Simple, lightweight rack made from rugged 1/8" 5052 Aluminum, with a rigid 5-point mounting system.
Low profile allows for easy seat removal.
Features:
Note: Placement of this top rack does require removal of the stock tool bag.
An OEM type replacement for the mighty XRL from the folks at Fuel Star. Single inlet that threads directly onto the stock fuel tank. Also works on the adapters that come on some aftermarket large capacity plastic tanks (like IMS).
Kit comes with a new Petcock, O-Ring, Fuel Line and Fuel Line Clamps! Everything you need for a complete fuel connection replacement.
Folding tip, forged aluminum shift lever from BBR Motorsports. Stronger and lighter than the stock shift lever.
Has both high and low beams. Attaches to the upper fork tubes with rubber straps. DOT and CE approved.
Taillight, brake light, & license plate light. Attaches to the top side of enduro style (XR, KDX, etc) rear fenders. Dimensions: 2 3/4" x 4 3/4" x 2 1/2" tall. Wiring instructions included.
This LED taillight replaces the factory taillight in Honda CRF450X and CRF250X rear fenders. Features a taillight and a brake light for a clean looking dual sport conversion. Wiring instructions included.
CNC cut and bent and then artistically welded, these are much more stout that the stock plastic unit. No worries of them cracking and falling off in the middle of nowhere.
Here is a tool to help you remove a few links from a chain that is too long. A great tool to have in your tool box.
The head of the pivot pin you are going to remove must be ground down level with the side plate before using this tool to push it out. Failure to do that will cause damage to the tool that is not covered by any warranty!
We like red high temperature silicone for use as an adhesive. It is much stronger and sticks better than the standard stuff. The resistance to temperatures up to 650°F is a bonus. Sold in a 3 oz tube.
This is a simple three piece kit you can install in minutes that cleans up the stock DR rear-end. We use the 250 taillight that fits perfectly into the pocket of the stock taillight on the DR650 fender. It is smaller, looks great and is out of harms way more than the stock unit. It is a total 'plug-n-play' as the wire pigtail plugs right into the DR650 harness just like stock. Then we use a small LED light to keep you legal and illuminate your license plate, which gets mounted to our custom stainless steel bracket, eliminating the stock ugly plastic mount.
Kit includes:
Sintered Off-Road Brake Pads for the front disc brake.
Their best selling product to protect your bike, Flatland Racing skid plates are made from 5052 3/16" aluminum plate.
They are all hand tig welded together with side engine guards. Installation is easy with our clamps that grip tight.
Their skid plates offer clean out slots and oil plug hole, making oil changes simple. These are more durable than carbon fiber and plastic.
Mounting hardware and instructions included.
Made from strong and light 5052 aluminum to hold your license plate firm and up, out of the way for maximum tire clearance, prefect for your new dual sport bike.
It uses the original tag light with out any modifications to your bike. Mounting hardware and instructions included.
In the event of a crash or even just a dropped bike, these heavy-duty crash bars will prevent major damage.
The powder coated 1" steel tubing is bolted to the sub frame of the bike with two attachment points on each side, preventing them from rotating in the event of a low side.
The guards also feature aircraft grade aluminum plates that can be inexpensively replaced without needing to purchase a new set. Think of them as protection for your protection.
They use highest grade commercially available 12.9 (177,000 psi in tensile strength) wherever possible. Rest assured that you are getting the best material commercially available.
Most skid plates will require notching or modification to avoid interference.
Will not fit properly with oversized head pipes.
This handy storage case for needed tools will fit in any Wolfman bag, including the Enduro Tool Bag.
Dimensions:
The low-profile Klamath Tail Rack Pack keeps gear organized and easily accessible — like a tank bag for the tail end of the motorcycle. The 4-liter soft luggage case features a zipper-less nested clamshell design inspired by classic motorcycle rally racing packs.
The Klamath attaches securely to virtually any motorcycle tail rack, many dirt bike rear fenders, and Giant Loop’s Siskiyou Panniers or MoJavi Saddlebags. Now even faster and easier to install and remove, with two included 25″ Pronghorn Straps.
Muc-Off Air Filter Cleaner is a state of the art, professional strength bio-degradeable cleaner that's designed to clean and care for foam filters. Its unique combination of active ingredients is formulated to rip through dirt and oil in seconds, without damaging the foam or glue.
