Search Products

Includes all wheel bearings, new dust seals. The rear kit includes the bearing and seal for the cush drive hub (sprocket carrier). All bearings are sealed on both sides.

Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.

Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.

Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.

Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.

Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.

The rubber coated outside diameter creates an optimum seal at the hub.

Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.

Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.

Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.

Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.

Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.

Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.

The rubber coated outside diameter creates an optimum seal at the hub.

Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.

High Quality Replacement Wheel Bearings and Seals for your TW200.

Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.

Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.

Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.

Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.

Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.

The rubber coated outside diameter creates an optimum seal at the hub.

Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.

Each kit includes all necessary rubber components and brake pins.

Each kit includes all necessary rubber components and brake pins.

Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.

The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.

• Significantly improves response and feel over factory rubber lines
• Largest performance improvement for your money over any other braking upgrade
• Stainless steel hose resists abrasion and puncture
• Teflon core does not degrade over time like rubber lines
• PTFE Dupont 64 Teflon® hose
• Feature a heavy-duty stiffener sleeve and route just like the factory lines
• Proprietary, premium fittings
• Banjos utilizes a unique machined channel and sealing surface for leak-free installations
• R&D and engineered in the USA
• GBrakes USA controls the manufacturing process, ensuring the highest level of quality control

Direct replacement OEM front brake cable for TW200 with drum brakes.

• Sintered Pads are best for regular riding. Long life, and good performance in all conditions
• Sport Carbon pads are made for fast riding in dry conditions. Not recommended for mud, water, or sand
• Race Sintered pads are high performance race pad with superb durability similar to that of the sintered pad. Higher friction level and fade resistance. Diamond ground surface finish to speed bed-in. Comes with new pad pins. Race Sintered are designed for racing use only; not for street use

• Sintered Pads are best for regular riding. Long life, and good performance in all conditions
• Sport Carbon pads are made for fast riding in dry conditions. Not recommended for mud, water, or sand
• Race Sintered pads are high performance race pad with superb durability similar to that of the sintered pad. Higher friction level and fade resistance. Diamond ground surface finish to speed bed-in. Comes with new pad pins. Race Sintered are designed for racing use only; not for street use

Galfer USA produces several different brake pad compounds for all types of riding styles and uses. With over 60 years of friction material production and research, they have learned that one compound doesn’t always do the trick across the board. If you are just looking for an OEM brake pad replacement or a high performance race brake pad, they have you covered!

Set includes front and rear brake pads.

• Aramid fibers have high strength-to-weight, thermal stability and abrasion resistance to provide advantages over cheaper steel fiber-based products
• Provide excellent stopping power without noise and rotor galling, even on polished rotors
• Fingertip control and strong, predictable brake response

DOUBLE-H SINTERED METAL PADS
Provide maximum brake effect and last twice as long as organic pads
Feature the HH friction rating – the highest in the industry

A popular upgrade from the stock vacuum operated fuel valve. Manually operated. Must be shut off any time the bike is parked for more than a few hours. Fits stock tank or aftermarket tank and has both main and reserve. Fully rebuildable.

Locking End cap for the ProCycle Tool Tube. Mini padlock and keys included.

The GCAG Bottle Holster is designed to support many different bottles. The Bottle Holster can attach to their Uprising Soft Rack, Hardcore Soft Rack, or anything you can get the straps around. This is an easy and convenient method to carry extra liquids.

The Following bottles have been tested and verified:

• 1 Liter fuel bottles such as Primus, MSR, and Optimus
• 1.5 Liter fuel bottles from Primus
• 1 liter Nalgene bottles
• 40oz Thermoflask water bottle

Any bottle with a circumference of 11.5" or less will fit.

Features:

• Four straps that can easily go around any mount point.
• Top strap to run through any slotted cap to prevent the bottle from coming out.
• Pull string with keeper in the top to keep shorter bottles and bottles without a slotted cap from coming out.
• Made from 1000D Cordura. 

Simple, quick installation of this 1 pound rack made from rugged 1/8" 5052 Aluminum. A rigid 4-point mounting system, but still sleek and low allowing for seat removal with no hassles.

Features:

• 12" long by 10" wide
• Integrated turn signal mounts
• Use with or without stock grab handles
• 16 strap slots for securing cargo
• RotoPax mounting kit compatible
• All hardware and instructions included

Simple, lightweight rack made from rugged 1/8" 5052 Aluminum, with a rigid 5-point mounting system.

Low profile allows for easy seat removal.

Features:

• 12" long by 10" wide
• Integrated turn signal mounts
• 16 strap slots for securing cargo
• RotoPax mounting kit compatible
• All hardware and instructions included

Note: Placement of this top rack does require removal of the stock tool bag.

DRZ400 rack is available in both a Utility and Sport version. The Sport version is 9" x 9" and the Utility is a full 2" longer for added storage space. Both of the S/SM racks have tabs so you can bolt the stock tool bag on.

Please select the rack for your specific model as the differences are significant

• Fully welded construction from 16 gauge mild steel
• Powder-coated black textured finish
• Rigid 4 point mounting system (except off-road model rack)
• Hardware and detailed instructions included

ProCycle side panel guards to keep your saddlebags from fouling the side covers. Constructed from mild steel tubing that is powder coated black for nice long lasting good looks.

