine Filter Highlights:
- Optimum air flow for increased riding time
- Improved engine protection
- Extended filter change intervals
- Simple to install, clean and re-oil
- Easy fitment
Like all FunnelWeb filters, the ProLine Filter features profile cut, single layer, single density foam that doubles the external surface area of the filter without increasing the original filter size. The ProLine Filter traps dirt, dust, sand and mud over a larger area on its outer surface, ensuring optimal air flow is maintained for maximized engine performance and reliability.
The single layer, single density polyurethane foam has the added advantage of being easy to clean and the ability to maintain its original shape after numerous washes. Overall, compared with conventional foam filters, FunnelWeb offers more protection from dirt ingestion, has longer service intervals and maintains high airflow rates when dirty.
Not only are Pro Moto Billet Cargo Racks brutishly strong and functional, but they look great too. Each cargo rack is methodically engineered, then CNC machined on-site from a 1/2 inch thick plate of USA made 6061 aluminum by master machinists and then anodized black.
PMB uses only stainless steel fasteners for worry-free years of riding. Excellent instructions and all necessary hardware is included.
Need to mount your turn signals to your new Pro Moto Billet Rack? Just add a set of CNC machined aluminum Turn Signal Brackets for $15.95 and that will be no problem. See bottom image.
Yoshimura RS-3 that will slip right on to your stock header. Made by hand to the highest quality standards using the championship-winning racetrack experience and their extensive R&D facility ensure these pipes perform and will last.
Both full systems and slip-on mufflers include 96 dB sound insert/USFS approved spark arrestor installed in the muffler. Mid-pipe is stainless steel while the stainless RS-3 oval muffler design has a slim profile with an aluminum end cap.
Works on OEM header only!
- Eliminates the need to cut and splice wiring when using aftermarket turn signals or marker lights
- Plug into the OEM turn signal plug and then use bullet style connectors used on aftermarket lights
- To verify proper fitment, compare connector photos to OEM connector
- Sold in pairs
Fits Most Models
Keep your cables lubed up and working freely, with Motion Pro's Cable Luber. This tool is used to inject lubricant into any cable housing. Clamps over housing and cable allowing an aerosol can with nozzle to be connected. Once the lubrication solution runs out the far end, the cable is lubricated.
High-quality, direct replacement plastic kit includes:
- Front and rear fender
- Side covers
- Air box cover
- Radiator shrouds
Yellow kit is only available with white side covers
Add-on Headlight cowling fits S and SM models not "E" offroad model
Simplify self recovery with this quick deploy Z-Drag kit. It can sap your energy trying to get your bike unstuck. It can also fall in a way that makes it very difficult to pick up. The Z-Drag is a common rig to give you a mechanical advantage for reduced pull. The combination of roller cams provides a 4:1 pulling ratio for self recovery and a 5:1 ratio when you have help. A laminated instruction card is included in the bag.
Quick Deploy | No knowledge of rigging and knot work required. Our Z-Drag comes out of the bag rigged and ready to use. |
Color Coded | For simple operation. |
Locking Carabiners | Two climbing rated, locking carabiners for secure attachment. |
Lightweight | Approx. 3 pounds and small enough to pack on a motorcycle. |
Strong | Even though its small, it still has a 1000 pound working load. |
Versatile | With a 74' mainline you will always have enough length to get creative in a tough situation. |
Multi-Function Bag | The bag features MOLLE compatible webbing on the outside for external attachment. The bag can also be utilized as a dead man anchor. |
Storage | Comes in a 1000D Cordura storage bag. |
Recovery | Can be used for solo recovery or with help from friends. |
Trail Repairs | Can easily be used to hoist your bike from an overhead support for repairs and maintenance while traveling. |
Clearing Trails | Move fallen trees out or other obstacles out of the way. |
Camping | Can be used to hoist a bear bag, act as a ridge line for stringing a tarp, etc. |
Here is the little switch that mounts inside your brake or clutch lever perch and controls the brake light or clutch safety circuit. This switch often gets damaged in an unplanned dismount (aka: crash) or the plastic simply cracks from age. When this happens, you can find yourself chasing a short circuit that keeps blowing your fuse every time the brakes are applied. If this has happened to your TW, here's the fix!
