Search Products

For adjusting valve clearance on twin cam models. Holds valve spring collar down so adjusting pads can be removed. From Motion Pro, made from hardened alloy steel.

This is a standard H4 bulb that has a 80 watt low beam and a 100 watt high beam. This is an easy lighting upgrade that should not over tax a stock charging system.

This replacement lens has a clear panel on the bottom to illuminate your license plate. 

Allows you to bolt your license plate directly to the rear fender. 

Does not fit Australian DR650.

The SignalMinder unit is designed as a plug-in accessory for many Japanese bikes. SignalMinder uses a microprocessor to cancel the turn signals at one of three selectable time outs; 10, 20 or 30 seconds.

You can also make it so that all four of your signal lights also act as running lights and establish a dual-channel system on your bike. With the dual-channel system, when you activate the RIGHT turn signal three times in succession, you get 4-way hazard flash lights.

Connecting the 12 volt supply from the brakes to the SignalMinder, also allows for a brake flash option.

There are many options and configurations using this electronic tool.

No wire cutting required. The kit includes Scotchlok connectors to tap into existing wires.

Aluminum alloy lowering link. Lowers the rear suspension approximately 1 inch.

Bearings included.

Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.

Kouba lowering link will lower the rear suspension 1.75". Comes with bearings and seals installed for a quick and easy installation.

Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.

The progressive factory springs are well known to be way to soft for most riders. Cogent Dynamics straight rate springs will give better control in the rough stuff and when loaded up.

Sold in pairs.

0.72kg/mm riders up to 260lbs

0.80kg/mm riders 260lbs and up

The 0.72 springs are 28% stiffer than stock and will be a great choice for most riders

Not compatible with Adventure Sport ES

Included in this kit are fork springs, Cogent DDC (Drop in Damper Cartridge) performance cartridges and three bottles of 5w fork oil. Refresh those tired old forks and make them better than new. These DDCs from Cogent are easy to install. No taking the forks apart, no drilling of the damping rods, nothing. Just take them off, flip them over to drain the oil, add new 5w oil, drop in the DDCs and then add the springs and spacers and then install the caps. Preload spacer material is included with the .47 and .70 springs, additional spacers are not needed with the other kits.
This upgrade offers better control off-road as well as on. Less brake dive keeps the fork up in the middle of the stroke on-road and better control off-road whether it be rolling water bars or bouncing off the rocks.

• Rider and Gear up to 160lb. = 0.47 springs → 24% stiffer than stock
• Rider and Gear 160-225 lb. = 0.52 springs → 39% stiffer than stock
• Rider and Gear 225-275 lb. = 0.58 springs → 56% stiffer than stock
• Rider and Gear 275-325 lb. = 0.63 springs → 66% stiffer than stock
• Rider and Gear 325 lb.-UP = 0.70 springs → 84% stiffer than stock

An excellent replacement for the stock fork boots. These are great for protection from dirt, rocks and other contaminants. These boots utilize the latest advances in material technology to adapt to fork and styling demands. These high quality fork boots are 1/4 the price of the OEM factory replacements.

Race Tech HP Springs have a high stiffness-to-mass ratio. In other words; the springs are light weight for their particular spring rate. This requires the finest materials and processing. Shot-peened and pre-set so they cannot sack out. All Race Tech HP Springs have the highest rate tolerances in the industry. These are the finest springs in the world-guaranteed.

This spring is 8.0kg/mm

OEM spring rates are 5.7-7.6kg/mm progressive style.

Heavy duty shock bumper. The stock bumper is prone to disintegrating with age. If you are re-valving your shock it's a good idea to be sure the bumper is in good shape.

Damping Rod style forks are notorious for being too harsh, too mushy and too easy to bottom. Gold Valve Cartridge Emulators remedy this problem by controlling the compression damping with a tuneable valve. The Emulator sits on top of the damping rod and is held in place by the main spring.

Simply put; Emulators make damping rod forks perform like well-tuned cartridge forks. Installation and tuning for any condition or rider preference is very straight-forward. 

Simple to install and completely tunable for all conditions and rider preferences.

Use this installation tool from Cogent to be sure that your Cogent Drop-in Dynamic Cartridges are installed correctly. A strong magnet in the end holds the cartridge firmly while you lower it into your fork leg. Then slide the spring over the tool until it holds the DDC down, then gently remove the tool. That simple. Never again question if it is properly seated on the damper rod.

Works equally well for removal when you need to change your fork oil. Also works great with Race Tech Emulators.

Designed to enhance mid-range and top-end power. Manufactured using the highest quality standards. No core required.

Note: This camshaft has been designed to work with the OEM Yamaha piston, or the BBR big bore kit piston, with OEM sized valves. Any other combination of parts will require that you manually check valve to piston clearance.

