This type of flasher is required for LED turn signals. For DC (battery) systems only. Includes 2 female connectors for universal fit.
Not compatible with any DRZ400
Call or Text
+1-541-688-9543Spring time is in full swing here at ProCycle. With these busy days please be sure to let us know if your order is time sensitive. We try to do as much as we can to accommodate your upcoming trip.
The Suzuki DR650 is a long-standing model in Suzuki's lineup, introduced in 1990 as a replacement for the DR600 model. The DR is a 644 cc, 4-stroke, single cylinder, SOHC, 4-valve, air/oil cooled dual-sport motorcycle with a counterbalanced engine that develops 36 horsepower. It has a 13 L fuel tank.
Chain Size: | Front Sprocket: | Rear Sprocket: | Front Tire: | Rear Tire: | Spark Plug: |
---|---|---|---|---|---|
520x114 ('90-'95) 525x110 ('96-Cur) |
16T ('90-'95) 15T ('96-Cur) |
42T ('90-'95) 42T ('96-Cur) |
90/90-21 | 120/90-17 |
DPR9EA-9 ('90-'95) CR10E ('96-Cur) |
This type of flasher is required for LED turn signals. For DC (battery) systems only. Includes 2 female connectors for universal fit.
Not compatible with any DRZ400
The SignalMinder unit is designed as a plug-in accessory for many Japanese bikes. SignalMinder uses a microprocessor to cancel the turn signals at one of three selectable time outs; 10, 20 or 30 seconds.
You can also make it so that all four of your signal lights also act as running lights and establish a dual-channel system on your bike. With the dual-channel system, when you activate the RIGHT turn signal three times in succession, you get 4-way hazard flash lights.
Connecting the 12 volt supply from the brakes to the SignalMinder, also allows for a brake flash option.
There are many options and configurations using this electronic tool.
No wire cutting required. The kit includes Scotchlok connectors to tap into existing wires.
Allows LED type turn signals (and low wattage flush mounts) to flash using a standard flasher unit. Connectors included. One kit works with 4 signals.
The Barkbusters 10 OHM Resistor Set for LED Indicator Lights will correct the flash rate of your auxiliary signal lights. Ready to plug in connectors make installation a breeze. These resistors are intended for Barkbusters LED Indicator Lights.
Features:
This devices allows any two wire after market LED turn signal indicators to operate as running lights (always on), and will blink on / off when the turn signal switch is activated. It is highly recommended to use this product with the Fixed Rate Turn Signal Flasher. This device, as well as aftermarket turn signals, use much less current than stock turn signals, thus an increased flash rate will occur. Load resistors or a fixed rate turn signal flasher will get your flashers operating at the normal flash rate again.
Each package contains two separate adapter boxes, good for operating both turn signals, left and right of either the front OR rear of your motorcycle. You will need to purchase a 2nd kit if doing the Front AND Rear of the motorcycle.
This device is universal; designed to work for any motorcycle with a DC electrical system. Kit comes with bullet connectors to wire in manually. Works with any two wire non-sequential aftermarket LED turn signal indicators.
Fits Most Models
This Diode Kit is only necessary if you have a single dash indicator for your turn signals. One dash light for both left and right signals (such as on the DR650).
This kit allows power to flow in just one direction from the LED signals to the dash indicator light regardless of which direction you are signalling.
These turn signal relocation brackets from ProMoto Billet provide an easy way to move the stock turn signal lights, useful if you find them getting in the way of your luggage configuration.
These brackets may utilize an existing hole in some of the rack side brackets, though many applications will require drilling or fabricating in order to mount properly.
Greatly eases basic chain maintenance, tire changes, parking, cleaning, etc. All necessary hardware is included. Installs using basic hand tools. Tough black powder coated finish.
For riders who wish to run the centerstand and the lowered footpegs we recommend installing a Warp 9 brake pedal. The Warp 9 pedal is arched to give the necessary clearance under the pedal.
T-Rex stands are made from steel tubing finished in black powder for durability. Back by a 3-Year limited warranty for any material or manufacturing defects. Rest assured that you are getting best material commercially available.
Greatly eases basic chain maintenance, tire changes, parking, cleaning, etc. All necessary hardware is included. Installs using basic hand tools.
