Quality replacement radiator air scoops. Sold in pairs for gen 1 KLR650.
Available in 4 colors.
New replacement side panels specifically made for gen 1 KLR650.
Available in 4 colors.
Will not fit KLR250
Depending on your application and preferences, more than one optional heat shield may be useful.
Replacement front fender by Maier that will fit great on your TW200.
Note: The proper way to install this front is to install the stock fender bracket to the under side of new Maier front fender using stock screws and nuts.
Formerly DSA, now ProCycle brand, is a plastics kit in three colors - Black, White, and Blue, as well as Blue fenders with White side panels and Black fenders with White side panels. (headlight cowl not included).
Vacuum molded, these parts are a design improvement over the stock pieces. The side panels have a crisper, more angular look than the stock parts while the front fender is shaped like the DRZ400SM OEM front fender. Big enough to be functional without wind-steering the bike like the stock fender does.
Kits include front and rear fenders, a new LED tail/brake light and license plate holder, and both side panels.
Add a fresh new side panel hardware kit and an adhesive heat shield for a fresh off the showroom floor look.
Add a Maier Mfg. headlight cowl if you are doing a complete color change to your DR (must select plastic kit with head light cowl option)
GBrakes Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
GBrakes Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
GBrakes Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
New from Warp 9, a full floating 320mm Supermoto disc with caliper relocation bracket! These rotors have an additional hole for placement of a magnet for an electronic type speedo like the Vapor.
Includes a fresh set of brake rotor bolts.
A super compact shovel with several bonus features!
Innovative anchor knot attachment system with an anti-slip cam buckle system that allows you to install or uninstall the bag quickly. Quick-release mounting system with adjustable hook-and-loop straps and an under-seat center strap.
The glove box for your motorcycle! The Zigzag handlebar bag is their smallest bag yet also one of their most popular. Sometimes you only need the basics like your wallet, phone, registration, and other small items, and no matter what you’re riding, the Zigzag handlebar bag delivers quick and easy access to the basics.
Every backcountry adventure-seeker needs a handful of these multi-purpose straps with virtually unbreakable fasteners. Each pair of stretch polyurethane Pronghorn Straps™ feature stamped aluminum buckles sheathed for scratch protection with arrows that line up for easy fastening. Each buckle prong holds the strap in place for pre-fitting and easy chaining of straps together.
Available in color-coded 18-, 25- and 32-inch lengths and marked by size, you’ll find a million uses for Pronghorn Straps—motorcycle, sled, snow bike, 4×4, ATV, UTV/SXS—and so much more!
Not only are Pro Moto Billet Cargo Racks brutishly strong and functional, but they look great too. Each cargo rack is methodically engineered, then CNC machined on-site from a 1/2 inch thick plate of USA made 6061 aluminum by master machinists.
The cargo racks are then hard clear anodized for durability. PMB uses only stainless steel fasteners for worry-free years of riding. Excellent instructions and all necessary har
Need to mount your turn signals to your new Pro Moto Billet Rack? Just add a set of CNC machined aluminum Turn Signal Brackets and that will be no problem. See bottom image.
Note: Placement of this top rack does require removal of the stock tool bag.
Our Tool Tube mounts in place of the little stock tool carrier. The tube is made from 3 1/2" O.D. ABS pipe. It's held by 3 strong powder coated steel straps. Both ends are sealed with waterproof expanding plugs. This is the ideal way to carry those items you always want to have with you on every ride. Tube is approximately 13" long.
You can now order your Tool Tube with a Locking End cap, mini padlock and keys included, on the exposed end.
If you already have a Tool Tube you can order just the Locking End Cap and lock.
The Barkbuster LED Indicator Lights for Jet, Storm & VPS Plastic Handguards to increase your visibility and safety using 15 high intensity LEDs that mount directly to the plastic handguard shells. Super bright auxiliary signals will make your directional intentions clear to upcoming traffic. The LED indicators are very low draw and E marked for road use.
Features:
What's in the box:
Please Note: Not compatible with the electrical system on the Honda Africa Twin CRF1000L
Clear lens, amber LED type lights. Short flexible stems. Very small, only 2 7/8" long. Requires a LED turn signal flasher to flash properly. 4 Pack
These Sequential Turn Signals are available in a 2 pack or 4 pack short stem with 7 LEDs.
