Search Products

Rear wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.

Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.

Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.

Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.

Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.

The rubber coated outside diameter creates an optimum seal at the hub.

Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.

Includes all wheel bearings, new dust seals. The rear kit includes the bearing and seal for the cush drive hub (sprocket carrier). All bearings are sealed on both sides.

Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.

Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.

Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.

Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.

Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.

The rubber coated outside diameter creates an optimum seal at the hub.

Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.

This devices allows any two wire after market LED turn signal indicators to operate as running lights (always on), and will blink on / off when the turn signal switch is activated. It is highly recommended to use this product with the Fixed Rate Turn Signal Flasher. This device, as well as aftermarket turn signals, use much less current than stock turn signals, thus an increased flash rate will occur. Load resistors or a fixed rate turn signal flasher will get your flashers operating at the normal flash rate again.

Each package contains two separate adapter boxes, good for operating both turn signals, left and right of either the front OR rear of your motorcycle. You will need to purchase a 2nd kit if doing the Front AND Rear of the motorcycle.

This device is universal; designed to work for any motorcycle with a DC electrical system. Kit comes with bullet connectors to wire in manually. Works with any two wire non-sequential aftermarket LED turn signal indicators.

GBrakes Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.

The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.

• Significantly improves response and feel over factory rubber lines
• Largest performance improvement for your money over any other braking upgrade
• Stainless steel hose resists abrasion and puncture
• Teflon core does not degrade over time like rubber lines
• PTFE Dupont 64 Teflon® hose
• Feature a heavy-duty stiffener sleeve and route just like the factory lines
• Proprietary, premium fittings
• Banjos utilizes a unique machined channel and sealing surface for leak-free installations
• R&D and engineered in the USA
• GBrakes USA controls the manufacturing process, ensuring the highest level of quality control

GBrakes Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.

The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.

• Significantly improves response and feel over factory rubber lines
• Largest performance improvement for your money over any other braking upgrade
• Stainless steel hose resists abrasion and puncture
• Teflon core does not degrade over time like rubber lines
• PTFE Dupont 64 Teflon® hose
• Feature a heavy-duty stiffener sleeve and route just like the factory lines
• Proprietary, premium fittings
• Banjos utilizes a unique machined channel and sealing surface for leak-free installations
• R&D and engineered in the USA
• GBrakes USA controls the manufacturing process, ensuring the highest level of quality control

GBrakes Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.

The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.

• Significantly improves response and feel over factory rubber lines
• Largest performance improvement for your money over any other braking upgrade
• Stainless steel hose resists abrasion and puncture
• Teflon core does not degrade over time like rubber lines
• PTFE Dupont 64 Teflon® hose
• Feature a heavy-duty stiffener sleeve and route just like the factory lines
• Proprietary, premium fittings
• Banjos utilizes a unique machined channel and sealing surface for leak-free installations
• R&D and engineered in the USA
• GBrakes USA controls the manufacturing process, ensuring the highest level of quality control

Quality components at a great price.

• Standard Kit: Includes SS braided lines and EBC sintered brake pads.
• Standard Plus Kit: Includes SS braided lines, EBC sintered pads and an EBC Carbon Steel front rotor.
• Super Plus Kit: Includes SS braided lines, EBC sintered pads and EBC carbon steel front and rear rotors.
• Deluxe Kit: Includes SS braided lines, EBC sintered pads and an EBC Premium 320mm SM front rotor kit.
• Super Deluxe Kit: Includes SS braided lines, EBC sintered pads, an EBC Premium 320mm SM front rotor kit and EBC rear rotor.

SMX Carbon Look Rotor

• Rotor material has higher friction than plain stainless steel for added stopping power
• Rotors measure 320mm
• Come with caliper relocation bracket
• Designed to fit standard hubs

High quality carbon steel brake rotor.

A great option for every day use, or on your spare rear wheel.

• manufactured from unique ebc low carbon hpsr steel
• laser & cnc punched for lightness
• hardened and ground for precision braking
• nickel coated to resist corrosion

We offer two different types of SuperMoto tubes. The first are Standard Tubes and are meant to be used with standard bias-ply type tires, but can be used with radial tires also.

But, if you are running radial tires, like SuperMoto, or have a retro bikes with spoked wheels and radial tires, you probably want to run the 'Radial Tubes'. Front tubes fits 120/70 and 120/60 tires. Rear tubes fits 150/60, 150/70 and 160/60 tires. These have a metal valve stem.

The PowerBomb header promotes better flow by allowing a small expansion of the exhaust gasses. The 'bomb' also acts as a pre-muffler taking the edge off of overall sound levels.

Protect your head pipe from rock damage. This stainless steel spine clamps to your head pipe to add a layer of protective armor between your vulnerable pipe and those nasty rocks or logs. Fits the stock headpipe. Will fit the FMF head pipe with the addition of larger clamps.

Bradley performance bomb header for TW200. 

By positioning this “Bomb” at a key point in the system, increased performance and flow is achieved through the expansion and contraction of exhaust sonics through the system. The result is a flow increase of nearly 10%. 

