The Suzuki DR650 is a long-standing model in Suzuki's lineup, introduced in 1990 as a replacement for the DR600 model. The DR is a 644 cc, 4-stroke, single cylinder, SOHC, 4-valve, air/oil cooled dual-sport motorcycle with a counterbalanced engine that develops 36 horsepower. It has a 13 L fuel tank.
Click here for additional details on recommended parts, accessories, and modifications.
| Year | Chain Size: | Front Sprocket: | Rear Sprocket: | Front Tire: | Rear Tire: | Spark Plug: |
|---|---|---|---|---|---|---|
| '90-'95 | 520x114 | 16T | 42T | 90/90-21 | 120/90-17 | DPR9EA-9 |
| '96-Cur | 525x110 | 15T | 42T | 90/90-21 | 120/90-17 | CR10E |
Replace your worn out Mikuni stock drain hoses when they get old and brittle with a replacement hose set.
These 3/16" hoses are measured and pre-cut to length. Kit includes all hoses that fit the Mikuni carburetor.
Is the cylinder head intake boot on your DR650 cracked or weathered, is it missing parts of the lip to seal around the carburetor, have you recently pulled the intake boot off only to realize the O-ring behind it is hard & brittle? This kit is your solution to solving some of those mystery problems and make your bike like new again. There can be a great deal of heat that can radiate behind the cylinder head on a DR650 as it is an air cooled engine. With that comes long term maintenance items that will need to be replaced due to them being made of materials that cannot withstand those constant heat cycles indefinitely.
Our kit includes O.E. parts from Suzuki to include:
This cover acts as an "adjustable leak jet" to fine tune the accelerator pump squirt.
Eliminates "4-stroke bog" when used with correct jetting. Allows the use of correct carburetor settings to optimize performance, starting and reliability. Improved low-end performance with much better throttle response. Investment cast and finished to precise tolerances with internal high volume vertical check valve. Fits all motorcycles and ATVs using a Keihin FCR carburetor Easy installation instructions (including online video) and template.
Not for the stock DR650 carburetor Fits FCR-MX conversions Only.
Direct replacement for the stock spring and exactly like the old Merge Racing spring. Gives a much more consistent accelerator pump squirt. Eliminates the need for the 'O-ring mod', wire or zip-ties on the pump arm. Fits all Keihin FCR-MX carbs except '07-'08 CRF250/450.
Not for the stock DR650 carburetor Fits FCR-MX conversion Only
If you are converting a Keihin FCR-MX 39 to fit on your DR, you need to start here. This 6061 T6 aluminum adapter bonds to the airbox side of the carb so it will easily fit the DR.
Not for the stock carburetor Fits FCR-MX conversions only.
This brass fuel screw offers a longer head to give you a better hold for making adjustments. This is a nice improvement over the standard extended fuel screw. Kit includes one new screw, spring, washer and o-ring.
The Remote Fuel Mixture Screw is 5 inches longer than stock. This gives you plenty of length to easily mount in a convenient location. Will work with the stock BST Carburetor as well as the TM40 pumper Carburetor.
Top quality brass screw with molded knob for easy adjustments.
Not for the stock DR650 carburetor Fits FCR-MX conversions Only.
R&D introduces "Flex-Jet", a simple, effective flexible shaft design. Quick adjustments are now within easy reach. Besides easy access, another benefit is the Flex-Jet's ability to hold its setting. Loose fuel screws are now a thing of the past. Kit includes: Flex-Jet (Remote Fuel Screw), bracket, screw, spring, washer, O-ring and instructions.
Not for the stock DR650 carburetor Fits FCR-MX conversions Only.
OEM Suzuki Float Bowl Drain Screw for the stock BST40 carburetor.
Extended float bowl screws from Wirth Machine for your OEM BST carburetor that use 5/6" or 8mm size wrench to loosen. Allowing easy access to your jets and float without having to remove the carburetor from the bike. Sold in a 2 pack. Stainless steel threads.
Extended float bowl screws from Wirth Machine for your TM40 that use 1/4" size wrench to loosen. Allowing easy access to your jets and float without having to remove the carburetor from the bike. Sold in a 4 pack. Stainless steel threads.
