Quality steel sprockets and 525 O-Ring chain. 525 chains come in 120 link length and will have to be cut down to fit. They also come with rivet type master links. Clip type master links are available below. Single sprockets and chains are also available below.
Available for stock gearing, 49 tooth rear sprocket
OEM Honda rear sprocket for the XR150L
High quality steel rear sprockets from 39 to 53 teeth.
Sprocket color may differ depending on size.
Black hard anodized alloy sprocket. Machined sprockets made from 7075 T651 aluminum reduces distortion and provides optimal thickness, to extend sprocket and chain life.
Rear Sprocket
Note: 2002 and later models have a 10mm sprocket bolts. 2000-2001 models have 8mm sprocket bolts.
JT Sprockets is the world's leading manufacturer of aftermarket sprockets, constantly raising the industry's standards for quality and service. JT Sprockets are the only sprocket manufacturer using the ultra-durable high carbon C49 steel for rear sprockets.
Stock Gearing: 15/45-520x112
Quality Steel Rear Sprocket
Genuine Kawasaki Rear Sprocket. Size 57T
These quality JT sprockets are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.
For reference, the stock gearing for the WR250R is 13/43 while the X model runs with a 13/42 stock configuration because of the SM wheels/tires. Both use a 108 link chain with the stock gearing.
The JT rear sprockets listed are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.
Limited availability on Aluminum from PBI. Manufactured from aircraft 7075 T651 Plate Aluminum.
If you want the additional low-end grunt that the 46, 48 or 50 tooth rear sprocket will give you, you will need longer chain as well.
New Rear Sprockets require new Sprocket Bolts because of a difference in the holes vs. the stock bolts.
Quality steel rear sprockets. Choose 41T through 47T. The stock size for the 650 is 47T.
The stock size for the 02-05 1000 is 42T and 06-up is 41T. Go up in tooth count for faster acceleration. Go down for lower rpm at cruising speed.
Color may vary based on manufacturer availability, quality will not be compromised.
Quality rear steel sprockets.
Quality Steel Rear Sprocket.
Color may vary based on manufacturer availability, quality will not be compromised.
Not for '17 - '20 KLX140G models
These quality JT sprockets are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.
We have 44, 45, 46 and 47 tooth rear sprockets available for the SV. Select the sprocket size from the dropdown.
Steel rear sprocket.
Color may vary based on manufacturer availability, quality will not be compromised.
High quality steel sprockets.
Stock Gearing: 15/48-128x128
Quality steel front sprockets. Choose 525 or 520. Also available 'Wide Boss' JTF438 520 sprockets.
All 520 sprockets require a new retainer plate, please add on if purchasing this size.
High quality sprocket available in the stock size, 14T.
Counter shaft sprocket replacement requires the removal of the left side case cover. A new gasket may be required. This is also a great time to replace that leaking oil seal!
High quality steel front sprockets.
JT Sprockets is the world's leading manufacturer of aftermarket sprockets, constantly raising the industry's standards for quality and service. JT Sprockets are the only sprocket manufacturer using the ultra-durable high carbon C49 steel for rear sprockets.
High quality steel front sprocket
For reference, the stock gearing for the WR250R is 13/43 while the X model runs 13/42 stock gearing.
JT Sprockets is the world's leading manufacturer of aftermarket sprockets, constantly raising the industry's standards for quality and service. JT Sprockets are the only sprocket manufacturer using the ultra-durable high carbon C49 steel for rear sprockets.
13T O.E. type rubber cushioned sprocket.
Quality steel front sprockets. Choose 13T through 15T. The stock size for the XRL is 15T. Go down in tooth count for faster acceleration.
These quality JT sprockets are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.
JT Sprockets is the world's leading manufacturer of aftermarket sprockets, constantly raising the industry's standards for quality and service. Made exclusively from the finest Japanese 545C high carbon steel
Choose either a 14, 15, 16 or 17 tooth JT countershaft sprockets.
Go down in tooth count for faster acceleration.
Go up for lower RPMs at cruising speeds.
Made from the latest generation of computer design and control metal cutting equipment for maximum durability. Made exclusively from the finest Japanese 545C high carbon steel.
All sprockets are heat-treated and hand-finished to meet or exceed the highest possible quality standards.
