Search Products

This high output stator will allow you to run brighter lights, heated gear, heated grips, etc. From ElectroSport

The WR Speedo is driven by the motor and is inaccurate up to 10% in the stock configuration. Change your gearing and it gets worse. This speedo calibration device is the smallest in the world and has the widest calibration range available. It has a simple plug and play installation that you do have to program, but easily done just using your current gearing. Change your gearing, easy to change your speedometer.

Other beneficial features include:

• Saves max speed, which can be recalled to your stock speedometer gauge
• Built in testing mode to ensure proper installation
• Works for vehicles which display MPH or KPH
• Ability to convert MPH to KPH, or KPH to MPH
• Ratio based correction in 0.1% steps, up to 99.9% + or -
• Weather proof design to protect against the elements
• 18" wiring harness (1.5 ft.)
• 3 year product replacement warranty
• Made in the USA!

Protects AC lights from high voltage blowouts in systems with no battery

These are the first batteries with built-in jump starting. They intelligently monitor their status, and just before going completely dead, puts itself to sleep with just enough energy to get your vehicle started again. Simply press the RE-START button located on the battery, start your bike and ride away.

These are an extremely lightweight (2.5 lbs.) high-powered Lithium-Ion replacement battery for motorcycles. These batteries offer the first Battery Management System (BMS) found on a powersport battery and includes low-voltage cut-off, over discharge, over-charge, and thermal protections with real time lithium-ion cell balancing. Use of a lithium specific charger to maintain the life of the battery is highly recommended.

Product Size is 8.4"L x 5"W x 2.2"H. If you need spacers, select the optional Foam Kit to pad the battery in the battery box.

Charges and maintains all 12 volt lead acid, gel and lithium iron phosphate (LiFePO4)/lithium ion polymer Non-RS/Non-BMS powersport batteries

Features:

• CONSTANT CURRENT CHARGE - If the battery voltage is over 10 volts, the charger will deliver a 2 amp charge until the battery reaches 14.2 volts.
• MAINTENANCE CHARGE - When the battery reaches 14.2 volts, the charger will automatically convert to maintenance mode. The charger will revert to charge mode when the voltage drops below a specified voltage.
• LOW VOLTAGE RECOVERY - If battery voltage is below 8 volts, the charger will apply a .2 amp charge to recover the battery, once the battery reaches 8 volts, the charger will apply a .5 amp charge, at 10 volts a full 2 amp charge is applied until the battery is fully charged.
• AUTOMATIC VERIFICATION STAGE - Charger automatically stops charging if the battery does not reach at least 10 volts after 2 hours of charging.
• SAFETY - Power is not passed thru the charging leads unless they are connected to a battery.
• LED indicator light shows charging status.
• Includes heavy duty clamps and fused ring terminal SAE adapter.

• Includes the lower shock bearing and all other parts necessary to rebuild the suspension linkage
• 52100 bearing steel and hard-plated spacers resist wear and rust
• Each kit includes the lower shock bearing, all the shafts, seals and spacers in the link, link arm and lower shock mount

Low friction 'triple lip' seal design. Oil seals last 3-4 times longer that OEM seals. Kit includes fork seals and dust wipers.

Seal profile is engineered to create equal pressure in each seal lip; equalized seal pressure creates less drag and longer seal life.

Patented MAX-LIFE has a coefficient of friction up to 3 times less than the OEM seal material

Triple-lip seal design

Dyno-tested to last 3 to 4 times longer than OEM seals

Directional ribs allow seal to be installed easily

Kits include fork seals and dust wipers

• Save time and money with this complete OEM quality fork bushing kit
• Kits include fork leg and slider bushings along with any needed snap rings, o-rings and copper washers

• Kit includes a pair of oil seals and dust seals; no bushings or other rebuild parts included
• Seals have been tested to over 1 million strokes in R&D development
• Every part meets or exceeds OEM quality standards
  
   

Genuine Yamaha fork seals and dust wipers.

Add a fresh set of inner and outer bushings for a complete fork restore.

Damping Rod style forks are notorious for being too harsh, too mushy and too easy to bottom. Gold Valve Cartridge Emulators remedy this problem by controlling the compression damping with a tuneable valve. The Emulator sits on top of the damping rod and is held in place by the main spring.

Simply put; Emulators make damping rod forks perform like well-tuned cartridge forks. Installation and tuning for any condition or rider preference is very straight-forward. 

Simple to install and completely tunable for all conditions and rider preferences.

