Search Products

The FMF Powerbomb and Q4 Muffler are legendary in the exhaust market.

The Powerbomb header promotes better flow by allowing a small expansion of the exhaust gasses improving scavenging. The 'bomb' also acts as a pre-muffler taking the edge off of overall sound levels.

The Q4 muffler employs intricate chambers, baffles and proprietary multistage packing material making it the best performing quiet muffler available with a sound output of 96dB; with most models below 93 dB. It is constructed from aircraft grade aluminum and high strength stainless steel.

Have you lost your stock heat shield, or need one on an aftermarket head pipe? FMF makes this nice unit that includes clamps, heat shield with the FMF logo and button head screws to hold it on. We recommend Anti-Seize on all exhaust fasteners.

The Powercore 4 spark arrestor muffler. FMF developed the Powercore 4 to increase the horsepower and torque throughout the entire power curve. Highest quality packing for long life. Removable spark arrestor included. Louder than the Q4. Approximately 99db stock or about 94db with optional Quiet Insert installed.

• Uses long-life muffler packing for increased packing life
• Forest Service approved spark arrester

• The latest EVOLUTION of the popular LV ONE: aggressive sound and style
• Clean laser-etched Leo Vince logo in an innovative carved design (for the carbon fiber exhaust: bright aluminum die-cut high-temp resistant Leo Vince adhesive logo)
• Asymmetric design and high-tempiresistant full-carbon fiber end cap
• Impact-resistant sandblasted oval AISI 304 stainless steel sleeve – titanium look
• TIG-welded stainless steel front cup
• Adjustable full-carbon fastening strap
• Removable dB killer, weight savings and flawless installation

These hand-crafted bash plates from B&B Eng. are constructed from 4mm 5083 aluminium plate. Strong and lightweight, this material has been selected because of its extreme suitability for welding, abrasion and impact resistance. All the necessary stainless clamps and bolts are included. Plate has a polished finish with foam or rubber where required.

• Made from strong and lightweight aircraft aluminum
• Protects vital engine parts from rocks and debris
• Custom fit to your specific bike model
• Oil drain hole for easy access
• All mounting hardware included

These plates are made from 4mm thick 5083 aluminum because the extreme abrasion and impact resistance for the full weight of the bike and the rider. The front portion of the B&B Skid Plate bolts to mounts that are permanently attached to the forward motor mount. This means no more trying to hold clamps in place when you take you skid plate off for oil changes or cleaning. Easy off, easy on. All necessary hardware is included in the kit. The plate has foam or rubber wherever there is contact with the frame.

Choose from a polished finish or a black polymer coating.

Enjoy maximum protection and durability with an SW-MOTECH skid plate. Fully welded aluminum construction is engineered in Germany to provide proper protection from impacts, abrasions and projectile debris. Multiple ventilation slots on the front, sides and bottom of the skid plate permit maximum air-flow to keep your motor cool. Drilling, cutting, welding or any other permanent modifications are not required.

Features:

• Debris and collision protection for the engine 
• Fully welded 4mm thick aluminum plate / black side made of 2.5mm thick aluminum
• Efficient underbody protection of stone-chipping and collision
• Provides protection for the vulnerable oil pan & lower engine cases
• 100% bolt-on, no drilling, cutting, or any other permanent modifications needed
• Ventilated design maximizes air-flow to prevent overheating
• Silver
• Designed & engineered in Germany

What's in the box:

• SW-MOTECH skid plate engine guard
• Mounting hardware 
• Installation instructions

The X-Grip is a frame guard that allows the rider to both protect the frame of the motorcycle from wear as well as adding more grip to the bike.

Made from a dual injected mold; The outer plastic is durable polycarbonate while the inner plastic is durable yet playable and offers incredible grip.

Available in 2 colors

The SW-MOTECH Rear Brake Master Cylinder Guard is designed to fit the Yamaha Tenere 700. This guard protects the rear master cylinder from impact and prevents the foot from contact. A laser-cut and precision bent aluminum strengthening process makes the construction tough and durable and capable of withstanding heavier blows.

Features:

• Prevents contact between boot and foot brake cylinder and provides additional protection
• Lasered and bended from high-strenght aluminum.
• Brushed silver finish
• Easy Installation

Provide protection for your motorcycle’s front brake and clutch levers with Barkbusters aluminum bar lever protection handguards. Designed specifically for the Tenere 700, these guards feature heat treated full wrap aluminum backbones that mount at two points on each side for strength. Prevent costly damage to your motorcycle with Barkbusters aluminum bar lever protection handguards.

Features:

• Two mounting points provide secure protection
• Full wrap guards
• Heat treated aluminum backbone bars
• Easy installation
• Compatible with all Barkbusters deflector guards (not included)

Add Plastic Handguards for a complete kit.

Adventure bike heaven is off-road headed down a dirt road or a trail. If that is your dream, then as you know, you are going to fall. Sometime, someplace, it will happen, so be prepared! Save your bike before it happens.

SW-Motech makes some of the finest protection equipment available. The set-up for the Twin is available in a standard black powder coating or a semi-polished Stainless-Steel tubing. Both sets will protect the vital components of your motorcycle as well as you from damage incurred during a fall, slide or crash. They will preserve the frame, radiator, bodywork and other critical components from touching down with robust tubular steel. The black kit uses 27/21 mm tubing while the Stainless uses straight 22 mm tubing throughout.

