Search Products

Designed to enhance the appearance of your TW200, yet provide greater riding distance per tankful. This larger fuel tank has double the capacity of the stock tank at 3.6 Gallons, yet very slim and sleek. This tank has a custom design that will allow the use of OEM & Maier side covers. These tanks are made with POLYETHYLENE CROSSLINK for extra strength and durability.

Comes with New Screw Cap.

Requires OEM/Stock petcock and oval rubber grommets for install.

If you do not have the grommets or if your O.E. grommets are in poor condition you can add these to your tank order.

Twin Air Filter's patented design, high quality materials and superior construction deliver unbeatable performance and protection - and make Twin Air Filters the hands-down choice of more World and National Champions than all other filters combined.
An air filter is your engine's only protection against the elements, and your stock filter isn't up to the task. Replace it with a Twin Air- the number 1 filter system proven on motocross tracks around the world.
Twin Air's fused layers of open-pore foam and fine inner foam trap even the smallest particles-without restricting airflow

Dual stage foam: 2 different pore sizes create more trapping area for even the smallest dust particles. Flame laminated foam: Both "Stages" are not glued but heat sealed to provide maximum air flow. Light color foam makes it easier to see where the filter oil has covered and where it has not.

• Made of flame-laminated dual-layer foam, bonded with the highest quality glue to stand up to the roughest and toughest of any style of riding or terrain
• This filter, used with No Toil foam filter treatment, provides the best air filtration system in the world
• Fully open-cell structure for highest airflow and maximum protection
• Heavy-duty glue provides protection from all solvents
• Wide soft sealing ring for extra protection
• Flexible seams prevent cracking
• Original OEM size

• Dual-bonded foam design filters out even the smallest dirt particles, while allowing more airflow than two separate layer filters (flow bench proven)
• Twin Air filters are slightly smaller than stock to make them easier to change and to increase dead air space around the filter for better performance
• Flat foam sealing ring securely seats against the airbox, even in the worst riding conditions

• Manufactured from world-class materials to achieve optimum performance and engine protection
• Precision engineered to perfectly fit the factory airbox
• Direct replacement of original equipment filter

• Precision engineered to perfectly fit the factory airbox, these filters meet or exceed OEM specifications
• Direct replacement of original equipment filter with no need to change carburetor jets or settings
• Manufactured from world-class materials to achieve optimum performance and engine protection

• Precision engineered to perfectly fit the factory airbox, these filters meet or exceed OEM specifications
• Direct replacement of original equipment filter with no need to change carburetor jets or settings
• Manufactured from world-class materials to achieve optimum performance and engine protection

Have you lost or broken the stock air filter cage for your KLR? Maybe you need a spare? Here it is, the OEM cage that will fit any of the foam air filters on this page. This kit includes the cage and the mounting hardware.

• Dual-bonded foam design filters out even the smallest dirt particles, while allowing more airflow than two separate layer filters (flow bench proven)
• Twin Air filters are slightly smaller than stock to make them easier to change and to increase dead air space around the filter for better performance
• Flat foam sealing ring securely seats against the airbox, even in the worst riding conditions

Is the cylinder head intake boot on your DR650 cracked or weathered, is it missing parts of the lip to seal around the carburetor, have you recently pulled the intake boot off only to realize the O-ring behind it is hard & brittle? This kit is your solution to solving some of those mystery problems and make your bike like new again. There can be a great deal of heat that can radiate behind the cylinder head on a DR650 as it is an air cooled engine. With that comes long term maintenance items that will need to be replaced due to them being made of materials that cannot withstand those constant heat cycles indefinitely.

Our kit includes O.E. parts from Suzuki to include:

1. Intake Boot
2. Metal Clamp
3. Premium Japanese O-ring

• Precision engineered to perfectly fit the factory airbox, these filters meet or exceed OEM specifications
• Direct replacement of original equipment filter with no need to change carburetor jets or settings
• Manufactured from world-class materials to achieve optimum performance and engine protection

This is an O.E. replacement diaphragm for your BST40 carburetor.