Here is everything you need to upgrade your TW200 front suspension. Kit includes: Heavy Duty Fork Springs, Cartridge Emulators, Oil Seals, Dust Seals, and 10w Fork Oil. Just choose the spring rate you want and enjoy your TW even more!

Stock Spring Rate is .50 kg/mm. The .60 kg/mm springs are 20% stiffer than stock while the .70 kg/mm is 40% stiffer than stock.

Installation requires disassembling your forks and drilling out your damper rods.

Honda CRF3000L and Rally rear shock upgrade. The experts at Cogent Dynamics know suspension! A proven performance rear shock for your CRF300L or Rally for use under the most demanding conditions and on the roughest terrain worldwide.

Damping rates optimized to your specific needs, giving you the best ride comfort, traction and control. Frequency and velocity sensing valving works great over wide ranging conditions. Low internal friction. All CNC machined components for top quality and performance. Compact and rigid design with internal separator piston. Adjustable for spring preload and rebound damping. Fully serviceable shock is designed for the long haul.

 *Spring color may vary due to specification requirement and availability.

Cogent Dynamics build a fully custom suspension component, just for you. To best meet your needs, please spend a few moments providing us with your riding style (off-road / adventure, or street / commuting) and your approximate weight with gear and luggage in the comments during checkout. The information you provide helps them setup your suspension to most closely meet your needs.

• Repair kits include all the bearings, seals, shafts and spacers required for a complete rebuild
• Constructed from OEM-quality components at a fraction of the cost

A billet aluminum side-stand from PSR. This is the side-stand you want when you are using lowering-links.

Has many height settings from stock to 2" lower, a must have when lowering your bike. Available in anodized black.

The IMS Super Stock pegs are the perfect choice for both the daily commuter and the rider-in-training. Their mellow tooth design keeps you planted while preventing wear on your soles. They are also perfect for young riders who don't need or want a more aggressive option. 

Wider foot pegs for sure-footed comfort. 

17-4 cast stainless steel.

Pivot Pegz have set a new standard in footpeg performance and quality, and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty.

Pivot Pegz aim to build the best footpegs in the world and they really do perform as good as they look. Here's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever.

• Mega wide 60mm platform
• Widest and lightest pivoting pegs on the market
• Open design = less mud packing
• Unique multi-directional grip pattern
• Outstanding build quality
• Race proven design and durability

See below for extenders for these pegs to make them true ADV pegs!

Replace those narrow heavy OEM foot pegs with the ZETA Racing aluminum foot pegs. When you are on your dirt bike a stable platform when riding is important. The aluminum foot pegs offer a wider platform and the spikes offer more traction for your foot preventing you from slipping. Over all it offers more control on your bike. Made from CNC machined A2014 forged aluminum and stainless pins.

No repacking required. The LeoVince X3 Enduro is made with TIG welded stainless steel internals and aluminum outer shell. 

It features a semi-direct chamber design that is maintenance free. It's quiet too! Our own in-house testing showed an 84dB sound level using the USFS J1287 testing procedure. That is a bit louder than stock but significantly quieter than other aftermarket mufflers. 

The installed weight is approximately 8.5lbs and it includes a certified Spark-Arrester. 

This muffler requires a stock muffler joint gasket when used with either the stock headpipe or the FMF headpipe.

DG Performance exhausts help your engine breathe better, resulting in increased throttle response, power and torque.

The V2 Series Slip-On muffler features:

• Lightweight aluminum body
• Stainless steel inlet tube
• TIG welded components
• Great new look

Standard sound level is approximately 98 db and quiet core inserts are available separately.

This Lightweight Slip-On weighs approximately 5.5 lbs and bolts directly to the stock headpipe.

It is equipped with a US Forest Service-approved spark arrestor.

 The Powercore 4 spark arrestor muffler. FMF developed the Powercore 4 to increase the horsepower and torque throughout the entire power curve. Highest quality packing for long life. Removable spark arrestor included. Louder than the Q4. Approximately 99db stock or about 94db with optional Quiet Insert installed.

• Uses long-life muffler packing for increased packing life
• Forest Service approved spark arrester

The DG RST (Reduced Sound Technology) muffler is the quietest DG muffler and is designed especially for dual-sport machines (Just 84db @ 3200 RPM). A new baffle design dissipates sound waves reducing noise output in a very efficient manner. This new design also stretches out the time between muffler repacks. Included is a Stainless Steel mid-pipe, USFS Approved Spark Arrestor and a new Aluminum end cap.