Both configurations have a tight fit for great ground clearance and are designed to work seamlessly with other SW-Motech products like their Skid Plate/Engine Guard and SW-Motech Hawk light mounts. Three secure mounting points per side provide the necessary support that make these so strong. There is no drilling, cutting, welding or any other modifications required for mounting but still allows access to the oil filler, tool box and battery. Kit includes all necessary hardware and instructions and an aluminum cover to replace the OEM plastic cover at the lower mounting point on the left side.

Please Note that these Crash Bars are also compatible with the SW-Motech Skid Plate and the SW-Motech Centerstand.

This is all you need to not only change your oil, but protect your motor as well. We include a magnetic drain plug, to help catch stray metal pieces, a 5-pack of oil filters, and new O-Rings to replace any you have that may be leaking or worn.

• Magnetic Drain Plug
• O-Ring Kit
• 5-Pack of Oil Filters

This is all you need to not only change your oil, but protect your motor as well. We include a magnetic drain plug, to help catch stray metal pieces, a 5-pack of oil filters, and new O-Rings to replace any you have that may be leaking or worn.

• Magnetic Drain Plug
• O-Ring Kit
• 5-Pack of Oil Filters

This is all you need to not only change your oil, but protect your motor as well. We include a magnetic drain plug in the standard kit, to help catch stray metal pieces, a 5-pack of oil filters, and new O-Rings to replace any you have that may be leaking or worn.

If you need a new clutch, you probably need a new gasket to seal that cover when you are all done. Genuine Yamaha part.

Top End Gasket Set is designed for a piston replacement job and includes:

• Head Gasket
• Base Gasket
• Intake Gasket
• Exhaust Gasket

DRC is one of the leading manufacturers of silicone hose kits for motorcycles.

• Durable silicone radiator hose for dirt bikes
• Available for MX, ED racers and street dirt bikes
• Smooth inner diameter allows for increased coolant flow
• Printed white DRC logo. Available in red or blue colors

E3 Resistor Spark Plugs

The unique design of the electrode maximizes the power generated by the spark plug through Diamond Fire technology. This electrode combines advanced performance capabilities and innovative technology to enhance the shape of the flame kernel. Consequently, the flame front ignites the air/fuel mixture more rapidly, accelerates heat transfer into the combustion chamber, and creates a more concentrated pressure front, facilitating a quicker pressure rise during the cylinder power stroke. The outcome is a more efficient combustion process and improved engine performance, making this a truly premium spark plug.

Heavy-duty springs help prevent clutch slip in high-performance motors.

• Custom wound from chrome-silicon wire
• Preset for long life
• Higher spring seat pressure to resist clutch slip

Complete set of friction plates, HD springs and steel separator plates prevent premature driven plate wear, oil muddying and loss of stack height. Built with swaged aluminum carriers that spread the load on the clutch basket and prevent clutch basket "dogging". Anti-swell, alloy impregnated heavy-duty cork-based facings for smooth clutch take-up. Allows modulation, unlike paper clutches which tend to snatch.

Yamaha XT250 heavy duty chain guard.  

Made from 3/16" laser cut steel protects stock to oversized rear sprockets.  

This unique design bolts in the OEM location but rests against the rear axle bearing spacer for massive impact resistance.  

We have worked closely with Magura to come up with a kit that fits properly.

Want an easier pull on your DR clutch? No cable to break? Then say hello to the Magura Hymec Hydraulic Clutch. Simply remove the stock perch, lever and cable in bolt this in its place. This system replaces the stock cable with a small lightweight hydraulic system for improved clutch control, easier operating pressure, a constant pressure point and smoother actuation.

Developed over many years and tested under the toughest conditions possible in the off-road motorcycle world. World champions to novices all agree on the benefits of the Hymec Hydraulic Clutch system. Due to demand, Magura is now making this available for many dual-sport motorcycles, and now the DR650!

Never hurts to have a bit of the Margura specific Blood Red hydraulic fluid sitting on your shop bench. 4 oz. bottle available as an option.

These tips are for the Warp 9 Shift Levers only. 

These are held to the cast Warp 9 lever with a pin and e-clip making them easy to change out. Includes new pin and e-clip in case you lose yours.

You can also order just a new pin hardware kit which comes with new pin and clip.

These versatile Risers allow you to clamp a 7/8" diameter handlebar or you can remove the 7/8" reducers and then clamp an 1- 1/8" aluminum "fatbar". If you are thinking of going to a fatbar after you bend your stock set or just want the versatility and option to run any bar, this is the riser to go with. Reducers lock into risers to insure no slippage between components.

These risers use 8mm bolts. Always check and confirm that your bike has adequate cable and brake line length before installing any handlebar risers.

Anti-Vibration Risers may interfere with aftermarket large capacity fuel tanks, and some steering stem clamp configurations (in these cases we recommend using standard pivoting risers).

Quality replacement clutch cable.

• Nylon-lined housings and precise OEM component dimensions

This adapter will give you more mirror choices.