Geared for the do-it-yourselfer that already has a TM40 or HS40. This kit supplies everything you need to convert it for use on your bike.

Kit includes intake and air boot adapters, throttle cables, choke knob, accelerator pump nozzle, a wide selection of main and pilot jets plus a TM40 tuning manual.

Quality replacement headlight fairing for Gen 1 KLR650.

Available in 4 colors.

Quality replacement headlight fairing for TW200

Quality replacement rear fender from Maier.

The long over-due rally shield for the 2008-on KLR650 is finally here!

Parabellum uses 4 steel brackets mounted to factory locations as well as our stand-off windshield design to ensure the customer doesn’t have to drill extra holes in the cowling but still achieves that iconic upright look of the real Dakar Rally bikes.

The Rally shield protects the rider’s torso/chest from air, cold, roost, branches and bushes while leaving the rider’s head/helmet in clean air. We recommend the Rally shield for riders seeking some protection, but prefer to be off-road.

The Rally shield is made from 1/8 inch cast acrylic and is 11.5 inches wide at the bottom and 17 inches tall.

Zero Gravity windscreens feature the finest optics of any windscreen on the market. All Zero Gravity windscreens are fabricated using highly specialized "vacuum forming" techniques similar to those used to form aircraft canopies. The result is a virtually distortion free optical lens.

Made from the finest grade of acrylic plastic, Zero Gravity windscreens are stretched as they are formed, a process which results in superior strength and flexibility. This flexibility allows the windscreen to absorb road vibrations and resist cracking. All of our windscreens are factory pre-drilled and ready to install. The mounting holes and windscreen profile match the O.E.M. windscreen for a precision fit.

Zero Gravity currently offers three types of windscreens for the new version of the KLR.

SR is the Stock Replacement

DB is the Double Bubble screen

ST is the Sport Touring model.

The DB model is approximately 1.75 inches taller than stock and the ST is approximately 3.5 inches taller than the original. Each screen is available in Clear, Smoke or Dark Smoke colors as well.

New Body Plastics available in Black, White, Carbon Fiber, Dark Blue, or Yellow.

Also, Currently Exclusive to ProCycle: Olive Green, and Desert Sand (complete kit only)

Includes Rear Fender, Side Panels, Headlight Cover, and Front Fender.

Choose a Kit with Maier Front Fender [pic1] or after market SuperMoto Fender (black or white only) [pic2].

• SuperMoto fender kit includes our High Mount Fender Bracket!

Includes new Suzuki side panels, heat shield, headlight cover, rear fender and your choice of aftermarket off-road or supermoto front fender.

Choice of off-road or supermoto (SM) front fender.

Blue kits come with white side panels.

Freshen up the look of your TW. New Plastic in Black or White. Includes Rear Fender, Side Panels, Headlight Cover, and Front Fender.

Choose a Kit with OEM Front Fender or after market SuperMoto fender.

SuperMoto fender kit includes our High Mount Fender Bracket!

Left and right stock OEM Suzuki side panels plastic sold as a pair.

Includes one heat shield. Depending on your application and preferences, more than one heat shield may be useful. Extras can be added here.

Quality replacement front fender from Maier.

Finding the right riding height is super important for maintaining control of your bike at all times. If you feel like your bike sits a bit too high, you'll love the Zeta Anodized Lowering Link! It's a fantastic replacement for your OEM linkage, and it can help you lower your center of gravity, which often translates to better handling and a more comfortable riding experience.

Here are some great features to consider:

-From +5mm to -25mm.

-5 clips to lower. A standard position and 1 clip to lift up. Total 7 clips range adjustment.

- Enhanced ground touch for better stability.
- Adjustable link lets you lower it by about 30 mm, depending on your model.
- Easy bolt-on design—just swap out your stock link rod.
- Crafted from high-quality 7000-series aluminum alloy with a sleek laser finish.

It's time to ride with confidence and comfort!

