The small size and right angle hose barbs make this filter easier to fit into the small space between your fuel petcock and carburetor. Filter body is only 7/8" diameter. Straight filter is 2" long, 90 degree filter is only 1-5/8" long.
Included in this kit are the parts needed to repair a second generation TK carburetor. You get a new float bowl gasket, needle valve with O-ring, needle, mixture screw, and stock jets for the '01-'26 models kits.
Genuine Keihin spring, washer, and oring for the fuel screw of FCR and FCR MX carbs.
Just the parts…
Fuel screw spring, washer, o-ring (fuel screw not included)
Here's a UNI dual layer foam air filter element for the KLX230. Needs to be treated with air filter oil like any other foam filter.
The perfect complement to our Power Commander V or AutoTune modules, the POD-300 gives you an accurate real-time reading of your vehicle’s vital fuel, engine and air information.
Featuring a robust array of options, you can toggle the display, so the data most important to you is front-and-center. The POD-300 can log channels to internal memory, then access them when you’re done riding through our Power Core software (only available for Windows computers). This display module connects to your Power Commander V/6 or Wideband 2 device network through a CAN cable (included).
The POD-300 is weather-resistant, so it can be used in any environment. The high-contrast display is easily viewable in direct sunlight. It includes a velcro backing for easy installation and removal, or you can purchase a handlebar mount separately.
Please note that the POD-300 is a display module only, which is used in conjunction with Power Commander V, Power Commander 6, AutoTune or Wideband 2.
The map selection switch allows the rider to switch between two different maps "on the fly" within the Power Commander V.
Tried, true and tested the Power Commander continues to evolve with the Power Commander 6. Developed to simplify the user experience, PC6 makes choosing and tuning a map easier for the end user. All the same benefits you have relied on for over 20 years remain to keep you at the front of the pack.
The Power Commander 6 fuel injection tuning device allows you to optimize your fuel and timing curve (where applicable) giving you the confidence to roam freely. With fine tune adjustability and multiple inputs, the Power Commander 6 will keep your vehicle running at its full potential letting you concentrate on the journey ahead.
Featuring a plug-and-play setup, Power Commander 6 can be installed discreetly underneath your seat, cowl, dash or other location ensuring your ride looks as good as it runs. Removing the device reverts your vehicle completely back to stock. With the ability to store and switch between two maps on-the-fly (via the map switch accessory) and connect to various Power Commander accessories such as the Autotune, Quickshifter or POD-300, the Power Commander 6 gives you features and functions that provide you with the ultimate ride.
All PC6 models have an end-user adjustment of +/-15 in the FUEL table and +/- 8 in the timing table (if applicable). This adjustment is on top of the values that are in the BASE map loaded to the device. This BASE map can be any of the available maps from the Dynojet website, or those you may have received from a third party.
The Battery Tender® Junior Selectable is much more than a trickle charger. It has a brain. It's lightweight, compact, and fully automatic; very easy to use, especially in small spaces. It will keep your Lead Acid, AGM or Lithium battery fully charged so that it is ready to go when you are
A motorcycle rectifier-regulator is a crucial part of the charging system, acting as a charging control device to prevent damage to your battery and electrical system. These OEM-style units are direct replacements, providing the proper fit and the expected performance on your bike
Built with the latest in Lithium Ion Polymer Technology. All components are designed, manufactured, assembled and packed in one location assuring high quality and consistency. Besides extreme lightweight (50% to 70% lighter than standard lead-acid batteries) it also features a built-in LED test gauge and the ability to mount it in any position. There is no hazardous acid or heavy metals, it is non-explosive and non-combustible.
The Firepower features Increased cranking amps over lead acid batteries and has a very fast recharge cycle and can be brought up to a 90% charge within 6 minutes and also has 6 to 12 times more cycle life when compared to lead acid batteries. A 2-year warranty insures that your investment is protected.
