Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm. Lo-pegs are down and back 1/4".
2 high-quality bushings per set. They recommend changing bushings every 40 hours or at least once a year to get the best performance out of a set. If you are on an Adventure Bike and are doing a lot of road miles they recommend swapping out bushings once a year to ensure that you get the most vibration dampening of the bushings.
Every new set of pegs comes with a 90A bushing installed. This is a medium flex rating.
80A is the softest and 95A lock-out is the stiffest and has the least amount of flex.
The bushings act like the suspension on your bike. With bushings, there are a couple of things to think about. The more firm the bushing the more durable and longer it will last. They use a durometer, a hardness scale 0 being the softest and 100 being the hardest. They don't go below a80 because they found that durability isn't great below this but have tested as low as a60 bushings. A bigger person that rides enduro-style terrain might want an a96 or a98 rated bushing. A lighter person might want the opposite but in the end, it comes down to personal preference.
The bushings are high quality yet inexpensive (they achieve this because they use skateboard bushings that are already developed and produced in massive quantities around the world) and a wear item designed to be replaced each season or depending on how hard or often someone rides.
For use on Motion Factory Foot Pegs Only
Pivot Pegz have set a new standard in footpeg performance and quality and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty.
Pivot Pegz aim is to build the best footpegs in the world and they really do perform as good as they look. Here's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever!
Pivot Pegz have set a new standard in footpeg performance and quality and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty. Pivot Pegz aim is to build the best footpegs in the world and they really do perform as good as they look. Here's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever!
Tapered roller bearings provide decreased maintenance, less wear, smoother operation and longer life.
This set of high quality replacement steering stem bearings includes:
We start with a silver Excel or Sun rim and an OEM hub, then tie them together with Buchanan's heavy gauge stainless steel spokes. Rims and spokes are precision machined for a perfect match to your bike.
Our pro shop then laces and trues your wheel to perfection, giving you the highest quality custom wheel available.
Add a tire to your wheel order and we will throw in a tube and mount and balance it at no additional charge.
We start with Silver Excel or Sun rims, Warp 9 billet hubs, and Buchanan's heavy gauge stainless steel spokes. Rims and spokes are precision machined for a perfect match to your bike.
Our pro shop then laces and trues your wheels to perfection, giving you the highest quality set of custom wheels available.
Add tires to your wheel order and we will throw in tubes and mount and balance them at no additional charge.
Rear wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.
Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.
Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.
Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.
Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.
The rubber coated outside diameter creates an optimum seal at the hub.
Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.
| Description | QTY per Kit |
| Ball Bearing | 3 |
High Quality Replacement Wheel Bearings and Seals for your TW200.
Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.
Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.
Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.
Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.
Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.
The rubber coated outside diameter creates an optimum seal at the hub.
Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.
| Description | QTY per Kit |
| Ball Bearing | 2 |
| Seal | 1 |
Quality steel sprockets and EK SRO6 O-ring chain. We put them together to make a complete, affordable kit. Chain comes with clip type master link.
Individual 14T, 15T or 16T front sprockets.
JT Sprockets are made from the latest generation of computer design and control metal cutting equipment for maximum durability. Front sprockets are made from chromoly SCM420 steel alloy. All sprockets are heat-treated and hand-finished to meet or exceed the highest possible quality standards.
We recommend using the Rear Sprocket Bolt Kit when installing most aftermarket sprockets on your TW.
Stock gearing uses a 45 tooth rear sprocket
The 50 tooth rear sprocket will give you much lower gearing for off-road use. You will need a longer chain for this rear sprocket, please order the 130 link chain to fit with this larger sprocket, it may need to be shortened to fit correctly.
High Quality chain. You'll need to cut to fit your sprocket combination.
Non O-ring, Clip Style Master link
High Quality chain. Will need to be cut to fit your sprocket combination.
Lower friction and longer life. X-rings have twice the sealing ability as compared to o-rings. They do a better job of keeping the lube in the links and the dirt out. DID VX chains have a reputation for being the best chain you can buy for dual sport riding. DID VX chains come with rivet type master links.
High Quality chain. Will need to be cut to fit your sprocket combination.
All of these chains come with a clip type master link.
High-quality DID chain and steel sprockets for 2002 & later TTR125s.
This an OEM replacement nut for your front sprocket.