• Repair kits include all the bearings, seals, shafts and spacers required for a complete rebuild
• Constructed from OEM-quality components at a fraction of the cost

For a top notch rebuild or re-valve of your rear shock use this high quality replacement seal head.

• Complete assembly, ready to install into the shock body
• Has air bleed holes to help remove air from the oil reservoir during installation
• Double-lip oil seal design keeps out dirt and keeps friction low
• Kits include aluminum body, dust seal, bushing, oil seal, O-ring, internal guide bushing/washer, snap ring, and top-out bumper

Low friction 'triple lip' seal design. Oil seals last 3-4 times longer that OEM seals. Kit includes 2 Fork Seals and 2 Dust Wipers.

Now you can have minimum output shaft wear, minimum chain drive wear with the FRITZCO DRIVELINE sprocket. The design of their sprockets provide correct chain alignment, allows for full spline contact with the XR650L's output shaft, fit the counter shaft either way, and straight up no hassle installation with the OEM two bolt retainer and fasteners (except 13 tooth that comes with it's own quick change retainer). Their sprockets are machined from alloy steel that is comparable in every way to OEM Honda and the best offered by other manufactures. The sprockets are then given a heat treatment that provides a compatible sprocket for the Honda output shaft and longest wear life possible.

A way to double the sprockets life would be to have a sprocket that fits on the shaft either way so both sides of the teeth can be used. Bear in mind you can't wear one side of the teeth all the way through, then flip the sprocket, and expect double life. You must reverse when a normal wear pattern develops.

16 tooth sprocket is the biggest front sprocket that will run with the standard 110 link chain and 45 tooth rear sprocket on an XR650L
The OEM cover will require modifying to use the 16 tooth sprocket on your XR650L.

For all years.

• Machined from impact and wear resistant chromoly steel
• Heat treated, then finished with a nickel coating for corrosion resistance

These quality JT sprockets are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.

• Computer-designed to achieve ultimate strength at minimum weight
• JT combines leading-edge technology with top materials to produce the ultimate quality sprocket range with unbeatable value
• Every sprocket meets or exceeds the highest possible quality standards set for the motorcycle industry
• Sprockets are heat-treated and bead-blasted to reduce material surface tension
• Unless noted, rear sprockets made with top-quality-grade C45 high-carbon steel
• Size 38T

• Computer-designed to achieve ultimate strength at minimum weight
• JT combines leading-edge technology with top materials to produce the ultimate quality sprocket range with unbeatable value
• Every sprocket meets or exceeds the highest possible quality standards set for the motorcycle industry
• Sprockets are heat-treated and bead-blasted to reduce material surface tension
• Unless noted, rear sprockets made with top-quality-grade C45 high-carbon steel

Quality steel rear sprockets.

Color may vary based on manufacturer availability, quality will not be compromised.

This kit will replace your stock sprocket bolts and nuts with new hardware.

Factory Honda replacements in a convenient kit.

Choose either a 14, 15, 16 or 17 tooth JT countershaft sprockets.

Go down in tooth count for faster acceleration.

Go up for lower RPMs at cruising speeds.

Quality steel front sprockets. Choose 525 or 520. Also available 'Wide Boss' JTF438 520 sprockets.

  All 520 sprockets require a new retainer plate, please add on if purchasing this size.

High quality steel sprockets.

Stock Gearing: 15/48-128x128

Individual 14T, 15T or 16T front sprockets.

JT Sprockets are made from the latest generation of computer design and control metal cutting equipment for maximum durability. Front sprockets are made from chromoly SCM420 steel alloy. All sprockets are heat-treated and hand-finished to meet or exceed the highest possible quality standards.

JT steel rear sprockets are manufactured using only the finest grade of C49 high carbon steel.

Two styles of rear sprocket were used on the DR350. The 90-95 'S' and 'SE' (street legal) models have a cush drive hub. The 96-99 'S' and 'SE' as well as all of the 'dirt only' models have a non-cush rear hub. Select your sprocket accordingly. If you are not sure, look at your bike. If the sprocket is bolted directly to the wheel hub you have a non-cush model. If your sprocket is bolted to a separate sprocket carrier you have a cush drive model.

