Search Products

The POV harness is the ultimate integration of wearable video camera mounts utilizing a backpack harness system. The POV harness easily integrates with any CONFIGUR8 pack system via the unique ladder lock system allowing you to catch hours of video footage without the need for any additional straps or mounts. Simply attach the camera to the universal camera mount turn it on and launch. No more mucking around, the chest mount is easily accessible for set up and offers one of the most immersive perspectives for action sport footage.

When your done taking footage you can remove the POV harness and interchange it with any other CONFIGR8 system or simply revert back to a standard configuration backpack in less than a minute. The universal design of the POV mount allows for an endless range of options. The great thing about this design is that it's super flexible—only your imagination sets the limits! If you're thinking about hitting the trails at night, whether it’s planned or spontaneous, you can easily adjust the mount to work with lighting systems.

Stock size rear brake rotor laser-cut from high-carbon content 410 stainless steel, then lap cross hatched and heat-treated. Each one then has a high-temp paint applied to surfaces like cooling holes and edges for a clean finished look.

Includes a fresh set of brake rotor bolts.

These tips are for the Warp 9 Shift Levers only. 

These are held to the cast Warp 9 lever with a pin and e-clip making them easy to change out. Includes new pin and e-clip in case you lose yours.

You can also order just a new pin hardware kit which comes with new pin and clip.

 Warp 9's CNC shark fin rear rotor protector. To make installation super-easy this fin bolts to a brand new CNC machined caliper bracket. Just remove your existing caliper bracket and remove the pins, install them on this new one and then put the caliper and fin back on.

The starter bushing in the DR650 leads a tough life. Exhaust heat and minimal lube from the factory take their toll. Warp 9 has a high quality solution - a billet starter cover with a sealed ball bearing.

• CNC machined starter endcap
• Black anodized for good looks
• High Speed Abec 3 double sealed roller bearing installed
• Reduced amperage needed to start bike
• Brushes will have extended life

Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a plusher ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.

These great features combine to offer you a custom seat feel, and provide greater enjoyment and increased range for long commutes, or Dual-Sport rides!

The Complete Seats come assembled with an aftermarket pan and ready to ride.

Quality replacement front fender from Maier.

A digital voltmeter that can be mounted almost anywhere, on any bike, thanks to ProCycle's multi-position stainless steel bracket. Keeps you informed on the status of your charging system.

Completely waterproof and comes with connectors, wires and thorough instructions. A "must have" device for riders who use heated riding gear, heated grips, additional lighting, GPS, etc.

The Recon S-3 has been designed for intermediate distance rides and is a mid sized pack. The Recon has the flexibility of free load storage space on the outside with increased internal storage above the smaller Sprint R-3. This pack also has a large outer pocket that can hold the Zac Speed tool roll (not supplied) when not used with the optional Matrix Tool Pack. Like the Sprint, the Recon pack is made from durable 1680D Poly fabric to ensure it meets the demands of the tough off-road environment with high quality YBS zips. With three compartment pockets, one internal soft lined goggle pocket and two external technical pockets the Recon has ample storage options for trail rides.

The Recon comes standard with high quality Source 3 Lt/100oz bladder system with a quick connect hose system. The Recon pack has been designed with a wide vented TPR waist belt system to keep the pack stabilized whilst offering optimal comfort and ventilation. The pack is also equipped with the Zac Speed CONFIGR8 pack system allowing you to customize your pack with other CONFIGR8 elements for superior flexibility and adaptability.

The Sprint Enduro backpack has been purposely designed for short fast competition rides with its minimal design and aggressive graphics. The Sprint R-3 is a fourth generation pack that adopts the NEW CONFIGR8 adaptive pack harness system. In keeping with tradition the Sprint is a low profile design to minimize lateral and vertical movement. To optimize comfort and stability we have used a vented TPR waist belt system with enhanced padding profiles for improved ventilation.

A 3L hydration system provides ample water storage whilst offering 3 individual compartments with two deep sidewall pockets for maximum flexibility. A wide aperture main compartment access allows for quick easy bladder installation. The Sprint also comes with a removable pack shield to improve protection and maintain the ventilation structure of the pack. The back panel-padding uses a Bio-foam design for improved comfort and easy access to the pack ladder lock system and pack shield compartment. 

Cogent Dynamics Mojave product is a drop-in replacement for the DR650 stock shock, no modifications necessary. Mojave is not simply an improved Suzuki shock, it is a brand new replacement shock that is a totally engineered suspension solution to suit your needs.

Each shock is assembled and tested on the Cogent Dynamics suspension dyno before being packed up and shipped. Like its bigger brother the Mojave Pro Series, this will make an incredible difference in the handling of your DR.

Mojave Improvements over stock
Mojave upper mount: uses a precision spherical bearing with dust seals, which accurately transfers damping forces to the motorcycle frame.

