GoldPlug is the gold standard in engine protection.
Stainless steel drain plug with an extremely strong magnet that picks up metal flakes in your oil.
10MM Thread
GoldPlug is the gold standard in engine protection.
Stainless steel drain plug with an extremely strong magnet that picks up metal flakes in your oil.
10MM Thread for frame drain.
This kit of O.E. Suzuki O-rings replaces your leaky, weepy, and brittle O-rings that fit between your DR's oil cooler lines. You get 4 O-rings in this kit to replace both feed and return line O-rings.
If you're noticing oil leaking or creeping around your oil cooler, oil cooler lines, or engine, you may have one or more failed / failing oil cooler line O-rings. Replace them now before they completely fail and you run your motor dry of the precious oil it needs to operate properly.
In this kit you will get 4 factory replacement bolts to replace any broken or damaged clutch pressure plate bolts on your DR650.
It can be easy to over torque these bolts if not done properly. If one of these bolts is damaged on your DR650, we highly recommend replacing all 4 to prevent any future failures down the trail.
We strongly recommend checking valve to piston clearance when installing a non-standard camshaft.
What would you do if your oil cooler was damaged way out in the bush? We have a simple solution. This kit allows you to bypass the oil cooler and both oil lines and insure that the top end continues to get the oil it needs to stay healthy. Simply remove the stock oil lines from the motor and attach one end of the bypass at the head and the other end at the engine side case. Be sure to leave the original o-rings in place.
Small, light weight and easy to carry. You may never need it but if you do it will save you a lot of walking!
The X-Grip is a frame guard that allows the rider to both protect the frame of the motorcycle from wear as well as adding more grip to the bike. Made from a dual injected mold; The outer plastic is durable polycarbonate while the inner plastic is durable yet playable and offers incredible grip.
Features:
Available in 2 colors
Frame Guards protect the frame from wear helping to keep your frame looking new. Mounting hardware is included for quick and easy installation.
The X-Grip is a frame guard that allows the rider to both protect the frame of the motorcycle from wear as well as adding more grip to the bike. Made from a dual injected mold; The outer plastic is durable polycarbonate while the inner plastic is durable yet playable and offers incredible grip.
Features:
Protect your motorcycle’s levers from damage during an impact with the solid protection offered by Barkbusters aluminum bar lever protection handguards. Constructed with solid heat treated aluminum backbones these hand protectors use a two point mounting system that provides strength to withstand plenty of force. Motorcycle handguards by Barkbusters with their full wrap design will help keep your levers operational and your ride from coming to a premature end in the event of a drop or other mishap.
Features:
Add Plastic Handguards for a complete kit.
Please Note: This aluminum bar handguard kit requires the removal of original external and internal bar weights on '19-Current models. This will leave a hollow handlebar for mounting the handguard.
It may not surprise you that they are covered with HippoSkin™, their waterproof outer shell, and insulated with a generous layer of HippoFat™, a warm, flexible, closed cell foam insulation—both are designed to keep inclement weather away from your hands.
Sold in pairs.
Hand/brush guards are required for proper fitment and for safety reasons.
Hippo Hands go on and off in seconds and never require tools or hardware.
The Backcountry is 9" deep.
If you like to stand and ride, this is the model for you! But… these hand covers also fit to just about any bike. They are also a great option for cruisers with hand guards or lever guards.
They feature a durable, quilted interior and flexible, neoprene cuff which ensures a great fit on so many bikes. The Backcountry is their smallest, most easily adaptable hand cover.
The Backcountry features a front reflective panel for higher visibility in low light situations.
Galfer USA produces several different brake pad compounds for all types of riding styles and uses. With over 60 years of friction material production and research, they have learned that one compound doesn’t always do the trick across the board. If you are just looking for an OEM brake pad replacement or a high performance race brake pad, they have you covered!
Set includes front and rear brake pads.
Semi-Metallic Compound
OEM replacement upgrade. Great feel, long lasting, and very little rotor wear with this durable compound. Compound applications for almost every need, including off road, street, touring, enduro, dual sport and more. Precision made in our Galfer factory in Spain.
Best Use: Our most popular compound! This compound is the work horse of the Galfer family and is a great OEM upgrade for the everyday rider.
Direct replacement OEM front brake cable for TW200 with drum brakes.
Factory Honda replacement for your worn out lower cable guide.
Each kit includes all necessary rubber components and brake pins.
