These Cogent Dynamic Drop-in Cartridges will vastly improve both the compression and rebound damping of your stock forks. These units have been given the seal of approval by the ProCycle staff for both performance and ease of installation. No disassembly of your forks, no drilling of damper rods. Just change the oil over to 5w and install the DDCs under the springs and hit the trails.
These Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. These units have been given the seal of approval by the ProCycle staff for both performance and ease of installation. No disassembly of your forks, no drilling of damper rods. Just change the oil over to 5w and install the DDCs under the springs and hit the trails.
Stiffer fork springs are recommended to get the full potential of the DDCs.
Included in this kit are fork springs, Cogent DDC (Drop in Damper Cartridge) performance cartridges and three bottles of 5w fork oil. Refresh those tired old forks and make them better than new. These DDCs from Cogent are easy to install. No taking the forks apart, no drilling of the damping rods, nothing. Just take them off, flip them over to drain the oil, add new 5w oil, drop in the DDCs and then add the springs and spacers and then install the caps. Preload spacer material is included with the .47 and .70 springs, additional spacers are not needed with the other kits.
This upgrade offers better control off-road as well as on. Less brake dive keeps the fork up in the middle of the stroke on-road and better control off-road whether it be rolling water bars or bouncing off the rocks.
Rider and Gear up to 160lb. = 0.47 springs → 24% stiffer than stock
Rider and Gear 160-225 lb. = 0.52 springs → 39% stiffer than stock
Rider and Gear 225-275 lb. = 0.58 springs → 56% stiffer than stock
Rider and Gear 275-325 lb. = 0.63 springs → 66% stiffer than stock
Rider and Gear 325 lb.-UP = 0.70 springs → 84% stiffer than stock
Progressive springs offer a soft initial spring rate for a plush ride. Progressively wound design provides increased resistance to bottoming as spring compresses. These springs are significantly stiffer than the wimpy stock springs.
They will make a big improvement in front fork action while still delivering a smooth ride. Sold in pairs.
Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
Significantly improves response and feel over factory rubber lines
Largest performance improvement for your money over any other braking upgrade
Stainless steel hose resists abrasion and puncture
Teflon core does not degrade over time like rubber lines
PTFE Dupont 64 Teflon® hose
Feature a heavy-duty stiffener sleeve and route just like the factory lines
Proprietary, premium fittings
Banjos utilizes a unique machined channel and sealing surface for leak-free installations
R&D and engineered in the USA
GBrakes USA controls the manufacturing process, ensuring the highest level of quality control
Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
Significantly improves response and feel over factory rubber lines
Largest performance improvement for your money over any other braking upgrade
Stainless steel hose resists abrasion and puncture
Teflon core does not degrade over time like rubber lines
PTFE Dupont 64 Teflon® hose
Feature a heavy-duty stiffener sleeve and route just like the factory lines
Proprietary, premium fittings
Banjos utilizes a unique machined channel and sealing surface for leak-free installations
R&D and engineered in the USA
GBrakes USA controls the manufacturing process, ensuring the highest level of quality control
The Rally windscreen from Parabellum is the perfect protection from wind and debris without sacrificing technical off-road capabilities. This is an upright rally type windscreen that looks aggressive and performs well under all types of riding. Designed primarily for the off-road / dualsport enthusiast, this shield keeps pressure off the rider's chest while commuting from home to adventure and back.
Mounting is accomplished by drilling two holes on each side of your headlight cowl using the provided template. 13.5 inches tall, 11.5 inches wide at the bottom, and 8.5 inches wide at the top. Made from military aircraft grade cast acrylic.
Parabellum LTD. has continued the highly demanded Rally Shield line by fitting up the 1993-present Honda XR650L. This is an upright Dakar Rally inspired shield, designed to protect the rider without interfering with off-road riding. For on-road riding the Rally shield protects the rider’s chest from fatiguing air blasts while keeping the head in clean air. Duck behind it in the cold or the rain to keep from experiencing the brunt of the elements. During off-road riding the Rally windshield protects the rider from mud, dust, roots, rocks, or branches without becoming invasive. Whether standing on the pegs or ducking behind it, you will be impressed at the protection it offers. Their Rally shields have been tested in the toughest conditions including an entire SORCS hare scramble season.