Add your favorite set of saddlebags for a very economical luggage solution.

Guards only, saddlebags sold separate.

CNC machined from 5mm aluminum 5083 plate with lots of slots to attach your Rok Straps (or other straps). This gives a considerably wider deck than the standard B&B Rack. Attaches directly to the B&B rack with four screws that are included. Available in either polished aluminum or a black polymer coating.

These plates are pre-drilled and countersunk from the bottom making installation of a RotoPax mount quick and easy.

Some older carry racks will not have predrilled holes in them to mount luggage plate in which it will require you to drill yourself (select pre2018 version)

 This is for the add -on Top Plate only.

Their rear racks are great for adding the extra storage needed for your next adventure. They are the perfect size for a backpack or small duffel bag. Their steel racks are built to handle any riding style you throw at them, now Rotopax ready! This is the ENDURO Series XT225 Serow rear rack which measures 10 inches wide and 12 inches long.

Easy to Install

• Works great for mounting Pelican and Seahorse cases, or any other hard case. Givi compatible.
• Holes are in place to accept Rotopax mount with no drilling required.
• Stainless steel mounting hardware and instructions included.
• Fabricated with mild steel, MIG welded, and finished with a semi gloss black industrial grade powder coat.
• Weighs 3 lbs, 10 inches wide, 12 inches long.
• Works with stock tool bag. This requires an extra hardware kit available for free by request only.
• Rear rack only, no Rotopax mount or side racks included.

Constructed from heavy-duty waterproof tarpaulin with durable heat welded seams. This coated material makes clean-ups a breeze. Roll-down tops create a waterproof seal and are held in place with heavy-duty ITW quick release buckles. Wide support straps are adjustable via hook and loop material to fit almost any width seat.

• Available in 20 or 30 liter capacity
• Sold in pairs.

Mondo Straps are named after the classic motorcycle movie, "Mondo Enduro". When they set out on their world trip they had hard luggage on their bikes. By the end of the movie the riders that were still pushing forward were all using simple straps and some homemade dry bags. The simple fact is soft luggage is more durable off road than hard luggage.

The Mondo Straps Kit has been designed to work with or without their Uprising Soft Rack. These straps allow you to use any bag you want for luggage. When installed properly you will be able to thrash about offroad and your luggage will stay put!

To use the Mondo Straps make a girth hitch around any mount point on your bike. Next, thread the flat runner back through the heavy duty metal cam buckle and pull it tight. The Mondo straps are easy on and easy off. The integrated tensioner system will keep your luggage in place no matter what terrain your adventure takes you on!

Kit Includes:

• 2 Heavy Duty Cam Buckle Tension Loops
• 2 Four Foot Runner Loops

You can add the double D ring loop to any 1" flat webbing system. This simple piece adds a lot of flexibility to any luggage system you are using. Instantly and easily create a mount point or adjustment point on almost anything. Double D Rings can be used as a secondary buckle and works the same way as a helmet strap. However, the double D rings should NOT be used as a primary means of securing luggage.

Available in 6 colors.

CONSTRUCTION FEATURES

• (2) Heavy Duty 1" Metal D Rings
• 1" Flat Nylon Webbing

Stamped from heavy gauge stainless steel, Giant Loop® Mounts bolt onto virtually any motorcycle, snowmobile, snow bike, ATV, UTV, SxS, 4×4—and even boats. These mounts help keep straps away from hot exhaust while shortening strap lengths for maximum stability and helps make installation of Giant Loop Saddlebags, Panniers, Dry Bags, and Tank Bags even easier. 

Sold as a set of two (2).

• DIMENSIONS: 2.5″ L x 1.75″ W (64 cm L x 44 cm W) Hole: 0.39” (10 mm)
• MATERIALS: Stamped heavy gauge stainless steel.

Quality steel rear sprockets. Choose 525 or 520. 41T to 50T

48 and 50 sprockets require removal or modification of your lower chain guide.

Chain Size Recommendations:

• 110 link chain for a 42 tooth rear sprocket
• 112 link chain for a 46 tooth sprocket
• 120 link for the 48 and above sprockets.
• 120 link chain will have to be cut to the proper size for the 48 and 50.

*Actual sprocket color may differ from image shown.

High quality steel sprockets.

Stock Gearing: 15/48-128x128

The chain slider protects the swingarm from contact with the chain. Replace yours before it wears through to the swingarm.

High Quality chain. Will need to be cut to fit your sprocket combination.

A precision fabricated bolt-on swingarm extension for the TW200.

This kit provides a 3” stretch without having to cut and weld your motorcycle. Heavy duty steel construction with a silver metallic powder coated finish.

This complete kit includes everything you'll need: mounting hardware, brake linkage extension, and a new longer 428x136L non o-ring chain.

Provides additional clearance for running larger ATV tires.

Lightweight, for reduced unsprung mass. Straight rate springs will give better control in the rough stuff. Sold in pairs.

