Replace your handlebar mounted choke with this simple knob mounted directly on the carburetor.
Available in short or long reach.
Long reach is easier to use while wearing riding gloves.
Works for either the stock BST or Mikuni TM40.
High-performance, high-flow filter element and filter base for the TT-R 125.
Sold in 6 packs
Not legal for use on pollution controlled vehicles in the state of California.
Allows your bike to breathe much better giving you better response and performance.
The OEM foam secondary filter can deteriorate rather quickly. Once that happens, it can allow enough dirt into the engine to do significant damage. Replace your filter now with a high-quality foam filter from industry leader Twin Air.
This filter needs to be oiled like any air filter to work properly.
Only for bikes with the stock BST40 carburetor!
Unsurpassed in airflow, dirt stopping and overall performance. Adding a pre-filter to your intake system gives you extra protection from damaging contaminants.
Tune your stock carburetor for better power and response, easier starting and quicker warm up. Mikuni main and pilot jets.
Designed for use with stock engines using either stock or aftermarket exhaust and air filters.
Replaces the stock 2 wire Ruckus fuel level unit with a 3 wire unit that allows use of a multi-level fuel gauge.
Most fuel injected systems are very lean in their stock configuration. This is good for economy and emissions, but not performance. This unit allows you to adjust the Fuel/Air (F/A) ratio without remapping the ECU and getting into complicated software programs. The PowerJet Fuel Controller allows you to adjust the fuel map from -4% to +10% by selecting one of 10 built-in settings (including stock).
The device works by measuring the outside air temperature very close to where the stock sensor is located and then adjusts the signal from the OEM air temperature sensor to the ECU to make use of the Air Temperature Correction factor that is built into the stock ECU. The ECU is told that the intake air is a little cooler than it actually is and it responds by richening the injection map very slightly. How much depends on your setting on the PowerJet. This will result in improved throttle response, especially if you have an aftermarket exhaust of any kind.
PowerJet is easily installed by plugging it in between the stock AIT sensor and the bike's wiring harness under the seat. This can be done very quickly as they are exactly the same plugs. Unplug the stock connection, plug in the PowerJet on each side. The PowerJet fits easily under the seat behind the battery as it is rugged and waterproof. PowerJet comes with a full one year warranty.
Replace the worn slide guide in your stock Mikuni BST carburetor before it causes additional wear to the needle and needle jet. There are wear indicators on the slide guide that help you recognize when it is time to replace your slide guide. New O-ring included.
A new slide for the stock Mikuni BST carburetor.
Direct replacement for the stock spring and exactly like the old Merge Racing spring. Gives a much more consistent accelerator pump squirt. Eliminates the need for the 'O-ring mod', wire or zip-ties on the pump arm. Fits all Keihin FCR-MX carbs except '07-'08 CRF250/450.
Not for the stock DR650 carburetor Fits FCR-MX conversion Only
Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.
Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.
Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.
Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.
Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.
The rubber coated outside diameter creates an optimum seal at the hub.
Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.
| Description | QTY per Kit |
| Ball Bearing | 2 |
| Seal | 2 |
No longer need your speedo drive? Install an electronic unit? This CNC machined aluminum unit will replace the stock speedo drive on the front wheel keeping things properly spaced and sealed up.
To suit a 20mm Axle.
Before placing your order please ensure you check the diameter of the axle, as the earlier models may have different sized axles.
The plastic fitting that secures the stock choke cable to the carburetor is delicate and easily broken. A broken fitting can cause hard to solve idling and running problems.
CNC machined from billet aluminum and anodized black or blue. If you want to retain your handlebar mounted choke this may be the solution.
These no longer fit the new version of the ProCycle Remote Choke Cable. Will not work with the long or short reach choke knobs.
The indestructible, yet lightweight steel tube construction offers the best angle and ground clearance, makes it easy to jack up and provides stability - whether it's during maintenance or on the road. In most cases, you will no longer need to buy an additional swing arm stand. During long downtimes in the winter months, the centerstand helps take the load off your tires.
The IMS Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping.
They are the original Cast 17-4 Stainless steel pegs that revolutionized the foot peg market.
These pegs are 50mm(1.95") x 78mm(3.1").
Pegs Sit at Standard/OEM Height
This is the ultimate adventure bike platform, it measures 2.25" wide, 4.75" long.
Patented adjustable collars make it easy to run them in the stock or lowered positions on most bikes.
Gain more room for bulky boots, or for longer legs. Fastway Adventure pegs come with two sets of F3 cleats, one standard, one long. Kamber bolts lets you adjust the 'tilt' of your pegs to increase comfort, or to give better squeeze on your bike.
