This replacement lens has a clear panel on the bottom to illuminate your license plate.
Allows you to bolt your license plate directly to the rear fender.
Does not fit Australian DR650.
This device will pulse your brake light automatically. There are over 1000 possible pattern combinations with individually programmable Flash Speeds, Pre-Delay, and Flash Durations, as well as a disable feature to disable the unit. This device gives the end user the widest range of possibilities for customizing your tail light safety flash. With simple programming setup using only your brake lever, their is no disassembly or removing of the seat required to change the programming on the device.
Features:
There is a lot of technology packed into this tail light/fender eliminator kit. You have programmable turn signals and Safety Brake Pulsing both built into this product.
You can enable or disable the safety brake pulsing feature.
This kit includes only the highest quality components, including the pre-installed 12oClockLabs processor board, which is made in the USA.
We recommend a "Fixed Rate Flasher" unit for use with this kit. When you install aftermarket signals it changes the load on a factory signal system.
This kit does not include parts to mount aftermarket turn signals. The pre-installed processor board allows the turn signals to be integrated in to the tail light.
Use these brackets to mount your light weight auxillary lights or turn signals. They will bolt directly on to the DR650 lower triple clamp bolts. This makes for a clean 'tucked in' installation. Sold in pairs.
Replace these any time you feel excessive play in the sprocket hub.
Excessively worn dampers can cause the cush hub bearing to fail - which will ruin your sprocket carrier.
Sold as a full set.
Replace these any time you feel excessive play in the sprocket hub.
Excessively worn dampers can cause the cush hub bearing to fail - which will ruin your sprocket carrier.
Sold as a full set.
Here is the little switch that mounts inside your brake or clutch lever perch and controls the brake light or clutch safety circuit. This switch often gets damaged in an unplanned dismount (aka: crash) or the plastic simply cracks from age. When this happens, you can find yourself chasing a short circuit that keeps blowing your fuse every time the brakes are applied. If this has happened to your TW, here's the fix!
Add a backup kick start system to your electric start DRZ400. Complete with everything you need to add the kick starter to your bike.
This kit will fit all DRZ400s but the manual decompression lever can only be installed on the 2006 to Current DRZ400 E models.
CNC machined oil filler cap with locking clip to keep it in place in the roughest conditions. The cap is pre-drilled and the locking clip is safety wired to the mounting tap with a section of silicon tubing, that will not melt or discolor, over the wire. First class all the way. Available in Silver, Black, Blue or Red.
Replace your worn clutch plates and springs to reduce fade and slip.
E3 Resistor Spark Plugs
The unique design of the electrode maximizes the power generated by the spark plug through Diamond Fire technology. This electrode combines advanced performance capabilities and innovative technology to enhance the shape of the flame kernel. Consequently, the flame front ignites the air/fuel mixture more rapidly, accelerates heat transfer into the combustion chamber, and creates a more concentrated pressure front, facilitating a quicker pressure rise during the cylinder power stroke. The outcome is a more efficient combustion process and improved engine performance, making this a truly premium spark plug.
Keep your motor running right with a fresh plug.
A Dual Electrode spark plug will last longer than a single electrode plug because the wear is shared between the electrodes.
Iridium spark plugs are made with premium quality materials.
Iridium plugs last longer than standard ones, meaning you won't have to replace them as often.
Sold individually, unless otherwise stated.
This is all you need to not only change your oil, but protect your motor as well. We include a magnetic drain plug in the standard kit, to help catch stray metal pieces, a 5-pack of oil filters, and new O-Rings to replace any you have that may be leaking or worn.
Standard kit includes:
A complete set of gaskets, o-rings and oil seals. Everything you will need when doing a complete engine re-assembly.
Genuine Suzuki OEM o-ring for your crankshaft access engine plug.
All in one package.
We suggest adding a set of HotCams camshafts and a new clutch kit for the best results.
Stage 1 - Excellent mid-range and top-end power increase.
Uses stock valve springs and rockers.
Does not incorporate compression release.
New wider seat to help keep comfortable on that long commute or dual sport ride. The added width and foam density will help keep the seat from being an item to stop you from going on that ride or enjoying the bike.
The new updated 2.0 version has a sleeker shape and a better fit in the tank area.