A head gasket and base gasket to fit the Big Bore cylinder.

High quality clutch cover gasket. If you are servicing your clutch, a new gasket will prevent oil leaks.

Billet plugs for your left side case. 

Includes both the timing mark plug and the crankshaft access plug.
 

Made from laser-cut, medical-grade, 304 stainless steel micronic filter cloth, this filter provides 200% more filter area over many paper filters, catching debris down to 35 microns. The FLO filter pleat seam is welded and able to withstand up to 600 deg. F. Filter maintains consistent flow under all conditions including extreme heat, the presence of water and cold start-ups where paper filters can flow so poorly that they often cause the bypass valve to open and allow unfiltered oil to enter your engine.

This cleanable oil filter should be the last one you ever purchase.

Providing unbeatable performance and exceptional value, Hi-Flo is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide.

Grab our 5-pack and save both time and money!

Providing unbeatable performance and exceptional value, Hiflofiltro is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide. The filters are also supplied to original equipment manufacturers as well as private label brands.

You pay $3.59 per filter with our value 5-pack!

This is all you need to not only change your oil, but protect your motor as well. We include a magnetic drain plug, to help catch stray metal pieces, a 5-pack of oil filters, and new O-Rings to replace any you have that may be leaking or worn.

• Magnetic Drain Plug
• O-Ring Kit
• 5-Pack of Oil Filters

This is all you need to not only change your oil, but protect your motor as well. We include a magnetic drain plug, to help catch stray metal pieces, a 5-pack of oil filters, and new O-Rings to replace any you have that may be leaking or worn.

• Magnetic Drain Plug
• O-Ring Kit
• 5-Pack of Oil Filters

This is all you need to not only change your oil, but protect your motor as well. We include a magnetic drain plug, to help catch stray metal pieces, a 5-pack of oil filters, and new O-Rings to replace any you have that may be leaking or worn.

• Magnetic Drain Plug
• O-Ring Kit
• 5-Pack of Oil Filters

• The new 3rd generation Motion Pro Revolver variable rate throttle system is here!
• Innovative reel changing system lets you tailor the throttle rate to your preference and riding conditions
• 5 different reels provide perfect throttle response for any condition. Use smaller reels for slower throttle rate and larger reels for faster throttle rate. Included cam reel provides progressive throttle response preferred by some riders
• Slim REV3™ throttle housing allows more room for lever clearance and adjustment to throttle housing position
• Improved throttle stop provides greater strength and durability
• Snap together elbows makes it even easier to install and change reels
• Cable boot keeps dirt and dust out for reliable and smooth operation
• REV3™ off-road kits are compatible with the new Motion Pro DirtControl™ V2 Lock-On grips and ODI Lock-On grips
• Billet aluminum inline cable adjusters ease installation and adjustment
• Lower section of cables use 5 mm housing with PTFE liner for reduced friction, increased routing flexibility and lighter weight
• Upper section of cables use 6 mm housing to provide solid support of adjusters
• Simple to install and maintain
• Patented

Kit includes:

• REV3™ throttle assembly with throttle tube (REV3™ off-road kits include the unbreakable Titan Throttle Tube™)
• Motion Pro REV3™ black vinyl cables specifically designed for your bike
• REV3™ sportbike kits include Motion Pro RoadControl™ grips
• Four interchangeable round reels: 35 mm, 40 mm, 45 mm, 50 mm
• Progressive cam reel - Sportbike kits include road race profile cam reel (orange)

Quality replacement clutch cable.

• Nylon-lined housings and precise OEM component dimensions

Replace the soft stock lever with sturdy forged aluminum.

Folding tip prevents snagging.

Hardened splines won't slip or rotate.

A set of replacement brake and clutch levers. Standard length.

The Trail Mirror is a simple solution for any dirtbike or mountain bike. Gives you hindsight when you need it, but you forget it's there otherwise. 

• Made from super tough glass reinforced Zytel
• Reflector diameter: 2" (50mm)
• Bar space: 0.75" (19mm), Height 1.25" (32mm)
• Convex lens for wider field of view

Zip ties directly to the bar- no hardware required.

Sold individually

The GPR v5 is the fifth generation steering damper designed for dirt bikes, adventure bikes but is also used on several of hybrid applications. Its compact and slim design allows for the damper to be mounted below the handlebars, out of harm's way, without raising the bars more than an inch. Frame mounts are machined steel or Cryogenic treated billet aluminum with stainless steel pin, and billet aluminum machined bar-mounts.

• Kit includes damper, bolt on post mount, below the bar mounting system, and complete instructions.
• Bolts onto the OEM triple clamp replacing the stock handlebar mount. Will raise the Bar height about 7/8th". Fixed position.