• Oval muffler body with single turn-down polished aluminum end cap
• Maximized internal muffler volume for exhaust flow
• Straight, single-core baffle
• Can accept low-volume sound insert
• Large volume of packing material
• Straight baffle for ample flow
• Bolt-on design for easy installation

• Dual-muffler design exhaust system
• Achieves maximum performance, mass centralization, and rider usability
• Systems feature three-stage tapered headpipe for the best power gains, better throttle response and power delivery
• Vertical divider splits the exhaust gases more evenly for smoother flow to the mufflers for better mid-top power and throttle response
• Parallelogram-shaped muffler bodies increase muffler volume over the stock system for even crisper throttle response and reduced noise levels
• Systems meet AMA noise sound regulations right out of the box (AMA 2-Meter Max and Amateur 94 dB sound compliant)
• Muffler inserts are tunable to adjust power delivery and noise level

• The latest EVOLUTION of the popular LV ONE: aggressive sound and style
• Clean laser-etched Leo Vince logo in an innovative carved design (for the carbon fiber exhaust: bright aluminum die-cut high-temp resistant Leo Vince adhesive logo)
• Asymmetric design and high-tempiresistant full-carbon fiber end cap
• Impact-resistant sandblasted oval AISI 304 stainless steel sleeve – titanium look
• TIG-welded stainless steel front cup
• Adjustable full-carbon fastening strap
• Removable dB killer, weight savings and flawless installation

• Available in 52mm or 58mm lengths
• Kit contains two stainless steel exhaust swivel springs
• Free-floating mounting hooks to avoid breakage

The race-bred RS-2 exhaust has proven to be extremely popular among rider looks for a combination of performance and value. It enhances performance dramatically, provides an enviable exhaust note and offers the unmistakable look and sound of Yoshimura. RS-2 mufflers feature a straight baffle that leads to a single turn-down machined aluminum end cap.

All models have a USFS Approved spark arrester in a oval-shaped sleeve with a large volume of packing material.

• RS-3 Sound Insert for the Honda Monkey
• This new insert is designed to take the dB level down and fit perfectly with the RS-3 for the Monkey

Replacement front fender by Maier that will fit great on your TW200.

• All Maier bodywork is made of tough, vacuum-formed high-gloss polypropylene
• Drilling is required
• Colors are OE color matched

Note: The proper way to install this front is to install the stock fender bracket to the under side of new Maier front fender using stock screws and nuts.

Universal off-road front fender. Must be drilled to fit your mounting bolt pattern.

Replacement front fender by Maier that will fit great on your Kawasaki.

Available in 4 colors.

Sold in 6 packs

• Compatible with many air filter boxes. Easy to install by drilling 1’’ holes in airbox housing and snap fitting vents in.
• May be cleaned and re-oiled
• More air flow allows you to add more fuel to your intake mixture, increasing performance.
• 1" Diameter

Not legal for use on pollution controlled vehicles in the state of California.

Allows your bike to breathe much better giving you better response and performance.

• Breather Filter
• ProCycle Jet Kit which includes jets, needle, extended fuel screw, drill bits and Allen bolts to replace phillips (JIS) head bowl screws and detailed installation instructions
• Choose Twin Air, DT1, or K&N filter with ProCycle filter wrap
• OPTION - Twin Air breather filter (replaces standard breather filter)

The OEM foam secondary filter can deteriorate rather quickly. Once that happens, it can allow enough dirt into the engine to do significant damage. Replace your filter now with a high-quality foam filter from industry leader Twin Air.

This filter needs to be oiled like any air filter to work properly.

Only for bikes with the stock BST40 carburetor!

Unsurpassed in airflow, dirt stopping and overall performance. Adding a pre-filter to your intake system gives you extra protection from damaging contaminants.

Dyno and field tested, the Power Surge 6X will allow correction for humidity, temperature, air pressure, along with race fuels and motor modifications. The tuner adjusts in a matter of seconds in 6 zones, including an accelerator pump feature for more throttle snap response. The tuner can add or subtract fuel from the injection system. Conditions like rich or lean running, and stalling from flame-out at low revs can be corrected.

Most fuel injected systems are very lean in their stock configuration. This is good for economy and emissions, but not performance. This unit allows you to adjust the Fuel/Air (F/A) ratio without remapping the ECU and getting into complicated software programs. The PowerJet Fuel Controller allows you to adjust the fuel map from -4% to +10% by selecting one of 10 built-in settings (including stock).