• Rider and Gear up to 145 lb. = 0.47 springs → 24% stiffer than stock
• Rider and Gear 145-185 lb. = 0.52 springs → 39% stiffer than stock
• Rider and Gear 185-235 lb. = 0.58 springs → 56% stiffer than stock
• Rider and Gear 235-285 lb. = 0.63 springs → 66% stiffer than stock
• Rider and Gear 290 lb.-UP = 0.70 springs → 84% stiffer than stock

Race Tech has developed these fork springs specifically for the heavier weight of the KLR650.
Sold in pairs.

• The .43 springs are 7% stiffer than stock and will be a great choice for most riders
• The .48 springs are 17% stiffer than stock and will be a better choice for heavier riders
• The .52 springs are 30% stiffer than stock and will be a good choice for loaded adventure bikes or very aggressive riders

These will not fit the Tengai model.

Low friction 'triple lip' seal design. Oil seals last 3-4 times longer that OEM seals. Kit includes Fork Seals and dust wipers.

Finding the right riding height is super important for maintaining control of your bike at all times. If you feel like your bike sits a bit too high, you'll love the Zeta Anodized Lowering Link! It's a fantastic replacement for your OEM linkage, and it can help you lower your center of gravity, which often translates to better handling and a more comfortable riding experience.

Here are some great features to consider:

- Enhanced ground touch for better stability.
- Adjustable link lets you lower it by about 30 mm, depending on your model.
- Easy bolt-on design—just swap out your stock link rod.
- Crafted from high-quality 7000-series aluminum alloy with a sleek laser finish.

It's time to ride with confidence and comfort!

• Lighter and stiffer than stock, high quality shock spring.
• A proper rear spring will give a smoother more controlled ride.
• Available in a multitude of spring rates, one is the perfect fit for your bike and riding style.
• Stock spring is rated at 5.3 kg/mm for the CRF450L

Sized perfectly for adult back-yard racing or fast/aggressive mini riders. This is the most important upgrade you can make for an adult sized rider. The stock suspension is too soft for most adults and aggressive kids. Fits stock shock.

• 30% stiffer than stock
• Preset and stress relieved for long life
• Custom wound from aircraft quality spring steel
• Powder coated finish

Helps protect vulnerable fork tube and seal from dust, dirt, and corrosive elements. These are sewn into a tube and require that you drop your fork tubes down out of the triple clamp for installation. Can still be slid up for easy cleaning. Sold in pairs

This kit includes the all new Morimoto 4×6 LED headlight and pre-assembled JNS Engineering adjustable mounting bracket set. It’s a plug and play installation however a small amount of trimming on the backside of the plastic headlight shroud is required.

This is the best performing and highest quality headlight they currently offer. The low beam pattern is bright, very uniform, and features a proper upper cut-off (Left Hand Drive). The high beam is amazingly bright eliminating the need for auxiliary lighting.

The materials, construction, and aesthetics are all top notch. You won’t be disappointed.

Low Beam: 20W, 2,400 Lumens
High Beam: 35W, 4,300 Lumens
Color Temperature: 5,000k
DOT Compliant
Beam Pattern: Left Hand Drive

This is a standard H4 bulb that has a 80 watt low beam and a 100 watt high beam. This is an easy lighting upgrade that should not over tax a stock charging system.

There is a lot of technology packed into this tail light/fender eliminator kit. You have programmable turn signals and Safety Brake Pulsing both built into this product.

You can enable or disable the safety brake pulsing feature.
This kit includes only the highest quality components, including the pre-installed 12oClockLabs processor board, which is made in the USA.

• Plug and Play
• 7 Different Programmable Turn Signal Patterns 
• Safety Brake pulsing built in (Can Enable or Disable)
• Superbright LED's; For excellent brightness, even in direct sunlight
• License Plate Light built in
• License Plate Bracket fits the common USA license plates, sloted for maximum plate compatibility.
• Includes Mounting Hardware
• Saves about 2 lbs over the factory tail light setup
• Made In the USA

We recommend a "Fixed Rate Flasher" unit for use with this kit. When you install aftermarket signals it changes the load on a factory signal system.

This kit does not include parts to mount aftermarket turn signals. The pre-installed processor board allows the turn signals to be integrated in to the tail light.

Now available in the original version or the Ultra version. The original uses the front two emitters for low beam and then switches to the rear two emitters for high beam. The Ultra uses the front two emitters for low beam and then runs all 4 emitters on high beam at a reduced wattage. Wattage is 38 watts on low and 38 watts on high.

This bulb uses 4 Cree XHP 50 emitters, capable of more than 2500 lumens each. At 5000 lumens on each function, this is the brightest Cyclops H4 bulb.

• All metal construction for bases and collars
• Better thermal efficiency 
• Better beam pattern distinction between high and low beams
• 5600k
• 38 watts 
• Removable metal base plate for easy install.
• Screw on connectors at driver
• Standard H4 connector
• High/Low Beams

*UNIVERSAL PART, PLEASE CHECK YOUR APPLICATION FOR FITMENT

The Barkbuster LED Indicator Lights for Jet, Storm & VPS Plastic Handguards to increase your visibility and safety using 15 high intensity LEDs that mount directly to the plastic handguard shells. Super bright auxiliary signals will make your directional intentions clear to upcoming traffic. The LED indicators are very low draw and E marked for road use.

