Billet plugs for your left side case.
Includes both the timing mark plug and the crankshaft access plug.
Genuine Yamaha replacement gaskets for your side covers.
Made from laser-cut, medical-grade, 304 stainless steel micronic filter cloth, this filter provides 200% more filter area over many paper filters, catching debris down to 35 microns. The FLO filter pleat seam is welded and able to withstand up to 600 deg. F. Filter maintains consistent flow under all conditions including extreme heat, the presence of water and cold start-ups where paper filters can flow so poorly that they often cause the bypass valve to open and allow unfiltered oil to enter your engine.
This cleanable oil filter should be the last one you ever purchase.
This is all you need to not only change your oil, but protect your motor as well. We include a magnetic drain plug in the standard kit, to help catch stray metal pieces, a 5-pack of oil filters, and new O-Rings to replace any you have that may be leaking or worn.
Standard kit includes:
Includes forged Wiseco 83mm Piston (83.00/+4.00 10.5:1), Rings, Clips, Pin.
Top end gasket set.
Get better range from your DR650 by adding an IMS 4.9 gallon fuel tank. Available in Natural, White, Black and Blue. Natural color is recommended if you wish to easily see the fuel level in the tank. Includes cap and fuel petcock.
You want a lighter replacement for your heavy steel stock tank? Don't need the extended range (or bulk) of a big tank? The 3.7 gallon tank from Clarke might be just right. It's almost 5 lbs lighter and holds close to 1/2 gallon more fuel than stock to increase your range by about 20 miles. Fits with your stock petcock, Pingel or Raptor petcock.
If you need a replacement cap for your Acerbis tank, why not go bling? These caps have a carbon fiber pattern molded into them that is extremely realistic. Looks like the real thing. Topping off the cap is a CNC Machined metal vent cap. This eliminates the need for a lengthy vent tube that gets in the way. The vent cap allows air to vent into the tank but does not allow fuel to splash out during normal use or during a tip over.
These caps fit Acerbis tanks only.
If you're like us, you hate the long floppy vent hose hanging off the cap of your aftermarket tank.
This one-way vent cap replaces the long hose with a short one only about 2" long. It allows air into your tank but prevents fuel from sloshing out.
Machined from billet alloy and anodized for good looks.
Not for stock fuel tanks!
You’d be amazed at the dirt and debris that can work its way into your gas can – and from there, your fuel tank. Twin Air’s monofilament screen pocket inserts in your tank to catch particles as small as 40 microns (.00165”) while allowing the gas to flow freely.
The flange is custom-sized for each modern 4-stroke model to ensure a leak-proof seal. Just remove the filter periodically, turn it inside-out, and clean out the debris that could have been in your engine.
Will not work with factory locking gas caps.
Inside tank inlet diameter must be approximately 43.5mm (1.71") to fit.
The Rally windscreen from Parabellum is the perfect protection from wind and debris without sacrificing technical off-road capabilities. This is an upright rally type windscreen that looks aggressive and performs well under all types of riding. Designed primarily for the off-road / dualsport enthusiast, this shield keeps pressure off the rider's chest while commuting from home to adventure and back.
Mounting is accomplished by drilling two holes on each side of your headlight cowl using the provided template. 13.5 inches tall, 11.5 inches wide at the bottom, and 8.5 inches wide at the top. Made from military aircraft grade cast acrylic.
The Rally windscreen from Parabellum is the perfect protection from wind and debris without sacrificing technical off-road capabilities. This is an upright rally type windscreen that looks aggressive and performs well under all types of riding. Designed primarily for the off-road / dualsport enthusiast, this shield keeps pressure off the rider's chest while commuting from home to adventure and back.
This windscreen mounts securely to the three stock windshield holes as well as the two side cowling mounts. The shield is 14 inches tall, 13 inches wide at the bottom narrowing to 11 inches at the top. Made from 3/16" military aircraft grade cast acrylic.