This kit is for those of you looking for a bit more leg and arm room in the DR cockpit. Included are ProCycle Low Foot Pegs and our oversize bars.
Your choice of an aluminum bolt-on foot pad or a steel weld-on unit. Each will make the footprint of the stock side stand considerably larger, preventing your DR from tipping over in soft terrain. The bolt-on unit is cut from aluminum and then powder coated black, it comes with stainless steel mounting hardware.
The bolt-on pad and does require use of a drill for installation. The weld-on pad will need to be welded to the stand and then the entire unit painted for corrosion protection.
Low peg mounts from JNS Engineering. Your choice of a straight 1.5" drop or get that drop and a 1" rearward offset. You can use your stock pegs or click on one of the optional pegs that are made to fit the stock DR650 mounts.
These heavy duty steel mounts are pressed, welded and then powdercoated black for protection. Includes mounting bolts.
Note: These mounts are compatible with the SW Motech Center Stand by adding a 1/8" spacer behind the mounts.
Made from 1/8" thick stainless steel with dual folded edges for additional strength, these brackets will relocate your passenger pegs down 4" and move them back 1.5". This will give your passenger additional legroom making two-up riding much more comfortable.
All hardware is included for a quick and easy installation.
Low peg mounts for the DR From Wirtz Wire. These are different than our other mounts for several reasons. First, these are designed around the stock pegs. All of the pegs in this section will fit these mounts. Another difference is that these mounts are offered in a low mount as well as a low and rearward mount. These are 'wire EDM' machined from solid 1018 steel bar stock, and are not welded anywhere. They are powder coated black for a great look. Both mounts move the pegs down 2" while the low and rear mounts also move the pegs back 1.3".
Kit comes with new mounts, longer bolts and a longer brake switch spring that will be needed. Pegs are optional, your stock pegs will work.
The upper image shows the low and rearward mounts while the one below that is of the just low mounts. If you look at the two images below that, you will see that these are the low and rearward pegs for both sides of the bike.
Not your average rubber insert! These rubber covers go over the top of your MK3 or MK4 Pivot Pegz so that the aggressive teeth are only exposed when you need them in muddy conditions.
Important to verify which style Pivot Pegz you have before ordering.
Fastway offers a large ADV peg that is 4.75" long and 2.25" wide. With these pegs you can adjust the camber with their patented FKMS Kamber bolt. ´Tilt´ your pegs to increase comfort, or to give better squeeze on your bike. These pegs come with two sets of F3 cleats (one standard, one long). You can order serrated or spiked cleats separately.
These Adventure pegs are offered in several colors, but some colors may require extra time, call for availability.
New from Warp 9. These top of the line Adventure pegs are 5" long and 2.5" wide. They will give your feet the perfect perch whether you are cruising down the highway or standing up hammering down a singletrack trail.
*Does not fit 2021 DR650
Designed and sculpted out of the best 7075 Billet aluminum by Pro Moto Billet elite engineers and machinists. Featuring Fastway's Patented adjustable height, traction, and camber options, the Evolution AIR footpegs are superior in every way. Fastway Evolution AIR pegs are designed to shed mud and debris, while being ultra strong.
You can also order serrated or spiked cleats separately.
These AIR pegs are offered in several colors, but some colors may require extra time, call for availability.
Our complete foot peg assemblies. 1-3/4" lower than stock. No extra brackets that hang down below the frame. Easier on the knees. Wider platform Yamaha YZ style footpegs are stronger and give you firmer footing. Mount solid to the frame. No more 'droopy' feeling when standing on the stock pegs. Lowering your footpegs makes it easier to stand and less of a reach down to the bars when standing.
Now you can get our Low Pegs with MK4 Pivot Pegz or black Fastway ADV pegs (both Yamaha YZ pegs) installed!
Pivot Pegz have set a new standard in footpeg performance and quality, and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty.
Pivot Pegz aim is to build the best footpegs in the world and they really do perform as good as they look. Here's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever.
See below for extenders for these pegs to make them true ADV pegs!
Many riders choose to convert over from the stock 525 to a 520 chain. Besides being lighter and less expensive, a 520 chain is more readily available as well as having more sprocket size options.