The outer chamber in the Powerbomb allows the air to expand, cool and ramp back up at a higher velocity. 

Fits all years of TW200 and works with all other brands of mufflers. Stainless steel and nickel plated. A clamp-on shield can be added, sold separately.

The DG RST (Reduced Sound Technology) muffler is the quietest DG muffler and is designed especially for dual-sport machines (Just 84db @ 3200 RPM). A new baffle design dissipates sound waves reducing noise output in a very efficient manner. This new design also stretches out the time between muffler repacks. Included is a Stainless Steel mid-pipe, USFS Approved Spark Arrestor and a new Aluminum end cap.

For the frame drain on your XR650L ,extra protection for your motor! Strong magnet at the end of the plug picks up metallic flakes in your oil, protecting your engine!

Order up your new levers here! If you keep breaking levers, you might want to think about a set of hand guards to protect them in case of a fall.

For easy removal of recessed oil filters.

Conical point screws pierces and grabs the metal end cap of the filter.

Reduces potential damage to the engine cases.

NOT for use on re-usable oil filters.

Cat Crap is the #1 voted anti-fog on the market. Lens cleaner and anti-fog in one. Works for all lenses, eyewear, goggles, helmet visors, etc.

You’d be amazed at the dirt and debris that can work its way into your gas can – and from there, your fuel tank. Twin Air’s monofilament screen pocket inserts in your tank to catch particles as small as 40 microns (.00165”) while allowing the gas to flow freely. 

The flange is custom-sized for each modern 4-stroke model to ensure a leak-proof seal. Just remove the filter periodically, turn it inside-out, and clean out the debris that could have been in your engine.

Will not work with factory locking gas caps.

If you're like us, you hate the long floppy vent hose hanging off the cap of your aftermarket tank.

This one-way vent cap replaces the long hose with a short one only about 2" long. It allows air into your tank but prevents fuel from sloshing out.

Machined from billet alloy and anodized for good looks.

  Not for stock fuel tanks!

Got a little oil seepage or changing out your clutch pack? Here is the gasket you need for the right hand side case cover of your TW200. This is the same side of the engine as your kickstart lever and/or rear brake lever.

These versatile Risers allow you to clamp a 7/8" diameter handlebar or you can remove the 7/8" reducers and then clamp an 1- 1/8" aluminum "fatbar". If you are thinking of going to a fatbar after you bend your stock set or just want the versatility and option to run any bar, this is the riser to go with. Reducers lock into risers to insure no slippage between components.

These risers use 8mm bolts. Always check and confirm that your bike has adequate cable and brake line length before installing any handlebar risers.

Anti-Vibration Risers may interfere with aftermarket large capacity fuel tanks, and some steering stem clamp configurations (in these cases we recommend using standard pivoting risers).

• 4.75" wide,
• Raises handlebars 2 inches and allows fore/aft position adjustment
• Provides dual pivot points for optimal bar positioning
• One piece design is made from solid aluminum for superior strength
• Available for 7/8" - 7/8" or 7/8" - 1 1/8" bars

Requires 7/8" factory bar clamps on bike

• Adapt 7/8" bar mounts to accept oversized 1-1/8" handlebars
• An economical alternative to replacing expensive top triple clamps
• Include mounting bolts.

A high quality replacement clutch cable.

Replacement shift lever with folding tip.

Replace the soft stock lever with sturdy forged aluminum.

Folding tip prevents snagging.

Hardened splines won't slip or rotate.

Replacement folding shift lever, stock length made by IMS.

This bar kit will raise your hands 5.5" up from the factory riding position. If you are over 6 feet tall, this is the kit for you! It allows for a more natural riding position, no more bent neck and being hunched over the bars. You will be able to ride comfortably and more aggressively by installing this kit.

The ProTaper bars are taller and tapered from 1 1/8" to 7/8" and the braided stainless steel brake line will be a serious improvement to your braking ability. Braking becomes more responsive and firmer while adding a stylish look to your TW200.

Everything you need is in this kit to properly raise your bars:

• ProTaper ADV High handlebar
• PowerMadd 2" bar riser
• Harness extensions
• Longer braided steel brake line
• Longer clutch cable

Say goodbye to the frustration of fidgety handguard expansion plugs with Warp 9's innovative Tapped Handlebars. 

These handlebars feature ends that are plugged and tapped with an M8x1.25 threaded insert, providing a secure and reliable mounting point for all aftermarket wrap-around handguards. 

No more worrying about plugs pulling out or spinning during crashes; their robust design ensures you're good to go, even when you encounter obstacles. 

Not using handguards? No problem they've got you covered!Each set of handlebars comes with aluminum grip guards and stainless bolts, offering protection for your grips and delicate throttle tube in case of a get-off. 

Designed with an oversized 1-1/8 inch (28.6mm) clamping diameter that tapers down to 7/8 inch (22.2mm) to accommodate standard controls. Crafted from 7010 T6 aluminum tubing and featuring computer-extruded variable wall thickness, they effectively reduce vibration while enhancing overall performance and comfort. 

