Tapered roller bearings provide decreased maintenance, less wear, smoother operation and longer life.
This set of high quality replacement steering stem bearings includes:
Pivot Pegz have set a new standard in footpeg performance and quality and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty. Pivot Pegz aim is to build the best footpegs in the world and they really do perform as good as they look. Here's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever!
These top of the line Adventure pegs from Warp 9 are 5" long and 2.5" wide. They will give your feet the perfect perch whether you are cruising down the highway or standing up hammering down a singletrack trail.
For the frame drain on your XR650L ,extra protection for your motor! Strong magnet at the end of the plug picks up metallic flakes in your oil, protecting your engine!
Adventure bike heaven is off-road headed down a dirt road or a trail. If that is your dream, then as you know, you are going to fall. Sometime, someplace, it will happen, so be prepared! Save your bike before it happens.
SW-Motech makes some of the finest protection equipment available. The set-up for the Twin is available in a standard black powder coating or a semi-polished Stainless-Steel tubing. Both sets will protect the vital components of your motorcycle as well as you from damage incurred during a fall, slide or crash. They will preserve the frame, radiator, bodywork and other critical components from touching down with robust tubular steel. The black kit uses 27/21 mm tubing while the Stainless uses straight 22 mm tubing throughout.
Both configurations have a tight fit for great ground clearance and are designed to work seamlessly with other SW-Motech products like their Skid Plate/Engine Guard and SW-Motech Hawk light mounts. Three secure mounting points per side provide the necessary support that make these so strong. There is no drilling, cutting, welding or any other modifications required for mounting but still allows access to the oil filler, tool box and battery. Kit includes all necessary hardware and instructions and an aluminum cover to replace the OEM plastic cover at the lower mounting point on the left side.
Please Note that these Crash Bars are also compatible with the SW-Motech Skid Plate and the SW-Motech Centerstand.
This durable, steel crafted SW-MOTECH Upper Crash Bars Engine Guard protects the tank, fairing and radiator of your Tenere 700 from damage caused by either debris on the road or a crash.
The tough-built, steel constructed bars can ONLY be mounted with SW-MOTECH Lower crash bars (sold separately).
Each engine guard is powder coated black for a sleek finish which remains durable after prolonged use and protects against corrosion caused by the elements.
Features:
Enjoy maximum protection and durability with an SW-MOTECH skid plate. Fully welded aluminum construction is engineered in Germany to provide proper protection from impacts, abrasions and projectile debris. Multiple ventilation slots on the front, sides and bottom of the skid plate permit maximum air-flow to keep your motor cool. Drilling, cutting, welding or any other permanent modifications are not required.
Features:
What's in the box:
The X-Factory Handguards from Acerbis are designed with a steel bar encased in an injection-molded Nylon composite. A replaceable dual-injected polypropylene shield attaches to the bar, providing excellent protection against debris and harsh conditions.
Included with the handguards is a universal mount kit, enabling installation on either 7/8" or 1 1/8" handlebars.
Will not fit XT250 with stock handlebars (oversize bars ok). Recommend Acerbis Rally Pro X-Strong to clear master cylinder.
Made with heat-treated carbon steel for longer wear life and reduced galling. Stock size, simple bolt-on procedure.
Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
Seal profile is engineered to create equal pressure in each seal lip; equalized seal pressure creates less drag and longer seal life.
Patented MAX-LIFE has a coefficient of friction up to 3 times less than the OEM seal material
Triple-lip seal design
Dyno-tested to last 3 to 4 times longer than OEM seals
Directional ribs allow seal to be installed easily
Kits include fork seals and dust wipers
Sized perfectly for adult back-yard racing or fast/aggressive mini riders. This is the most important upgrade you can make for an adult sized rider. The stock suspension is too soft for most adults and aggressive kids. Fits stock shock.
The correct spring rate for your weight will give a smoother more controlled ride. No more bottoming out, and improved traction and confidence off-road.
8.6 & 9.6 springs require an adapter which is included.
Recommended rates:
*Spring color may vary due to specification requirement and availability.
The complete shock upgrade kit - a shock spring of your choice, Race Tech Gold Valve kit, detailed instructions and a bottle of quality shock oil to complete the job. Everything you need to transform your mushy stock shock into suspension that really works.
Recommended rates:
DRZ400 E/S
A pair of Race Tech fork springs to dial in your front suspension to suit your weight.