Complete Seats come assembled on an aftermarket pan and ready to ride.
| Width: | 9 1/8" (232mm) |
| Height: | 1" (25mm) Lower than stock |
These wider seats from Seat Concepts help keep you comfortable on those long commutes or dual sport rides. The added width and improved foam density help keep your seat from being the item to stop you from going on those big rides or enjoying the bike.
The Complete Seats come fully assembled on an aftermarket seat pan, and are ready to install and ride.
| Width: | 9.5" (241mm) |
| Height: | Same as OEM |
State-of-the-art replacement seats, Sargent seats are built on a percision-molded lightweight Polytec seat pan. Sargent's proprietary seat foam (Super Cell Atomic Foam) is their own unique blend of resilience, firmness, and vibration-absorption qualities, making it well suited for long distance comfort and support. Sargent seats are covered in a marine-grade, UV-stablized mildew resistant CarbonFX vinyl. Available in standard height and 1" lower than stock. These seats will fit bikes with the stock, IMS, or any other aftermarket fuel tank.
| Width: | 11" (279mm) |
| Height: | Same as OEM |
Most fuel injected systems are very lean in their stock configuration. This is good for economy and emissions, but not performance. This unit allows you to adjust the Fuel/Air (F/A) ratio without remapping the ECU and getting into complicated software programs. The PowerJet Fuel Controller allows you to adjust the fuel map from -4% to +10% by selecting one of 10 built-in settings (including stock).
The device works by measuring the outside air temperature very close to where the stock sensor is located and then adjusts the signal from the OEM air temperature sensor to the ECU to make use of the Air Temperature Correction factor that is built into the stock ECU. The ECU is told that the intake air is a little cooler than it actually is and it responds by richening the injection map very slightly. How much depends on your setting on the PowerJet. This will result in improved throttle response, especially if you have an aftermarket exhaust of any kind.
PowerJet is easily installed by plugging it in between the stock AIT sensor and the bike's wiring harness under the seat. This can be done very quickly as they are exactly the same plugs. Unplug the stock connection, plug in the PowerJet on each side. The PowerJet fits easily under the seat behind the battery as it is rugged and waterproof. PowerJet comes with a full one year warranty.
Twin Air Filter's patented design, high quality materials and superior construction deliver unbeatable performance and protection - and make Twin Air Filters the hands-down choice of more World and National Champions than all other filters combined.
The air filter is your engine's only protection against the elements, and your stock filter isn't up to the task. Replace it with a Twin Air-the #1 filter system proven on motocross tracks around the world.
Twin Air's fused layers of open-pore foam and fine inner foam trap even the smallest particles-without restricting airflow.
Are you a fan of K&N air filters? Here's one built just for the TW200. Top of line filtering to keep that engine healthy for years to come.
Twin Air Filter's patented design, high quality materials and superior construction deliver unbeatable performance and protection - and make Twin Air Filters the hands-down choice of more World and National Champions than all other filters combined.
An air filter is your engine's only protection against the elements, and your stock filter isn't up to the task. Replace it with a Twin Air- the number 1 filter system proven on motocross tracks around the world.
Twin Air's fused layers of open-pore foam and fine inner foam trap even the smallest particles-without restricting airflow
Repair leaking carburetor or worn out float needle assembly.
The Phillips screws in Japanese motorcycles are not really Phillips screws. They are actually Japanese Industrial Standard (JIS) screws that are very easy to strip with Phillips head drivers.
Greatly eases basic chain maintenance, tire changes, parking, cleaning, etc. All necessary hardware is included. Installs using basic hand tools. Tough black powder coated finish.
For riders who wish to run the centerstand and the lowered footpegs we recommend installing a Warp 9 brake pedal. The Warp 9 pedal is arched to give the necessary clearance under the pedal.
T-Rex stands are made from steel tubing finished in black powder for durability. Back by a 3-Year limited warranty for any material or manufacturing defects. Rest assured that you are getting best material commercially available.
Greatly eases basic chain maintenance, tire changes, parking, cleaning, etc. All necessary hardware is included. Installs using basic hand tools.
This is the gasket used between the header pipe and the stock muffler. This gasket is not needed for aftermarket mufflers!
Since Kawasaki brought back the popular little KLX250 with updated fuel injection, Yoshimura brought back an updated RS-2 slip-on that now incorporates an o2 sensor that accommodates the new fuel injection technology on the KLX. All of that with added power, torque and that distinct Yoshimura exhaust note.
Entire unit is proudly made in the good old US of A to boot!