Matte Black, plastic body with smoke lens and 8mm mount bolt.
Specifications
Reproductions of the original DR650 factory turn signals. Save a bundle compared to the $70+ each cost of the OEM signals. The wire pigtails plug directly into the factory harness. No cutting or splicing necessary. Choose original style amber lens or clear lens with amber bulb.
This heavy duty aluminum bracket is specifically designed for mounting auxiliary LED lights to the front of your XR650L without interfering with your large aftermarket fuel tank. If your bike needs improved lighting this mount is the best place to start!
– 0.190″ 5052 Aluminum
– Laser cut
– CNC formed
– Powder coated black
– Includes stainless mounting hardware and JNS stickers.
LED auxiliary lights are sold separate.
T700 TENERE Bash plate was designed to withstand the harshest Aussie conditions. Bash plate is made from 5mm structural thick alloy plate and designed for maximum protection with minimum bulk.
Easy to mount and remove. Also includes a replaceable polyethylene linkage guard.
Fits EURO 4 only
Enjoy maximum protection and durability with an SW-MOTECH skid plate. Fully welded aluminum construction is engineered in Germany to provide proper protection from impacts, abrasions and projectile debris. Multiple ventilation slots on the front, sides and bottom of the skid plate permit maximum air-flow to keep your motor cool. Drilling, cutting, welding or any other permanent modifications are not required.
Features:
What's in the box:
The X-Factory Handguards from Acerbis are designed with a steel bar encased in an injection-molded Nylon composite. A replaceable dual-injected polypropylene shield attaches to the bar, providing excellent protection against debris and harsh conditions.
Included with the handguards is a universal mount kit, enabling installation on either 7/8" or 1 1/8" handlebars.
Will not fit XT250 with stock handlebars (oversize bars ok). Recommend Acerbis Rally Pro X-Strong to clear master cylinder.
The SW-MOTECH Rear Brake Master Cylinder Guard is designed to fit the Yamaha Tenere 700. This guard protects the rear master cylinder from impact and prevents the foot from contact. A laser-cut and precision bent aluminum strengthening process makes the construction tough and durable and capable of withstanding heavier blows.
Features:
Radiator guards from Devol Racing protect your radiators from damage due to trail side objects and roost bullets. They offer protection not just from frontal assaults but also from those tricky side attacks. Made from high-grade aluminum alloy for light weight and strength, these guards have an improved air-flow design that eliminates any overheating problem. A solid mounting to the frame make these stronger than most guards that just mount to the radiators themselves.
Devol Racing makes a super product that will keep you on the trail for a long time.
In the shop or on a trip, these are the Tire Irons to have.
Sold Each
No more fighting to keep the bead down while installing or repairing your off-road tires. The Bead Buddy holds the tire bead down in the drop center of the rim during tire changes making changes as easy as possible. Machined from tough 6000 series aluminum the Bead Buddy is light weight and compact enough for any tool pack. The Delrin securing thumb screw insures no scratches to your rims.
The Bead Buddy is NOT recommended for use with Bib Mousse tubes.
Shinko 700 Series tire features an aggressive 60% on-road and 40% off-road read pattern for good dirt riding performance, without sacrificing pavement grip. Other features:
From Shinko Tires, the 705 Series are DOT approved Dual Sport tires designed for 75% street and 25% trail riding. A versatile tread pattern provides excellent wet and dry weather adhesion and the compound resists tearing while riding off-road. "R" in size denotes a radial tire.
Ideal for smaller street bikes or smaller SuperMoto wheels.
Offers safety, durability with a ratio of grooves that has been increased to improve the balance between grip and wear.
Grooves run from the center to the shoulder to facilitate the evacuation of water and offer good grip on wet roads.
Possibly the best value for smaller SuperMoto tires.
Bias-ply and tubeless, S rated (max speed of 112)
DG Performance exhausts help your engine breathe better, resulting in increased throttle response, power and torque.
The V2 Series Slip-On muffler features:
Standard sound level is approximately 98 db and quiet core inserts are available separately.
