For the frame drain on your XR650L ,extra protection for your motor! Strong magnet at the end of the plug picks up metallic flakes in your oil, protecting your engine!
Pivot Pegz have set a new standard in footpeg performance and quality and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty. Pivot Pegz aim is to build the best footpegs in the world and they really do perform as good as they look. Here's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever!
Low peg mounts from JNS Engineering. Your choice of a straight 1.5" drop or get that drop and a 1" rearward offset. You can use your stock pegs or click on one of the optional pegs that are made to fit the stock DR650 mounts.
These heavy duty steel mounts are pressed, welded and then powdercoated black for protection. Includes mounting bolts.
Note: These mounts are compatible with the SW Motech Center Stand by adding a 1/8" spacer behind the mounts.
These top of the line Adventure pegs from Warp 9 are 5" long and 2.5" wide. They will give your feet the perfect perch whether you are cruising down the highway or standing up hammering down a singletrack trail.
All the parts you need to freshen up your brake master cylinder. New piston, seals, return spring, boot and snap ring.
Made by Nissin, an OEM supplier in Japan
Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
EBC brake pads contain aramid fibers; these are man-made high-performance fibers used widely for their light weight, high strength, abrasion resistance and thermal stability.
Sintered Pads:
Includes front and rear brake pads.
Each kit includes all necessary rubber components and brake pins.
Each kit includes all necessary rubber components and brake pins.
Seal profile is engineered to create equal pressure in each seal lip; equalized seal pressure creates less drag and longer seal life.
Patented MAX-LIFE has a coefficient of friction up to 3 times less than the OEM seal material
Triple-lip seal design
Dyno-tested to last 3 to 4 times longer than OEM seals
Directional ribs allow seal to be installed easily
Kits include fork seals and dust wipers
Low friction 'triple lip' seal design. Oil seals last 3-4 times longer that OEM seals. Kit includes Fork Seals and dust wipers.
Sized perfectly for adult back-yard racing or fast/aggressive mini riders. This is the most important upgrade you can make for an adult sized rider. The stock suspension is too soft for most adults and aggressive kids. Fits stock shock.
The complete shock upgrade kit - a shock spring of your choice, Race Tech Gold Valve kit, detailed instructions and a bottle of quality shock oil to complete the job. Everything you need to transform your mushy stock shock into suspension that really works.
Recommended rates:
The correct spring rate for your weight will give a smoother more controlled ride. No more bottoming out, and improved traction and confidence off-road.
8.6 & 9.6 springs require an adapter which is included.
Recommended rates:
*Spring color may vary due to specification requirement and availability.
A precision fabricated bolt-on swingarm extension for the TW200.
This kit provides a 3” stretch without having to cut and weld your motorcycle. Heavy duty steel construction with a silver metallic powder coated finish.
This complete kit includes everything you'll need: mounting hardware, brake linkage extension, and a new longer 428x136L non o-ring chain.
Provides additional clearance for running larger ATV tires.
The complete fork upgrade kit - your choice of springs and Race Tech Gold Valves. Also includes a set of top quality fork seals and 5W fork oil to complete the job. Everything you need to transform your mushy stock forks into suspension that really works.
You can select from various straight rate springs to customize the package to your needs.
Stock Spring Rate for XR650L: 0.44 kg/mm
Lightweight, for reduced unsprung mass. Straight rate springs will give better control in the rough stuff. Sold in pairs.
DRZ400 E/S
A pair of Race Tech fork springs to dial in your front suspension to suit your weight.
Fits all DRZ400 models with conventional forks (not for SM)
Recommended spring rates:
| Rider Weight w/gear lbs. | Spring Rate |
|---|---|
| 90 or less | .42 |
| 90-119 | .44 (stock) |
| 120-150 | .46 |
| 150-180 | .48 |
| 180-220 | .50 |
| 220-250 | .52 |
| 250+ | .54 |
Finding the right riding height is super important for maintaining control of your bike at all times. If you feel like your bike sits a bit too high, you'll love the Zeta Anodized Lowering Link! It's a fantastic replacement for your OEM linkage, and it can help you lower your center of gravity, which often translates to better handling and a more comfortable riding experience.