• Will only work with Fat Bar style (1 1/8" clamp area) handlebars and stock triple clamp.

The long over-due rally shield for the 2008-on KLR650 is finally here!

Parabellum uses 4 steel brackets mounted to factory locations as well as our stand-off windshield design to ensure the customer doesn’t have to drill extra holes in the cowling but still achieves that iconic upright look of the real Dakar Rally bikes.

The Rally shield protects the rider’s torso/chest from air, cold, roost, branches and bushes while leaving the rider’s head/helmet in clean air. We recommend the Rally shield for riders seeking some protection, but prefer to be off-road.

The Rally shield is made from 1/8 inch cast acrylic and is 11.5 inches wide at the bottom and 17 inches tall.

Moose Adventure Windscreen

• Made from aircraft-quality Lucite®​ acrylic
• Heavy-duty, optically clearer than the OEM windscreens
• Available in various heights and sizes
• 5" Shorter version reduces buffeting and improves warm-weather comfort
• Made in the U.S.A.

B&B Off Road Engineering Fender Brace is made to help support your front fender/guard. Also helps support and reduce fatigue from constant vibration.

Made from 4mm 5083 structural aluminum plate. If you wanted to carry a small tool bag this would be a perfect product to support the weight and strap the bag to.

Fits on top of the fender and bolts between the fender and bottom triple clamp. Requires you to drill one hole in the fender for mounting.

Ditch the stock ugly plastic sub-fender and install a B&B Off Road Engineering License Plate Holder. Comes with an LED light to keep the license plate lit up.

Quality replacement headlight fairing for Gen 1 KLR650.

Available in 4 colors.

Quality MX style rear fender from Maier.

Quality replacement radiator air scoops. Sold in pairs for gen 1 KLR650.

Available in 4 colors.

This is the more economical alternative to eliminating the 990 Adventure airbox. Better breathing equals more power. The ITG filter kit makes air filter service a snap. It also simplifies other engine and intake maintenance chores. Our kit features a steel base plate which will not deform like plastic and does not conduct heat as much as aluminum. The white powder coating also helps reflect engine heat. To take advantage of the increased airflow, we recommend upgrading your fuel injection map with TuneEcu or a Power Commander.

• OPTION - Twin Air Breather Filter (replaces standard breather filter)

This kit will replace your stock sprocket bolts and nuts with new hardware.

Factory Honda replacements in a convenient kit.

Quality steel rear sprockets.

Color may vary based on manufacturer availability, quality will not be compromised.

JT Sprockets are made from the latest generation of computer design and control metal cutting equipment for maximum durability. Front sprockets are made from chromoly SCM420 steel alloy. All sprockets are heat-treated and hand-finished to meet or exceed the highest possible quality standards.

Currently available in 15 tooth size only, other sizes coming soon.

This an OEM replacement nut for your front sprocket.

The chain slider protects the swingarm from contact with the chain. Replace yours before it wears through to the swingarm.

Giant Loop’s 8-liter Fandango Tank Bag provides easy access to fuel, room enough to pack gear for a day trip or a long-haul journey, and is loaded with rider-friendly features similar to its smaller counterpart, the 6-liter Diablo. With its larger capacity, the Fandango provides riders a convenient way to carry larger items such as a DSLR camera, rain gear, first-aid kit, and more.

The Fandango makes packing a breeze with its handy movable interior divider featuring elastic organizers and a spot for your tire pressure gauge. With a fully lined interior that's compatible with hook-and-loop fasteners and an exterior mesh pocket, you'll have plenty of options to keep everything neat and tidy. Plus, if the weather decides to take a turn for the worse, we include a waterproof Tank Bag Dry Pod™ to keep your sensitive gear safe from moisture!

• Harness Dimensions: 8.5″ wide X 12″ long
• Tank Bag Dimensions: rear 8″ tall, front 5″ tall, 8″ wide
• Volume: 8 liters
• 22 oz vinyl coated polyester Bomb Shell™ reinforced with foam
• Slip-Not and clear vinyl top
• Rubber electronics port
• Water resistant YKK zipper (bag)
• Beefy YKK coil zippers (harness)
• Nylike webbing
• Reflective accents for visibility

The Diablo delivers six liters of rider-friendly on-bike storage by following Giant Loop’s strict design objectives to build minimalist, slim and trim tank bags that seamlessly integrate with the motorcycle. Even when standing on the footpegs while riding off-road, the Diablo never gets in the way thanks to its unique size, shape, and mounting position behind the gas cap using their secure universal harness mounting system.