Special tool to remove the flywheel from the end of the crankshaft.
Our own jet kit for the Mikuni TM40 carburetor.
Includes new main jets, pilot jets and a new needle with e-clip.
Comes with a printed Mikuni tuning manual and a jetting suggestion chart.
Not for the stock carburetor Fits TM40 conversions Only
This seal helps keep debris and water out of your DR650 air box and it may become damaged or missing over the years. It is an important part of your DR650's intake system to maintain & prolong air filter life.
Simply, remove the air box door, then remove the old seal and clean out the track it sat in. Set the new seal in place and cut off any excess material remaining. Install the air box door and you are done.
FunnelWeb ProLine Filter Highlights:
Like all FunnelWeb filters, the ProLine Filter features profile cut, single layer, single density foam that doubles the external surface area of the filter without increasing the original filter size. The ProLine Filter traps dirt, dust, sand and mud over a larger area on its outer surface, ensuring optimal air flow is maintained for maximized engine performance and reliability.
The single layer, single density polyurethane foam has the added advantage of being easy to clean and the ability to maintain its original shape after numerous washes. Overall, compared with conventional foam filters, FunnelWeb offers more protection from dirt ingestion, has longer service intervals and maintains high airflow rates when dirty.
FunnelWeb ProLine Filter Highlights:
Like all FunnelWeb filters, the ProLine Filter features profile cut, single layer, single density foam that doubles the external surface area of the filter without increasing the original filter size. The ProLine Filter traps dirt, dust, sand and mud over a larger area on its outer surface, ensuring optimal air flow is maintained for maximized engine performance and reliability.
The single layer, single density polyurethane foam has the added advantage of being easy to clean and the ability to maintain its original shape after numerous washes. Overall, compared with conventional foam filters, FunnelWeb offers more protection from dirt ingestion, has longer service intervals and maintains high airflow rates when dirty.
These Mikuni carburetors are correctly sized and easily fitted to your Honda XR600 and XR650L stock motor mounting flange after removing the locator tags and also match the air box when using the silver anodized air-box adapter. This adapter is fitted prior to delivery when purchasing complete kits. For this Mikuni carburetor to operate correctly the motorcycles air box must be opened up to allow more air flow in. Using a hole saw, a 45mm diameter hole will be sufficient for a Suzuki DR650 but some Honda’s require way more. The best process is to keep opening up the air-box until no more improvement is noticed and you will be surprised at the difference. The kit also comes with throttle cables and a 1/4 turn quick action throttle which must be lubed before fitment. The carb comes with a couple of Honda specific adjustments made and pre jetted for your engine. A specially made size 30 pump nozzle is fitted as the accelerator pump circuit on TM42 carbs will not work properly on Honda’s or Kawasaki’s without it.
Climate, altitude and fuel density from different octane fuels all have varying effects on final fine tuning as does cam, exhaust and cylinder head porting etc. For this reason, we have included what we have found to be a range of jets to allow you to tune to most variables.
This carb fits with most aftermarket large capacity tanks. Some larger capacity tanks do not allow the fitment of this carb without modification. A competent person can easily heat and depress the contact area around the throttle mechanism allowing for clearance on problem tanks. Polyethylene tanks start their life as lump of poly that when melted evenly spreads itself around a rotating mold, to later carefully heat with a heat gun any section of a tank and change the shape has no effect on the integrity of the poly itself unless pushed too far, thinning it. We recommend having this professionally done for the reason some people may neglect to properly remove all the fuel from an existing tank or if not competent may make a mess of it.
Custom made push/pull cable set for the Honda XR650L.
These are for use with the stock throttle assembly, when mounting a Mikuni push/pull pumper carb, or Keihin FCR series carburetor.
Available as +3" and +6" over stock length, with stock style throttle side fittings.
Sold in a set as shown.
Here's a set of Shorty brake and clutch levers for your 2001 and newer Tdub.
Introducing the Zeta solid bushings to replace your worn out rubber bushings. We have tested these bushings on our own bike and we love them. No more sloppy handle bars. Plus, they add a little bling factor to your bike! Simply unbolt your bar mounts and swap the rubber bushings with these anodized billet bushings for a more stable handlebar feel.
Features:
Canyon Dual Sport saddle is designed specifically to provide long range comfort for your Tenere 700. We also offer a Bench style saddle that provides more freedom of movement for you that leans towards off-road riding.
