The Suzuki DR650 is a long-standing model in Suzuki's lineup, introduced in 1990 as a replacement for the DR600 model. The DR is a 644 cc, 4-stroke, single cylinder, SOHC, 4-valve, air/oil cooled dual-sport motorcycle with a counterbalanced engine that develops 36 horsepower. It has a 13 L fuel tank.
| Chain Size: | Front Sprocket: | Rear Sprocket: | Front Tire: | Rear Tire: | Spark Plug: |
|---|---|---|---|---|---|
|
520x114 ('90-'95) 525x110 ('96-Cur) |
16T ('90-'95) 15T ('96-Cur) |
42T ('90-'95) 42T ('96-Cur) |
90/90-21 | 120/90-17 |
DPR9EA-9 ('90-'95) CR10E ('96-Cur) |
Ultra bright amber LED turnsignals offer nearly the same visibility as OEM in a much smaller package. 15 amber LEDs in every signal. Flexible rubber stalks. Requires a LED turn signal to flash properly.
Pack of Two
These Sequential Turn Signals are available in a 2 pack or 4 pack short stem with 7 LEDs.
Matte Black, plastic body with smoke lens and 8mm mount bolt.
Specifications
Triangle/Teardrop style signals with LEDs. Mounts on any flat surface to keep out of the way of brush, branches, and your exhaust system. Requires LED flasher or LED turn signal resistors to flash properly.
This Diode Kit is only necessary if you have a single dash indicator for your turn signals. One dash light for both left and right signals (such as on the DR650).
This kit allows power to flow in just one direction from the LED signals to the dash indicator light regardless of which direction you are signalling.
When upgrading your Suzuki DR650 with LED turn signals, it's required to install a diode module to prevent all of the signals from blinking at once regardless of left or right signal activation. Some riders choose to splice and solder their own solution, but we like things plug and play. That means all you have to do is plug in the TST kit and you're done! There's no need to cut or splice your OEM wiring harness or break out the soldering iron and electrical tape.
You may have noticed after adding aftermarket turn signals (especially LED units) that your blink rate has significantly increased. OEM flashers are designed for standard bulbs which draw a few watts each, much more than typical aftermarket bulbs or LED signals. This device is an effective alternative to using load resistors because it consumes considerably less watts, consumes less space, and does not generate excessive heat.
The plug is exactly the same as the OEM unit making swap outs a cinch. No wiring changes, cutting and adding connectors. Just plug it in and you will have a steady flash at the DOT OEM rate regardless of what signal bulbs you use. It is an all solid state design and will blink correctly with loads all the way down to 0.1W / 0.01A.
Not for any DRZ400 or Royal Enfield Himalayan
This type of flasher is required for LED turn signals. For DC (battery) systems only. Includes 2 female connectors for universal fit.
Not compatible with any DRZ400
Works on AC and DC lighting systems
Not compatible with any DRZ400
If you just installed aftermarket LED turn signals or an LED integrated tail light and your turn signals are flashing way too fast, or perhaps simply staying on completely, you're at the right place to find the solution! The TST Gen2-SK LED Flasher Relay fixes what we call "hyperflash". It slows the flash rate down to a pre-set 85 cycles per minute but can be sped up or slowed down using the adjustment dial located within the unit so you can get the exact speed you are looking for. The plug-and-play installation means that you don't need to splice in any load balancing resistors that generate unnecessary heat and require splicing into your stock wires. Simply remove the stock relay and install your new TST relay and your wiring job is done. It's that simple!
Please make sure your bike uses a 2-pin relay for the signaling system. If your bike has hazard lights it may need the 4-pin relay. Please also note the pin configuration and make sure it matches what is on your bike. It is very important to verify fitment before making your purchase.
The SignalMinder unit is designed as a plug-in accessory for many Japanese bikes. SignalMinder uses a microprocessor to cancel the turn signals at one of three selectable time outs; 10, 20 or 30 seconds.
You can also make it so that all four of your signal lights also act as running lights and establish a dual-channel system on your bike. With the dual-channel system, when you activate the RIGHT turn signal three times in succession, you get 4-way hazard flash lights.