Kit includes required fit kit.
Double the size of your side stand footprint and half the chances of your KLR tipping over when parked on soft terrain. This laser cut, TIG welded 0.190" thick slice of aluminum bolts to your machine with just the addition of a hole in the stock side stand pad. Just takes minutes to mount.
Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a more plush and active ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.
These features combine to offer a custom seat feel, and provide greater enjoyment and increased range on a long commute, or Dual-Sport ride!
The Complete Seats come assembled with an aftermarket pan and ready to ride.
"Will not fit the Rally model"
| Width: | 10 3/4" (273mm) |
| Height: | Same as OEM |
Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a more plush and active ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.
These features combine to offer a custom seat feel, and provide greater enjoyment and increased range on a long commute, or Dual-Sport ride!
| Width: | 9" (229mm) |
| Height: | Same as OEM |
Kit includes all the fork bushings, o-rings, snap rings and washers. This kit comes with what you need to completely rebuild your front fork bushings.
Kit includes all the fork bushings, o-rings, snap rings and washers. This kit comes with what you need to completely rebuild your front fork bushings.
Low friction 'triple lip' seal design. Oil seals last 3-4 times longer that OEM seals. Kit includes fork seals and dust wipers.
Seal profile is engineered to create equal pressure in each seal lip; equalized seal pressure creates less drag and longer seal life.
Patented MAX-LIFE has a coefficient of friction up to 3 times less than the OEM seal material
Triple-lip seal design
Dyno-tested to last 3 to 4 times longer than OEM seals
Directional ribs allow seal to be installed easily
Kits include fork seals and dust wipers
Both kits include all bushings, snap rings, and washers.
Gen 2 kit also includes the necessary O-rings.
Gen 1 kits are OEM bushings, snap rings and washers.
Complete kit to replace the bearings and seals in the DR350 shock linkage. Includes the lower shock bearing.
| Kit Contents: | |
|---|---|
| Spherical Bearing | 1 |
| Snap Ring | 2 |
| Seal | 6 |
| Needle Bearing Shaft | 3 |
| Needle Bearing | 5 |
Damping Rod style forks are notorious for being too harsh, too mushy and too easy to bottom. Gold Valve Cartridge Emulators remedy this problem by controlling the compression damping with a tuneable valve. The Emulator sits on top of the damping rod and is held in place by the main spring.
Simply put; Emulators make damping rod forks perform like well-tuned cartridge forks. Installation and tuning for any condition or rider preference is very straight-forward.
Simple to install and completely tunable for all conditions and rider preferences.
Link lowers the rear of the bike by 7/8".
Comfortable at a stop or on technical trails.
Installation takes about one hour, and only a few minutes more to drop the forks in the front to match.
Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.
Kouba lowering link will lower the rear 1.75". Comes with bearings and seals installed for a quick and easy installation. Instructions included.
Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.
7.48mm diameter - Includes three valve shims of each size from 1.20 to 3.50mm in .05mm increments.
141 shims in total. 0.57 cents per shim! Does your local dealer have the shims you need?
A set of four high quality valve stem seals.
Outer Clutch Cover O-Ring, Inner Clutch Cover Gasket, Stator Cover Gasket.
Sold individually, not as a kit
285cc big bore kit includes:
Wiseco piston 78.00/+5.00 10.5:1 (with rings, pin & clips):
HotCams stage 1 camshaft:
Complete top end gasket set:
This is a great combination and a big 'bang for the buck' performance increase.
No re-sleeving required. You will have to have your cylinder bored to fit the larger piston.
ProCycle 440cc BIG BORE 89mm KIT 2 With Cam Complete kit with 11:1 Wiseco piston (with rings, pin & clips), big bore cylinder sleeve, HotCams stage 3 camshaft and top end gasket set. You will have to have the larger sleeve installed in your cylinder.
Superior Filtration:
This should be the last oil filter you will ever buy. Made from laser cut, medical grade, 304 stainless steel micronic filter cloth, this filter provides 200% more filter area than other filters in many cases. Most good paper filters will pass particles in the 90 to 95 micron range, and some tested, as much as 300 microns. Sand is about 125 microns and a white blood cell approximately 25 microns. Scott's stainless filter catches items down to 35 microns "absolute". The pleat seam is welded, able to withstand up to 600 degrees, not glued, like paper filters.
Providing unbeatable performance and exceptional value, Hi-Flo is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide.
Grab our 5-pack and save both time and money!
A pair of factory OEM o-rings for the valve covers. Your valve cover o-rings live in one of the hottest parts of the engine and have a pretty short life. Replace them on your next valve adjustment to prevent oil leaks.
Time to adjust your valves? Here are the O-Rings that fit in your Valve Covers on your Yamaha. Keep the oil inside your motor and grime out! This kit includes both O-Rings. Be sure to grab the feeler gauges and a special wrench to aid in adjusting your valves.
Includes all necessary top quality gaskets, and seals for engine rebuilds.
OEM valve cover o-rings
In this kit you will get 4 factory replacement bolts to replace any broken or damaged clutch pressure plate bolts on your DR650.
It can be easy to over torque these bolts if not done properly. If one of these bolts is damaged on your DR650, we highly recommend replacing all 4 to prevent any future failures down the trail.
Raises compression from stock 9.5:1 to 10.5:1 for more power and snappier response. Highest quality Wiseco pistons are forged in the USA. Fits the standard size stock bore.
As with any engine or exhaust modification, you will need to re-tune your fuel delivery system for optimum performance.
Chain slippers undergo degradation over time due to friction associated with the chain's movement. To maintain optimal operational performance, it is advised to replace worn components with authentic Honda parts.
Chain guides experience degradation over time as a result of chain friction. To ensure optimal performance replace worn components with genuine Honda parts.
Genuine Kawasaki replacement chain guide. This guide mounts to the lower swing arm.
Chain sliders may undergo degradation over time due to the friction produced by the chain's movement. Restore optimal performance by utilizing this authentic Yamaha component.
The new DG RST (Reduced Sound Technology) muffler is the quietest DG muffler and is designed especially for dual-sport machines (Just 89db @ 3200 RPM). A new baffle design dissipates sound waves reducing noise output in a very efficient manner. This new design also stretches out the time between muffler repacks. Included is a Stainless Steel mid-pipe, USFS Approved Spark Arrestor and a new Aluminum end cap.
You may want to consider a new exhaust gasket that goes between the header and the muffler.
The Powercore 4 spark arrestor muffler. FMF developed the Powercore 4 to increase the horsepower and torque throughout the entire power curve. Highest quality packing for long life. Removable spark arrestor included. Louder than the Q4. Approximately 99db stock or about 94db with optional Quiet Insert installed.
Our very own high flowing head-pipe is made in the USA using a CNC (computer numerically controlled) mandrel bender for an absolute perfect fit. It is a high quality 3-piece welded two into one, stainless steel head-pipe.
The SS Pro-Flow is a tested upgrade over stock that will bolt right on with no modifications needed.
We recommend a new exhaust gasket when installing your new SS Pro-Flow.
Protect your Kawasaki KLX250 or KLX300 with T-Rex Racing's heavy-duty skid plate engineered for maximum durability and performance. This premium aluminum skid plate shields your bike's engine and undercarriage from rocks, roots, and trail debris during aggressive off-road adventures.
Precision-manufactured for perfect fitment, this bolt-on protection features reinforced mounting points and lightweight construction that won't compromise your bike's agility.
Easy installation with included hardware makes this essential upgrade perfect for trail riders, enduro enthusiasts, and dual-sport adventurers seeking reliable undercarriage protection for their Kawasaki motorcycle.
Radiator guards from Devol Racing protect your radiators from damage due to trail side objects and roost bullets. They offer protection not just from frontal assaults but also from those tricky side attacks. Made from high-grade aluminum alloy for light weight and strength, these guards have an improved air-flow design that eliminates any overheating problem. A solid mounting to the frame make these stronger than most guards that just mount to the radiators themselves.
Devol Racing makes a super product that will keep you on the trail for a long time.
The touring windshield from Parabellum has been designed, developed and tested using all the knowledge and experience of the KLR riders in their own shop. Using the stock mounting points as well as the cowling mounts increases the rigidity of the shield.
All new fasteners are included. This new design allows you to move your handlebar to different positions and will not interfere with a stand-up position for off-road use.
This shield is constructed of 3/16" military grade cast acrylic that is 17 inches wide at the bottom tapering to 16 inches at the top.
Windscreen attaches to your bike's handlebars. Fully adjustable mounting brackets. Includes 7/8' handlebar clamps. 14" tall & 10" wide.
Will not fit 1 1/8" oversize handlebars.
High-quality, direct replacement plastic kit includes:
Yellow kit is only available with white side covers
Add-on Headlight cowling fits S and SM models not "E" offroad model
Comfortable Oversize (or Fat Bar) Handlebars.
