Our offices will be closed on Friday, July 4 for the Independence Day holiday. We will be back in the office on Monday, July 7.
This type of flasher is required for LED turn signals. For DC (battery) systems only. Includes 2 female connectors for universal fit.
Not compatible with any DRZ400
When upgrading your Suzuki DR650 with LED turn signals, it's required to install a diode module to prevent all of the signals from blinking at once regardless of left or right signal activation. Some riders choose to splice and solder their own solution, but we like things plug and play. That means all you have to do is plug in the TST kit and you're done! There's no need to cut or splice your OEM wiring harness or break out the soldering iron and electrical tape.
Easily turn your blinkers into additional running lights and brake lights (rear) for added visibility.
White light in the front and red in the rear. Rear red running lights and bright red brake lights. You can omit the running and brake lights if you wish and still have the best blinkers on the market.
Dazzling bright Amber blinker functions.
All in a spring-loaded stock to prevent damage from a tip over, crash or impact with brush, trees etc. They will bend 360 degrees, but are stiff, durable and nearly unbreakable.
Kawasaki KLR650 Gen 3 / KLX300 Specific plug and play kit using factory connectors, flasher and block off plates.
Clear lens, amber LED type lights. Short flexible stems. Very small, only 2 7/8" long. Requires a LED turn signal flasher to flash properly. 4 Pack
The Mojave Series LED Racing Lights have been designed to survive and operate in extreme conditions. Lights feature a heavy duty housing that can withstand hard impacts and a lens that is twice as thick as traditional lights. The light includes three different replaceable lens (Flood, Spot, and Combo).
Features:
This kit will work with the 6.6 Gallon Acerbis fuel tank for the DR650. You must run the light brackets inwards in order for there to be proper clearance with the 6.6. Gallon tank.
Kit includes:
This is a plug & play low profile LED light bar kit which includes laser cut stainless steel mounting brackets and high quality wire taps.
IMPORTANT: Must be used in conjunction with LED headlight or bulb that consumes no more than 35W.
Please note that this product is not compatible with the 1987 TW200.
This is the ultimate headlight upgrade for your XT250! It’s a plug & play kit which includes the newly released Morimoto round headlight with preassembled aim adjustable mounting bracket set. Installation takes five minutes and the light output is phenomenal.
Low Beam: 2,400 Lumens, 20 Watts
High Beam: 4,300 Lumens, 35 Watts
Color Temperature: 5,000K
Warranty: 5 Years
Race Tech HP Springs have a high stiffness-to-mass ratio. In other words; the springs are light weight for their particular spring rate. This requires the finest materials and processing. Shot-peened and pre-set so they cannot sack out. All Race Tech HP Springs have the highest rate tolerances in the industry. These are the finest springs in the world-guaranteed.
This spring is 8.0kg/mm
OEM spring rates are 5.7-7.6kg/mm progressive style.
The V-Strom suffers from poor compression damping and limp rebound damping. The Race Tech Gold Valve allows you to tune both compression and rebound valving for vastly improved performance.
Rebound Separator Valves replace the shock shaft nut with an asymmetric valve (provides a different flow rate in each direction of travel) to increase traction and improve bottoming resistance and pitch control.
Why is this needed? On a standard shock the Low Speed Rebound Adjuster flows the same on compression and rebound. In testing, when the lowest speed rebound damping is quick enough to get good traction, the lowest speed compression damping is too mushy. This causes a vague feeling and bottoming on long duration hits like big dips or gullies in Dirt. For Pavement RSV's have the added benefit of pitch control (front to back movement during acceleration and braking). This keeps geometry more consistent.
The Valve has a partially drilled bleed hole in the center. IT MUST BE DRILLED BY THE END USER TO THE PROPER SIZE (2.8mm).
Low friction 'triple lip' seal design. Oil seals last 3-4 times longer that OEM seals. Kit includes Fork Seals and dust wipers.
Includes all components needed to rebuild you forks.
Lowers the rear suspension. Precision machined from billet aluminum and anodized.
Reinforced for added strength/durability when adding weight.
*Important when lowering the rear suspension you want to raise the fork tubes in the clamps an equal amount of inches that the rear is being lowered. That way your bike will sit level when done.
Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.
Complete Pivot Works kit to replace the bearings and seals in the XR650L swingarm pivot.
Convenient kit eliminates looking up many part numbers.
Each kit contains bearings, pins, collars and seals manufactured to OEM specifications for a perfect fit.
The IMS Super Stock pegs are the perfect choice for both the daily commuter and the rider-in-training. Their mellow tooth design keeps you planted while preventing wear on your soles. They are also perfect for young riders who don't need or want a more aggressive option.
Wider foot pegs for sure-footed comfort.
17-4 cast stainless steel.
| Width | 1.97" |
| Length | 3.18" |
Low peg mounts from JNS Engineering. You can use your stock pegs or aftermarket pegs with these T7 mounts.
These offer a 24mm drop & 24mm rearward offset.
Note: Not compatible with any center stand.
This kit combines common wide platform Yamaha YZ/WR foot pegs with brackets that are custom made to fit the TW200. If you are tired of standing on the stock skinny footpegs, get yourself a set of these fat boys and have pegs that match the tires on your T-Dub! For ultimate comfort, order the Pivot Pegz kit!
Simply unbolt your stock brackets and bolt these in their place. The bracket on the right side (brake lever side) is shorter than stock to correct the offset in the stock pegs. On kickstart models, the stroke of the kickstart lever is shortened slightly. Should you ever need to replace the pegs in the future, simply order pegs for the Yamaha YZ or WR 250/450.
The SW-MOTECH center stand for your Yamaha Tenere 700 increases the versatility of your machine for more secure parking on various terrain while enhancing ease of maintenance. Robust steel construction provides sturdy support for the motorcycle and is powder coated black for enhanced durability and corrosion resistance. This high quality center stand is designed and engineered in Germany for seamless integration with the factory original components and easy operation utilizing a built in foot lever which increases leverage and decreases lifting effort.
Features:
The must-have accessory for adventure-touring. Greatly eases basic chain maintenance, tire changes, parking, and bike cleaning. Super-strong steel construction features typical German design and high engineering standards. Superb integration with the factory exhaust and side stand components - retain all existing features without sacrificing lean angle or clearances.
All hardware needed to mount the centerstand included. Typically installs using basic hand tools. No welding, cutting, or drilling of existing frame or body parts required. Tough black powdercoated finish with some gray fittings or hardware as applicable. A double-retention spring is included as a safety feature to prevent the centerstand from contacting pavement if one of the two springs should fail during a ride. Designed to work with OEM components -- we cannot assure fit with aftermarket exhausts or other accessories.
The SW-Motech Centerstand is something that should be an OEM item. Essential for flat tire repairs, tire changes, chain maintenance, oil changes, loading/unloading luggage and many other day-to-day maintenance operations.
Integration with OEM exhaust and sidestand is exceptional. The extended foot lever maximizes leverage making for easy elevation of your Twin. There are no penalties in clearance for these benefits. Tubular steel construction with a heavy-duty black powder coat provides for a stable foundation for supporting your motorcycle. No sacrifices were made to the performance or clearance of the Twin.
Installation is a simple bolt-on procedure; no drilling, cutting, welding or relocating other components for fitment. Package includes all necessary mounting hardware and detailed instructions.
Please Note that the Centerstand works perfectly with the Skid Plate Extension.
The basic purpose of a center stand serves to enhance ownership experience by easily raising the rear wheel completely off the ground for drive chain lubrication and adjusting, tire & tube patching/replacement and even FRONT wheel work. Those fortunate enough to have owned a motorcycle equipped with a center stand have come to learn the game-changing role it can play -even off-road.
Center stands have many more inherent uses including:
Unlike a basic portable moto stand, your center stand is ALWAYS available wherever your need it, whenever you need it.
When in use, this kit raises your rear tire 3/4" off the ground. When retracted, the stand tucks away, 100% unobtrusive to the rider and passenger. A robust retention spring ensures the stand remains retracted, even on the roughest trails.
Each kit comes with all hardware and detailed instructions. All parts are powder coated black with a fine texture
Changing tubes or tires without the right tools can be a real chore. Don't fight your snug beads any longer, use this 27" long tool that opens to 7-3/4" to provide the leverage you need to easily break your tire bead. Constructed from heavy-duty steel with comfortable no-slip grips, this tool makes the job a snap.