*The Rally shield for the XR650L is 12.5 inches tall 12.5 inches wide at the bottom and 8.5 inches wide at the top and is made from military grade 1/8 inch cast acrylic.
The unique design of the electrode maximizes the power generated by the spark plug through Diamond Fire technology. This electrode combines advanced performance capabilities and innovative technology to enhance the shape of the flame kernel. Consequently, the flame front ignites the air/fuel mixture more rapidly, accelerates heat transfer into the combustion chamber, and creates a more concentrated pressure front, facilitating a quicker pressure rise during the cylinder power stroke. The outcome is a more efficient combustion process and improved engine performance, making this a truly premium spark plug.
The idler gear is one of the few plastic components in the DR650 that can significantly impact engine performance if it fails or breaks.
This gear is crucial for driving the oil pump, which ensures proper oil circulation throughout the engine. In the absence of this component, complete engine failure may occur. While the idler gear is not frequently cited as a common failure point in the DR650 engine, failures have been reported, typically manifesting as either a fractured gear or stripped teeth.
During inspection, it is essential to check for any cracks, chipped areas, or missing teeth on the idler gear. Replacing the gear is a straightforward procedure, and it is advisable to do so while the clutch side case cover is already removed for other maintenance tasks, such as NSU screw replacements or clutch hub bushing replacements.
These quality JT sprockets are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.
Quality JT sprockets are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.
Backordered: Waiting for stock from suppliers to fulfill orders placed on or after June 2025
For reference, the stock gearing for the WR250R is 13/43 while the X model runs with a 13/42 stock configuration because of the SM wheels/tires. Both use a 108 link chain with the stock gearing.
The JT rear sprockets listed are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.
Limited availability on Aluminum from PBI. Manufactured from aircraft 7075 T651 Plate Aluminum.
If you want the additional low-end grunt that the 46, 48 or 50 tooth rear sprocket will give you, you will need longer chain as well.
New Rear Sprockets require new Sprocket Bolts because of a difference in the holes vs. the stock bolts.
These quality JT sprockets are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.
Quality steel sprockets and 525 O-Ring chain. 525 chains come in 120 link length and will have to be cut down to fit. They also come with rivet type master links. Clip type master links are available below. Single sprockets and chains are also available below.
Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a more plush and active ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.
On this model, they built up the front of the seat, but dished out the rear slightly to level out the angle of the rider platform, and reduce the slope-into-tank feeling of the stock seat.
These features combine to offer a custom seat feel, and provide greater enjoyment and increased range on a long commute, or Dual-Sport ride!
Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!
Available as a Foam and Cover Kit for OEM pan. It DOES NOT include the pan.
Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a plusher ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.
These great features combine to offer you a custom seat feel, and provide greater enjoyment and increased range for long commutes, or Dual-Sport rides!
The Complete Seats come assembled with an aftermarket pan and ready to ride.
The Commuter shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but is much more dished out towards the mid-point to distribute rider weight over a greater area. The passenger platform has been built up to help prevent the passenger from sliding into the rider.
The Commuter seat is the best choice for extended pavement riding and mellow offroad. The unique shape and added width will provide greater enjoyment and increased range on a long commute, or Dual-Sport ride!
The ProCycle seat was designed for both comfort and function. Our seat is built with a premium grade foam that is denser for those long days in the saddle, and also giving you freedom to move while standing.
The wide and sturdy seat makes long rides more comfortable. The vinyl weave helps keep you cool by letting air flow between you and the seat. The front of the seat is narrower, giving you space for your knees when you're standing, while the sides have grip so you can hold on with your knees while riding. If you choose the gel cushion option, it helps improve blood flow, prevents pressure points, and makes it easier to ride for longer without getting tired.