The device works by measuring the outside air temperature very close to where the stock sensor is located and then adjusts the signal from the OEM air temperature sensor to the ECU to make use of the Air Temperature Correction factor that is built into the stock ECU. The ECU is told that the intake air is a little cooler than it actually is and it responds by richening the injection map very slightly. How much depends on your setting on the PowerJet. This will result in improved throttle response, especially if you have an aftermarket exhaust of any kind.

PowerJet is easily installed by plugging it in between the stock AIT sensor and the bike's wiring harness under the seat. This can be done very quickly as they are exactly the same plugs. Unplug the stock connection, plug in the PowerJet on each side. The PowerJet fits easily under the seat behind the battery as it is rugged and waterproof. PowerJet comes with a full one year warranty.

The Dynojet Auto Tune kit is an "add on" accessory that can be used with any of our Power Commander V’s. It connects to the PCV with a single cable and requires only a ground and +12 volt connection to be made to install. If your exhaust does not already have one, a "weld in" O2 sensor bung is included.

Once installed, the Auto Tune kit monitors the fuel mixture (by installing the included Wide Band O2 sensor in the exhaust). It then sends this information to the Power Commander V and automatically corrects it while you ride. Each map that we offer has preset Air/Fuel ratio values included that we find to be the best overall settings. This lets you simply plug in the unit and let it do the work.

Designed for use with stock engines using either stock or aftermarket exhaust and air filters.

• Provides a simple and affordable solution to carburetor tuning problems
• Allows you to tune your bike for increased power and smoothness while retaining fuel economy
• Includes a guide booklet on how to install and use your jet kit to it's full potential

All that you need to repair and inflate your tire on the road or trail.

• Padded nylon zippered carrying case easily stores inside fanny pack or tool compartment
• Everything needed to repair and inflate tire on the road or trail
• 4" inflator hose accepts threaded cartridges only
• Each cartridge produces 8-9 psi
• Made in the USA

Kit includes:

• 1 - large oblong patch
• 2 - medium size patches
• 3 - small patches
• Thumb buffer
• 0.50 oz tube of rubber cement
• 5 - 4" rubber insert strips
• Insertion tool with screwdriver handle
• Reamer/rasp tool with screwdriver handle
• 3 - 16 gram 3/8" threaded CO² cartridges
• CO² 4" inflator hose

CO² cartridges cannot be transported on an aircraft.

Here is a tool to help you remove a few links from a chain that is too long. A great tool to have in your tool box.

The head of the pivot pin you are going to remove must be ground down level with the side plate before using this tool to push it out. Failure to do that will cause damage to the tool that is not covered by any warranty!

A kit that includes an Axle Wrench combo for your bike with a 19mm for the front, and a 24mm for the rear. Just 7 1/2" long, it is long on leverage, but short enough to fit in even the smallest tool kit.

Also includes a pair of 'trail size' small tire irons.

No more fighting to keep the bead down while installing or repairing your off-road tires. The Bead Buddy holds the tire bead down in the drop center of the rim during tire changes making changes as easy as possible. Machined from tough 6000 series aluminum the Bead Buddy is light weight and compact enough for any tool pack. The Delrin securing thumb screw insures no scratches to your rims.

The Bead Buddy is NOT recommended for use with Bib Mousse tubes.

Motion Pro T-6 Combo Lever has a hex box wrench for your axle nut on one side and a perfectly contoured tire spoon on the other. Manaufactured from lightweight forged T-6 aluminum with a hard anodized finish. These beauties are just under 10 inches long and weigh only 3.5 oz. Available in a 12/13 combo unit and a 22, 24, 27 and 32mm hex ends.

This "pencil style" tire gauge has a brass head and a plated brass body.

90° angle allows for easy access to valve stems and easy reading.

5 to 50 psi measurement in one pound increments.

Very accurate.

Clymer repair manuals provides step-by-step procedures based upon the complete disassembly of the motorcycle. This hands-on experience combined with extensive research results in a manual that is both user-friendly and detailed. Hundreds of original photos and illustrations guide the reader through every job.

This Official 2001-up Yamaha TW200 Trailway Factory Service Manual provides repair, maintenance and service information for 2001-up Yamaha TW200 Trailway motorcycles. Most of the information is useful for the 1987-2000 models as well.

Need to remove your clutch assembly to get at that dreaded neutral safety switch? This holder is the quickest and easiest tool out there to get a grip on that hard to handle hub. Laser cut to the exact pattern that EBC makes their clutch plates from, it makes loosening and re-tightening the clutch nut easy. All of that and no worries about doing any damage to your expensive clutch hub.