Quality JT sprockets are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.

Available in a 15T

These quality sprockets are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.

High quality steel rear sprockets from 39 to 53 teeth.

Sprocket color may differ depending on size.

These masterlinks fit the original OEM Suzuki chain. The original chain is marked DID 525 V8. Choose from Clip Type or Rivet Type.
 

• Protect your DR650 from overheating.
• Inline temp block kit works with Trail Tech computers Striker, Vapor, Voyager, Voyager Pro, and all TTO temp meters. 
• Installs between the oil cooler and top oil supply line, giving a cooled oil temp reading.
• Includes 3 new o-rings, and 2 longer bolts, as well as the Trail Tech m6x1.0 temp prob.

 Warp 9's CNC shark fin rear rotor protector. To make installation super-easy this fin bolts to a brand new CNC machined caliper bracket. Just remove your existing caliper bracket and remove the pins, install them on this new one and then put the caliper and fin back on.

PSR has a new shark fin rear rotor protector for the big XR and XRL. CNC machined from forged aluminum and then anodized gun metal in color. This unit bolts to the stock caliper bracket.

Mount Barkbusters standard aluminum bar handguards to 1-1/8" motorcycle handlebars with the Barkbusters Tapered handlebar saddle clamp set.

What's in the box:

• 4 peice saddle clamp set
• 2 complete saddles

These are all you need to mount your current Barkbusters Handguards when you upgrade to a tapered oversized 1 1/8" handlebar.

Fits Moose and other aluminum hand guards

• Aerodynamic and stylish design
• Protect hands from brush, water and cold wind
• Simple installation
• Sold in pairs

Replace the deflectors on your aluminum bar backbones with Barkbusters VPS wind protection replacement handguards.

For Tapered 1 1/8" handlebar.

Contoured alloy hand guards with inner mounts, allow space for the clutch cable and brake hose.

Note: This kit includes the aluminum handguards only. Plastic deflectors sold separate, can be added by selecting color from drop down menu.

For DR650 or other models with long levers add the optional universal fit Spacer Kit so you don't have to cut the balls off the end of your levers when installing these handguards. (May require additional adjustment or modification on some models.) 

XT250 engine Case Guards.  

These are a very nice addition in engine protection for the XT250.  Made from billet aluminum and steel powder coated bracketry. 

• Essential protection for many late model adventure touring bikes
• Precision built for exact fit installation
• High Strength 25mm diameter powder coated aluminum construction
• All necessary hardware included

A set of replacement brake and clutch levers. Standard length.

Please be sure and order the correct levers for your model year KLR.

Note: Gen 1 levers are black
Gen 2 levers are Silver

CNC Machined high quality aluminum folding levers.

Lever folds outward to prevent breakage in the event of a crash.

Automatic lever position restoration provides quick recovery from the crash.

Ultra precision machine cut for super light weight construction, high precision and quality.

Available in 3 and 4 finger lever lengths to fit your riding style.

Made of durable aluminum for extreme strength. Titanium color anodized finish.

Sold Individually

• Polished aluminum finish
• Quality Aircraft grade A-360 aluminum for strength & durability
• Designed to exceed OEM specifications, built to resist breakage
• Durable hard coating
• Designed to fit OEM perch
• Image is for reference only, actual product may vary for your application

Quality replacement levers. Standard length.

• Polished aluminum finish
• Quality Aircraft grade A-360 aluminum for strength & durability
• Designed to exceed OEM specifications, built to resist breakage
• Durable hard coating
• Designed to fit OEM master cylinder

Quality replacement levers. Standard length.

A quality set of replacement throttle cables from Motion Pro.

The Apollo Heated Grips are designed with an integrated adjustable thumb switch, which allows them to easily fit on any kind of motorcycles on the market. The integrated thumb switch gives control to the rider to adjust the temperature level while keeping hands on the bar for a safer ride.