Internal improvements: Cogent designed shaft, seal head, damper piston, adjuster and clevis.
Mono tube construction: precision honed, super-stiff steel body with an upper body cap machined from billet aluminum.
Built-in billet aluminum separator piston provides an in-line gas pressure reservoir which eliminates the Suzuki rubber bladder.

This shock package includes the CNC machined Bling Ring Preload Adjuster Collar and Preload Bearing that will make preload adjustments easy.

Select the spring you want installed based on the load you plan to carry. For riders (and gear) less than 250 pounds we recommend the 7.6 kg/mm spring. If you regularly have more than 250 pounds the bike, you might want to use the 8.15 kg/mm spring. If you have any questions at all about this, please call.

You may choose to add the Hydraulic Preload Adjuster to make it the easiest of all. All you do is twist the knob. Includes mounting bracket for knob unit. (Some CA carb compliant models may need slight modification for mounting the preload adjuster.)

Low shock also available. This option will lower your seat height 1" without the need for lowering links. All other features of this shock are the same as the stock height.

This DOT kit includes LED headlight assembly with plug-and-play wiring harness, a specially designed adjustable steel mounting bracket, and all the required installation hardware.

No cutting, no drilling, no wiring modifications! Installation takes 5 minutes.

This kit is highly recommend over the non-DOT kit. The low beam has extra punch and a proper beam pattern cut-off. The high beam throws light far and wide. It’s already a crowd favorite!

Two colors to choose from, Chrome or Black. Light output and beam pattern are the same for either color.

• Low Beam: 20W, 2,800 Lumens
• High Beam: 35W, 3,600 Lumens
• Color Temperature: 6,000k
• DOT & SAE Compliant
• CE, RoHS, ISO9002, IP67

Your choice of an aluminum bolt-on foot pad or a steel weld-on unit. Each will make the footprint of the stock side stand considerably larger, preventing your DR from tipping over in soft terrain. The bolt-on unit is cut from aluminum and then powder coated black, it comes with stainless steel mounting hardware.

The bolt-on pad and does require use of a drill for installation. The weld-on pad will need to be welded to the stand and then the entire unit painted for corrosion protection.

Stamped from heavy gauge stainless steel, Giant Loop® Mounts bolt onto virtually any motorcycle, snowmobile, snow bike, ATV, UTV, SxS, 4×4—and even boats. These mounts help keep straps away from hot exhaust while shortening strap lengths for maximum stability and helps make installation of Giant Loop Saddlebags, Panniers, Dry Bags, and Tank Bags even easier. 

Sold as a set of two (2).

• DIMENSIONS: 2.5″ L x 1.75″ W (64 cm L x 44 cm W) Hole: 0.39” (10 mm)
• MATERIALS: Stamped heavy gauge stainless steel.

Made with heat-treated carbon steel for longer wear life and reduced galling.

This Waterproof First Aid Kit is the perfect size for your "Don't leave home without it" list.

Always keep your first aid kit handy and right where you left it. The Waterproof First Aid Kit easily mounts almost anywhere you need it with self-adhesive hook-and-loop mounts. Contents stored in a heavy-duty nylon bag, with waterproof zipper and special coating to ensure your supplies stay dry.

• Sintered Pads are best for regular riding. Long life, and good performance in all conditions 
• Sport Carbon pads are made for fast riding in dry conditions. Not recommended for mud, water, or sand 
• Race Sintered are designed for racing use only; not for street use

Includes front and rear brake pads

The PowerBomb header promotes better flow by allowing a small expansion of the exhaust gasses. The 'bomb' also acts as a pre-muffler taking the edge off of overall sound levels. Includes clamp-on mounts for the stock heat shield.

For FMF mufflers only

Givi makes a great set of Crash Bars available for the Africa Twin. If your intentions include off-road riding of any kind, you really should not go without protection. Not only for you, but for your bike too. Even a slow-speed tip-over can cause damage that would make riding away impossible.

Your first choice is whether you would prefer black powder coated steel or Stainless Steel. Both are built from 25 mm diameter material welded to steel mounting plates. Select the lower set based on your color of choice and whether or not you have a standard transmission or a DCT transmission. You must select the correct model in order to ensure correct fitment. These provide protection for the engine and surrounding components. These units do NOT require the upper guards and work great on their own.

Included with each piece you receive a complete set of instructions and all mounting hardware required, in typical Givi fashion.

Please Note that these Crash Bars are also compatible with the Givi Skid Plate.

• EBC Double H Sintered pads feature the HH friction rating - the highest in the industry. Provides maximum brake effect and lasts twice as long as organic pads.
• Organic Base made with high-performance aramid fibers. Provide excellent stopping power without noise and rotor galling, even on polished rotors. Fingertip control and strong, predictable brake response

Pirelli's Corsa radial or bias-ply with maximum grip tread.