Fuel fills are a breeze with the Diablo: unzip the tank bag from the harness for quick and easy fuel access. Add to that, electronics pass-throughs integrated throughout each compartment, a full-length interior lining with hook-and-loop-accepting fabric compatible with many camera bag dividers, and included waterproof Giant Loop Tank Bag Dry Pod; the result is a bulletproof adventure-ready tank bag.

Possibly the ONLY water, dust, mud, and snowproof fender bag on the market today! Giant Loop’s adventure-proof version offers a roll top design and secure connection options for most dirt bike plastics that, when properly installed, stays on no matter what the adventure. Sized to fit a full-length set of tire irons and other relatively small, lightweight essentials, such as a spare inner tube, CO2 inflator, gloves, and other trail essentials.

• VOLUME: 3.5 liters
• DIMENSIONS: 10.5″ x 5.5″ x 3″
• WEIGHT: 13oz when empty
• INCLUDES: 2 Rubber Boa Straps – mil-spec elastic shock cord with heavy-duty injection molded components

Round The World Panniers™ offer a flexible, impact-resistant, and waterproof alternative to a large touring hard pannier set — giving you every bit as much packable volume and convenience without the extra weight and bulk of hard boxes. The largest capacity pannier in their product line, Round The World Panniers, offer 90 liters of packable volume that’s ideal for everything from a weekend of motocamping to long-haul adventure motorcycle travels. They are also great for riding with two people and carrying their gear.

Roll top with durable side-release buckles for secure closure and load stability.

Included set of two seam-sealed waterproof inner liner Dry Pods™ keep gear dry and organized.

• VOLUME: 90 liters (5,490 cubic inches) (45 liters per side).
• DIMENSIONS:
  PANNIER BODY: 21″ tall x 15″ wide x 7.5″ deep (51 cm tall x 38 cm wide x 19 cm deep)
  FRONT DRAWSTRING POCKET: 7.5″ x 11″ x 3.5″ (38 cm x 28 cm x 9 cm)
  REAR ROLL-TOP POCKET: 7.5″ x 11″ x 3.5″ (38 cm x 28 cm x 9 cm)
• WEIGHT: 10.4 lb. (4.7 kg.)
  14.8 lb. (6.7 kg) with optional GL Pannier Mounts and hardware.
• MATERIALS: Rugged Bomb Shell™ coated fabric construction with sewn seams, reinforced ballistic nylon impact zones, and reflective trim. Heavy-duty fasteners.

Pair Round The World Panniers with GL Pannier Mounts for the ultimate in lockable, quick-mount, quick-release convenience.

The Giant Loop Tow Strap is a multi-functional tool that helps get you or your riding friends out of sticky situations.

This Cordura® Ballistic tow strap, designed with sewn loops on each end, can be girth hitched around a tree, bumper, rock, etc.; or used with footpeg-to-footpeg or other motorcycle (and snowmobile, ATV, snow bike) towing techniques. Constructed in the USA from ultra-durable custom woven Cordura® Ballistic webbing, which folds up into a compact integrated cover made with 22 oz. vinyl-coated polyester, or what they like to call “truckers tarp.”

Doubles as a quick deploying, super-strong ridge line for pitching a shelter tarp.

• DIMENSIONS: Measures 14’-9″ L (450 cm), with 6″ (15 cm) loops sewn into each end. 10″ L x 2″ W x 2″ D (25 cm L x 5 cm W x 5 cm D) (packed)
• WEIGHT: 5 oz. (141 g.)

Color may vary based on manufacturer availability, quality will not be compromised.

A 'wrench style' tool to turn the 'square top' tappet screws. The wrench does a better job of holding the adjuster screw still while tightening the locknut. Slim and flat, this tool is easy to carry in a tool pack.

• Hardened metal rotor/disc locks resist cutting, sawing and chisel attacks
• Comes with carry pouch and a disc lock reminder cable
• Includes an extra mini flashlight key for three total keys
• Features a durable push button lock with high security anti-drill round key lock cores

This gasket seals the joint between the head pipe and Exhaust port. These gaskets are designed to crush a little bit to tightly seal where the pipe fits to the head. Get a fresh one now avoid having an exhaust leak when you install your new exhaust.

The RS-2 is a potent and versatile design that evolved from their original TRC, engineered to provide increased power delivery. With a different pyramidal shape that features increased volume, the RS-2 is a quieter system with a larger core — and it offers the added bonus of outstanding performance in a value-priced package.

• Diamond-shaped sleeve
• Large core and increased muffler packing volume means quieter operation
• Stainless steel cone end-cap
• Stainless steel tail-pipe
• USFS Approved spark arrester included
• 6.8 lbs lighter than stock

We recommend Anti-Seize on exhaust fasteners

The Hi-Output Slip-on gives the bantamweight Monkey a heavyweight punch with a deep throaty growl and a beautiful stainless brushed finish.