Yamaha mirrors have reverse threads on the right (throttle) side of the handlebars. This adapter allows you to mount a mirror with standard 10mm threads on the right side of your handlebar. This opens up many options for your mirrors, choose any 10mm mirror for your Yamaha.

• Torque spec: 5 Nm

This anodized billet piece, brings a touch of color to your bike. Available in red or blue, it replaces the stamped steel clevis that connects your brake pedal to the master cylinder.

Upgrade your Honda XR650L with a Subframe Brace Kit, designed to enhance strength and rigidity for your bike. This complete kit connects the frame and subframe, reinforcing the structure to support increased load capacity—perfect for riders using side cases, top cases, and rear racks.

Key Features:

• High-Quality Materials: Attachment points are machined from 6061-T6 billet aluminum for superior strength and durability.. The 6.5mm thick support bars are laser-cut for a perfect fit.

• Easy Installation: No cutting, drilling, welding, or modifications required for installation. Easy 20 min installation.

• Enhanced Load Capacity: Provides added rigidity and support to the subframe, improving bike stability when carrying additional gear.

• Exhaust Compatibility: Compatible with both STOCK Exhaust and FMF Exhaust systems.

2 high-quality bushings per set. They recommend changing bushings every 40 hours or at least once a year to get the best performance out of a set. If you are on an Adventure Bike and are doing a lot of road miles they recommend swapping out bushings once a year to ensure that you get the most vibration dampening of the bushings.

Every new set of pegs comes with a 90A bushing installed. This is a medium flex rating. 
80A is the softest and 95A lock-out is the stiffest and has the least amount of flex.

The bushings act like the suspension on your bike. With bushings, there are a couple of things to think about. The more firm the bushing the more durable and longer it will last. They use a durometer, a hardness scale 0 being the softest and 100 being the hardest. They don't go below a80 because they found that durability isn't great below this but have tested as low as a60 bushings. A bigger person that rides enduro-style terrain might want an a96 or a98 rated bushing. A lighter person might want the opposite but in the end, it comes down to personal preference. 

The bushings are high quality yet inexpensive (they achieve this because they use skateboard bushings that are already developed and produced in massive quantities around the world) and a wear item designed to be replaced each season or depending on how hard or often someone rides.  

For use on Motion Factory Foot Pegs Only

Made from 1/8" thick stainless steel with dual folded edges for additional strength, these brackets will relocate your passenger pegs down 4" and move them back 1.5". This will give your passenger additional legroom making two-up riding much more comfortable.

All hardware is included for a quick and easy installation.

Our complete foot peg assemblies. 1-3/4" lower than stock. No extra brackets that hang down below the frame. Easier on the knees. Wider platform Yamaha YZ style footpegs are stronger and give you firmer footing. Mount solid to the frame. No more 'droopy' feeling when standing on the stock pegs. Lowering your footpegs makes it easier to stand and less of a reach down to the bars when standing.

Now you can get our Low Pegs with MK4 Pivot Pegz or black Fastway ADV pegs (both Yamaha YZ pegs) installed!

This kit combines common wide platform Yamaha YZ/WR foot pegs with brackets that are custom made to fit the TW200. If you are tired of standing on the stock skinny footpegs, get yourself a set of these fat boys and have pegs that match the tires on your T-Dub! For ultimate comfort, order the Pivot Pegz kit!

Simply unbolt your stock brackets and bolt these in their place. The bracket on the right side (brake lever side) is shorter than stock to correct the offset in the stock pegs. On kickstart models, the stroke of the kickstart lever is shortened slightly. Should you ever need to replace the pegs in the future, simply order pegs for the Yamaha YZ or WR 250/450.

This is the ultimate adventure bike platform, it measures 2.25" wide, 4.75" long.

Patented adjustable collars make it easy to run them in the stock or lowered positions on most bikes.

Gain more room for bulky boots, or for longer legs. Fastway Adventure pegs come with two sets of F3 cleats, one standard, one long. Kamber bolts lets you adjust the 'tilt' of your pegs to increase comfort, or to give better squeeze on your bike.

Kit includes required fit kit.

Low peg mounts from JNS Engineering. You can use your stock pegs or aftermarket pegs with these T7 mounts.

These offer a 24mm drop & 24mm rearward offset.

Note: Not compatible with any center stand.

Pivot Pegz have set a new standard in footpeg performance and quality and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty. Pivot Pegz aim is to build the best footpegs in the world and they really do perform as good as they look. Here's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever!

• Wider, lighter, stronger design
• Widest (mm) and lightest pivoting pegs on the market
• Upgraded heavy duty, long life springs
• Unique multi-directional grip pattern
• Outstanding build quality
• Expanded motorcycle fitment range
• Overhaul kit includes: 2 pivot bushings, 2 pivot tension springs, 2 lock nuts, 2 washers, 6 o-rings, 2 split pins and instructions

The SW-MOTECH center stand for your Yamaha Tenere 700 increases the versatility of your machine for more secure parking on various terrain while enhancing ease of maintenance. Robust steel construction provides sturdy support for the motorcycle and is powder coated black for enhanced durability and corrosion resistance. This high quality center stand is designed and engineered in Germany for seamless integration with the factory original components and easy operation utilizing a built in foot lever which increases leverage and decreases lifting effort.