Superb corning and straight-line stability.

Exceptional wet-weather performance.

Tubless design.

Each kit includes all necessary rubber components and brake pins.

Hand built aluminum luggage rack from the B&B Off Road Engineering folks down under. This unit really is a beauty to look at and extremely rugged, made from 4mm 5083 aluminum plate! Tie down whatever you need with confidence. Whether it's your books to get to school or a bag to get across the country, no worries mate. Available in either bare polished aluminum or with a black polymer coating.

While plenty rugged to use as grab handles, you can keep your stock handles if you so desire. All necessary stainless clamps and bolts are provided.

If you want a wider platform for support, consider adding the luggage plate to this rack.

  Bike must have the DR250 Taillight installed to work with this rack.It will not work with the stock USA taillight.

Stock chain guard crack and crumble on you? Won't happen to this unit CNC machined from 2.5mm marine grade aluminum. Polished to a beautiful sheen that will give your DR that little twinkle as well as better protection.

Sintered Pads from EBC provide great performance in all conditions yet still give you long pad life. Front pads are double H rated for maximum breaking. Rear shoes offer maximum durability and excellent braking performance.

Droppin’ into the weather? Combine Bushwackers Hand Guards with rigid hand guards/deflectors and heated grips for the ultimate protection against the elements. Ride safer and longer with warm, dry and clean hands and controls. Essential gear for motorcycles, snow bikes and snowmobiles.

• Cold/wet weather comfort
• Brush, mud and trail protection
• Strap on/off in seconds
• Multiple mounting configurations to fit most motorcycle makes/models equipped with rigid hand guards and/or deflectors
• Tough stretch polyurethane strap (can be used separately)
• Custom wind foil shapes
• No stitching or pieces to fail
• When not using Bushwackers Hand Guards, straps have a thousand other uses: Lash water bottles, fuel, gear to tail rack. Hold flashlight in place while working in dark. And many others!
• Made in USA

REQUIRED EQUIPMENT: Motorcycle must be equipped with rigid hand guards or deflectors to support Bushwackers while riding.

Materials: Corona (UV) Treated, Matte Finish, .055 Gauge Polyethylene Plastic
Dimensions (flat): 13.5″ (length from end closest to bar clamp to end closest to bar end) x 16″ (widest part at end of bars) x 6″ (narrowest part nearest center of bar)

This LED headlight from JNS Engineering is DOT approved and an entirely new LED specific headlight! A specially designed adjustable steel mounting bracket replaces the stock unit. Included is a wiring harness and all the required hardware to make this installation quick and easy and mostly plug and play. The DOT kit does not have a daytime running light (parking light) and may require minor trimming on the backside of the fairing. The headlight features separate low and high beam projectors in a custom headlight shell designed specifically for this LED bulb. The primary advantage of this kit over the original is the DOT/SAE markings and a wider high beam pattern.

Low Beam: 30W, 2,800 Lumens
High Beam: 50W, 3,600 Lumens
Color Temperature: 6,000k
DOT & SAE Compliant
CE, RoHS, ISO9002, IP67

EBC brake pads contain aramid fibers; these are man-made high-performance fibers used widely for their light weight, high strength, abrasion resistance and thermal stability.

This kit is not just a bulb, but an entirely new LED specific headlight! A specially designed adjustable steel mounting bracket replaces the stock unit. Included is a wiring harness and all the required hardware to make this installation quick and easy and entirely plug and play. No cutting, no drilling, no wiring modifications are necessary. The headlight features separate low and high beam projectors in a custom headlight shell designed specifically for this LED bulb.

This kit is available with either a chrome or black chrome reflector in the headlight.

Does not fit '87 TW200 because that year has a unique AC powered headlight circuit.

This CNC cap will replace the stock gas cap on the stock tank. You do need some parts from the stock cap, so don't throw it away yet! It is not difficult and this kit includes the additional hardware required. Also included is a vent tube with a matching cap.

For use on STOCK TANK ONLY! This is NOT a locking cap.
Does not fit California model DR650

The jet kit for riders who want their bike to run well but do not want to modify the air box.

The Ti ProKit w/Titanium needle adds more power and better throttle response. Easy to install and tune - no slide drilling. No air box modification.

Includes: a main jet selection, adjustable titanium needle, clips (with extras), pilot jet, instructions.

The genuine factory shop service and repair manual. This is the reference manual Yamaha dealers use in their service departments. It has all the necessary info to do any maintenance or repairs to your WR250R or X.

The MotoPressor is a compact pump unit that weighs only 1.3 pounds and fits in the palm of your hand! Measures 4"x3"x1.5"  This makes it smaller and easier to carry with you.