This Lightweight Slip-On weighs approximately 5.5 lbs and bolts directly to the stock headpipe.
It is equipped with a US Forest Service-approved spark arrestor.
The RS-2 is a potent and versatile design that evolved from their original TRC, engineered to provide increased power delivery. With a different pyramidal shape that features increased volume, the RS-2 is a quieter system with a larger core — and it offers the added bonus of outstanding performance in a value-priced package.
We recommend Anti-Seize on exhaust fasteners
Enhance your DR650's performance with the SS3 Exhaust Muffler, designed for a perfect fit and unmatched quality. This muffler, featuring a round straight shape and a sleek silver color, is crafted from durable stainless steel, ensuring longevity and resistance to wear. With a quiet 86 dB output, it maintains a stealthy presence and never needs repacking, offering a hassle-free riding experience. Proudly made in the USA, the SS3 includes a spark arrester. In addition to the quiet dB rating, the end cap directs the sound waves toward the ground where they are reflected upwards and dissipated.
Note: No muffler joint gasket is required with this muffler.
The DG RST (Reduced Sound Technology) muffler is the quietest DG muffler and is designed especially for dual-sport machines (Just 89db @ 3200 RPM). A new baffle design dissipates sound waves reducing noise output in a very efficient manner. This new design also stretches out the time between muffler repacks. Included is a Stainless Steel mid-pipe, USFS Approved Spark Arrestor and a new Aluminum end cap.
You may want to consider a new exhaust gasket that goes between the header and the muffler.
Reduce exhaust leaks with this new OEM muffler gasket. This gasket goes between the rear tail/muffler pipe and the header pipe.
Race, RS-4, Slip-On, Stainless Steel with Carbon Fiber End Cap
The race-bred RS-2 exhaust has proven to be extremely popular among rider looks for a combination of performance and value. It enhances performance dramatically, provides an enviable exhaust note and offers the unmistakable look and sound of Yoshimura. RS-2 mufflers feature a straight baffle that leads to a single turn-down machined aluminum end cap.
All models have a USFS Approved spark arrester in a oval-shaped sleeve with a large volume of packing material.
Did you snap a headpipe bolt on your XRL or are your headpipe bolts looking a bit dingy and rusty?
These replacement header exhaust stud bolts are made of super corrosion resistant 316 stainless steel. They provide excellent resistance to chemicals and saltwater to give your exhaust system a hassle free service life.
If you've got an older XR650L, you know the struggle of removing the O.E. nuts from the studs. They either snap, remove the stud or come off as they should. At some point you're likely to snap on or come across a seized nut to stud. These bolts are a superior upgrade to the O.E. nut and stud.
Kit includes: 4 Stainless Steel bolts
Is the cylinder head intake boot on your DR650 cracked or weathered, is it missing parts of the lip to seal around the carburetor, have you recently pulled the intake boot off only to realize the O-ring behind it is hard & brittle? This kit is your solution to solving some of those mystery problems and make your bike like new again. There can be a great deal of heat that can radiate behind the cylinder head on a DR650 as it is an air cooled engine. With that comes long term maintenance items that will need to be replaced due to them being made of materials that cannot withstand those constant heat cycles indefinitely.
Our kit includes O.E. parts from Suzuki to include:
Twin Air Filter's patented design, high quality materials and superior construction deliver unbeatable performance and protection - and make Twin Air Filters the hands-down choice of more World and National Champions than all other filters combined.
An air filter is your engine's only protection against the elements, and your stock filter isn't up to the task. Replace it with a Twin Air- the number 1 filter system proven on motocross tracks around the world.
Twin Air's fused layers of open-pore foam and fine inner foam trap even the smallest particles-without restricting airflow
A complete kit to rebuild and refresh your stock carburetor. Kit contains Genuine Mikuni replacement parts.
**Due to varying model requirements, this kit does not include main or pilot jets.
Included in this kit are the parts needed to repair a second generation TK carburetor. You get a new float bowl gasket, needle valve with O-ring, needle, mixture screw, and stock jets for the '01-'26 models kits.
This is an O.E. replacement diaphragm for your BST40 carburetor.
Geared for the do-it-yourselfer that already has a TM40 or HS40. This kit supplies everything you need to convert it for use on your bike.