We will build the seat for you in-house on a new seat pan so all you have to do is put it on and go ride. Choose the heated seat option and we will add a Seat Warmer during the build process.
Have you lost or broken the stock air filter cage for your KLR? Maybe you need a spare? Here it is, the OEM cage that will fit any of the foam air filters on this page. This kit includes the cage and the mounting hardware.
This Kit replaces vital components in the BST40 Carburetor including new a Float, Needle Valve, Gaskets, Seals, Diaphragm, Spring and Float Bowl Screws to return the stock Mikuni BST40 Carburetor to like-new operation. As a bonus we have included Viton o-rings for the float assembly and 4 stainless steel allen screws.
Universal fit. May require additional adjustment or modification.
For Straight 7/8" handlebar
Contoured alloy hand guards with inner mounts, allow space for the clutch cable and brake hose.
Note: This kit includes the handguards only. Deflectors sold separate, can be added by selecting color from drop down menu.
For DR650 or other models with long levers add the optional universal fit Spacer Kit so you don't have to cut the balls off the end of your levers when installing these handguards. (May require additional adjustment or modification on some models.)
Universal fit. May require additional adjustment or modification.
The X-Factory Handguards from Acerbis are designed with a steel bar encased in an injection-molded Nylon composite. A replaceable dual-injected polypropylene shield attaches to the bar, providing excellent protection against debris and harsh conditions.
Included with the handguards is a universal mount kit, enabling installation on either 7/8" or 1 1/8" handlebars.
Will not fit XT250 with stock handlebars (oversize bars ok). Recommend Acerbis Rally Pro X-Strong to clear master cylinder.
This rear master cylinder guard is fabricated from 2mm thick 5052 marine grade alloy, CNC machined from one piece for maximum strength and polished for great looks. Made to cover and protect the master cylinder from all kinds of situations, it is supplied with all necessary hardware.
Universal fit. May require additional adjustment or modification.
RotoPax holder made to mount a single Fuel and/or Water container.
Need to mount two containers? A water and a fuel? Two waters? Get the extender which allows you to stack two containers no problem! Single mount, two containers
Universal fit. May require additional adjustment or modification.
Say goodbye to the frustration of fidgety handguard expansion plugs with Warp 9's innovative Tapped Handlebars.
These handlebars feature ends that are plugged and tapped with an M8x1.25 threaded insert, providing a secure and reliable mounting point for all aftermarket wrap-around handguards.
No more worrying about plugs pulling out or spinning during crashes; their robust design ensures you're good to go, even when you encounter obstacles.
Not using handguards? No problem they've got you covered!Each set of handlebars comes with aluminum grip guards and stainless bolts, offering protection for your grips and delicate throttle tube in case of a get-off.
Designed with an oversized 1-1/8 inch (28.6mm) clamping diameter that tapers down to 7/8 inch (22.2mm) to accommodate standard controls. Crafted from 7010 T6 aluminum tubing and featuring computer-extruded variable wall thickness, they effectively reduce vibration while enhancing overall performance and comfort.
Universal fit. May require additional adjustment or modification.
These heated grips from Koso have been tested by us and we can say they will keep your hands warm and give you the grip you need in off road conditions, thanks to the full diamond grip design.
Clamp-on grips do not need adhesive
External temperature controller with 5 heat levels
For use with twist throttle; includes interchangeable throttle cams
Requires 35W and draws 2.5 amps per pair; low voltage shut off
Designed to enhance the appearance of your TW200, yet provide greater riding distance per tankful. This larger fuel tank has double the capacity of the stock tank at 3.6 Gallons, yet very slim and sleek. This tank has a custom design that will allow the use of OEM & Maier side covers. These tanks are made with POLYETHYLENE CROSSLINK for extra strength and durability.
Comes with New Screw Cap.
Requires OEM/Stock petcock and oval rubber grommets for install.
If you do not have the grommets or if your O.E. grommets are in poor condition you can add these to your tank order.
