Search Products

Extra protection for your motor! Strong magnet at the end of the plug picks up metallic flakes in your oil, protecting your engine!

Complete kit to replace the bearings and seals in the DR350 shock linkage. Includes the lower shock bearing.

• Seal profile is engineered to create equal pressure in each seal lip; equalized seal pressure creates less drag and longer seal life
• Patented MAX-LIFE has a coefficient of friction up to 3 times less than the OEM seal material
• Triple-lip seal design
• Dyno-tested to last 3 to 4 times longer than OEM seals
• Directional ribs allow seal to be installed easily
• Kit includes fork seals and dust wipers

Low friction 'triple lip' seal design. Oil seals last 3-4 times longer that OEM seals. Kit includes 2 Fork Seals and 2 Dust Wipers.

 The perfect option for the DIY'er.

The Cogent Dynamics Shock Shaft Assembly is ready for installation. The Cogent shock shaft also features an external rebound damping adjustment. Just what you need to have the ultimate in rear suspension control.

Does not include a spring. Compatible with both stock and aftermarket springs.

Requires 5wt shock oil

These Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. These units have been given the seal of approval by the ProCycle staff for both performance and ease of installation. No disassembly of your forks, no drilling of damper rods. Just change the oil over to 5w and install the DDCs under the springs and hit the trails.

DDC Tool will not work with this spring series

These Cogent Dynamic Drop-in Cartridges will vastly improve both the compression and rebound damping of your stock forks. These units have been given the seal of approval by the ProCycle staff for both performance and ease of installation. No disassembly of your forks, no drilling of damper rods. Just change the oil over to 5w and install the DDCs under the springs and hit the trails.

These Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. These units have been given the seal of approval by the ProCycle staff for both performance and ease of installation. No disassembly of your forks, no drilling of damper rods. Just change the oil over to 5w and install the DDCs under the springs and hit the trails.

DDC Tool will not work with this spring series

These Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. No disassembly of your forks, no drilling of damper rods. Just change the oil to 5w and install the DDCs under the springs and hit the trails.

Stiffer fork springs are required to realize the full benefits of the DDCs. Please call if you have any further questions.

The DDCs are not recommended for use with progressive springs.

The DDC Install/Removal Tool which makes installation that much easier.

These Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. These units have been given the seal of approval by the ProCycle staff for both performance and ease of installation. No disassembly of your forks, no drilling of damper rods. Just change the oil over to 5w and install the DDCs under the springs and hit the trails.

Stiffer fork springs are recommended to get the full potential of the DDCs.

These Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. No disassembly of your forks, no drilling of damper rods. Just change the oil to 5w and install the DDCs under the springs and hit the trails.

Stiffer fork springs are required to realize the full benefits of the DDCs. Please call if you have any further questions.

The DDCs are not recommended for use with progressive springs.

Add the DDC Install/Removal Tool which makes installation much easier.

The Cogent Dynamics DDC valves are the most cost-effective upgrade you can make to your motorcycle’s forks. Unique and the first of its kind, a DDC kit is available to upgrade many motorcycles that are originally equipped with simple damper rod type forks as front suspension.

We do recommend stiffer than stock front springs to bring the full potential of the DDCs out. OEM springs are dual rate 0.45/0.55 kg.

A CNC machined fork brace to stiffen up the notoriously wimpy front end on the DR. Have more confidence in your front end on or off the pavement.

Split design means that installation takes minutes without having to remove the forks. Available in a black anodized finish.

Top End Gasket Set is designed for a piston replacement job and includes:

• Head Gasket
• Base Gasket
• Intake Gasket
• Exhaust Gasket

Rebuilding your engine? Here is a complete gasket kit for your TW200. Includes: Head Gasket, Base Gasket, Stud Gasket, Head Side Cover O-Ring, two Valve Cover O-Rings, Base O-Ring, Stud O-Ring, Rocker Shaft O-Ring, two Cam Chain Tensioner O-Rings, Intake Manifold O-Ring, two Valve Stem Seals, Exhaust Gasket, Left and Right Side Cover Gaskets, Pump Cover Gasket, TDC Plug O-Ring, Crankshaft Nut Plug O-Ring, and Oil Filler Plug O-Ring.