Quality JT sprockets are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.
Machined from impact and wear resistant chromoly steel. Heat treated, then finished with a nickel coating for corrosion resistance.
Individual 14T, 15T or 16T front sprockets.
JT Sprockets are made from the latest generation of computer design and control metal cutting equipment for maximum durability. Front sprockets are made from chromoly SCM420 steel alloy. All sprockets are heat-treated and hand-finished to meet or exceed the highest possible quality standards.
High quality steel front sprockets from 12T to 14.
Color may vary based on manufacturer availability, quality will not be compromised.
These quality sprockets are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.
JT Sprockets are made from the latest generation of computer design and control metal cutting equipment for maximum durability. Front sprockets are made from chromoly SCM420 steel alloy. All sprockets are heat-treated and hand-finished to meet or exceed the highest possible quality standards.
Currently available in 15 tooth size only, other sizes coming soon.
For all years.
Quality steel sprockets and EK SROZ2 525 O-Ring chain. Available in gear ratio choices from - 13/42 to 15/46. EK SROZ2 525 chains come in 120 link length and may have to be cut down to fit. They also come with rivet type master links. Clip type links are available below.
13 and 14 Tooth sprockets require a smaller retainer
JT steel rear sprockets are manufactured using only the finest grade of C49 high carbon steel.
Two styles of rear sprocket were used on the DR350. The 90-95 'S' and 'SE' (street legal) models have a cush drive hub. The 96-99 'S' and 'SE' as well as all of the 'dirt only' models have a non-cush rear hub. Select your sprocket accordingly. If you are not sure, look at your bike. If the sprocket is bolted directly to the wheel hub you have a non-cush model. If your sprocket is bolted to a separate sprocket carrier you have a cush drive model.
Many riders choose to convert over from the stock 525 to a 520 chain. Besides being lighter and less expensive, a 520 chain is more readily available as well as having more sprocket size options.
High-quality DID chain and steel sprockets for 2002 & later TTR125s.
Developed for Enduro, SX, MX and off-road. Suitable for all types of riding.
Works with all standard and sealed chains.
Includes new mounting hardware.
Industry leading plastic formula “RMS” (Return Memory System).
Absorbs impacts and returns to center.
Friction reducing additives and UV protection to eliminate color fade.
POWERLIP Chain Roller Kit.
Model specific dual roller kit with raised Powerlip.
Includes two rollers. One upper and one lower mounting locations.
The 244 Series Dual Sport street and trail tires were designed to be equally at home on dirt or pavement. Great value.
Kenda's Dual-Sport tire designed for the 10% on-road, 90% off-road crowd.
We offer two different types of SuperMoto tubes. The first are Standard Tubes and are meant to be used with standard bias-ply type tires, but can be used with radial tires also.
But, if you are running radial tires, like SuperMoto, or have a retro bikes with spoked wheels and radial tires, you probably want to run the 'Radial Tubes'. Front tubes fits 120/70 and 120/60 tires. Rear tubes fits 150/60, 150/70 and 160/60 tires. These have a metal valve stem.
This DOT kit includes LED headlight assembly with plug-and-play wiring harness, a specially designed adjustable steel mounting bracket, and all the required installation hardware.
No cutting, no drilling, no wiring modifications! Installation takes 5 minutes.
This kit is highly recommend over the non-DOT kit. The low beam has extra punch and a proper beam pattern cut-off. The high beam throws light far and wide. It’s already a crowd favorite!
Two colors to choose from, Chrome or Black. Light output and beam pattern are the same for either color.
This plug-n-play kit includes sealed LED headlight assembly and adjustable mounting brackets specifically designed for the 1996-2020 DR650SE. No wiring, soldering, resistors, drilling, or fabrication required however due to the size of the headlight minor trimming on the backside of factory plastic headlight fairing is needed in non-visible areas.
Taillight & brake light. Attaches to the top side of enduro style (XR, KDX, etc) rear fenders. Dimensions: 2 3/8" x 4 3/4" x 1 3/4" tall. This light is a popular replacement for the gigantic stock XR650L taillight. Functions as taillight and brake light. Fits perfectly into the taillight pocket on the XR650L. Please note that this no longer has a window for a license plate light.