Fits all TW200's. Includes a new cap and uses the stock petcock. Capacity is 2.7 gallons (stock tank is 1.8 gallons).
Clarke tanks do not come with a vent hose or vent cap.
Please note: All Clarke TW200 tanks have blemishes due to the mold used in their manufacturing process. Also, side panels are likely not snap into tank as they do on the stock tank.
RallZ is the most aggressive off-road adventure tire in the Motoz range. Its DNA is part desert race tire and part long distance adventure tire. An ADV tire designed in Australia for adventure and rally use. Based on the popular Tractionator Adventure but with more aggressive off-road traction in all weather extremes.
DOT ECER75 approved.
NOTE: Tubes can be run in Tubeless (TL) tires, but a Tube Type (TT) tire cannot be run Tubeless.
This device will pulse your brake light automatically. There are over 1000 possible pattern combinations with individually programmable Flash Speeds, Pre-Delay, and Flash Durations, as well as a disable feature to disable the unit. This device gives the end user the widest range of possibilities for customizing your tail light safety flash. With simple programming setup using only your brake lever, their is no disassembly or removing of the seat required to change the programming on the device.
Features:
- Independently programmable flash speed, flash duration, and pre-delay
- Works for LED or Standard Bulb Tail Lights
- All Solid State design
- Meets or exceeds OEM load rating specifications
- Over 1000 possible flash pattern combinations
- Simple programming setup with your brake lever
- Extremely compact unit size; 20mm x 20mm x 12mm
If you're like us, you hate the long floppy vent hose hanging off the cap of your aftermarket tank.
This one-way vent cap replaces the long hose with a short one only about 2" long. It allows air into your tank but prevents fuel from sloshing out.
Machined from billet alloy and anodized for good looks.
Not for stock fuel tanks!
Their best selling product to protect your bike, Flatland Racing skid plates are made from 5052 3/16" aluminum plate.
They are all hand tig welded together with side engine guards. Installation is easy with our clamps that grip tight.
Their skid plates offer clean out slots and oil plug hole, making oil changes simple. These are more durable than carbon fiber and plastic.
Mounting hardware and instructions included.
Big bore kit for the 2003-2005 CRF150F. A simple bore in bore kit that includes BBR's high performance camshaft and valve springs for added performance. This cam features higher lift and duration than stock. Complete kit includes piston, rings, pin, clips, BBR MX cam, valve springs and gaskets. This is the quickest way to add the most power to your bike. Great when combined with our exhaust system, Rev-Box, and Free-Flow airfilter. Requires machining of stock cylinder for installation.
- Adds up to 3.5 HP
- 67mm piston, pin, clips, and rings
- 10.75:1 compression ratio
- Includes head and base gaskets
- Makes more aggressive style of power
- Bike still starts easily and idles smooth
- Same camshaft as used by the BBR Race Team
- Requires professional boring of your stock cylinder
Remove the bulky stock number plate holder with our slim design- comes with LED number plate light.
- Quick and easy install
- Mounting hardware supplied
- Comes with clear LED tail, brake & number plate light
- No mods required for installation
- Available in polished or black PPA coating.
- Pre drilled to suit Australian licence plate
*Please Note: Brake light does not come with necessary/factory connectors. Some cutting, crimping, soldering of wires may be required for connection.
Parabellum LTD. has continued the highly demanded Rally Shield line by fitting up the 1993-present Honda XR650L. This is an upright Dakar Rally inspired shield, designed to protect the rider without interfering with off-road riding. For on-road riding the Rally shield protects the rider’s chest from fatiguing air blasts while keeping the head in clean air. Duck behind it in the cold or the rain to keep from experiencing the brunt of the elements. During off-road riding the Rally windshield protects the rider from mud, dust, roots, rocks, or branches without becoming invasive. Whether standing on the pegs or ducking behind it, you will be impressed at the protection it offers. Their Rally shields have been tested in the toughest conditions including an entire SORCS hare scramble season.
*The Rally shield for the XR650L is 12.5 inches tall 12.5 inches wide at the bottom and 8.5 inches wide at the top and is made from military grade 1/8 inch cast acrylic.