The touring windshield from Parabellum has been designed, developed and tested using all the knowledge and experience of the KLR riders in their own shop. Using the stock mounting points as well as the cowling mounts increases the rigidity of the shield.
All new fasteners are included. This new design allows you to move your handlebar to different positions and will not interfere with a stand-up position for off-road use.
This shield is constructed of 3/16" military grade cast acrylic that is 17 inches wide at the bottom tapering to 16 inches at the top.
Parabellum LTD. has continued the highly demanded Rally Shield line by fitting up the 1993-present Honda XR650L. This is an upright Dakar Rally inspired shield, designed to protect the rider without interfering with off-road riding. For on-road riding the Rally shield protects the rider’s chest from fatiguing air blasts while keeping the head in clean air. Duck behind it in the cold or the rain to keep from experiencing the brunt of the elements. During off-road riding the Rally windshield protects the rider from mud, dust, roots, rocks, or branches without becoming invasive. Whether standing on the pegs or ducking behind it, you will be impressed at the protection it offers. Their Rally shields have been tested in the toughest conditions including an entire SORCS hare scramble season.
*The Rally shield for the XR650L is 12.5 inches tall 12.5 inches wide at the bottom and 8.5 inches wide at the top and is made from military grade 1/8 inch cast acrylic.
Transform your ride. MadStad's patented mounting system allows riders to adjust the height and angle of their motorcycle windshield resulting in much smoother airflow, better wind protection and a more comfortable ride than any fixed windshield can provide.
What's included in the kit:
Their complete drop-in system is custom-made for your bike and includes everything needed to mount and position the shield. Your bike will not require any modification.
The custom shield bolts to the brackets out in front of your instrument cluster. With the shield separated from the front of the bike you can adjust it for the optimum height, angle and airflow. This lets you set the shield for your particular height and riding position while pulling lots of air underneath it which is critical for smooth comfortable wind protection.
Transform your ride. MadStad's patented mounting system allows riders to adjust the height and angle of their motorcycle windshield resulting in much smoother airflow, better wind protection and a more comfortable ride than any fixed windshield can provide. Better still, this dual-sport version pivots the shield down and forward to get it out of your way for off-road riding!
What's included in the kit:
Their complete bolt-on system is custom-made for your bike and includes everything needed to mount and position the shield. Your bike will not require any modification.
The MadStad brackets bolt to the top of your fork clamps and are completely free of the handlebars. You can adjust the shield for the optimum height, angle and airflow for comfortable street and highway riding. When going off-road you can leave your comfort adjustment as-is and pivot the entire system down and forward in front of the headlight so you can get it out of your face completely. When it comes time to hit the pavement again, simply pivot it back up and you are back in street riding comfort mode.
Formerly DSA, now ProCycle brand, is a plastics kit in three colors - Black, White, and Blue, as well as Blue fenders with White side panels and Black fenders with White side panels. (headlight cowl not included).
Vacuum molded, these parts are a design improvement over the stock pieces. The side panels have a crisper, more angular look than the stock parts while the front fender is shaped like the DRZ400SM OEM front fender. Big enough to be functional without wind-steering the bike like the stock fender does.
Kits include front and rear fenders, a new LED tail/brake light and license plate holder, and both side panels.
Add a fresh new side panel hardware kit and an adhesive heat shield for a fresh off the showroom floor look.
Add a stock Suzuki headlight cowl if you are doing a complete color change to your DR (must select plastic kit with head light cowl option)
Front fender from ProCycle Plastics (formerly DSA) is shaped very much like the OEM DRZ400SM front fender. Big enough to be functional without wind-steering the bike like the stock fender does. Vacuum molded, these are a design improvement over stock. These are fully compatible in any combination with the original factory plastic.
Quality parts from Acerbis. Replace those big white ones with black ones for a custom look, or you can just replace your trashed white ones with crisp clean new ones for that great stock look.
Depending on your application and preferences, more than one optional heat shield may be useful.
Quality replacement rear fender from Maier.