Rated at 250 CCA (Cold Cranking Amps)
Package Dimensions: 6.20 x 3.70 x 4.80
A set of replacement brake and clutch levers. Standard length.
Please be sure and order the correct levers for your model year KLR.
Note: Gen 1 levers are black
Gen 2 levers are Silver
Zeta Revolver Shift Lever
MAGURA HYMEC – AN EASY TO INSTALL ALTERNATIVE TO A MECHANICAL CLUTCH.
This system replaces the clutch lever and cable – with a small lightweight hydraulic system for improved clutch control. The Hymec ensures an easier operating pressure, a constant pressure point, no more cable adjustment and smooth clutch actuation to ensure the perfect take-off every time. Hymec significantly improves vehicle performance – it allows the user to feel the point where the clutch releases and actuates. This product has been developed over many years and been tested under the toughest conditions possible in the world of motorcycle off-road sport. It has been used by world champion riders who all agree as to the benefits but it is just as useful to the complete novice who stalls at the traffic lights.
These 7/8" bars fit in the stock clamps and raise your grips a couple inches. They look great too!
| Width | Height | Rise |
| 813mm | 160mm | 104mm |
| Clamp Area | Sweep | Control Area |
| 236mm | 100mm | 199mm |
This unique design from Rox allows you to move your bars either closer (1" up and back) or further away (1" forward and 1-1/4" up) depending on rider preference. These risers have an oblong mounting hole so that they will fit virtually any triple clamp with 8mm bolts. A set of reducers lock into the risers ensuring no slippage whether you have a 7/8" or 1-1/8" bars.
Because these are offset there may be limited clearance between the gas tank and the risers when the bars are fully turned on some models, mainly when mounted to move the bars closer.
A high quality replacement clutch cable.
With the split back, you don't need to remove your grip or throttle tube, just put it on and tighten 'er down. Put the mirror in and hit the road. Clean and simple.
One folding mirror. Includes handlebar mount. Can be used on left or right side.
Sold individually.
This new mirror can be folded out of the way when it's time to hit the trails. These are quite similar to the very popular KTM folding mirrors but at half the price.
Fits either left or right side and includes handlebar mount.
Sold individually
Can't see past your shoulders? These mirror extenders will get your mirrors higher and farther out for a much better view of the road behind you.
Genuine Suzuki super moto fender. A perfect match for the original gray plastic.
Left and right stock OEM Suzuki side panels plastic sold as a pair.
Includes one heat shield. Depending on your application and preferences, more than one heat shield may be useful. Extras can be added here.
OEM Suzuki headlight cowling.
High-quality, direct replacement plastic kit includes:
Yellow kit is only available with white side covers
Add-on Headlight cowling fits S and SM models not "E" offroad model
Transform your ride. MadStad's patented mounting system allows riders to adjust the height and angle of their motorcycle windshield resulting in much smoother airflow, better wind protection and a more comfortable ride than any fixed windshield can provide.
What's included and what's not included in the kit:
Their complete drop-in system is custom-made for your bike and includes everything needed to mount and position the shield.
Your bike will not require any modification.
The MadStad adjustable brackets sit out in front of your fairing on black fly screen which attaches in place of the factory shield. With the windshield now separated from the front of the bike and the fly screen helping to deflect wind up from underneath, you have total control over the shield height, angle and airflow. This lets you dial in a smooth ride and quieter cockpit far better than any fixed windshield can provide.
Replace your motorcycle’s windscreen with PUIG’s touring windscreen. Manufactured in acrylic of 3-4 mm according to the motorcycle model to guarantee maximum protection from the wind, improving the aerodynamics of the piece and possible debris that may impact you during your ride.
In addition, it comes with a variable visor that will redirect the wind even more while achieving a great sense of comfort on board your machine. This visor is fixed to the touring windscreen by screws, since the screen comes with the holes already made to facilitate assembly.
The windshield has a rounded contour of> = 2mm, complying with the TÜV regulations.