Fully encloses the chain to guide it onto the rear sprocket. Stainless steel hardware, anodized aluminum plate, and plastic buffer for low friction and noise. Saves expensive engine cases.
The DG RST (Reduced Sound Technology) muffler is the quietest DG muffler and is designed especially for dual-sport machines (Just 89db @ 3200 RPM). A new baffle design dissipates sound waves reducing noise output in a very efficient manner. This new design also stretches out the time between muffler repacks. Included is a Stainless Steel mid-pipe, USFS Approved Spark Arrestor and a new Aluminum end cap.
You may want to consider a new exhaust gasket that goes between the header and the muffler.
The RS-2 is a potent and versatile design that evolved from the original TRC, engineered to provide increased power and power delivery. With a different pyramidal shape that features increased volume, the RS-2 is a quieter system with a larger core - and it offers the added bonus of outstanding performance in a value-priced package.
Reduce exhaust leaks with this new OEM exhaust gasket. This gasket goes between the header pipe and the cylinder head.
We recommend Anti-Seize on exhaust fasteners.
These brake fluids are motorcycle approved DOT 4 brake fluid, and is specially formulated to exceed all DOT 3 & DOT 4 specifications. What this means to you is exceptional resistance to vapor lock and maintaining consistent lever feel during extreme brake use.
Easily turn your blinkers into additional running lights and brake lights (rear) for added visibility.
White light in the front and red in the rear. Rear red running lights and bright red brake lights. You can omit the running and brake lights if you wish and still have the best blinkers on the market.
Dazzling bright Amber blinker functions.
Everything comes in a spring-loaded stock designed to keep it safe from those unexpected tip-overs, crashes, or encounters with brush and trees. They’re flexible enough to bend 360 degrees, yet tough, durable, and almost impossible to break!
If you have a single indicator light for the blinkers that is not built into the display and is not LED you will need the diode kit (AKA DR650) If it is built into the speedo display it should not require the diode kit.
Available in a generic kit with Bullet connectors supplied. Great for your DR or almost any other bike with a single post blinker setup. These will work well on bikes that use a flasher, but you might have to add the female side of the connectors that are included in the kit.
Not for Yamaha T7, see model specific listing
This kit is not just a bulb, but an entirely new LED specific headlight! A specially designed adjustable steel mounting bracket replaces the stock unit. Included is a wiring harness and all the required hardware to make this installation quick and easy and entirely plug and play. No cutting, no drilling, no wiring modifications are necessary. The headlight features separate low and high beam projectors in a custom headlight shell designed specifically for this LED bulb.
Now available with a black chrome reflector!
Check out the images below for stock vs. LED patterns and brightness images.
Fits '87-'07 only
This replacement lens has a clear panel on the bottom to illuminate your license plate.
Allows you to bolt your license plate directly to the rear fender.
Does not fit Australian DR650.
Use these brackets to mount your light weight auxillary lights or turn signals. They will bolt directly on to the DR650 lower triple clamp bolts. This makes for a clean 'tucked in' installation. Sold in pairs.
For a top notch rebuild or re-valve of your rear shock use this high quality replacement seal head.
These Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. No disassembly of your forks, no drilling of damper rods. Just change the oil to 5w and install the DDCs under the springs and hit the trails.
Stiffer fork springs are required to realize the full benefits of the DDCs. .42 kg/mm springs are the springs recommended for just about anybody out there. Please call if you have any further questions.
The DDCs are not recommended for use with progressive springs.
The DDC Install/Removal Tool which makes installation that much easier.
These springs are custom wound specifically for the XT225. Stiffer than the .36 kg/mm stock springs, these will make your front perform significantly better. Combine them with the Cogent DDC's and you will be very happy with the results. Sold as pairs.
Included in this kit are .42 kg/mm fork springs, Cogent DDC (Drop in Damper Cartridge) performance cartridges and two bottles of 5w fork oil.
Custom developed by BBR Motorsports for the ultimate upgrade for mini four-strokes. Sized perfectly for fast/aggressive adult mini riders. This is the most important upgrade you can make for an adult sized rider. The stock suspension is too soft for most adults.
This complete fork upgrade kit includes stiffer fork springs and Race Tech cartridge emulators, as well as a set of top quality fork seals and fork oil to complete the job. Everything you need to transform your mushy stock forks into suspension that really works.