Provide protection for your motorcycle’s front brake and clutch levers with Barkbusters aluminum bar lever protection handguards. Model Specific, these guards feature heat treated full wrap aluminum backbones that mount at two points on each side for strength. Prevent costly damage to your motorcycle with Barkbusters aluminum bar lever protection handguards.
Features:
Add Plastic Handguards for a complete kit.
Fits Moose and other aluminum hand guards
For Straight 7/8" handlebar
Contoured alloy hand guards with inner mounts, allow space for the clutch cable and brake hose.
Note: This kit includes the handguards only. Deflectors sold separate, can be added by selecting color from drop down menu.
For DR650 or other models with long levers add the optional universal fit Spacer Kit so you don't have to cut the balls off the end of your levers when installing these handguards. (May require additional adjustment or modification on some models.)
This kit provides some much needed protection for both you and your big DR. Handguards and deflectors protect your hands while the skid plate and Case Armor will cover your baby's soft externals.
Bolt-on side case armor from Warp 9 Racing.
Made of High Density Polyethylene, the same very tough stuff they make their frame and axle sliders out of.
3mm thick complete side case coverage
6.5mm thick in the leading and bottom edges where impacts typically happen
Covers the oil filter which takes a lot of impacts on these bikes
Includes new longer case bolts to hold on the case guards
MotoPressor Tire Gauge comes with two chucks. A straight chuck for "easy to get at" valve stems PLUS a 45° chuck for those "not so easy to get at" valve stems.
We all know what a pain fuel Station gauges are. Most are woefully inaccurate and impossible to get onto a motorcycle valve stem. Enter the MotoPressor Tire Gauge…simply attach the MotoPressor Tire Gauge to your valve stem, attach the fuel station chuck to the inline fitting on the gauge and get an instant and accurate reading in PSI or KPA.
No need to switch between the gauge and air compressor hose! Added a little too much air to your tire? Simply press the air bleed button and adjust to your desired pressure.
NOTE: When swapping out the chuck, use plumbers tape on the hose thread. Wrap the thread, in a clockwise direction with 3 - 5 wraps of plumbers tape. Screw on the new chuck and tighten. Failure to follow these instructions will result in air leak!
MotoPressor Tire Gauge comes with a one year limited product warranty.
Specifications:
NOTE: Tubes can be run in Tubeless (TL) tires.
An Old School design that works great on today's Dual Sport bikes.
The rubber compound is engineered for high grip and long-lasting tread wear.
DOT approved, tube type, and might be the best value in a DOT knobbie.
Made for the true adventure rider, the K784 has everything you need to get you anywhere on or Off-Road.
This is a high-quality seat cover done by Moose for the TTR. This is a replacement cover only, no seat foam and you must install on your existing pan with existing foam. Strong marine-grade vinyl that's made to last. UV protected from sunlight for extended use and has double stitching for extra strength.
50mm step width provides better grip and control
The IMS Super Stock pegs are the perfect choice for both the daily commuter and the rider-in-training. Their mellow tooth design keeps you planted while preventing wear on your soles. They are also perfect for young riders who don't need or want a more aggressive option.
Wider foot pegs for sure-footed comfort.
17-4 cast stainless steel.
| Width | 1.97" |
| Length | 3.18" |
Light weight and strong. These DRC foot pegs have a wider platform for increased comfort and control. Cast from Chromoly steel for unbeatable strength and durability.
Your choice of an aluminum bolt-on foot pad or a steel weld-on unit. Each will make the footprint of the stock side stand considerably larger, preventing your DR from tipping over in soft terrain. The bolt-on unit is cut from aluminum and then powder coated black, it comes with stainless steel mounting hardware.
The bolt-on pad and does require use of a drill for installation. The weld-on pad will need to be welded to the stand and then the entire unit painted for corrosion protection.
Organic brake pads contain man-made high-performance fibers that are used for their light weight, high strength abrasion resistance and thermal stability. These Aramid fibers have a high strength-to-weight, thermal stability and abrasion resistance to provide advantages over steel fiber-based products. They provide excellent stopping power without noise and rotor galling but still provide fingertip control and strong, predictable brake response.