No more fighting to keep the bead down while installing or repairing your off-road tires. The Bead Buddy holds the tire bead down in the drop center of the rim during tire changes making changes as easy as possible. Machined from tough 6000 series aluminum the Bead Buddy is light weight and compact enough for any tool pack. The Delrin securing thumb screw insures no scratches to your rims.
The Bead Buddy is NOT recommended for use with Bib Mousse tubes.
A compact and lightweight solution to eliminate the SNAP for a safer tow. If you have ever towed a motorcycle you are familiar with the snap that comes with a traditional tow strap. GCAG made the Dynatow with a section that gives 32 inches of stretch so both riders have an easier tow.
The 26 foot total length gives you enough room to maneuver around obstacles and allows the freedom to choose better lines if you are towing in the gnar.
You can also use this as a recovery strap. You can girth hitch the loop end to the bike and throw the other end to a friend to pull. The dynamic properties of the Dynatow will help assist the pull. All of this functionality fits in a flat pouch about the size of sandwich and only weighs 12.8 oz. Throw it in your bag and be prepared.
Specifications:
Please consider the following before use: Practice before you need to use this product. Always inspect your Dynatow strap before use and NEVER use a worn strap. They recommend a proper training class to learn safe methods for towing a motorcycle.
The Giant Loop Tow Strap is a multi-functional tool that helps get you or your riding friends out of sticky situations.
This Cordura® Ballistic tow strap, designed with sewn loops on each end, can be girth hitched around a tree, bumper, rock, etc.; or used with footpeg-to-footpeg or other motorcycle (and snowmobile, ATV, snow bike) towing techniques. Constructed in the USA from ultra-durable custom woven Cordura® Ballistic webbing, which folds up into a compact integrated cover made with 22 oz. vinyl-coated polyester, or what they like to call “truckers tarp.”
Doubles as a quick deploying, super-strong ridge line for pitching a shelter tarp.
Color may vary based on manufacturer availability, quality will not be compromised.
The GCAG handles are comfortable to pull so whoever is helping will pull harder, and they are soft against your fender so you won't have any annoying bouncing, noise, or graphics damage.
GCAG dirt bike lift strap handles are constructed of 1" thin nylon webbing with flat stainless steel tri-glides for attachment. The grip section is built with 1" climb-spec tubular nylon webbing and a comfort grip handle.
Features:
Warp 9 Supermoto wheels are built with billet hubs, 7000 series aluminum rims and laced and trued with stainless steel spokes and nipples.
The 3.5" x 17" front wheel includes a 320mm brake rotor and caliper relocation bracket.
The 4.25" x 17" rear wheel also comes with a rear brake rotor already mounted.
Add tires to your wheel order and we will throw in tubes and mount and balance them at no additional charge.
Rear wheel Includes Sprocket Carrier with 525 40T Sprocket installed that matches selected hub color.
Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.
Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.
Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.
Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.
Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.
The rubber coated outside diameter creates an optimum seal at the hub.
Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.
| Description | QTY per Kit |
| Ball Bearing | 2 |
| Seal | 2 |
This USB device connects to a battery cable with an SAE connector just like the typical Battery Tender outlet, and allows you to charge your electronic devices. Input is 12 Volts, with an output to the USB port of 2.1A maximum, perfect for your phone or other USB devices.
The Optimate Cable O-20 is a SAE weatherproof bulkhead/panel mount power source. Main body fits a 1" dia. hole. Overall length of the unit is 12" from top of bulkhead to end of connector. Both connectors are industry standard 2-pin SAE connectors. We also offer an optional stainless steel bracket that you can bolt on wherever you like. This makes a clean installation and you won't have a charging cable hanging loose.
Cable max. rating is 10 Amps. Includes an in-line rubber seal at the connector end and a protective cover at the bulkhead for when you don't have something plugged in. Unit has a 3-year limited warranty.
Don't have an SAE plug attached to your battery? Choose the add on below.
Softer return spring for your TM40 carburetor.
This replaces the stock return spring that comes with the TM40 carburetor creating a 25% lighter throttle feel.