Heavy-Duty clutch springs

• 15% stiffer than original
• Minimize clutch slip
• Reduce plate wear
• Improve power to ground

This is all you need to not only change your oil, but protect your motor as well. We include a magnetic drain plug, to help catch stray metal pieces, a 5-pack of oil filters, and new O-Rings to replace any you have that may be leaking or worn.

• Magnetic Drain Plug
• O-Ring Kit
• 5-Pack of Oil Filters

This is all you need to not only change your oil, but protect your motor as well. We include a magnetic drain plug, to help catch stray metal pieces, a 5-pack of oil filters, and new O-Rings to replace any you have that may be leaking or worn.

• Magnetic Drain Plug
• O-Ring Kit
• 5-Pack of Oil Filters

Providing unbeatable performance and exceptional value, Hiflofiltro is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide. The filters are also supplied to original equipment manufacturers as well as private label brands.

Warp 9 CNC billet machined Oil Filler Cap. 

Available in Blue or Black and it includes a new O-ring

To make removal as easy as possible, the center tab takes a 12mm wrench perfectly, or a 1/4" ratchet drive in the center. 

On each end of the center tab is a drilled hole should you find it necessary to safety wire your filler cap in place.
 

Billet plugs for your left side case. 

Includes both the timing mark plug and the crankshaft access plug.
 

• Includes aluminum cylinder, piston kit, and special gasket set designed for larger water jackets
• Bolts on with no machining required
• 94mm big bore piston
• Aluminum cylinder designed with wider water jackets for better cooling.
• Forged hi-compression piston  12.8:1
• Includes all necessary Rings, Clips, and Gaskets.

This kit provides much of the performance gain of the more expensive 150 (143cc) kits. But gives better reliability due to the thicker wall of the cylinder sleeve.

• Wiseco 55mm high compression 11:1 piston, rings, wrist pin, and clips
• HotCams stage 1 performance camshaft
• Includes top end gasket set
• Requires cylinder to be bored to fit the larger piston

• Bolts are CNC-machined from high-quality aluminum
• Embedded magnet helps keep bolt in place
• Pre-drilled holes make for easy installation of safety wires

Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula is plush, while still offering the necessary amount of support. Their unique comfort and shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.

These great features combine to offer you a custom seat feel, and provide greater enjoyment and increased range for long commutes, or Dual-Sport rides!

The Complete Seats come assembled with an high quality aftermarket pan and ready to ride.

Fits Model/Years:
2022-24 KLR650, S, ABS, TRAVELER, ADVENTURE

State-of-the-art replacement seats, Sargent seats are built on a percision-molded lightweight Polytec seat pan. Sargent's proprietary seat foam (Super Cell Atomic Foam) is their own unique blend of resilience, firmness, and vibration-absorption qualities, making it well suited for long distance comfort and support. Sargent seats are covered in a marine-grade, UV-stablized mildew resistant CarbonFX vinyl. Available in standard height and 1" lower than stock. These seats will fit bikes with the stock, IMS, or any other aftermarket fuel tank.

From our friends at JNS Engineering, a very nice mount for a set of auxiliary lights on the front of your KLR650. Laser cut from 0.190" 5052 aluminum it is CNC formed and then powdercoated black. One of the best benefits is that it will not interfere with even the largest aftermarket fuel tanks. All included mounting hardware is stainless steel.

There is a lot of technology packed into this tail light/fender eliminator kit. You have programmable turn signals and Safety Brake Pulsing both built into this product.

You can enable or disable the safety brake pulsing feature.
This kit includes only the highest quality components, including the pre-installed 12oClockLabs processor board, which is made in the USA.