You can select from various straight rate springs to customize the package to your needs.
Seal profile is engineered to create equal pressure in each seal lip; equalized seal pressure creates less drag and longer seal life.
Patented MAX-LIFE has a coefficient of friction up to 3 times less than the OEM seal material
Triple-lip seal design
Dyno-tested to last 3 to 4 times longer than OEM seals
Directional ribs allow seal to be installed easily
Kits include fork seals and dust wipers
Sized perfectly for adult back-yard racing or fast/aggressive mini riders. This is the most important upgrade you can make for an adult sized rider. The stock suspension is too soft for most adults and aggressive kids. Fits stock shock.
CycleRacks are made out of Schedule 40 11/16 black steel pipe, bent in a press, and welded together in a jig. All of their racks have the same platform, 18" wide by 12" deep. Includes lower mount hardware.
All of their products are 100% made in the USA. If the rack is ever broken for any reason, CycleRacks will replace it for free, you just pay the shipping.
PMR side utility racks are great for strapping down your soft luggage and keeping it off the rear plastics and exhaust pipe, while adding plenty of new tie down points for any luggage you have on your seat or tail section. They also add an enhanced level of security and strength to the rear end of your motorcycle in the event of a tip over or crash.
Sold as a pair. Easy to Install
Precision Motorcycle Racks strongly recommends these side racks be used with their Top Rack because the racks use each other to mount properly. They were never intended to be used by themselves without the rear rack.
If you are going to mount these side racks without the use of their top rack please select the extra hardware kit option that includes 2 brackets, 2 steel spacers, and an extra hardware kit that is required for proper installation.
These side racks will not play nice with any other brand rear rack, and installation without their top rack will prove to be quite difficult.
Nomadic Rack for the TW200. CNC laser cut from 3/16" 5052 aluminum with a large 12 x 10-7/8 mounting surface area. Sand blasted and then powder coated black to give it a shot peened look. This rack is an easy installation with a 4 point mounting system with no modifications required. There are multiple strap slots for securing gear bags and cargo. Doubles as a grab handle or tow bar. Is compatible with RotoPax mount. All hardware and instructions included.
You may purchase just the rack or you can order the Rack with the RotoPax Mount. If you really want it all, you can order the Rack, Mount and a Fuel or Water Container.
Their rear racks are great for adding the extra storage needed for your next adventure. They are the perfect size for a backpack or small duffel bag. Their steel racks are built to handle any riding style you throw at them, now Rotopax ready! This is the ENDURO Series XT225 Serow rear rack which measures 10 inches wide and 12 inches long.
Easy to Install
Simple, lightweight rack made from rugged 1/8" 5052 Aluminum, with a rigid 5-point mounting system.
Low profile allows for easy seat removal.
Features:
Note: Placement of this top rack does require removal of the stock tool bag.
Lite:
Motion Factory Racing patented Flex-Mount Footpeg System provides superior grip and allows your foot to flex forward and back with the movement or your motorcycle.
One of the key features of Flex-Mount Footpegs is their unique flex-mount design. This design allows the footpegs to absorb shocks and vibrations, reducing fatigue and improving overall comfort during long rides. Additionally, the adjustable height and angle options ensure a personalized fit, allowing you to find the perfect riding position for maximum control and stability.
The bushings act like the suspension on your bike. With bushings, there are a couple of things to think about. The more firm the bushing the more durable and longer it will last. They use a durometer, a hardness scale 0 being the softest and 100 being the hardest. They don't go below a80 because they found that durability isn't great below this but have tested as low as a60 bushings. A bigger person that rides enduro-style terrain might want an a96 or a98 rated bushing. A lighter person might want the opposite but in the end, it comes down to personal preference.
They put an a90 bushing on all new mount setups so people can get a good feel for their mid range option. The bushings are high quality yet inexpensive (they achieve this because they use skateboard bushings that are already developed and produced in massive quantities around the world) and a wear item designed to be replaced each season or depending on how hard or often someone rides.
Complete mount system includes:
They designed their hardware to bend rather than break in a significant impact. A wrench or adjustable wrench will quickly and easily bend the bolt back straight. Please avoid using a hammer. A little leverage from a long-handled wrench or pipe will do the job. The whole system is rebuild-able and serviceable.