Features:

• High intensity LEDs with amber lenses
• Intended for use as indicators/turn signals
• E mark approved for use as an indicator light
• 15 LEDs per indicator amplifies your visibility to other traffic
• Enhances safety by imrproving clarity of planned directional changes
• Very efficient performance with low power draw
• Designed for use on the upper surface of Barkbusters Jet handguard plastics
• Compatible with the upper and lower surface of VPS & Storm plastics

What's in the box:

• Barkbusters LED indicators in amber (pair)
• Mounting materials
• Installation instructions

Please Note: Not compatible with the electrical system on the Honda Africa Twin CRF1000L

The standard ring connector is a simple, quick connection with a fused positive ring cable and negative cable that attaches directly to your battery with an industry standard 2-pin, SAE connector.

The weather protected ring connector is a premium quick connect permanent battery lead with weather protected connection system and cable. It features 1/4"/M6 ringlets, 20" L, Industry standard 2-pin, heavy-duty SAE connector, 15A fuse, Cable max rating: 5 Amps, Cable remains flexible at below freezing temperatures; rated for -40°F/-40°C.

The Clymer shop service and repair manual. It has all the necessary info to do any maintenance or repairs to your XR650L.

Made from laser cut, medical grade, 304 stainless steel micronic filter cloth. This filter provides 200% more filter area than most other filters. Most high quality filters will pass particles in the 90 to 95 micron range, and some tested, as much as 300 microns. Sand is about 125 microns and a white blood cell approximately 25 microns. Scott's stainless filter catches items down to 35 microns "absolute". The pleat seam is welded, not glued like paper filters, increasing temperature resistance to 600 degrees F.

Replace your worn out clutch with a high quality Clutch Kit. This kit includes new friction discs for your clutch pack.

Please note: kit includes friction discs only, steel plates and springs not included.

Gasket for the engine case cover over the clutch. Doing any clutch work, you probably want to replace this gasket so you don't have any leaks when you are all done with the project.

High quality stator cover gasket. Genuine Yamaha part.

Rebuilding your engine? Here is a complete gasket kit for your TW200. Includes: Head Gasket, Base Gasket, Stud Gasket, Head Side Cover O-Ring, two Valve Cover O-Rings, Base O-Ring, Stud O-Ring, Rocker Shaft O-Ring, two Cam Chain Tensioner O-Rings, Intake Manifold O-Ring, two Valve Stem Seals, Exhaust Gasket, Left and Right Side Cover Gaskets, Pump Cover Gasket, TDC Plug O-Ring, Crankshaft Nut Plug O-Ring, and Oil Filler Plug O-Ring.

Unless you have managed to bash yours on a rock, this is an item of pure bling, but hey, there is nothing wrong with that! This CNC Oil Filter Cover is made from A7009-T6 aluminum with the 'Zeta' logo machined into the front and anodized in blue to really stand out on your Yamaha. It's also lighter than stock.

The Total Tune-Up Kit. All the parts you need to do a complete tune-up on your beloved beast.

• Valve Adjustment Wrench
• Feeler Gauge set taper blades (.0012"-.040")
• Breather Filter
• 5-Pack of Oil Filters
• Magnetic Drain Plug
• O-Ring Kit
• Air Filter
• Spark Plugs

Keep your motor running right with fresh spark plugs!

NGK is one of the world's largest manufacturer of spark plugs, whose products are used as original equipment (OE) on countless motorcycle and automobile models.

• High-quality materials and superior construction for serious power and reliability
  • Pure alumina silicate ceramic insulator provides high strength and better heat transfer
  • Deep-seated copper core for a wider heat range
  • Nickel alloy tip for longer life
  • Trivalent metal plating provides superior anti-corrosion and anti-seizing properties
• Choosing the right high-quality plugs prevents fouling from running too cool and preignition from running too hot
• NGK plugs available for almost every application and riding style

Throttle cable routing on the XR650L gives you very little extra slack for raising the bars or adjusting them towards the rider. We now offer throttle cables that are 3" longer than stock allowing you to customize the bar position to your riding style.

These quality cables are made by Motion Pro.

A quality set of replacement throttle cables from Motion Pro

A set of replacement brake and clutch levers. Polished alloy.

Sold in 6 packs

• Compatible with many air filter boxes. Easy to install by drilling 1’’ holes in airbox housing and snap fitting vents in.
• May be cleaned and re-oiled
• More air flow allows you to add more fuel to your intake mixture, increasing performance.
• 1" Diameter

Not legal for use on pollution controlled vehicles in the state of California.

Are you a fan of K&N air filters? Here's one built just for the TW200. Top of line filtering to keep that engine healthy for years to come.