Connecting the 12 volt supply from the brakes to the SignalMinder, also allows for a brake flash option.
There are many options and configurations using this electronic tool.
No wire cutting required. The kit includes Scotchlok connectors to tap into existing wires.
Allows LED type turn signals (and low wattage flush mounts) to flash using a standard flasher unit. Connectors included. One kit works with 4 signals.
The Barkbusters 10 OHM Resistor Set for LED Indicator Lights will correct the flash rate of your auxiliary signal lights. Ready to plug in connectors make installation a breeze. These resistors are intended for Barkbusters LED Indicator Lights.
Features:
This devices allows any two wire after market LED turn signal indicators to operate as running lights (always on), and will blink on / off when the turn signal switch is activated. It is highly recommended to use this product with the Fixed Rate Turn Signal Flasher. This device, as well as aftermarket turn signals, use much less current than stock turn signals, thus an increased flash rate will occur. Load resistors or a fixed rate turn signal flasher will get your flashers operating at the normal flash rate again.
Each package contains two separate adapter boxes, good for operating both turn signals, left and right of either the front OR rear of your motorcycle. You will need to purchase a 2nd kit if doing the Front AND Rear of the motorcycle.
This device is universal; designed to work for any motorcycle with a DC electrical system. Kit comes with bullet connectors to wire in manually. Works with any two wire non-sequential aftermarket LED turn signal indicators.
Fits Most Models
These turn signal relocation brackets from ProMoto Billet provide an easy way to move the stock turn signal lights, useful if you find them getting in the way of your luggage configuration.
These brackets may utilize an existing hole in some of the rack side brackets, though many applications will require drilling or fabricating in order to mount properly.
Replacement Halogen bulbs for mini style turn signals. Sold in a pack of 5 bulbs.
Mounts to existing signal brackets to move the front turn signals up and forward to clear the bigger 5.3 & 6.6 gallon Acerbis tanks.
Roll-up pouch ideal for tucking away your lights when out on the trail.
Taillight and brake light Attaches to the top of the rear fender. Dimensions: 3 1/2" wide x 2" long x 3/4" tall. D.O.T. approved.
LED powered taillight, brake light, license plate light & license plate mount. Attaches to the underside of MX style rear fenders.
Taillight, brake light, & license plate holder (no plate light). Attaches to the underside of MX style rear fenders. Small and good looking!
Taillight, brake light, & license plate light. Attaches to the top side of enduro style (XR, KDX, etc) rear fenders. Dimensions: 2 3/4" x 4 3/4" x 2 1/2" tall. Wiring instructions included.
Taillight, brakelight, turnsignals, license plate light & license plate mount. Taillight is DOT approved, turn signals are not. Attaches to the underside of MX Style rear fenders. Turnsignals are embedded in the taillight housing. Wiring instructions included.
*Flushmount signals may require resistors to flash correctly
Installing new turn signals or brake lights and need to find the 'HOT' wire, or are you just trying to find out if a specific wire has power going to it? Either way, this test light can help you locate shorts, open, and voltage on 12-24 volt DC circuits.
Has both high and low beams. Attaches to the upper fork tubes with rubber straps. DOT and CE approved.
Greatly eases basic chain maintenance, tire changes, parking, cleaning, etc. All necessary hardware is included. Installs using basic hand tools. Tough black powder coated finish.
For riders who wish to run the centerstand and the lowered footpegs we recommend installing a Warp 9 brake pedal. The Warp 9 pedal is arched to give the necessary clearance under the pedal.
T-Rex stands are made from steel tubing finished in black powder for durability. Back by a 3-Year limited warranty for any material or manufacturing defects. Rest assured that you are getting best material commercially available.
Greatly eases basic chain maintenance, tire changes, parking, cleaning, etc. All necessary hardware is included. Installs using basic hand tools.
This kit is for those of you looking for a bit more leg and arm room in the DR cockpit. Included are ProCycle Low Foot Pegs and our oversize bars.