Here are some great features to consider:
- Enhanced ground touch for better stability.
- Adjustable link lets you lower it by about 30 mm, depending on your model.
- Easy bolt-on design—just swap out your stock link rod.
- Crafted from high-quality 7000-series aluminum alloy with a sleek laser finish.
It's time to ride with confidence and comfort!
Innovative design makes tool easier and more secure to use than old fashioned pin-aligned drivers
Revolutionize your riding experience with Swiftkicker.
An adjustable kickstand for your motorcycle. Swiftkicker is built for offroad motorcycles, dual sports, and dirt bikes. Designed with the idea in mind that motorcycles should be able to take you anywhere, the Swiftkicker motorcycle kickstands help you do just that. You can set the length to anywhere in a six inch range of travel so you can stop anywhere without having to worry about having an even surface to park.
With just a flick of your toe, you can adjust the kickstand to the desired height, park your motorcycle, and be on your way.
No longer will you have to search for a rock or piece of wood to prop your motorcycle up with, or even worse, coming back to your bike to find it has tipped over from unstable ground.
The Swiftkicker is 100% manufactured in the USA from the highest quality components.
The billet 6061 head and the hard anodized tube are significantly stronger than the stock stand. An oversized foot will assure that the end of your stand stays where it belongs, rather than eight inches underground with your bike lying on top of it. The design is trail proven in the harshest possible conditions. Because nothing is indestructible, any of the kickstand components are replaceable at a lower cost than purchasing an OEM kickstand.
Measured from the center of the pivot to the bottom of the foot.
Fully encloses the chain to guide it onto the rear sprocket. Stainless steel hardware, anodized aluminum plate, and plastic buffer for low friction and noise. Saves expensive engine cases.
The chain slider protects the swingarm from contact with the chain. Replace yours before it wears through to the swingarm.
Quality steel rear sprockets. Choose 525 or 520. 41T to 50T
48 and 50 sprockets require removal or modification of your lower chain guide.
Chain Size Recommendations:
*Actual sprocket color may differ from image shown.
If your aftermarket exhaust is missing heat shield mounting points, this is the easy fix you’ve been waiting for.
Includes one stainless steel mounting bracket with M6 threaded nut, and one stainless steel hose clamp.
Fits exhaust approximately 1.1inch-2inch diameter. Trimming may be required for smaller diameter exhausts.
This is the gasket used between the header pipe and the stock muffler. This gasket is not needed for aftermarket mufflers!
The DG RST (Reduced Sound Technology) muffler is the quietest DG muffler and is designed especially for dual-sport machines (Just 84db @ 3200 RPM). A new baffle design dissipates sound waves reducing noise output in a very efficient manner. This new design also stretches out the time between muffler repacks. Included is a Stainless Steel mid-pipe, USFS Approved Spark Arrestor and a new Aluminum end cap.
This exhaust system is ideal for a racer on a budget that is not willing to compromise on performance! The T-4 comes complete with our stainless head pipe that works in conjunction with the silencer to produce more power from bottom to top. The use of stainless steel for the header pipe offers increased strength and should give years of trouble-free use. The silencer canister is easy to repack by removing the inlet cap screws and re-wrapping the silencer core. The T-4 meets all AMA sound restrictions.
Replacement shift lever with folding tip.
A set of replacement brake and clutch levers. Polished alloy.
Matte black 118mm x 85mm mirrors. Similar to stock size.
• 8mm thread
Sold In Pairs
Throttle cable routing on the XR650L gives you very little extra slack for raising the bars or adjusting them towards the rider. We now offer throttle cables that are 3" longer than stock allowing you to customize the bar position to your riding style.