• Increased air flow over the stock air filter
• Designed to increase horsepower and throttle response
• Designed to fit inside the factory air box
• Larger surface area over foam filters which offers longer service intervals in dusty conditions
• Four layers of premium cotton gauze provides outstanding filtration
• Washable & re-usable, never wears out
• One filter will last the lifetime of your bike

Tried, true and tested the Power Commander continues to evolve with the Power Commander 6.  Developed to simplify the user experience, PC6 makes choosing and tuning a map easier for the end user.  All the same benefits you have relied on for over 20 years remain to keep you at the front of the pack. 

The Power Commander 6 fuel injection tuning device allows you to optimize your fuel and timing curve (where applicable) giving you the confidence to roam freely.  With fine tune adjustability and multiple inputs, the Power Commander 6 will keep your vehicle running at its full potential letting you concentrate on the journey ahead.

Featuring a plug-and-play setup, Power Commander 6 can be installed discreetly underneath your seat, cowl, dash or other location ensuring your ride looks as good as it runs. Removing the device reverts your vehicle completely back to stock.  With the ability to store and switch between two maps on-the-fly  (via the map switch accessory) and connect to various Power Commander accessories such as the Autotune, Quickshifter or POD-300, the Power Commander 6 gives you features and functions that provide you with the ultimate ride.

All PC6 models have an end-user adjustment of +/-15 in the FUEL table and +/- 8 in the timing table (if applicable). This adjustment is on top of the values that are in the BASE map loaded to the device. This BASE map can be any of the available maps from the Dynojet website, or those you may have received from a third party.

The New Power Commander V is loaded with tons of new features.

• USB powered from computer (9 volt adapter is no longer needed for programming)
• Gear input (allows for map adjustment based on gear and speed)
• Analog input (allows user to install any 0-5 volt sensor and build an adjustment table based on its input such as boost or temperature)
• With gear position input connected the PCV is capable of allowing each cylinder to be mapped individually and for each gear (for example: on a 4 cylinder bike with a six speed transmission there could be up to 24 separate fuel tables).
• 10 throttle position columns (up from 9 on PCIIIusb)
• Enhanced "accel pump" utility (increased adjustment and sensitivity ranges)

The Mikuni TM42-6 HSR flows 17CFM more than the TM40-6 and incorporates many upgraded features such as a roller-bearing slide.

All this means going even faster has never been so easy, say goodbye to hard starting, hesitations and flat spots.

Each kit contains float bowl gasket (or o-ring), float valve assembly (or float needle) and o-rings to rebuild one OEM carburetor body.

Chain guards experience degradation over time as a result of chain friction. To ensure optimal performance replace worn components with genuine Honda parts.

Low peg mounts from JNS Engineering. Your choice of a straight 1.5" drop or get that drop and a 1" rearward offset. You can use your stock pegs or click on one of the optional pegs that are made to fit the stock DR650 mounts.

These heavy duty steel mounts are pressed, welded and then powdercoated black for protection. Includes mounting bolts.

Note: These mounts are compatible with the SW Motech Center Stand by adding a 1/8" spacer behind the mounts.

The DG RST (Reduced Sound Technology) muffler is the quietest DG muffler and is designed especially for dual-sport machines (Just 84db @ 3200 RPM). A new baffle design dissipates sound waves reducing noise output in a very efficient manner. This new design also stretches out the time between muffler repacks. Included is a Stainless Steel mid-pipe, USFS Approved Spark Arrestor and a new Aluminum end cap.

• The latest EVOLUTION of the popular LV ONE: aggressive sound and style
• Clean laser-etched Leo Vince logo in an innovative carved design (for the carbon fiber exhaust: bright aluminum die-cut high-temp resistant Leo Vince adhesive logo)
• Asymmetric design and high-tempiresistant full-carbon fiber end cap
• Impact-resistant sandblasted oval AISI 304 stainless steel sleeve – titanium look
• TIG-welded stainless steel front cup
• Adjustable full-carbon fastening strap
• Removable dB killer, weight savings and flawless installation

DG Performance exhausts help your engine breathe better, resulting in increased throttle response, power and torque.

The V2 Series Slip-On muffler features:

• Lightweight aluminum body
• Stainless steel inlet tube
• TIG welded components
• Great new look

Standard sound level is approximately 98 db and quiet core inserts are available separately.

This Lightweight Slip-On weighs approximately 5.5 lbs and bolts directly to the stock headpipe.

It is equipped with a US Forest Service-approved spark arrestor.

This exhaust system is ideal for a racer on a budget that is not willing to compromise on performance! The T-4 comes complete with our stainless head pipe that works in conjunction with the silencer to produce more power from bottom to top. The use of stainless steel for the header pipe offers increased strength and should give years of trouble-free use. The silencer canister is easy to repack by removing the inlet cap screws and re-wrapping the silencer core. The T-4 meets all AMA sound restrictions.

Thread Chasers are designed to clean and re-cut damaged aluminum threads.

This kit contains the two sizes most common on metric motorcycles, M6x1.0 and M8x1.25.

Thread Chasers also remove dirt and metal shavings that become captured in thread grooves.

Uses 8mm or 10mm hex sockets, a Must for all tool kits.

32-Blade Dual-Reading Tapered Combination Feeler Gauge Set

• 95mm (3.75") long taper blades hardened and polished
• Manufacturer's lifetime warranty
• Dual marked: 0.03-1.00mm and .0012-.040 in.