Kit includes intake and air boot adapters, throttle cables, choke knob, accelerator pump nozzle, a wide selection of main and pilot jets plus a TM40 tuning manual.
More range at a great price.
The 3.6 gallon tank is for the off-road DRZ400 and DRZ400E.
The 3.9 gallon tank for the dual-sport DRZ400S. The 3.9 gal tank also fits the ES and SM models.
Both tanks are available in a selection of colors.
NOTE: Clarke tanks do not come with a vent hose or vent cap.
Get better range from your XR650L by adding a Clarke 4.7 gallon fuel tank. Cannot use stock shrouds.
Available in Natural, White, Black, and Red. Natural color is recommended if you wish to easily see the fuel level in the tank. Includes cap, uses stock petcock.
Get better range from your DR650 by adding an IMS 4.9 gallon fuel tank. Available in Natural, White, Black and Blue. Natural color is recommended if you wish to easily see the fuel level in the tank. Includes cap and fuel petcock.
You want a lighter replacement for your heavy steel stock tank? Don't need the extended range (or bulk) of the big Acerbis or Clarke tank? The 4.0 gallon tank from IMS might be just right. Includes cap, uses stock petcock.
We've been asking for a bigger tank for years and it's finally happened. This is the big brother to the very popular 5.3 gallon Acerbis tank with some modifications to add another gallon and a half of capacity. It's the same width between the knees but extends wider and further forward in front of the knee pockets. This high capacity fuel tank incorporates modern lines and high quality construction that can't be beat. Includes gas cap, petcock and all mounting hardware.
Installation of the Acerbis tank requires relocation of the front turn signals, otherwise the stock signals will contact the tank at full lock. Our Turn Signal Relocation Brackets move the front turn signals up and forward to clear the bigger tank.
The new 4.1 gallon fuel tank from Clarke. Carries almost 2 more gallons than the stock tank. Available in Blue, Black, Silver, White or Natural
You want a lighter replacement for your heavy steel stock tank? Don't need the extended range (or bulk) of a big tank? The 3.7 gallon tank from Clarke might be just right. It's almost 5 lbs lighter and holds close to 1/2 gallon more fuel than stock to increase your range by about 20 miles. Fits with your stock petcock, Pingel or Raptor petcock.
If you're like us, you hate the long floppy vent hose hanging off the cap of your aftermarket tank.
This one-way vent cap replaces the long hose with a short one only about 2" long. It allows air into your tank but prevents fuel from sloshing out.
Machined from billet alloy and anodized for good looks.
Not for stock fuel tanks!
If you need a replacement cap for your Acerbis tank, why not go bling? These caps have a carbon fiber pattern molded into them that is extremely realistic. Looks like the real thing. Topping off the cap is a CNC Machined metal vent cap. This eliminates the need for a lengthy vent tube that gets in the way. The vent cap allows air to vent into the tank but does not allow fuel to splash out during normal use or during a tip over.
These caps fit Acerbis tanks only.
Now you can have minimum output shaft wear, minimum chain drive wear with the FRITZCO DRIVELINE sprocket. The design of their sprockets provide correct chain alignment, allows for full spline contact with the XR650L's output shaft, fit the counter shaft either way, and straight up no hassle installation with the OEM two bolt retainer and fasteners (except 13 tooth that comes with it's own quick change retainer). Their sprockets are machined from alloy steel that is comparable in every way to OEM Honda and the best offered by other manufactures. The sprockets are then given a heat treatment that provides a compatible sprocket for the Honda output shaft and longest wear life possible.
A way to double the sprockets life would be to have a sprocket that fits on the shaft either way so both sides of the teeth can be used. Bear in mind you can't wear one side of the teeth all the way through, then flip the sprocket, and expect double life. You must reverse when a normal wear pattern develops.
16 tooth sprocket is the biggest front sprocket that will run with the standard 110 link chain and 45 tooth rear sprocket on an XR650L
The OEM cover will require modifying to use the 16 tooth sprocket on your XR650L.
JT steel rear sprockets are manufactured using only the finest grade of C49 high carbon steel.