The Givi skid plate, manufactured from 5mm aluminum, is lightweight and offers excellent protection for vulnerable engine components, whether you have a standard or DCT transmission. All necessary hardware and instructions are included. Compatible with stock sidestand and centerstand.
Provide absolute protection for your AT by including Givi Crash Bars, available in either Black powdercoating or Stainless Steel.
A quality set of replacement throttle cables from Motion Pro.
The Ohlins Africa Twin shock has knob adjustable rebound and compression damping on a 46mm machined aluminum body combined with a hydraulic remote preload adjuster with a hose mounted actuator and mounting bracket. The gas reservoir uses a much higher quality compression adjuster/head valve along with a solid separator piston to prevent gas bleed-over. The improved adjuster circuits provide a wider range of adjustability.
Solo riders with light loads should select the 9.7 spring. 2-up riders or heavier loads select the 10.7 spring.
Features and benefits of this Ohlins shock:
Carbon steel brake rotor. Makes it easier to swap over your spare rear wheel.
Quality windscreen made from Lucite aircraft acrylic making it more rigid and optically clearer than OEM windscreens
These models are 2"-4" shorter or 2"-4" taller than stock to meet your particular riding preference.
Steel cargo rack from Moose Racing. It features a nice wide platform and a durable powder coat finish. 17" wide and 10" long.
Pivot Pegz have set a new standard in foot peg performance and quality and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty.
Pivot Pegz aim is to build the best foot pegs in the world and they really do perform as good as they look. There's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever.
Clutch and Ignition covers made by B&B Eng. Formed from 2mm thick 5052 aluminum plate, selected because of its strength, corrosion resistance, excellent abrasion and impact protection. These will help protect your cases in the event of a bad fall.
These covers are attached to the engine cases with high quality heat resistance silicone adhesive
These covers will NOT fit early kick start only models that did not come standard with electric start. If you have added a kick starter to your bike that came with an electric start, covers will fit with no problem.
Complete Swingarm Bearing kit to replace the bearings and seals in the WR swingarm pivot.
Complete kit to replace the bearings and seals in the WR shock linkage. Includes the lower shock bearing.
| Kit Contents: | |
|---|---|
| Seal | 8 |
| Needle Bearing Shaft | 6 |
| Needle Bearing | 5 |
Make the Edge-2 Circuit Board installation as easy as possible with an Optional Connector Set. This allows you to put an OEM style connector on the Edge Taillight making the connection simple. Stock plug will go right into this unit and off you go. You will need a crimp tool or set of needle nose pliers to crimp connectors on.
These awesome rotors are laser-cut out of a high-carbon content 410 stainless steel, lap cross hatch ground, and heat-treated. The finished rotors are mounted on a floating black steel carrier for durability and strength.
The floating pins are an oversized CNC machined stainless rivet with stainless wave washer to ensure these rivets will not crush like more traditionally used steel pressed rivets. high temp paint is applied to surfaces like cooling holes and edges to provide a clean finished look.
Includes a fresh set of brake rotor bolts.
Renthal chain lube is 100% lubricant, zero propellant. So this new 250ml bottle size combines high performance and value.
The all-new formula Chain Lube is specially designed to penetrate all parts of the chain. This all-condition lube is compatible with all o-ring and non o-ring chains.
This new unit from JNS will protect your cases from the damage caused by a thrown chain, and will also keep your pants, boots or foot safe from your countershaft sprocket.
The case saver portion is laser cut from 0.25" aluminum and then has the 0.19" aluminum countershaft sprocket cover welded to it and the entire unit is powder coated black.
All the mounting hardware is stainless steel with machined aluminum spacers also included.
If you have a 16t front sprocket, mounting modification may be needed to fit. Install the case saver on the bike without the top spacer and bolt. This provides a little extra wiggle room. Add the top spacer and bolt after the bottom bolts are loosely threaded.
Savvy DR650 owners will remove the upper chain roller. You can use this stainless steel button head screw to plug the threaded hole. Suzuki did not make the upper roller mount strong enough. If you don't remove it yourself the chain will likely do it for you - along with a chunk of metal out of the frame.
Complete kit of OEM quality patrs to replace the bearings and seals in the swingarm pivot.
Replace your lost or broken stock plastic chain guard with a JNS aluminum one. Laser cut, CNC formed, TIG welded, and powder coated a beautiful satin black. This is a direct replacement for the stock unit.
Please note that this unit is a bit wider than the stock one and will have to be trimmed if you are running a big fat SuperMoto wheel/tire.