These quality cables are made by Motion Pro.
This optically clear headlight guard is CNC cut for a perfect fit. It is made of durable aircraft grade 3/16" thick cast acrylic which resists harsh rock impacts, trail scuffs, and incidental scratches. Velcro fasteners hold the guard firmly in place and allow for easy on & off should it need an occasional cleaning. Installation is a quick five minute job, positioning template included.
This kit includes the all new Morimoto 4×6 LED headlight and pre-assembled JNS Engineering adjustable mounting bracket set. It’s a one beer, plug & play installation.
This is the best performing and highest quality headlight they currently offer.
The low beam pattern is bright, very uniform, and features a proper upper cut-off (Left Hand Drive, ie USA).
The high beam is amazingly bright eliminating the need for auxiliary lighting.
The materials, construction, and aesthetics are all top notch. You won’t be disappointed!
Low Beam: 20W, 2,400 Lumens
High Beam: 35W, 4,300 Lumens
Color Temperature: 5,000k
DOT Compliant
Beam Pattern: Left Hand Drive. (USA)
This kit includes a DOT LED headlight assembly with plug-and-play wiring harness, a specially designed adjustable steel mounting bracket, and all the required installation hardware.
How does this headlight compare to our original TW200 kit? First and foremost, this kit has SAE/DOT markings and a much wider/brighter high beam pattern. The low beam is very similar to our original kit: wide, flat, and bright but with more punch. The DOT headlight assembly has also proven to be more durable than the original headlight.
Low Beam: 30W, 2,800 Lumens
High Beam: 50W, 3,600 Lumens
Color Temperature: 6,000k
DOT & SAE Approved
CE, RoHS, ISO9002, IP67
No cutting, drilling, or wiring modifications! Installation takes 5 minutes.
Two colors to choose from, Chrome or Black. Light output and beam pattern is the same for either color.
Please note that this product is not compatible with the 1987 TW200.
This DOT kit includes LED headlight assembly with plug-and-play wiring harness, a specially designed adjustable steel mounting bracket, and all the required installation hardware.
No cutting, no drilling, no wiring modifications! Installation takes 5 minutes.
This kit is highly recommend over the non-DOT kit. The low beam has extra punch and a proper beam pattern cut-off. The high beam throws light far and wide. It’s already a crowd favorite!
Two colors to choose from, Chrome or Black. Light output and beam pattern are the same for either color.
This kit is not just a bulb, but an entirely new LED specific headlight! A specially designed adjustable steel mounting bracket replaces the stock unit. Included is a wiring harness and all the required hardware to make this installation quick and easy and entirely plug and play. No cutting, no drilling, no wiring modifications are necessary. The headlight features separate low and high beam projectors in a custom headlight shell designed specifically for this LED bulb.
This kit is available with either a chrome or black chrome reflector in the headlight.
Does not fit '87 TW200 because that year has a unique AC powered headlight circuit.
This kit includes the all new Morimoto 4×6 LED headlight and pre-assembled JNS Engineering adjustable mounting bracket set. It’s a plug and play installation however a small amount of trimming on the backside of the plastic headlight shroud is required.
This is the best performing and highest quality headlight they currently offer. The low beam pattern is bright, very uniform, and features a proper upper cut-off (Left Hand Drive). The high beam is amazingly bright eliminating the need for auxiliary lighting.
The materials, construction, and aesthetics are all top notch. You won’t be disappointed.
Low Beam: 20W, 2,400 Lumens
High Beam: 35W, 4,300 Lumens
Color Temperature: 5,000k
DOT Compliant
Beam Pattern: Left Hand Drive
This kit is not just a bulb, but an entirely new LED specific headlight! A specially designed adjustable steel mounting bracket replaces the stock unit. Included is a wiring harness and all the required hardware to make this installation quick and easy and entirely plug and play. No cutting, drilling, or wiring modifications are necessary. The headlight features separate low and high beam projectors in a custom headlight shell designed specifically for this LED bulb.