Fits all DRZ400 models with conventional forks (not for SM)
Recommended spring rates:
| Rider Weight w/gear lbs. | Spring Rate |
|---|---|
| 90 or less | .42 |
| 90-119 | .44 (stock) |
| 120-150 | .46 |
| 150-180 | .48 |
| 180-220 | .50 |
| 220-250 | .52 |
| 250+ | .54 |
This complete fork upgrade kit includes stiffer fork springs and Race Tech cartridge emulators, as well as a set of top quality fork seals and fork oil to complete the job. Everything you need to transform your mushy stock forks into suspension that really works.
You can select from various straight rate springs to customize the package to your needs.
The complete fork upgrade kit - your choice of springs and Race Tech Gold Valves. Also includes a set of top quality fork seals and 5W fork oil to complete the job. Everything you need to transform your mushy stock forks into suspension that really works.
You can select from various straight rate springs to customize the package to your needs.
Stock Spring Rate for XR650L: 0.44 kg/mm
Lightweight, for reduced unsprung mass. Straight rate springs will give better control in the rough stuff. Sold in pairs.
A quality foam Air Filter to replace the stock one. Uses the same guide and frame as the stock unit. It requires foam filter oil to properly trap dirt particles. Don't forget the Evolution Air Filter Oil kit from No Toil.
Based on the wildly popular Race Tech Suspension Seminars taught by Paul Thede around the world, this step-by-step guide shows riders how to make their bikes handle like the pros. Thede gives the lowdown on all types of suspension, including cartridge and non-cartridge forks as well as dual-chamber and nitrogen-charged shocks.
The three forces of suspension, testing procedures, even the black arts of chassis geometry: This explains it all. The book provides step-by-step photos of suspension disassembly and assembly as well as a detailed troubleshooting guide for dirt, street and track.
Revolutionize your riding experience with Swiftkicker.
An adjustable kickstand for your motorcycle. Swiftkicker is built for offroad motorcycles, dual sports, and dirt bikes. Designed with the idea in mind that motorcycles should be able to take you anywhere, the Swiftkicker motorcycle kickstands help you do just that. You can set the length to anywhere in a six inch range of travel so you can stop anywhere without having to worry about having an even surface to park.
With just a flick of your toe, you can adjust the kickstand to the desired height, park your motorcycle, and be on your way.
No longer will you have to search for a rock or piece of wood to prop your motorcycle up with, or even worse, coming back to your bike to find it has tipped over from unstable ground.
The Swiftkicker is 100% manufactured in the USA from the highest quality components.
The billet 6061 head and the hard anodized tube are significantly stronger than the stock stand. An oversized foot will assure that the end of your stand stays where it belongs, rather than eight inches underground with your bike lying on top of it. The design is trail proven in the harshest possible conditions. Because nothing is indestructible, any of the kickstand components are replaceable at a lower cost than purchasing an OEM kickstand.
Measured from the center of the pivot to the bottom of the foot.
High Quality chain. Will need to be cut to fit your sprocket combination.
All of these chains come with a clip type master link.
Fully encloses the chain to guide it onto the rear sprocket. Stainless steel hardware, anodized aluminum plate, and plastic buffer for low friction and noise. Saves expensive engine cases.
The chain slider protects the swingarm from contact with the chain. Replace yours before it wears through to the swingarm.
Heavy-Duty clutch springs
The Total Tune-Up Kit. All the parts you need to do a complete tune-up on your beloved beast.
This is the gasket used between the header pipe and the stock muffler. This gasket is not needed for aftermarket mufflers!
The PowerBomb is a four-stroke header that incorporates FMF's patented PowerBomb module at a precise location in the initial stage of the header. By positioning this "Bomb" at a key point in the system, increased performance and flow is achieved through the expansion and contraction of exhaust sonics through the system with a flow increase of nearly 10%!
Limited Quantity Available
The RS-2 is a potent and versatile design that evolved from their original TRC, engineered to provide increased power delivery. With a different pyramidal shape that features increased volume, the RS-2 is a quieter system with a larger core — and it offers the added bonus of outstanding performance in a value-priced package.
We recommend Anti-Seize on exhaust fasteners
Their rear racks are great for adding the extra storage needed for your next adventure. They are the perfect size for a backpack or small duffel bag. Their steel racks are built to handle any riding style you throw at them, now Rotopax ready! This is the ENDURO Series XT225 Serow rear rack which measures 10 inches wide and 12 inches long.
Easy to Install
Simple, lightweight rack made from rugged 1/8" 5052 Aluminum, with a rigid 5-point mounting system.
Low profile allows for easy seat removal.
Features:
Note: Placement of this top rack does require removal of the stock tool bag.
Simple, quick installation of this 1 pound rack made from rugged 1/8" 5052 Aluminum. A rigid 4-point mounting system, but still sleek and low allowing for seat removal with no hassles.