Replacement socket head (Allen) screws for the OEM BST40 Carburetor. The factory screws that hold the top cap and float bowl on the stock carburetor are very easily damaged. The originals are usually installed unbelievably tight from the factory. It is common to ruin the stock screws when installing a jet kit or doing any other carburetor maintenance. Sold in a pack of four. Two for the cap and two for the float bowl.
Replacement socket head (Allen) screws in case you strip out the stock JIS heads on your TM40 bowl. The originals can be stripped out when doing any tuning or carburetor maintenance. Sold in a pack of four, all for the bowl.
The small size and right angle hose barbs make this filter easier to fit into the small space between your fuel petcock and carburetor. Filter body is only 7/8" diameter. Straight filter is 2" long, 90 degree filter is only 1-5/8" long.
This filter is meant for 5/16" fuel lines. Only 1/2" thick it is small enough to fit just about anywhere.
Hate the handlebar mounted choke lever? Can't reach the choke knob? Does your Safari or IMS tank make using the choke difficult?
Our adjustable cable operated choke knob mounts to the left side engine case and works for either the stock BST or Mikuni TM40.
The plastic fitting that secures the stock choke cable to the carburetor is delicate and easily broken. A broken fitting can cause hard to solve idling and running problems.
CNC machined from billet aluminum and anodized black or blue. If you want to retain your handlebar mounted choke this may be the solution.
These no longer fit the new version of the ProCycle Remote Choke Cable. Will not work with the long or short reach choke knobs.
Stock Suzuki choke knob holder guide. Replace your cracked or cross threaded stock unit with a new one.
Replace your handlebar mounted choke with this simple knob mounted directly on the carburetor.
Available in short or long reach.
Long reach is easier to use while wearing riding gloves.
Works for either the stock BST or Mikuni TM40.
Replacement rubber boot for choke knob assembly.
This seal helps keep debris and water out of your DR650 air box and it may become damaged or missing over the years. It is an important part of your DR650's intake system to maintain & prolong air filter life.
Simply, remove the air box door, then remove the old seal and clean out the track it sat in. Set the new seal in place and cut off any excess material remaining. Install the air box door and you are done.
Extra dirt protection for your K&N filter. Our custom made oiled-foam filter sleeve wraps snugly around the K&N filter to give a first layer of protection against dust and dirt. Oil it like you would any other foam filter.
The OEM foam secondary filter can deteriorate rather quickly. Once that happens, it can allow enough dirt into the engine to do significant damage. Replace your filter now with a high-quality foam filter from industry leader Twin Air.
This filter needs to be oiled like any air filter to work properly.
Only for bikes with the stock BST40 carburetor!
The OEM vent foam filter can deteriorate after only a couple of years. When it does it can allow enough dirt into the engine to do significant damage. Replace your filter now with a washable cotton & steel screen filter.
This filter is recommended to be oiled like any other air filter to work properly.
Only for bikes with the stock BST40 carburetor!
Have you lost or broken the stock air filter cage for your DR? Maybe you need a spare? Here it is, the OEM cage that will fit any of the foam air filters on this page. This kit includes the plastic holder that keeps the cage in place and the screw for that as well.
A ProCycle exclusive. This is our favorite air filter for the DR650. Made just for us by the folks at DT1.
NoToil cleaner NOT recommended with this filter. May cause delamination.
FunnelWeb ProLine Filter Highlights:
Like all FunnelWeb filters, the ProLine Filter features profile cut, single layer, single density foam that doubles the external surface area of the filter without increasing the original filter size. The ProLine Filter traps dirt, dust, sand and mud over a larger area on its outer surface, ensuring optimal air flow is maintained for maximized engine performance and reliability.
The single layer, single density polyurethane foam has the added advantage of being easy to clean and the ability to maintain its original shape after numerous washes. Overall, compared with conventional foam filters, FunnelWeb offers more protection from dirt ingestion, has longer service intervals and maintains high airflow rates when dirty.