Its wide temperature setting range will keep the rider comfortable under the cold riding conditions.

The 5 color LED display will enhance the visual look of the heated grips and will allow the rider to quickly know at which heat level the grips are set.

This system will also detect if the battery voltage is too low and will automatically shut down the heated grips in order to make sure the rider have enough power to start the engine or use the motorcycle.

Specifications:

• Integrated thumb switch designed for easy installation and control.
• “Plug & Play” wiring connections to shorten the installation time.
• Wide temperature settings for various weather conditions.
• Low Battery Warning protection to ensure the motorcycle has enough power to start.
• 5 color LED Indicators for the rider to quickly know in which heat level the grips are set.

High Quality Replacement Wheel Bearings and Seals for your TTR125 with disc brakes.

Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.

Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.

Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.

Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.

Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.

The rubber coated outside diameter creates an optimum seal at the hub.

Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.

Contains all of the bearings and seals required to re-fit a wheel.

Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.

Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.

Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.

Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.

The rubber coated outside diameter creates an optimum seal at the hub.

Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.

Choose 17" Supermoto, 19" Adventure or stock 21" front wheel. All work with the stock DR650 speedometer and cable on either the stock or Warp 9 hub.

We start with an Excel rim, OEM hub, and Buchanan's heavy gauge stainless steel spokes. Rims and spokes are precision machined for a perfect match to your bike. Optional upgrades include billet a Warp 9 hub available in 5 colors and SUN rims available in 3 colors.

Our pro shop then laces and trues your wheel to perfection, giving you the highest quality custom wheel available.

• New OEM or Warp9 hub with bearings and seals installed
• 1.60" x 21" Off-Road
• 1.85" x 21" Dual-Sport
• 2.15" x 19" Adventure
• 2.50" x 19" Adventure (Sun rims are 2.75")
• 3.50" x 17" Supermoto

Add a tire to your wheel order and we will throw in a tube and mount and balance it at no additional charge.

Hot Shot Series Honda CDI Box; Rick's aftermarket Hot Shot CDI box has a hotter spark than OEM and retains the stock curve. It will replace OE# 30410-MN9-003 & 30410-MN9-000 and fit 1993-2021 XR650L. *CDI Boxes are not covered under the One Year Warranty.

Antigravity Batteries introduce the ground-breaking "RE-START (RS)" line of batteries. These are the first batteries with built-in jump starting! They intelligently monitor their status, and just before going completely dead, puts itself to sleep with just enough energy to get your vehicle started again. Simply press the RE-START button located on the battery, then start your bike and ride away!

These are an extremely lightweight (2.3 lbs.) and high-powered Lithium-Ion replacement battery for motorcycles. These batteries offer the first Battery Management System (BMS) found on a powersport battery and includes low-voltage cut-off, over discharge, over-charge, and thermal protections with real time lithium-ion cell balancing. Highly recommend using a lithium charger to maintain the life of the battery.

3 Year warranty

Product Size is just 5.9"L x 3.5"W x 3.74"H. If you need spacers, select the optional Foam Kit to pad the battery in the battery box.

Designed to enhance the appearance of your motorcycle, yet provide greater riding distance per tankful. Larger capacity than stock, yet very slim and sleek. Perfect for wherever your adventure takes you! This tank is made from POLYETHYLENE CROSSLINK for extra strength and durability.

DOES NOT FIT NEW KLX300 "R" Models

Iridium spark plugs are made with premium quality materials.

Iridium plugs last longer than standard ones, meaning you won't have to replace them as often.

• The ultimate in the evolution of spark plug technology and performance from an industry leader
• The iridium electrode is 25% smaller than a platinum electrode, and it's just 1/4 the size of a conventional nickel electrode
• Ultra-small diameter center electrode reduces voltage requirement and extends ignition system life
• Metal shell plating has enhanced anti corrosion qualities

Sold individually, unless otherwise stated.

Keep your motor running right with fresh spark plugs!

NGK is one of the world's largest manufacturer of spark plugs, whose products are used as original equipment (OE) on countless motorcycle and automobile models.