Features:
DRZ400 rack is available in both a Utility and Sport version. The Sport version is 9" x 9" and the Utility is a full 2" longer for added storage space. Both of the S/SM racks have tabs so you can bolt the stock tool bag on.
Please select the rack for your specific model as the differences are significant
You can add the double D ring loop to any 1" flat webbing system. This simple piece adds a lot of flexibility to any luggage system you are using. Instantly and easily create a mount point or adjustment point on almost anything. Double D Rings can be used as a secondary buckle and works the same way as a helmet strap. However, the double D rings should NOT be used as a primary means of securing luggage.
Available in 6 colors.
CONSTRUCTION FEATURES
Stamped from heavy gauge stainless steel, Giant Loop® Mounts bolt onto virtually any motorcycle, snowmobile, snow bike, ATV, UTV, SxS, 4×4—and even boats. These mounts help keep straps away from hot exhaust while shortening strap lengths for maximum stability and helps make installation of Giant Loop Saddlebags, Panniers, Dry Bags, and Tank Bags even easier.
Sold as a set of two (2).
Replacement shift lever with folding tip.
OE style clutch lever.
Replace your Bent or Broken Levers.
TW200 fitment 1987-2000 year models with Drum Front Brake or 2001-2014 year models with Disc Front Brake.
Matte black 118mm x 85mm mirrors. Similar to stock size.
• 8mm thread
Sold In Pairs
Replacement Inner Tubes for your VanVan or TW200. Always a great idea to carry a spare on your adventures as the rear tube is often hard to find.
This is a great Dual-Sport tire from Dunlop. Designed for the true 50/50 rider. An Adventure product for the price-conscious customer. Full tread depth pattern designed for rigorous off-road use yields excellent traction on everything from hard-packed fire roads to soft single-track trails. Versatile tire performance allows riders to travel on the street and venture off-road. A tire equipped to go anywhere, the D605 is a value option for the all-around rider. DOT approved.
The 244 Series Dual Sport street and trail tires were designed to be equally at home on dirt or pavement. Great value.
The Shinko 244 is a very popular tube-type upgrade for the front tire on the TW200 or the VanVan. DOT approval coupled with excellent performance both on and off-road make this tire a winner!
The 244 Series dual purpose street and trail tire is designed to be equally at home on dirt or pavement.
Available in 5.10-18 (69P load / speed rating) and 4.60-18 (69S load / speed rating).
High Quality Replacement Wheel Bearings and Seals for your TW200.
Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.
Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.
Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.
Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.
Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.
The rubber coated outside diameter creates an optimum seal at the hub.
Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.
| Description | QTY per Kit |
| Ball Bearing | 2 |
| Seal | 1 |
The tension system integrated in this loop is a Green Chile innovation. Their elastics are custom woven inside tubular nylon webbing. This gives you all of the advantages of adding tension to a strap while maintaining the full strength of nylon webbing. You can add their cam buckle tension loop to any 1" flat webbing system and have an instant upgrade.
CONSTRUCTION FEATURES
Patent Pending
Construction Features:
This is a standard H4 bulb that has a 80 watt low beam and a 100 watt high beam. This is an easy lighting upgrade that should not over tax a stock charging system.
This kit includes the all new Morimoto 4×6 LED headlight and pre-assembled JNS Engineering adjustable mounting bracket set. It’s a one beer, plug & play installation.
This is the best performing and highest quality headlight they currently offer.
The low beam pattern is bright, very uniform, and features a proper upper cut-off (Left Hand Drive, ie USA).
The high beam is amazingly bright eliminating the need for auxiliary lighting.
The materials, construction, and aesthetics are all top notch. You won’t be disappointed!
Low Beam: 20W, 2,400 Lumens
High Beam: 35W, 4,300 Lumens
Color Temperature: 5,000k
DOT Compliant
Beam Pattern: Left Hand Drive. (USA)
This USB device connects to a battery cable with an SAE connector just like the typical Battery Tender outlet, and allows you to charge your electronic devices. Input is 12 Volts, with an output to the USB port of 2.1A maximum, perfect for your phone or other USB devices.
32-Blade Dual-Reading Tapered Combination Feeler Gauge Set
Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a plusher ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.
Complete seats are built by Seat Concepts on a new seat pan and come ready to be installed on your bike.
| Width: | 10" (254mm) |
| Height: | Same as OEM |
This optically clear headlight guard is CNC cut for a perfect fit. It is made of durable aircraft grade 3/16" thick cast acrylic which resists harsh rock impacts, trail scuffs, and incidental scratches. Velcro fasteners hold the guard firmly in place and allow for easy on & off should it need an occasional cleaning. Installation is a quick five minute job, positioning template included.