Two styles of rear sprocket were used on the DR350. The 90-95 'S' and 'SE' (street legal) models have a cush drive hub. The 96-99 'S' and 'SE' as well as all of the 'dirt only' models have a non-cush rear hub. Select your sprocket accordingly. If you are not sure, look at your bike. If the sprocket is bolted directly to the wheel hub you have a non-cush model. If your sprocket is bolted to a separate sprocket carrier you have a cush drive model.
High quality steel rear sprockets from 39 to 53 teeth.
Sprocket color may differ depending on size.
Quality Steel Rear Sprocket.
Color may vary based on manufacturer availability, quality will not be compromised.
Not for '17 - '20 KLX140G models
We recommend using the Rear Sprocket Bolt Kit when installing most aftermarket sprockets on your TW.
High quality steel sprockets.
Stock Gearing: 15/48-128x128
Color may vary based on manufacturer availability, quality will not be compromised.
Complete chain and sprocket replacement packages.
This kit provides much of the performance gain of the more expensive 150 (143cc) kits. But gives better reliability due to the thicker wall of the cylinder sleeve.
Replace your worn clutch plates and springs to reduce fade and slip.
Heavy-duty springs help prevent clutch slip in high-performance motors.
Complete set of friction plates, HD springs and steel separator plates prevent premature driven plate wear, oil muddying and loss of stack height. Built with swaged aluminum carriers that spread the load on the clutch basket and prevent clutch basket "dogging". Anti-swell, alloy impregnated heavy-duty cork-based facings for smooth clutch take-up. Allows modulation, unlike paper clutches which tend to snatch.
The complete Thermo Control package - Our in-house designed Thermostat Bypass kit, a set of Custom Silicone Hoses and a Hi-Pressure Radiator Cap. All combined to help your KLR cooling system be at the top of its game. The Thermostat Bypass kit includes a thermostat with a higher temperature rating that will keep the motor more in its happy spot.
The Silicone hoses are stronger than the stock rubber units and will better resist cracking and leaking.
This kit provides much of the performance gain of our 130 kit but keeps you legal for racing classes that do not allow motors over 125cc.
Higher pressure in the cooling system, raises the coolant boiling point and increases protection from coolant loss due to overheating.
23 PSI - 1.6 Bar.
The PSR Oil Filler Caps are CNC machined from high quality aluminum and come with an E-clip that is already safety wired to a mounting tab. The wire is covered with silicone tubing that will not melt or discolor. Available in silver, black and gun metal.
Providing unbeatable performance and exceptional value, Hi-Flo Filter is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide. The filters are also supplied to original equipment manufacturers as well as private label brands.
Grab our 5-pack and save both time and money!
These tips are for the Warp 9 Shift Levers only.
These are held to the cast Warp 9 lever with a pin and e-clip making them easy to change out. Includes new pin and e-clip in case you lose yours.
You can also order just a new pin hardware kit which comes with new pin and clip.
A set of replacement brake and clutch levers. Standard length.
Replacement shift lever with folding tip.
A set of replacement brake and clutch levers. Standard length.
Please be sure and order the correct levers for your model year KLR.
Note: Gen 1 levers are black
Gen 2 levers are Silver
Quality replacement clutch cable.
The Optimate Cable O-20 is a SAE weatherproof bulkhead/panel mount power source. Main body fits a 1" dia. hole. Overall length of the unit is 12" from top of bulkhead to end of connector. Both connectors are industry standard 2-pin SAE connectors. We also offer an optional stainless steel bracket that you can bolt on wherever you like. This makes a clean installation and you won't have a charging cable hanging loose.
Cable max. rating is 10 Amps. Includes an in-line rubber seal at the connector end and a protective cover at the bulkhead for when you don't have something plugged in. Unit has a 3-year limited warranty.
Don't have an SAE plug attached to your battery? Choose the add on below.
Aluminum alloy lowering link. Lowers the rear suspension approximately 1 inch.
Bearings included.
Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.
The Pro-Series is the suspension performance pinnacle. Cogent takes Mojave’s best-in-class performance and adds an external reservoir.
The Pro-Series’ sophisticated reservoir with interchangeable valves and shims, provides more tune-ability at all speeds. It also improves internal pressure balance and temperature dissipation, giving long lasting performance regardless of the punishment you put it through.