Revolutionize your riding experience with Swiftkicker.
An adjustable kickstand for your motorcycle. Swiftkicker is built for offroad motorcycles, dual sports, and dirt bikes. Designed with the idea in mind that motorcycles should be able to take you anywhere, the Swiftkicker motorcycle kickstands help you do just that. You can set the length to anywhere in a six inch range of travel so you can stop anywhere without having to worry about having an even surface to park.
With just a flick of your toe, you can adjust the kickstand to the desired height, park your motorcycle, and be on your way.
No longer will you have to search for a rock or piece of wood to prop your motorcycle up with, or even worse, coming back to your bike to find it has tipped over from unstable ground.
The Swiftkicker is 100% manufactured in the USA from the highest quality components.
The billet 6061 head and the hard anodized tube are significantly stronger than the stock stand. An oversized foot will assure that the end of your stand stays where it belongs, rather than eight inches underground with your bike lying on top of it. The design is trail proven in the harshest possible conditions. Because nothing is indestructible, any of the kickstand components are replaceable at a lower cost than purchasing an OEM kickstand.
Measured from the center of the pivot to the bottom of the foot.
This great tire gauge measures from 0-100 psi.
Has a back-lit display, and a front light to help locate the tire valve.
Select from psi to kPa units of measurements.
Replaceable batteries and automatic shutoff
CE approved and CARB compliant.
Very accurate.
This new unit from JNS will protect your cases from the damage caused by a thrown chain, and will also keep your pants, boots or foot safe from your countershaft sprocket.
The case saver portion is laser cut from 0.25" aluminum and then has the 0.19" aluminum countershaft sprocket cover welded to it and the entire unit is powder coated black.
All the mounting hardware is stainless steel with machined aluminum spacers also included.
If you have a 16t front sprocket, mounting modification may be needed to fit. Install the case saver on the bike without the top spacer and bolt. This provides a little extra wiggle room. Add the top spacer and bolt after the bottom bolts are loosely threaded.
Universal off-road front fender. Must be drilled to fit your mounting bolt pattern.
ProCycle Plastics (formerly DSA) Rear Fenders include LED tail/brake light and license plate holder. Vacuum molded, these parts are a design improvement over stock.
Freshen up the look of your TW. New Plastic in Black or White. Includes Rear Fender, Side Panels, Headlight Cover, and Front Fender.
Choose a Kit with OEM Front Fender or after market SuperMoto fender.
SuperMoto fender kit includes our High Mount Fender Bracket!
The Rally windscreen from Parabellum is the perfect protection from wind and debris without sacrificing technical off-road capabilities. This is an upright rally type windscreen that looks aggressive and performs well under all types of riding. Designed primarily for the off-road / dualsport enthusiast, this shield keeps pressure off the rider's chest while commuting from home to adventure and back.
This windscreen mounts securely to the three stock windshield holes as well as the two side cowling mounts. The shield is 14 inches tall, 13 inches wide at the bottom narrowing to 11 inches at the top. Made from 3/16" military aircraft grade cast acrylic.
Parabellum LTD. has continued the highly demanded Rally Shield line by fitting up the 1993-present Honda XR650L. This is an upright Dakar Rally inspired shield, designed to protect the rider without interfering with off-road riding. For on-road riding the Rally shield protects the rider’s chest from fatiguing air blasts while keeping the head in clean air. Duck behind it in the cold or the rain to keep from experiencing the brunt of the elements. During off-road riding the Rally windshield protects the rider from mud, dust, roots, rocks, or branches without becoming invasive. Whether standing on the pegs or ducking behind it, you will be impressed at the protection it offers. Their Rally shields have been tested in the toughest conditions including an entire SORCS hare scramble season.
*The Rally shield for the XR650L is 12.5 inches tall 12.5 inches wide at the bottom and 8.5 inches wide at the top and is made from military grade 1/8 inch cast acrylic.
The touring windshield from Parabellum has been designed, developed and tested using all the knowledge and experience of the KLR riders in their own shop. Using the stock mounting points as well as the cowling mounts increases the rigidity of the shield.
All new fasteners are included. This new design allows you to move your handlebar to different positions and will not interfere with a stand-up position for off-road use.