Double-H sintered metal brake pads feature the HH friction rating, the highest in the industry. These pads provide maximum brake effect and last twice as long as organic pads.
Semi-sintered pads have an all new recipe containing 30% copper by weight with an organic matrix. This design combines the long life of a sintered pad with the great feel and lack of rotor damage common with full-sintered pads. These can be used to replace Kevlar or sintered metal compound pads.
Set includes pads for both front calipers.
Premium quality EBC Rear brake shoes.
DOUBLE-H SINTERED METAL PADS
Provide maximum brake effect and last twice as long as organic pads
Feature the HH friction rating – the highest in the industry
Hate the handlebar mounted choke lever? Can't reach the choke knob? Does your Safari or IMS tank make using the choke difficult?
Our adjustable cable operated choke knob mounts to the left side engine case and works for either the stock BST or Mikuni TM40.
The Moab shock from Cogent Dynamics will change how you feel about your KLR. You may like it now, maybe even like it a lot, but you will absolutely fall in love with it once you mount up a Moab shock.
Spring duties are handled by a custom spring available in either Standard or Heavy-Duty weights. The Standard spring will be fine if you are under 250 pounds and don't ride with luggage or passengers often. Ride heavily loaded or with a passenger regularly and you will probably want the Heavy-Duty spring.
For a true comfort and performance package, we highly recommend upgrading your front suspension at the same time.
If you have '87-'07 KLR, you MUST order a new mounting bolt. Not required for 2008-2018 models.
Sized perfectly for adult back-yard racing or fast/aggressive mini riders. This is the most important upgrade you can make for an adult sized rider. The stock suspension is too soft for most adults and aggressive kids. Fits stock shock.
Race Tech shock springs in a wide range of spring rates to dial in your rear suspension to suit your weight (stock spring is 5.3 kg/mm). Recommended spring rates:
| Rider Weight w/gear lbs. | Spring Rate |
|---|---|
| 100 or less | 4.6 |
| 100-124 | 4.8 |
| 125-149 | 5.0 |
| 150-174 | 5.2 |
| 175-199 | 5.4 |
| 200-224 | 5.7 |
| 225-274 | 6.0 |
| 275 + | 6.3 |
The Pro-Series is the suspension performance pinnacle. Cogent takes Mojave’s best-in-class performance and adds an external reservoir.
The Pro-Series’ sophisticated reservoir with interchangeable valves and shims, provides more tune-ability at all speeds. It also improves internal pressure balance and temperature dissipation, giving long lasting performance regardless of the punishment you put it through.
Comes standard with the CNC machined Bling Ring Preload Adjuster Collar and a thrust bearing between the adjuster ring and the spring making preload adjustments easy.
The optional Hydraulic Preload Adjuster makes it even easier to adjust the preload. Just twist the knob. Includes mounting bracket for knob unit. (See last image) (Some CA carb compliant models may need slight modification for mounting the preload adjuster.)
Select the spring you want installed based on the load you plan to carry. *Spring color may vary due to specification requirement and availability.
For riders (and gear) less than 250 pounds we recommend the 7.6 kg/mm spring.
If you regularly have more than 250 pounds on the bike, you might want to use the 8.15 kg/mm spring.
Low shock also available. This option will lower your seat height 1" without the need for lowering links. All other features of this shock are the same as the stock height.
Sized perfectly for adult back-yard racing or fast/aggressive mini riders. This is the most important upgrade you can make for an adult sized rider. The stock suspension is too soft for most adults and aggressive kids. Fits stock shock.
Race Tech HP Springs have a high stiffness-to-mass ratio. In other words; the springs are light weight for their particular spring rate. This requires the finest materials and processing. Shot-peened and pre-set so they cannot sack out. All Race Tech HP Springs have the highest rate tolerances in the industry. These are the finest springs in the world-guaranteed.