Features:

• Robust steel construction
• Attractive powder coated black finish adds corrosion resistance & durability
• Improves parking stability and versatility on various surfaces
• Significantly reduces the risk of a tip over when used on softer terrain vs side stand
• Integrates perfectly with the factory original components
• Easy to use German design uses leverage to make lifting a cinch
• Foot lever increases leverage to aid in lifting technique
• Does not require cutting, drilling or any other permanent modifications
• Allows on the road maintenance without a paddock stand
• Eases chain and tire maintenance
• Double retention spring ensures safe operation even if one spring fails

High quality steel sprockets.

Stock Gearing: 15/48-128x128

Quality Steel Rear Sprocket

Features:

• Aluminum air valve cap
• Comes in pairs
• Add some " bling " to your bike
• Helps Keep the air in your tire

Ideal for smaller street bikes or smaller SuperMoto wheels.

Offers safety, durability with a ratio of grooves that has been increased to improve the balance between grip and wear.

Grooves run from the center to the shoulder to facilitate the evacuation of water and offer good grip on wet roads.

Possibly the best value for smaller SuperMoto tires.

Bias-ply and tubeless, S rated (max speed of 112)

• Seal profile is engineered to create equal pressure in each seal lip; equalized seal pressure creates less drag and longer seal life
• Patented MAX-LIFE has a coefficient of friction up to 3 times less than the OEM seal material
• Triple-lip seal design
• Dyno-tested to last 3 to 4 times longer than OEM seals
• Directional ribs allow seal to be installed easily
• Kit includes fork seals and dust wipers
  
   

This adapter set is required to fit an aftermarket spring to the Vstrom shock

Race Tech HP Springs have a high stiffness-to-mass ratio. In other words; the springs are light weight for their particular spring rate. This requires the finest materials and processing. Shot-peened and pre-set so they cannot sack out. All Race Tech HP Springs have the highest rate tolerances in the industry. These are the finest springs in the world-guaranteed.

OEM spring rates are 7.7kg on early models and 8.2kg on later models. We offer stiffer spring rates from 5% to 25% for riders who wish to carry luggage or just prefer stiffer suspension.

Fork brace precision machined from aluminum barstock. Drilled and tapped for optional lower fender attachment.

Hard anodized black for corrosion protection. Fits OEM forks. Split design allows for installing in minutes without having to remove the forks.

Here is everything you need to upgrade your TW200 front suspension. Kit includes: Heavy Duty Fork Springs, Cartridge Emulators, Oil Seals, Dust Seals, and 10w Fork Oil. Just choose the spring rate you want and enjoy your TW even more!

Stock Spring Rate is .50 kg/mm. The .60 kg/mm springs are 20% stiffer than stock while the .70 kg/mm is 40% stiffer than stock.

Installation requires disassembling your forks and drilling out your damper rods.

Damping Rod style forks are notorious for being too harsh, too mushy and too easy to bottom. Gold Valve Cartridge Emulators remedy this problem by controlling the compression damping with a tuneable valve. The Emulator sits on top of the damping rod and is held in place by the main spring.

Simply put; Emulators make damping rod forks perform like well-tuned cartridge forks. Installation and tuning for any condition or rider preference is very straight-forward. 

Simple to install and completely tunable for all conditions and rider preferences.

For a top notch rebuild or re-valve of your rear shock use this high quality replacement seal head.

• Complete assembly, ready to install into the shock body
• Has air bleed holes to help remove air from the oil reservoir during installation
• Double-lip oil seal design keeps out dirt and keeps friction low
• Kits include aluminum body, dust seal, bushing, oil seal, O-ring, internal guide bushing/washer, snap ring, and top-out bumper

Helps protect vulnerable fork tube and seal from dust, dirt, and corrosive elements. These are sewn into a tube and require that you drop your fork tubes down out of the triple clamp for installation. Can still be slid up for easy cleaning. 

32 mm-43 mm Diameter 
127 mm (5") Length
3 mm Thick 

Sold in pairs

• Allows precise valve lash adjustment without disturbing the setting when the lock nut is fastened
• Knurled knob on adjuster drivers ensure a precise and secure grip
• Integrated repositionable wrench handle holds the lock nut while the drivers are used to loosen or tighten the valve adjustment screw
• Includes 10mm socket with straight slot adjuster
• Fit motorcycles and ATVs with straight slot screw-type adjusters and 10mm lock nuts

Convenient tool to hold the clutch basket when servicing your clutch

The DR650 Air Scoop was designed to increase airflow to the oil cooler helping to prolong the service life of your motorcycle.

  Does NOT work with Acerbis 6.6 gal tank.

New replacement side panels specifically made for gen 1 KLR650.

Available in 4 colors.

  Will not fit KLR250

Depending on your application and preferences, more than one optional heat shield may be useful.

Maier headlight cowling in colors to match the ProCycle body plastics kit for the DR650.

Quality replacement headlight fairing for TW200

Quality windscreen made from Lucite aircraft acrylic making it more rigid and optically clearer than OEM windscreens

These models are 2"-4" shorter or 2"-4" taller than stock to meet your particular riding preference.