• 3/4 System; Mid-pipes and muffler
• CNC Machined Billet end cap
• Laser engraved logo badge
• Laser-cut chassis cover
• 3 lbs lighter than stock

• Made from strong and lightweight aircraft aluminum
• Protects vital engine parts from rocks and debris
• Custom fit to your specific bike model
• Oil drain hole for easy access
• All mounting hardware included

A Radial tire specifically designed for small displacement sport bikes. Advanced belt design and Jointless Band (JLB) rear tire construction utilizes a continuously wound belt for smooth performance and a consistent tire contact patch. Aggressive sport-derived treat pattern for enhanced on-bike appearance.

These tires are all tubeless and H-rated (max speed of 130 mph)

Tractionator Dual Venture from MOTOZ. Based on the popular Tractionator Adventure and Tractionator RallZ front tires, but not directional!

• Off-Road performance with great on-road manners. ( 70% dirt / 30% street )
• Proven construction and compound for adventure and dual-sport use.
• Designed in Australia for dependable performance in a wide variety of conditions without the need to change tire pressure between off-road and on-road.
• Hybrid compound with Silica for optimum grip in mud, snow, and rain.
• Reversible for extended use.

NOTE: Tubes can be run in Tubeless tires, but a Tube Type tire cannot be run Tubeless.

Dual purpose tires made for 60% street, 40% off-road.

Excellent performance on dirt, gravel and bad roads.

Tube type, S rated (max speed of 112 mph)

The Bridgestone AdventureCross AX41 Tires features a distinct pattern design, compound and high cross sectional area to provide enhanced performance on or off-road.

This 30% street/ 70% off-road adventure tire that complements the modern dual sport motorcycles.

These are all tubeless tires that are also OK to use with a tube on spoke wheels.

This is a great Dual-Sport tire from Dunlop. Designed for the true 50/50 rider. An Adventure product for the price-conscious customer. Full tread depth pattern designed for rigorous off-road use yields excellent traction on everything from hard-packed fire roads to soft single-track trails. Versatile tire performance allows riders to travel on the street and venture off-road. A tire equipped to go anywhere, the D605 is a value option for the all-around rider. DOT approved.

Standard Duty tubes are made with seamless construction from natural rubber with heavy duty valves. Great replacements for stock tubes and perfect as spares to carry on your bike.

• 17" tube works with 110/90, 120/80, 120/90 (4.00 to 4.25) tires
• 18" X 3.75 tube works with 110/90, 120/80, 120/90 (3.75 to 4.25) tires
• 18" X 5.10 tube works with 110/90, 120/90, 130/80, 130/90 (4.00 to 5.10) tires
• 19" tube works with 100/90, 110/90 (3.60 to 4.10) tires
• 21" tube works with 90/90, 90/100 (2.75 to 3.00) tires

Don't forget a Rim Strip. New tubes deserve new rim strips.

Made with heat-treated carbon steel for longer wear life and reduced galling. Stock size, simple bolt-on procedure.

Rotors are laser-cut from high-carbon content 410 stainless steel then lap cross hatch ground and heat-treated. The finished rotors are mounted on a floating black steel carrier for durability and strength.

The oversize floating pins are CNC machined stainless steel rivets with stainless wave washers to ensure they will not crush as more traditional steel pressed rivets can. Finally, high-temp paint is applied to surfaces like cooling holes and edges to provide a clean, finished look.

Includes a fresh set of brake rotor bolts.

The ProCycle rack system is designed and manufactured by dual sport riders that know what it takes to create a durable and versatile luggage rack.

Our racks allow for easy installation of both soft and hard luggage.

See the linked instructions for how-to videos.

The ProCycle side rack is designed and manufactured by dual sport riders that know what it takes to create a durable and versatile luggage rack.

Our racks allow for easy installation of both soft and hard luggage.

Side racks only, top rack sold separate.

Compatible with the following top racks:

• ProCycle
• Pro Moto Billet
• Pat Walsh
• Nomadic
• TCI Borrego
• Stock Suzuki (must grind 1/8" off inside of frame mounts)

ProCycle rack installation requires removal of the stock grab bars. Turn signal brackets will be needed if using a top rack that doesn't offer turn signal mounting holes.

Construction

• 5/8" steel tubing
• Computer precision bending
• Durable powder coat finish
• CNC cut brackets
• All mounting hardware included

PMR side utility racks are great for strapping down your soft luggage and keeping it off the rear plastics and exhaust pipe, while adding plenty of new tie down points for any luggage you have on your seat or tail section. They also add an enhanced level of security and strength to the rear end of your motorcycle in the event of a tip over or crash. 