The product that you are purchasing is designed and intended for closed course competition use only and is labeled as such, i.e. Yoshimura "RACE SERIES." Yoshimura RACE SERIES products are neither designed nor intended for use on PUBLIC ROADS or LAND. Such use is prohibited by Federal and State regulations.
Have you lost your stock heat shield, or need one on an aftermarket head pipe? FMF makes this nice unit that includes clamps, heat shield with the FMF logo and button head screws to hold it on. We recommend Anti-Seize on all exhaust fasteners.
This is a genuine Suzuki part. We recommend installing a countershaft seal retainer to prevent the countershaft seal from popping out while riding.
These springs are custom wound specifically for the XT225. Stiffer than the .36 kg/mm stock springs, these will make your front perform significantly better. Combine them with the Cogent DDC's and you will be very happy with the results. Sold as pairs.
DRZ400 E/S
A pair of Race Tech fork springs to dial in your front suspension to suit your weight.
Fits all DRZ400 models with conventional forks (not for SM)
Recommended spring rates:
| Rider Weight w/gear lbs. | Spring Rate |
|---|---|
| 90 or less | .42 |
| 90-119 | .44 (stock) |
| 120-150 | .46 |
| 150-180 | .48 |
| 180-220 | .50 |
| 220-250 | .52 |
| 250+ | .54 |
Bushings are dyno-tested to 500,000 strokes with less wear than OEM bushings
Kit includes all the fork bushings, o-rings, snap rings and washers. This kit comes with what you need to completely rebuild your front fork bushings.
Complete kit to replace the bearings and seals in the DR350 shock linkage. Includes the lower shock bearing.
| Kit Contents: | |
|---|---|
| Spherical Bearing | 1 |
| Snap Ring | 2 |
| Seal | 6 |
| Needle Bearing Shaft | 3 |
| Needle Bearing | 5 |
Complete kit to replace the bearings and seals in the DR650 shock linkage. Includes the lower shock bearing.
| Kit Contents: | |
|---|---|
| Seal | 8 |
| Needle Bearing Shaft | 4 |
| Needle Bearing | 6 |
Stock suspension suffers from poor compression damping and limp rebound damping. The Race Tech Gold Valve allows you to tune both compression and rebound valving for vastly improved performance.
Race Tech HP Springs have a high stiffness-to-mass ratio. In other words; the springs are light weight for their particular spring rate. This requires the finest materials and processing. Shot-peened and pre-set so they cannot sack out. All Race Tech HP Springs have the highest rate tolerances in the industry. These are the finest springs in the world-guaranteed.
This spring is 8.0kg/mm
OEM spring rates are 5.7-7.6kg/mm progressive style.
Damping Rod style forks are notorious for being too harsh, too mushy and too easy to bottom. Gold Valve Cartridge Emulators remedy this problem by controlling the compression damping with a tuneable valve. The Emulator sits on top of the damping rod and is held in place by the main spring.
Simply put; Emulators make damping rod forks perform like well-tuned cartridge forks. Installation and tuning for any condition or rider preference is very straight-forward.
Simple to install and completely tunable for all conditions and rider preferences.
*Comes with RaceTech adapter to properly seat the Gold Valve cartridge into to the top of the damper rod.
Provide protection for your motorcycle’s front brake and clutch levers with Barkbusters aluminum bar lever protection handguards. Model Specific, these guards feature heat treated full wrap aluminum backbones that mount at two points on each side for strength. Prevent costly damage to your motorcycle with Barkbusters aluminum bar lever protection handguards.
Features:
Add Plastic Handguards for a complete kit.
High quality aluminum caliper guards from Works Connection protects your brake caliper and looks great too.
Radiator guards from Devol Racing protect your radiators from damage due to trail side objects and roost bullets. They offer protection not just from frontal assaults but also from those tricky side attacks. Made from high-grade aluminum alloy for light weight and strength, these guards have an improved air-flow design that eliminates any overheating problem. A solid mounting to the frame make these stronger than most guards that just mount to the radiators themselves.
Devol Racing makes a super product that will keep you on the trail for a long time.
Need to remove your clutch assembly to get at that dreaded neutral safety switch? This holder is the quickest and easiest tool out there to get a grip on that hard to handle hub. Laser cut to the exact pattern that EBC makes their clutch plates from, it makes loosening and re-tightening the clutch nut easy. All of that and no worries about doing any damage to your expensive clutch hub.