Constructed of 3mm-thick (1/8"-thick) aluminum for heavy-duty, light-weight protection. Baseplate includes side protectors that wrap around the engine case to provide both bottom and side protection.
Have your tank cushions worn out over the years? Have you lost one or more while working on your bike? We have new upper and lower tank cushion rubbers.
This kit includes the original hardware, upper, and lower cushions.
Molded using a very durable, lightweight 1/8" thick polycarbonate - giving the windshield a high impact strength and making it shatter-resistant with a superior light transmission quality. Mounts quickly and easily onto the stock headlight cowling for a clean factory look. Drilling of the cowling is required, hardware is included. Removal for trail riding is also quick and easy.
The Strombone is the perfect solution for mounting a GPS unit to your V-Strom DL650 or DL1000. Designed for use with RAM Mounts mounting products (sold separately).
Manufactured from CNC machined 3/8" aluminum, it provides a stable platform and convenient location for your GPS unit, iPod, iPhone, Cell Phone, Camera or other electronic device with a 1" RAM Mount Ball.
The must-have accessory for adventure-touring. Greatly eases basic chain maintenance, tire changes, parking, and bike cleaning. Super-strong steel construction features typical German design and high engineering standards. Superb integration with the factory exhaust and side stand components - retain all existing features without sacrificing lean angle or clearances.
All hardware needed to mount the centerstand included. Typically installs using basic hand tools. No welding, cutting, or drilling of existing frame or body parts required. Tough black powdercoated finish with some gray fittings or hardware as applicable. A double-retention spring is included as a safety feature to prevent the centerstand from contacting pavement if one of the two springs should fail during a ride. Designed to work with OEM components -- we cannot assure fit with aftermarket exhausts or other accessories.
Constructed of a 4mm-thick aluminum base plate and 3mm-thick side plates for heavy-duty, light-weight protection. Where the base plates and side plates overlap, it forms a riveted 7mm-thick rail for extra rigidity. Base plate includes side protectors that wrap around the engine block to provide both bottom and side protection. Available in bare aluminum or powdercoated black for an extra $13.00.
Installation of the SW-Motech skidplate requires previous installation of the SW-MOTECH crashbars, which are sold separately.
The SW-Motech skidplate is not compatible with Givi or Hepco-Becker crashbars.
The SW-Motech skidplate can be used without a centerstand, or with the SW-Motech, Suzuki or Hepco-Becker* centerstand.
Constructed of heavy-duty mild steel, SW Motech crash bars are designed to provide maximum protection, optical integration, and high-quality fit and finish.
The new SW Motech Rally Crash bars feature a thicker tubing diameter than the previous guards, extend higher up on the side panels for more direct impact protection, and still work perfectly with the aluminum skid plate from SW Motech.
All components are protected against corrosion by sandblasting and black powder coat. Two high-strength frame mounting points.
The SW Motech skid plate is not compatible with Givi or Hepco-Becker crash bars.
Moose Racing's Heavy-Duty, 4mm thick 5052 aluminum, to protect expensive and fragile radiators from side impacts and twisting.
Make the installation as easy as possible with this Optional Connector Set. This allows you to put an OEM style connector on the Edge Taillight Circuit Board Upgrade making the connection simple. Stock plug will go right into this unit and off you go. You will need a crimp tool or set of needle nose pliers to crimp connectors on.
ProCycle's 14 gauge stainless steel case armor to protect your engine cases. These case guards bond to your clutch cover and stator cover with high-temp silicone (not included). Extremely tough protection from rocks. In a fall your brake pedal or shift lever can crack the engine case - leaving you stranded. Don't let it happen to you.
CNC machined from 2mm 5052 plate, these will protect your cases in the event of a bad spill. Mounted using a high-quality red silicone adhesive, which you can select as an Optional Add On so you can mount them up as soon as they arrive. Below is a link to Installation Instructions with photos to help you get them done properly.
Ease the pressure on your wrist during those long highway drones out to where the fun begins. ProCycle has developed this kit that includes a Vista-Cruise throttle lock, a specially modified alloy throttle tube and an anchor plate that attaches to your throttle housing. Just flip the thumb lever down to apply enough friction to hold the throttle in place. Use the supplied longer screw to attach the anchor plate to your lower throttle housing bolt hole. Also included is a tension adjustment tool that you can keep on your key ring. Keep the applied tension lightly adjusted so it's easy to roll the throttle off.
Fits bikes with dual cable throttle housings.