• Plug and Play
• 7 Different Programmable Turn Signal Patterns (for demo video click here)
• Safety Brake pulsing built in (Can Enable or Disable)
• Superbright LED's; For excellent brightness, even in direct sunlight
• License Plate Light built in
• License Plate Bracket fits the common USA license plates, sloted for maximum plate compatibility.
• Includes Mounting Hardware
• Saves about 2 lbs over the factory tail light setup
• Made In the USA

We recommend a "Fixed Rate Flasher" unit for use with this kit. When you install aftermarket signals it changes the load on a factory signal system.

This kit does not include parts to mount aftermarket turn signals. The pre-installed processor board allows the turn signals to be integrated in to the tail light.

The Edge-2 Tail Light and License Plate Holder is a simple bolt-on replacement for the stock unit. Included is an aluminum mount for the light and license plate that is model specific. The light unit uses 16 high-intensity red LED's for tail/stop light function. 3 white LED's are used for license plate illumination. Included is a set of turn signal brackets that bolt to the mount. These are designed for a small signal with a 8mm mounting stud. 

• Eliminates the need to cut and splice wiring when using aftermarket turn signals or marker lights
• Plug into the OEM turn signal plug and then use bullet style connectors used on aftermarket lights
• To verify proper fitment, compare connector photos to OEM connector
• Sold in pairs

Taillight and brake light Attaches to the top of the rear fender. Dimensions: 3 1/2" wide x 2" long x 3/4" tall. D.O.T. approved.

RotoPax holder made to mount a single Fuel and/or Water container.

Need to mount two containers? A water and a fuel? Two waters? Get the extender which allows you to stack two containers no problem! Single mount, two containers

Made from strong and light 5052 aluminum to hold your license plate firm and up, out of the way for maximum tire clearance, prefect for your new dual sport bike.

It uses the original tag light with out any modifications to your bike. Mounting hardware and instructions included.

The Rally windscreen from Parabellum is the perfect protection from wind and debris without sacrificing technical off-road capabilities. This is an upright rally type windscreen that looks aggressive and performs well under all types of riding. Designed primarily for the off-road / dualsport enthusiast, this shield keeps pressure off the rider's chest while commuting from home to adventure and back.

Mounting is accomplished by drilling two holes on each side of your headlight cowl using the provided template. The shield is 14 inches tall, 11.5 inches wide at the bottom narrowing to 8.5 inches at the top. Made from military aircraft grade cast acrylic.

This unit will not fit properly on '90 to '01 DR650 headlight cowls.

For straight 7/8" handlebar

Protect your hands and levers with the Barkbusters Storm lever and weather protection handguards. Full wrap solid heat treated aluminum bars with secure two point mounts on each side provide strength while attractive and generous guards provide shelter from the wind and weather. Ride longer with the Storm handguards and complete mounting kit by Barkbusters.

Features:

• Two mounting points provide secure protection
• Full wrap guards
• Heat treated aluminum backbone bars
• Easy installation
• Tough and weather shielding Storm handguards
• Aluminum backbones are compatible with all Barkbusters deflector guards

What's in the box:

• Left and right aluminum backbone bars
• Inner and outer handlebar mounting hardware for both sides
• Left and right Storm plastic handguard deflectors
• Installation instructions

Not recommended for Africa Twin, T7, Himalayan, or V-Strom. Please see specific listings for those models.

Replacement handguards for your Cycra set up. Injection-molded high-impact plastic replacements. Includes all hardware needed for mounting.

You can keep your Cycra handguards even if you upgrade your handlebars to a different width.  

Replacement mounts that keep your Cycra handguards fresh and tight.

CNC-machined from billet aluminum for the best fit and strength.

Please Note: These handguards do not fit the Yamaha T7

Mount Barkbusters standard aluminum bar handguards to 1-1/8" motorcycle handlebars with the Barkbusters Tapered handlebar saddle clamp set.

What's in the box:

• 4 peice saddle clamp set
• 2 complete saddles

These are all you need to mount your current Barkbusters Handguards when you upgrade to a tapered oversized 1 1/8" handlebar.

Closed handguard with aluminum bar and bracelets.

Ultra-durable closed handguard designed for those seeking greater protection while competing or riding in enduro, hard-enduro and cross-country racing.

Equipped with a 35 mm "C" section anticorodal bar. Provides 5 times more resistance than the classic handguard with an aluminum bar.

The cuffs, oversized with a thickness of 19 mm, guarantee greater strength and increased torsional capacity.

Expanders made entirely of steel.

Cover is impact resistant; wide area protects the pilot's hands more, while flexible lower area absorbs any accidental contact with the knee.

Mounting kit included.  Mounts to all off-road competition bikes (motocross and enduro) with inner size from 13.5-16 mm and outer size from 22-28 mm.  Works with 7/8" or 1-1/8" bars.

Co-molded logo.

T-Rex Racing skid plate for the Suzuki DR650, designed to protect your bike from dirt, mud, and other debris.

Made from precision CNC machined aircraft grade aluminum finished with black powder coating for durability. Rest assured that you are getting the best material commercially available.

Specifically designed to work with T-Rex Racing engine guards, and center stand.

Will not fit properly with oversized head pipes.

You want a lighter replacement for your heavy steel stock tank? Don't need the extended range (or bulk) of a big tank? The 3.7 gallon tank from Clarke might be just right. It's almost 5 lbs lighter and holds close to 1/2 gallon more fuel than stock to increase your range by about 20 miles. Fits with your stock petcock, Pingel or Raptor petcock.

Get better range from your DR650 by adding an IMS 4.9 gallon fuel tank. Available in Natural, White, Black and Blue. Natural color is recommended if you wish to easily see the fuel level in the tank. Includes cap and fuel petcock.

More range at a great price. Choose  the 2.7 gallon tank for the KLX250S in Black, Green, Natural or White.

  This tank will NOT fit the 2009-2015 models.

Acerbis 5.3 gal tank adds function and great looks to your DR650. This high capacity fuel tank incorporates modern lines and high quality construction that can't be beat. Includes gas cap, petcock and all mounting hardware.

  Installation of the Acerbis tank requires relocation of the front turn signals. Otherwise the stock signals will contact the tank at full lock. Our Turn Signal Relocation Brackets Move the front turn signals up and forward to clear the bigger tank.

Warp 9 stem puller

 Here is a list of the features of their CNC machined tool.

• Stainless Steel tip, wont break like softer brass tip
• Ribbed head for easier core removal
• Core tip threads into handle to protect tip from damage
• Includes spare valve core in handle for easy trail side repairs
• Tapered handle ends to make tip removal easier with gloved hands and non square edge doesn’t damage tool bags

Motion Pro T-6 Combo Lever has a hex box wrench for your axle nut on one side and a perfectly contoured tire spoon on the other. Manaufactured from lightweight forged T-6 aluminum with a hard anodized finish. These beauties are just under 10 inches long and weigh only 3.5 oz. Available in a 12/13 combo unit and a 22, 24, 27 and 32mm hex ends.

• Complete kit from Moose Racing to rebuild the OEM carburetor
• Each kit contains all necessary gaskets, O-rings, float valve and jets
• Supplied to Moose Racing by the same supplier the OEMs use

• Designed to fit in the factory air box exactly like original filter
• The best selling replacement air filter for competition motorcycles and ATVs
• Unique two stage design allows for easy and complete cleaning
• Dual layer of foam, can be serviced separately
• Thin Ultra Seal base is virtually impossible to tear and has a built-in "Grease Groove"

For mildly tuned machines using the stock airbox, with stock or K&N filter. May also be used with a good aftermarket exhaust system

• Provides a simple and affordable solution to carburetor tuning problems.
• Allows you to tune your bike for increased power and smoothness while retaining fuel economy.
• Includes a guide booklet on how to install and use your jet kit to it's full potential.
• For a top quality installation we recommend adding an extended fuel screw and a set of replacement carb screws.

Quality steel sprockets and 525 O-Ring chain. 525 chains come in 120 link length and will have to be cut down to fit. They also come with rivet type master links. Clip type master links are available below. Single sprockets and chains are also available below.

We have 44, 45, 46 and 47 tooth rear sprockets available for the SV. Select the sprocket size from the dropdown.

• Computer-designed to achieve ultimate strength at minimum weight
• JT combines leading-edge technology with top materials to produce the ultimate quality sprocket range with unbeatable value
• Every sprocket meets or exceeds the highest possible quality standards set for the motorcycle industry
• Sprockets are heat-treated and bead-blasted to reduce material surface tension
• Unless noted, rear sprockets made with top-quality-grade C45 high-carbon steel

These quality JT sprockets are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.

Rear Sprocket

Note: 2002 and later models have a 10mm sprocket bolts. 2000-2001 models have 8mm sprocket bolts.

For all years.

• Machined from impact and wear resistant chromoly steel
• Heat treated, then finished with a nickel coating for corrosion resistance

A CNC machined chain guide for the DR. Stronger than the wimpy stock unit and can easily accommodate the stock 525 chain as well as a 46 tooth rear sprocket (by moving the lower rub block to the forward position). The rub blocks are also a higher grade, longer lasting material.

• Reduce the friction dragging down your drivetrain
• Polyurethane roller with 98A durometer hardness for long life
• Precision contact sealed bearings keep water and dirt away

High Quality chain. You'll need to cut to fit your sprocket combination.

High-quality DID chain and steel sprockets for 2002 & later TTR125s.

• 13T front sprocket
• 49T or 54T rear sprocket
• 130-link DID chain (must be cut to correct length)
• Note: 2002 and later models have 10mm sprocket bolts.

Handlebar mounts that replace your stock clamps.

These raise your handlebars 1 inch.

Choose 7/8" for standard handlebars or 1-1/8" to allow installation of your choice of oversize/ tapered handlebars.

The Warp 9 shift lever is black anodized and the Warp 9 logo is laser etched into the finish. The black anodized knurled aluminum tip is folding and returns via a stainless-steel return spring. Includes the pinch bolt as well.

The tip is replaceable in the event of damage.

The Warp 9 shift lever is 7075T6 CNC arm, the Warp 9 logo is laser etched into the finish. 

Includes a black folding aluminum tip and stainless spring and pivot pin for years of rust free use.

1" longer than stock

• Warp 9 Flex Levers are machined Billet, anodized and hinged brake levers with CNC machined master cylinder interfaces
• Adjustable reach allows customization to the rider’s hand size
• Double hinge design allows lever to flex out of the way in most impact situations
• Pushrod or Bearing contact styles for smooth brake modulation
• Titanium Pivot / Black levers with laser-etched Warp 9 logo CNC Billet Brake pedal

Fit Disc Brake Models Only

The Warp 9 "3-Finger" Lever Exclusive to ProCycle.  You asked for 3-finger levers, and we had Warp 9 make them for us. Brake lever includes a nice billet clamp with nylon sleeve to allow the assembly to rotate on impact. Will not fit with the stock OEM wind deflectors.

• Warp 9 Flex Levers are machined Billet, anodized and hinged brake levers with CNC machined master cylinder interfaces
• Adjustable reach allows customization to the rider's hand size
• Double hinge design allows lever to flex out of the way in most impact situations
• Pushrod or Bearing contact styles for smooth brake modulation
• Titanium Pivot / Black levers with laser-etched Warp 9 logo

Will not engage the clutch switch on 2010 and later models

Warp 9 Flex 3-Finger Levers are machined Billet, anodized and hinged levers with CNC machined master cylinder interfaces.

Adjustable reach allows customization to the rider's hand size.

Double hinge design allows lever to flex out of the way in most impact situations.

Pushrod or Bearing contact styles for smooth modulation.

New from Twin Air, a forged aluminum KLR650 folding shift lever with your choice of Black, Blue, or Green tip. These are 3/4" longer than the stock lever which makes for easier shifting while standing, as well as for those with a larger boot size.

A set of replacement brake and clutch levers. Standard length.

Please be sure and order the correct levers for your model year KLR.

Note: Gen 1 levers are black
Gen 2 levers are Silver

OEM Style aftermarket replacement brake and clutch levers. Standard length. 

Available as a set or individual.

Please notice that this set is for '90-'09 DR650.

Replaces all 2 bolt style clutch/brake lever mount clamps. Can help save space on short bend handlebars.

Quality replacement clutch cable.

• Nylon-lined housings and precise OEM component dimensions

• Replace OEM throttle sleeves
• Heavier duty and exceed the quality and durability of OEM sleeves
• Will not scar bars like aluminum sleeves
• Nylon fabric composite material
• Molded ridges to help secure grips
• One-piece tube and reel design
• Actual color may vary

The FMF Powerbomb is a four stroke header pipe unit that has a unique bulge precisely located in the header system. A "pre-muffler" of sorts, the Power Bomb actually lowers sound output because it creates more surface area to absorb the sound medium (exhaust). The surface area of the perforated core lets the sound exit into the absorbing material (steel wool packing) and then allows the air to expand, cool and ramp back up with the higher pressure air. The result? The FMF Powerbomb is instrumental in reducing the decibel level on any four stroke and because of the expansion and contraction on exhaust through the system, the flow has been increased by nearly 10%. That means more power throughout the range.

Features:

• Tuned for bottom to mid performance
• Powerbomb headers are the front runner in performance headers
• Designed for full service access to oil filter

The RS-2 is a potent and versatile design that evolved from their original TRC, engineered to provide increased power delivery. With a different pyramidal shape that features increased volume, the RS-2 is a quieter system with a larger core — and it offers the added bonus of outstanding performance in a value-priced package.

• Diamond-shaped sleeve
• Large core and increased muffler packing volume means quieter operation
• Stainless steel cone end-cap
• Stainless steel tail-pipe
• USFS Approved spark arrester included
• 6.8 lbs lighter than stock

We recommend Anti-Seize on exhaust fasteners

ULTIMATE SPROCKET WRENCH KIT

• 12” long wrench gives you more torque to get those thread locked sprocket bolts off easily
• Double ended 12mm & 13mm to fit all modern motocross, Enduro and dual sport bikes
• Dog leg wrench design allows wrench to easily clear rim edge and wide tires
• 8mm allen fits most Japanese bikes 8” long for extra leverage
• Torx T45 fits late model KTM and Husqvarna bikes, 8” long for extra leverage
• Vinyl coated handles to protect rim edge and give a non slip grip
• Makes routine sprocket bolt maintenance a quick and easy job

The plastic fitting that secures the stock choke cable to the carburetor is delicate and easily broken. A broken fitting can cause hard to solve idling and running problems.

CNC machined from billet aluminum and anodized black or blue. If you want to retain your handlebar mounted choke this may be the solution.

  These no longer fit the new version of the ProCycle Remote Choke Cable. Will not work with the long or short reach choke knobs.

• Stop your expensive helmet from falling and hitting the ground while you’re out riding
• The perfect solution to easily store your helmet with your bike.
• 7075 T6 machined aluminum
• Fits all 7/8 handle bars
• Includes 2 stainless screws
• Fits virtually all bikes and makes ( except Harley )

Organic brake pads contain man-made high-performance fibers that are used for their light weight, high strength abrasion resistance and thermal stability. These Aramid fibers have a high strength-to-weight, thermal stability and abrasion resistance to provide advantages over steel fiber-based products. They provide excellent stopping power without noise and rotor galling but still provide fingertip control and strong, predictable brake response.

Double-H sintered metal brake pads feature the HH friction rating, the highest in the industry. These pads provide maximum brake effect and last twice as long as organic pads.

Semi-sintered pads have an all new recipe containing 30% copper by weight with an organic matrix. This design combines the long life of a sintered pad with the great feel and lack of rotor damage common with full-sintered pads. These can be used to replace Kevlar or sintered metal compound pads.

Set includes pads for both front calipers.

Galfer USA produces several different brake pad compounds for all types of riding styles and uses. With over 60 years of friction material production and research, they have learned that one compound doesn’t always do the trick across the board. If you are just looking for an OEM brake pad replacement or a high performance race brake pad, they have you covered!

Set includes front and rear brake pads.

Replace those worn out brake pads with quality EBC replacements.

• The perfect brake pads for leisure use
• Offer maximum durability and excellent braking performance
• Constructed of U.S.-made sintered bronze for longest lifetime
• Best for riding in water, mud, dust, or sand

Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.

The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.

• Significantly improves response and feel over factory rubber lines
• Largest performance improvement for your money over any other braking upgrade
• Stainless steel hose resists abrasion and puncture
• Teflon core does not degrade over time like rubber lines
• PTFE Dupont 64 Teflon® hose
• Feature a heavy-duty stiffener sleeve and route just like the factory lines
• Proprietary, premium fittings
• Banjos utilizes a unique machined channel and sealing surface for leak-free installations
• R&D and engineered in the USA
• GBrakes USA controls the manufacturing process, ensuring the highest level of quality control

Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.

The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.

• Significantly improves response and feel over factory rubber lines
• Largest performance improvement for your money over any other braking upgrade
• Stainless steel hose resists abrasion and puncture
• Teflon core does not degrade over time like rubber lines
• PTFE Dupont 64 Teflon® hose
• Feature a heavy-duty stiffener sleeve and route just like the factory lines
• Proprietary, premium fittings
• Banjos utilizes a unique machined channel and sealing surface for leak-free installations
• R&D and engineered in the USA
• GBrakes USA controls the manufacturing process, ensuring the highest level of quality control

Quality components at a great price.

• Standard Kit: Includes SS braided lines and EBC sintered brake pads.
• Standard Plus Kit: Includes SS braided lines, EBC sintered pads and an EBC Carbon Steel front rotor.
• Super Plus Kit: Includes SS braided lines, EBC sintered pads and EBC carbon steel front and rear rotors.
• Deluxe Kit: Includes SS braided lines, EBC sintered pads and an EBC Premium 320mm SM front rotor kit.
• Super Deluxe Kit: Includes SS braided lines, EBC sintered pads, an EBC Premium 320mm SM front rotor kit and EBC rear rotor.

A new high output stator for the XR650L. 25% more output than the stock unit. Approximately 50 additional watts. Now you can have enough power to run those driving lights and/or heated riding gear!

Choose mechanical or hydraulic brake switches for your dual-sport conversion

Operates turn signals, horn, headlight high/low/running/off, kill button. Blue LED high beam indicator. Includes wire pigtail with male & female 9-pin plug connectors. 1.75 inches wide. Wiring key included.

ProCycle Rev Box increases the rev limit to 10,000 RPM. In addition, this unit offers a re-mapped timing curve which yields a noticeable increase to horsepower and torque over the stock CDI

This CDI box is a direct plug in replacement CDI. Simply locate and remove the stock CDI, and plug the unit directly into the wiring harness, no modification needed. Suitable for stock and modified machines

Hardened chrome vanadium steel with built in rubber insert to hold spark plug steady.

Thin wall bi-hex sockets designed to access narrow spark plug holes.

• Use with 3/8" drive ratchet or wrench
• Choose the one that fits your spark plug size:  14mm, 16mm, 18mm, or 21mm.

This is a great Dual-Sport tire from Dunlop. Designed for the true 50/50 rider. An Adventure product for the price-conscious customer. Full tread depth pattern designed for rigorous off-road use yields excellent traction on everything from hard-packed fire roads to soft single-track trails. Versatile tire performance allows riders to travel on the street and venture off-road. A tire equipped to go anywhere, the D605 is a value option for the all-around rider. DOT approved.

Here is another great upgrade for the TW200 or the VanVan front tire.

Universal 'old school' trials type tread pattern. A versatile performer with a tough nylon carcass and raised dimpled knobs that work well in a variety of terrain.

• Narrow knobby configuration means less of an environmental foot print on the trail
• 4 ply rated
• DOT approved
• Not intended for extended highway use

Tire size is 4.00-18 (64P load / speed rating)

Kenda's Dual-Sport tire designed for the 80% on-road, 20% off-road crowd.

• DOT approved
• Unique combination of street and off-road grip provides maximum performance
• Strong and durable Nylon four-ply construction
• The advanced compound design gives better stability, cornering traction and braking control
• Tube type tire H-rated (max speed of 130 mph)

Our Heavy-Duty tubes are made specifically for off-road riding. These are the sturdiest, highest quality tubes on the market. They are 3mm thick with natural rubber construction to better resist pinch flats and are easier to patch than butyl rubber tubes. These have a straight metal valve stem. New tubes deserve new rim strips. Don't forget to add them in to your order.

• 17" tube works with 120,130 and 140 metric tires or 4.50 to 5.10 inch size tires
• 18" tube works with 100 to 130 metric or 4.00 to 5.10 inch size tires
• 19" tube works with 100 to110 metric or 4.00 to 4.60 inch size tires
• 21" tube works with 80 to 100 metric or 3.00 to 3.50 inch size tires

The Bag Snake kit works great for rear bags and side bags. When rigged with a side bag the second ring on the ring tensioner creates a secondary buckle so you can loosen the top for access and your bag doesn't fall away from the bike.

When rigged for a rear bag the diagonal section of the strap prevents any slippage over the ends of the bag. For this reason, the Bag Snake is great for smaller rear bags.

Kit Includes:

• 1 Heavy Duty Cam Tension Loop
• 1 Heavy Duty Metal Ring Tension Loop
• 1 Six Foot Runner Loop
• 1 Heavy Duty Metal Ring Loop

Our Tool Tube mounts in place of the little stock tool carrier. The tube is made from 3 1/2" O.D. ABS pipe. It's held by 3 strong powder coated steel straps. Both ends are sealed with waterproof expanding plugs. This is the ideal way to carry those items you always want to have with you on every ride. Tube is approximately 13" long.

You can now order your Tool Tube with a Locking End cap, mini padlock and keys included, on the exposed end.

If you already have a Tool Tube you can order just the Locking End Cap and lock.

• Smartly designed to accommodate, but not limited to: 1 gal. - 1.75 gal. Rotopax fuel/water packs, Wolfman Luggage - Wolf Tail bag (M303), and Givi Monokey top cases (separate mounting kit required)
• Large 14.5"(Width) X 13"(Length) luggage platform
• CNC laser cut from 1/4" 5052 Aluminum - weighing only 2lbs. 10oz.
• Each rack is sand-blasted and sprayed with a premium DuPont semi-gloss mini-tex powder-coat finish
• Stainless hardware kit and installation instructions included
• All materials and craftsmanship are sourced 100% in the USA
• Carrying capacity is 20lbs.

• Revolutionary Parafilm™ formula; spray it on and let it dry
• Doesn't fling off
• Sprays on wet, dries to waxy film and seals the lubricant to your chain
• Non-gooey finish keeps dirt, sand and grit from sticking to freshly lubed chains
• Translates into longer chain life and reduced sprocket wear
• 5.5 oz net wt Aerosol

• Large display, readings are shown to 0.1 psi
• Kpa and Kg-cm2 scales also provided
• Reads up to 99 psi
• Ergonomic shape fits nicely in your hand

High Quality Replacement Wheel Bearings and Seals for your TTR125 with disc brakes.

Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.

Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.

Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.

Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.

Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.

The rubber coated outside diameter creates an optimum seal at the hub.

Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.

A 'wrench style' tool to turn the 'square top' tappet screws. The wrench does a better job of holding the adjuster screw still while tightening the locknut. Slim and flat, this tool is easy to carry in a tool pack.

Ready to go tool kits. Just toss it in your bag and hit the road... or the trail.

A pack of 10 Fuji style lock nuts to put on the sprocket of your KLR650. These are an 8 mm, flanged type nut that will keep your sprocket snug and tight.