Comes standard with the CNC machined Bling Ring Preload Adjuster Collar and a thrust bearing between the adjuster ring and the spring making preload adjustments easy.
The optional Hydraulic Preload Adjuster makes it even easier to adjust the preload. Just twist the knob. Includes mounting bracket for knob unit. (See last image) (Some CA carb compliant models may need slight modification for mounting the preload adjuster.)
Select the spring you want installed based on the load you plan to carry. *Spring color may vary due to specification requirement and availability.
For riders (and gear) less than 250 pounds we recommend the 7.6 kg/mm spring.
If you regularly have more than 250 pounds on the bike, you might want to use the 8.15 kg/mm spring.
Low shock also available. This option will lower your seat height 1" without the need for lowering links. All other features of this shock are the same as the stock height.
Cogent Dynamics Mojave product is a drop-in replacement for the DR650 stock shock, no modifications necessary. Mojave is not simply an improved Suzuki shock, it is a brand new replacement shock that is a totally engineered suspension solution to suit your needs.
Each shock is assembled and tested on the Cogent Dynamics suspension dyno before being packed up and shipped. Like its bigger brother the Mojave Pro Series, this will make an incredible difference in the handling of your DR.
Mojave Improvements over stock
Mojave upper mount: uses a precision spherical bearing with dust seals, which accurately transfers damping forces to the motorcycle frame.
Internal improvements: Cogent designed shaft, seal head, damper piston, adjuster and clevis.
Mono tube construction: precision honed, super-stiff steel body with an upper body cap machined from billet aluminum.
Built-in billet aluminum separator piston provides an in-line gas pressure reservoir which eliminates the Suzuki rubber bladder.
This shock package includes the CNC machined Bling Ring Preload Adjuster Collar and Preload Bearing that will make preload adjustments easy.
Select the spring you want installed based on the load you plan to carry. For riders (and gear) less than 250 pounds we recommend the 7.6 kg/mm spring. If you regularly have more than 250 pounds the bike, you might want to use the 8.15 kg/mm spring. If you have any questions at all about this, please call.
You may choose to add the Hydraulic Preload Adjuster to make it the easiest of all. All you do is twist the knob. Includes mounting bracket for knob unit. (Some CA carb compliant models may need slight modification for mounting the preload adjuster.)
Low shock also available. This option will lower your seat height 1" without the need for lowering links. All other features of this shock are the same as the stock height.
Complete kit of OEM quality parts to replace the bearings and seals in the swingarm pivot.
The Battery Tender® Junior Selectable is much more than a trickle charger. It has a brain. It's lightweight, compact, and fully automatic; very easy to use, especially in small spaces. It will keep your Lead Acid, AGM or Lithium battery fully charged so that it is ready to go when you are
Replacement brush plate kit fits both original stock or aftermarket starter motor.
The Trail Tech Vapor Speedometer/Tachometer units are custom designed for an exact fit. They feature a bright white backlit LCD display, waterproof connections, and all parts needed for a complete installation. These units accept AC and DC power input, and automatically switch to internal power if external power is removed. Power connectors are included. Permanent solid-state memory guarantees that data is never lost, even without power. Units are available in black.
Trail Tech provides a one year warranty and unlimited free phone and email support.
Unit functions:
This high output stator will allow you to run brighter lights, heated gear, heated grips, etc. From ElectroSport
Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a plusher ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.
These great features combine to offer you a custom seat feel, and provide greater enjoyment and increased range for long commutes, or Dual-Sport rides!
The Complete Seats come assembled with an aftermarket pan and ready to ride.
The Commuter shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but is much more dished out towards the mid-point to distribute rider weight over a greater area. The passenger platform has been built up to help prevent the passenger from sliding into the rider.
The Commuter seat is the best choice for extended pavement riding and mellow offroad. The unique shape and added width will provide greater enjoyment and increased range on a long commute, or Dual-Sport ride!
| Width: | 13" (330mm) |
| Height: | Same as OEM |
Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a plusher ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.