The long over-due rally shield for the 2008-on KLR650 is finally here!

Parabellum uses 4 steel brackets mounted to factory locations as well as our stand-off windshield design to ensure the customer doesn’t have to drill extra holes in the cowling but still achieves that iconic upright look of the real Dakar Rally bikes.

The Rally shield protects the rider’s torso/chest from air, cold, roost, branches and bushes while leaving the rider’s head/helmet in clean air. We recommend the Rally shield for riders seeking some protection, but prefer to be off-road.

The Rally shield is made from 1/8 inch cast acrylic and is 11.5 inches wide at the bottom and 17 inches tall.

This product has been designed to fit the Yamaha T7 Ténéré

This kit will give you 80mm of adjustment over the stock screen.

In the raised position, the difference in ride comfort is remarkable. Wind noise reduction is very noticeable and airflow underneath your screen reduced the vacuum effect, creating smoother airflow and reducing turbulence.

In the lowered position, the screen sits at the same height as stock.

To adjust the screen, loosen the thumb nuts, slide into position and re-tighten the thumb nuts, no tools required.

The 12oclock Labs EXUP Emulator is used in place of the stock exhaust servo motor when you replace the stock exhaust with an aftermarket exhaust system. The microprocessor controlled EXUP, emulates the exact characteristics of the stock exhaust servo motor and its motor delay sweeps, keeping the ECU from displaying the dreaded check engine light. Weight is less than 1/2 an ounce and it is a direct plug and play replacement.

Motion Factory Racing patented Flex-Mount Footpeg System provides superior grip and allows your foot to flex forward and back with the movement or your motorcycle.

One of the key features of Flex-Mount Footpegs is their unique flex-mount design. This design allows the footpegs to absorb shocks and vibrations, reducing fatigue and improving overall comfort during long rides. Additionally, the adjustable height and angle options ensure a personalized fit, allowing you to find the perfect riding position for maximum control and stability.

The bushings act like the suspension on your bike. With bushings, there are a couple of things to think about. The more firm the bushing the more durable and longer it will last. They use a durometer, a hardness scale 0 being the softest and 100 being the hardest. They don't go below a80 because they found that durability isn't great below this but have tested as low as a60 bushings. A bigger person that rides enduro-style terrain might want an a96 or a98 rated bushing. A lighter person might want the opposite but in the end, it comes down to personal preference. 

They put an a90 bushing on all new mount setups so people can get a good feel for their mid range option. The bushings are high quality yet inexpensive (they achieve this because they use skateboard bushings that are already developed and produced in massive quantities around the world) and a wear item designed to be replaced each season or depending on how hard or often someone rides.  

Complete mount system includes: 

• 6061 Aluminum ADV Platforms (65mm wide x 107mm length) 
• Stainless steel mounts
• Sleeve bearing (8x10x20mm) included for 8mm OD' footpeg pins. 
• Right and Left spring included. 
• Chromoly steel spindles with reusable thread locker. 14mm wrench. Torque spec 40 ft/lbs 
• A90 (medium flex) rated bushings
• Cleats and stainless steel machine screws. M3x18mm. These can simply be replaced by going to your local hardware store when damaged or worn out. 
• Bushing bolts. 8mm Allen wrench. Torque spec 30 ft/lbs

 They designed their hardware to bend rather than break in a significant impact. A wrench or adjustable wrench will quickly and easily bend the bolt back straight. Please avoid using a hammer. A little leverage from a long-handled wrench or pipe will do the job. The whole system is rebuild-able and serviceable.

They Fit Kawasaki KLX110 and Yamaha TW200 however some of these bikes may need a little modification by yourself, Please check the size carefully before you buy. If you make mods to the footpegs for fitments it will void all warranties and return policies. 

Attach this over your brake lever and hand grip, squeeze the brake lever, pull the locking bar in and lock the black portion down. This creates a locked front brake, making parking safe and secure with about 5 seconds of effort.

To unlock the BrakeFix, you just lift the back of the black hooking portion to release it. This takes about 2 seconds. Perfect for use with Snapjack type stands or just parking on an incline.

ProTaper Pillow Top Grip with 3-D (Tri-Density) Technology.  Try the grip with the technical advantage of three dedicated rubber compounds.

• Vibrasonix pillow top reduces vibration and cushions impact. 
• Inner core compound perfects the bonding interface with bars. 
• Anti-Rip Tip™ uses denser compound to increase life of grip. 
• Designed to self-clean and shed mud away from outer surface. 
• Tacky gel-like surface compound is perfect for the trail and MX.

Designed to enhance the appearance of your TW200, yet provide greater riding distance per tankful. This larger fuel tank has double the capacity of the stock tank at 3.6 Gallons, yet very slim and sleek. This tank has a custom design that will allow the use of OEM & Maier side covers. These tanks are made with POLYETHYLENE CROSSLINK for extra strength and durability.

Comes with New Screw Cap.

Requires OEM/Stock petcock and oval rubber grommets for install.

If you do not have the grommets or if your O.E. grommets are in poor condition you can add these to your tank order.