Clear lens, amber LED type lights. Short flexible stems. Very small, only 2 7/8" long. Requires a LED turn signal flasher to flash properly. 4 Pack
A real Heavy-Duty Chain Guide manufactured from 5mm (3/16") thick 5052 Aluminum. This guide will take a pounding and continue to put that chain right on the sprocket. The rub block is machined from UHMW plastic and can be positioned to fit just about any sprocket available for the DR. These are powder coated black for a great look and additional protection.
This complete fork upgrade kit includes stiffer fork springs and Race Tech cartridge emulators, as well as a set of top quality fork seals and fork oil to complete the job. Everything you need to transform your mushy stock forks into suspension that really works.
You can select from various straight rate springs or even 'Progressive Suspension' springs to customize the package to your needs.
- Rider and Gear up to 160lb. = 0.47 springs → 24% stiffer than stock
- Rider and Gear 160-225 lb. = 0.52 springs → 39% stiffer than stock
- Rider and Gear 255-275 lb. = 0.58 springs → 56% stiffer than stock
- Rider and Gear 275-325 lb. = 0.63 springs → 66% stiffer than stock
- Rider and Gear 325 lb.-UP = 0.70 springs → 84% stiffer than stock
The Powercore 4 spark arrestor muffler. FMF developed the Powercore 4 to increase the horsepower and torque throughout the entire power curve. Highest quality packing for long life. Removable spark arrestor included. Louder than the Q4. Approximately 99db stock or about 94db with optional Quiet Insert installed.
- Uses long-life muffler packing for increased packing life
- Forest Service approved spark arrester
Providing unbeatable performance and exceptional value, Hiflofiltro is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide. The filters are also supplied to original equipment manufacturers as well as private label brands.
You pay $3.50 per filter with our value 10-pack!
Race Tech Cartridge Emulators make damping rod forks perform like well-tuned cartridge forks. Emulators are tunable valves that sit inside your forks on top of the damping rods and are held in place by the fork springs. Simple to install and completely tunable for all conditions and rider preferences.
Their baffle was designed to replace the stock insert. The baffle produces a nice note compared to the de-restricted stock version and dyno test results showed an increase on 2 hp up top.
A noise test on the insert was conducted at the EPA Victoria Vehicle Test Station at Macleod under controlled conditions with Class 1 meters.
Tested Bike | ADR Signature dB(A) & test RPM | ADR tess with B&B Tip |
---|---|---|
Suzuki DRZ 400 | 93 dB(A) @ 3375 RPM | 97 dB(A) @ 3375 RPM |
Some extra details:
- The ADR test is conducted at an engine speed which is 50% of the engine rpm at which the engine develops maximum power. However, this engine speed is determined when the bike is in restricted form, with a throttle restrictor that stops the throttle being fully opened. This is why the ADR engine test speeds are so low. However, they are the engine speeds used to determine compliance.
- On the ADR test, the B&B tip was over the signature noise emission, but a tolerance of 5 dB(A) is allowed before prosecution would be initiated. With this tolerance, the insert would not be prosecuted as it is just 4 dB(A) over the signature.
- When tested with the standard OEM tips (as fitted when delivered from Suzuki Australia), the Suzuki came in at 95 dB(A) for the ADR test
Does not contain a spark arrestor. Check local laws on spark arrestors before purchase.
Replacement Exhaust Pipe Retention Spring
- This swivel spring replacement will work on nearly any exhaust system with a similar spring.
- Made from stainless steel, and has a high temp silicon sleeve to protect exhaust component finish.
- Made by Akrapovic, 60mm size, SOLD EACH
New Body Plastics available in Black, White, Carbon Fiber, Dark Blue, or Yellow.
Also, Currently Exclusive to ProCycle: Olive Green, and Desert Sand (complete kit only)
Includes Rear Fender, Side Panels, Headlight Cover, and Front Fender.
Choose a Kit with Maier Front Fender [pic1] or after market SuperMoto Fender (black or white only) [pic2].
- SuperMoto fender kit includes our High Mount Fender Bracket!