Bottom line, if you have to hold your clutch hub to remove it, there is no better way to do it.

Reproductions of the original DR650 factory turn signals. Save a bundle compared to the $70+ each cost of the OEM signals. The wire pigtails plug directly into the factory harness. No cutting or splicing necessary. Choose original style amber lens or clear lens with amber bulb.

If you just installed aftermarket LED turn signals or an LED integrated tail light and your turn signals are flashing way too fast, or perhaps simply staying on completely, you're at the right place to find the solution! The TST Gen2-SK LED Flasher Relay fixes what we call "hyperflash". It slows the flash rate down to a pre-set 85 cycles per minute but can be sped up or slowed down using the adjustment dial located within the unit so you can get the exact speed you are looking for. The plug-and-play installation means that you don't need to splice in any load balancing resistors that generate unnecessary heat and require splicing into your stock wires. Simply remove the stock relay and install your new TST relay and your wiring job is done. It's that simple!

• Slows turn signal flash rate down to an adjustable 85 cycles per minute when turn signals are experiencing hyperflash or stay on continuously
• Adjustable turn signal flash rate enables you to speed up or slow down the flash rate to fit your preference
• Plug and play installation meaning no cutting, splicing, or soldering
• Replaces the stock relay and fits like OEM
• No need for cumbersome and heat-generating load balancing resistors
• Flexible relay housing enables easy access to the flash rate adjustment dial inside of the relay unit

Please make sure your bike uses a 2-pin relay for the signaling system. If your bike has hazard lights it may need the 4-pin relay. Please also note the pin configuration and make sure it matches what is on your bike. It is very important to verify fitment before making your purchase.

There is a lot of technology packed into this tail light/fender eliminator kit. You have programmable turn signals and Safety Brake Pulsing both built into this product.

You can enable or disable the safety brake pulsing feature.
This kit includes only the highest quality components, including the pre-installed 12oClockLabs processor board, which is made in the USA.

• Plug and Play
• 7 Different Programmable Turn Signal Patterns 
• Safety Brake pulsing built in (Can Enable or Disable)
• Superbright LED's; For excellent brightness, even in direct sunlight
• License Plate Light built in
• License Plate Bracket fits the common USA license plates, sloted for maximum plate compatibility.
• Includes Mounting Hardware
• Saves about 2 lbs over the factory tail light setup
• Made In the USA

We recommend a "Fixed Rate Flasher" unit for use with this kit. When you install aftermarket signals it changes the load on a factory signal system.

This kit does not include parts to mount aftermarket turn signals. The pre-installed processor board allows the turn signals to be integrated in to the tail light.

Yoshimura has always been synonymous with quality craftsmanship, precision fitment, and impeccable quality. The Fender Eliminator Kits are no exception, and they are sure to give your motorcycle the sleek race look that every rider craves

Features:

• Precision laser-cut stainless steel bracket tucks discreetly under the tail section of the motorcycle
• Black anodized CNC machined light housing with laser-etched Yoshimura logo
• Light housing contains four bright LED lights
• Black anodized aluminum license plate frame with silk screened Yoshimura logo
• Stainless steel hardware included
• Compatible with aftermarket turn signals when combined with Universal turn signal bracket kit (sold separate)

Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a more plush and active ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.

These features combine to offer a custom seat feel, and provide greater enjoyment and increased range on a long commute, or Dual-Sport ride!

Seat Concepts seats are constructed using a foam material that is higher quality than OEM seat foam. Their proprietary formula is plush, while still offering the necessary amount of support. Their unique comfort and shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.

These great features combine to offer you a custom seat feel, and provide greater enjoyment and increased rangefor long commutes, or Dual-Sport rides!

The Complete Seats come assembled with an high quality aftermarket pan and ready to ride.

Superior Filtration:

This should be the last oil filter you will ever buy. Made from laser cut, medical grade, 304 stainless steel micronic filter cloth, this filter provides 200% more filter area than other filters in many cases. Most good paper filters will pass particles in the 90 to 95 micron range, and some tested, as much as 300 microns. Sand is about 125 microns and a white blood cell approximately 25 microns. Scott's stainless filter catches items down to 35 microns "absolute". The pleat seam is welded, able to withstand up to 600 degrees, not glued, like paper filters.