Dual stage foam: 2 different pore sizes create more trapping area for even the smallest dust particles. Flame laminated foam: Both "Stages" are not glued but heat sealed to provide maximum air flow. Light color foam makes it easier to see where the filter oil has covered and where it has not.
Twin Air's high quality materials and superior construction deliver unbeatable performance and protection. The hands-down choice of more World and National Champions than all other filters combined.
Twin Air's fused layers of open-pore foam and fine inner foam trap even the smallest particles-without restricting airflow.
The screws and nuts that hold the Air-box Cover on have a habit of jumping out of the air-box and running away. No idea where they go, but it is far! These cannot be purchased separately from Suzuki but we found some that are perfect replacements. This little kit includes four screws and the square nuts that go into the air-box. We recommend that you put a dab of silicone or something to hold the nuts in so they don't jump ship like the other ones did.
Sold in 6 packs
Not legal for use on pollution controlled vehicles in the state of California.
Acerbis 5.3 gal tank adds function and great looks to your DR650. This high capacity fuel tank incorporates modern lines and high quality construction that can't be beat. Includes gas cap, petcock and all mounting hardware.
Installation of the Acerbis tank requires relocation of the front turn signals. Otherwise the stock signals will contact the tank at full lock. Our Turn Signal Relocation Brackets Move the front turn signals up and forward to clear the bigger tank.
We've been asking for a bigger tank for years and it's finally happened. This is the big brother to the very popular 5.3 gallon Acerbis tank with some modifications to add another gallon and a half of capacity. It's the same width between the knees but extends wider and further forward in front of the knee pockets. This high capacity fuel tank incorporates modern lines and high quality construction that can't be beat. Includes gas cap, petcock and all mounting hardware.
Installation of the Acerbis tank requires relocation of the front turn signals, otherwise the stock signals will contact the tank at full lock. Our Turn Signal Relocation Brackets move the front turn signals up and forward to clear the bigger tank.
You want a lighter replacement for your heavy steel stock tank? Don't need the extended range (or bulk) of a big tank? The 3.7 gallon tank from Clarke might be just right. It's almost 5 lbs lighter and holds close to 1/2 gallon more fuel than stock to increase your range by about 20 miles. Fits with your stock petcock, Pingel or Raptor petcock.
Get better range from your DR650 by adding an IMS 4.9 gallon fuel tank. Available in Natural, White, Black and Blue. Natural color is recommended if you wish to easily see the fuel level in the tank. Includes cap and fuel petcock.
We worked with TechSpec to have them make custom tank grip pads that look great on both Acerbis (5.3 and 6.6 gal.) and IMS tanks. These pads not only cover those ugly scuffs, but give great knee grip to the slippery plastic.
These have been tested on two of our shop bikes for over 3 years, they did not bubble or peel off in any way.
TechSpec’s Motorcycle Tank Grips were developed to improve body, bike control and increase riders comfort. Gripping your motorcycle between your knees or thighs improves overall control of your ride by better securing your body weight and seat position under the forces of braking, cornering and acceleration while also relieving pressure from your wrists, elbows, shoulders and lower back giving you increased control and a more comfortable, safer ride. Snake Skin is a thin, .125” medium durometer “rubber” material that offers a secure, comfortable grip, durable protection and a clean stock look.
This universal precut kit includes left and right tank grips. (8" X 3") Triangle
Security for your fuel tank. Includes 2 keys. Internally vented with a check valve that prevents spillage in case of a tip over.
Fits Acerbis, IMS and Safari tanks only.
A replacement Clarke Gas Cap that fits most Clarke Gas tanks. Comes with rubber gasket.
A replacement gas cap for your IMS tank. Newly redesigned to resist damage from new fuel additives that were hard on the seal in the old style cap.
If you need a replacement cap for your Acerbis tank, why not go bling? These caps have a carbon fiber pattern molded into them that is extremely realistic. Looks like the real thing. Topping off the cap is a CNC Machined metal vent cap. This eliminates the need for a lengthy vent tube that gets in the way. The vent cap allows air to vent into the tank but does not allow fuel to splash out during normal use or during a tip over.
These caps fit Acerbis tanks only.
If you're like us, you hate the long floppy vent hose hanging off the cap of your aftermarket tank.