Note: Does not include pictured bar mounts.

Motocross brake rotor featuring ultra lightweight radically profiled contours for great looks, great self cleaning and brake performance. Made with tough and durable heat treated stainless steel. Heat treated to perfection and then diamond ground to micron accurate surface finish and parallelism and will deliver great brakes that perform well and last.

RotoPax are Rotational Molded - the process which produces indisputably superior products.

• Thicker walls and stronger construction
• Bright colors that are less prone to fading
• Extra threads, thicker walls, and sure-seal gasket guarantee no leaks

Need to mount two containers? A water and a fuel? Two waters? Finally, you can stack multiple packs together! Use in conjunction with a pack mount. You will need to purchase the Single Mount as well as the Extender.

RotoPax holder made to mount a single Fuel and/or Water container.

Need to mount two containers? A water and a fuel? Two waters? Get the extender which allows you to stack two containers no problem! Single mount, two containers

High Quality chain. You'll need to cut to fit your sprocket combination.

Stabilizes gas for short and long term periods of inactivity (up to two years) while preventing the formation of varnish. Eliminates carbon buildup in fuel delivery system and exhaust components. Increases octane and removes water from the fuel, making it the perfect solution to prevent and eliminate ethanol (E-10) fuel problems. 8 oz bottle treats 48 gallons of fuel.

• Cures and prevents ethanol fuel problems
• Helps prevent phase separation
• Makes engines start easily, run smooth

Their rear racks are great for adding the extra storage needed for your next adventure. They are the perfect size for a backpack or small duffel bag. Their steel racks are built to handle any riding style you throw at them, now Rotopax ready! This is the ENDURO Series CRF300L rear rack which measures 10 inches wide and 12 inches long.

Easy to Install

• Works great for mounting Pelican and Seahorse cases, or any other hard case. Givi compatible.
• Holes are in place to accept Rotopax mount with no drilling required.
• Stainless steel mounting hardware and instructions included.
• Fabricated with mild steel, MIG welded, and finished with a semi gloss black industrial grade powder coat.
• Weighs 3 lbs, 10 inches wide, 12 inches long.
• Works with stock tool bag. You can remove the seat with no interference from the luggage rack.
• Rear rack only, no Rotopax mount or side racks included.

PMR side utility racks are great for strapping down your soft luggage and keeping it off the rear plastics and exhaust pipe, while adding plenty of new tie down points for any luggage you have on your seat or tail section. They also add an enhanced level of security and strength to the rear end of your motorcycle in the event of a tip over or crash. 

Sold as a pair.  Easy to Install

• Complete with all necessary mounting hardware
• Fabricated with 1/2 inch steel tubing, MIG welded
• Finished with a semi gloss black industrial grade powder coat
• Comes with left and right side racks, each side weighs 2 lbs
• The TW200 side racks are intended to work hand in hand with our ENDURO Series rear rack.

A precision fabricated bolt-on swingarm extension for the TW200.

This kit provides a 3” stretch without having to cut and weld your motorcycle. Heavy duty steel construction with a silver metallic powder coated finish.

This complete kit includes everything you'll need: mounting hardware, brake linkage extension, and a new longer 428x136L non o-ring chain.

Provides additional clearance for running larger ATV tires.

Race Tech HP Springs have a high stiffness-to-mass ratio. In other words; the springs are light weight for their particular spring rate. This requires the finest materials and processing. Shot-peened and pre-set so they cannot sack out. All Race Tech HP Springs have the highest rate tolerances in the industry. These are the finest springs in the world-guaranteed.

This spring is 8.0kg/mm

OEM spring rates are 5.7-7.6kg/mm progressive style.

Dust/waterproof synthetic/petroleum blend for foam-type air filter elements. Super-tacky polymer and co-polymer additives hold onto virtually all fine particles.

• 4-12% increased airflow over competitive products
• Will not plug or migrate off of filters
• Resists washout from carburetor fogging
• Dyed dark blue to ensure even coverage
• Made in the U.S.A.

Their rear racks are great for adding the extra storage needed for your next adventure. They are the perfect size for a backpack or small duffel bag. Their steel racks are built to handle any riding style you throw at them, now Rotopax ready! This is the ENDURO Series KLX230 rear rack which measures 10 inches wide and 12 inches long.

Easy to Install

• Works great for mounting Pelican and Seahorse cases, or any other hard case. Givi compatible.
• Holes are in place to accept Rotopax mount with no drilling required.
• Stainless steel mounting hardware and instructions included.
• Fabricated with mild steel, MIG welded, and finished with a semi gloss black industrial grade powder coat.
• Weighs 3 lbs, 10 inches wide, 12 inches long.
• Works with stock tool bag. This requires an extra hardware kit available for free by request only.
• Rear rack only, no Rotopax mount or side racks included.

Plug-In connector kit for your CRF. This kit fits Rally and Non-Rally Versions of the Motorcycle. Wires and terminals will come pre-attached with subharness.  

Plugs into the Aux Power connector. 
Harness length is 32" (2.66ft)