Replacement Inner Tubes for your VanVan or TW200. Always a great idea to carry a spare on your adventures as the rear tube is often hard to find.

Pirelli's Corsa radial or bias-ply with maximum grip tread.

Superb corning and straight-line stability.

Exceptional wet-weather performance.

Tubless design.

Kenda's Dual-Sport tire designed for the 10% on-road, 90% off-road crowd.

• Tall, aggressive knobs enhance dirt performance without compromising street performance
• Stiff bead and sidewall for better stability and cornering control
• Works best on medium to hard surfaces
• Tube-type (TT)
• Dot approved
• 6-ply

The Shinko 244 is a very popular tube-type upgrade for the front tire on the TW200 or the VanVan. DOT approval coupled with excellent performance both on and off-road make this tire a winner!

The 244 Series dual purpose street and trail tire is designed to be equally at home on dirt or pavement.

• Adventure Trail
• Dual purpose street and trail design
• Designed to be equally at home on dirt and pavement
• DOT approved

Available in 5.10-18 (69P load / speed rating) and 4.60-18 (69S load / speed rating).

The 244 Series Dual Sport street and trail tires were designed to be equally at home on dirt or pavement. Great value.

• DOT approved, tube type
• 4-ply rating
• All sizes designed for front or rear fitment

A set of front and rear brake rotor bolts. 

Class 10.9 steel rotor bolts provide excellent sheer strength and include medium-strength threadlock patches to securely fasten your rotor.

Class 10.9 steel rotor bolts provide excellent sheer strength and include medium-strength threadlock patches to securely fasten your rotor.

Includes all the fasteners for both front and rear rotors.

Each pattern is available in three advanced synthetic rubber compounds. This means you can have the optimum combination of strength, tackiness and shock absorption to suit every riding condition and individual style. Soft grip is extremely soft, giving you a very comfortable ride, great feel and reduces the chance of blisters; however, because the grip is so soft, it wears quickly. Medium is a compromise between firm and soft. Firm grip has the same feel as a stock grip, it is very strong and has very good resistance to tearing and abrasion. Half Waffle has waffle pattern in finger area for traction and diamond pattern on palm side to reduce blisters. Full Waffle: designed after the CR Honda® grip.

Having the proper fork oil level is imperative to the handling of your bike. Setting the correct fork oil level is a snap with this fully adjustable gauge. The adjustable aluminum level plate can be set from 0 to 295mm. The oil reservoir has single milliliter markings up to 60ml.

Being able to accurately tune your forks by adjusting the oil level can make them better resist brake dive or bottoming. Oil level should be thought of as a fine tuning method to make your choice of spring rate work perfectly for your bike.

Protect the most vulnerable components of your bike with this pair of R&G Engine Case Covers, now available in kit form. Engineered with 4mm polypropylene for superior strength, longevity and sleek aesthetics, these protective guards complement all other R&G crash gear perfectly.

Features:

• Crafted from 4mm polypropylene
• Bolt on installation atop existing engine case cover
• Low profile for maximum ground clearance
• Ultra lightweight with matte black finish
• Meets or exceeds AMA racing specifications
• AMA approved for use in any regulated event

Adventure bike heaven is off-road headed down a dirt road or a trail. If that is your dream, then as you know, you are going to fall. Sometime, someplace, it will happen, so be prepared! Save your bike before it happens.

SW-Motech makes some of the finest protection equipment available. The set-up for the Twin is available in a standard black powder coating or a semi-polished Stainless-Steel tubing. Both sets will protect the vital components of your motorcycle as well as you from damage incurred during a fall, slide or crash. They will preserve the frame, radiator, bodywork and other critical components from touching down with robust tubular steel. The black kit uses 27/21 mm tubing while the Stainless uses straight 22 mm tubing throughout.

Both configurations have a tight fit for great ground clearance and are designed to work seamlessly with other SW-Motech products like their Skid Plate/Engine Guard and SW-Motech Hawk light mounts. Three secure mounting points per side provide the necessary support that make these so strong. There is no drilling, cutting, welding or any other modifications required for mounting but still allows access to the oil filler, tool box and battery. Kit includes all necessary hardware and instructions and an aluminum cover to replace the OEM plastic cover at the lower mounting point on the left side.

Please Note that these Crash Bars are also compatible with the SW-Motech Skid Plate and the SW-Motech Centerstand.

• Protect vital engine parts and cases from rocks and debris
• Clear anodized for corrosion protection and good looks
• Skid plates made from 3/16" 5052 H-32 aluminum
• Smooth underside won't snag when crossing logs
• Oil drain hole
• Heat-treated chromoly steel clamps keep plates mounted securely
• All mounting hardware included

Enjoy maximum protection and durability with an SW-MOTECH skid plate. Fully welded aluminum construction is engineered in Germany to provide proper protection from impacts, abrasions and projectile debris. Multiple ventilation slots on the front, sides and bottom of the skid plate permit maximum air-flow to keep your motor cool. Drilling, cutting, welding or any other permanent modifications are not required.