Universal fit. May require additional adjustment or modification.
Filling and bleeding a Magura hydraulic clutch does not need to be a routine chore and should only need to be done when air infiltration within the system is suspected. Magura uses mineral oil, which does not absorb moisture from the environment, to lubricate the whole system.
Note: Magura hydraulic systems use ONLY mineral oil. Do not introduce DOT brake fluid of any kind into a hydraulic system designed to use mineral oil as this will cause corrosion to the internal seals and system failure may result. The only time anyone should ever need to replace the hydraulic fluid in a Magura system is following a hydraulic line exchange, a system upgrade, a crash which has damaged the system components or in a situation where a lack of fluid within the system has been diagnosed by poor lever feel.
If you do need to bleed your Magura hydraulic system, their custom made kit does indeed make that chore easier.
Universal fit. May require additional adjustment or modification.
RallZ is the most aggressive off-road adventure tire in the Motoz range. Its DNA is part desert race tire and part long distance adventure tire. An ADV tire designed in Australia for adventure and rally use. Based on the popular Tractionator Adventure but with more aggressive off-road traction in all weather extremes.
DOT ECER75 approved.
NOTE: Tubes can be run in Tubeless (TL) tires, but a Tube Type (TT) tire cannot be run Tubeless.
Universal fit. May require additional adjustment or modification.
An ADV tire designed in Australia for real off-road riding. Technically 25% stronger than many adventure tires with a tread deeper than most and a compound formulated to perform in a wide variety of conditions. The tread design on this tire is unique in that the blocks self-sharpen for better grip through the life of the tire.
If you want the best in traction, wear and dependability, try a set of Tractionator ADV Rear with Dual Venture Front. All sets now have Dual Venture Front with ADV Rear.
NOTE: All of the sizes listed are Tubeless Tires (unless otherwise noted) and can be used as such with tubeless certified wheels. Tubes can be run in Tubeless tires, but a Tube Type tire cannot be run Tubeless.
Universal fit. May require additional adjustment or modification.
The GP-1 Dual Sport Tire from IRC is designed to provide the best possible handling and control for both on and off the pavement. Special knobs penetrate loose surfaces for excellent traction, braking and cornering off the road yet won't wear off as fast as a full knobby when used on the street. Features include:
The DG RST (Reduced Sound Technology) muffler is the quietest DG muffler and is designed especially for dual-sport machines (Just 89db @ 3200 RPM). A new baffle design dissipates sound waves reducing noise output in a very efficient manner. This new design also stretches out the time between muffler repacks. Included is a Stainless Steel mid-pipe, USFS Approved Spark Arrestor and a new Aluminum end cap.
You may want to consider a new exhaust gasket that goes between the header and the muffler.
No repacking required! The Leo Vince X3 Enduro is made with TIG welded stainless steel internals and aluminum outer shell. It features a semi-direct chamber design that is maintenance free. It's quiet too! Our own in-house testing showed a 84dB sound level using the USFS J1287 testing procedure. 84dB is louder than stock but significantly quieter than any other aftermarket muffler. It includes a certified Spark-Arrestor.
The PowerBomb header promotes better flow by allowing a small expansion of the exhaust gasses. The 'bomb' also acts as a pre-muffler taking the edge off of overall sound levels. Includes clamp-on mounts for the stock heat shield. We recommend Anti-Seize on exhaust fasteners.
Rear wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.
Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.
Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.
Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.
Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.
The rubber coated outside diameter creates an optimum seal at the hub.
Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.
Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.
Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.
Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.
Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.
Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.
The rubber coated outside diameter creates an optimum seal at the hub.
Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.
Pivot Pegz have set a new standard in foot peg performance and quality and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty.
Pivot Pegz aim is to build the best foot pegs in the world and they really do perform as good as they look. There's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever.
Pivot Pegz have set a new standard in footpeg performance and quality and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty.
Pivot Pegz aim is to build the best footpegs in the world and they really do perform as good as they look. Here's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever.