Sized perfectly for adult back-yard racing or fast/aggressive mini riders. This is the most important upgrade you can make for an adult sized rider. The stock suspension is too soft for most adults and aggressive kids. Fits stock shock.
Both kits include all bushings, snap rings, and washers.
Gen 2 kit also includes the necessary O-rings.
Gen 1 kits are OEM bushings, snap rings and washers.
Warp 9 Flex Levers are CNC machined from billet aluminum. These hinged levers also have adjustable reach that allows total customization to the rider's hand size. Double hinge design allows lever to flex out of the way in most impact situations.
Sargent's proprietary seat foam is their own unique blend of resilience, firmness, and vibration-absorption qualities - making it well suited for maximum long distance comfort. Available in standard height and 2" lower than stock.
Does not fit the the "C" (European) models.
The Warp9 oversized front brake rotor kit for the TW200 has amazing brake Performance. This high quality oversized rotor is laser-cut from high-carbon content 410 stainless steel then lap cross hatch ground and heat-treated. Finally, high-temp paint is applied to surfaces like cooling holes and edges to provide a clean, finished look.
Includes a billet caliper relocation bracket that is easy to install, and a fresh set of brake rotor bolts.
*Add the Galfer steel braided brake line for the ultimate braking performance.
The world’s best motorcycle Mesh & Bluetooth Communications System.
Features:
Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm. Lo-pegs are down and back 1/4".
Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm. Lo-pegs are down and back 1/4".
Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm. Lo-pegs are down and back 1/4".
The tension system integrated in this loop is a Green Chile innovation. Their elastics are custom woven inside tubular nylon webbing. This gives you all of the advantages of adding tension to a strap while maintaining the full strength of nylon webbing. You can add their cam buckle tension loop to any 1" flat webbing system and have an instant upgrade.
CONSTRUCTION FEATURES
Patent Pending
This Australian made radiator stone guard is machined from 4mm aluminium 5083 plate. The extra thickness of material provides superior strength and protection against larger debri as well as small rocks etc. Radiator guards can be fitted in approx ½ hr or less using basic tools.
All radiator guard mounting hardware is supplied where necessary.
This bash plate is made from 5mm aluminium 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider. All bash plates are supplied with the necessary stainless clamps and bolts where possible. All bash plates have a polished finish and have foam or rubber where required.
Australian made, this protector bolts to the stock caliper bracket.
This Australian made bash plate is made from 4mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider.
All bash plates are supplied with the necessary stainless clamps and bolts where possible. All bash plates have a polished finish and have foam or rubber where required.
Fits with SW Motech & Givi Crash bars.
B&B Off Roads KTM 950 & 990 Adventurer bash plate is made from 5mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider. All bash plates are supplied with the necessary stainless clamps and bolts where possible. All bash plates have a polished finish and have foam or rubber where required.
Protect your frame/paint from scuffs and scratches with frame guards. The CR80 & CR85 frame guards are made from 2mm 5052 marine grade alloy and CNC machined in one piece for strength. All frame guards are supplied with all necessary mountings and stainless bolts. With a polished finish they look great and are easy to install.
Standard Floating Wave® Rotor
Full floating to ensure optimum brake pad-to-rotor contact. Every high-quality, Galfer-patented Wave® rotor is made from a proprietary mix of virgin high carbon 420 stainless steel, laser cut (never stamped), double disc-parallel ground to assure perfect parallel flatness and heat treated to each specific application. KBA and TUV approved. Seamlessly replaces stock rotor. Full instructions provided along with any technical help needed.
The X-Grip is a frame guard that allows the rider to both protect the frame of the motorcycle from wear as well as adding more grip to the bike. Made from a dual injected mold; The outer plastic is durable polycarbonate while the inner plastic is durable yet playable and offers incredible grip.
Features:
Available in 2 colors
New for 2020, SpeedoDRD has been decreased in size to only 20mm square and epoxy sealed with weatherproof device connectors; making it the smallest, most durable, and most feature packed device on the market.
Note: The SpeedoDRD cannot alter your EXISTING odometer readout. The SpeedoDRD corrects and fixes the speed signal after it was altered by something else, such as sprocket changes or tires size changes or transmission changes.
T7 Solo Carry rack has been designed predominantly for the solo rider to keep loads as forward and low as possible. The plate has multiple attachment points making easy to tie down bags.
The plate is pre-drilled for mounting systems for both Givi monokey and Rotopax. The rack is light in weight only weighing 2.3kg.