It includes a 8 inch long inflation hose, with a a low air loss chuck. You also get an SAE power cord that attaches to your battery and stays there, along with alligator clips with SAE connector. The Pocket Pump has an 6.5 foot power cord. All of this packs into a heavy duty neoprene pouch.

MotoPressor will inflate a 150/70/ R18 tire from 0-31psi in under 4 minutes, and is capable of pumping up to 130psi. It also features a built-in cooling fan to keep the pump at optimum operating temperature, and a check valve to check the psi by attaching your tire gauge to this valve.

E3 Resistor Spark Plugs

• Unique electrode shape maximizes the power created by the spark plug – Diamond Fire technology
• Electrode is a combination of performance and technology that results in an improved flame kernel shape
• This flame front ignites the bulk air/fuel mixture faster, moves heat into the combustion chamber faster and creates a more localized pressure front for faster pressure rise during the cylinder power stroke
• The result is more complete combustion and an improvement in engine performance
• A truly premium performance plug
• Sold individually, unless otherwise stated.

Keep your motor running right with fresh spark plugs!

NGK is one of the world's largest manufacturer of spark plugs, whose products are used as original equipment (OE) on countless motorcycle and automobile models.

• High-quality materials and superior construction for serious power and reliability
  • Pure alumina silicate ceramic insulator provides high strength and better heat transfer
  • Deep-seated copper core for a wider heat range
  • Nickel alloy tip for longer life
  • Trivalent metal plating provides superior anti-corrosion and anti-seizing properties
• Choosing the right high-quality plugs prevents fouling from running too cool and preignition from running too hot
• NGK plugs available for almost every application and riding style

Ever had to turn back on the trail because of downed limbs? Or have you ever been moto camping and needed some wood for a fire?

This is the tool for you then! We have tried this manual chainsaw and it makes quick work of hard woods like Oak.

The chain itself is 25 inches long with 8 inch nylon straps at each end. All together this saw weighs 1/4 of a pound. This will tuck away nicely into any tool pouch or saddle bag as it roll up into a tight round.

Rear wheel bearing kit. Includes a new dust seal and the bearing and seal for the cush drive hub. All bearings are sealed on both sides.

This is a great Dual-Sport tire from Dunlop. Designed for the true 50/50 rider. An Adventure product for the price-conscious customer. Full tread depth pattern designed for rigorous off-road use yields excellent traction on everything from hard-packed fire roads to soft single-track trails. Versatile tire performance allows riders to travel on the street and venture off-road. A tire equipped to go anywhere, the D605 is a value option for the all-around rider. DOT approved.

Folding tip, forged aluminum shift lever from BBR Motorsports. Stronger and lighter than the stock shift lever.

• Bolts directly to the shift shaft, eliminating the need for the stock linkage which can get sticky and is prone to collecting mud
• Strong forged aluminum construction
• Steel knurled folding tip (chrome plated)
• Anodized titanium finish
• 1" longer than stock

This Motion Pro press tool is a must have when installing and removing Clip-Style master links (520, 525 & 530 sizes).

Easily presses on and off master link plates, works on 520, 525 & 530 Clip-Style master links.

Maximum master link width 24.8mm.

Will not damage master links, hardened steel pins for reliable use.

Light weight billet aluminum construction.

Here is the little switch that mounts inside your brake or clutch lever perch and controls the brake light or clutch safety circuit. This switch often gets damaged in an unplanned dismount (aka: crash) or the plastic simply cracks from age. When this happens, you can find yourself chasing a short circuit that keeps blowing your fuse every time the brakes are applied. If this has happened to your TW, here's the fix!

Iridium spark plugs are made with premium quality materials.

Iridium plugs last longer than standard ones, meaning you won't have to replace them as often.

• The ultimate in the evolution of spark plug technology and performance from an industry leader
• The iridium electrode is 25% smaller than a platinum electrode, and it's just 1/4 the size of a conventional nickel electrode
• Ultra-small diameter center electrode reduces voltage requirement and extends ignition system life
• Metal shell plating has enhanced anti corrosion qualities

Sold individually, unless otherwise stated.

From Barnett, the number one name in motorcycle clutches since 1948, we now offer a complete high performance clutch set. This includes Kevlar friction plates, steel drive plates and stronger springs.

The Cogent Dynamics DDC valves are the most cost-effective upgrade you can make to your motorcycle’s forks. Unique and the first of its kind, a DDC kit is available to upgrade many motorcycles that are originally equipped with simple damper rod type forks as front suspension.

We do recommend stiffer than stock front springs to bring the full potential of the DDCs out. Up to about 200 pounds (rider with gear on) we recommend the .85 kg/mm springs. If you are above 200 pounds (rider with gear on) you should probably go with the 1.0 kg/mm springs.