This shield is constructed of 3/16" military grade cast acrylic that is 17 inches wide at the bottom tapering to 16 inches at the top.
MotoPressor Tire Gauge comes with two chucks. A straight chuck for "easy to get at" valve stems PLUS a 45° chuck for those "not so easy to get at" valve stems.
We all know what a pain fuel Station gauges are. Most are woefully inaccurate and impossible to get onto a motorcycle valve stem. Enter the MotoPressor Tire Gauge…simply attach the MotoPressor Tire Gauge to your valve stem, attach the fuel station chuck to the inline fitting on the gauge and get an instant and accurate reading in PSI or KPA.
No need to switch between the gauge and air compressor hose! Added a little too much air to your tire? Simply press the air bleed button and adjust to your desired pressure.
NOTE: When swapping out the chuck, use plumbers tape on the hose thread. Wrap the thread, in a clockwise direction with 3 - 5 wraps of plumbers tape. Screw on the new chuck and tighten. Failure to follow these instructions will result in air leak!
MotoPressor Tire Gauge comes with a one year limited product warranty.
Specifications:
Includes front and rear brake pads
Includes front and rear pads
Organic brake pads contain man-made high-performance fibers that are used for their light weight, high strength abrasion resistance and thermal stability. These Aramid fibers have a high strength-to-weight, thermal stability and abrasion resistance to provide advantages over steel fiber-based products. They provide excellent stopping power without noise and rotor galling but still provide fingertip control and strong, predictable brake response.
Double-H sintered metal brake pads feature the HH friction rating, the highest in the industry. These pads provide maximum brake effect and last twice as long as organic pads.
Semi-sintered pads have an all new recipe containing 30% copper by weight with an organic matrix. This design combines the long life of a sintered pad with the great feel and lack of rotor damage common with full-sintered pads. These can be used to replace Kevlar or sintered metal compound pads.
Set includes pads for both front calipers.
High performance EBC brake pads.
This is a complete kit that replaces both front and rear brake pads.
This will give you a complete SET (Front and Rear) of brake pads.
Includes front and rear brake pads.
Sport Carbon pads:
Sintered Pads:
Race Sintered:
Includes front and rear brake pads
EBC brake pad set.
Includes front and rear brake pads
Includes front and rear brake pads.
All the parts you need to freshen up your brake master cylinder. New piston, seals, return spring, boot and snap ring.
Made by Nissin, an OEM supplier in Japan
Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
Made with heat-treated carbon steel for longer wear life and reduced galling. Stock size, simple bolt-on procedure.
The idler gear is one of the few plastic components in the DR650 that can significantly impact engine performance if it fails or breaks.
This gear is crucial for driving the oil pump, which ensures proper oil circulation throughout the engine. In the absence of this component, complete engine failure may occur. While the idler gear is not frequently cited as a common failure point in the DR650 engine, failures have been reported, typically manifesting as either a fractured gear or stripped teeth.
During inspection, it is essential to check for any cracks, chipped areas, or missing teeth on the idler gear. Replacing the gear is a straightforward procedure, and it is advisable to do so while the clutch side case cover is already removed for other maintenance tasks, such as NSU screw replacements or clutch hub bushing replacements.
This component is a Genuine Suzuki part.
These top of the line Adventure pegs from Warp 9 are 5" long and 2.5" wide. They will give your feet the perfect perch whether you are cruising down the highway or standing up hammering down a singletrack trail.
Available in Black. Various superficial scuffs or marks that do not affect performance or fitment. Sold as is.
The new 4.1 gallon fuel tank from Clarke. Carries almost 2 more gallons than the stock tank. Available in Blue, Black, Silver, White or Natural
You want a lighter replacement for your heavy steel stock tank? Don't need the extended range (or bulk) of a big tank? The 3.7 gallon tank from Clarke might be just right. It's almost 5 lbs lighter and holds close to 1/2 gallon more fuel than stock to increase your range by about 20 miles. Fits with your stock petcock, Pingel or Raptor petcock.
We worked with TechSpec to have them make custom tank grip pads that look great on both Acerbis (5.3 and 6.6 gal.) and IMS tanks. These pads not only cover those ugly scuffs, but give great knee grip to the slippery plastic.