This part is only available in smoked finish.
For assembly, PUIG provides instructions with mounting tips, so you can quickly enjoy the touring windscreen on your motorcycle.
Reduce exhaust leaks with this new OEM exhaust gasket. This gasket goes between the header pipe and the cylinder head.
We recommend Anti-Seize on exhaust fasteners.
Reduce exhaust leaks with this new exhaust gasket. This gasket goes between the header pipe and the cylinder head.
We recommend Anti-Seize on exhaust fasteners.
Reduce exhaust leaks with this new OEM muffler gasket. This gasket goes between the rear tail/muffler pipe and the header pipe.
No repacking required. The LeoVince X3 Enduro is made with TIG welded stainless steel internals and aluminum outer shell. It features a semi-direct chamber design that is maintenance free. It's quiet too! Our own in-house testing showed a 84dB sound level using the USFS J1287 testing procedure. That is a bit louder than stock but significantly quieter than other aftermarket mufflers. It includes a certified Spark-Arrester. This muffler requires a stock muffler joint gasket when used with either the stock headpipe or the FMF headpipe.
The T-6 exhaust system contains a stainless steel head pipe, brushed aluminum canister and a carbon fiber end-cap for added durability and a professional look. This exhaust system features the same benefits as the T-6 Stainless Steel Exhaust System, but is designed to fit Yamaha's TT-R125 model. In addition to all of these features, the T-6 will come with a removable United States Forest Service approved spark arrestor for trail/off-road riding.
Features Include:
The Modoc 250 replacement rear shock significantly upgrades your Yamaha XT250 suspension. Cogent Dynamics custom build this high quality and high performance shock to suit your riding needs.
Cogent Dynamics build a fully custom suspension component, just for you. To best meet your needs, please spend a few moments providing us with your riding style (off-road / adventure, or street / commuting) and your approximate weight with gear and luggage in the comments during checkout. The information you provide helps them setup your suspension to most closely meet your needs.
Specifications for the Modoc 250:
Don't want to buy a new shock? This rebuild makes the stock shock about 10 times better. Cogent Dynamics takes a stock DR650 shock, tears it down, cleans it up, adds a hard ceramic coating, then rebuilds it with a completely new Shock Shaft Assembly with rebound damping adjustment.
Any aftermarket spring for your stock shock will fit on this shock. If you are currently using the original spring, you will want to order a stiffer spring to go with your new shock.
Our 7.5 kg/mm rear spring is 16% stiffer than the stock one and is perfect for the majority of riders. If you are a larger rider, or carry a lot of gear or a passenger (total weight exceeding 250 pounds) you will probably want the 8.3 kg/mm rear spring which is 28% stiffer than stock.
This shock includes the Bling Ring preload adjusting ring AND the Thrust Bearing! This replaces the two stock preload/lock rings. This ring is CNC machined aluminum with the additional thickness to provide superior support on the shock body.
Low shock also available. This option will lower your seat height 1" without the need for lowering links. All other features of this shock are the same as the stock height.
This option is ideal for those who desire the least amount of down time to install this suspension upgrade.
This kit includes a core charge that allows us to ship your new shock before we receive your stock shock core in 'good' condition. More details regarding core exchange linked below.
Low friction 'triple lip' seal design. Oil seals last 3-4 times longer that OEM seals. Kit includes fork seals and dust wipers.
Billet aluminum lowering links. Lowers the rear suspension approximately 1 to 2 inches depending on application.
*Important when lowering the rear suspension you want to raise the fork tubes in the clamps an equal amount of inches that the rear is being lowered. That way your bike will sit level when done.
Note: We only recommend the 2" lowering links for lighter non-aggressive riders as they allow the tire to rub when near bottoming.
Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.
Some KLR models from 2004 - 2007 may have a longer shank that do not allow the bolts to tighten to the bearing. If that is the case, we recommend the addition of either a 14 mm split type lock washer or a 15 mm flat washer under the nut of both link mounting bolts.