Their high density Comfort Cell foam allows a sleek profile, while providing a firm supportive ride that lasts. Rider seating is ergonomically shaped to fit the curve of your body and provide better weight distribution. This also helps to eliminate the centralized pressure felt from the stock seat. In the nose area, they sculpt the saddle narrow to allow for good ground reach. Canyon Dual Sport has a seat height between the Yamaha Rally seat and Yamaha Low seat.
Passenger seating area is designed with a neutralized platform to curb sliding forward in the saddle. Dished shaping provides an excellent contact patch while maintaining a clean look. For the best combination of looks and support, add the Ovalbac backrest shown. This backrest provides a generous, contact patch for excellent support. Angle adjustment is simple and can be performed without removing the saddle or backrest from the bike.
For an added luxurious touch, this saddle is available with the option of electric seat heaters. With the flip of a conveniently located switch built into the left side of the saddle, both the rider and passenger seating platforms will heat up and maintain temperature automatically. Simple to install with just a pigtail wiring to your bike's fusebox. All other components are built into the saddle and come preinstalled.
The design shown above includes Black Carbon-Fiber leather seating with Matte Black vinyl contrasting sides and a tasteful color coordinated Smoke Gray welt.
The default cover choices are black 'carbon fiber' on top and 'asphalt' on the sides, 'no welts', black logo. You can view all of the available materials and colors through the link below. If you would like your seat built with something other than the standard choices please state specifics in the comments during check out.
This Comfort XL seat design is roughly 3" wider overall than their standard comfort seat. This means more surface area, better weight distribution, and added comfort for those not worried about seat width.
Available as Complete Seat only. The Complete Seats come assembled with an aftermarket pan and ready to ride.
| Width: | 11" (279mm) |
| Height: | Same as OEM |
Seat Concepts seats are constructed using a foam material that is higher quality than OEM seat foam. Their proprietary formula is plush, while still offering the necessary amount of support. Their unique comfort and shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.
These great features combine to offer you a custom seat feel, and provide greater enjoyment and increased range for long commutes, or Dual-Sport rides!
The Complete Seats come assembled with an high quslity aftermarket pan and ready to ride.
| Width: | 12 5/8" (321mm) |
| Height: | Same as OEM |
The Commuter seat maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but has a dished seating position towards the mid-point to distribute rider weight over a greater area. This dished area is also wider than the stock seat to increase support. The passenger platform is the stock shape.
The Commuter seat is the best choice for extended pavement riding and mellow offroad. The unique shape and added width will provide greater enjoyment and increased range on a long commute, or Dual-Sport ride!
Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a more plush and active ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.
These features combine to offer a custom seat feel, and provide greater enjoyment and increased range.
Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!
Available as a Foam and Cover Kit for OEM pan. It DOES NOT include the pan.
| Width: | 8" (widest point located in the rear seating area) |
| Height: | Same as OEM |
| Width: | 8" (widest point located in the rear seating area) |
| Height: | 1" (25mm) Taller than stock |
Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a more plush and active ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.
Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!
These features combine to offer a custom seat feel, and provide greater enjoyment and increased range on a long commute, or Dual-Sport ride!
Carbon Fiber Sides/ Gripper Top
Available as a Foam and Cover Kit for OEM pan. It DOES NOT include the pan.
| Width: | 10" (254mm) |
| Height: | Same as OEM |
Individual 14T, 15T or 16T front sprockets.
JT Sprockets are made from the latest generation of computer design and control metal cutting equipment for maximum durability. Front sprockets are made from chromoly SCM420 steel alloy. All sprockets are heat-treated and hand-finished to meet or exceed the highest possible quality standards.
FRITZCO front sprockets are a straight up no hassle installation. Their sprockets are machined from alloy steel that in every way is comparable to OEM Yamaha and the best offered by other manufactures. The sprockets are then given a heat treatment that provides a compatible sprocket for the Yamaha output shaft and longest chain wear life possible.
Replacement retainer if yours is worn out or lost.
This retainer is has a no hassle installation for quick change sprocket swaps with simple readily available tools (pliers and screw driver).
This spring clip retainer takes the place of the OEM two bolt retainer and fasteners when a FRITZCO sprocket is used.
All sizes of new FRITZCO sprockets come with a quick change retainer included, this is only a replacement.
This retainer can only be used with FRITZCO sprockets and can not be used with thin OEM type sprockets.