For the DR650 that has been lowered or converted with supermoto wheels. This stand is 1.5" (40mm) shorter than the stock unit.
Includes a rear shock mount cover plate and plug for lowing the stock shock.
If you are replacing your side stand you will want to check the hardware. Over the years they can take a beating and the springs become lost or broken.
This is the full kit that includes #4, #5, #2, and #3 in the diagram.
Your choice of an aluminum bolt-on foot pad or a steel weld-on unit. Each will make the footprint of the stock side stand considerably larger, preventing your DR from tipping over in soft terrain. The bolt-on unit is cut from aluminum and then powder coated black, it comes with stainless steel mounting hardware.
The bolt-on pad and does require use of a drill for installation. The weld-on pad will need to be welded to the stand and then the entire unit painted for corrosion protection.
Low peg mounts from JNS Engineering. Your choice of a straight 1.5" drop or get that drop and a 1" rearward offset. You can use your stock pegs or click on one of the optional pegs that are made to fit the stock DR650 mounts.
These heavy duty steel mounts are pressed, welded and then powdercoated black for protection. Includes mounting bolts.
Note: These mounts are compatible with the SW Motech Center Stand by adding a 1/8" spacer behind the mounts.
Low peg mounts for the DR From Wirtz Wire. These are different than our other mounts for several reasons. First, these are designed around the stock pegs. All of the pegs in this section will fit these mounts. Another difference is that these mounts are offered in a low mount as well as a low and rearward mount. These are 'wire EDM' machined from solid 1018 steel bar stock, and are not welded anywhere. They are powder coated black for a great look. Both mounts move the pegs down 2" while the low and rear mounts also move the pegs back 1.3".
Kit comes with new mounts, longer bolts and a longer brake switch spring that will be needed. Pegs are optional, your stock pegs will work.
The upper image shows the low and rearward mounts while the one below that is of the just low mounts. If you look at the two images below that, you will see that these are the low and rearward pegs for both sides of the bike.
Made from 1/8" thick stainless steel with dual folded edges for additional strength, these brackets will relocate your passenger pegs down 4" and move them back 1.5". This will give your passenger additional legroom making two-up riding much more comfortable.
All hardware is included for a quick and easy installation.
Replacement Cleats for use with Fastway Pegs.
Inexpensive way of getting the factory look. Adds 1/2" of width to any standard foot peg. These will give you a much more stable platform when standing on the pegs.
Sold in pairs.
Not your average rubber insert! These rubber covers go over the top of your MK3 or MK4 Pivot Pegz so that the aggressive teeth are only exposed when you need them in muddy conditions.
Important to verify which style Pivot Pegz you have before ordering.
Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm. Lo-pegs are down and back 1/4".
The IMS Super Stock pegs are the perfect choice for both the daily commuter and the rider-in-training. Their mellow tooth design keeps you planted while preventing wear on your soles. They are also perfect for young riders who don't need or want a more aggressive option.
Wider foot pegs for sure-footed comfort.
17-4 cast stainless steel.
| Width | 1.97" |
| Length | 3.18" |
Our complete foot peg assemblies. 1-3/4" lower than stock. No extra brackets that hang down below the frame. Easier on the knees. Wider platform Yamaha YZ style footpegs are stronger and give you firmer footing. Mount solid to the frame. No more 'droopy' feeling when standing on the stock pegs. Lowering your footpegs makes it easier to stand and less of a reach down to the bars when standing.
Now you can get our Low Pegs with MK4 Pivot Pegz or black Fastway ADV pegs (both Yamaha YZ pegs) installed!
Light weight and strong. These DRC foot pegs have a wider platform for increased comfort and control. Cast from Chromoly steel for unbeatable strength and durability.
Services two Pivot Pegz and fits MK2, MK3 and MK4 Pivot Pegz
Kit Contents:
Fastway offers a large ADV peg that is 4.75" long and 2.25" wide. With these pegs you can adjust the camber with their patented FKMS Kamber bolt. ´Tilt´ your pegs to increase comfort, or to give better squeeze on your bike. These pegs come with two sets of F3 cleats (one standard, one long). You can order serrated or spiked cleats separately.