Features:

• Debris and collision protection for the engine 
• Fully welded 4mm thick aluminum plate / black side made of 2.5mm thick aluminum
• Efficient underbody protection of stone-chipping and collision
• Provides protection for the vulnerable oil pan & lower engine cases
• 100% bolt-on, no drilling, cutting, or any other permanent modifications needed
• Ventilated design maximizes air-flow to prevent overheating
• Silver
• Designed & engineered in Germany

What's in the box:

• SW-MOTECH skid plate engine guard
• Mounting hardware 
• Installation instructions

The X-Grip is a frame guard that allows the rider to both protect the frame of the motorcycle from wear as well as adding more grip to the bike.

Made from a dual injected mold; The outer plastic is durable polycarbonate while the inner plastic is durable yet playable and offers incredible grip.

Available in 2 colors

Provide protection for your motorcycle’s front brake and clutch levers with Barkbusters aluminum bar lever protection handguards. Designed specifically for the Tenere 700, these guards feature heat treated full wrap aluminum backbones that mount at two points on each side for strength. Prevent costly damage to your motorcycle with Barkbusters aluminum bar lever protection handguards.

Features:

• Two mounting points provide secure protection
• Full wrap guards
• Heat treated aluminum backbone bars
• Easy installation
• Compatible with all Barkbusters deflector guards (not included)

Add Plastic Handguards for a complete kit.

Replacement handguards for your Cycra set up. Injection-molded high-impact plastic replacements. Includes all hardware needed for mounting.

All that you need to repair and inflate your tire on the road or trail.

• Padded nylon zippered carrying case easily stores inside fanny pack or tool compartment
• Everything needed to repair and inflate tire on the road or trail
• 4" inflator hose accepts threaded cartridges only
• Each cartridge produces 8-9 psi
• Made in the USA

Kit includes:

• 1 - large oblong patch
• 2 - medium size patches
• 3 - small patches
• Thumb buffer
• 0.50 oz tube of rubber cement
• 5 - 4" rubber insert strips
• Insertion tool with screwdriver handle
• Reamer/rasp tool with screwdriver handle
• 3 - 16 gram 3/8" threaded CO² cartridges
• CO² 4" inflator hose

CO² cartridges cannot be transported on an aircraft.

This great tire gauge measures from 0-100 psi.

Has a back-lit display, and a front light to help locate the tire valve.

Select from psi to kPa units of measurements.

Replaceable batteries and automatic shutoff

CE approved and CARB compliant.

Very accurate.

• Innovative multi-use tire tool set
• Breaks the bead on most street and off road motorcycle tires
• Integrated tire spoon for tire removal and installation
• Light weight and compact size is perfect for tool packs
• Ergonomic handles with crossguard to keep hand from riding forward
• Forged 7075-T6 aluminum construction for strength and durability
• Black anodized finish
• Patent pending

Available in 9.5" aluminum (ideal for travel) and 16" forged steel (useful in a home shop/garage)

Based on the wildly popular Race Tech Suspension Seminars taught by Paul Thede around the world, this step-by-step guide shows riders how to make their bikes handle like the pros. Thede gives the lowdown on all types of suspension, including cartridge and non-cartridge forks as well as dual-chamber and nitrogen-charged shocks.

The three forces of suspension, testing procedures, even the black arts of chassis geometry: This explains it all. The book provides step-by-step photos of suspension disassembly and assembly as well as a detailed troubleshooting guide for dirt, street and track.

• Six class 10.9 steel sprocket bolts with matching factory-style metal locking Fuji nuts
• Each sprocket bolt has medium-strength threadlock patches for a double lock
• Includes Allen key insert that adapts 8mm T-handle or socket to proper Allen key size for easy installation and removal
• PART #2401-0941 is made to match stock CRF sprocket hardware with 14mm nuts but will work with most Japanese models

Construction Features:

• Heavy Duty 1" Metal Ring
• Heavy Duty 1" Nylon Webbing
• Available in multiple colors
• Thin Black option is made of their lightweight webbing for low profile pannier brackets.

The simplest piece they make, in a 3, 4, 6, 9, 12 or 15 foot length. This is the runner they use on the bag snake and the side bag haulers.

This piece can be added into any luggage hauling scheme you can dream up.

SPECIFICATIONS:

Construction is a simple piece of 1" Nylon webbing with a loop sewn into one end.

They use the 4 foot length in the side bag hauler kits and the 6 foot length in the bag snake kits.

The tension system integrated in this loop is a Green Chile innovation. Their elastics are custom woven inside tubular nylon webbing. This gives you all of the advantages of adding tension to a strap while maintaining the full strength of nylon webbing. You can add their cam buckle tension loop to any 1" flat webbing system and have an instant upgrade. 

CONSTRUCTION FEATURES

• Heavy Duty Cam Buckle rated for 2000 pound load capacity
• Heavy Duty Rectangle Ring to assist in managing slack in the webbing
• Climb-spec tubular nylon webbing body

Patent Pending

Antigravity Batteries introduce the ground-breaking "RE-START (RS)" line of batteries. These are the first batteries with built-in jump starting! They intelligently monitor their status, and just before going completely dead, puts itself to sleep with just enough energy to get your vehicle started again. Simply press the RE-START button located on the battery, then start your bike and ride away!