ProCycle Dashboard designed to power multiple electronic devices. It can also be used for accessory lights, heated grips or gear, whatever you like.
The dash panel is manufactured from laser cut 5/64 mild steel and powder coated black. Also included are 2 weather resistant green LED rocker switches, a voltmeter with (two) 2.1 amp weather resistant USB ports, a wiring harness with a built in fuse/holder, and complete instructions. Everything you need to mount it and connect the bikes electrical system.
Spare Extension Cable Set for Shorai 12V LFX battery charger.
You can charge your Shorai battery with a regular battery charger but, if you want the very best for it this charger is designed for optimum performance by balancing the individual cells in the battery. Balanced charging ensures the battery reaches its fullest capacity and longest life. 'Store' mode allows long term maintenance storage.
Shorai Charge/Store Dedicated Battery Management System for Shorai LFX only. 2A Max charge rate, connects via BMS 5-pin port on LFX batteries. Includes modes for full charge, or long-term storage. Input USA 110~120V 50/60 Hz.
For Shorai Lithium Iron batteries only
Store mode not recommended for new LFM batteries with internal battery management system. See "Shorai Battery Charging" for more information.
The LITHIUM US is an advanced microprocessor-controlled charger specially designed to recharge and maintain the cells of Lithium-Iron (LiFePO4) batteries – maximizing their performance and lifespan. With up to 4.3A of charge current available the LITHIUM US is extremely flexible and will charge LiFePO4 batteries from 5Ah to 60Ah and maintain up to 120Ah.
The operation is simple and charging will commence upon connection. With no need to disconnect the battery from the vehicle, the LITHIUM US will automatically reset any low voltage protection electronics (Battery Management System) fitted. Charging can be restarted manually at any time using the ‘Reset’ button.
The CTEK LITHIUM US is a fully automatic ‘connect and forget’ charger with 8 charging steps including a testing sequence to show if the LiFePO4 battery can take and retain the charge, a unique maximization step to restore full capacity, and patented maintenance charging to ensure maximum performance even after months of inactivity. Splash-proof and dust-proof (IP65) the LITHIUM US is easy and safe to use, protects vehicle electronics, is spark-free, is reverse polarity protected and short circuit proof. The LITHIUM US features a 5-year warranty.
The CTEK Brand of chargers is recommended for all Antigravity RE-START (RS) Batteries (models with built-in jump-starting and full BMS protections)
New Hot Shot Suzuki Stator: aftermarket stator is made with heavy duty components and is a direct replacement for OE# 32101-32E01 or 32101-32E00.
This stator will provide your bike with 20% more power to support your added gear. Whether you have heated grips or you're running multiple aux lights, this unit will give you the power that you're looking for.
The ultimate factory activated lead-acid battery upgrade from stock.
40% more amp-hour capacity and 70% more cold cranking amps (230) than the stock battery. This is a genuine YUASA battery. Lasts longer and has increased vibration resistance. Ships pre-filled, sealed, and ready for use.
Note: This battery is taller than stock. The factory battery strap cannot be used to secure it. Factory-activated batteries should be charged once a month when not in service.
Dimensions: 6" x 3-7/16" x 4-3/8"
Weight: 8.5lb
12V/11.2AH 230cca
Positive terminal location: Left Front
Built with the latest in Lithium Ion Polymer Technology. All components are designed, manufactured, assembled and packed in one location assuring high quality and consistency. Besides extreme lightweight (50% to 70% lighter than standard lead-acid batteries) it also features a built-in LED test gauge and the ability to mount it in any position.
The Firepower features increased cranking amps over lead acid batteries and has a very fast recharge cycle, and can be brought up to a 90% charge within 6 minutes. It also has 6 to 12 times more cycle life when compared to lead acid batteries. A 2-year warranty insures that your investment is protected.
165 CCA 12V/36WH
Package Dimensions: 6.20 x 3.70 x 4.45
Ditch the stock ugly plastic sub-fender and install a B&B Off Road Engineering License Plate Holder. Comes with an LED light to keep the license plate lit up.
Rear fender carry all rack by Flatland Racing
This carry rack is solid and durable made from 5052 aluminum and with its sleek design it will not catch on your clothes or nature.
It is an easy install and will allow you to strap your cooler, lunch box, tools, or whatever on the back of your Honda.
Comes complete with all hardware and easy install instructions.