This kit is available with either a chrome or black chrome reflector in the headlight.
Check out the images for stock vs. LED patterns and brightness. (Images are of a DR/DRZ unit, but the light unit is the same as that on the XRL.)
This auxiliary light harness is specifically built for the DR650 using the highest quality materials and components. Wire lengths, component locations, and end terminals are all predetermined and assembled for you. No electrical expertise needed! The relay is wired directly to the battery and Posi-Tap connectors are used to tap in to the existing headlight high beam circuit.
This eliminates the need for a separate switch to operate your auxiliary lights. When your high beam is on, your auxiliary lights will be too. Back to low beam and those high-powered beams will be off so you don't bother oncoming vehicles. There's also an in-line fuse holder for safety and peace of mind. A simple one page instruction sheet is included.
This is a standard H4 bulb that has a 80 watt low beam and a 100 watt high beam. This is an easy lighting upgrade that should not over tax a stock charging system.
There is a lot of technology packed into this tail light/fender eliminator kit. You have programmable turn signals and Safety Brake Pulsing both built into this product.
You can enable or disable the safety brake pulsing feature.
This kit includes only the highest quality components, including the pre-installed 12oClockLabs processor board, which is made in the USA.
We recommend a "Fixed Rate Flasher" unit for use with this kit. When you install aftermarket signals it changes the load on a factory signal system.
This kit does not include parts to mount aftermarket turn signals. The pre-installed processor board allows the turn signals to be integrated in to the tail light.
Now available in the original version or the Ultra version. The original uses the front two emitters for low beam and then switches to the rear two emitters for high beam. The Ultra uses the front two emitters for low beam and then runs all 4 emitters on high beam at a reduced wattage. Wattage is 38 watts on low and 38 watts on high.
This bulb uses 4 Cree XHP 50 emitters, capable of more than 2500 lumens each. At 5000 lumens on each function, this is the brightest Cyclops H4 bulb.
*UNIVERSAL PART, PLEASE CHECK YOUR APPLICATION FOR FITMENT
Heavy-Duty clutch springs
Replace your worn out clutch with a high quality Clutch Kit. This kit includes new friction discs for your clutch pack.
Please note: kit includes friction discs only, steel plates and springs not included.
The idler gear is one of the few plastic components in the DR650 that can significantly impact engine performance if it fails or breaks.
This gear is crucial for driving the oil pump, which ensures proper oil circulation throughout the engine. In the absence of this component, complete engine failure may occur. While the idler gear is not frequently cited as a common failure point in the DR650 engine, failures have been reported, typically manifesting as either a fractured gear or stripped teeth.
During inspection, it is essential to check for any cracks, chipped areas, or missing teeth on the idler gear. Replacing the gear is a straightforward procedure, and it is advisable to do so while the clutch side case cover is already removed for other maintenance tasks, such as NSU screw replacements or clutch hub bushing replacements.
This component is a Genuine Suzuki part.
A direct replacement for the stock KLR hoses that tend to crack and leak after a few years.
These silicone hoses are custom made for us. Silicon hoses operate at much higher temperatures and pressures than other rubbers, they don't perish, and they look great!
Unless you have managed to bash yours on a rock, this is an item of pure bling, but hey, there is nothing wrong with that! This CNC Oil Filter Cover is made from A7009-T6 aluminum with the 'Zeta' logo machined into the front and anodized in blue to really stand out on your Yamaha. It's also lighter than stock.
Made from laser cut, medical grade, 304 stainless steel micronic filter cloth. This filter provides 200% more filter area than most other filters. Most high quality filters will pass particles in the 90 to 95 micron range, and some tested, as much as 300 microns. Sand is about 125 microns and a white blood cell approximately 25 microns. Scott's stainless filter catches items down to 35 microns "absolute". The pleat seam is welded, not glued like paper filters, increasing temperature resistance to 600 degrees F.