Sold as a pair.  Easy to Install

• Complete with all necessary mounting hardware
• Fabricated with 1/2 inch steel tubing, MIG welded
• Finished with a semi gloss black industrial grade powder coat
• Comes with left and right side racks, each side weighs 2 lbs

The CRF300L side racks are intended to work hand in hand with their ENDURO Series rear rack. 

If you plan on installing the side racks without their rear rack, you will need the spacer kit to fill in the empty space, which we will send to you at no extra cost. Please select the option when you place this in your cart.

Please note that you will need to remove the left side rack to access your lockable factory storage hatch.

This DRZ400 rear rack, hand-built by B&B Engineering in Australia is made from 4mm aluminium 5083 plate tig welded to the support tubing circumventing the plate. This material was chosen because of its extreme suitability for welding as well as abrasion and impact resistance, and all of this keeping in mind the full weight of the bike and rider. Once complete they are given a polished finish or coated with a super-durable black polymer. All Carry/Luggage Racks are supplied with the necessary stainless clamps and bolts where possible.

These racks are smooth and sturdy enough to use as a grab handle.

Check out the bolt-on Luggage Plate for the B&B Rack for those times you need to carry a larger load!

A collection of waterproof bags made by industry giant Givi. There are five different bags available, a 30, 20, 40 and 80 liter waterproof roll top bags and then a 20 liter back pack with padded straps and padded back.

The perfect dry trail pack from Moose. Constructed of heavy-duty waterproof tarpaulin with heat-welded seams. Heavy-duty ITW quick-release buckles and YKK water-resistant zippered external pockets make for a versitle bag.

The roll-down top creates a truly waterproof seal for the main compartment. Dual compression straps provide a secure closure and can be used to store gear externally as well. Coated tarpaulin material makes cleaning a breeze. Available in three great sizes - 25, 40 and 60 liters.

If you like these bags, you might like the matching ADV1 Backpack.

Hot Shot Series Honda CDI Box; Rick's aftermarket Hot Shot CDI box has a hotter spark than OEM and retains the stock curve. It will replace OE# 30410-MN9-003 & 30410-MN9-000 and fit 1993-2021 XR650L. *CDI Boxes are not covered under the One Year Warranty.

Modern technology for the DR650s charging system. Mosfet style regulators produce less heat, are more efficient and last longer than old tech 'shunt style' regulators. Regulator is made by Rick's Motorsports, and includes a ProCycle adaptor bracket to fit into the existing space on the bike.

This regulator / rectifier is Lithium compatible.

Brand New External Ignition Coil

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• Highest grade lamination materials
• Spark plug cap(s) included
• All products shipped are tested by RM Stator

Contains all of the bearings and seals required to re-fit a wheel.

Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.

Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.

Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.

Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.

The rubber coated outside diameter creates an optimum seal at the hub.

Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.

Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.

Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.

Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.

Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.

Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.

The rubber coated outside diameter creates an optimum seal at the hub.

Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.

High Quality Replacement Wheel Bearings and Seals for your TW200.

Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.

Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.

Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.

Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.

Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.

The rubber coated outside diameter creates an optimum seal at the hub.

Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.

Did you go to an electronic speedo? SM Wheels? Something where you don't need the stock speedo drive? Then you need this to make up for that lost space and protect the bearings.

Quality rebuild kit by Moose Racing. Comes with everything you need to get your stock carburetor back in shape!

Genuine Keihin spring, washer, and oring for the fuel screw of FCR and FCR MX carbs.

Just the parts…
Fuel screw spring, washer, o-ring (fuel screw not included)

• Includes all necessary parts to replace OEM-style fuel mixture screw with an extended screw for easy tuning
• Kit includes extended mixture screw, O-ring, spring and washer.
   

Designed for use with stock engines using either stock or aftermarket exhaust and air filters.

• Provides a simple and affordable solution to carburetor tuning problems.
• Allows you to tune your bike for increased power and smoothness while retaining fuel economy.
• Includes a guide on how to install and use your jet kit to it's full potential.
• For a top quality installation we recommend adding an extended fuel screw and a set of replacement carb screws.

Twin Air Filter's patented design, high quality materials and superior construction deliver unbeatable performance and protection - and make Twin Air Filters the hands-down choice of more World and National Champions than all other filters combined.

The air filter is your engine's only protection against the elements, and your stock filter isn't up to the task. Replace it with a Twin Air-the #1 filter system proven on motocross tracks around the world.

Twin Air's fused layers of open-pore foam and fine inner foam trap even the smallest particles-without restricting airflow.