Quality steel sprockets and EK SROZ2 525 O-Ring chain. Available in gear ratio choices from - 13/42 to 15/46. EK SROZ2 525 chains come in 120 link length and may have to be cut down to fit. They also come with rivet type master links. Clip type links are available below.
13 and 14 Tooth sprockets require a smaller retainer
This is a complete drivetrain package. All the parts you need to freshen up the most important part of your motorcycle.
High Quality chain. Will need to be cut to fit your sprocket combination.
Lower friction and longer life. X-rings have twice the sealing ability as compared to o-rings. They do a better job of keeping the lube in the links and the dirt out. DID VX chains have a reputation for being the best chain you can buy for dual sport riding. DID VX chains come with rivet type master links.
Quality steel rear sprockets. Choose 525 or 520. 41T to 50T
48 and 50 sprockets require removal or modification of your lower chain guide.
Chain Size Recommendations:
*Actual sprocket color may differ from image shown.
OEM Suzuki seal retainer for the DR650. Simple insurance against your countershaft seal popping out of its bore.
This is not a common problem but for those folks who have had the seal come out it has proven to be quite difficult to get it to stay in place. This steel retainer eliminates any possibility of the seal coming out and ruining your day by coating your rear tire with oil.
The cush hub (sprocket carrier) bearing leads a tough life. This is especially true if your cush rubbers get old and soft. They can allow the chain to pull the cush hub sideways putting a twisting load on the bearing. If there's any question about the condition of your bearing replace it now with this double sealed bearing and quality seal.
This new unit from JNS will protect your cases from the damage caused by a thrown chain, and will also keep your pants, boots or foot safe from your countershaft sprocket.
The case saver portion is laser cut from 0.25" aluminum and then has the 0.19" aluminum countershaft sprocket cover welded to it and the entire unit is powder coated black.
All the mounting hardware is stainless steel with machined aluminum spacers also included.
If you have a 16t front sprocket, mounting modification may be needed to fit. Install the case saver on the bike without the top spacer and bolt. This provides a little extra wiggle room. Add the top spacer and bolt after the bottom bolts are loosely threaded.
B&B fired up the CNC equipment for another beauty, a Front Sprocket Case Saver. A great investment the 6mm aluminum base will protect your engine cases should your chain ever break or derail. On top of that is a 4mm piece to keep your pants and other things out of the chain as well. This replaces the stock cover over the countershaft sprocket.
If you have a 16t front sprocket, mounting modification may be needed to fit.
Replace your lost or broken stock plastic chain guard with a JNS aluminum one. Laser cut, CNC formed, TIG welded, and powder coated a beautiful satin black. This is a direct replacement for the stock unit.
Please note that this unit is a bit wider than the stock one and will have to be trimmed if you are running a big fat SuperMoto wheel/tire.
A real Heavy-Duty Chain Guide manufactured from 5mm (3/16") thick 5052 Aluminum. This guide will take a pounding and continue to put that chain right on the sprocket. The rub block is machined from UHMW plastic and can be positioned to fit just about any sprocket available for the DR. These are powder coated black for a great look and additional protection.
A CNC machined chain guide for the DR. Stronger than the wimpy stock unit and can easily accommodate the stock 525 chain as well as a 46 tooth rear sprocket (by moving the lower rub block to the forward position). The rub blocks are also a higher grade, longer lasting material.
Savvy DR650 owners will remove the upper chain roller. You can use this stainless steel button head screw to plug the threaded hole. Suzuki did not make the upper roller mount strong enough. If you don't remove it yourself the chain will likely do it for you - along with a chunk of metal out of the frame.
Can break or rivet chains from #35 to #530 like a pro.
kit includes a 2mm, 3mm, and a 4mm pin to fit most chains.
kit includes press plates,and all necessary riveting pieces and comes in a durable plastic case.
NOTE: when breaking a chain, YOU MUST grind the heads off of both pins on a link first.
Here is a tool to help you remove a few links from a chain that is too long. A great tool to have in your tool box.
The head of the pivot pin you are going to remove must be ground down level with the side plate before using this tool to push it out. Failure to do that will cause damage to the tool that is not covered by any warranty!
This Motion Pro press tool is a must have when installing and removing Clip-Style master links (520, 525 & 530 sizes).
Easily presses on and off master link plates, works on 520, 525 & 530 Clip-Style master links.