This one-way vent cap replaces the long hose with a short one only about 2" long. It allows air into your tank but prevents fuel from sloshing out.
Machined from billet alloy and anodized for good looks.
Not for stock fuel tanks!
Does your stock vacuum operated petcock not shut off when your bike is parked? Replace your stock vacuum operated petcock with this manual one. Must be shut off any time the bike is parked for more than a few hours. Fits stock or aftermarket tanks.
Aftermarket plastic tanks might need the hole cut into an oval shape to fit the two standpipes.
Replacement Acerbis left-hand side fuel tank petcock.
For Acerbis tanks only.
Really like your stock vacuum petcock and never having to worry about turning it off? Did the seals go bad and it leaks? Plugged up? Well, whatever your troubles, here is your replacement. Vacuum operated so you never have to turn it off! Just like the stock unit. Includes mounting bolts with washers, fuel line, clamps and a protecting coil wrap.
Aftermarket plastic tanks might need the hole cut into an oval shape to fit the two standpipes.
For those people who have been wishing for a dual petcock setup for their Acerbis 5.3 and 6.6 gallon fuel tanks. Install this kit to get the last bit of fuel from the right hand side of the tank without tipping the bike on its side. Includes the right hand fuel valve, o-ring, screws, tee fitting, fuel hose and spring action hose clamps. You will have to drill the hole in your tank for the petcock standpipe. For Acerbis tanks only.
Does your stock vacuum petcock leak? Won't shut off? We have the solution with this rebuild kit. Includes a new vacuum diaphragm, O-ring, gasket and inner seal.
A popular upgrade from the stock vacuum operated fuel valve. Manually operated. Must be shut off any time the bike is parked for more than a few hours. Fits stock tank or aftermarket tank and has both main and reserve. Fully rebuildable.
You’d be amazed at the dirt and debris that can work its way into your gas can – and from there, your fuel tank. Twin Air’s monofilament screen pocket inserts in your tank to catch particles as small as 40 microns (.00165”) while allowing the gas to flow freely.
The flange is custom-sized for each modern 4-stroke model to ensure a leak-proof seal. Just remove the filter periodically, turn it inside-out, and clean out the debris that could have been in your engine.
Will not work with factory locking gas caps.
Inside tank inlet diameter must be approximately 43.5mm (1.71") to fit.
All of these lines are stronger and more durable than vinyl fuel lines and are resistant to swelling, UV light, as well as hardening and cracking.
Five-layer Greenshield® Barrier Technology cuts vapor loss and saves fuel, making it safe for the environment and fuel efficient.
1. Barrier tube - provides high heat and corrosive liquid resistance.
2. Greenshield® barrier - patent-pending technology provides the lowest permeation in the industry.
3. Adhesion layer - secondary protective barrier.
4. Reinforcement layer - spiral textile reinforcement provide strength and pressure resistance.
5. Cover - protect underlying components.
All of these lines are stronger and more durable than vinyl fuel lines and are resistant to swelling, UV light, as well as hardening and cracking.
Five-layer Greenshield® Barrier Technology cuts vapor loss and saves fuel, making it safe for the environment and fuel efficient.
1. Barrier tube - provides high heat and corrosive liquid resistance.
2. Greenshield® barrier - patent-pending technology provides the lowest permeation in the industry.
3. Adhesion layer - secondary protective barrier.
4. Reinforcement layer - spiral textile reinforcement provide strength and pressure resistance.
5. Cover - protect underlying components.
Ordering new fuel line? How about a set of fresh zinc plated clamps to go with it?
These will be sure your fuel line stays connected. A pack of 8 clamps in 2 sizes to fit most 1/4 or 5/16 fuel hose.
Hose reducer to go from 5/16" line down to 1/4" line. Many bikes have 5/16" carburetor spigots but most aftermarket petcocks are 1/4". This solve the problem of mismatched sizes. Solid brass construction. Can be used to route or repair fuel lines, oil lines or air lines. Barbed ends provide a secure fit.
Have your tank cushions worn out over the years? Have you lost one or more while working on your bike? We have new upper and lower tank cushion rubbers.