Mega wide 60mm platform x 100mm long, overall approx length from center of footpeg pin to end of peg is 115mm
The IMS Super Stock pegs are the perfect choice for both the daily commuter and the rider-in-training. Their mellow tooth design keeps you planted while preventing wear on your soles. They are also perfect for young riders who don't need or want a more aggressive option.
If you are replacing your side stand you will want to check the hardware. Over the years they can take a beating and the springs become lost or broken.
This is the full kit that includes #4, #5, #2, and #3 in the diagram.
Universal fit. May require additional adjustment or modification.
Here is a tool to help you remove a few links from a chain that is too long. A great tool to have in your tool box.
The head of the pivot pin you are going to remove must be ground down level with the side plate before using this tool to push it out. Failure to do that will cause damage to the tool that is not covered by any warranty!
Universal fit. May require additional adjustment or modification.
Giant Loop has removed the zipper in the Coyote Saddle bags, and now it is a true roll-top bag. This bag straps on to dirt bikes and dual sport motorcycles, no passenger pegs or racks required. Saddlebag rides on rear fender and/or tail rack.
Includes 3 Dry Pods equipped with air release valves
Universal fit. May require additional adjustment or modification.
The current ProCycle logo on front, with the design on the back showing our favorite 'Pavement Ends' sign with the DR rider continuing up the road on the pegs, ready for an adventure!
High quality soft blend t-shirt perfect for everyday wear (90/10 Airlume combed and ring spun cotton/poly).
Acerbis 3.9 gal tank adds function and great looks to your DRZ. This high capacity fuel tank incorporates modern lines and high quality construction that can't be beat. Includes gas cap, petcock and all mounting hardware.
From Warp 9, top of the line Adventure Pegs. a full 5" long and 2.5" wide will give your feet the perfect perch whether you are cruising down the highway or standing up hammering down a single track trail.
Ceracote coated Chromoly steel pivot for the ultimate in strength
Replaceable 7075 T6 Aluminum Platform
Permanent Stainless Teeth provide the ultimate in non-slip traction
SuperBrace is the leading motorcycle fork stabilizer. This patented brace provides better stability, superior aerodynamics and a more streamlined look than other multi-piece braces on the market.
Reduces low and high speed wobbles
Improves stability in tight cornering
Improves tire life and reduces cupping
Decreases sensitivity to rough road surfaces and rain grooves
Each SuperBrace is designed and manufactured for each specific motorcycle and made of 6061-T6 aircraft aluminum
Antigravity Batteries introduce the ground-breaking "RE-START (RS)" line of batteries. These are the first batteries with built-in jump starting! They intelligently monitor their status, and just before going completely dead, puts itself to sleep with just enough energy to get your vehicle started again. Simply press the RE-START button located on the battery, then start your bike and ride away!
These are an extremely lightweight (2.3 lbs.) and high-powered Lithium-Ion replacement battery for motorcycles. These batteries offer the first Battery Management System (BMS) found on a powersport battery and includes low-voltage cut-off, over discharge, over-charge, and thermal protections with real time lithium-ion cell balancing. Highly recommend using a lithium charger to maintain the life of the battery.
3 Year warranty
Product Size is just 5.9"L x 3.5"W x 3.74"H. If you need spacers, select the optional Foam Kit to pad the battery in the battery box.
Antigravity Batteries introduce the ground-breaking "RE-START (RS)" line of batteries. These are the first batteries with built-in jump starting! They intelligently monitor their status, and just before going completely dead, puts itself to sleep with just enough energy to get your vehicle started again. Simply press the RE-START button located on the battery, then start your bike and ride away!
These are an extremely lightweight (2.3 lbs.) and high-powered Lithium-Ion replacement battery for motorcycles. These batteries offer the first Battery Management System (BMS) found on a powersport battery and includes low-voltage cut-off, over discharge, over-charge, and thermal protections with real time lithium-ion cell balancing. Highly recommend using a lithium charger to maintain the life of the battery.