The race-bred RS-2 exhaust has proven to be extremely popular among rider looks for a combination of performance and value. It enhances performance dramatically, provides an enviable exhaust note and offers the unmistakable look and sound of Yoshimura. RS-2 mufflers feature a straight baffle that leads to a single turn-down machined aluminum end cap.
All models have a USFS Approved spark arrester in a oval-shaped sleeve with a large volume of packing material.
Created as a championship-caliber trials tire, the D803 also delivers in a wide range of conditions, which makes it perfect for trail riding. Compliant carcass construction for excellent traction. Radial-design rear tire works great for off-road trail riding. This is a 4.00-18 rear tire. Traction is amazing and trail damage is minimized with the less aggressive pattern. If you have never tried a trials tire before, give it a whirl, you will be amazed. Not great in muddy conditions.
The B & B Eng. DRZ400 Bash Plate is made from 4mm thick 5083 aluminium plate. Strong and great looking, this is the top of the line protection plate for the DRZ. Supplied with all the necessary stainless steel clamps and bolts required. Available in polished or with the heavy-duty black polymer coating. Like all he other B&B Bash Plates, these plates have foam or rubber where required to keep things a bit more quiet. This plate fits the E, S, SM & kick start models.
CNC laser cut from 1/8" aluminum with a large 12.5" (length) x 10" (width) mounting surface area. Quick installation with a 4 point mounting system and no modifications required. There are integrated turn signal mounts, along with multiple strap slots for securing gear bags and cargo. All hardware and instructions are included.
The Rack is compatible with all RotoPax mounts.
You may purchase the rack alone, or you can order the Rack with the RotoPax.
The TAPP™ is a compact, easy to mount, all weather 2.1amp USB Power Port and is the answer for powering and charging your USB devices including cell phones, smart phones, most GPS units, MP3 players, and most digital cameras.
Quick charge 3.0 technology provides fast charging for Android devices with Quick charge capability. Charging power levels up to 18 watts contrast with the USB standard maximum charge power of 10 watts.
TAPP™ 2.1 Amp Weatherproof USB Power Port With Quick Charge 3.0 Technology
- Input Voltage: 12V ± 4.0V
- USB (Output) Voltage: 5V ±.25V
- Output Current: 2.1A Max
- Output Current Quick Charge: 18 watts Max
- Maximum charge rate for all USB phones and tablets including iPhone, iPad and Android tablets
- Cable length: 6ft (2M)
- Enhanced electrostatic discharge damage (ESD) resistance
Galfer USA produces several different brake pad compounds for all types of riding styles and uses. With over 60 years of friction material production and research, they have learned that one compound doesn’t always do the trick across the board. If you are just looking for an OEM brake pad replacement or a high performance race brake pad, they have you covered!
Set includes front and rear brake pads.
Semi-Metallic Compound
OEM replacement upgrade. Great feel, long lasting, and very little rotor wear with this durable compound. Compound applications for almost every need, including off road, street, touring, enduro, dual sport and more. Precision made in our Galfer factory in Spain.
Our most popular compound! This compound is the work horse of the Galfer family and is a great OEM upgrade for the everyday rider.
The Nomadic Rack for the early generation KLR650. CNC laser cut from 3/16" 5052 aluminum with a large 12" x 18" mounting surface area. Sand blasted and then powder coated black to give it a shot peened look. This rack is an easy installation with no modifications required. There are multiple strap slots for securing gear bags and cargo. Rack is compatible with RotoPax mount. All hardware and instructions included.
Packages available include Rack with the RotoPax Mount or if you really want it all, you can order the Rack, Mount and a Fuel or Water Container.
The Q4 employs intricate chambers, baffles and proprietary multistage packing material making it the best performing quiet muffler available.
Constructed from aircraft grade aluminum and high strength stainless steel.
Sound output 96dB. Several pounds lighter than the stock muffler.
All in one package.
- Hot Rods complete +4mm stroker crank assembly
- 94mm big bore cylinder and piston kit
- Complete gasket set with seals
- Includes new crank bearings
We suggest adding a set of HotCams camshafts and a new clutch kit for the best results.
These Twin Air Dual-Stage air filters deliver unbeatable performance and protection which is why they are the hands-down choice of more world and national champions than all other filters combined. Twin Air's fused layers of open-pore foam and fine inner foam trap even the smallest particles without restricting airflow. This filter kit includes a new air filter cage.
Their rear racks are great for adding the extra storage needed for your next adventure. They are the perfect size for a backpack or small duffel bag. Their steel racks are built to handle any riding style you throw at them, now Rotopax ready!
This is the ENDURO Series TW200 rear rack which measures 10 inches wide and 12 inches long.
Easy to Install
- Works great for mounting Pelican and Seahorse cases, or any other hard case. Givi compatible.
- Holes are in place to accept Rotopax mount with no drilling required.
- Instructions included, uses stock hardware.
- Fabricated with mild steel, MIG welded, and finished with a semi gloss black industrial grade powder coat.
- Weighs 3 lbs, 10 inches wide, 12 inches long.
- Works with stock tool bag. You can remove the seat with no interference from the luggage rack.
- Rear rack only, no Rotopax mount or side racks included.
- Ready for your 1 gallon Rotopax can and mount
- 1.75 gallon Rotopax fuel can is not recommended with this rack
Sized perfectly for adult back-yard racing or fast/aggressive mini riders. This is the most important upgrade you can make for an adult sized rider. The stock suspension is too soft for most adults and aggressive kids. Fits stock shock.
- 30% stiffer than stock
- Preset and stress relieved for long life
- Custom wound from aircraft quality spring steel
- Powder coated finish
- Our own #190 cam profile offers more lift to give better low-end and mid-range punch and more duration to keep the motor pulling hard in the upper RPMs.
- Our performance cams are reground from OEM camshafts - no core charge or return required.
- We recommend a high compression or big bore piston to get the most out of your performance camshaft.
We strongly recommend checking valve to piston clearance when installing a non-standard camshaft.
These great grip pads give you that improved relationship between you and your machine. You will feel the difference the minute you throw your leg over. Squeeze your tank and feel what a solid seat position is and does for you. They will assist in reduction of vibration, increase in control, and increase in comfort.
Will also help you cover wear spots on your tank whether it be the stock metal or a plastic tank. We tested had a couple sets of these on bikes with plastic tanks for at least 3 years and saw no signs of bubbling, peeling or coming off in any way.
Stock suspension suffers from poor compression damping and limp rebound damping. The Race Tech Gold Valve allows you to tune both compression and rebound valving for vastly improved performance.
- Bolt-on shock valving for serious suspension performance
- Improves control, traction, plushness and bottoming resistance
- Improved, long-wearing, low-friction sealing design decreases fade
- Includes complete instructions
So you say you want more light for your dual sport? Give this 7"DOT legal Rally light a try and light it up like a freight train! HIGH/LOW operation and SAE/DOT/E4 approved.
This light does not have the large Cyclops logos shown on one of the images.
- Race Inspired Design
- Hella reflector, made in Germany stamped SAE/E4
- Lightweight Aluminum Frame
- Plug and Play for Bikes with H4 Bulbs.
- Available with optional mounting plate for computer or GPS
- Easily converted to HID if desired, uses an H4 bulb
- For bikes that are not H4 (XR650R), a simple H4 plug available at any auto parts store will allow you to use this light.
- Now the panel on top of the light for mounting speedos/gps's etc is included, (This is a platform, not actual GPS mount.)
Optional 10.0 Lumen LED High/Low Upgrade and now the Phoenix LED complete headlight for the ultimate DOT headlight
The stock lamp that comes with this rally light is great, but you can get well over double the brightness with the LED upgrade at a substantially lower power draw. Note if your bike is ac powered at the headlight you will need the rectifier for the LED option.. AKA carbureted KTM's CRFX and XR400/650.. others may apply.
CNC machined from 5mm aluminum 5083 plate with lots of slots to attach your Rok Straps (or other straps). This gives a considerably wider deck than the standard B&B Rack. Attaches directly to the B&B rack with four screws that are included. Available in either polished aluminum or a black polymer coating.
These plates are pre-drilled and countersunk from the bottom making installation of a RotoPax mount quick and easy.