New starters that are manufactured to meet or exceed OEM specifications. Pull out your old starter, put in this new one and go riding. These units are built to provide a longer life than the OEM unit with these features:

• The armature is insulated for rust and corrosion protection
• Rubber seals on the top and bottom of the unit ensure a dry operation
• 90/10 copper bushings
• Extended shaft replaces long or short shaft OEM starters

The long awaited Wide Ratio Transmission from Nova Racing. Now you can have your trail gearing without giving up your highway gearing.

Both sets are lower than stock in 1st and 2nd gear and taller than stock on 3rd thru 5th gears. Not only will Nova give you better gear ratios but the high quality components will shift smoother and engage more solidly. The tables below show each gear ratio and the original OEM ratios for comparison.

To help put the ratio changes into perspective switching from the OEM 15T to a 14T sprocket lowers the gearing by 7.1% in all gears. Switching from a 15T to a 16T raises the gearing by 6.6% in all gears.

Complete set of friction plates, HD springs and steel separator plates prevent premature driven plate wear, oil muddying and loss of stack height. Built with swaged aluminum carriers that spread the load on the clutch basket and prevent clutch basket "dogging". Anti-swell, alloy impregnated heavy-duty facings for smooth clutch action. Allows modulation, unlike paper clutches which tend to snatch. Don't forget to add a fresh gasket.

A pair of factory OEM o-rings for the valve covers. Your valve cover o-rings live in one of the hottest parts of the engine and have a pretty short life. Replace them on your next valve adjustment to prevent oil leaks.

Time to adjust your valves? Here are the O-Rings that fit in your Valve Covers on your Yamaha. Keep the oil inside your motor and grime out! This kit includes both O-Rings. Be sure to grab the feeler gauges and a special wrench to aid in adjusting your valves.

Includes all necessary top quality gaskets, and seals for engine rebuilds.

• Meet or exceed OEM specifications
• Highest quality materials
• Rubber coated spring steel head gasket, and soft steel base gasket

Top End Gasket Set is designed for a piston replacement job and includes:

• Head Gasket
• Base Gasket
• Intake Gasket
• Exhaust Gasket

Stock bore replacement pistons from Wiseco. You have your choice of the standard compression ratio of 12.2:1, or a high-compression ratio of 13.5:1.

This high-compression kit will run perfectly with standard pump Premium.

Kits include piston, rings, wrist pin and circlips.

Raises compression from stock 9.5:1 to 10.5:1 for more power and snappier response. Highest quality Wiseco pistons are forged in the USA. Fits the standard size stock bore.

  As with any engine or exhaust modification, you will need to re-tune your fuel delivery system for optimum performance.

ProCycle 440cc BIG BORE 89mm KIT 2 With Cam Complete kit with 11:1 Wiseco piston (with rings, pin & clips), big bore cylinder sleeve, HotCams stage 3 camshaft and top end gasket set. You will have to have the larger sleeve installed in your cylinder.

The Front Rack gives a lot of options for functionality.

CycleRacks are made out of Schedule 40 11/16 black steel pipe, bent in a press, and welded together in a jig.

All of their products are 100% made in the USA. If the rack is ever broken for any reason, CycleRacks will replace it for free, you just pay the shipping.

Every backcountry adventure-seeker needs a handful of these multi-purpose straps with virtually unbreakable fasteners. Each pair of stretch polyurethane Pronghorn Straps™ feature stamped aluminum buckles sheathed for scratch protection with arrows that line up for easy fastening. Each buckle prong holds the strap in place for pre-fitting and easy chaining of straps together.

Available in color-coded 18-, 25- and 32-inch lengths and marked by size, you’ll find a million uses for Pronghorn Straps—motorcycle, sled, snow bike, 4×4, ATV, UTV/SXS—and so much more!

We worked with TechSpec to have them make custom tank grip pads that look great on both Acerbis (5.3 and 6.6 gal.) and IMS tanks. These pads not only cover those ugly scuffs, but give great knee grip to the slippery plastic.

These have been tested on two of our shop bikes for over 3 years, they did not bubble or peel off in any way.

Acerbis fuel tanks were designed to provide additional fuel capacity without sacrificing ergonomics, and are the perfect choice for the rider trying to increase the range of their machine. Constructed of impact and abrasion resistant Polyurethane, Acerbis fuel tanks are durable, stylish, and will provide years of service.