These springs are custom wound specifically for the Kawasaki KLX's. Stiffer than the stock springs, these will make your front perform significantly better.
Carbon Graphite "X" Brake Shoes
Sintered Pads from EBC provide great performance in all conditions yet still give you long pad life. Front pads are double H rated for maximum breaking. Rear shoes offer maximum durability and excellent braking performance.
Sintered Pads are best for regular riding. Long life, and good performance in all conditions
Note: The Honda XL750 Transalp has dual front rotors, two sets of pads are required.
This frame includes six, white, full-spectrum LED bulbs on a 6-inch strip for bright illumination of your license plate. It is made in a sturdy cast aluminum, and is powder coated with a durable black finish.
Outside frame dimensions are 7.25" in. wide by 4.2". Center to center mounting hole distance is 5.7 in. All mounting hardware is included.
Includes all wheel bearings, new dust seals. The rear kit includes the bearing and seal for the cush drive hub (sprocket carrier). All bearings are sealed on both sides.
Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.
Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.
Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.
Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.
Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.
The rubber coated outside diameter creates an optimum seal at the hub.
Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.
| Description | QTY per Kit |
| Ball Bearing | 3 |
| Seal | 2 |
Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.
Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.
Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.
Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.
Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.
The rubber coated outside diameter creates an optimum seal at the hub.
Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.
| Description | QTY per Kit |
| Ball Bearing | 3 |
| Seal | 2 |
Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.
Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.
Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.
Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.
Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.
The rubber coated outside diameter creates an optimum seal at the hub.
Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.
| Description | QTY per Kit |
| Ball Bearing | 2 |
| Seal | 2 |
Steel wheel weights replace the old lead ones that are no longer legal in some states. Mount up new tires and make sure they are balanced for a smoother ride and longer tire life.
This is a 60 piece pack, 1/4 oz. weights with adhesive backing.
Protect your wheels from scratches and dings caused by tire changing tools.
Changing tubes or tires without the right tools can be a real chore. Don't fight your snug beads any longer, use this 27" long tool that opens to 7-3/4" to provide the leverage you need to easily break your tire bead. Constructed from heavy-duty steel with comfortable no-slip grips, this tool makes the job a snap.
A replacement Clarke Gas Cap that fits most Clarke Gas tanks. Comes with rubber gasket.
You want a lighter replacement for your heavy steel stock tank? Don't need the extended range (or bulk) of the big Acerbis or Clarke tank? The 4.0 gallon tank from IMS might be just right. Includes cap, uses stock petcock.
Simple, lightweight rack made from rugged 1/8" 5052 Aluminum, with a rigid 5-point mounting system.
Low profile allows for easy seat removal.
Features:
Note: Placement of this top rack does require removal of the stock tool bag.
Their rear racks are great for adding the extra storage needed for your next adventure. They are the perfect size for a backpack or small duffel bag. Their steel racks are built to handle any riding style you throw at them, now Rotopax ready! This is the ENDURO Series KLX250S/SF rear rack which measures 10 inches wide and 12 inches long.
Easy to Install
Their rear racks are great for adding the extra storage needed for your next adventure. They are the perfect size for a backpack or small duffel bag. Their steel racks are built to handle any riding style you throw at them, now Rotopax ready! This is the ENDURO Series DRZ400S/KLX400S rear rack which measures 10 inches wide and 12 inches long.
Easy to Install
A durable, lightweight option for your TW200 when transporting flexible luggage on the trail.
A collection of waterproof bags made by industry giant Givi. There are five different bags available, a 30, 20, 40 and 80 liter waterproof roll top bags and then a 20 liter back pack with padded straps and padded back.