These Adventure pegs are offered in several colors, but some colors may require extra time, call for availability.
Designed and sculpted out of the best 7075 Billet aluminum by Pro Moto Billet elite engineers and machinists. Featuring Fastway's Patented adjustable height, traction, and camber options, the Evolution AIR footpegs are superior in every way. Fastway Evolution AIR pegs are designed to shed mud and debris, while being ultra strong.
You can also order serrated or spiked cleats separately.
These AIR pegs are offered in several colors, but some colors may require extra time, call for availability.
Pivot Pegz have set a new standard in footpeg performance and quality, and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty.
Pivot Pegz aim to build the best footpegs in the world and they really do perform as good as they look. Here's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever.
See below for extenders for these pegs to make them true ADV pegs!
These top of the line Adventure pegs from Warp 9 are 5" long and 2.5" wide. They will give your feet the perfect perch whether you are cruising down the highway or standing up hammering down a singletrack trail.
Have your tank cushions worn out over the years? Have you lost one or more while working on your bike? We have new upper and lower tank cushion rubbers.
This kit includes the original hardware, upper, and lower cushions.
Tapered roller bearings provide decreased maintenance, less wear, smoother operation and longer life.
This set of high quality replacement steering stem bearings includes:
Replacement OEM swingarm pivot covers. Keep mud and dirt away from the swingarm bolt. Sold as a set of one left side and one right side cover.
Many riders choose to convert over from the stock 525 to a 520 chain. Besides being lighter and less expensive, a 520 chain is more readily available as well as having more sprocket size options.
Quality steel sprockets and EK SROZ2 525 O-Ring chain. Available in gear ratio choices from - 13/42 to 15/46. EK SROZ2 525 chains come in 120 link length and may have to be cut down to fit. They also come with rivet type master links. Clip type links are available below.
13 and 14 Tooth sprockets require a smaller retainer
This is a complete drivetrain package. All the parts you need to freshen up the most important part of your motorcycle.
High Quality chain. Will need to be cut to fit your sprocket combination.
High Quality chain. Will need to be cut to fit your sprocket combination.
Lower friction and longer life. X-rings have twice the sealing ability as compared to o-rings. They do a better job of keeping the lube in the links and the dirt out. DID VX chains have a reputation for being the best chain you can buy for dual sport riding. DID VX chains come with rivet type master links.
Always carry a spare master link when out on the trail.
Master links are not interchangeable. Be sure to check the manufacturer and series on your chain.
These do not fit the TW200 or XT250. Only for 520 os 525 chains, Please verify chain size.
This is a RIVET style master link that fits the original OEM Suzuki chain. The original chain is marked DID 525 V8. If you need a master link for your stock chain, this is the one.
There is not a clip-style master link available.
Polyurethane drive cushions for the DR. Polyurethane has a higher abrasion, cut, and tear resistance than rubber as well as much better resistance to chemical breakdown. This will offer longer life and better damping when compared to the stock rubber cushions.
The DR650 is rather hard on the cush drive rubbers. Replace these any time you feel excessive play in the sprocket carrier hub. Excessively worn dampers can cause the cush hub bearing to fail - which will ruin your sprocket carrier. Sold as a set of 6 rubber dampers.
Quality steel front sprockets. Choose 525 or 520. Also available 'Wide Boss' JTF438 520 sprockets.
All 520 sprockets require a new retainer plate, please add on if purchasing this size.
A set of three OEM Suzuki front sprocket bolts. Thread-lock compound has already been applied for extra security.
The stock sprocket retainer will rub the chain when it is used with 13 and 14 tooth sprockets.
We have our own sprocket retainer laser cut from 13 gauge stainless steel. This retainer works with all 3-hole 13T, 14T, 15T and 16T DR650 countershaft sprockets.
Quality steel rear sprockets. Choose 525 or 520. 41T to 50T
48 and 50 sprockets require removal or modification of your lower chain guide.
Chain Size Recommendations:
*Actual sprocket color may differ from image shown.