Will NOT work with factory panniers.
Easily turn your blinkers into additional running lights and brake lights (rear) for added visibility.
White light in the front and red in the rear. Rear red running lights and bright red brake lights. You can omit the running and brake lights if you wish and still have the best blinkers on the market.
Dazzling bright Amber blinker functions.
All in a spring-loaded stock to prevent damage from a tip over, crash or impact with brush, trees etc. They will bend 360 degrees, but are stiff, durable and nearly unbreakable.
Suzuki DR650 Specific plug and play kit using factory connectors, flasher and diode kit included.
Made from heavy duty 1/8" thick stainless steel, these mounting brackets are specifically designed for mounting 2" LED auxiliary lamps to the front of your TW200. They position the lamps (not included) high & tight to the bike for optimal protection and light projection without interfering with the bike controls, body work, or fuel tank. Kit includes four longer mounting bolts for the lower triple clamp.
The image shows a GoPro camera on the TW's right side and an LED light on the left. You could certainly do something like that as well!
The Powercore 4 spark arrestor muffler. FMF developed the Powercore 4 to increase the horsepower and torque throughout the entire power curve. Highest quality packing for long life. Removable spark arrestor included. Louder than the Q4. Approximately 99db stock or about 94db with optional Quiet Insert installed.
Delayed stock from manufacturer, please ask for availability.
Sold Individually
High quality replacement cables from Motion Pro.
This unique design from Rox allows you to move your bars either closer (1" up and back) or further away (1" forward and 1-1/4" up) depending on rider preference. These risers have an oblong mounting hole so that they will fit virtually any triple clamp with 8mm bolts. A set of reducers lock into the risers ensuring no slippage whether you have a 7/8" or 1-1/8" bars.
Because these are offset there may be limited clearance between the gas tank and the risers when the bars are fully turned on some models, mainly when mounted to move the bars closer.
This bar kit will raise your hands 5.5" up from the factory riding position. If you are over 6 feet tall, this is the kit for you! It allows for a more natural riding position, no more bent neck and being hunched over the bars. You will be able to ride comfortably and more aggressively by installing this kit.
The ProTaper bars are taller and tapered from 1 1/8" to 7/8" and the braided stainless steel brake line will be a serious improvement to your braking ability. Braking becomes more responsive and firmer while adding a stylish look to your TW200.
Everything you need is in this kit to properly raise your bars:
The Mikuni TM42-6 HSR flows 17CFM more than the TM40-6 and incorporates many upgraded features such as a roller-bearing slide.
All this means going even faster has never been so easy, say goodbye to hard starting, hesitations and flat spots.
This seal helps keep debris and water out of your DR650 air box and it may become damaged or missing over the years. It is an important part of your DR650's intake system to maintain & prolong air filter life.
Simply, remove the air box door, then remove the old seal and clean out the track it sat in. Set the new seal in place and cut off any excess material remaining. Install the air box door and you are done.
Is the cylinder head intake boot on your DR650 cracked or weathered, is it missing parts of the lip to seal around the carburetor, have you recently pulled the intake boot off only to realize the O-ring behind it is hard & brittle? This kit is your solution to solving some of those mystery problems and make your bike like new again. There can be a great deal of heat that can radiate behind the cylinder head on a DR650 as it is an air cooled engine. With that comes long term maintenance items that will need to be replaced due to them being made of materials that cannot withstand those constant heat cycles indefinitely.
Our kit includes O.E. parts from Suzuki to include:
The jet kit for riders who want their bike to run well but do not want to modify the air box.
The Ti ProKit w/Titanium needle adds more power and better throttle response. Easy to install and tune - no slide drilling. No air box modification.
Includes: a main jet selection, adjustable titanium needle, clips (with extras), pilot jet, instructions.
The 790cc Big Bore Kit includes a custom made, forged 9.5:1 piston with rings, wrist pin and circlips. A custom made multi-layer steel head gasket, OEM metal base gasket, tensioner gasket, and cam bolt lock plate and a ProCycle specific big bore cylinder sleeve.
Built cylinders with 790 sleeves installed are usually in stock, but we must have your original cylinder sent to us as a 'core'. These cores allow us to keep up this program and it is nothing more than an exchange - we give you ours, you give us yours.
This Kit Includes:
Rebuilding your engine? Here is a complete gasket kit for your TW200.
Includes:
Top end gasket set with the addition of a factory Suzuki metal base gasket. A metal base gasket is essential because paper base gaskets will fail in the DR650.
Complete set of engine gaskets and oil seals. Includes the addition of a factory Suzuki metal base gasket. A metal base gasket is essential because paper base gaskets will fail in the DR650.
Kit Includes:
The EBC DRC kit is the best way to reset your bike’s clutch to the exact as new standard sizing. Replacing just the plates can work but new clutch springs are always better and springs get tired and can cause slippage plus the separator steel plates from EBC are pin-planished, forming tiny indents in the steel which improves the spread of oil around the clutch surfaces.
Includes:
Warp 9 Stainless Steel Reusable Oil Filter
This is one of the toughest skid plates we've got. Manufactured from 3/16" aluminum that is laser cut and CNC formed, all joints are welded on both sides. The rear mounting bolts are fully recessed for protection. A welded block protects the bolt heads from being bashed and rounded from obstructions. Rubber isolators between the plate and the frame at these two bolt locations help to eliminate vibrations and keep noise down. Front mounts clamp around the frame for a solid connection.
The right side of the plate extends up to cover the oil filter and unbolts from the skid plate for easy filter changes. This skid plate has a black textured powder coat finish for great looks and durability. Includes stainless steel hardware.
The Rally Pro X-Strong features a high-impact, composite injection-molded outer guard surrounding an anodized aluminum inner guard. It is equipped with an indexed steel bar-end insert that ensures a secure installation, preventing Rally Pro handguards from slipping, even in challenging conditions. Additionally, a compact integral spoiler is incorporated into the design. The package includes a robust universal silver mount kit that is compatible with 7/8” (22mm), Pro Taper 1 1/8” (28mm), Magura, and Twin Wall aluminum handlebars.
Some models with adjustable windscreens may need the windscreen rotated forward, such as the Royal Enfield Himalayan, to avoid contact at full lock. These are not compatible on Honda CB500X's and Honda Africa Twins.
Have you already ditched the bulky tail light on your XR? Don't want to bend your license plate and wrap it around your rear fender? Here is a great solution to clean up the looks of the backside of your XR650L. If you haven't already upgraded to the smaller and better looking WPS Tail light, select 'Bracket & Light' from the menu and you will get the WPS Taillight AND the License Plate Holder.
Please note that this no longer has a window for a license plate light. To stay legal, you can mount one or two License Plate Lights to your plate holder, or you can check out the LED License Plate Frame.
Replace those worn out brake pads with quality EBC replacements.
These DP Standard brake pads are our OEM replacement sintered metal compound. Ideal for everyday use, both on and off-road. They provide excellent all-round braking hot or cold, wet or dry. Where applicable a high-tech ceramic heat shield is applied to the rear of each backplate to reduce the heat transfer into the fluid and prevent brake fade. They have one of the lowest wear rates on the market, very low levels of brake dust and no noise and no thermal cycle bedding-in required are also benefits of the DP Standard brake pads.
Quality components at a great price.
High quality carbon steel brake rotor.
A great option for every day use, or on your spare rear wheel.
Each kit includes all necessary rubber components and brake pins.
GBrakes Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
All that you need to repair and inflate your tire on the road or trail.
Kit includes:
CO² cartridges cannot be transported on an aircraft.
DRZ400 rack is available in both a Utility and Sport version. The Sport version is 9" x 9" and the Utility is a full 2" longer for added storage space. Both of the S/SM racks have tabs so you can bolt the stock tool bag on.
Please select the rack for your specific model as the differences are significant
These flat tie down 'stretch' straps are designed specifically for motorcycles, ATVs and snowmobiles. Carry anything on your motorcycle securely and without scratches with these flat - no hook - tie down straps.
ROK Straps are a two-piece strap with a quick-release buckle in the middle and loops on each end. One end of the strap is a heavy duty nylon, the other has a strong stretchable section. Instead of hooks that can slip or come undone, ROK Straps have a loop sewn in each end. you pass the buckle around your frame, rack or other secure point and then back through the loop in the end making for a very secure mount. With each end secured, connect the buckle in the middle and simply tug the slack end of the strap until your load is firmly held in place.
The Motorcycle Adjustable Strap is 1 inch wide and adjusts in length from 18 to 60 inches.
Rated to carry 100 lb (200 lb burst strength)
Designed specifically for motorcycle and ATV use.
Warp 9 Dual Sport wheels are built with billet hubs, 7000 series aluminum rims and laced and trued with stainless steel spokes and nipples. NAK seals, OEM bearings, Zinc plated nyloc hardware.
The 1.85" x 21" front wheel includes a wave brake rotor.
The 2.50" x 18" rear wheel is built using an upgraded cush drive hub that features polyurethane dampers and includes a rear brake rotor already mounted.
Rear wheel includes a Sprocket Carrier with 7075 T6 aluminum 45T sprocket installed that matches selected hub color.
Add tires to your wheel order and we will throw in tubes and mount and balance them at no additional charge.
The EJK evolved out of the need to address the ever-increasing complexity of factory fuel injection. For the newcomer to the market or professionals wanting an easier method for tuning fuel injection, the EJK is a customizable solution for the rider that wants to take control of their tuning needs.
This unit is a piggy-back EFI controller because it does not replace the stock ECU, but rather monitors the signals to the injectors and makes fuel adjustments based on the mode settings. The GEN 3 has a push button interface allowing access up to 6 different modes to allow for quick fine tuning by the end user without needing a computer.
Key Features:
This clever carbon fiber wrap can either hide your ugly off road sticker or give you a place to attach your sticker so that you don't leave that sticky glue on your fork leg.
Easy snap on fit for most larger displacement motorcycles. Fits on the upper section of upside down forks or on the lower section of conventional forks.
Does not fit smaller forks like those on the TW200 or XT250.
Upgrade your Honda XR650L with a Subframe Brace Kit, designed to enhance strength and rigidity for your bike. This complete kit connects the frame and subframe, reinforcing the structure to support increased load capacity—perfect for riders using side cases, top cases, and rear racks.
Key Features:
High-Quality Materials: Attachment points are machined from 6061-T6 billet aluminum for superior strength and durability.. The 6.5mm thick support bars are laser-cut for a perfect fit.
Easy Installation: No cutting, drilling, welding, or modifications required for installation. Easy 20 min installation.
Enhanced Load Capacity: Provides added rigidity and support to the subframe, improving bike stability when carrying additional gear.
Exhaust Compatibility: Compatible with both STOCK Exhaust and FMF Exhaust systems.
These Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. These units have been given the seal of approval by the ProCycle staff for both performance and ease of installation. No disassembly of your forks, no drilling of damper rods. Just change the oil over to 5w and install the DDCs under the springs and hit the trails.
Stiffer fork springs are recommended to get the full potential of the DDCs.
Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. Designed by Rick at Cogent Dynamics on his high-tech suspension dyno, then tested and endorsed by KLR owners all over, these units have been given the seal of approval by the ProCycle staff for both performance and ease of installation. No disassembly of your forks, no drilling of damper rods. Just change the oil over to 5w and install the units under the springs and hit the trails.
If you weigh up to 250 pounds, select the .64 spring kit. If you are over 250 or carry lots of luggage, please select the .70 spring kit. Please call if you have any further questions.
All of these kits include DDCs, springs, fork oil and preload spacers.
Developed by the KLR suspenison experts at Cogent, this set of springs will stiffen up that wimpy KLR front end. Choose between .64 kg/mm springs (60% stiffer than stock) or .70 kg/mm units (75% stiffer than stock).
Will not work for 2014-Cur 'Mid-Year' New Edition Model
With a Haynes manual, you can do it yourself…from simple maintenance to basic repairs. Haynes writes every book based on a complete teardown of the motorcycle. Haynes books have clear instructions and plenty of photographs that show each step.
Complete coverage for your Yamaha Trail Bikes covering PW, RT, TT-R and XT225/350 models for 1981 thru 2000.
This boot goes way beyond our expectations in comfort, protection, quality and affordability!
Only Available in Brown - 8 US/ 42 EU/ 11 Wmns
50mm step width provides better grip and control