Please note that the Power Vision 3 Handlebar Mount is used in conjunction with POD-300 Digital Display
The perfect complement to our Power Commander V or AutoTune modules, the POD-300 gives you an accurate real-time reading of your vehicle’s vital fuel, engine and air information.
Featuring a robust array of options, you can toggle the display, so the data most important to you is front-and-center. The POD-300 can log channels to internal memory, then access them when you’re done riding through our Power Core software (only available for Windows computers). This display module connects to your Power Commander V/6 or Wideband 2 device network through a CAN cable (included).
The POD-300 is weather-resistant, so it can be used in any environment. The high-contrast display is easily viewable in direct sunlight. It includes a velcro backing for easy installation and removal, or you can purchase a handlebar mount separately.
Please note that the POD-300 is a display module only, which is used in conjunction with Power Commander V, Power Commander 6, AutoTune or Wideband 2.
Kit includes:
Not for the stock carburetor Fits FCR-MX conversions Only.
Thick, flat foam, greaseless sealing ring ensures maximum contact with your airbox while acting as a breathable gasket for increased air passage
Features:
Fits all TW200's. Includes a new cap and uses the stock petcock. Capacity is 2.7 gallons (stock tank is 1.8 gallons).
Clarke tanks do not come with a vent hose or vent cap.
Please note: All Clarke TW200 tanks have blemishes due to the mold used in their manufacturing process. Also, side panels are likely not snap into tank as they do on the stock tank.
For those people who have been wishing for a dual petcock setup for their Acerbis 5.3 and 6.6 gallon fuel tanks. Install this kit to get the last bit of fuel from the right hand side of the tank without tipping the bike on its side. Includes the right hand fuel valve, o-ring, screws, tee fitting, fuel hose and spring action hose clamps. You will have to drill the hole in your tank for the petcock standpipe. For Acerbis tanks only.
This gasket seals the joint between the head pipe and muffler. These gaskets are easily damaged when removing the original muffler. Get a fresh one now to ease installation of your new performance muffler.
This gasket seals the joint between the head pipe and Exhaust port. These gaskets are designed to crush a little bit to tightly seal where the pipe fits to the head. Get a fresh set now avoid having an exhaust leak when you install your new exhaust. This is for a set of two gaskets.
The V2 Slip-On features new aluminum end caps. A USFS Spark Arrestor. DG offers 4 different Quiet Core Inserts to reduce exhaust sound. Lightweight at approximately 5.5 lb.s
The Side Bag Hauler Kit has been designed to work with or without the GCAG Uprising Soft Rack. These straps allow you to use standard dry bags for side luggage. When installed properly you will be able to thrash about offroad and your luggage will stay put! With this setup it is very important to strap your bag in tightly and double check your exhaust clearance.
Bags can be rigged horizontally or vertically.
Hard luggage can increase your risk of injury, especially on offroad terrain. With this system you can reduce your potential of injury and have adaptable, waterproof luggage.
Kit Includes:
With 3.5-liters of packable volume, the super-rugged, universal roll-top Possibles Pouch™ provides enough capacity to carry a set of tire irons, spare tube, compressor, tools, and other small offroad essentials. The bag also allows one to add external pockets to Giant Loop’s MoJavi Saddlebag, Coyote Saddlebag, Great Basin Saddlebag, and MotoTrekk Panniers.
The Possibles Pouch gear pocket is 100% waterproof, dustproof, and mudproof. It can be anchored to engine guards, crash bars, tail racks, or any other secure attachment point on virtually any motorcycle make or model. Add Giant Loop’s bolt-on Tail Rack for an instant trail riding solution that gets the weight off your body and onto the bike for improved performance and less fatigue.
Features:
The Nomadic Rack is a favorite for dual-sport riders with ruggedness and ease of installation. This rack does not need to be removed for under-seat maintenance. The mounting area is large 11" x 10" and the rack weighs just under 3 lbs. It constructed of 16 ga. steel and fully welded, then powder-coated black with a shot-peened look. Has a rigid four point mounting system and doubles as a grab handle. Complete instructions and stainless steel hardware are included.