• High-quality materials and superior construction for serious power and reliability
  • Pure alumina silicate ceramic insulator provides high strength and better heat transfer
  • Deep-seated copper core for a wider heat range
  • Nickel alloy tip for longer life
  • Trivalent metal plating provides superior anti-corrosion and anti-seizing properties
• Choosing the right high-quality plugs prevents fouling from running too cool and preignition from running too hot
• NGK plugs available for almost every application and riding style

Includes forged JE 89mm piston 10.5:1 piston, Rings, Clips, Pin, big bore sleeve and top end gasket set. You will have to have the big bore sleeve installed in your cylinder and bored to fit the larger piston.

This is all you need to not only change your oil, but protect your motor as well. We include a billet oil drain plug cap, a 5-pack of oil filters, and new O-Rings to replace any you have that may be leaking or worn.

• Billet Oil Drain Plug Cap
• O-Ring Kit
• 5-Pack of Oil Filters

• Stop your expensive helmet from falling and hitting the ground while you’re out riding
• The perfect solution to easily store your helmet with your bike.
• 7075 T6 machined aluminum
• Fits all 7/8 handle bars
• Includes 2 stainless screws
• Fits virtually all bikes and makes ( except Harley )

Don't get burned! Giant Loop's ingeniously simple and effective exhaust shield protects bags and bodywork from heat damage. The Hot Springs Heat Shield helps avoid the meltdown, preventing bags and side panels from touching your bike's exhaust. It's the lightweight, universal heat problem-solver for virtually any motorcycle exhaust system. Backed by a Limited Lifetime Warranty.

• Eliminates the need to cut and splice wiring when using aftermarket turn signals or marker lights
• Plug into the OEM turn signal plug and then use bullet style connectors used on aftermarket lights
• To verify proper fitment, compare connector photos to OEM connector
• Sold in pairs

This new and improved DOT kit includes LED headlight assembly with plug-and-play wiring harness, a specially designed adjustable steel mounting bracket, and all the required installation hardware. No cutting, no drilling, no wiring modifications! Installation takes 5 minutes.

We highly recommend this kit over the non-DOT and original DOT kit.  The low beam has extra punch and a proper beam pattern cut-off.  The high beam throws light far and wide.  It’s already a crowd favorite!

Two colors to choose from, Chrome or Black. Light output and beam pattern are the same for either color.

Low Beam: 20W, 2,800 Lumens
High Beam: 35W, 3,600 Lumens
Color Temperature: 6,000k
DOT & SAE Compliant
CE, RoHS, ISO9002, IP67

Please note: Fits '87-'07 (Gen 1) only

Nitro Tape is a self-fusing silicone tape that's easy to remove with no residue.

It is waterproof, stretches up to 300%, has a temperature range from -65° to 500°F and insulates 8,000 volts per layer.

It resists UV, salt and corrosive chemicals.

20 mil thick, 1" wide by 10' long.

If you've split a radiator hose, this can help. A 'must have' for all tool kits.

• Reduce exhaust sound by one to six decibels
• Options for DG V2 & RST and for the older "O" & "R" Series mufflers
• Easy installation; remove rear end cap and place Quiet Core in front of the spark arrestor
• Smaller diameter inserts are quieter but more restrictive; larger inserts are less restrictive but louder
• 1" Not recommended for RST
• Each size is sold separately

The new DG RST (Reduced Sound Technology) muffler is the quietest DG muffler and is designed especially for dual-sport machines (Just 84db @ 3200 RPM). 

A new baffle design dissipates sound waves reducing noise output in a very efficient manner. This new design also stretches out the time between muffler repacks. 

Included is a Stainless Steel mid-pipe, USFS Approved Spark Arrestor and a new Aluminum end cap. The installed weight is approximately 7.7 lbs.