Bottom line, if you have to hold your clutch hub to remove it, there is no better way to do it.
Need to remove your clutch assembly? This holder is the quickest and easiest tool out there to get a grip on that hard to handle hub. Laser cut to the exact pattern that EBC makes their clutch plates from, it makes loosening and re-tightening the clutch nut easy. All of that and no worries about doing any damage to your expensive clutch hub.
Designed to enhance the appearance of your motorcycle, yet provide greater riding distance per tankful. Larger capacity than stock, yet very slim and sleek. These tanks are made with POLYETHYLENE CROSSLINK for extra strength and durability.
Available in multiple color choices. Choose Natural if you wish to easily see the fuel level of your bike. 4.0 gallons.
Get better range from your DR650 by adding an IMS 4.9 gallon fuel tank. Available in Natural, White, Black and Blue. Natural color is recommended if you wish to easily see the fuel level in the tank. Includes cap and fuel petcock.
Get better range from your XR650L by adding a Clarke 4.7 gallon fuel tank. Cannot use stock shrouds.
Available in Natural, White, Black, and Red. Natural color is recommended if you wish to easily see the fuel level in the tank. Includes cap, uses stock petcock.
Get better range from your early KLR650 by adding an IMS 6.6 gallon fuel tank. The big tank also provides radiator protection.
Designed to enhance the appearance of your motorcycle, yet provide greater riding distance per tankful. Larger capacity than stock, yet very slim and sleek. Perfect for the dunes or the race track! These tanks are made with POLYETHYLENE CROSSLINK for extra strength and durability.
Natural color is recommended if you wish to easily see the fuel level in the tank.
This tank requires you to re-use your stock petcock valve. Does Not Use OEM/Stock Shrouds
If you need a replacement cap for your Acerbis tank, why not go bling? These caps have a carbon fiber pattern molded into them that is extremely realistic. Looks like the real thing. Topping off the cap is a CNC Machined metal vent cap. This eliminates the need for a lengthy vent tube that gets in the way. The vent cap allows air to vent into the tank but does not allow fuel to splash out during normal use or during a tip over.
These caps fit Acerbis tanks only.
If you're like us, you hate the long floppy vent hose hanging off the cap of your aftermarket tank.
This one-way vent cap replaces the long hose with a short one only about 2" long. It allows air into your tank but prevents fuel from sloshing out.
Machined from billet alloy and anodized for good looks.
Not for stock fuel tanks!
You’d be amazed at the dirt and debris that can work its way into your gas can – and from there, your fuel tank. Twin Air’s monofilament screen pocket inserts in your tank to catch particles as small as 40 microns (.00165”) while allowing the gas to flow freely.
The flange is custom-sized for each modern 4-stroke model to ensure a leak-proof seal. Just remove the filter periodically, turn it inside-out, and clean out the debris that could have been in your engine.
Will not work with factory locking gas caps.
Inside tank inlet diameter must be approximately 43.5mm (1.71") to fit.
The DR650 Air Scoop was designed to increase airflow to the oil cooler helping to prolong the service life of your motorcycle.
Does NOT work with Acerbis 6.6 gal tank.
New replacement side panels specifically made for gen 1 KLR650.
Available in 4 colors.
Will not fit KLR250
Depending on your application and preferences, more than one optional heat shield may be useful.
Quality windscreen made from Lucite aircraft acrylic making it more rigid and optically clearer than OEM windscreens
These models are 2"-4" shorter or 2"-4" taller than stock to meet your particular riding preference.
This is an upright Dakar Rally inspired shield designed to protect the rider without interfering with off-road riding. For on-road riding the Rally shield protects the rider’s chest from fatiguing air blasts while keeping the head in clean air. Duck behind it in the cold or the rain to keep from experiencing the brunt of the elements. During off-road riding the Rally windshield protects the rider from any amount of mud, dust, roots, rocks, or branches without becoming invasive. The Rally shield for the XT250 is 13 inches tall
11 inches wide at the bottom and 8.5 inches wide at the top. Made from military grade 1/8 inch Cast Acrylic, available in clear or tint.
ProCycle Plastics (formerly DSA) Rear Fenders include LED tail/brake light and license plate holder. Vacuum molded, these parts are a design improvement over stock.
Universal design. Vents in the back improve airflow to motor. Smaller front reduces 'wind steer' and improves high speed stability.
From Shinko Tires, the 705 Series are DOT approved Dual Sport tires designed for 75% street and 25% trail riding. A versatile tread pattern provides excellent wet and dry weather adhesion and the compound resists tearing while riding off-road. "R" in size denotes a radial tire.
This street-legal knobby from Pirelli has good stability and cornering precision thanks to the carcass stiffness. The tread pattern optimized for use on dirt and gravel roads, cross-country racing and desert tours. It has lasting off-road performance and knob tearing resistance due to the special off-road compound.
Dunlop designed the D606 tire to be street-legal but with an emphasis on aggressive off-road riding and great durability. A full-depth tread pattern designed for rigorous off-road use yields excellent traction on everything from hard-packed fire roads to soft single-track trails. At the same time, the D606's tread compound is engineered for good highway durability and grip.
The Dunlop D606 is R rated (max speed of 106 mph)
Dual Sport tube-type tires for the TW200 or the VanVan.
With its versatile tread pattern, the 428 makes an ideal OEM replacement.
Front tire is a 130/80-18 (66P load / speed rating) while the rear is a 180/80-14 (78P load / speed rating).
We offer two different types of SuperMoto tubes. The first are Standard Tubes and are meant to be used with standard bias-ply type tires, but can be used with radial tires also.
But, if you are running radial tires, like SuperMoto, or have a retro bikes with spoked wheels and radial tires, you probably want to run the 'Radial Tubes'. Front tubes fits 120/70 and 120/60 tires. Rear tubes fits 150/60, 150/70 and 160/60 tires. These have a metal valve stem.
A Radial tire specifically designed for small displacement sport bikes. Advanced belt design and Jointless Band (JLB) rear tire construction utilizes a continuously wound belt for smooth performance and a consistent tire contact patch. Aggressive sport-derived treat pattern for enhanced on-bike appearance.
These tires are all tubeless and H-rated (max speed of 130 mph)
This advanced filter oil & cleaner kit by No Toil is alcohol free, completely biodegradable and compatible with all foam filters.
A premium billet sprocket carrier from Warp 9 Racing that houses 2 bearings to help protect against the sideways twisting load that is commonly known to prematurely wear out the bearing and cush rubbers. This wear can cause extreme failure possibly damaging the hub.
Offered in anodized Silver or Black, Includes spacers and hardware.
These are designed to work with Warp 9 and OEM hubs.
Quality replacement clutch cable.
Replacement shift lever with folding tip.
Genuine Suzuki replacement brake and clutch levers. Standard length.
Available as a set or individual.
Please notice that this set is for '10-current DR650.
This bar kit will raise your hands 5.5" up from the factory riding position. If you are over 6 feet tall, this is the kit for you! It allows for a more natural riding position, no more bent neck and being hunched over the bars. You will be able to ride comfortably and more aggressively by installing this kit.
The ProTaper bars are taller and tapered from 1 1/8" to 7/8" and the braided stainless steel brake line will be a serious improvement to your braking ability. Braking becomes more responsive and firmer while adding a stylish look to your TW200.
Everything you need is in this kit to properly raise your bars:
Requires 7/8" factory bar clamps on bike
Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
Each kit includes all necessary rubber components and brake pins.
Innovative design makes tool easier and more secure to use than old fashioned pin-aligned drivers
This DR650 Oil Filter Guard is CNC machined from solid 6061 aluminum, black anodized, and then custom laser etched with our logo.
It fits over the fragile OEM magnesium cover and provides great impact protection in the event of a tip over. Proudly made in the USA.
A compact and lightweight solution to eliminate the SNAP for a safer tow. If you have ever towed a motorcycle you are familiar with the snap that comes with a traditional tow strap. GCAG made the Dynatow with a section that gives 32 inches of stretch so both riders have an easier tow.
The 26 foot total length gives you enough room to maneuver around obstacles and allows the freedom to choose better lines if you are towing in the gnar.
You can also use this as a recovery strap. You can girth hitch the loop end to the bike and throw the other end to a friend to pull. The dynamic properties of the Dynatow will help assist the pull. All of this functionality fits in a flat pouch about the size of sandwich and only weighs 12.8 oz. Throw it in your bag and be prepared.
Specifications:
Please consider the following before use: Practice before you need to use this product. Always inspect your Dynatow strap before use and NEVER use a worn strap. They recommend a proper training class to learn safe methods for towing a motorcycle.
The Chilly Exhaust Heat Shield is the most effective heat shield on the market. The innovative three piece design consists of a top shield attached to 2 rails with rivets and spacers. This reduces the contact area and slows down heat transfer. They have incorporated a patented, insulated reflective blanket on the underside of the shield to reduce radiant heat transfer. The included stainless steel clamp makes it simple to install.
We highly recommend a heat shield if you run soft luggage without hard racks.
FEATURES:
DIMENSIONS:
The Scramble Rack is optimized for carrying luggage on the sides. The side straps provide plenty of mount points and the spacing is MOLLE compatible. The top mounting surface on the Scramble Rack is minimal and designed for small packs.
There are two versions of this rack.
CONSTRUCTION FEATURES:
THINGS YOU SHOULD KNOW:
Patent Pending
Their rear racks are great for adding the extra storage needed for your next adventure. They are the perfect size for a backpack or small duffel bag. Their steel racks are built to handle any riding style you throw at them, now Rotopax ready! This is the ENDURO Series KLX250S/SF rear rack which measures 10 inches wide and 12 inches long.
Easy to Install
These top of the line Adventure pegs from Warp 9 are 5" long and 2.5" wide. They will give your feet the perfect perch whether you are cruising down the highway or standing up hammering down a singletrack trail.
New from Warp 9, top of the line Adventure Pegs. a full 5" long and 2.5" wide will give your feet the perfect perch whether you are cruising down the highway or standing up hammering down a single track trail.
NOTE: These pegs DO NOT fit the '18 model!
This kit combines common wide platform Yamaha YZ/WR foot pegs with brackets that are custom made to fit the TW200. If you are tired of standing on the stock skinny footpegs, get yourself a set of these fat boys and have pegs that match the tires on your T-Dub! For ultimate comfort, order the Pivot Pegz kit!
Simply unbolt your stock brackets and bolt these in their place. The bracket on the right side (brake lever side) is shorter than stock to correct the offset in the stock pegs. On kickstart models, the stroke of the kickstart lever is shortened slightly. Should you ever need to replace the pegs in the future, simply order pegs for the Yamaha YZ or WR 250/450.
Upgrade your Honda XR650L with a Subframe Brace Kit, designed to enhance strength and rigidity for your bike. This complete kit connects the frame and subframe, reinforcing the structure to support increased load capacity—perfect for riders using side cases, top cases, and rear racks.
Key Features:
High-Quality Materials: Attachment points are machined from 6061-T6 billet aluminum for superior strength and durability.. The 6.5mm thick support bars are laser-cut for a perfect fit.
Easy Installation: No cutting, drilling, welding, or modifications required for installation. Easy 20 min installation.
Enhanced Load Capacity: Provides added rigidity and support to the subframe, improving bike stability when carrying additional gear.
Exhaust Compatibility: Compatible with both STOCK Exhaust and FMF Exhaust systems.
Chain guards experience degradation over time as a result of chain friction. To ensure optimal performance replace worn components with genuine Honda parts.
This Super Siphon has a (1/2 inch x 6 foot) long hose, which makes it quite easy to transfer fuel from one bike to another! Simply, shake the hose to prime it and get fuel moving. The hose is resistant to gasoline and any other hazardous chemicals. Roll it up, stuff it in your bag and you will be very happy whenever you need it.
A complete kit to mount your phone (or other electronic device) to your motorcycle. The universal cradle expands from 2.25" to 3.25" wide and 4.75" to 6.25" tall. The width is adjustable but fixed while the upper portion of the cradle is spring loaded to keep your device secured in the roughest conditions.
Select the mount option that works best for you. The mirror mount is shown in the photo at left and is a flat plate with an 11mm hole on one side and a RAM ball on the other. Simply remove your mirror, place the plate between your mirror and the perch and tighten it down.
The handlebar mount kit allows you to mount to either a 7/8" or 1-1/8" bar. Also includes hardware to mount to the back of a lever perch. See image at bottom middle for kit pieces.
The X-Grip with handlebar mount is best suited for larger phones up to 4.5" wide. The spring loaded X-Grip cradle expands and contracts, allowing for a perfect custom fit. Kit also includes a device tether recommended for outdoor applications.
RotoPax holder made to mount a single Fuel and/or Water container.
This unique design adds strength and provides extra tightening power.
Use with included base plate or remove plate to attach mount direct by bolting up through the bottom or down through the top.