If you just installed aftermarket LED turn signals or an LED integrated tail light and your turn signals are flashing way too fast, or perhaps simply staying on completely, you're at the right place to find the solution! The TST Gen2-SK LED Flasher Relay fixes what we call "hyperflash". It slows the flash rate down to a pre-set 85 cycles per minute but can be sped up or slowed down using the adjustment dial located within the unit so you can get the exact speed you are looking for. The plug-and-play installation means that you don't need to splice in any load balancing resistors that generate unnecessary heat and require splicing into your stock wires. Simply remove the stock relay and install your new TST relay and your wiring job is done. It's that simple!

• Slows turn signal flash rate down to an adjustable 85 cycles per minute when turn signals are experiencing hyperflash or stay on continuously
• Adjustable turn signal flash rate enables you to speed up or slow down the flash rate to fit your preference
• Plug and play installation meaning no cutting, splicing, or soldering
• Replaces the stock relay and fits like OEM
• No need for cumbersome and heat-generating load balancing resistors
• Flexible relay housing enables easy access to the flash rate adjustment dial inside of the relay unit

Please make sure your bike uses a 2-pin relay for the signaling system. If your bike has hazard lights it may need the 4-pin relay. Please also note the pin configuration and make sure it matches what is on your bike. It is very important to verify fitment before making your purchase.

So you say you want more light for your dual sport? Give this 7"DOT legal Rally light a try and light it up like a freight train! HIGH/LOW operation and SAE/DOT/E4 approved. 
 

This light does not have the large Cyclops logos shown on one of the images.

• Race Inspired Design
• Hella reflector, made in Germany  stamped SAE/E4
• Lightweight Aluminum Frame
• Plug and Play for Bikes with H4 Bulbs.
• Available with optional mounting plate for computer or GPS
• Easily converted to HID if desired, uses an H4 bulb
• For bikes that are not H4 (XR650R), a simple H4 plug available at any auto parts store will allow you to use this light.
• Now the panel on top of the light for mounting speedos/gps's etc is included, (This is a platform, not actual GPS mount.)

Optional 10.0 Lumen LED High/Low Upgrade  and now the Phoenix LED complete headlight for the ultimate DOT headlight
The stock lamp that comes with this rally light is great, but you can get  well over double the brightness  with the LED upgrade at a substantially lower power draw. Note if your bike is ac powered at the headlight you will need the rectifier for the LED option.. AKA carbureted KTM's CRFX and XR400/650.. others may apply.

The Mojave Series LED Racing Lights have been designed to survive and operate in extreme conditions. Lights feature a heavy duty housing that can withstand hard impacts and a lens that is twice as thick as traditional lights. The light includes three different replaceable lens (Flood, Spot, and Combo).

Features:

• Heavy Duty Design​
• IP69K Rating​
• Flood, Spot / Flood, & Spot Lens Included
• Stainless Steel Bracket & Hardware​
• 5,000k Light Color – Natural Daylight
• Heavy duty black steel left & right mounting brackets to bolt directly to your lower triple clamp.
• Harness with Switch

This kit will work with the 6.6 Gallon Acerbis fuel tank for the DR650. You must run the light brackets inwards in order for there to be proper clearance with the 6.6. Gallon tank.

The Front Rack gives a lot of options for functionality.

CycleRacks are made out of Schedule 40 11/16 black steel pipe, bent in a press, and welded together in a jig.

All of their products are 100% made in the USA. If the rack is ever broken for any reason, CycleRacks will replace it for free, you just pay the shipping.

Hand built aluminum luggage rack from the B&B Off Road Engineering folks down under. This unit really is a beauty to look at and extremely rugged, made from 4mm 5083 aluminum plate! Tie down whatever you need with confidence. Whether it's your books to get to school or a bag to get across the country, no worries mate. Available in either bare polished aluminum or with a black polymer coating.

While plenty rugged to use as grab handles, you can keep your stock handles if you so desire. All necessary stainless clamps and bolts are provided.

If you want a wider platform for support, consider adding the luggage plate to this rack.

  Bike must have the DR250 Taillight installed to work with this rack.It will not work with the stock USA taillight.

This kit fits all Nomadic tubular type racks. (All flat stock racks are already RotoPax compatible)

The second image shows the kit, which includes all the hardware and instructions required. The lower image is just an example of what the eXpander looks like mounted to one of their racks.

Not only are Pro Moto Billet Cargo Racks brutishly strong and functional, but they look great too. Each cargo rack is methodically engineered, then CNC machined on-site from a 1/2 inch thick plate of USA made 6061 aluminum by master machinists.

The cargo racks are then hard clear anodized for durability. PMB uses only stainless steel fasteners for worry-free years of riding. Excellent instructions and all necessary har

Need to mount your turn signals to your new Pro Moto Billet Rack? Just add a set of CNC machined aluminum Turn Signal Brackets and that will be no problem. See bottom image.

Note: Placement of this top rack does require removal of the stock tool bag.

• Strong and durable hydro-formed 4mm aluminum for rigidity and low weight
• Black powder coating resists corrosion and keeps the plate looking good even with a little abuse (because we know you will)
• Specially designed for maximum stiffness for optimum support while remaining lightweight
• Designed to mount TRAX top cases and SysBag 15/30 soft bags (adapter kits sold separately)
• Large 1in bungee slots allow easy securing of soft luggage.
• Simple assembly to original attachment points with bike-specific components

T7 Solo Carry rack has been designed predominantly for the solo rider to keep loads as forward and low as possible. The plate has multiple attachment points making easy to tie down bags.