These have been tested on two of our shop bikes for over 3 years, they did not bubble or peel off in any way.
Kit includes:
Everything you need to dial in your FCR/DR650 conversion. Enough jetting to cover most modifications or altitudes.
Not for the stock carburetor Fits FCR-MX conversions Only
Geared for the do-it-yourselfer that already has a TM40 or HS40. This kit supplies everything you need to convert it for use on your bike.
Kit includes intake and air boot adapters, throttle cables, choke knob, accelerator pump nozzle, a wide selection of main and pilot jets plus a TM40 tuning manual.
Dual stage foam: 2 different pore sizes create more trapping area for even the smallest dust particles. Flame laminated foam: Both "Stages" are not glued but heat sealed to provide maximum air flow. Light color foam makes it easier to see where the filter oil has covered and where it has not.
Most fuel injected systems are very lean in their stock configuration. This is good for economy and emissions, but not performance. This unit allows you to adjust the Fuel/Air (F/A) ratio without remapping the ECU and getting into complicated software programs. The PowerJet Fuel Controller allows you to adjust the fuel map from -4% to +10% by selecting one of 10 built-in settings (including stock).
The device works by measuring the outside air temperature very close to where the stock sensor is located and then adjusts the signal from the OEM air temperature sensor to the ECU to make use of the Air Temperature Correction factor that is built into the stock ECU. The ECU is told that the intake air is a little cooler than it actually is and it responds by richening the injection map very slightly. How much depends on your setting on the PowerJet. This will result in improved throttle response, especially if you have an aftermarket exhaust of any kind.
PowerJet is easily installed by plugging it in between the stock AIT sensor and the bike's wiring harness under the seat. This can be done very quickly as they are exactly the same plugs. Unplug the stock connection, plug in the PowerJet on each side. The PowerJet fits easily under the seat behind the battery as it is rugged and waterproof. PowerJet comes with a full one year warranty.
All the advantages of a flatslide pumper carburetor at a much friendlier price than a Keihin FCR.
Our complete genuine Mikuni TM40 pumper carburetor kit comes with alloy adapter rings bonded to the carburetor body for a firm reliable fit in the stock air boots. We also include new 3" longer than stock throttle cables, a remote mounted choke knob, complete instructions along with a wide range of main jets and pilot jets for fine tuning or to accommodate bikes with extensive modifications.
This rear master cylinder guard is fabricated from 2mm thick 5052 marine grade alloy, CNC machined from one piece for maximum strength and polished for great looks. Made to cover and protect the master cylinder from all kinds of situations, it is supplied with all necessary hardware.
Adventure bike heaven is off-road headed down a dirt road or a trail. If that is your dream, then as you know, you are going to fall. Sometime, someplace, it will happen, so be prepared! Save your bike before it happens.
SW-Motech makes some of the finest protection equipment available. The set-up for the Twin is available in a standard black powder coating or a semi-polished Stainless-Steel tubing. Both sets will protect the vital components of your motorcycle as well as you from damage incurred during a fall, slide or crash. They will preserve the frame, radiator, bodywork and other critical components from touching down with robust tubular steel. The black kit uses 27/21 mm tubing while the Stainless uses straight 22 mm tubing throughout.
Both configurations have a tight fit for great ground clearance and are designed to work seamlessly with other SW-Motech products like their Skid Plate/Engine Guard and SW-Motech Hawk light mounts. Three secure mounting points per side provide the necessary support that make these so strong. There is no drilling, cutting, welding or any other modifications required for mounting but still allows access to the oil filler, tool box and battery. Kit includes all necessary hardware and instructions and an aluminum cover to replace the OEM plastic cover at the lower mounting point on the left side.
Please Note that these Crash Bars are also compatible with the SW-Motech Skid Plate and the SW-Motech Centerstand.
This durable, steel crafted SW-MOTECH Upper Crash Bars Engine Guard protects the tank, fairing and radiator of your Tenere 700 from damage caused by either debris on the road or a crash.
The tough-built, steel constructed bars can ONLY be mounted with SW-MOTECH Lower crash bars (sold separately).
Each engine guard is powder coated black for a sleek finish which remains durable after prolonged use and protects against corrosion caused by the elements.