Maximum master link width 24.8mm.
Will not damage master links, hardened steel pins for reliable use.
Light weight billet aluminum construction.
ULTIMATE SPROCKET WRENCH KIT
Quality components at a great price.
A fresh set of brake rotor bolts. These bolts already have thread lock compound applied to the threads.
Stock OEM works with factory rotors, comes in a pack of 6.
For aftermarket rotors like Warp 9 or EBC front and rear sets are available.
Front comes in pack of 6
Rear comes in pack of 4.
SMX Carbon Look Rotor
This kit includes a 320mm Wave rotor, caliper relocation bracket and new Galfer semi-metallic brake pads.
You can add a Stainless Steel brake line, and DOT4 fluid to your package.
Warp 9 320mm Supermoto front brake rotor kit. Newly updated and stronger.
Adds serious stopping power to the DR. Included is a new rotor floating on a central mounting carrier along with a caliper relocation bracket.
Available add on options include a Galfer braided stainless steel brake line, and 12oz bottle of Bel-Ray DOT4 brake fluid.
Includes a fresh set of brake rotor bolts.
Rotors are laser-cut from high-carbon content 410 stainless steel then lap cross hatch ground and heat-treated. The finished rotors are mounted on a floating black steel carrier for durability and strength.
The oversize floating pins are CNC machined stainless steel rivets with stainless wave washers to ensure they will not crush as more traditional steel pressed rivets can. Finally, high-temp paint is applied to surfaces like cooling holes and edges to provide a clean, finished look.
Includes a fresh set of brake rotor bolts.
Stock size rear brake rotor laser-cut from high-carbon content 410 stainless steel, then lap cross hatched and heat-treated. Each one then has a high-temp paint applied to surfaces like cooling holes and edges for a clean finished look.
Includes a fresh set of brake rotor bolts.
DP brakes are available in two different compounds for the DR. The standard Sintered metal material pads provide powerful braking with industry-high HH+ friction rating that is equally adept in wet or dry conditions. They have a quick break-in period and excellent initial response. An oxide-based ceramic material on the rear of the backing plate keeps heat away from the caliper piston and fluid in extreme conditions giving a fade-free performance in even the harshest conditions.
The material in the Special Pads was developed by pro riders in the MX, Supercross, Enduro and Off-Road world where performance and good durability are essential.
Includes front and rear brake pads.
Sintered Pads are best for regular riding. Long life, and good performance in all conditions
Sport Carbon pads are made for fast riding in dry conditions. Not recommended for mud, water, or sand
Race Sintered are designed for racing use
Includes front and rear brake pads
Galfer USA produces several different brake pad compounds for all types of riding styles and uses. With over 60 years of friction material production and research, they have learned that one compound doesn’t always do the trick across the board. If you are just looking for an OEM brake pad replacement or a high performance race brake pad, they have you covered!
Set includes front and rear brake pads.
OEM replacement upgrade. Great feel, long lasting, and very little rotor wear with this durable compound. Compound applications for almost every need, including off road, street, touring, enduro, dual sport and more. Precision made in our Galfer factory in Spain.
Our most popular compound! This compound is the work horse of the Galfer family and is a great OEM upgrade for the everyday rider.
Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
Combines wrench and bleeder valve into one convenient and compact tool
Included in this kit are fork springs, Cogent DDC (Drop in Damper Cartridge) performance cartridges and three bottles of 5w fork oil. Refresh those tired old forks and make them better than new. These DDCs from Cogent are easy to install. No taking the forks apart, no drilling of the damping rods, nothing. Just take them off, flip them over to drain the oil, add new 5w oil, drop in the DDCs and then add the springs and spacers and then install the caps. Preload spacer material is included with the .47 and .70 springs, additional spacers are not needed with the other kits.
This upgrade offers better control off-road as well as on. Less brake dive keeps the fork up in the middle of the stroke on-road and better control off-road whether it be rolling water bars or bouncing off the rocks.
This complete fork upgrade kit includes stiffer fork springs and Race Tech cartridge emulators, as well as a set of top quality fork seals and fork oil to complete the job. Everything you need to transform your mushy stock forks into suspension that really works.
You can select from various straight rate springs or even 'Progressive Suspension' springs to customize the package to your needs.