This bash plate is made from 4mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider. All bash plates are supplied with the necessary stainless clamps and bolts where possible. All bash plates have a polished finish and have foam or rubber where required.
The long over-due rally shield for the 2008-on KLR650 is finally here!
Parabellum uses 4 steel brackets mounted to factory locations as well as our stand-off windshield design to ensure the customer doesn’t have to drill extra holes in the cowling but still achieves that iconic upright look of the real Dakar Rally bikes.
The Rally shield protects the rider’s torso/chest from air, cold, roost, branches and bushes while leaving the rider’s head/helmet in clean air. We recommend the Rally shield for riders seeking some protection, but prefer to be off-road.
The Rally shield is made from 1/8 inch cast acrylic and is 11.5 inches wide at the bottom and 17 inches tall.
Australian made, this protector bolts to the stock caliper bracket.
Protect your frame/paint from scuffs and scratches with frame guards. The CR 500 frame guards are made from 2mm 5052 marine grade alloy and CNC machined in one piece for strength.
All frame guards are supplied with all necessary mountings and stainless bolts. With a polished finish they look great and are easy to install.
This bash plate is made from 4mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider. All bash plates are supplied with the necessary stainless clamps and bolts where possible. All bash plates have a polished finish and have foam or rubber where required.
Cogent Dynamics has created another winner - the 'World's Edge' shock for the 650 V-Strom the rear end you have wanted for all these years. This unit gives the DL650 excellent control with a firm but comfortable ride, both solo and two-up. This shock is equipped with adjustable damping control so you can customize the action to your preference. Please call for lowering options also if you need them.
The Bling Ring preload adjuster and thrust bearing on the spring make preload changes easy when you fill the bags and add a copilot. Keeping the ride height up can make the difference between a good handling motorcycle and a peg scraping pig. Want to make it easier yet? Add a Hydraulic Preload Adjuster like the stock shock has.
Includes mounting bracket.
Bikes with ABS require the hydraulic preload adjuster
The features of this tool include 300 psi capacity, bleeder valve and T-handle plunger pin chuck. Swivel chuck has a 12" flexible hose. Comes complete with instructions, carrying box and Schrader valve extension (required on some Showa shocks). Nitrogen bottles available at any welding supply house.
This carry rack is solid and durable made from 5052 aluminum and with its sleek design it will not catch on your clothes or nature.
It is an easy install and will allow you to strap your cooler, lunch box, tools, or whatever on the back of your new Honda.
Comes complete with all hardware and easy install instructions.
Choose from powder coated or raw aluminum finish.
This is the ultimate in radiator guards! It will protect your fragile radiator from nasty front & side impacts.
This ultra tough guard is constructed from 1/8" aluminum and is easy to install.
All Flatland Racing radiator guards have rear mounting brackets for that extra support! All Mounting hardware is included.
Repair kit for your rear disc brake caliper.
Yoshimura has always been synonymous with quality craftsmanship, precision fitment, and impeccable quality. The Fender Eliminator Kits are no exception, and they are sure to give your motorcycle the sleek race look that every rider craves
Features:
Giant Loop Rubber Boa Straps confidently put the squeeze on a spare inner tube, tools, water, or other off-road essentials when strapped to dirt bike fenders. Stretch elastic shock cord with heavy-duty injection molded fender hooks. A simple locking slot applies dynamic tension to create a dead-solid connection between plastic fenders and relatively small, lightweight gear—even in demanding terrain.
Replace your motorcycle’s windscreen with PUIG’s touring windscreen. Manufactured in acrylic of 3-4 mm according to the motorcycle model to guarantee maximum protection from the wind, improving the aerodynamics of the piece and possible debris that may impact you during your ride.
In addition, it comes with a variable visor that will redirect the wind even more while achieving a great sense of comfort on board your machine. This visor is fixed to the touring windscreen by screws, since the screen comes with the holes already made to facilitate assembly.
The windshield has a rounded contour of> = 2mm, complying with the TÜV regulations.
This part is only available in smoked finish.
For assembly, PUIG provides instructions with mounting tips, so you can quickly enjoy the touring windscreen on your motorcycle.
Developed specifically for the rider who's looking for that classic scrambler style but still wants up-to-date performance and capability. The Bridgestone® AX41S Adventurecross Scrambler Tires are made to perform, while still retaining that modern, classic style.
FUNCTION:
TECHNOLOGY:
OTHER FEATURES:
PACKAGING & PARTS INCLUDED:
