Precision tolerances – The tightest in the industry. Ultra-lightweight, for reduced unsprung mass.
Straight rate springs will give better control in the rough stuff. Sold in pairs.
Race Tech has developed these fork springs specifically for the heavier weight of the KLR650.
Sold in pairs.
Not for 2014-2018 New Edition
Race Tech HP Springs have a high stiffness-to-mass ratio. In other words; the springs are light weight for their particular spring rate. This requires the finest materials and processing. Shot-peened and pre-set so they cannot sack out. All Race Tech HP Springs have the highest rate tolerances in the industry. These are the finest springs in the world-guaranteed.
OEM spring rate is .46kg. We offer stiffer spring rates from -5% to 10% for riders who wish to carry luggage or just prefer stiffer suspension.
5% Less than stock
Sized perfectly for adult back-yard racing or fast/aggressive mini riders. This is the most important upgrade you can make for an adult sized rider. The stock suspension is too soft for most adults and aggressive kids.
Sized perfectly for adult back-yard racing or fast/aggressive mini riders. This is the most important upgrade you can make for an adult sized rider. The stock suspension is too soft for most adults and aggressive kids. Fits stock shock.
Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
For Disc Brake Models Only
This kit is for the REAR caliper.
Includes front and rear brake pads.
Here's an easy way to add a Tach to your motorcycle.
Performance CDI for the Yamaha TTR125 increases the rev limit by 1,000 RPM over the stock rev limit. Easier starting, crisper throttle response.
This CDI box is a direct plug in replacement CDI. Simply locate and remove the stock CDI, and plug the new unit directly into the wiring harness, no modification needed. Suitable for stock and modified machines.
The Shorai LFM Duration Recommendation is the best overall pick for most applications, and has been selected to give strong cranking performance and long lifespan.
Measures 4.45" x 3.5" x 2.28"
Weight (lbs): 1.52 lbs
Weight (kg): 0.69 kg
Cold Cranking Amps: 210
Polarity: [- +]
Each Shorai battery includes self-adhesive foam panels to achieve a snug fit in your battery box.
The Shorai LFM Standard Recommendation is the best overall pick for most applications, and has been selected to give strong cranking performance and long lifespan.
Measures 4.45" x 3.5" x 2.28"
Weight (lbs): 1.52 lbs
Weight (kg): 0.69 kg
Cold Cranking Amps: 210
Polarity: [+ -]
Each Shorai battery includes self-adhesive foam panels to achieve a snug fit in your battery box.
Optimate Lithium 0.8A
At 0.8A, it’s a lower amp charger but still charges or maintains All 12V LiFePO4 batteries, protecting and keeping the battery at 100% charge. A great, cost-effective charger for your lithium battery maintenance.
A unique LiFePO4-specific program recharges and balances cells within the battery efficiently and safely. BMS re-activates battery from sleep or deep discharge protection mode. Protects LiFePO4 batteries in the most effective way. Protects a large investment and guarantees Lithium Iron Phosphate (LiFePO4 / LFP) batteries will perform as advertised for a very long time.
No risk of overcharging. Totally safe for vehicle electronics. Sparks suppressed. Safe for long-term battery maintenance. Automatic shut-down if short-circuited or battery disconnected.
Rear Sprocket
Note: 2002 and later models have a 10mm sprocket bolts. 2000-2001 models have 8mm sprocket bolts.
High quality steel front sprocket
For reference, the stock gearing for the WR250R is 13/43 while the X model runs 13/42 stock gearing.
Reduce the friction dragging down your drivetrain. This chain roller is made from Delrin®, it's self-lubricating and a significant improvement over stock.
Does not use a bearing but rides directly on the frame boss. There is no mounting hardware included.
A CNC machined chain guide for the DR. Stronger than the wimpy stock unit and can easily accommodate the stock 525 chain as well as a 46 tooth rear sprocket (by moving the lower rub block to the forward position). The rub blocks are also a higher grade, longer lasting material.
Fit Disc Brake Models Only
Folding tip, forged aluminum shift lever from BBR Motorsports. Stronger and lighter than the stock shift lever.
- Pivot CP clutch and brake lever set for Trail models.
- Lever folds outward to prevent breakage in the event of a crash.
- Lever adapter is ultra precise CNC machined out of high grade aluminum for super light weight design.
Black anodized 49 tooth 7075 T651 aluminum sprocket.
Tune your stock carburetor for better power and response, easier starting and quicker warm up. Mikuni main and pilot jets.
Geared for the do-it-yourselfer that already has a TM40 or HS40. This kit supplies everything you need to convert it for use on your bike.
Kit includes intake and air boot adapters, throttle cables, choke knob, accelerator pump nozzle, a wide selection of main and pilot jets plus a TM40 tuning manual.
Complete kit to rebuild OEM carburetors.
The perfect dry trail pack from Moose. Constructed of heavy-duty waterproof tarpaulin with heat-welded seams. Heavy-duty ITW quick-release buckles and YKK water-resistant zippered external pockets make for a versitle bag.
The roll-down top creates a truly waterproof seal for the main compartment. Dual compression straps provide a secure closure and can be used to store gear externally as well. Coated tarpaulin material makes cleaning a breeze. Available in three great sizes - 25, 40 and 60 liters.
If you like these bags, you might like the matching ADV1 Backpack.
This carry rack is solid and durable made from 5052 aluminum and with its sleek design it will not catch on your clothes or nature.
It is an easy install and will allow you to strap your cooler, lunch box, tools, or whatever on the back of your new Yamaha.
Comes complete with all hardware and easy install instructions.
Not only are Pro Moto Billet Cargo Racks brutishly strong and functional, but they look great too. Each cargo rack is methodically engineered, then CNC machined on-site from a 1/2 inch thick plate of USA made 6061 aluminum by master machinists.
The cargo racks are then hard clear anodized for durability. PMB uses only stainless steel fasteners for worry-free years of riding. Excellent instructions and all necessary hardware is included.
Need to mount your turn signals to your new Pro Moto Billet Rack? Just add a set of CNC machined aluminum Turn Signal Brackets.
Cycle Racks Bag Supports can used for many different Cycle Racks and can be used on either the front or rear rack.
When they developed these, they wanted a functional, yet "Easy On- Easy Off application. The pig tail hook goes up, over and underneath the bar of the rack, they can also be used upside down on the rear rack as side boards. To install them, wing them out, slide them in place and then wing them back down. Simply reverse the process to remove them.
Rok-Straps are supplied to secure them in place. They are pre-drilled to accept the pattern of the Roto-Pax Pack Mount (sold separately) so you can carry fuel or attach them to your own bags.
They are sold together in a set of one right support and one left support.
COLOR: Black
The Front Rack gives a lot of options for functionality.
CycleRacks are made out of Schedule 40 11/16 black steel pipe, bent in a press, and welded together in a jig.
All of their products are 100% made in the USA. If the rack is ever broken for any reason, CycleRacks will replace it for free, you just pay the shipping.
Their rear racks are great for adding the extra storage needed for your next adventure. They are the perfect size for a backpack or small duffel bag. Their steel racks are built to handle any riding style you throw at them, now Rotopax ready! This is the ENDURO Series CRF300L rear rack which measures 10 inches wide and 12 inches long.
Easy to Install
PMR side utility racks are great for strapping down your soft luggage and keeping it off the rear plastics and exhaust pipe, while adding plenty of new tie down points for any luggage you have on your seat or tail section. They also add an enhanced level of security and strength to the rear end of your motorcycle in the event of a tip over or crash.
Sold as a pair. Easy to Install
This is a completely rebuildable stroker crank (3mm additional stroke) turns your mild mannered 250cc motor into a 263cc trail shredding monster! OK, maybe not, but sure makes it a fun machine.
Want the COMPLETE package? Order a Big-Bore kit to go with your stroker! That will give you a 308cc ripper! That is 24% larger than the stock 250. This package includes the Athena Big Bore Kit plus the 3mm Hot Rods Stroker Crank with new Genuine Yamaha crank bearings.
You will need to tune your EFI with something like the Power Commander V to get the most out of your Stroker kit.
For stock bore Hot Rods highly recommends you use the Vertex Stroker Piston Kit.
7.48mm diameter - Includes three valve shims of each size from 1.20 to 3.50mm in .05mm increments.
141 shims in total. 0.57 cents per shim! Does your local dealer have the shims you need?
If you're plannig to or already have a stroker crank setup in your Yamaha WR250R/X, you'll need this stroker piston.
Features:
From Barnett, the number one name in motorcycle clutches since 1948, we now offer a complete high performance clutch set. This includes Kevlar friction plates, steel drive plates and stronger springs.
Adjusting your valves or setting your cam chain tension? Here are the O-Rings that fit in the TDC sight plug and the crankshaft nut access plug.
Providing unbeatable performance and exceptional value, Hi-Flo Filter is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide. The filters are also supplied to original equipment manufacturers as well as private label brands.
Grab our 5-pack and save both time and money!
Providing unbeatable performance and exceptional value, Hi-Flo is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide.
Grab our 5-pack and save both time and money!
The starter bushing in the DR650 leads a tough life. Exhaust heat and minimal lube from the factory take their toll. Warp 9 has a high quality solution - a billet starter cover with a sealed ball bearing.
For the DR650 that has been lowered or converted with supermoto wheels. This stand is 1.5" (40mm) shorter than the stock unit.
Includes a rear shock mount cover plate and plug for lowing the stock shock.
Light weight and strong. These DRC foot pegs have a wider platform for increased comfort and control. Cast from Chromoly steel for unbeatable strength and durability.
The new Fastway Evolution AIR footpegs are now the ultimate pegs in the Universe.
Designed and sculpted out of the best 7075 Billet aluminum by Pro Moto Billet elite engineers and machinists. Featuring Fastway's Patented adjustable height, traction, and camber options, the Evolution AIR footpegs are superior in every way. Fastway Evolution AIR pegs are designed to shed mud and debris, while being ultra strong.
You can also order serrated or spiked cleats separately. See images.
These AIR pegs are offered in several colors, but some colors may require extra time, call for availability.
Pivot Pegz have set a new standard in footpeg performance and quality and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty.
Pivot Pegz aim is to build the best footpegs in the world and they really do perform as good as they look. Here's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever.
Sharpen Your Yamaha WR250R’s Look with B&B Off Road’s Tail Tidy
Give your Yamaha WR250R (2008-2021) a shot of attitude with B&B Off Road’s premium tail tidy! This innovative replacement ditches the bulky stock fender for a sleek and stylish design that elevates your bike’s aesthetics without compromising functionality.
Clean Lines, Easy Installation:
This tail tidy boasts a streamlined design that sheds unnecessary weight and bulk, instantly transforming your WR250R’s rear end. The straightforward installation utilizes existing mounting points for a hassle-free experience – get ready to hit the road (or trail) in no time.
Choose Your Finish:
Personalise your tail tidy to match your WR250R’s personality. Opt for a gleaming polished finish for a bold statement, or choose the classic black PPA-Gloss for a refined look. The brand new, low-lustre textured black powder coat (PC) offers a stealthy aesthetic for a more aggressive stance.
Unleash Your WR250R’s Potential:
This tail tidy doesn’t just enhance your bike’s visuals. The reduced weight contributes to improved performance, letting your WR250R handle even better. With a cleaner and more streamlined rear end, your adventure awaits in style.
Upgrade your Yamaha WR250R today! Order your B&B Off Road Tail Tidy and experience the perfect blend of functionality and sharp design.
Make the Edge-2 installation as easy as possible with an Optional Connector Set. This allows you to put an OEM style connector on the Edge Taillight making the connection simple. Stock plug will go right into this unit and off you go. Will need a crimp tool or set of needle nose pliers to crimp connectors on.
The Edge-2 Tail Light and License Plate Holder is a simple bolt-on replacement for the stock unit. Included is an aluminum mount for the light and license plate that is model specific. The light unit uses 16 high-intensity red LED's for tail / stop light function. 3 white LED's are used for license plate illumination.
Included is a set of turn signal brackets that bolt to the mount, but these are designed for a smaller LED type signal with a mounting stud of just 8mm. Or consider the Edge-2 Upgrade Circuit Board as this converts your brake light into a functioning turn signal as well!
NOTE: LED's must be installed on a 12 V DC system!
Make the Edge-2 Circuit Board installation as easy as possible with an Optional Connector Set. This allows you to put an OEM style connector on the Edge Taillight making the connection simple. Stock plug will go right into this unit and off you go. You will need a crimp tool or set of needle nose pliers to crimp connectors on.
Easily turn your blinkers into additional running lights and brake lights (rear) for added visibility.
White light in the front and red in the rear. Rear red running lights and bright red brake lights. You can omit the running and brake lights if you wish and still have the best blinkers on the market.
Dazzling bright Amber blinker functions.
Everything comes in a spring-loaded stock designed to keep it safe from those unexpected tip-overs, crashes, or encounters with brush and trees. They’re flexible enough to bend 360 degrees, yet tough, durable, and almost impossible to break!
If you have a single indicator light for the blinkers that is not built into the display and is not LED you will need the diode kit (AKA DR650) If it is built into the speedo display it should not require the diode kit.
Available in a generic kit with Bullet connectors supplied. Great for your DR or almost any other bike with a single post blinker setup. These will work well on bikes that use a flasher, but you might have to add the female side of the connectors that are included in the kit.
Not for Yamaha T7, see model specific listing
Triangle/Teardrop style signals with LEDs. Mounts on any flat surface to keep out of the way of brush, branches, and your exhaust system. Requires LED flasher or LED turn signal resistors to flash properly.
This devices allows any two wire after market LED turn signal indicators to operate as running lights (always on), and will blink on / off when the turn signal switch is activated. It is highly recommended to use this product with the Fixed Rate Turn Signal Flasher. This device, as well as aftermarket turn signals, use much less current than stock turn signals, thus an increased flash rate will occur. Load resistors or a fixed rate turn signal flasher will get your flashers operating at the normal flash rate again.
Each package contains two separate adapter boxes, good for operating both turn signals, left and right of either the front OR rear of your motorcycle. You will need to purchase a 2nd kit if doing the Front AND Rear of the motorcycle.
This device is universal; designed to work for any motorcycle with a DC electrical system. Kit comes with bullet connectors to wire in manually. Works with any two wire non-sequential aftermarket LED turn signal indicators.
JNS has come up with another great addition for the little XT250. Auxiliary light mounts that keep the lights up high for great projection, but still good and tight to the bike for protection. These heavy duty 1/8" stainless steel mounts put your lights out of harms way without interfering with controls, body work, or the fuel tank. Includes four longer upper triple clamp bolts. Everything but the lights themselves to light your way through the darkness.
Motoz Tractionator Desert H/T series of tires are renowned for great traction and long wear life. These tires are designed to handle hard terrain, fast and rocky trails as well as gravel roads and desert hard pack. Tricky off-cambers, ruts and hard braking at extreme lean angles are no problem for this DOT approved tire.
Note: Tubes can be run in Tubeless tires, but a Tube Type tire cannot be run Tubeless.
We start with Excel or Sun rims, OEM hubs, and Buchanan's heavy gauge stainless steel spokes. Rims and spokes are precision machined for a perfect match to your bike.
Our pro shop then laces and trues your wheels to perfection, giving you the highest quality set of custom wheels available.
Add tires to your wheel order and we will throw in tubes and mount and balance them at no additional charge.
We start with an Excel rim, OEM hub, and Buchanan's heavy gauge stainless steel spokes. Rims and spokes are precision machined for a perfect match to your bike. Optional upgrades include SUN rims available in 3 colors.
Our pro shop then laces and trues your wheel to perfection, giving you the highest quality custom wheel available.
Add a tire to your wheel order and we will throw in a tube and mount and balance it at no additional charge.
Complete set of 'Adventure' wheels. These are the same rim sizes as used by the BMW GS and other big adventure bikes. The 19" front and wide 17" rear will give you great twisty road handling on the pavement while still being dual-sport friendly.
We start with silver Excel or Sun rims, OEM hubs and Buchanan's heavy gauge stainless steel spokes. Rims and spokes are precision machined for a perfect match to your bike.
Our pro shop then laces and trues your wheels to perfection, giving you the highest quality set of custom wheels available.
Add tires to your wheel order and we will throw in tubes and mount and balance them at no additional charge.
We start with an Excel rim, OEM hub, and Buchanan's heavy gauge stainless steel spokes. Rims and spokes are precision machined for a perfect match to your bike. Optional upgrades include SUN rims available in 3 colors.
Our pro shop then laces and trues your wheel to perfection, giving you the highest quality custom wheel available.
Add a tire to your wheel order and we will throw in a tube and mount and balance it at no additional charge.
High Quality Replacement Wheel Bearings and Seals for your TTR125 with disc brakes.
Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.
Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.
Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.
Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.
Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.
The rubber coated outside diameter creates an optimum seal at the hub.
Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.
| Description | QTY per Kit |
| Ball Bearing | 2 |
| Seal | 2 |
A set of six high quality grade 10 sprocket bolts with lock nuts. Thread-lock compound has already been applied for extra security.
These bolts are flat head style, requiring a countersunk hole in the sprocket.
The EVO R is a tried-and-true series that will save weight, add noticeable performance gains and sound tremendously better than stock.
The T-6 exhaust system contains a stainless steel head pipe, brushed aluminum canister and a carbon fiber end-cap for added durability and a professional look. This exhaust system features the same benefits as the T-6 Stainless Steel Exhaust System, but is designed to fit Yamaha's TT-R125 model. In addition to all of these features, the T-6 will come with a removable United States Forest Service approved spark arrestor for trail/off-road riding.
Features Include:
The Mini Powercore 4 is the best bang for your buck performance exhaust system out there.
Offered as a standard Mini Powercore 4, or as a Spark Arrestor Version, the Mini Powercore 4 features a Hi-Flo stainless steel core and formed end caps, an aircraft grade aluminum canister and a durable stainless steel header. It is pounds lighter than stock and you will swear the motor has been bored and stroked with the first twist of the throttle.
The science behind the MegaBomb header may be FMF's greatest engineering accomplishment to date. You can bolt on a MegaBomb with an existing FMF Racing slip on for as much as a 3hp boost, plus the MegaBomb actually reduces noises levels by as much as 1.5dB. The MegaBomb technology is evolved to produce more low end to mid range gains as well as broadening out the mid to top end power gains over stock. MegaBomb is the next level technology you can have today.
For FMF mufflers only
The EVO R series draws on our rich heritage of making power. Offered for various off road MX and sport ATV models, the EVO R is a tried-and-true series that will save weight, add noticeable performance gains and sound tremendously better than stock.
Yoshimura RS-3 that will slip right on to your stock header. Made by hand to the highest quality standards using the championship-winning racetrack experience and their extensive R&D facility ensure these pipes perform and will last.
Both full systems and slip-on mufflers include 96 dB sound insert/USFS approved spark arrestor installed in the muffler. Mid-pipe is stainless steel while the stainless RS-3 oval muffler design has a slim profile with an aluminum end cap.
Works on OEM header only!
Seat Concepts new seat is wider to help keep you comfortable for those long commutes or Dual-Sport rides. The added width and foam density helps keep the seat from being the item that stops you from going on those long rides. The Complete Seat comes with an high quality aftermarket seat pan, and the foam and cover installed, ready to ride.
| Width: | 9.5" (241mm) |
| Height: | Same as OEM |
State-of-the-art replacement seats, Sargent seats are built on a percision-molded lightweight Polytec seat pan. Sargent's proprietary seat foam (Super Cell Atomic Foam) is their own unique blend of resilience, firmness, and vibration-absorption qualities, making it well suited for long distance comfort and support. Sargent seats are covered in a marine-grade, UV-stablized mildew resistant CarbonFX vinyl. These seats will fit bikes with the stock, IMS, or any other aftermarket fuel tank.
New wider seat to help keep comfortable on that long commute or dual-sport ride. The added width and foam density will help keep the seat from being an item to stop you from going on that ride or enjoying the bike.
Each kit contains detailed instructions for easy "Do It Yourself" installation. This provides the highest level of quality & comfort at an affordable price.
Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!
The Foam and Cover Kit is only for the OEM pan. It DOES NOT include the pan.
Only Available in Tall; All Carbon Fiber
| Width: | 9.5" (241mm) |
| Height | 1" (25mm) TALLER than the stock seat |
From JNS Engineering, a super solid Rear Master Cylinder Guard for the XT250, WR250R and X. CNC formed and then powdercoated black for lost lasting corrosion protection. Did we mention how good it looks? All hardware provided.
Master Cylinder guard by Moose Racing will protect the exposed rear brake master cylinder from damage
PSR has a new shark fin rear rotor protector for the big XR and XRL. CNC machined from forged aluminum and then anodized gun metal in color. This unit bolts to the stock caliper bracket.
Mount Barkbusters standard aluminum bar handguards to 1-1/8" motorcycle handlebars with the Barkbusters Tapered handlebar saddle clamp set.
What's in the box:
These are all you need to mount your current Barkbusters Handguards when you upgrade to a tapered oversized 1 1/8" handlebar.
Replacement handguards for your Cycra set up. Injection-molded high-impact plastic replacements. Includes all hardware needed for mounting.
Moose Racing's Heavy-Duty, 4mm thick 5052 aluminum, to protect expensive and fragile radiators from side impacts and twisting.
Made of military aircraft grade 3/16" cast acrylic, this guard will protect your lens from roost, rocks and branches. Optical clarity of the acrylic ensures brightness and projection of your headlight are minimally effected while all the while protecting your headlight from impact and abrasion.
Guards are held to the headlight lens with an industrial strength hook and loop system on each corner.
Designed to enhance the appearance of your motorcycle, yet provide greater riding distance per tankful. Larger capacity than stock, yet very slim and sleek. Perfect for the dunes or the race track! These tanks are made with crosslinked polyethylene for extra strength and durability.
Natural color is recommended to easily see the fuel level in the tank. Includes cap and fuel petcock.
Dielectric Grease is an insulating silicone grease designed to insulate and protect electrical connections. Pack it into the back side of electrical connectors to protect them from moisture and corrosion. Do not put it directly on the connection surfaces.
Replacement side panels from ProCycle (formerly DSA). These pieces are fully compatible in any combination with the original factory plastic. These side panels have a crisper, more angular look than stock. Vacuum molded, they are a design improvement over the stock panels.
Sold in pairs
Does not include heat shield. Depending on your application and preferences, more than one optional heat shield may be useful.
Left and right stock OEM Suzuki side panels plastic sold as a pair.
Includes one heat shield. Depending on your application and preferences, more than one heat shield may be useful. Extras can be added here.
Rear Fender comes with built in tabs designed to be used with Maier USA Side Panels.
The long over-due rally shield for the 2008-on KLR650 is finally here!
Parabellum uses 4 steel brackets mounted to factory locations as well as our stand-off windshield design to ensure the customer doesn’t have to drill extra holes in the cowling but still achieves that iconic upright look of the real Dakar Rally bikes.
The Rally shield protects the rider’s torso/chest from air, cold, roost, branches and bushes while leaving the rider’s head/helmet in clean air. We recommend the Rally shield for riders seeking some protection, but prefer to be off-road.
The Rally shield is made from 1/8 inch cast acrylic and is 11.5 inches wide at the bottom and 17 inches tall.
RotoPax are Rotational Molded - the process which produces indisputably superior products.
Need to mount two containers? A water and a fuel? Two waters? Finally, you can stack multiple packs together! Use in conjunction with a pack mount. You will need to purchase the Single Mount as well as the Extender.
The GPR v5 is the fifth generation steering damper designed for dirt bikes, adventure bikes but is also used on several of hybrid applications. Its compact and slim design allows for the damper to be mounted below the handlebars, out of harm's way, without raising the bars more than an inch. Frame mounts are machined steel or Cryogenic treated billet aluminum with stainless steel pin, and billet aluminum machined bar-mounts.
Will only work with Fat Bar style (1 1/8" clamp area) handlebars and stock triple clamp.
Filling and bleeding a Magura hydraulic clutch does not need to be a routine chore and should only need to be done when air infiltration within the system is suspected. Magura uses mineral oil, which does not absorb moisture from the environment, to lubricate the whole system.
Note: Magura hydraulic systems use ONLY mineral oil. Do not introduce DOT brake fluid of any kind into a hydraulic system designed to use mineral oil as this will cause corrosion to the internal seals and system failure may result. The only time anyone should ever need to replace the hydraulic fluid in a Magura system is following a hydraulic line exchange, a system upgrade, a crash which has damaged the system components or in a situation where a lack of fluid within the system has been diagnosed by poor lever feel.
If you do need to bleed your Magura hydraulic system, their custom made kit does indeed make that chore easier.
This heavy duty DRZ400 chain guard is made of laser cut 1/8” aluminum and finished in textured black powder coating. The formed flange helps keep chain grime off the rear tire.
Mounting hardware included.
This holder is the quickest and easiest tool out there to get a grip on that hard to handle hub.
Laser cut to the exact pattern that EBC makes their clutch plates from, it makes loosening and re-tightening the clutch nut a breeze, and minimizes the likelihood of damaging the clutch hub.
This kit is for those of you looking for a bit more arm room and a better platform for your feet in the TW cockpit. Included are ProCycle Wide Foot Pegs and our oversize bars with 30mm risers.
Kit does not include new throttle tube. If you have 2001 or newer TW200 and would like a new billet aluminum throttle tube, please select the addon box to receive one with your order.