This kit includes the original hardware, upper, and lower cushions.
Need to mount two containers? A water and a fuel? Two waters? Already have a RotoPax Mount for a single container? Get this extender to work in conjunction with a pack mount and that will be no problem! Single mount, two containers.
RotoPax holder made to mount a single Fuel and/or Water container.
Need to mount two containers? A water and a fuel? Two waters? Get the extender which allows you to stack two containers no problem! Single mount, two containers
RotoPax holder made to mount a single Fuel and/or Water container.
This unique design adds strength and provides extra tightening power.
Use with included base plate or remove plate to attach mount direct by bolting up through the bottom or down through the top.
RotoPax are Rotational Molded - the process which produces indisputably superior products.
Need to mount two containers? A water and a fuel? Two waters? Finally, you can stack multiple packs together! Use in conjunction with a pack mount. You will need to purchase the Single Mount as well as the Extender.
Auxiliary fuel tanks mount to handlebars, forks, or rear racks.
Mounts to existing signal brackets to move the front turn signals up and forward to clear the bigger 5.3 & 6.6 gallon Acerbis tanks.
Quick release one-piece clamps that saves space. These are great for fuel lines, controlling wires, and can be used many times.
Comes with 4 each of 8mm, 9mm 10mm, and 12mm.
No special tools needed, from Helix Racing.
This Super Siphon has a (1/2 inch x 6 foot) long hose, which makes it quite easy to transfer fuel from one bike to another! Simply, shake the hose to prime it and get fuel moving. The hose is resistant to gasoline and any other hazardous chemicals. Roll it up, stuff it in your bag and you will be very happy whenever you need it.
Aero Tapered Aluminum (ATA) Oversize (or Fat Bar) Handlebar.
For bikes with factory 7/8" handlebars these will require the use of a 7/8 to 1-1/8 adapter (sold separate).
Comfortable Oversize (or Fat Bar) Handlebars.
For bikes with factory 7/8" handlebars these will require the use of a 7/8 to 1-1/8 adapter (sold separate).
Say goodbye to the frustration of fidgety handguard expansion plugs with Warp 9's innovative Tapped Handlebars.
These handlebars feature ends that are plugged and tapped with an M8x1.25 threaded insert, providing a secure and reliable mounting point for all aftermarket wrap-around handguards.
No more worrying about plugs pulling out or spinning during crashes; their robust design ensures you're good to go, even when you encounter obstacles.
Not using handguards? No problem they've got you covered!Each set of handlebars comes with aluminum grip guards and stainless bolts, offering protection for your grips and delicate throttle tube in case of a get-off.
Designed with an oversized 1-1/8 inch (28.6mm) clamping diameter that tapers down to 7/8 inch (22.2mm) to accommodate standard controls. Crafted from 7010 T6 aluminum tubing and featuring computer-extruded variable wall thickness, they effectively reduce vibration while enhancing overall performance and comfort.
Note: Does not include pictured bar mounts.
| Width | Height | Rise |
| 790mm | 101mm | 71mm |
| Clamp Area | Sweep | Bend |
| 142mm | 73mm | CR High |
Here is a complete kit to install oversized tapered 1-1/8" handlebars on your DR650. Warp9 handlebar clamps bolt to your stock triple clamp adding an additional 1" to the height.
Alloy oversize bars offer more durability and eliminate the crossbar which opens up your dash area for more goodies. Black in color.
This kit is for those of you looking for a bit more leg and arm room in the DR cockpit. Included are ProCycle Low Foot Pegs and our oversize bars.
Mika Metals Hybrid Series handlebars are truly a marvel of engineering. It is the first oversize handlebar in the world that fits on 7/8" clamps.
The patent pending design is the most unique idea to shake up the handlebar industry in quite some time. They retain all the flex properties of the pro series handlebars and allow you to run oversize bars without the oversize clamps.
Constructed from the highest quality aerospace 7075 aluminum for maximum strength. CR High Bend, includes injection molded bar pad.