Evans Waterless Coolant (EWC) can be used for all water cooled motorcycles to eliminate overheating. With a boiling point in excess of 375° F, it will not vaporize, thus eliminating overheating, boil-over and after-boil. At the other end of the spectrum, EWC freezes below -40° F.

EWC also delivers more power by eliminating pre-ignition and detonation caused by overheating, thus improving combustion efficiency. It also generates very low vapor pressures which reduces strain on cooling system components. EWC comes in 1/2 gal. containers.

  Installation requires specific procedures. Please refer to the instructions.

Included in this kit are the parts needed to repair a second generation TK carburetor. You get a new float bowl gasket, needle valve with O-ring, needle, mixture screw, and stock jets for the '01-'21 models kits.

The Speedo DRD corrects and fixes the speed signal after it was altered by something else, such as sprocket changes or tires size changes or transmission changes.

• Smallest electronic speedometer/odometer calibration device in the world
• Simple plug-in installation
• Weather proof design to protect against the elements

Have you already ditched the bulky tail light on your XR? Don't want to bend your license plate and wrap it around your rear fender? Here is a great solution to clean up the looks of the backside of your XR650L. If you haven't already upgraded to the smaller and better looking WPS Tail light, select 'Bracket & Light' from the menu and you will get the WPS Taillight AND the License Plate Holder.

Please note that this no longer has a window for a license plate light. To stay legal, you can mount one or two License Plate Lights to your plate holder, or you can check out the LED License Plate Frame.

The Edge-2 Tail Light and License Plate Holder is a simple bolt-on replacement for the stock unit. Included is an aluminum mount for the light and license plate that is model specific. The light unit uses 16 high-intensity red LED's for tail / stop light function. 3 white LED's are used for license plate illumination.

Included is a set of turn signal brackets that bolt to the mount, but these are designed for a smaller LED type signal with a mounting stud of just 8mm. If you think this might be a problem, look at the Edge-2 Upgrade Circuit Board as this converts your brake light into a functioning turn signal as well!

NOTE: LED's must be installed on a 12 V DC system!

The Speedo DRD corrects and fixes the speed signal after it was altered by something else, such as sprocket changes or tires size changes or transmission changes.

The Universal Kit does require some basic wiring to install. It's fairly easy, and only 4 wires; [positive, ground, signal-in, signal-out]. Universal Kit works for Cars, Trucks, & Motorcycles with digital odometers, and 3 wire speed sensors.

• Smallest electronic speedometer/odometer calibration device in the world
• Simple plug-in installation
• Weather proof design to protect against the elements

Dynojet Jet Kits increase power and smoothness throughout the entire rev range, while maintaining optimum fuel economy. Each Dynojet Jet Kit includes comprehensive instructions which show step-by-step installation and testing procedures to ensure a perfect setup every time.

• Stage 1: stock engine/filters, stock/modified pipes; about a 5% power increase
• Increases power and drivability
• Fully adjustable

A fresh set of brake rotor bolts. These bolts already have thread lock compound applied to the threads.

Stock OEM works with factory rotors, comes in a pack of 6.

For aftermarket rotors like Warp 9 or EBC front and rear sets are available.

Front comes in pack of 6
Rear comes in pack of 4.

 The perfect option for the DIY'er.

The Cogent Dynamics Shock Shaft Assembly is ready for installation. The Cogent shock shaft also features an external rebound damping adjustment. Just what you need to have the ultimate in rear suspension control.

Does not include a spring. Compatible with both stock and aftermarket springs.

Requires 5wt shock oil

Good News: There’s finally a plug & play LED headlight conversion kit for your 2008-2020 WR250R and WR250X!

This kit includes a sealed LED headlight assembly with plug & play electrical connection, adjustable powder coated steel mounting bracket set, and mounting hardware. 

Installation is a five minute, one beer exercise. If you can change a residential light bulb you will have no problem installing this conversion kit. We promise.

Please note that you will need to reuse your OEM upper headlight mounting grommet and two aim adjustment springs.  Or add new ones to freshen up your whole headlight unit.

Low Beam: 2,100 Lumens, 20 Watts
High Beam: 2,800 Lumens, 30 Watts
Operating Voltage: 10V-30V DC
Color Temp: 6,000K
Lifespan: >50,000 hours

Twin Air's patented design, high quality materials and superior construction deliver unbeatable performance and protection - and make Twin Air Filters the hands-down choice of more World and National Champions than all other filters combined.

Twin Air's fused layers of open-pore foam and fine inner foam trap even the smallest particles-without restricting airflow!

Reduce exhaust leaks with this new OEM muffler gasket. This gasket goes between the rear tail/muffler pipe and the header pipe.

These versatile Risers allow you to clamp a 7/8" diameter handlebar or you can remove the 7/8" reducers and then clamp an 1- 1/8" aluminum "fatbar". If you are thinking of going to a fatbar after you bend your stock set or just want the versatility and option to run any bar, this is the riser to go with. Reducers lock into risers to insure no slippage between components.