The universal E-series adapter plate is designed to add a Givi Monokey topcase to most existing flat rear luggage racks. All necessary mounting hardware and installation diagram for attachment to generic tubular-steel flat rear luggage racks is included. This is a universal plate so making it work on your tail rack might need a little self engineering.
Typically installs quickly using simple hand tools. Mounts standard Givi Monokey topcases (ie E45 Elegant, E460 Delux, E52 Maxia), or the flat, stable surface can be used as a solid toprack when the topcase is not needed. Not for use with GIVI Monolock topcases. Made of durable molded nylon with a rugged black finish.
What's in the Box:
The 2023-2024 Honda XR150L skid plate protects your bike no matter the terrain. The XR150L skid plates are made from high quality aluminum and offer full coverage. It comes with unique, proprietary hardware that requires no drilling and tapping into your dirt bike. Comes standard with a clear anodize for extra protection. Buy your skid from the industry's longest-running skid plate manufacturer. Ensure your Honda stays safeguarded in style—made durable in the USA.
bash plate is made from 4mm aluminium 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider.
All bash plates are supplied with the necessary stainless clamps and bolts where possible. All bash plates have a polished finish and have foam or rubber where required.
These hand-crafted bash plates from B&B Eng. are constructed from 4mm 5083 aluminium plate. Strong and lightweight, this material has been selected because of its extreme suitability for welding, abrasion and impact resistance. All the necessary stainless clamps and bolts are included. Plate has a polished finish with foam or rubber where required.
This is a high-quality seat cover offered by Moose for the DR650. This is a replacement cover only, no seat foam and you must install on your existing pan with existing foam. Strong marine-grade vinyl that's made to last. UV protected from sunlight for extended use and has double stitching for extra strength.
Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!
Our casual t-shirt with a classic ProCycle Logo on the front and a topo map of our favorite local riding spot on the back. High quality soft t-shirt perfect for everyday wear.
T-Shirt Specs:
From Barnett, the number one name in motorcycle clutches since 1948, we now offer a complete high performance clutch set. This includes Kevlar friction plates, steel drive plates and stronger springs.
The Rekluse EXP employs the same EXP assembly as their premier product; the difference is that it fits into your stock clutch assembly, saving you money! Now you can enjoy the benefits of Rekluse auto-clutch technology on your KLR.
An auto-clutch automatically feeds out the engagement of the clutch using centrifugal force. This allows you to start and stop without touching the clutch lever. The automatic feed is fully adjustable to suit the rider's needs while retaining full manual override with the clutch lever. This automatic feed delivers easier on/off throttle transitions, improved traction, better control, and more confidence.
Complete set of friction plates, HD springs and steel separator plates prevent premature driven plate wear, oil muddying and loss of stack height. Built with swaged aluminum carriers that spread the load on the clutch basket and prevent clutch basket "dogging". Anti-swell, alloy impregnated heavy-duty facings for smooth clutch action. Allows modulation, unlike paper clutches which tend to snatch. Don't forget to add a fresh gasket.
Generator cover gasket to seal up the cover once you have your new Doohickey in place. New OEM gasket. What else can we say? If in doubt, put in a new one.
Adjusting your valves or setting your cam chain tension? Here are the O-Rings that fit in the TDC sight plug and the crankshaft nut access plug.
Complete set of engine gaskets with oil seals.
This is all you need to not only change your oil, but protect your motor as well. We include a magnetic drain plug in the standard kit, to help catch stray metal pieces, a 5-pack of oil filters, and new O-Rings to replace any you have that may be leaking or worn.
Standard kit includes:
285cc big bore kit includes:
Wiseco piston 78.00/+5.00 10.5:1 (with rings, pin & clips):
HotCams stage 1 camshaft:
Complete top end gasket set:
This is a great combination and a big 'bang for the buck' performance increase.
No re-sleeving required. You will have to have your cylinder bored to fit the larger piston.
These are the first batteries with built-in jump starting. They intelligently monitor their status, and just before going completely dead, puts itself to sleep with just enough energy to get your vehicle started again. Simply press the RE-START button located on the battery, start your bike and ride away.