This is a great Dual-Sport tire from Dunlop. Designed for the true 50/50 rider. An Adventure product for the price-conscious customer. Full tread depth pattern designed for rigorous off-road use yields excellent traction on everything from hard-packed fire roads to soft single-track trails. Versatile tire performance allows riders to travel on the street and venture off-road. A tire equipped to go anywhere, the D605 is a value option for the all-around rider. DOT approved.

Shinko 700 Series tire features an aggressive 60% on-road and 40% off-road read pattern for good dirt riding performance, without sacrificing pavement grip. Other features:

• Aggressive tread pattern with drop lug construction
• Heavy-duty 4-ply carcass for durability
• Reinforced side knobs for cornering stability
• DOT approved

We offer two different types of SuperMoto tubes. The first are Standard Tubes and are meant to be used with standard bias-ply type tires, but can be used with radial tires also.

But, if you are running radial tires, like SuperMoto, or have a retro bikes with spoked wheels and radial tires, you probably want to run the 'Radial Tubes'. Front tubes fits 120/70 and 120/60 tires. Rear tubes fits 150/60, 150/70 and 160/60 tires. These have a metal valve stem.

Slime Tube Sealant is formulated and tested for use in all tube tires. Once installed, Slime remains liquid and will not harden or dry out. Slime is guaranteed for 2 years.

As the Slime treated tube rotates, centrifugal force pushes the sealant to the tread area creating a layer of protection, repairing punctures as they occur and treating existing punctures. Slime is not intended for use in tubes losing pressure from sidewall punctures, bead leaks, damaged rims or faulty valves. Slime for tube type tires is not recommended for use in tubeless tires.

• Prevents and repairs punctures up to 1/8"
• Remains liquid inside the tire, coating the tread area as the tire rotates
• Non-toxic, non-hazardous, non-flammable, non-aerosol and water soluble
• Tubes treated with Slime can be patched with a conventional vulcanized patch using a bit of patience and care

Sintered Pads from EBC are the best pads we have found for the KLR, they provide good performance in all conditions yet still give you long pad life.

These sets include front and rear brake pads.

SMX Carbon Look Rotor

• Rotor material has higher friction than plain stainless steel for added stopping power
• Rotors measure 320mm
• Come with caliper relocation bracket
• Designed to fit standard hubs

EBC rear replacement brake rotor. High friction billet steel.

Quality components at a great price.

• Standard Kit: Includes SS braided lines and EBC sintered brake pads.
• Standard Plus Kit: Includes SS braided lines, EBC sintered pads and an EBC Carbon Steel front rotor.
• Super Plus Kit: Includes SS braided lines, EBC sintered pads and EBC carbon steel front and rear rotors.
• Deluxe Kit: Includes SS braided lines, EBC sintered pads and an EBC Premium 320mm SM front rotor kit.
• Super Deluxe Kit: Includes SS braided lines, EBC sintered pads, an EBC Premium 320mm SM front rotor kit and EBC rear rotor.

GBrakes Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.

The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.

• Significantly improves response and feel over factory rubber lines
• Largest performance improvement for your money over any other braking upgrade
• Stainless steel hose resists abrasion and puncture
• Teflon core does not degrade over time like rubber lines
• PTFE Dupont 64 Teflon® hose
• Feature a heavy-duty stiffener sleeve and route just like the factory lines
• Proprietary, premium fittings
• Banjos utilizes a unique machined channel and sealing surface for leak-free installations
• R&D and engineered in the USA
• GBrakes USA controls the manufacturing process, ensuring the highest level of quality control

All the parts you need to freshen up your brake master cylinder. New piston, seals, return spring, boot and snap ring.

Made by Nissin, an OEM supplier in Japan

*Rear fender with minor superficial scratches on the top of the fender, most likely not visible unless looking up close, and some will be covered when installed. Sold as is. Includes all pieces for complete rear fender kit.

ProCycle Plastics (formerly DSA) Rear Fenders include LED tail/brake light and license plate holder. Vacuum molded, these parts are a design improvement over stock.