Features:
Enjoy maximum protection and durability with an SW-MOTECH skid plate. Fully welded aluminum construction is engineered in Germany to provide proper protection from impacts, abrasions and projectile debris. Multiple ventilation slots on the front, sides and bottom of the skid plate permit maximum air-flow to keep your motor cool. Drilling, cutting, welding or any other permanent modifications are not required.
Features:
What's in the box:
If you already have a Quad Lock Case, you can Twist Lock and Go with any of these secure mounts.
Or Choose the Universal Adaptor to use your current phone case.
The Quad Lock® Handlebar Mount is the ultimate smartphone mount for motorcycles, compatible with all Quad Lock® Cases including the Quad Lock® Universal Adaptor for other Android phone devices.
The Quad Lock® Handlebar Mount gives you the flexibility to mount your phone in a convenient and visible location using a rotating head and includes an extension arm if extra clearance is required. With your phone securely mounted to your motorcycle, you can use navigation apps to guide you to your location with ease and always stay connected.
Standard:
NOTE: Case not included
Motorcycle Vibration Dampener is recommended for use with this product.
This high output stator will allow you to run brighter lights, heated gear, heated grips, etc. From ElectroSport
Heavy Duty replacement Voltage Regulator. More robust, but lower cost than the factory unit.
RallZ is the most aggressive off-road adventure tire in the Motoz range. Its DNA is part desert race tire and part long distance adventure tire. An ADV tire designed in Australia for adventure and rally use. Based on the popular Tractionator Adventure but with more aggressive off-road traction in all weather extremes.
DOT ECER75 approved.
NOTE: Tubes can be run in Tubeless (TL) tires, but a Tube Type (TT) tire cannot be run Tubeless.
Replacement Inner Tubes for your VanVan or TW200. Always a great idea to carry a spare on your adventures as the rear tube is often hard to find.
Having the proper fork oil level is imperative to the handling of your bike. Setting the correct fork oil level is a snap with this fully adjustable gauge. The adjustable aluminum level plate can be set from 0 to 295mm. The oil reservoir has single milliliter markings up to 60ml.
Being able to accurately tune your forks by adjusting the oil level can make them better resist brake dive or bottoming. Oil level should be thought of as a fine tuning method to make your choice of spring rate work perfectly for your bike.
The Optimate Cable O-20 is a SAE weatherproof bulkhead/panel mount power source. Main body fits a 1" dia. hole. Overall length of the unit is 12" from top of bulkhead to end of connector. Both connectors are industry standard 2-pin SAE connectors. We also offer an optional stainless steel bracket that you can bolt on wherever you like. This makes a clean installation and you won't have a charging cable hanging loose.
Cable max. rating is 10 Amps. Includes an in-line rubber seal at the connector end and a protective cover at the bulkhead for when you don't have something plugged in. Unit has a 3-year limited warranty.
Don't have an SAE plug attached to your battery? Choose the add on below.
A set of replacement brake and clutch levers. Standard length.
Replacement shift lever with folding tip.
Say goodbye to the frustration of fidgety handguard expansion plugs with Warp 9's innovative Tapped Handlebars.
These handlebars feature ends that are plugged and tapped with an M8x1.25 threaded insert, providing a secure and reliable mounting point for all aftermarket wrap-around handguards.
No more worrying about plugs pulling out or spinning during crashes; their robust design ensures you're good to go, even when you encounter obstacles.
Not using handguards? No problem they've got you covered!Each set of handlebars comes with aluminum grip guards and stainless bolts, offering protection for your grips and delicate throttle tube in case of a get-off.
Designed with an oversized 1-1/8 inch (28.6mm) clamping diameter that tapers down to 7/8 inch (22.2mm) to accommodate standard controls. Crafted from 7010 T6 aluminum tubing and featuring computer-extruded variable wall thickness, they effectively reduce vibration while enhancing overall performance and comfort.
Note: Does not include pictured bar mounts.
| Width | Height | Rise |
| 790mm | 101mm | 71mm |
| Clamp Area | Sweep | Bend |
| 142mm | 73mm | CR High |
Matte black 118mm x 85mm mirrors. Similar to stock size.
• 8mm thread
Sold In Pairs
For the frame drain on your XR650L ,extra protection for your motor! Strong magnet at the end of the plug picks up metallic flakes in your oil, protecting your engine!