Looking for motorcycle road trip ideas? How about a Backcountry ride? Each of our backcountry motorcycle maps highlight the official Backcountry Discovery Routes (BDR) taking you off-road through some of the most spectacular scenery in the United States.

Made from medium carbon steel with hardened jaws. It features spanner pins and the jaws open up to 5" wide. It's ideal for holding clutch hubs, flywheels, gears, sprockets, etc. Made by Motion Pro.

• Features 8mm spanner pins
• Jaws open up to 5 inches wide
• Recommended for square tooth style clutch hubs
• Not recommended for v-groove or half round style clutch hubs

The genuine factory shop service and repair manual. This is the reference manual Honda dealers use in their service departments. It has all the necessary info to do maintenance or repairs to your Africa Twin CRF1100L.

Clymer manuals are the most user-friendly repair manuals. They are written for the do-it-yourself-er as well as the experienced mechanic by industry experts. Step-by-step instructions based on the complete disassembly of the machine. This manual in written to cover 90-94 models but nearly all of the information will apply to newer models also.

Extra protection for your motor! Strong magnet at the end of the plug picks up metallic flakes in your oil, protecting your engine!

CNC machined from 2mm 5052 plate, these will protect your cases in the event of a bad spill. Mounted using a high-quality red silicone adhesive, which you can select as an Optional Add On so you can mount them up as soon as they arrive. Below is a link to Installation Instructions with photos to help you get them done properly.

It may not surprise you that they are covered with HippoSkin™, their waterproof outer shell, and insulated with a generous layer of HippoFat™, a warm, flexible, closed cell foam insulation—both are designed to keep inclement weather away from your hands.

Sold in pairs.

Hand/brush guards are required for proper fitment and for safety reasons.

Hippo Hands go on and off in seconds and never require tools or hardware.

For Straight 7/8" handlebar

Keep your hands and controls protected from the wind and impact with Barkbusters VPS lever and wind protection handguards. Heat treated aluminum backbones with two mounting points of these handguards provide the strength needed to prevent a tip-over from ending your motorcycle ride. Impact resistant deflectors, available in multiple colors, provide protection for your hands from the wind and brush. Ride longer, more comfortably with Barkbusters VPS lever and wind protection handguards

Features:

• Two mounting points provide secure protection
• Full wrap guards
• Heat treated aluminum backbone bars
• Includes VPS left and right plastic deflectors
• Easy installation

What's in the box:

• Left and right aluminum backbone bars
• Inner and outer handlebar mounting hardware for both sides
• Left and right VPS plastic deflectors
• VPS deflector fastening hardware
• Left and right adjustable position wind extension deflectors
• Installation instructions

Universal Fit - May require modification to longer stock levers, a need for spacers, or use short levers on some models.

Not recommended for Africa Twin, T7, Himalayan, or V-Strom. Please see specific listings for those models.

For straight 7/8" handlebar

Protect your hands and levers with the Barkbusters Storm lever and weather protection handguards. Full wrap solid heat treated aluminum bars with secure two point mounts on each side provide strength while attractive and generous guards provide shelter from the wind and weather. Ride longer with the Storm handguards and complete mounting kit by Barkbusters.

Features:

• Two mounting points provide secure protection
• Full wrap guards
• Heat treated aluminum backbone bars
• Easy installation
• Tough and weather shielding Storm handguards
• Aluminum backbones are compatible with all Barkbusters deflector guards

What's in the box:

• Left and right aluminum backbone bars
• Inner and outer handlebar mounting hardware for both sides
• Left and right Storm plastic handguard deflectors
• Installation instructions

Universal Fit - May require modification to longer stock levers, a need for spacers, or use short levers on some models.

Not recommended for Africa Twin, T7, Himalayan, or V-Strom. Please see specific listings for those models.

These handguards come with mounts that will work on both standard and and oversize bars. The aluminum wrap-around bar is the biggest on the market with two large plastic shields that are also some of the largest available. The X-Factor hand guards offer great protection from the elements, especially during those colder months when you're trying to stretch out your riding season.

Works with 7/8" or 1-1/8" bars.

Universal Fit - May require modification to longer stock levers, a need for spacers, or use short levers on some models.

For Tapered 1 1/8" handlebar

Keep your hands and controls protected from the wind and impact with Barkbusters VPS lever and wind protection handguards. Heat treated aluminum backbones with two mounting points of these handguards provide the strength needed to prevent a tip-over from ending your motorcycle ride. Impact resistant deflectors, available in multiple colors, provide protection for your hands from the wind and brush. Ride longer, more comfortably with Barkbusters VPS lever and wind protection handguards

Features:

• Two mounting points provide secure protection
• Full wrap guards
• Heat treated aluminum backbone bars
• Includes VPS left and right plastic deflectors
• Easy installation

What's in the box:

• Left and right aluminum backbone bars
• Inner and outer handlebar mounting hardware for both sides
• Left and right VPS plastic deflectors
• VPS deflector fastening hardware
• Left and right adjustable position wind extension deflectors
• Installation instructions

Universal Fit - May require modification to longer stock levers, a need for spacers, or use short levers on some models.