Waterproof Cargo bag, 80 lt. Aimed at road Enduro bikes and Touring bikes
Materials: • Heavy-Duty Tarpaulin/PVC • IP 66 water resistance: resistant to heavy rain, temporary immersion and extreme conditions Other characteristics: • Reflective print for greater visibility • Waterproof roll-up closure system • Additional internal zipped pocket • Adjustable EVA-padded shoulder strap • Air vent valve • Elastic straps for universal mounting
Round The World Panniers™ offer a flexible, impact-resistant, and waterproof alternative to a large touring hard pannier set — giving you every bit as much packable volume and convenience without the extra weight and bulk of hard boxes. The largest capacity pannier in their product line, Round The World Panniers, offer 90 liters of packable volume that’s ideal for everything from a weekend of motocamping to long-haul adventure motorcycle travels. They are also great for riding with two people and carrying their gear.
Roll top with durable side-release buckles for secure closure and load stability.
Included set of two seam-sealed waterproof inner liner Dry Pods™ keep gear dry and organized.
Pair Round The World Panniers with GL Pannier Mounts for the ultimate in lockable, quick-mount, quick-release convenience.
Giant Loop Rubber Boa Straps confidently put the squeeze on a spare inner tube, tools, water, or other off-road essentials when strapped to dirt bike fenders. Stretch elastic shock cord with heavy-duty injection molded fender hooks. A simple locking slot applies dynamic tension to create a dead-solid connection between plastic fenders and relatively small, lightweight gear—even in demanding terrain.
For reference, the stock gearing for the WR250R is 13/43 while the X model runs with a 13/42 stock configuration because of the SM wheels/tires. Both use a 108 link chain with the stock gearing.
The JT rear sprockets listed are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.
Limited availability on Aluminum from PBI. Manufactured from aircraft 7075 T651 Plate Aluminum.
If you want the additional low-end grunt that the 46, 48 or 50 tooth rear sprocket will give you, you will need longer chain as well.
New Rear Sprockets require new Sprocket Bolts because of a difference in the holes vs. the stock bolts.
High-quality DID chain and steel sprockets for 2002 & later TTR125s.
The chain slider protects the swingarm from contact with the chain. Replace yours before it wears through to the swingarm.
Barnett high performance clutch kit includes drive plates, carbon fiber friction plates, and heavy duty springs.
RadiusX is a high performance centrifugal auto clutch combining our TorqDrive and EXP technologies. TorqDrive provides more clutch disks in less space, allowing for maximum performance within your bike’s existing clutch footprint. You retain full control of shifting and use of your clutch lever with no compromise in power delivery.
Features:
High quality clutch cover gasket. If you are servicing your clutch, a new gasket will prevent oil leaks.
Replacing your clutch or removing that side cover for any reason? You are going to need a new gasket for the cover to ensure a leak-free assembly.
Includes all necessary top quality gaskets, and seals for engine rebuilds.
GoldPlug is the gold standard in engine protection.
Stainless steel drain plug with an extremely strong magnet that picks up metal flakes in your oil.
12mm Thread, 17mm Head.
Replacement handguards for your Acerbis set up. Tough Polypropylene shields with a larger 6" outer diameter, built for extreme riding conditions.
Features:
From JNS Engineering, a super solid Rear Master Cylinder Guard for the XT250, WR250R and X. CNC formed and then powdercoated black for lost lasting corrosion protection. Did we mention how good it looks? All hardware provided.
The high rigid and light weight design, provides better control of the rear brake. Clevis body is made of A7009-T6 aluminum. Comes with a specially designed stainless steel pin.
With this upgrade, you can avoid having to keep new replacement cotter pins on hand every time you adjust your chain.
The Phillips type screws used in Japanese motorcycles are actually Japanese Industrial Standard (JIS) screws are very easy to strip if you are using a regular Phillips screwdriver.
Maintain your chain or sprocket, even change your rear tire or wheel while out on the road without the need for a center stand, with the BikeMaster Liftstick. Handy and convenient to carry. Perfect for street, dual sport and trail use. Liftstick includes non-slip rubber boots, which protect your motorcycle's swingarm from any scratches while claws at the base provide traction and stability during use.