* Will not fit 2017 Model

• Tread pattern yields traction in hard terrain
• Built-in rugged tread blocks feature Staggered Step design, a step-down feature to provide rigidity in the contact patch to enhance stability and handling
• Wrap-around lugs on the tire's edge to protect the tire from sharp rocks and provides additional off-road traction
• New compounds to deliver the perfect balance between road and off-road performance with focus on delivering class leading mileage performance
• Deep grooves excel in wet weather conditions
• T-rated for speeds up to 118 mph
• Tires are tubeless, however if mounting on rims that require a tube (i.e., spokes) the appropriate tube may be fitted
• Blackwall
• Fits popular large and small displacement machines.

Standard Duty tubes are made with seamless construction from natural rubber with heavy duty valves. Great replacements for stock tubes and perfect as spares to carry on your bike.

• 17" tube works with 110/90, 120/80, 120/90 (4.00 to 4.25) tires
• 18" X 3.75 tube works with 110/90, 120/80, 120/90 (3.75 to 4.25) tires
• 18" X 5.10 tube works with 110/90, 120/90, 130/80, 130/90 (4.00 to 5.10) tires
• 19" tube works with 100/90, 110/90 (3.60 to 4.10) tires
• 21" tube works with 90/90, 90/100 (2.75 to 3.00) tires

Don't forget a Rim Strip. New tubes deserve new rim strips.

ULTRA HIGH-PERFORMANCE HYPERSPORT TIRE

Avon's technological design and construction gives ultra high-performance handling and stability characteristics.

Multi-compound rear tire for all around performance.

Tubeless and V rated (for max speed of 149 mph)

These handguards come with mounts that will work on both standard and and oversize bars. The aluminum wrap-around bar is the biggest on the market with two large plastic shields that are also some of the largest available. The X-Factor hand guards offer great protection from the elements, especially during those colder months when you're trying to stretch out your riding season.

Works with 7/8" or 1-1/8" bars.

X-Factor guards may require you to cut your lever ends down, or use short levers.

FUZION guards feature the ultimate in hand protection with a unique design and flexible yet durable material. 

The expanded coverage area sweeps back toward your hand significantly increasing coverage making it perfect for cold, muddy or wet conditions. 

The FUZION features a unique two position mount and is constructed of molded light-weight closed-cell AEPE foam, which is crush-proof, water proof and extremely durable. 

The FUZION will work great for road of offroad riding, where wind deflection is important, and or bouncing off trees is a common occurrence. 

Kit includes mounts. Optional replacement mounts available.

Safeguard your Yamaha XT250 with T-Rex Racing's premium engine guard crash cages designed for serious off-road protection. These heavy-duty steel crash bars create a protective barrier around your engine and frame, preventing costly damage from drops, crashes, and trail obstacles. 

Custom-engineered for XT250 models, these bolt-on engine guards feature powder-coated finish for corrosion resistance and maintain ground clearance for optimal performance. 

Includes all mounting hardware. Essential protection for adventure riders, trail enthusiasts, and dual-sport motorcyclists who demand reliable crash protection for their Yamaha bike.

• Essential protection for many late model adventure touring bikes
• Precision built for exact fit installation
• High Strength 25mm diameter powder coated aluminum construction
• All necessary hardware included

• Provides flat surface on both sides of the frame for better bike holdings.
• Made of 2mm thickness 5000 grade aluminum for durability.
• Hairline processing surface finish.
• Comes in a pair, bolt on design, and no modification required for installation.

• CNC’d and formed from aircraft grade 5052 aluminum
• Reinforces radiators to help prevent costly radiator replacement
• CNC’d billet bracket system incorporates rubber vibration isolators (most models)
• Lightweight, custom fit, tuck in cleanly behind radiator shrouds
• Simple bolt-on
• Mounting hardware included
• Made in the USA

CNC’d and formed from aircraft grade 5052 aluminum. Covers and protects the rear brake master cylinder.

These quality sprockets are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.

Chain guides experience degradation over time as a result of chain friction. To ensure optimal performance replace worn components with genuine Honda parts.

Chain guides experience degradation over time as a result of chain friction. To ensure optimal performance replace worn components with genuine Honda parts.

K&L® shims exceed the maximum of the Apparent Rockwell Hardness "C" scale. Shims average 47.0 compared to the 46.0 maximum.

This kit fits multiple brands and models, please verify correct size for your model before purchase.

It may not surprise you that they are covered with HippoSkin™, their waterproof outer shell, and insulated with a generous layer of HippoFat™, a warm, flexible, closed cell foam insulation—both are designed to keep inclement weather away from your hands.