For bikes with factory 7/8" handlebars these will require the use of a 7/8 to 1-1/8 adapter (sold separate).
This rotating shift tip provides 6 different positions, offer more sensitive shift position adjustment. Shift arm is made of A2014 forged aluminum for durability and is black anodized. Foldable shift tip is made of CNC aluminum with knurled finish for better shift grip. Replacement shift tips and tip mounts are available.
The Magura Hymec Hydraulic Clutch system. Simply remove the stock perch, lever and cable and bolt this in its place. This system replaces the stock cable with a small lightweight hydraulic system for improved clutch control, easier operating pressure, a constant pressure point and smoother actuation. Developed over many years and tested under the toughest conditions possible in the off-road motorcycle world.
You will have to bypass your clutch safety switch to use this unit.
Never hurts to have a bit of the Margura specific Blood Red hydraulic fluid as well.
You can add this cam buckle loop to any 1" flat webbing system and have an instant secure way to tighten your load.
Available in 6 colors.
CONSTRUCTION FEATURES
This kit fits all Nomadic tubular type racks. (All flat stock racks are already RotoPax compatible)
The second image shows the kit, which includes all the hardware and instructions required. The lower image is just an example of what the eXpander looks like mounted to one of their racks.
Hand built aluminum luggage rack from the B&B Off Road Engineering folks down under. This unit really is a beauty to look at and extremely rugged, made from 4mm 5083 aluminum plate! Tie down whatever you need with confidence. Whether it's your books to get to school or a bag to get across the country, no worries mate. Available in either bare polished aluminum or with a black polymer coating.
While plenty rugged to use as grab handles, you can keep your stock handles if you so desire. All necessary stainless clamps and bolts are provided.
If you want a wider platform for support, consider adding the luggage plate to this rack.
Bike must have the DR250 Taillight installed to work with this rack.It will not work with the stock USA taillight.
If you just installed aftermarket LED turn signals or an LED integrated tail light and your turn signals are flashing way too fast, or perhaps simply staying on completely, you're at the right place to find the solution! The TST Gen2-SK LED Flasher Relay fixes what we call "hyperflash". It slows the flash rate down to a pre-set 85 cycles per minute but can be sped up or slowed down using the adjustment dial located within the unit so you can get the exact speed you are looking for. The plug-and-play installation means that you don't need to splice in any load balancing resistors that generate unnecessary heat and require splicing into your stock wires. Simply remove the stock relay and install your new TST relay and your wiring job is done. It's that simple!
Please make sure your bike uses a 2-pin relay for the signaling system. If your bike has hazard lights it may need the 4-pin relay. Please also note the pin configuration and make sure it matches what is on your bike. It is very important to verify fitment before making your purchase.
The 250 taillight & brake light fits perfectly into the pocket from the stock DR650 taillight on the rear fender. Smaller and much better looking than the original.
Totally 'plug-n-play', includes a standard bulb installed or purchase an LED replacement, sold separate, for even brighter braking. The wire pigtail plugs directly into the DR650 harness just like stock.
Does not fit with the ProCycle Fender
This is a plug & play low profile LED light bar kit which includes laser cut stainless steel mounting brackets and high quality wire taps.
IMPORTANT: Must be used in conjunction with LED headlight or bulb that consumes no more than 35W.
Please note that this product is not compatible with the 1987 TW200.
A nice place to mount auxiliary lights on your KLX where they will be high and easy to reach for adjustment but still tight to the cowlings. They will not interfere with controls, body work or the fuel tank.
Constructed of 1/8" stainless steel they are intended for LED lamps in the 2" range, but with a slight slotting of the mounting holes, will work great with 3" lights as well. Includes longer bolts to for the upper triple clamp mounts.
We worked with TechSpec to have them make custom tank grip pads that look great on both Acerbis (5.3 and 6.6 gal.) and IMS tanks. These pads not only cover those ugly scuffs, but give great knee grip to the slippery plastic.
These have been tested on two of our shop bikes for over 3 years, they did not bubble or peel off in any way.
The WR Speedo is driven by the motor and is inaccurate up to 10% in the stock configuration. Change your gearing and it gets worse. This speedo calibration device is the smallest in the world and has the widest calibration range available. It has a simple plug and play installation that you do have to program, but easily done just using your current gearing. Change your gearing, easy to change your speedometer.
Other beneficial features include:
Protects AC lights from high voltage blowouts in systems with no battery
No Toil rim grease is a high viscosity, non petroleum based compound specially engineered to provide the ultimate filter rim to air box seal.