A set of six high quality grade 10 sprocket bolts with lock nuts. Thread-lock compound has already been applied for extra security.
These bolts are flat head style, requiring a countersunk hole in the sprocket.
This is a genuine Suzuki part. We recommend installing a countershaft seal retainer to prevent the countershaft seal from popping out while riding.
OEM Suzuki seal retainer for the DR650. Simple insurance against your countershaft seal popping out of its bore.
This is not a common problem but for those folks who have had the seal come out it has proven to be quite difficult to get it to stay in place. This steel retainer eliminates any possibility of the seal coming out and ruining your day by coating your rear tire with oil.
The cush hub (sprocket carrier) bearing leads a tough life. This is especially true if your cush rubbers get old and soft. They can allow the chain to pull the cush hub sideways putting a twisting load on the bearing. If there's any question about the condition of your bearing replace it now with this double sealed bearing and quality seal.
This nice piece replaces your plastic sprocket cover and protects your engine case from a chain derailment or failure. The 3/16" (5mm) thick steel plate is adjustable to accommodate 14, 15 and 16 tooth sprockets. Includes mounting hardware.
This new unit from JNS will protect your cases from the damage caused by a thrown chain, and will also keep your pants, boots or foot safe from your countershaft sprocket.
The case saver portion is laser cut from 0.25" aluminum and then has the 0.19" aluminum countershaft sprocket cover welded to it and the entire unit is powder coated black.
All the mounting hardware is stainless steel with machined aluminum spacers also included.
If you have a 16t front sprocket, mounting modification may be needed to fit. Install the case saver on the bike without the top spacer and bolt. This provides a little extra wiggle room. Add the top spacer and bolt after the bottom bolts are loosely threaded.
B&B fired up the CNC equipment for another beauty, a Front Sprocket Case Saver. A great investment the 6mm aluminum base will protect your engine cases should your chain ever break or derail. On top of that is a 4mm piece to keep your pants and other things out of the chain as well. This replaces the stock cover over the countershaft sprocket.
If you have a 16t front sprocket, mounting modification may be needed to fit.
Stock chain guard crack and crumble on you? Won't happen to this unit CNC machined from 2.5mm marine grade aluminum. Polished to a beautiful sheen that will give your DR that little twinkle as well as better protection.
Replace your lost or broken stock plastic chain guard with a JNS aluminum one. Laser cut, CNC formed, TIG welded, and powder coated a beautiful satin black. This is a direct replacement for the stock unit.
Please note that this unit is a bit wider than the stock one and will have to be trimmed if you are running a big fat SuperMoto wheel/tire.
A real Heavy-Duty Chain Guide manufactured from 5mm (3/16") thick 5052 Aluminum. This guide will take a pounding and continue to put that chain right on the sprocket. The rub block is machined from UHMW plastic and can be positioned to fit just about any sprocket available for the DR. These are powder coated black for a great look and additional protection.
A CNC machined chain guide for the DR. Stronger than the wimpy stock unit and can easily accommodate the stock 525 chain as well as a 46 tooth rear sprocket (by moving the lower rub block to the forward position). The rub blocks are also a higher grade, longer lasting material.
Replace your lower chain roller with this high quality roller with 2 sealed ball bearings. The stock roller has no bearings. It's just a plastic wheel riding on a bolt. Ball bearing chain rollers are smoother, quieter and last longer.
Savvy DR650 owners will remove the upper chain roller. You can use this stainless steel button head screw to plug the threaded hole. Suzuki did not make the upper roller mount strong enough. If you don't remove it yourself the chain will likely do it for you - along with a chunk of metal out of the frame.
The chain slider protects the swingarm from contact with the chain. Replace yours before it wears through to the swingarm.
Designed for quick and accurate alignment, this tool clamps squarely to the rear sprocket so the alignment rod can indicate sprocket alignment with the chain.
Here is a tool to help you remove a few links from a chain that is too long. A great tool to have in your tool box.