These are an extremely lightweight (2.5 lbs.) high-powered Lithium-Ion replacement battery for motorcycles. These batteries offer the first Battery Management System (BMS) found on a powersport battery and includes low-voltage cut-off, over discharge, over-charge, and thermal protections with real time lithium-ion cell balancing. Use of a lithium specific charger to maintain the life of the battery is highly recommended.
Product Size is 8.4"L x 5"W x 2.2"H. If you need spacers, select the optional Foam Kit to pad the battery in the battery box.
Built with the latest in Lithium Ion Polymer Technology. All components are designed, manufactured, assembled and packed in one location assuring high quality and consistency. Besides it's extreme lightweight (50% to 70% lighter than standard lead-acid batteries) it also features a built-in LED test gauge and the ability to mount it in any position. There is no hazardous acid or heavy metals and it is non-explosive and non-combustible.
The Firepower features Increased cranking amps over lead acid batteries and has a very fast recharge cycle and can be brought up to a 90% charge within 6 minutes and also has 6 to 12 times more cycle life when compared to lead acid batteries. A 2-year warranty insures that your investment is protected.
145 CCA 12V/28.8WH
Package Dimensions: 4.75" x 3.00" x 4.50
Built with the latest in Lithium Ion Polymer Technology. All components are designed, manufactured, assembled and packed in one location assuring high quality and consistency. Besides extreme lightweight (50% to 70% lighter than standard lead-acid batteries) it also features a built-in LED test gauge and the ability to mount it in any position. There is no hazardous acid or heavy metals, it is non-explosive and non-combustible.
The Firepower features Increased cranking amps over lead acid batteries and has a very fast recharge cycle and can be brought up to a 90% charge within 6 minutes and also has 6 to 12 times more cycle life when compared to lead acid batteries. A 2-year warranty insures that your investment is protected.
Rated at 250 CCA (Cold Cranking Amps)
Package Dimensions: 6.20 x 3.70 x 4.80
Built with the latest in Lithium Ion Polymer Technology. All components are designed, manufactured, assembled and packed in one location assuring high quality and consistency. Besides extreme lightweight (50% to 70% lighter than standard lead-acid batteries) it also features a built-in LED test gauge and the ability to mount it in any position.
The Firepower features increased cranking amps over lead acid batteries and has a very fast recharge cycle, and can be brought up to a 90% charge within 6 minutes. It also has 6 to 12 times more cycle life when compared to lead acid batteries. A 2-year warranty insures that your investment is protected.
220 CCA 12V/48WH
Package Dimensions: 6.20 x 3.70 x 5.25
Built with the latest in Lithium Ion Polymer Technology. All components are designed, manufactured, assembled and packed in one location assuring high quality and consistency. Besides extreme lightweight (50% to 70% lighter than standard lead-acid batteries) it also features a built-in LED test gauge and the ability to mount it in any position.
The Firepower features increased cranking amps over lead acid batteries and has a very fast recharge cycle, and can be brought up to a 90% charge within 6 minutes. It also has 6 to 12 times more cycle life when compared to lead acid batteries. A 2-year warranty insures that your investment is protected.
165 CCA 12V/36WH
Package Dimensions: 6.20 x 3.70 x 4.45
Built with the latest in Lithium Ion Polymer Technology. All components are designed, manufactured, assembled and packed in one location assuring high quality and consistency. Besides extreme lightweight (50% to 70% lighter than standard lead-acid batteries) it also features a built-in LED test gauge and the ability to mount it in any position. There is no hazardous acid or heavy metals, it is non-explosive and non-combustible.
The Firepower features Increased cranking amps over lead acid batteries and has a very fast recharge cycle and can be brought up to a 90% charge within 6 minutes and also has 6 to 12 times more cycle life when compared to lead acid batteries. A 2-year warranty insures that your investment is protected.
220 CCA 12V/48WH
Package Dimensions: 5.60 x 3.25 x 6.38
Direct replacement cables for your T-Dub. OEM or high-quality replacements will keep you on the road or trail. Pay attention to the model year for correct fitment, then select the cable type: Throttle, Clutch or Speedo, they're all here.
Folding tip, forged aluminum shift lever from BBR Motorsports. Stronger and lighter than the stock shift lever.
Quality replacement levers. Standard length.