Designed to withstand temperatures up to 300° F, it remains waterproof and dust-proof, keeping damaging dust and water from being drawn past your filter
This Official 2001-up Yamaha TW200 Trailway Factory Service Manual provides repair, maintenance and service information for 2001-up Yamaha TW200 Trailway motorcycles. Most of the information is useful for the 1987-2000 models as well.
Repair kit for your rear disc brake caliper.
EBC Double H Sintered pads feature the HH friction rating - the highest in the industry.
Provides maximum brake effect and lasts twice as long as organic pads.
All the parts you need to freshen up your brake master cylinder. New piston, seals, return spring, boot and snap ring.
Made by Nissin, an OEM supplier in Japan
The DR650 is rather hard on the cush drive rubbers. Replace these any time you feel excessive play in the sprocket carrier hub. Excessively worn dampers can cause the cush hub bearing to fail - which will ruin your sprocket carrier. Sold as a set of 6 rubber dampers.
Lost your side panel hardware? You aren't the first! We've got replacements. Two side panel screws, two special washers and the rubber insert that protects the side panel from the muffler.
The Complete Doohickey Replacement Kit features the Doohickey supplied by Eagle Manufacturing, a torsion spring accompanied by a drill bit, a generator cover gasket, and an exterior cover gasket. Additionally, it includes all necessary components for rotor removal, along with a replacement bolt for reassembly.
ULTRA HIGH-PERFORMANCE HYPERSPORT TIRE
Avon's technological design and construction gives ultra high-performance handling and stability characteristics.
Multi-compound rear tire for all around performance.
Tubeless and V rated (for max speed of 149 mph)
Pirelli's Corsa radial or bias-ply with maximum grip tread.
Superb corning and straight-line stability.
Exceptional wet-weather performance.
Tubless design.
Light up your work area with this LED Flexible Light with Magnetic Base.
Order up your new levers here! If you keep breaking levers, you might want to think about a set of hand guards to protect them in case of a fall.
A set of three OEM Suzuki front sprocket bolts. Thread-lock compound has already been applied for extra security.
Slime Tube Sealant is formulated and tested for use in all tube tires. Once installed, Slime remains liquid and will not harden or dry out. Slime is guaranteed for 2 years.
As the Slime treated tube rotates, centrifugal force pushes the sealant to the tread area creating a layer of protection, repairing punctures as they occur and treating existing punctures. Slime is not intended for use in tubes losing pressure from sidewall punctures, bead leaks, damaged rims or faulty valves. Slime for tube type tires is not recommended for use in tubeless tires.
Revolutionize your riding experience with Swiftkicker.
An adjustable kickstand for your motorcycle. Swiftkicker is built for offroad motorcycles, dual sports, and dirt bikes. Designed with the idea in mind that motorcycles should be able to take you anywhere, the Swiftkicker motorcycle kickstands help you do just that. You can set the length to anywhere in a six inch range of travel so you can stop anywhere without having to worry about having an even surface to park.
With just a flick of your toe, you can adjust the kickstand to the desired height, park your motorcycle, and be on your way.
No longer will you have to search for a rock or piece of wood to prop your motorcycle up with, or even worse, coming back to your bike to find it has tipped over from unstable ground.
The Swiftkicker is 100% manufactured in the USA from the highest quality components.
The billet 6061 head and the hard anodized tube are significantly stronger than the stock stand. An oversized foot will assure that the end of your stand stays where it belongs, rather than eight inches underground with your bike lying on top of it. The design is trail proven in the harshest possible conditions. Because nothing is indestructible, any of the kickstand components are replaceable at a lower cost than purchasing an OEM kickstand.
Measured from the center of the pivot to the bottom of the foot.
Extra protection for your motor! Strong magnet at the end of the plug picks up ferrous metallic flakes in your oil, protecting your engine!
Replacement friction plates.
Aramid High Performance Clutch Disc Sets use aramid to add strength, reduce wear and increase life of the friction material; aggressive riders will benefit from the superior performance of race-proven aramid.
Limited to stock on hand.
The Moose Tire Bead Tool holds your tire in place as you work you way around the tire
Made of aluminum with a nylon screw so it will not scratch the rim
Sold in pairs
This DR650 Oil Filter Guard is CNC machined from solid 6061 aluminum, black anodized, and then custom laser etched with our logo.
It fits over the fragile OEM magnesium cover and provides great impact protection in the event of a tip over. Proudly made in the USA.