• Innovative multi-use tire tool set
• Breaks the bead on most street and off road motorcycle tires
• Integrated tire spoon for tire removal and installation
• Light weight and compact size is perfect for tool packs
• Ergonomic handles with crossguard to keep hand from riding forward
• Forged 7075-T6 aluminum construction for strength and durability
• Black anodized finish
• Patent pending

Available in 9.5" aluminum (ideal for travel) and 16" forged steel (useful in a home shop/garage)

• CNC laser cut from light weight 1/8" 5052 Aluminum
• Easy installation, no modifications required
• Large 12" x 9" surface area
• Sleek low profile, and lightweight!
• Rigid 4 point mounting system
• RotoPax 1 gal or 1.5 gal compatible

You may purchase just the rack or you can order the Rack with the RotoPax Mount. If you really want it all, you can order the Rack, Mount and a Fuel or Water Container.

Wide Adventure rack for the WR. Precision laser cut from .25" 5052 aluminum then powder coated black with a shot peened look. This rack is 11" x 17.5" and has numerous tie points for straps or bungees to secure a load. It is pre-drilled for a RotopaX mount. Easy installation means it is bolted to the bike in 10 minutes. There is some minor drilling of the plastic to be done. All necessary hardware and complete instructions included.

DRZ400 rack is available in both a Utility and Sport version. The Sport version is 9" x 9" and the Utility is a full 2" longer for added storage space. Both of the S/SM racks have tabs so you can bolt the stock tool bag on.

Please select the rack for your specific model as the differences are significant

• Fully welded construction from 16 gauge mild steel
• Powder-coated black textured finish
• Rigid 4 point mounting system (except off-road model rack)
• Hardware and detailed instructions included

PMR side utility racks are great for strapping down your soft luggage and keeping it off the rear plastics and exhaust pipe, while adding plenty of new tie down points for any luggage you have on your seat or tail section. They also add an enhanced level of security and strength to the rear end of your motorcycle in the event of a tip over or crash. 

Sold as a pair.  Easy to Install

• Complete with all necessary mounting hardware
• Fabricated with 1/2 inch steel tubing, MIG welded
• Finished with a semi gloss black industrial grade powder coat
• Comes with left and right side racks, each side weighs 2 lbs

The CRF300L side racks are intended to work hand in hand with their ENDURO Series rear rack. 

If you plan on installing the side racks without their rear rack, you will need the spacer kit to fill in the empty space, which we will send to you at no extra cost. Please select the option when you place this in your cart.

Please note that you will need to remove the left side rack to access your lockable factory storage hatch.

Giant Loop Pannier Pockets are a minimalist version of tank panniers that expand front-of-bike storage while staying out of the rider’s way. 

Pannier Pockets integrate seamlessly with the harness on Giant Loop’s Fandango and Diablo Tank Bags or can be mounted independently with an included webbing strap. 

Connect them across the middle with the sides strapped to tank, shrouds, or engine guards with a Buckin’ Roll Tank Bag installed.

• VOLUME: 4 liters (244 cubic inches) total volume (two 2-liter pockets)
• DIMENSIONS: 10” L x 3.5” W x 4.5” H (25 cm L x 9 cm W x 11 cm H).

TW200 billet oil drain cap plug. 

Nice billet aluminum replacement for the old cast oil drain cap.

Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm. Lo-pegs are down and back 1/4".

Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm. Lo-pegs are down and back 1/4".

• Light enduro footpeg with enhanced grip
• Mounted with popular RGK2 peg joints
• Tread on footpegs offer a secure hold even with heavy boots
• Includes two footpegs and two bike specific turning joints
• Notches dynamically adapt to the weight shift by being able to move forwards or backwards with an intelligent dampening system
• Unique serrated structure ensures reliable slip protection and allows unrestricted concentration on the road
• Innovative rubber bearing between the tread and the joint means basic vibrations are absorbed and shocks on uneven terrain are mitigated
• Dynamic adaptation to foot movements
• Enhanced safety and riding enjoyment

This anodized billet piece, brings a touch of color to your bike. Available in red or blue, it replaces the stamped steel clevis that connects your brake pedal to the master cylinder.