The head of the pivot pin you are going to remove must be ground down level with the side plate before using this tool to push it out. Failure to do that will cause damage to the tool that is not covered by any warranty!
Can break or rivet chains from #35 to #530 like a pro.
kit includes a 2mm, 3mm, and a 4mm pin to fit most chains.
kit includes press plates,and all necessary riveting pieces and comes in a durable plastic case.
NOTE: when breaking a chain, YOU MUST grind the heads off of both pins on a link first.
Innovative design that cleans chain from 3 angles at once. Long handle keeps fingers and hands away from chain and sprockets.
Make your life a little easier by having a set of these in your toolbox. Designed to simplify installation and removal of clip-type master links. One tip is shorter and notched to be placed on the pin which allows the longer end to push the clip.
This Motion Pro press tool is a must have when installing and removing Clip-Style master links (520, 525 & 530 sizes).
Easily presses on and off master link plates, works on 520, 525 & 530 Clip-Style master links.
Maximum master link width 24.8mm.
Will not damage master links, hardened steel pins for reliable use.
Light weight billet aluminum construction.
A high quality master link press tool from Wirth Machine used for the removal and installation of master links using a press fit link plate.
Fits 520, 525, and 530 pitch chain.
ULTIMATE SPROCKET WRENCH KIT
Quality components at a great price.
Rotors are laser-cut from high-carbon content 410 stainless steel then lap cross hatch ground and heat-treated. The finished rotors are mounted on a floating black steel carrier for durability and strength.
The oversize floating pins are CNC machined stainless steel rivets with stainless wave washers to ensure they will not crush as more traditional steel pressed rivets can. Finally, high-temp paint is applied to surfaces like cooling holes and edges to provide a clean, finished look.
Includes a fresh set of brake rotor bolts.
Made with heat-treated carbon steel for longer wear life and reduced galling. Stock size, simple bolt-on procedure.
290mm Floating Wave® Rotor
Full floating to ensure optimum brake pad-to-rotor contact. Every high-quality, Galfer-patented Wave® rotor is made from a proprietary mix of virgin high carbon 420 stainless steel, laser cut (never stamped), double disc-parallel ground to assure perfect parallel flatness and heat treated to each specific application. KBA and TUV approved. Seamlessly replaces stock rotor. Full instructions provided along with any technical help needed.
Stock size rear brake rotor laser-cut from high-carbon content 410 stainless steel, then lap cross hatched and heat-treated. Each one then has a high-temp paint applied to surfaces like cooling holes and edges for a clean finished look.
Includes a fresh set of brake rotor bolts.
High quality carbon steel brake rotor.
A great option for every day use, or on your spare rear wheel.
Every high-quality Galfer-patented Wave® rotor is made from a proprietary mix of virgin high carbon 420 stainless steel laser cut (never stamped) double disc-parallel ground to assure perfect parallel flatness and heat treated to each specific application. KBA and TUV approved. Seamlessly replaces stock rotor. Full instructions provided along with any technical help needed! Precision made in their Galfer factory in Spain.
Depending on your application they are designed for street, track and off road. This rotor is for the rider that wants more than what the stock brake system can provide. Longer-lasting extremely predictable and consistent with a drastic increase in lever feel modulation and brake torque.
A fresh set of brake rotor bolts. These bolts already have thread lock compound applied to the threads.
Stock OEM works with factory rotors, comes in a pack of 6.
For aftermarket rotors like Warp 9 or EBC front and rear sets are available.
Front comes in pack of 6
Rear comes in pack of 4.
SMX Carbon Look Rotor
This kit includes a 320mm Wave rotor, caliper relocation bracket and new Galfer semi-metallic brake pads.
You can add a Stainless Steel brake line, and DOT4 fluid to your package.
Warp 9 320mm Supermoto front brake rotor kit. Newly updated and stronger.
Adds serious stopping power to the DR. Included is a new rotor floating on a central mounting carrier along with a caliper relocation bracket.
Available add on options include a Galfer braided stainless steel brake line, and 12oz bottle of Bel-Ray DOT4 brake fluid.
Includes a fresh set of brake rotor bolts.