Bars only fit 7/8" clamps
ProTaper's ADV handlebars give you a bar taller than most with extra space on the control portion of the bar. These bars provide an additional 20mm of space next to where your levers and throttle are located for your GPS, phone cradle, auxiliary switches, etc . They come in Adventure (which is taller than stock) and Adventure High (which is even taller).
These are oversize bars, which means they are are 1 1/8", not the smaller 7/8" diameter. Therefore some bikes will require a adapter and there are several available to select from.
Using the same manufacturing techniques and materials as ProTaper’s industry-changing 1⅛" motocross handlebar, the EVO Adventure is specifically designed to provide adventure/touring riders with the increased comfort and control they need. With over 8" of straight section in the control areas, mounting vital components is made easier than ever. With its premium 7000 series aluminum alloy construction and computer-profiled four millimeter-thick wall design, the EVO Adventure Handlebar is up to 25% lighter and 45% stronger than competing handlebars.
These 7/8" bars fit in the stock clamps and raise your grips a couple inches. They look great too!
| Width | Height | Rise |
| 813mm | 160mm | 104mm |
| Clamp Area | Sweep | Control Area |
| 236mm | 100mm | 199mm |
Mount these polished billet aluminum spacers under your handlebar clamps to raise your handlebars 1 inch. High quality longer bolts are included.
Requires 7/8" factory bar clamps on bike
These versatile Risers allow you to clamp a 7/8" diameter handlebar or you can remove the 7/8" reducers and then clamp an 1- 1/8" aluminum "fatbar". If you are thinking of going to a fatbar after you bend your stock set or just want the versatility and option to run any bar, this is the riser to go with. Reducers lock into risers to insure no slippage between components.
These risers use 8mm bolts. Always check and confirm that your bike has adequate cable and brake line length before installing any handlebar risers.
Anti-Vibration Risers may interfere with aftermarket large capacity fuel tanks, and some steering stem clamp configurations (in these cases we recommend using standard pivoting risers).
This unique design from Rox allows you to move your bars either closer (1" up and back) or further away (1" forward and 1-1/4" up) depending on rider preference. These risers have an oblong mounting hole so that they will fit virtually any triple clamp with 8mm bolts. A set of reducers lock into the risers ensuring no slippage whether you have a 7/8" or 1-1/8" bars.
Because these are offset there may be limited clearance between the gas tank and the risers when the bars are fully turned on some models, mainly when mounted to move the bars closer.
Handlebar mounts that replace your stock clamps.
These raise your handlebars 1 inch.
Choose 7/8" for standard handlebars or 1-1/8" to allow installation of your choice of oversize/ tapered handlebars.
The GPR v5 is the fifth generation steering damper designed for dirt bikes, adventure bikes but is also used on several of hybrid applications. Its compact and slim design allows for the damper to be mounted below the handlebars, out of harm's way, without raising the bars more than an inch. Frame mounts are machined steel or Cryogenic treated billet aluminum with stainless steel pin, and billet aluminum machined bar-mounts.
Will only work with Fat Bar style (1 1/8" clamp area) handlebars and stock triple clamp.
Introducing the Zeta solid bushings to replace your worn out rubber bushings. We have tested these bushings on our own bike and we love them. No more sloppy handle bars. Plus, they add a little bling factor to your bike! Simply unbolt your bar mounts and swap the rubber bushings with these anodized billet bushings for a more stable handlebar feel.
Features:
Protect your thumbs from blisters caused by riding on the inside of your grips.
Sold in Pairs.
The elegant, open-end design makes these heated grips both stylish and functional. Highly efficient design, delivering warmth faster than traditional heated grips. Five-level temperature controller adjusts the grips accurately to avoid overheating. Specially selected rubber material resists the outdoor environment and provides a secure and comfortable grip. Even at high-temperatures, the grip remains resistant to damage.
Choose from the standard five level push button temperature controller, or the LCD display controller which shows the selected heat level and available battery voltage.
The Apollo Heated Grips are designed with an integrated adjustable thumb switch, which allows them to easily fit on any kind of motorcycles on the market. The integrated thumb switch gives control to the rider to adjust the temperature level while keeping hands on the bar for a safer ride.
Its wide temperature setting range will keep the rider comfortable under the cold riding conditions.