Some older carry racks will not have predrilled holes in them to mount luggage plate in which it will require you to drill yourself (select pre2018 version)
This is for the add -on Top Plate only.
Fits B&B Luggage Rack purchased AFTER 2018
More range at a great price.
The 3.6 gallon tank is for the off-road DRZ400 and DRZ400E.
The 3.9 gallon tank for the dual-sport DRZ400S. The 3.9 gal tank also fits the ES and SM models.
Both tanks are available in a selection of colors.
NOTE: Clarke tanks do not come with a vent hose or vent cap.
An upright Dakar Rally inspired shield designed to protect the rider without interfering with off-road riding. For on-road riding the Rally shield protects the rider’s core from fatiguing air blasts while keeping the head in clean air. Duck behind it in the cold or the rain to keep from experiencing the brunt of the elements. During off-road riding the Rally windshield protects the rider from any amount of mud, dust, roots, rocks, or branches without becoming invasive. Whether standing on the pegs or ducking behind it, you will be impressed at the protection it offers.
The Rally shield for the TW200 is 13 inches tall, 12.5 inches wide at the bottom, 9 inches wide at the top, and made from military grade 1/8 inch cast acrylic in either clear or tint.
The RS-4 Slip-On exhaust has a unique design that provides an unrivaled combination of power and a quiet exhaust note.
- Pentagonal-shaped sleeve
- Front muffler cap functions as a polyresonant chamber which helps reduce noise
- Laser-cut heat shield on polyresonant chamber
- Two-stage stepped baffle
- Turn-out carbon fiber end-cap
- Stainless steel tail-pipe
Cogent Dynamics Mojave product is a drop-in replacement for the DR650 stock shock, no modifications necessary. Mojave is not simply an improved Suzuki shock, it is a brand new replacement shock that is a totally engineered suspension solution to suit your needs.
Each shock is assembled and tested on the Cogent Dynamics suspension dyno before being packed up and shipped. Like its bigger brother the Mojave Pro Series, this will make an incredible difference in the handling of your DR.
Mojave Improvements over stock
Mojave upper mount: uses a precision spherical bearing with dust seals, which accurately transfers damping forces to the motorcycle frame.
Internal improvements: Cogent designed shaft, seal head, damper piston, adjuster and clevis.
Mono tube construction: precision honed, super-stiff steel body with an upper body cap machined from billet aluminum.
Built-in billet aluminum separator piston provides an in-line gas pressure reservoir which eliminates the Suzuki rubber bladder.
This shock package includes the CNC machined Bling Ring Preload Adjuster Collar and Preload Bearing that will make preload adjustments easy.
Select the spring you want installed based on the load you plan to carry. For riders (and gear) less than 250 pounds we recommend the 7.6 kg/mm spring. If you regularly have more than 250 pounds the bike, you might want to use the 8.15 kg/mm spring. If you have any questions at all about this, please call.
You may choose to add the Hydraulic Preload Adjuster to make it the easiest of all. All you do is twist the knob. Includes mounting bracket for knob unit. (Some CA carb compliant models may need slight modification for mounting the preload adjuster.)
Low shock also available. This option will lower your seat height 1" without the need for lowering links. All other features of this shock are the same as the stock height.
Need to remove your clutch assembly? This holder is the quickest and easiest tool out there to get a grip on that hard to handle hub. Laser cut to the exact pattern that EBC makes their clutch plates from, it makes loosening and re-tightening the clutch nut easy. All of that and no worries about doing any damage to your expensive clutch hub.
This kit combines common wide platform Yamaha YZ/WR foot pegs with brackets that are custom made to fit the TW200. If you are tired of standing on the stock skinny footpegs, get yourself a set of these fat boys and have pegs that match the tires on your T-Dub! For ultimate comfort, order the Pivot Pegz kit!
Simply unbolt your stock brackets and bolt these in their place. The bracket on the right side (brake lever side) is shorter than stock to correct the offset in the stock pegs. On kickstart models, the stroke of the kickstart lever is shortened slightly. Should you ever need to replace the pegs in the future, simply order pegs for the Yamaha YZ or WR 250/450.