Sold in pairs.

Hand/brush guards are required for proper fitment and for safety reasons.

Hippo Hands go on and off in seconds and never require tools or hardware.

No Toil rim grease is a high viscosity, non petroleum based compound specially engineered to provide the ultimate filter rim to air box seal. 

Designed to withstand temperatures up to 300° F, it remains waterproof and dust-proof, keeping damaging dust and water from being drawn past your filter

• Biodegradable
• Non toxic, Waterproof
• Easy cleaning in seconds with water and No Toil cleaner

Direct replacement OEM front brake cable for TW200 with drum brakes.

Repair kit for your rear disc brake caliper.

This rotating shift tip provides 6 different positions, offer more sensitive shift position adjustment. Shift arm is made of A2014 forged aluminum for durability and is black anodized. Foldable shift tip is made of CNC aluminum with knurled finish for better shift grip. Replacement shift tips and tip mounts are available.

The Magura Hymec Hydraulic Clutch system. Simply remove the stock perch, lever and cable and bolt this in its place. This system replaces the stock cable with a small lightweight hydraulic system for improved clutch control, easier operating pressure, a constant pressure point and smoother actuation. Developed over many years and tested under the toughest conditions possible in the off-road motorcycle world.

You will have to bypass your clutch safety switch to use this unit.

Never hurts to have a bit of the Margura specific Blood Red hydraulic fluid as well.

These tips are for the Warp 9 Shift Levers only. 

These are held to the cast Warp 9 lever with a pin and e-clip making them easy to change out. Includes new pin and e-clip in case you lose yours.

You can also order just a new pin hardware kit which comes with new pin and clip.

• The new 3rd generation Motion Pro Revolver variable rate throttle system is here!
• Innovative reel changing system lets you tailor the throttle rate to your preference and riding conditions
• 5 different reels provide perfect throttle response for any condition. Use smaller reels for slower throttle rate and larger reels for faster throttle rate. Included cam reel provides progressive throttle response preferred by some riders
• Slim REV3™ throttle housing allows more room for lever clearance and adjustment to throttle housing position
• Improved throttle stop provides greater strength and durability
• Snap together elbows makes it even easier to install and change reels
• Cable boot keeps dirt and dust out for reliable and smooth operation
• REV3™ off-road kits are compatible with the new Motion Pro DirtControl™ V2 Lock-On grips and ODI Lock-On grips
• Billet aluminum inline cable adjusters ease installation and adjustment
• Lower section of cables use 5 mm housing with PTFE liner for reduced friction, increased routing flexibility and lighter weight
• Upper section of cables use 6 mm housing to provide solid support of adjusters
• Simple to install and maintain
• Patented

Kit includes:

• REV3™ throttle assembly with throttle tube (REV3™ off-road kits include the unbreakable Titan Throttle Tube™)
• Motion Pro REV3™ black vinyl cables specifically designed for your bike
• REV3™ sportbike kits include Motion Pro RoadControl™ grips
• Four interchangeable round reels: 35 mm, 40 mm, 45 mm, 50 mm
• Progressive cam reel - Sportbike kits include road race profile cam reel (orange)

• Powercore silencers give your ride a deep works-like tone while providing optimum, dyno-tuned performance
• Silencer body is constructed of 6061-T6 grade aluminum with machined mounts and a clear anodized finish to bring out the shine

Motocross brake rotor featuring ultra lightweight radically profiled contours for great looks, great self cleaning and brake performance. Made with tough and durable heat treated stainless steel. Heat treated to perfection and then diamond ground to micron accurate surface finish and parallelism and will deliver great brakes that perform well and last.

The DR650 is rather hard on the cush drive rubbers. Replace these any time you feel excessive play in the sprocket carrier hub. Excessively worn dampers can cause the cush hub bearing to fail - which will ruin your sprocket carrier. Sold as a set of 6 rubber dampers.

Replace these any time you feel excessive play in the sprocket hub.

Excessively worn dampers can cause the cush hub bearing to fail - which will ruin your sprocket carrier.

Sold as a full set.

Lost your side panel hardware? You aren't the first! We've got replacements. Two side panel screws, two special washers and the rubber insert that protects the side panel from the muffler.

The Complete Doohickey Replacement Kit features the Doohickey supplied by Eagle Manufacturing, a torsion spring accompanied by a drill bit, a generator cover gasket, and an exterior cover gasket. Additionally, it includes all necessary components for rotor removal, along with a replacement bolt for reassembly.