Billet plugs for your left side case.
Includes both the timing mark plug and the crankshaft access plug.
Gasket for the engine case cover over the clutch. Doing any clutch work, you probably want to replace this gasket so you don't have any leaks when you are all done with the project.
The Total Tune-Up Kit. All the parts you need to do a complete tune-up on your beloved beast.
A quality foam Air Filter to replace the stock one. Uses the same guide and frame as the stock unit. It requires foam filter oil to properly trap dirt particles. Don't forget the Evolution Air Filter Oil kit from No Toil.
Sold in 6 packs
Not legal for use on pollution controlled vehicles in the state of California.
Are you a fan of K&N air filters? Here's one built just for the TW200. Top of line filtering to keep that engine healthy for years to come.
Genuine Keihin spring, washer, and oring for the fuel screw of FCR and FCR MX carbs.
Just the parts…
Fuel screw spring, washer, o-ring (fuel screw not included)
Tried, true and tested the Power Commander continues to evolve with the Power Commander 6. Developed to simplify the user experience, PC6 makes choosing and tuning a map easier for the end user. All the same benefits you have relied on for over 20 years remain to keep you at the front of the pack.
The Power Commander 6 fuel injection tuning device allows you to optimize your fuel and timing curve (where applicable) giving you the confidence to roam freely. With fine tune adjustability and multiple inputs, the Power Commander 6 will keep your vehicle running at its full potential letting you concentrate on the journey ahead.
Featuring a plug-and-play setup, Power Commander 6 can be installed discreetly underneath your seat, cowl, dash or other location ensuring your ride looks as good as it runs. Removing the device reverts your vehicle completely back to stock. With the ability to store and switch between two maps on-the-fly (via the map switch accessory) and connect to various Power Commander accessories such as the Autotune, Quickshifter or POD-300, the Power Commander 6 gives you features and functions that provide you with the ultimate ride.
All PC6 models have an end-user adjustment of +/-15 in the FUEL table and +/- 8 in the timing table (if applicable). This adjustment is on top of the values that are in the BASE map loaded to the device. This BASE map can be any of the available maps from the Dynojet website, or those you may have received from a third party.
The New Power Commander V is loaded with tons of new features.
Their rear racks are great for adding the extra storage needed for your next adventure. They are the perfect size for a backpack or small duffel bag. Their steel racks are built to handle any riding style you throw at them, now Rotopax ready! This is the ENDURO Series CRF300L rear rack which measures 10 inches wide and 12 inches long.
Easy to Install
Simple, quick installation of this 1 pound rack made from rugged 1/8" 5052 Aluminum. A rigid 4-point mounting system, but still sleek and low allowing for seat removal with no hassles.
Features:
Simple, lightweight rack made from rugged 1/8" 5052 Aluminum, with a rigid 5-point mounting system.
Low profile allows for easy seat removal.
Features:
Note: Placement of this top rack does require removal of the stock tool bag.
DRZ400 rack is available in both a Utility and Sport version. The Sport version is 9" x 9" and the Utility is a full 2" longer for added storage space. Both of the S/SM racks have tabs so you can bolt the stock tool bag on.
Please select the rack for your specific model as the differences are significant
Locking End cap for the ProCycle Tool Tube. Mini padlock and keys included.
These wider seats from Seat Concepts help keep you comfortable on those long commutes or dual sport rides. The added width and improved foam density help keep your seat from being the item to stop you from going on those big rides or enjoying the bike.
The Complete Seats come fully assembled on an aftermarket seat pan, and are ready to install and ride.
| Width: | 9.5" (241mm) |
| Height: | Same as OEM |
New wider seat to help keep comfortable on that long commute or dual sport ride. The added width and foam density will help keep the seat from being an item to stop you from going on that ride or enjoying the bike.
The new updated 2.0 version has a sleeker shape and a better fit in the tank area.
Complete Seats come assembled on an aftermarket pan and ready to ride.
| Width: | 9 1/8" (232mm) |
| Height: | 1" (25mm) Lower than stock |
Good News: There’s finally a plug & play LED headlight conversion kit for your 2008-2020 WR250R and WR250X!
This kit includes a sealed LED headlight assembly with plug & play electrical connection, adjustable powder coated steel mounting bracket set, and mounting hardware.
Installation is a five minute, one beer exercise. If you can change a residential light bulb you will have no problem installing this conversion kit. We promise.
Please note that you will need to reuse your OEM upper headlight mounting grommet and two aim adjustment springs. Or add new ones to freshen up your whole headlight unit.
Low Beam: 2,100 Lumens, 20 Watts
High Beam: 2,800 Lumens, 30 Watts
Operating Voltage: 10V-30V DC
Color Temp: 6,000K
Lifespan: >50,000 hours
This USB device connects to a battery cable with an SAE connector just like the typical Battery Tender outlet, and allows you to charge your electronic devices. Input is 12 Volts, with an output to the USB port of 2.1A maximum, perfect for your phone or other USB devices.
The standard ring connector is a simple, quick connection with a fused positive ring cable and negative cable that attaches directly to your battery with an industry standard 2-pin, SAE connector.
The weather protected ring connector is a premium quick connect permanent battery lead with weather protected connection system and cable. It features 1/4"/M6 ringlets, 20" L, Industry standard 2-pin, heavy-duty SAE connector, 15A fuse, Cable max rating: 5 Amps, Cable remains flexible at below freezing temperatures; rated for -40°F/-40°C.
This is the brace needed to stabilize the wing like structure they call a front fender on the KLR – both generations. This simple bolt-on reduces wind buffeting and increases steering stability at highway speeds. It also helps carry the weight of a fender mounted tool bag.
Made from laser cut 5052 aluminum, then CNC formed and beautified with a shiny black powder coat. Easily mounts in a few minutes using the included stainless steel hardware.
ProCycle Plastics (formerly DSA) Rear Fenders include LED tail/brake light and license plate holder. Vacuum molded, these parts are a design improvement over stock.
This guard is designed to protect your TW200 headlight from rocks, branches, and any road/trail debris kicked up by the vehicle in front of you. It’s a one piece laser cut steel component with a sleek black powder coat finish. Mounting hardware is included.
Note: installation requires drilling two 1/4” holes in your plastic headlight fairing.
This new unit from JNS will protect your cases from the damage caused by a thrown chain, and will also keep your pants, boots or foot safe from your countershaft sprocket.
The case saver portion is laser cut from 0.25" aluminum and then has the 0.19" aluminum countershaft sprocket cover welded to it and the entire unit is powder coated black.
All the mounting hardware is stainless steel with machined aluminum spacers also included.
If you have a 16t front sprocket, mounting modification may be needed to fit. Install the case saver on the bike without the top spacer and bolt. This provides a little extra wiggle room. Add the top spacer and bolt after the bottom bolts are loosely threaded.
Chain guards experience degradation over time as a result of chain friction. To ensure optimal performance replace worn components with genuine Honda parts.
An OEM type replacement for the mighty XRL from the folks at Fuel Star. Single inlet that threads directly onto the stock fuel tank. Also works on the adapters that come on some aftermarket large capacity plastic tanks (like IMS).
Kit comes with a new Petcock, O-Ring, Fuel Line and Fuel Line Clamps! Everything you need for a complete fuel connection replacement.
A popular upgrade from the stock vacuum operated fuel valve. Manually operated. Must be shut off any time the bike is parked for more than a few hours. Fits stock tank or aftermarket tank and has both main and reserve. Fully rebuildable.
All of these lines are stronger and more durable than vinyl fuel lines and are resistant to swelling, UV light, as well as hardening and cracking.