Not recommended for Africa Twin, T7, Himalayan, or V-Strom. Please see specific listings for those models.
NOTE: Tapered kit will not fit Renthal Twin Wall or Barkbusters VSBar

For Tapered 1 1/8" Handlebar

Protect your hands and levers with the Barkbusters Storm lever and weather protection handguards. Full wrap solid heat treated aluminum bars with secure two point mounts on each side provide strength while attractive and generous guards provide shelter from the wind and weather. Ride longer with the Storm handguards and complete mounting kit by Barkbusters.

Features:

• Two mounting points provide secure protection
• Full wrap guards
• Heat treated aluminum backbone bars
• Easy installation
• Tough and weather shielding Storm handguards
• Aluminum backbones are compatible with all Barkbusters deflector guards

What's in the box:

• Left and right aluminum backbone bars
• Inner and outer handlebar mounting hardware for both sides
• Left and right Storm plastic handguard deflectors
• Installation instructions

Universal Fit - May require modification to longer stock levers, a need for spacers, or use short levers on some models.

Not recommended for Africa Twin, T7, Himalayan, or V-Strom. Please see specific listings for those models.
NOTE: Tapered kit will not fit Renthal Twin Wall or Barkbusters VSBar

Fits Moose and other aluminum hand guards

• Aerodynamic and stylish design
• Protect hands from brush, water and cold wind
• Simple installation
• Sold in pairs

• Made from strong and lightweight 4mm thick aircraft aluminum
• Protects vital engine parts from rocks and debris
• Custom fit to your specific bike model
• Oil drain hole for easy access
• All mounting hardware include

ProCycle Dashboard designed to power multiple electronic devices. It can also be used for accessory lights, heated grips or gear, whatever you like. You can also use the two pre-drilled holes to attach a RAM mount and place your phone or GPS unit on that while charging.

The dash panel is manufactured from mild steel and powder coated black. Also included are 2 weather resistant green LED rocker switches, and a voltmeter with two 4.2 amp weather resistant USB ports, a wiring harness with a built in 10 amp fuse/holder, and complete instructions. Everything you need to mount it and connect the outlets back to the battery.

Make your life a little easier by having a set of these in your toolbox. Designed to simplify installation and removal of clip-type master links. One tip is shorter and notched to be placed on the pin which allows the longer end to push the clip.

• PBR = press, break, rivet
• Innovative design will press, break and rivet 520, 525 and 530 chains with one convenient tool (not for use on 428 chains)
• Versatile design will remove chain pins, press master-link plates and rivet hollow nose and soft nose (quad stake) master link pins on O-Ring and non O-Ring type chains
• Easy-to-use design allows you to change tool functions by simply moving the position of the anvil block
• Indexing letters on movable anvil and body ensures correct tool configuration; simply line up the letter on the anvil to the letter on the body to get the configuration you need
• All components conveniently store on tool when not in use
• All steel construction with heat-treated components for strength and durability
• May be supported in a vise or held with included handle
• Great for the professional technician or DIY mechanic
• Compact and light enough to carry in a tool bag for trail-side repairs
• Patent Pending

Click Here for a quick guide on using this tool.

These great grip pads give you that improved relationship between you and your machine. You will feel the difference the minute you throw your leg over. Squeeze your tank and feel what a solid seat position is and does for you. They will assist in reduction of vibration, increase in control, and increase in comfort.

Will also help you cover wear spots on your tank whether it be the stock metal or a plastic tank. We tested had a couple sets of these on bikes with plastic tanks for at least 3 years and saw no signs of bubbling, peeling or coming off in any way.

This CNC cap will replace the stock gas cap on the stock tank. You do need some parts from the stock cap, so don't throw it away yet! It is not difficult and this kit includes the additional hardware required. Also included is a vent tube with a matching cap.

For use on STOCK TANK ONLY! 
This is NOT a locking cap.
Does not fit California models.

Polyurethane drive cushions for the DR. Polyurethane has a higher abrasion, cut, and tear resistance than rubber as well as much better resistance to chemical breakdown. This will offer longer life and better damping when compared to the stock rubber cushions.

A super compact shovel with several bonus features!

• Lifetime Warranty
• Compact and Portable Design
• Integrated Survival Features
• Durable and Versatile Cosntruction
• Hidden Tools Threaded in the Handles