Aero Tapered Aluminum (ATA) Oversize (or Fat Bar) Handlebar.
For bikes with factory 7/8" handlebars these will require the use of a 7/8 to 1-1/8 adapter (sold separate).
Here is a complete kit to install oversized tapered 1-1/8" handlebars on your DR650. Warp9 handlebar clamps bolt to your stock triple clamp adding an additional 1" to the height.
Alloy oversize bars offer more durability and eliminate the crossbar which opens up your dash area for more goodies. Black in color.
This is the brace needed to stabilize the big front fender on the XR650L. This simple bolt-on brace reduces wind buffeting at highway speeds. It also helps carry the weight of a fender mounted tool bag.
Made from laser cut 5052 aluminum, then CNC formed and beautified with a shiny black powder coat. Easily mounts in a few minutes using the included hardware.
Finally! Quality replacement body parts at a fraction (35%!) of the OEM parts. Polisport's parts have been developed with their exclusive technologies - IPD (In-mold Plastic Decals) and DGP (Durable Gloss Propylene). These processes make these parts even more resistant and durable than the stock units with a perfect fit and glossy finish. The Side Panels include heat protection film, washers and rubber grommets, just like the OEM parts.
You can purchase individual parts, or a discounted complete kit. If your taillight unit was damaged with your rear fender, we offer a brand new OEM unit as an optional add on.
A 5-pack of easy to use disposable funnels to help make any oil or fluid change cleaner and more precise.
Thread Chasers are designed to clean and re-cut damaged aluminum threads.
This kit contains the two sizes most common on metric motorcycles, M6x1.0 and M8x1.25.
Thread Chasers also remove dirt and metal shavings that become captured in thread grooves.
Uses 8mm or 10mm hex sockets, a Must for all tool kits.
JT Sprockets is the world's leading manufacturer of aftermarket sprockets, constantly raising the industry's standards for quality and service. JT Sprockets are the only sprocket manufacturer using the ultra-durable high carbon C49 steel for rear sprockets.
Ideal for smaller street bikes or smaller SuperMoto wheels.
Offers safety, durability with a ratio of grooves that has been increased to improve the balance between grip and wear.
Grooves run from the center to the shoulder to facilitate the evacuation of water and offer good grip on wet roads.
Possibly the best value for smaller SuperMoto tires.
Bias-ply and tubeless, S rated (max speed of 112)
EBC brake pads contain aramid fibers; these are man-made high-performance fibers used widely for their light weight, high strength, abrasion resistance and thermal stability.
Sintered Pads:
Each kit includes all necessary rubber components and brake pins.
A fresh set of brake rotor bolts.
Genuine Yamaha OEM bolts work with factory and aftermarket rotors.
Comes in a pack of 6.
The Phillips type screws used in Japanese motorcycles are actually Japanese Industrial Standard (JIS) screws and are easy to strip if you are using a regular Phillips screwdriver.
Here is a little kit that will make removing and replacing JIS screws much easier. Includes 2 each of JIS No. 1, No. 2 and No. 3 bits.
These will work in other bit holders and have a mild magnetic tip.
Features:
Features:
Innovative design makes tool easier and more secure to use than old fashioned pin-aligned drivers
Innovative design makes tool easier and more secure to use than old fashioned pin-aligned drivers
This high quality socket from Motion Pro, is specifically designed to reach into the very small, deep space where the spark plug of the XR hides.
Normal sockets simply won't work in this case.
This brake bleeder makes bleeding your brakes a one man job.
The unique check valve allows fluid and air to escape while preventing air from re-entering the system.
This Motion Pro press tool is a must have when installing and removing Clip-Style master links (520, 525 & 530 sizes).
Easily presses on and off master link plates, works on 520, 525 & 530 Clip-Style master links.
Maximum master link width 24.8mm.
Will not damage master links, hardened steel pins for reliable use.
Light weight billet aluminum construction.
This kit is for those of you looking for a bit more leg and arm room in the DR cockpit. Included are ProCycle Low Foot Pegs and our oversize bars.
Have your tank cushions worn out over the years? Have you lost one or more while working on your bike? We have new upper and lower tank cushion rubbers.
This kit includes the original hardware, upper, and lower cushions.