Five-layer Greenshield® Barrier Technology cuts vapor loss and saves fuel, making it safe for the environment and fuel efficient.
1. Barrier tube - provides high heat and corrosive liquid resistance.
2. Greenshield® barrier - patent-pending technology provides the lowest permeation in the industry.
3. Adhesion layer - secondary protective barrier.
4. Reinforcement layer - spiral textile reinforcement provide strength and pressure resistance.
5. Cover - protect underlying components.
Get better range from your DR650 by adding an IMS 4.9 gallon fuel tank. Available in Natural, White, Black and Blue. Natural color is recommended if you wish to easily see the fuel level in the tank. Includes cap and fuel petcock.
ProCycle Rev Box increases the rev limit to 10,000 RPM. In addition, this unit offers a re-mapped timing curve which yields a noticeable increase to horsepower and torque over the stock CDI
This CDI box is a direct plug in replacement CDI. Simply locate and remove the stock CDI, and plug the unit directly into the wiring harness, no modification needed. Suitable for stock and modified machines
Clutch and Ignition covers made by B&B Eng. Formed from 2mm thick 5052 aluminum plate, selected because of its strength, corrosion resistance, excellent abrasion and impact protection. These will help protect your cases in the event of a bad fall.
These covers are attached to the engine cases with high quality heat resistance silicone adhesive
These covers will NOT fit early kick start only models that did not come standard with electric start. If you have added a kick starter to your bike that came with an electric start, covers will fit with no problem.
Warp 9's CNC shark fin rear rotor protector. To make installation super-easy this fin bolts to a brand new CNC machined caliper bracket. Just remove your existing caliper bracket and remove the pins, install them on this new one and then put the caliper and fin back on.
No longer need your speedo drive? Install an electronic unit? This CNC machined aluminum unit will replace the stock speedo drive on the front wheel keeping things properly spaced and sealed up.
To suit a 20mm Axle.
Before placing your order please ensure you check the diameter of the axle, as the earlier models may have different sized axles.
Includes all wheel bearings, new dust seals. The rear kit includes the bearing and seal for the cush drive hub (sprocket carrier). All bearings are sealed on both sides.
Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.
Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.
Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.
Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.
Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.
The rubber coated outside diameter creates an optimum seal at the hub.
Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.
| Description | QTY per Kit |
| Ball Bearing | 3 |
| Seal | 2 |
The Clymer shop service and repair manual. It has all the necessary info to do any maintenance or repairs to your XR650L.
Replace these any time you feel excessive play in the sprocket hub.
Excessively worn dampers can cause the cush hub bearing to fail - which will ruin your sprocket carrier.
Sold as a full set.
Thread Chasers are designed to clean and re-cut damaged aluminum threads.
This kit contains the two sizes most common on metric motorcycles, M6x1.0 and M8x1.25.
Thread Chasers also remove dirt and metal shavings that become captured in thread grooves.
Uses 8mm or 10mm hex sockets, a Must for all tool kits.
32-Blade Dual-Reading Tapered Combination Feeler Gauge Set
Replacement Inner Tubes for your VanVan or TW200. Always a great idea to carry a spare on your adventures as the rear tube is often hard to find.
A set of front and rear brake rotor bolts.
Class 10.9 steel rotor bolts provide excellent sheer strength and include medium-strength threadlock patches to securely fasten your rotor.
Each pattern is available in three advanced synthetic rubber compounds. This means you can have the optimum combination of strength, tackiness and shock absorption to suit every riding condition and individual style. Soft grip is extremely soft, giving you a very comfortable ride, great feel and reduces the chance of blisters; however, because the grip is so soft, it wears quickly. Medium is a compromise between firm and soft. Firm grip has the same feel as a stock grip, it is very strong and has very good resistance to tearing and abrasion. Half Waffle has waffle pattern in finger area for traction and diamond pattern on palm side to reduce blisters. Full Waffle: designed after the CR Honda® grip.