These are an extremely lightweight (2.3 lbs.) and high-powered Lithium-Ion replacement battery for motorcycles. These batteries offer the first Battery Management System (BMS) found on a powersport battery and includes low-voltage cut-off, over discharge, over-charge, and thermal protections with real time lithium-ion cell balancing. Highly recommend using a lithium charger to maintain the life of the battery.

3 Year warranty

Product Size is just 5.9"L x 3.5"W x 3.74"H. If you need spacers, select the optional Foam Kit to pad the battery in the battery box.

Open Trail Terminal Tender blocks allow you to add up to six different accessories on your battery.

Features:

• Fits any 12v powersports battery with square posts
• Three mounting options: side, front, and top
• Includes two blocks (+) and (-) and 8 button head bolts

• Restore the factory shine with a superior detailer specifically formulated for the powersports industry
• Cleans, polishes and conditions plastic, fiberglass and painted surfaces
• Also effective as a light lubricant for cables and levers
• Fresh, clean scent

Motion Factory Racing patented Flex-Mount Footpeg System provides superior grip and allows your foot to flex forward and back with the movement or your motorcycle.

One of the key features of Flex-Mount Footpegs is their unique flex-mount design. This design allows the footpegs to absorb shocks and vibrations, reducing fatigue and improving overall comfort during long rides. Additionally, the adjustable height and angle options ensure a personalized fit, allowing you to find the perfect riding position for maximum control and stability.

The bushings act like the suspension on your bike. With bushings, there are a couple of things to think about. The more firm the bushing the more durable and longer it will last. They use a durometer, a hardness scale 0 being the softest and 100 being the hardest. They don't go below a80 because they found that durability isn't great below this but have tested as low as a60 bushings. A bigger person that rides enduro-style terrain might want an a96 or a98 rated bushing. A lighter person might want the opposite but in the end, it comes down to personal preference. 

They put an a90 bushing on all new mount setups so people can get a good feel for their mid range option. The bushings are high quality yet inexpensive (they achieve this because they use skateboard bushings that are already developed and produced in massive quantities around the world) and a wear item designed to be replaced each season or depending on how hard or often someone rides.  

Complete mount system includes: 

• 6061 Aluminum ADV Platforms (65mm wide x 107mm length) 
• Stainless steel mounts
• Sleeve bearing (8x10x20mm) included for 8mm OD' footpeg pins. 
• Right and Left spring included. 
• Chromoly steel spindles with reusable thread locker. 14mm wrench. Torque spec 40 ft/lbs 
• A90 (medium flex) rated bushings
• Cleats and stainless steel machine screws. M3x18mm. These can simply be replaced by going to your local hardware store when damaged or worn out. 
• Bushing bolts. 8mm Allen wrench. Torque spec 30 ft/lbs

 They designed their hardware to bend rather than break in a significant impact. A wrench or adjustable wrench will quickly and easily bend the bolt back straight. Please avoid using a hammer. A little leverage from a long-handled wrench or pipe will do the job. The whole system is rebuild-able and serviceable.

They Fit Kawasaki KLX110 and Yamaha TW200 however some of these bikes may need a little modification by yourself, Please check the size carefully before you buy. If you make mods to the footpegs for fitments it will void all warranties and return policies. 

The SW-MOTECH center stand for your Yamaha Tenere 700 increases the versatility of your machine for more secure parking on various terrain while enhancing ease of maintenance. Robust steel construction provides sturdy support for the motorcycle and is powder coated black for enhanced durability and corrosion resistance. This high quality center stand is designed and engineered in Germany for seamless integration with the factory original components and easy operation utilizing a built in foot lever which increases leverage and decreases lifting effort.

Features:

• Robust steel construction
• Attractive powder coated black finish adds corrosion resistance & durability
• Improves parking stability and versatility on various surfaces
• Significantly reduces the risk of a tip over when used on softer terrain vs side stand
• Integrates perfectly with the factory original components
• Easy to use German design uses leverage to make lifting a cinch
• Foot lever increases leverage to aid in lifting technique
• Does not require cutting, drilling or any other permanent modifications
• Allows on the road maintenance without a paddock stand
• Eases chain and tire maintenance
• Double retention spring ensures safe operation even if one spring fails

All the advantages of a flatslide pumper carburetor at a much friendlier price than a Keihin FCR.

Our complete genuine Mikuni TM40 pumper carburetor kit comes with alloy adapter rings bonded to the carburetor body for a firm reliable fit in the stock air boots. We also include a remote mounted choke knob, complete instructions along with a wide range of main jets and pilot jets for fine tuning or to accommodate bikes with extensive modifications.

Cat Crap is the #1 voted anti-fog on the market. Lens cleaner and anti-fog in one. Works for all lenses, eyewear, goggles, helmet visors, etc.

• Quickly dissolves dirt and grime without harming filter glues
• Simply spray on, hose off and re-oil filter
• Available in 15-ounce net wt. aerosol can