Complete seats are built by Seat Concepts on a new seat pan and come ready to be installed on your bike.
| Width: | 10" (254mm) |
| Height: | Same as OEM |
The ProCycle seat was designed for both comfort and function. Our seat is built with an advanced Progressive Density Foam (Pd-F) for those long days in the saddle, and also giving you freedom to move while standing.
The wide and sturdy seat makes long rides more comfortable. The vinyl weave helps keep you cool by letting air flow between you and the seat. The front of the seat is narrower, giving you space for your knees when you're standing, while the sides have grip so you can hold on with your knees while riding.
We will build the seat for you in-house on a new seat pan so all you have to do is put it on and go ride. Choose the heated seat option and we will add a Seat Warmer during the build process.
| Width: | 11" (279mm) |
| Height: | Same as OEM |
Renthal chain lube is 100% lubricant, zero propellant. So this new 250ml bottle size combines high performance and value.
The all-new formula Chain Lube is specially designed to penetrate all parts of the chain. This all-condition lube is compatible with all o-ring and non o-ring chains.
These brake fluids are motorcycle approved DOT 4 brake fluid, and is specially formulated to exceed all DOT 3 & DOT 4 specifications. What this means to you is exceptional resistance to vapor lock and maintaining consistent lever feel during extreme brake use.
Protect your thumbs from blisters caused by riding on the inside of your grips.
Sold in Pairs.
A must have for lowered bikes.
Our complete foot peg assemblies. 1-3/4" lower than stock. No extra brackets that hang down below the frame. Easier on the knees. Wider platform Yamaha YZ style footpegs are stronger and give you firmer footing. Mount solid to the frame. No more 'droopy' feeling when standing on the stock pegs. Lowering your footpegs makes it easier to stand and less of a reach down to the bars when standing.
Now you can get our Low Pegs with MK4 Pivot Pegz or black Fastway ADV pegs (both Yamaha YZ pegs) installed!
This kit combines common wide platform Yamaha YZ/WR foot pegs with brackets that are custom made to fit the TW200. If you are tired of standing on the stock skinny footpegs, get yourself a set of these fat boys and have pegs that match the tires on your T-Dub! For ultimate comfort, order the Pivot Pegz kit!
Simply unbolt your stock brackets and bolt these in their place. The bracket on the right side (brake lever side) is shorter than stock to correct the offset in the stock pegs. On kickstart models, the stroke of the kickstart lever is shortened slightly. Should you ever need to replace the pegs in the future, simply order pegs for the Yamaha YZ or WR 250/450.
The SW-MOTECH center stand for your Yamaha Tenere 700 increases the versatility of your machine for more secure parking on various terrain while enhancing ease of maintenance. Robust steel construction provides sturdy support for the motorcycle and is powder coated black for enhanced durability and corrosion resistance. This high quality center stand is designed and engineered in Germany for seamless integration with the factory original components and easy operation utilizing a built in foot lever which increases leverage and decreases lifting effort.
Features:
Don't get burned! Giant Loop's ingeniously simple and effective exhaust shield protects bags and bodywork from heat damage. The Hot Springs Heat Shield helps avoid the meltdown, preventing bags and side panels from touching your bike's exhaust. It's the lightweight, universal heat problem-solver for virtually any motorcycle exhaust system. Backed by a Limited Lifetime Warranty.
Our Tool Tube mounts in place of the little stock tool carrier. The tube is made from 3 1/2" O.D. ABS pipe. It's held by 2 strong powdercoated steel straps. Both ends are sealed with waterproof expanding plugs. This is the ideal way to carry those items you always want to have with you on every ride. Tube is approx 13" long. Long enough to carry your Tire Iron Wrenches.
You can now order your Tool Tube with a Locking End cap, mini padlock and keys included, on the exposed end.
If you already have a Tool Tube you can order just the Locking End Cap and lock.
Class 10.9 steel rotor bolts provide excellent sheer strength and include medium-strength threadlock patches to securely fasten your rotor.
Includes all the fasteners for both front and rear rotors.
This brake bleeder makes bleeding your brakes a one man job.
The unique check valve allows fluid and air to escape while preventing air from re-entering the system.
The best product for those surfaces that mate together without a gasket. Like center cases, cam covers and the like.
Maxima light viscosity 3w 75-390 shock oil, 1 US Quart.