This spring is 8.0kg/mm
OEM spring rates are 5.7-7.6kg/mm progressive style.
This complete fork upgrade kit includes stiffer fork springs and Race Tech cartridge emulators, as well as a set of top quality fork seals and fork oil to complete the job. Everything you need to transform your mushy stock forks into suspension that really works.
You can select from various straight rate springs to customize the package to your needs.
Custom developed by BBR Motorsports for the ultimate upgrade for mini four-strokes. Sized perfectly for fast/aggressive adult mini riders. This is the most important upgrade you can make for an adult sized rider. The stock suspension is too soft for most adults.
DRZ400 E/S
A pair of Race Tech fork springs to dial in your front suspension to suit your weight.
Fits all DRZ400 models with conventional forks (not for SM)
Recommended spring rates:
| Rider Weight w/gear lbs. | Spring Rate |
|---|---|
| 90 or less | .42 |
| 90-119 | .44 (stock) |
| 120-150 | .46 |
| 150-180 | .48 |
| 180-220 | .50 |
| 220-250 | .52 |
| 250+ | .54 |
Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. Designed by Rick at Cogent Dynamics on his high-tech suspension dyno, then tested and endorsed by KLR owners all over, these units have been given the seal of approval by the ProCycle staff for both performance and ease of installation. No disassembly of your forks, no drilling of damper rods. Just change the oil over to 5w and install the units under the springs and hit the trails.
If you weigh up to 250 pounds, select the .64 spring kit. If you are over 250 or carry lots of luggage, please select the .70 spring kit. Please call if you have any further questions.
All of these kits include DDCs, springs, fork oil and preload spacers.
Damping Rod style forks are notorious for being too harsh, too mushy and too easy to bottom. Gold Valve Cartridge Emulators remedy this problem by controlling the compression damping with a tuneable valve. The Emulator sits on top of the damping rod and is held in place by the main spring.
Simply put; Emulators make damping rod forks perform like well-tuned cartridge forks. Installation and tuning for any condition or rider preference is very straight-forward.
Simple to install and completely tunable for all conditions and rider preferences.
Damping Rod style forks are notorious for being too harsh, too mushy and too easy to bottom. Gold Valve Cartridge Emulators remedy this problem by controlling the compression damping with a tuneable valve. The Emulator sits on top of the damping rod and is held in place by the main spring.
Simply put; Emulators make damping rod forks perform like well-tuned cartridge forks. Installation and tuning for any condition or rider preference is very straight-forward.
Simple to install and completely tunable for all conditions and rider preferences.
*Comes with RaceTech adapter to properly seat the Gold Valve cartridge into to the top of the damper rod.
These Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. These units have been given the seal of approval by the ProCycle staff for both performance and ease of installation. No disassembly of your forks, no drilling of damper rods. Just change the oil over to 5w and install the DDCs under the springs and hit the trails.
Stiffer fork springs are recommended to get the full potential of the DDCs.
Lowers the rear suspension. Precision machined from billet aluminum and anodized.
*Important when lowering the rear suspension you want to raise the fork tubes in the clamps an equal amount of inches that the rear is being lowered. That way your bike will sit level when done.
Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.
| 1994 - Current: KLX250 | 1.25" |
| 1994 - 2019: KLX300 | 1.25" |
| 2020 - Current KLX300/ 300SM | 1.00" |
Throttle, Clutch or Speedo cables.
Replacement shift lever with folding tip.
Replacement shift lever from IMS with folding tip.
Original Suzuki factory replacement levers for your DRZ400S/SM/E
Order up your new levers here! If you keep breaking levers, you might want to think about a set of hand guards to protect them in case of a fall.
These are genuine factory Yamaha replacements.
Original Kawasaki factory replacement levers for your KLX230.
The Apollo Heated Grips are designed with an integrated adjustable thumb switch, which allows them to easily fit on any kind of motorcycles on the market. The integrated thumb switch gives control to the rider to adjust the temperature level while keeping hands on the bar for a safer ride.
Its wide temperature setting range will keep the rider comfortable under the cold riding conditions.
The 5 color LED display will enhance the visual look of the heated grips and will allow the rider to quickly know at which heat level the grips are set.
This system will also detect if the battery voltage is too low and will automatically shut down the heated grips in order to make sure the rider have enough power to start the engine or use the motorcycle.
Specifications:
Say goodbye to the frustration of fidgety handguard expansion plugs with Warp 9's innovative Tapped Handlebars.
These handlebars feature ends that are plugged and tapped with an M8x1.25 threaded insert, providing a secure and reliable mounting point for all aftermarket wrap-around handguards.
No more worrying about plugs pulling out or spinning during crashes; their robust design ensures you're good to go, even when you encounter obstacles.
Not using handguards? No problem they've got you covered!Each set of handlebars comes with aluminum grip guards and stainless bolts, offering protection for your grips and delicate throttle tube in case of a get-off.
Designed with an oversized 1-1/8 inch (28.6mm) clamping diameter that tapers down to 7/8 inch (22.2mm) to accommodate standard controls. Crafted from 7010 T6 aluminum tubing and featuring computer-extruded variable wall thickness, they effectively reduce vibration while enhancing overall performance and comfort.
Note: Does not include pictured bar mounts.
| Width | Height | Rise |
| 790mm | 101mm | 71mm |
| Clamp Area | Sweep | Bend |
| 142mm | 73mm | CR High |
Matte black 118mm x 85mm mirrors. Similar to stock size.
• 8mm thread
Sold In Pairs
The V2 Slip-On features new aluminum end caps. A USFS Spark Arrestor. DG offers 4 different Quiet Core Inserts to reduce exhaust sound. Lightweight at approximately 5.5 lb.s
Protect your head pipe from rock damage. This stainless steel spine clamps to your head pipe to add a layer of protective armor between your vulnerable pipe and those nasty rocks or logs. Fits the stock headpipe. Will fit the FMF head pipe with the addition of larger clamps.
This universal heat shield provides a great look at a great price.
If your aftermarket exhaust is missing heat shield mounting points, this is the easy fix you’ve been waiting for.
Includes one stainless steel mounting bracket with M6 threaded nut, and one stainless steel hose clamp.
Fits exhaust approximately 1.1inch-2inch diameter. Trimming may be required for smaller diameter exhausts.
For the frame drain on your XR650L ,extra protection for your motor! Strong magnet at the end of the plug picks up metallic flakes in your oil, protecting your engine!
Quality steel rear sprockets.
Color may vary based on manufacturer availability, quality will not be compromised.
High quality steel sprockets.
Stock Gearing: 15/48-128x128
Individual 14T, 15T or 16T front sprockets.
JT Sprockets are made from the latest generation of computer design and control metal cutting equipment for maximum durability. Front sprockets are made from chromoly SCM420 steel alloy. All sprockets are heat-treated and hand-finished to meet or exceed the highest possible quality standards.
Quality steel sprockets and EK SRO6 O-ring chain. We put them together to make a complete, affordable kit. Chain comes with clip type master link.
Quality steel front sprockets. Choose 525 or 520. Also available 'Wide Boss' JTF438 520 sprockets.
All 520 sprockets require a new retainer plate, please add on if purchasing this size.
These masterlinks fit the original OEM Suzuki chain. The original chain is marked DID 525 V8. Choose from Clip Type or Rivet Type.
This new and improved DOT kit includes LED headlight assembly with plug-and-play wiring harness, a specially designed adjustable steel mounting bracket, and all the required installation hardware. No cutting, no drilling, no wiring modifications! Installation takes 5 minutes.
We highly recommend this kit over the non-DOT and original DOT kit. The low beam has extra punch and a proper beam pattern cut-off. The high beam throws light far and wide. It’s already a crowd favorite!
Two colors to choose from, Chrome or Black. Light output and beam pattern are the same for either color.
Low Beam: 20W, 2,800 Lumens
High Beam: 35W, 3,600 Lumens
Color Temperature: 6,000k
DOT & SAE Compliant
CE, RoHS, ISO9002, IP67
Please note: Fits '87-'07 (Gen 1) only
This DOT kit includes LED headlight assembly with plug-and-play wiring harness, a specially designed adjustable steel mounting bracket, and all the required installation hardware.
No cutting, no drilling, no wiring modifications! Installation takes 5 minutes.
This kit is highly recommend over the non-DOT kit. The low beam has extra punch and a proper beam pattern cut-off. The high beam throws light far and wide. It’s already a crowd favorite!
Two colors to choose from, Chrome or Black. Light output and beam pattern are the same for either color.
This kit is not just a bulb, but an entirely new LED specific headlight! A specially designed adjustable steel mounting bracket replaces the stock unit. Included is a wiring harness and all the required hardware to make this installation quick and easy and entirely plug and play. No cutting, drilling, or wiring modifications are necessary. The headlight features separate low and high beam projectors in a custom headlight shell designed specifically for this LED bulb.
This kit is available with either a chrome or black chrome reflector in the headlight.
Check out the images for stock vs. LED patterns and brightness. (Images are of a DR/DRZ unit, but the light unit is the same as that on the XRL.)
This heavy duty aluminum bracket is specifically designed for mounting auxiliary LED lights to the front of your XR650L without interfering with your large aftermarket fuel tank. If your bike needs improved lighting this mount is the best place to start!
– 0.190″ 5052 Aluminum
– Laser cut
– CNC formed
– Powder coated black
– Includes stainless mounting hardware and JNS stickers.
LED auxiliary lights are sold separate.
From our friends at JNS Engineering, a very nice mount for a set of auxiliary lights on the front of your KLR650. Laser cut from 0.190" 5052 aluminum it is CNC formed and then powdercoated black. One of the best benefits is that it will not interfere with even the largest aftermarket fuel tanks. All included mounting hardware is stainless steel.
Clear lens, amber LED type lights. Short flexible stems. Very small, only 2 7/8" long. Requires a LED turn signal flasher to flash properly. 4 Pack
Convenient professional grade spoke wrench, a great addition to any tool pouch.
Recommended for use with Warp 9 wheels. Please measure nipple size to ensure proper fit.
The plastic fitting that secures the stock choke cable to the carburetor is delicate and easily broken. A broken fitting can cause hard to solve idling and running problems.
CNC machined from billet aluminum and anodized black or blue. If you want to retain your handlebar mounted choke this may be the solution.
These no longer fit the new version of the ProCycle Remote Choke Cable. Will not work with the long or short reach choke knobs.
This anodized billet piece, brings a touch of color to your bike. Available in red or blue, it replaces the stamped steel clevis that connects your brake pedal to the master cylinder.
A complete kit to mount your phone (or other electronic device) to your motorcycle. The universal cradle expands from 2.25" to 3.25" wide and 4.75" to 6.25" tall. The width is adjustable but fixed while the upper portion of the cradle is spring loaded to keep your device secured in the roughest conditions.
Select the mount option that works best for you. The mirror mount is shown in the photo at left and is a flat plate with an 11mm hole on one side and a RAM ball on the other. Simply remove your mirror, place the plate between your mirror and the perch and tighten it down.
The handlebar mount kit allows you to mount to either a 7/8" or 1-1/8" bar. Also includes hardware to mount to the back of a lever perch. See image at bottom middle for kit pieces.
The X-Grip with handlebar mount is best suited for larger phones up to 4.5" wide. The spring loaded X-Grip cradle expands and contracts, allowing for a perfect custom fit. Kit also includes a device tether recommended for outdoor applications.
Features:
ProTaper Pillow Top Grip with 3-D (Tri-Density) Technology. Try the grip with the technical advantage of three dedicated rubber compounds.
The difference between the original Pillow Top and the Pillow Top Lite is the overall diameter of the grip surface. The Lite offers a smaller diameter so the grips don't feel as large reducing fatigue in your hands while riding.
RotoPax holder made to mount a single Fuel and/or Water container.
This unique design adds strength and provides extra tightening power.
Use with included base plate or remove plate to attach mount direct by bolting up through the bottom or down through the top.
This DR650 Oil Filter Guard is CNC machined from solid 6061 aluminum, black anodized, and then custom laser etched with our logo.
It fits over the fragile OEM magnesium cover and provides great impact protection in the event of a tip over. Proudly made in the USA.
The Nomadic Rack for the early generation KLR650. CNC laser cut from 3/16" 5052 aluminum with a large 12" x 18" mounting surface area. Sand blasted and then powder coated black to give it a shot peened look. This rack is an easy installation with no modifications required. There are multiple strap slots for securing gear bags and cargo. Rack is compatible with RotoPax mount. All hardware and instructions included.
Packages available include Rack with the RotoPax Mount or if you really want it all, you can order the Rack, Mount and a Fuel or Water Container.
Nomadic Rack for the TW200. CNC laser cut from 3/16" 5052 aluminum with a large 12 x 10-7/8 mounting surface area. Sand blasted and then powder coated black to give it a shot peened look. This rack is an easy installation with a 4 point mounting system with no modifications required. There are multiple strap slots for securing gear bags and cargo. Doubles as a grab handle or tow bar. Is compatible with RotoPax mount. All hardware and instructions included.
You may purchase just the rack or you can order the Rack with the RotoPax Mount. If you really want it all, you can order the Rack, Mount and a Fuel or Water Container.
DRZ400 rack is available in both a Utility and Sport version. The Sport version is 9" x 9" and the Utility is a full 2" longer for added storage space. Both of the S/SM racks have tabs so you can bolt the stock tool bag on.
Please select the rack for your specific model as the differences are significant
Simple, lightweight rack made from rugged 1/8" 5052 Aluminum, with a rigid 5-point mounting system.
Low profile allows for easy seat removal.
Features:
Note: Placement of this top rack does require removal of the stock tool bag.
Our Tool Tube mounts in place of the little stock tool carrier. The tube is made from 3 1/2" O.D. ABS pipe. It's held by 3 strong powder coated steel straps. Both ends are sealed with waterproof expanding plugs. This is the ideal way to carry those items you always want to have with you on every ride. Tube is approximately 13" long.
You can now order your Tool Tube with a Locking End cap, mini padlock and keys included, on the exposed end.
If you already have a Tool Tube you can order just the Locking End Cap and lock.
Our Tool Tube mounts in place of the little stock tool carrier. The tube is made from 3 1/2" O.D. ABS pipe. It's held by 3 strong powder coated steel straps. Both ends are sealed with waterproof expanding plugs. This is the ideal way to carry those items you always want to have with you on every ride. Tube is approximately 13" long.
You can now order your Tool Tube with a Locking End cap, mini padlock and keys included, on the exposed end.
If you already have a Tool Tube you can order just the Locking End Cap and lock.
Does not fit if your bike is equipped with the new emissions system. The charcoal canister prevents the tool tube from being mounted properly.
Our Tool Tube mounts in place of the little stock tool carrier. The tube is made from 3 1/2" O.D. ABS pipe. It's held by 2 strong powdercoated steel straps. Both ends are sealed with waterproof expanding plugs. This is the ideal way to carry those items you always want to have with you on every ride. Tube is approx 13" long. Long enough to carry your Tire Iron Wrenches.
You can now order your Tool Tube with a Locking End cap, mini padlock and keys included, on the exposed end.
If you already have a Tool Tube you can order just the Locking End Cap and lock.
Rear wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.
Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.
Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.
Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.
Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.
The rubber coated outside diameter creates an optimum seal at the hub.
Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.
| Description | QTY per Kit |
| Ball Bearing | 3 |
A pack of 10 Fuji style lock nuts to put on the sprocket of your KLR650. These are an 8 mm, flanged type nut that will keep your sprocket snug and tight.