The 5 color LED display will enhance the visual look of the heated grips and will allow the rider to quickly know at which heat level the grips are set.
This system will also detect if the battery voltage is too low and will automatically shut down the heated grips in order to make sure the rider have enough power to start the engine or use the motorcycle.
Specifications:
These heated grips from Koso have been tested by us and we can say they will keep your hands warm and give you the grip you need in off road conditions, thanks to the full diamond grip design.
These new heated devices are for the user that does not want to commit to changing their grips but still wants to maintain the comfort of heated grips. The fitment is intended to fit all sorts of handlebar sizes. They can be installed and removed in a matter of seconds and kept in any sport bag when not in use.
Features:
Designed to mount to the front of any mx/offroad grip for added control in WET/MUDDY conditions. A necessity for those pouring down, rainy days on the trail to enable mechanical traction between your already installed grip set and the inside of your 1st row of knuckles. Each Mud Knuckle is injection molded in-house at ODI and includes 8 Safety-Wire Slots to perfectly secure to the front side of your grips. Improves traction in extremely wet and/or muddy conditions.
KIT INCLUDES:
Grips not included.
These grips feature a thicker design that dampens vibration. The soft shoulder allows ease of movement. Three wire-tie grooves are molded into the grip to make securing them a breeze. We think they are great!
ProTaper Pillow Top Grip with 3-D (Tri-Density) Technology. Try the grip with the technical advantage of three dedicated rubber compounds.
ProTaper Pillow Top Grip with 3-D (Tri-Density) Technology. Try the grip with the technical advantage of three dedicated rubber compounds.
The difference between the original Pillow Top and the Pillow Top Lite is the overall diameter of the grip surface. The Lite offers a smaller diameter so the grips don't feel as large reducing fatigue in your hands while riding.
Each pattern is available in three advanced synthetic rubber compounds. This means you can have the optimum combination of strength, tackiness and shock absorption to suit every riding condition and individual style. Soft grip is extremely soft, giving you a very comfortable ride, great feel and reduces the chance of blisters; however, because the grip is so soft, it wears quickly. Medium is a compromise between firm and soft. Firm grip has the same feel as a stock grip, it is very strong and has very good resistance to tearing and abrasion. Half Waffle has waffle pattern in finger area for traction and diamond pattern on palm side to reduce blisters. Full Waffle: designed after the CR Honda® grip.
This little jewel reduces hand fatigue and cramping on long rides or daily commutes. The Crampbuster is not a throttle locking unit but, rather a simple clip-on device which allows you to relax your grip while riding.
The Go Cruise cruise control mounts over the throttle grip and rests on the brake lever to hold your throttle open, allowing you to stretch and rest your hand on long rides. Installs and removes in seconds with no tools. You can roll off the throttle manually to disengage the Go Cruise.
NOTE: These will not work with Warp 9 levers
The Go Cruise 2 cruise control mounts over the throttle grip and rests on the brake lever to hold your throttle open, allowing you to stretch and rest your hand on long rides.
Ease the pressure on your wrist during those long highway drones out to where the fun begins. ProCycle has developed this kit that includes a Vista-Cruise throttle lock, a specially modified alloy throttle tube and an anchor plate that attaches to your throttle housing. Just flip the thumb lever down to apply enough friction to hold the throttle in place. Use the supplied longer screw to attach the anchor plate to your lower throttle housing bolt hole. Also included is a tension adjustment tool that you can keep on your key ring. Keep the applied tension lightly adjusted so it's easy to roll the throttle off.
Fits bikes with dual cable throttle housings.
Suzuki makes it almost impossible to replace your stock grips. It's much easier with a new throttle tube.
This anodized billet piece, brings a touch of color to your bike. Available in red or blue, it replaces the stamped steel clevis that connects your brake pedal to the master cylinder.
Warp 9 has created a beautiful brake pedal machined from billet aluminum to an 8mm thick work of art. A stainless steel pin eliminates wear in the frame. This pedal has the ability to move the spring loaded brake tip 10mm either way from the center position. The arm is arched to provide clearance for riders who have the lowpeg + centerstand combination.