These risers use 8mm bolts. Always check and confirm that your bike has adequate cable and brake line length before installing any handlebar risers.

Anti-Vibration Risers may interfere with aftermarket large capacity fuel tanks, and some steering stem clamp configurations (in these cases we recommend using standard pivoting risers).

This filter is meant for 5/16" fuel lines. Only 1/2" thick it is small enough to fit just about anywhere.

Warp 9’s Pro Rim Locks are developed with Ice Track, Dirt Track and Flat Track Racers in mind!

Burnt Titanium Main Bolt

Lightweight Forged Aluminum Body

Black 7075 T6 Tower Nut and Base Washer

Base washer is machined to match each specific rim curvature for a perfect fit

About half the weight of OEM rim locks!

1.60 front  – 1.8 oz

1.85 front – 2.0 oz

2.15 rear – 2.3 oz

2.50 rear – 2.7 0z

3.00 rear – 3.10 oz

Mount Barkbusters standard aluminum bar handguards to 1-1/8" motorcycle handlebars with the Barkbusters Tapered handlebar saddle clamp set.

What's in the box:

• 4 peice saddle clamp set
• 2 complete saddles

These are all you need to mount your current Barkbusters Handguards when you upgrade to a tapered oversized 1 1/8" handlebar.

An ADV tire designed in Australia for real off-road riding. Technically 25% stronger than many adventure tires with a tread deeper than most and a compound formulated to perform in a wide variety of conditions. The tread design on this tire is unique in that the blocks self-sharpen for better grip through the life of the tire.

If you want the best in traction, wear and dependability, try a set of Tractionator ADV Rear with Dual Venture Front. All sets now have Dual Venture Front with ADV Rear.

NOTE: All of the sizes listed are Tubeless Tires (unless otherwise noted) and can be used as such with tubeless certified wheels. Tubes can be run in Tubeless tires, but a Tube Type tire cannot be run Tubeless.

The Mikuni TM42-6 HSR flows 17CFM more than the TM40-6 and incorporates many upgraded features such as a roller-bearing slide.

All this means going even faster has never been so easy, say goodbye to hard starting, hesitations and flat spots.

A new high output stator for the XR650L. 25% more output than the stock unit. Approximately 50 additional watts. Now you can have enough power to run those driving lights and/or heated riding gear!

Twin Air Filter's patented design, high quality materials and superior construction deliver unbeatable performance and protection - and make Twin Air Filters the hands-down choice of more World and National Champions than all other filters combined.
An air filter is your engine's only protection against the elements, and your stock filter isn't up to the task. Replace it with a Twin Air- the number 1 filter system proven on motocross tracks around the world.
Twin Air's fused layers of open-pore foam and fine inner foam trap even the smallest particles-without restricting airflow

• Complete set of friction plates, steel plates, and springs
• Heavy-duty springs help prevent clutch slip
• Restores proper stack height, fixes clutch slip caused by wear and tear

To fit tapered 28.5mm (1 1/8") handlebar.

• Barkbusters strongest handguard EVER!
• Designed for Enduro and Trail bikes.
• Two mounting points secure the full wrap around aluminum design.
• Compact curved profile to protect hands and levers during intense trail and tight bush riding.
• Heat treated aluminum backbone for maximum strength.
• Replaceable, high impact resistant EGO plastic guards included.
• Large range of colors matched to popular motorcycle brands.
• Deflectors available for increased protection (sold separate).
• Easy installation.
• Note: Not ideal for bikes with long clutch and brake levers.

NOTE: will not fit Renthal Twin Wall or Barkbusters VSBar.

This is a high-quality seat cover done by Moose for the DRZ400. This is a replacement cover only, no seat foam and you must install on your existing pan with existing foam. Heavy-duty marine grade vinyl with UV protection for long life. Double stitched for durability too!

Throttle, Clutch or Speedo cables.

Corbin seats are carefully designed to provide a comfortable riding position. They are firm and supportive which allows you to ride all day without fatigue unlike the stock seat. Comfort Cell Foam retains resilience and doesn't crush down like the stock seat foam.  On the top, Corbin covers are only the highest grade of weather resistant materials for durability and long life.  Corbin seats install the same as similar to stock with two bolts into the chassis which provides a closer fit to the bodywork and tank.

Recover that shredded or uniquely colored stock seat cover with this OEM black cover. This includes only the cover material (grab strap is no longer available). Designed to fit over your stock seat pan and foam.

Air filled AirHawk 12"x18" cushion custom fits your shape and redistributes pressure that causes numbness and discomfort when you ride. Seat cushion cover is constructed of a breathable, stretchable Nylon/Lycra blend with a non skid Urethane base. Open mesh side panels allow heat to escape. Easily inflates by mouth with no pump needed. Mounting straps and Repair patch kit included.

Seat Concepts dual-sport/adventure seat-kits incorporate a wider seating area for the rider, which results in more even weight distribution, while reducing pressure points. Each kit contains detailed instructions for easy "Do It Yourself" installation. This provides the highest level of quality & comfort at an affordable price. Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable! Available as a Foam and Cover Kit for OEM pan. It DOES NOT include the pan.

Corbin seats are carefully designed to provide a comfortable riding position. They are firm and supportive which allows you to ride all day without fatigue unlike the stock seat. Comfort Cell Foam retains resilience and doesn't crush down like the stock seat foam.  On the top, Corbin covers are only the highest grade of weather resistant materials for durability and long life. Corbin seats install the same as similar to stock with two bolts into the chassis which provides a closer fit to the bodywork and tank.

Corbin seats are carefully designed to provide a comfortable riding position. They are firm and supportive which allows you to ride all day without fatigue unlike the stock seat. Comfort Cell Foam retains resilience and doesn't crush down like the stock seat foam.  On the top, Corbin covers are only the highest grade of weather resistant materials for durability and long life. Corbin seats install the same as similar to stock with two bolts into the chassis which provides a closer fit to the bodywork and tank.

Corbin seats are carefully designed to provide a comfortable riding position. They are firm and supportive which allows you to ride all day without fatigue unlike the stock seat. Comfort Cell Foam retains resilience and doesn't crush down like the stock seat foam.  On the top, Corbin covers are only the highest grade of weather resistant materials for durability and long life. Corbin seats install the same as similar to stock with two bolts into the chassis which provides a closer fit to the bodywork and tank.

Corbin seats are carefully designed to provide a comfortable riding position. They are firm and supportive which allows you to ride all day without fatigue unlike the stock seat. Comfort Cell Foam retains resilience and doesn't crush down like the stock seat foam.  On the top, Corbin covers are only the highest grade of weather resistant materials for durability and long life. Corbin seats install the same as similar to stock with two bolts into the chassis which provides a closer fit to the bodywork and tank.

Corbin seats are carefully designed to provide a comfortable riding position. They are firm and supportive which allows you to ride all day without fatigue unlike the stock seat. Comfort Cell Foam retains resilience and doesn't crush down like the stock seat foam. On top, Corbin covers are only the highest grade of weather resistant materials for durability and long life. Corbin seats install the same as sock seats using the two bolts into the chassis, which provides a closer fit to the bodywork and tank.

Corbin seats are carefully designed to provide a comfortable riding position. They are firm and supportive which allows you to ride all day without fatigue unlike the stock seat. Comfort Cell Foam retains resilience and doesn't crush down like the stock seat foam. On the top, Corbin covers are only the highest grade of weather resistant materials for durability and long life. Corbin seats install the same as similar to stock with two bolts into the chassis which provides a closer fit to the bodywork and tank.

Here's the Moose Racing seat for you XR650L riders. This is a complete seat that's installed on a new seat pan. Take your old seat off and put your new seat on and get back to riding! The durable micro-fiber suede top cover enhances rider comfort and increases stability. Side gripper panels ensure secure seating during aggressive maneuvers. The cover is constructed from smooth marine-grade vinyl and features an embossed Moose Racing logo. It includes a strap kit that enables secure attachment of cargo to the pillion section of the seat.

Corbin seats are carefully designed to provide a comfortable riding position. They are firm and supportive which allows you to ride all day without fatigue unlike the stock seat. Comfort Cell Foam retains resilience and doesn't crush down like the stock seat foam.  On the top, Corbin covers are only the highest grade of weather resistant materials for durability and long life. Corbin seats install the same as stock with two bolts into the chassis which provides a closer fit to the bodywork and tank.

This is a high-quality seat cover kit by Moose for the XR650L. This is a direct replacement seat cover only. No seat foam, and you install on your stock pan with existing foam. Heavy duty marine grade vinyl, and UV protected for long life. Double stitched for durability. Available in Red or Blue.

Made in the USA                                                                                                                              

Corbin seats are carefully designed to provide a comfortable riding position. They are firm and supportive which allows you to ride all day without fatigue unlike the stock seat. Comfort Cell Foam retains resilience and doesn't crush down like the stock seat foam.  On the top, Corbin covers are only the highest grade of weather resistant materials for durability and long life. Corbin seats install the same as similar to stock with two bolts into the chassis which provides a closer fit to the bodywork and tank.

Corbin seats are carefully designed to provide a comfortable riding position. They are firm and supportive which allows you to ride all day without fatigue unlike the stock seat. Comfort Cell Foam retains resilience and doesn't crush down like the stock seat foam. On the top, Corbin covers are only the highest grade of weather resistant materials for durability and long life. Corbin seats install the same as stock with two bolts into the chassis which provides a closer fit to the bodywork and tank.

Designed for use with stock engines using either stock or aftermarket exhaust and air filters.

• Provides a simple and affordable solution to carburetor tuning problems.
• Allows you to tune your bike for increased power and smoothness while retaining fuel economy.
• Includes a guide booklet on how to install and use your jet kit to its full potential.

Make the installation as easy as possible with this Optional Connector Set. This allows you to put an OEM style connector on the Edge Taillight Circuit Board Upgrade making the connection simple. Stock plug will go right into this unit and off you go. You will need a crimp tool or set of needle nose pliers to crimp connectors on.

RotoPax are Rotational Molded - the process which produces indisputably superior products.

• Thicker walls and stronger construction
• Bright colors that are less prone to fading
• Extra threads, thicker walls, and sure-seal gasket guarantee no leaks

Need to mount two containers? A water and a fuel? Two waters? Finally, you can stack multiple packs together! Use in conjunction with a pack mount. You will need to purchase the Single Mount as well as the Extender.

RotoPax holder made to mount a single Fuel and/or Water container.

Need to mount two containers? A water and a fuel? Two waters? Get the extender which allows you to stack two containers no problem! Single mount, two containers

Parabellum LTD. has continued the highly demanded Rally Shield line by fitting up the 1993-present Honda XR650L. This is an upright Dakar Rally inspired shield, designed to protect the rider without interfering with off-road riding. For on-road riding the Rally shield protects the rider’s chest from fatiguing air blasts while keeping the head in clean air. Duck behind it in the cold or the rain to keep from experiencing the brunt of the elements. During off-road riding the Rally windshield protects the rider from mud, dust, roots, rocks, or branches without becoming invasive. Whether standing on the pegs or ducking behind it, you will be impressed at the protection it offers. Their Rally shields have been tested in the toughest conditions including an entire SORCS hare scramble season.

*The Rally shield for the XR650L is 12.5 inches tall 12.5 inches wide at the bottom and 8.5 inches wide at the top and is made from military grade 1/8 inch cast acrylic.

The correct spring rate for your weight will give a smoother more controlled ride. No more bottoming and better traction and confidence off-road. Kit includes required adapter collars

Stock Shock Spring 7.28 kg/mm

*Spring color may vary due to specification requirement and availability.

This adapter set is required to fit an aftermarket spring to the Vstrom shock

Race Tech HP Springs have a high stiffness-to-mass ratio. In other words; the springs are light weight for their particular spring rate. This requires the finest materials and processing. Shot-peened and pre-set so they cannot sack out. All Race Tech HP Springs have the highest rate tolerances in the industry. These are the finest springs in the world-guaranteed.

OEM spring rate is 6.7kg/mm. We offer stiffer spring rates for riders who wish to carry luggage or just prefer stiffer suspension.

Race Tech shock springs require adapter collars which are included with your spring. *Spring color may vary due to specification requirement and availability.

DRZ400 E/S

A pair of Race Tech fork springs to dial in your front suspension to suit your weight.

Fits all DRZ400 models with conventional forks (not for SM)

Recommended spring rates:

Gasket for the engine case cover over the clutch. Doing any clutch work, you probably want to replace this gasket so you don't have any leaks when you are all done with the project.

For the frame drain on your XR650L ,extra protection for your motor! Strong magnet at the end of the plug picks up metallic flakes in your oil, protecting your engine!

PSR dual sport mirrors come with a slightly convex mirror for a wider field of vision behind you. The round mirror is 4.25" in diameter while the oval is 3.75" x 3". These mirrors are easily adjustable and fold out of the way quickly with the 1" RAM mounts.

The RAM Ball Stud Base used for both mirrors will go into any standard 10x1.25 threaded mirror base.

Sold individually. 

 All Yamaha's will need a mirror adapter if you have the stock perch.

All the parts you need to freshen up your brake master cylinder. New piston, seals, return spring, boot and snap ring.

Made by Nissin, an OEM supplier in Japan

Seal profile is engineered to create equal pressure in each seal lip; equalized seal pressure creates less drag and longer seal life.

Patented MAX-LIFE has a coefficient of friction up to 3 times less than the OEM seal material

Triple-lip seal design

Dyno-tested to last 3 to 4 times longer than OEM seals

Directional ribs allow seal to be installed easily

Kits include fork seals and dust wipers

• Race Tech's original bolt-on fork valving system for front cartridge forks
• Triple the flow area of stock pistons
• Put valving control on the shim stack
• Outstanding tunability; improved control, traction, plushness and bottoming resistance
• Complete instructions, Gold Valve pistons, valving charts, valving shims and "Technical Edge
• Fork Maintenance and Gold Valve Installation" video all included