B&B Off Road's Honda Africa Twin Adventure Sport Big tour combo Luggage Rack has a two-piece main luggage plate with an added extension plate that mounts directly to the main rear rack and grab rails. Requires no modification for mounting.
Main luggage, adapter mounting plate and extension are all made from 5mm aluminum 5083 structural plate.
Very quick installation and can be done in a matter of minutes. The adapter plate is threaded for an easy install and removal of luggage plate which also includes mounting locations of our extension plate. Extension plate has some cnc machined billet clamps used for mounting.
Extension plates are great for those wanting to carry a larger load for a weekend trip or even to distribute some of the weight further forward
All the necessary bolts and brackets are supplied for mounting.
Rotopax and Givi Monokey holes are pre-drilled to suit the required mounts.
Total Width Maxi Plate Approx 45cm, Width of flat surface Maxi Plate approx 40cm
Total Length Approx 33cm
The Honda Maxi Luggage Rack and extension is made from 5mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider. All Carry/Luggage Racks are supplied with the necessary stainless clamps and bolts where possible.
DIMENSIONS
Maxi Plate:
Total Width Approx 45cm, Width of flat surface approx 40cm
Total Length Approx 33cm, Length of flat surface approx 33cm
Extension Plate :
Total Width: Extension Plate Approx 46cm
Will not fit adventure sports model. Please see other listing.
A sturdy and compact tail rack formed from 1 piece of structural 5mm thick alloy plate. Mounting utilizes the rear factory mount and their hidden sub-frame mount bracket.
Please note a small notch on the inner black plastic guard is needed to mount bracket.
The rack comes pre-threaded for optional luggage plate attachment.
Designed to make your compact rack even more versatile for riders who need a larger luggage platform.
ADD-ON
Pillion handles designed for quick and easy removal.
Using the included steel bracket to create 2 forward mounting points, this XT250 rack design is stronger and more well balanced than the typical "plate on the rear fender" design offered by other companies.
Their rear racks are great for adding the extra storage needed for your next adventure. They are the perfect size for a backpack or small duffel bag. Their steel racks are built to handle any riding style you throw at them, now Rotopax ready! This is the ENDURO Series XT250 rear rack which measures 10 inches wide and 12 inches long.
Easy to Install
A durable, lightweight option for your TW200 when transporting flexible luggage on the trail.
Whether it’s a quick over-nighter, a multi-day adventure, or commuting to your 9-5 … the OBR ADV Gear Explorer Saddlebag will get you to where you’re going while keeping your gear easily accessible, organized and protected from the elements. Removable roll down dry bags with ample amounts of capacity ride securely within a padded compression holster system making the OBR ADV Gear Explorer Saddlebag the bag of choice for the hardiest of commuters and adventurers.
Features
Moose Racing has just released a new set of rackless saddlebags in their ADV1 line up. These saddlebags come with a base panel that allows you to mount the bags in multiple positions to accommodate different side panels designs. These are different than the traditional ADV1 dry roll-up style as there is a shielded zipper, but they are made of the same tarpaulin material, this makes them strongly water resistant and rugged.
Replacement muffler hanger strap for your SS1 muffler.
This gasket seals the joint between the head pipe and Exhaust port. These gaskets are designed to crush a little bit to tightly seal where the pipe fits to the head. Get a fresh one now avoid having an exhaust leak when you install your new exhaust.
Did you snap a headpipe bolt on your XRL or are your headpipe bolts looking a bit dingy and rusty?
These replacement header exhaust stud bolts are made of super corrosion resistant 316 stainless steel. They provide excellent resistance to chemicals and saltwater to give your exhaust system a hassle free service life.
If you've got an older XR650L, you know the struggle of removing the O.E. nuts from the studs. They either snap, remove the stud or come off as they should. At some point you're likely to snap on or come across a seized nut to stud. These bolts are a superior upgrade to the O.E. nut and stud.
Kit includes: 4 Stainless Steel bolts
This Diode Kit is only necessary if you have a single dash indicator for your turn signals. One dash light for both left and right signals (such as on the DR650).
This kit allows power to flow in just one direction from the LED signals to the dash indicator light regardless of which direction you are signalling.
When upgrading your Suzuki DR650 with LED turn signals, it's required to install a diode module to prevent all of the signals from blinking at once regardless of left or right signal activation. Some riders choose to splice and solder their own solution, but we like things plug and play. That means all you have to do is plug in the TST kit and you're done! There's no need to cut or splice your OEM wiring harness or break out the soldering iron and electrical tape.