The plate is pre-drilled for mounting systems for both Givi monokey and Rotopax. The rack is light in weight only weighing 2.3kg.

• Fits with standard seat only. Will not fit with Rally seat
• Fully tig welded
• Comes in polished or black PPA coating.
• All hardware for mounting is included.
• Made from 5mm thick cnc machined plate
• 420mm x 260mm surface area
• Slim design
• Compact and rigid
• 4 Bolt removal

Innovative anchor knot attachment system with an anti-slip cam buckle system that allows you to install or uninstall the bag quickly. Quick-release mounting system with adjustable hook-and-loop straps and an under-seat center strap.

• 1200-denier Technolast UV-treated polyester construction
• Comes with a 100% waterproof rain cover
• Expandable rain covers included
• Measure 14" L x 5.5" W (expandable to 9.5" W) x 10" H
• Minimum volume: 25 liters
• Maximum volume (when expanded): 44 liters

Every backcountry adventure-seeker needs a handful of these multi-purpose straps with virtually unbreakable fasteners. Each pair of stretch polyurethane Pronghorn Straps™ feature stamped aluminum buckles sheathed for scratch protection with arrows that line up for easy fastening. Each buckle prong holds the strap in place for pre-fitting and easy chaining of straps together.

Available in color-coded 18-, 25- and 32-inch lengths and marked by size, you’ll find a million uses for Pronghorn Straps—motorcycle, sled, snow bike, 4×4, ATV, UTV/SXS—and so much more!

Our Tool Tube mounts in place of the little stock tool carrier. The tube is made from 3 1/2" O.D. ABS pipe. It's held by 3 strong powder coated steel straps. Both ends are sealed with waterproof expanding plugs. This is the ideal way to carry those items you always want to have with you on every ride. Tube is approximately 13" long.

You can now order your Tool Tube with a Locking End cap, mini padlock and keys included, on the exposed end.

If you already have a Tool Tube you can order just the Locking End Cap and lock.

*Rear fender with minor superficial scratches on the top of the fender, most likely not visible unless looking up close, and some will be covered when installed. Sold as is. Includes all pieces for complete rear fender kit.

ProCycle Plastics (formerly DSA) Rear Fenders include LED tail/brake light and license plate holder. Vacuum molded, these parts are a design improvement over stock.

Only available in Blue.

In order to be prepared for all possible mechanical mishaps along the trail or on any adventure, we are required to carry a certain selection of tools. The OBR ADV Gear Tool Roll will help keep those tools together and stored in an organized fashion easy to be found should one of those mechanical mishaps occur.

Features

• Heavy duty ballistic nylon construction
• Heavy duty #8 coil zipper
• Individual Tool Slots for Tire Irons, Wrenches, Screw Drivers … along with a zippered pouch providing secure storage for those smaller items
• Detachable 10”x10” slip pocket cover flap that also doubles as a hub pad keeping your hub out of the dirt when changing a flat
• Open dimensions 11” x 17”

All the advantages of a flatslide pumper carburetor at a much friendlier price than a Keihin FCR.

Our complete genuine Mikuni TM40 pumper carburetor kit comes with alloy adapter rings bonded to the carburetor body for a firm reliable fit in the stock air boots. We also include a remote mounted choke knob, complete instructions along with a wide range of main jets and pilot jets for fine tuning or to accommodate bikes with extensive modifications.

Made of military aircraft grade 3/16" cast acrylic, this guard will protect your lens from roost, rocks and branches. Optical clarity of the acrylic ensures brightness and projection of your headlight are minimally effected while all the while protecting your headlight from impact and abrasion.

Guards are held to the headlight lens with an industrial strength hook and loop system on each corner.

• Extracts dirt and debris trapped between fork seal and tube
• Easy way to keep fork seals clean and debris free
• Works on conventional and upside-down forks

A 3-pack of easy to apply strips measure the temperature of engine, suspension, and radiator components. Temperature range 149° to 248°

• High sound level 105-118 db
• 80mm diameter and only 7.5 oz
• Wire extension included
• Universal for street and off road use

Here's an easy way to add a Tach to your motorcycle. 

• Tachometer from 0-19,999 rpm
• Non-resettable hour meter from 0-99,999 hours
• Easily mount it to any surface using either the bolt-on (screws not included) or peel-n-stick mounting options
• "Wrench Icon" with hours
• The smallest available meter at 50 x 25 x 14mm and has large, easy to read digits

This high output stator will allow you to run brighter lights, heated gear, heated grips, etc. From ElectroSport

Made with heat-treated carbon steel for longer wear life and reduced galling. Stock size, simple bolt-on procedure.

High Quality Replacement Wheel Bearings and Seals for your TW200.

Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.

Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.

Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.

Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.

Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.

The rubber coated outside diameter creates an optimum seal at the hub.

Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.

A super compact shovel with several bonus features!

• Lifetime Warranty
• Compact and Portable Design
• Integrated Survival Features
• Durable and Versatile Cosntruction
• Hidden Tools Threaded in the Handles

Is the cylinder head intake boot on your DR650 cracked or weathered, is it missing parts of the lip to seal around the carburetor, have you recently pulled the intake boot off only to realize the O-ring behind it is hard & brittle? This kit is your solution to solving some of those mystery problems and make your bike like new again. There can be a great deal of heat that can radiate behind the cylinder head on a DR650 as it is an air cooled engine. With that comes long term maintenance items that will need to be replaced due to them being made of materials that cannot withstand those constant heat cycles indefinitely.

Our kit includes O.E. parts from Suzuki to include:

1. Intake Boot
2. Metal Clamp
3. Premium Japanese O-ring

• Fits directly into OEM airbox with application specific Sealing Bead to ensure a precise fit
• Fuel-management modifications are not required for increased performance
• Pleated media provides a large filtration area offering long service intervals
• Washable and reusable, pre-oiled and ready to ride
• Designed to provide increased performance

Hiflo filtro air filters are manufactured to fit the factory air box and are a direct replacement for original equipment filters. Top quality powerflow filtering media, developed for modern high performance engines.

Our Tool Tube mounts in place of the little stock tool carrier. The tube is made from 3 1/2" O.D. ABS pipe. It's held by 2 strong powdercoated steel straps. Both ends are sealed with waterproof expanding plugs. This is the ideal way to carry those items you always want to have with you on every ride. Tube is approx 13" long. Long enough to carry your Tire Iron Wrenches.

You can now order your Tool Tube with a Locking End cap, mini padlock and keys included, on the exposed end.

If you already have a Tool Tube you can order just the Locking End Cap and lock.

This brake bleeder makes bleeding your brakes a one man job.

The unique check valve allows fluid and air to escape while preventing air from re-entering the system.

The ProCycle seat was designed for both comfort and function. Our seat is built with an advanced Progressive Density Foam (Pd-F) for those long days in the saddle, and also giving you freedom to move while standing. 

The wide and sturdy seat makes long rides more comfortable. The vinyl weave helps keep you cool by letting air flow between you and the seat. The front of the seat is narrower, giving you space for your knees when you're standing, while the sides have grip so you can hold on with your knees while riding. 

We will build the seat for you in-house on a new seat pan so all you have to do is put it on and go ride. Choose the heated seat option and we will add a Seat Warmer during the build process.

Canyon Dual Sport saddle is designed specifically to provide long range comfort for your Tenere 700. We also offer a Bench style saddle that provides more freedom of movement for you that leans towards off-road riding.

Their high density Comfort Cell foam allows a sleek profile, while providing a firm supportive ride that lasts. Rider seating is ergonomically shaped to fit the curve of your body and provide better weight distribution. This also helps to eliminate the centralized pressure felt from the stock seat. In the nose area, they sculpt the saddle narrow to allow for good ground reach. Canyon Dual Sport has a seat height between the Yamaha Rally seat and Yamaha Low seat.

Passenger seating area is designed with a neutralized platform to curb sliding forward in the saddle. Dished shaping provides an excellent contact patch while maintaining a clean look. For the best combination of looks and support, add the Ovalbac backrest shown. This backrest provides a generous, contact patch for excellent support. Angle adjustment is simple and can be performed without removing the saddle or backrest from the bike.

For an added luxurious touch, this saddle is available with the option of electric seat heaters. With the flip of a conveniently located switch built into the left side of the saddle, both the rider and passenger seating platforms will heat up and maintain temperature automatically. Simple to install with just a pigtail wiring to your bike's fusebox. All other components are built into the saddle and come preinstalled.

The design shown above includes Black Carbon-Fiber leather seating with Matte Black vinyl contrasting sides and a tasteful color coordinated Smoke Gray welt.

The default cover choices are black 'carbon fiber' on top and 'asphalt' on the sides, 'no welts', black logo. You can view all of the available materials and colors through the link below. If you would like your seat built with something other than the standard choices please state specifics in the comments during check out.

You want a lighter replacement for your heavy steel stock tank? Don't need the extended range (or bulk) of a big tank? The 3.7 gallon tank from Clarke might be just right. It's almost 5 lbs lighter and holds close to 1/2 gallon more fuel than stock to increase your range by about 20 miles. Fits with your stock petcock, Pingel or Raptor petcock.

These brake fluids are motorcycle approved DOT 4 brake fluid, and is specially formulated to exceed all DOT 3 & DOT 4 specifications. What this means to you is exceptional resistance to vapor lock and maintaining consistent lever feel during extreme brake use.

License plate holder has been designed to replace the bulky standard assembly with a sturdy, neat unit. The Tail tidy accepts the standard Yamaha blinkers and is supplied with a LED number plate light.

• 3 piece CNC machined from high-quality alloy
• Designed to bolt straight into position with no modification to the bike
• Available in polished or black ppa coated

It is a good practice to replace your sealing washer with every oil change. These 10 piece kits are made up of 5 Copper washers and 5 Aluminum washers. The manufacturer recently decided to make half of the kit Copper washers as that is the material of choice for many OEM manufactures. This gives you the opportunity to decide which you prefer, but either will work great at creating a leak-free seal between the case and the drain plug.