This USB device connects to a battery cable with an SAE connector just like the typical Battery Tender outlet, and allows you to charge your electronic devices. Input is 12 Volts, with an output to the USB port of 2.1A maximum, perfect for your phone or other USB devices.
Special tool to remove the flywheel from the end of the crankshaft.
Renthal chain lube is 100% lubricant, zero propellant. So this new 250ml bottle size combines high performance and value.
The all-new formula Chain Lube is specially designed to penetrate all parts of the chain. This all-condition lube is compatible with all o-ring and non o-ring chains.
A somewhat neutral cross-sectional shape for improved handling and stability for light weight supermoto bikes.
Improved wet and dry performance.
Tubeless and H rated (max speed of 130 mph)
These footpeg heads are bike model specific and are required to install Puig footpegs to your bike.
The IMS Super Stock pegs are the perfect choice for both the daily commuter and the rider-in-training. Their mellow tooth design keeps you planted while preventing wear on your soles. They are also perfect for young riders who don't need or want a more aggressive option.
Wider foot pegs for sure-footed comfort.
17-4 cast stainless steel.
| Width | 1.97" |
| Length | 3.18" |
Headlight is DOT approved. Has both high and low beams. Attaches to the upper fork tubes with rubber straps. Turn signals are embedded in the headlight housing.
Integrated turn signals may require resistors to flash correctly.
Now a lifetime warrantied LED light set at a budget friendly price.
The new Cyclops Pegasus led light set comes complete with a high quality relayed wire harness and a potent combo light beam pattern.
We are able to offer this fantastic light at a great price due to a one piece optic and sealed beam construction, eliminating extra parts and creating a very durable and high performance light.
These lights in white feature 7 watt emitters (28 watts per light) with two 10 degree and two 25 degree optics, Good for 500 plus ft of lighting (white).
The amber version is a Cree 3 watt emitters (12 watts per light).
This combo beam pattern offers good forward lighting and extremely good conspicuity.
The light set is available in white 5600K or a extremely bright Amber, perfect to allow those autos to see you. Lightweight and robust at 2.75 inches with a single stud mounting, they fit just about anywhere you would like to mount your lights.
Specs:
Easily turn your blinkers into additional running lights and brake lights (rear) for added visibility.
White light in the front and red in the rear. Rear red running lights and bright red brake lights. You can omit the running and brake lights if you wish and still have the best blinkers on the market.
Dazzling bright Amber blinker functions.
All in a spring-loaded stock to prevent damage from a tip over, crash or impact with brush, trees etc. They will bend 360 degrees, but are stiff, durable and nearly unbreakable.
Suzuki DR650 Specific plug and play kit using factory connectors, flasher and diode kit included.
The SignalMinder unit is designed as a plug-in accessory for many Japanese bikes. SignalMinder uses a microprocessor to cancel the turn signals at one of three selectable time outs; 10, 20 or 30 seconds.
You can also make it so that all four of your signal lights also act as running lights and establish a dual-channel system on your bike. With the dual-channel system, when you activate the RIGHT turn signal three times in succession, you get 4-way hazard flash lights.
Connecting the 12 volt supply from the brakes to the SignalMinder, also allows for a brake flash option.
There are many options and configurations using this electronic tool.
No wire cutting required. The kit includes Scotchlok connectors to tap into existing wires.
Replacement retaining pins for the brake caliper. Includes 2 stock style brake pins.
Be sure to use some anti-seize on the threads when you install them.
Rear caliper only for DR350 and DR650.
This plug-n-play kit includes sealed LED headlight assembly and adjustable mounting brackets specifically designed for the 2008-2018 Yamaha XT250. The new design for the black headlight produces more light and has much more uniform beam pattern when compared to the previous version. New design currently only available in black, chrome may be available in the near future. No wiring, soldering, resistors, trimming, drilling, or fabrication required.