If you just installed aftermarket LED turn signals or an LED integrated tail light and your turn signals are flashing way too fast, or perhaps simply staying on completely, you're at the right place to find the solution! The TST Gen2-SK LED Flasher Relay fixes what we call "hyperflash". It slows the flash rate down to a pre-set 85 cycles per minute but can be sped up or slowed down using the adjustment dial located within the unit so you can get the exact speed you are looking for. The plug-and-play installation means that you don't need to splice in any load balancing resistors that generate unnecessary heat and require splicing into your stock wires. Simply remove the stock relay and install your new TST relay and your wiring job is done. It's that simple!
Please make sure your bike uses a 2-pin relay for the signaling system. If your bike has hazard lights it may need the 4-pin relay. Please also note the pin configuration and make sure it matches what is on your bike. It is very important to verify fitment before making your purchase.
The 250 taillight & brake light fits perfectly into the pocket from the stock DR650 taillight on the rear fender. Smaller and much better looking than the original.
Totally 'plug-n-play', includes a standard bulb installed or purchase an LED replacement, sold separate, for even brighter braking. The wire pigtail plugs directly into the DR650 harness just like stock.
Does not fit with the ProCycle Fender
This is the ultimate headlight upgrade for your XT250! It’s a plug & play kit which includes the newly released Morimoto round headlight with preassembled aim adjustable mounting bracket set. Installation takes five minutes and the light output is phenomenal.
Low Beam: 2,400 Lumens, 20 Watts
High Beam: 4,300 Lumens, 35 Watts
Color Temperature: 5,000K
Warranty: 5 Years
Modern LED technology with a classic look!
This plug & play kit is built around the all new Holley RetroBright LED headlight which comes in three different colors.
Choose from Classic White (3,000K), Modern White (5,700K), and Euro Yellow. The RetroBright also features a replaceable bulb.
Low Beam: 25W, 2,000 Lumens
High Beam: 30W, 3,000 Lumens
Color Temperature: 3,000k or 5,700k
DOT Compliant
Beam Pattern: Left Hand Drive (USA)
Modern LED technology with a classic look!
This plug & play kit is built around the all new Holley RetroBright LED headlight which comes in three different colors.
Choose from Classic White (3,000K), Modern White (5,700K), and Euro Yellow. The RetroBright also features a replaceable bulb.
Low Beam: 25W, 2,000 Lumens
High Beam: 30W, 3,000 Lumens
Color Temperature: 3,000k or 5,700k
DOT Compliant
Beam Pattern: Left Hand Drive (USA)
Does not fit '87 TW200 because that year has a unique AC powered headlight circuit.
Included in this kit are fork springs, Cogent DDC (Drop in Damper Cartridge) performance cartridges and one bottle of 5w fork oil. Refresh those tired old forks and make them better than new. These DDCs from Cogent are easy to install. No taking the forks apart, no drilling of the damping rods, nothing. Just take them off, flip them over to drain the oil, add new 5w oil, drop in the DDCs and then add the springs.
This upgrade offers better control off-road as well as on. Less brake dive keeps the fork up in the middle of the stroke on-road and better control off-road whether it be rolling water bars or bouncing off the rocks.
Stock Spring Rate is .50 kg/mm. The .60 kg/mm springs are 20% stiffer than stock while the .70 kg/mm is 40% stiffer than stock.
DDC Tool will not work with this spring series
The Cogent Dynamics DDC valves are the most cost-effective upgrade you can make to your motorcycle’s forks. Unique and the first of its kind, a DDC kit is available to upgrade many motorcycles that are originally equipped with simple damper rod type forks as front suspension.
We do recommend stiffer than stock front springs to bring the full potential of the DDCs out. OEM springs are dual rate 0.45/0.55 kg.
These Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. These units have been given the seal of approval by the ProCycle staff for both performance and ease of installation. No disassembly of your forks, no drilling of damper rods. Just change the oil over to 5w and install the DDCs under the springs and hit the trails.
DDC Tool will not work with this spring series
Patented fork seal features a balanced 3 lip design that evenly distributes the pressure reducing operating temperature, wear and friction
Custom Elastomer Fork Seals have been tested to outlast OEM fork seals. Extends typical seal life by 3 to 5 times over OEM seals
Stiction (friction) measures from 1/3 to 1/2 less than OEM seals for smoother fork action
Lower Stiction, Longer Life! It doesn’t get any better than this!
Plus, the only complete line of dust wipers! Wipers should be replaced with the fork seals to assure peak performance.
Kit includes Fork Seals and dust wipers.
License plate bolt with bright white LED light. The simple way to light up your plate.
A versatile performer with a tough nylon carcass and raised dimpled knobs that work well in a variety of terrain.
Features:
Voyager Pro, The Connected Rider’s GPS. Trail Tech offers a variety of model specific and universal kits for complete vehicle integration. All kits include mounting hardware, tach sensor, and power connection. Temperature and wheel sensors vary by kit, see kit contents for details. Adventure Begins Here!
Trail Tech provides a one year warranty and unlimited free phone and email support.
Designed to enhance the appearance of your motorcycle, yet provide greater riding distance per tankful. Larger capacity than stock, yet very slim and sleek. Perfect for wherever your adventure takes you! This tank is made from POLYETHYLENE CROSSLINK for extra strength and durability.
DOES NOT FIT NEW KLX300 "R" Models
Services two Pivot Pegz and fits MK2, MK3 and MK4 Pivot Pegz
Kit Contents:
Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm. Lo-pegs are down and back 1/4".
Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm. Lo-pegs are down and back 1/4".
Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm. Lo-pegs are down and back 1/4".
Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm. Lo-pegs are down and back 1/4".
Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm. Lo-pegs are down and back 1/4".
Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm. Lo-pegs are down and back 1/4".
Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm. Lo-pegs are down and back 1/4".
Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm. Lo-pegs are down and back 1/4".
Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm. Lo-pegs are down and back 1/4".
Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm. Lo-pegs are down and back 1/4".
Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm. Lo-pegs are down and back 1/4".
Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm. Lo-pegs are down and back 1/4".
Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm. Lo-pegs are down and back 1/4".
We start with an Excel rim, OEM hub, and Buchanan's heavy gauge stainless steel spokes. Rims and spokes are precision machined for a perfect match to your bike. Upgrade to SUN rims available in 3 colors.
Our pro shop then laces and trues your wheel to perfection, giving you the highest quality custom wheel available.
Add a tire to your wheel order and we will throw in a tube and mount and balance it at no additional charge.
We start with an Excel rim, OEM hub, and Buchanan's heavy gauge stainless steel spokes. Rims and spokes are precision machined for a perfect match to your bike. Upgrade to SUN rims available in 3 colors.
Our pro shop then laces and trues your wheel to perfection, giving you the highest quality custom wheel available.
Add a tire to your wheel order and we will throw in a tube and mount and balance it at no additional charge.
Similar to our Adventure Shirts, this super soft hoodie features our logo on the front and our Topo design on the back. Perfect for those cool evenings or brisk days.
Replace these any time you feel excessive play in the sprocket hub.
Excessively worn dampers can cause the cush hub bearing to fail - which will ruin your sprocket carrier.
Sold as a full set.
Small scuff on sticker, shown in picture. Sold As Is.
Designed to make your compact rack even more versatile for riders who need a larger luggage platform.
Small Scuff on top that does not affect function or fitment, barely visible unless up very close. Available in black only. Comes with original packaging and all hardware. Sold as is.
Rear Fender comes with built in tabs designed to be used with Maier USA Side Panels.
An upright Dakar Rally inspired shield designed to protect the rider without interfering with off-road riding. For on-road riding the Rally shield protects the rider’s core from fatiguing air blasts while keeping the head in clean air. Duck behind it in the cold or the rain to keep from experiencing the brunt of the elements. During off-road riding the Rally windshield protects the rider from any amount of mud, dust, roots, rocks, or branches without becoming invasive. Whether standing on the pegs or ducking behind it, you will be impressed at the protection it offers.
The Rally shield for the TW200 is 13 inches tall, 12.5 inches wide at the bottom, 9 inches wide at the top, and made from military grade 1/8 inch cast acrylic in either clear or tint.
Keep track of your keys easier with our embroidered patch on a keychain.
Finished with metal ring with eyelet and merrowed border.
Patch measures 1.5" x 5"
Our very own high flowing head-pipe is made in the USA using a CNC (computer numerically controlled) mandrel bender for an absolute perfect fit. It is a high quality 3-piece welded two into one, stainless steel head-pipe.
The SS Pro-Flow is a tested upgrade over stock that will bolt right on with no modifications needed.
We recommend a new exhaust gasket when installing your new SS Pro-Flow.