3 Year warranty
Product Size is just 5.9"L x 3.5"W x 3.74"H. If you need spacers, select the optional Foam Kit to pad the battery in the battery box.
Universal fit. May require additional adjustment or modification.
A professional level adjustable spoke torque wrench. Range from 0 to 62 inch pounds. The handle has a rubber coated end to protect your rims from scratches. Includes Torque wrench, standard handle (for tough disassembly work) and seven different size tips, all packed in a protective case.
Includes Tips 5.1, 5.6, 5.8, 6.1, 6.3, 6.5, 6.7, 6.8, 6.9 and Spline drive.
A 'wrench style' tool to turn the 'square top' tappet screws. The wrench does a better job of holding the adjuster screw still while tightening the locknut. Slim and flat, this tool is easy to carry in a tool pack.
This kit is not just a bulb, but an entirely new LED specific headlight! A specially designed adjustable steel mounting bracket replaces the stock unit. Included is a wiring harness and all the required hardware to make this installation quick and easy and entirely plug and play. No cutting, no drilling, no wiring modifications are necessary. The headlight features separate low and high beam projectors in a custom headlight shell designed specifically for this LED bulb.
Now available with a black chrome reflector!
Check out the images below for stock vs. LED patterns and brightness images.
This device will pulse your brake light automatically. There are over 1000 possible pattern combinations with individually programmable Flash Speeds, Pre-Delay, and Flash Durations, as well as a disable feature to disable the unit. This device gives the end user the widest range of possibilities for customizing your tail light safety flash. With simple programming setup using only your brake lever, their is no disassembly or removing of the seat required to change the programming on the device.
Features:
Independently programmable flash speed, flash duration, and pre-delay
This heavy duty aluminum bracket is specifically designed for mounting auxiliary LED lights to the front of your XR650L without interfering with your large aftermarket fuel tank. If your bike needs improved lighting this mount is the best place to start!
– 0.190″ 5052 Aluminum – Laser cut – CNC formed – Powder coated black – Includes stainless mounting hardware and JNS stickers.
Revolutionize your riding experience with Swiftkicker. An adjustable kickstand for your motorcycle. Swiftkicker is built for offroad motorcycles, dual sports, and dirt bikes. Designed with the idea in mind that motorcycles should be able to take you anywhere, the Swiftkicker motorcycle kickstands help you do just that. You can set the length to anywhere in a six inch range of travel so you can stop anywhere without having to worry about having an even surface to park.
With just a flick of your toe, you can adjust the kickstand to the desired height, park your motorcycle, and be on your way. No longer will you have to search for a rock or piece of wood to prop your motorcycle up with, or even worse, coming back to your bike to find it has tipped over from unstable ground.
The Swiftkicker is 100% manufactured in the USA from the highest quality components. The billet 6061 head and the hard anodized tube are significantly stronger than the stock stand. An oversized foot will assure that the end of your stand stays where it belongs, rather than eight inches underground with your bike lying on top of it. The design is trail proven in the harshest possible conditions. Because nothing is indestructible, any of the kickstand components are replaceable at a lower cost than purchasing an OEM kickstand.
Measured from the center of the pivot to the bottom of the foot.
Standard length travel range is 13.5"-19.5" (the middle of the travel is approximately the same length as the stock stand)
Africa Twin (CRF1100L) Adventure Sport ES '22 - '22Africa Twin (CRF1100L) '22 - '22
Small scuffs on the inside of the bash plate as shown in image, does not affect performance or fitment. Polished finish only, sold as is, all hardware included. Does not qualify for free shipping.
The Honda CRF1100 DCT Bash plate is a full coverage Rally style protection for frame rails & lower to mid engine cases. Constructed for more serious off road use in mind, it features multiple additional mount points, paired with a semi double skin 4mm 5083 aluminum Bash plate. All CNC machined and fully tig welded, the side wings are partial double walled for extra stiffness. It also features the addition of a HDPE end plate for the clutch case mated to a rubber puck insert on the plate for additional protection.
