TW200

The Warp9 oversized front brake rotor kit for the TW200 has amazing brake Performance. This high quality oversized rotor is laser-cut from high-carbon content 410 stainless steel then lap cross hatch ground and heat-treated. Finally, high-temp paint is applied to surfaces like cooling holes and edges to provide a clean, finished look.

*Add the Galfer steel braided brake line for the ultimate braking performance.

Designed to enhance the appearance of your TW200, yet provide greater riding distance per tankful. This larger fuel tank has double the capacity of the stock tank at 3.6 Gallons, yet very slim and sleek. This tank has a custom design that will allow the use of OEM & Maier side covers. These tanks are made with POLYETHYLENE CROSSLINK for extra strength and durability.

Comes with New Screw Cap.

Requires OEM/Stock petcock and oval rubber grommets for install.

If you do not have the grommets or if your O.E. grommets are in poor condition you can add these to your tank order.

An upright Dakar Rally inspired shield designed to protect the rider without interfering with off-road riding. For on-road riding the Rally shield protects the rider’s core from fatiguing air blasts while keeping the head in clean air. Duck behind it in the cold or the rain to keep from experiencing the brunt of the elements. During off-road riding the Rally windshield protects the rider from any amount of mud, dust, roots, rocks, or branches without becoming invasive. Whether standing on the pegs or ducking behind it, you will be impressed at the protection it offers.

The Rally shield for the TW200 is 13 inches tall, 12.5 inches wide at the bottom, 9 inches wide at the top, and made from military grade 1/8 inch cast acrylic in either clear or tint.

ProCycle's custom calendar features specially selected customer submitted photos from around the world. Real riders on real adventures.

Each of the two calendar sizes will feature different pictures. Even more reason to get both!

The desk top is 6" by 3.75" the perfect size to sit on your desk.

The wall calendar is 12" by 18" when fully open for use on any wall. Marks USA holidays and moon cycles.

The three images featured are the finalists in this years photo contest who will all be featured in the wall calendar for 2025.

Heavy-Duty clutch springs

• 15% stiffer than original
• Minimize clutch slip
• Reduce plate wear
• Improve power to ground

Replace your worn out clutch with a high quality Clutch Kit. This kit includes new friction discs for your clutch pack.

Please note: kit includes friction discs only, steel plates and springs not included.

Complete set of friction plates, HD springs and steel separator plates prevent premature driven plate wear, oil muddying and loss of stack height. Built with swaged aluminum carriers that spread the load on the clutch basket and prevent clutch basket "dogging". Anti-swell, alloy impregnated heavy-duty facings for smooth clutch action. Allows modulation, unlike paper clutches which tend to snatch. Don't forget to add a fresh gasket.

Here's another item you might want to replace when you are changing out your front sprocket. Because of it's big back tire, the chain is further away from the center of the engine than most bikes. The engineers at Yamaha decided they had better support the end of the countershaft since it is cantilevered out there so far. They also figured they had better feed some oil out there as well. These Countershaft Seals keep that oil where it belongs, lubricating the countershaft outer support.

Kit includes all seals in the TW200 engine (including crank shaft seals) except valve stem seals. These are high-quality seals made in the USA.

Changing your countershaft sprocket? Here is the gasket you need for the left hand side case cover of your TW200. This is the same side of the engine as your gear shift lever and chain.

Got a little oil seepage or changing out your clutch pack? Here is the gasket you need for the right hand side case cover of your TW200. This is the same side of the engine as your kickstart lever and/or rear brake lever.

Rebuilding your engine? Here is a complete gasket kit for your TW200. Includes: Head Gasket, Base Gasket, Stud Gasket, Head Side Cover O-Ring, two Valve Cover O-Rings, Base O-Ring, Stud O-Ring, Rocker Shaft O-Ring, two Cam Chain Tensioner O-Rings, Intake Manifold O-Ring, two Valve Stem Seals, Exhaust Gasket, Left and Right Side Cover Gaskets, Pump Cover Gasket, TDC Plug O-Ring, Crankshaft Nut Plug O-Ring, and Oil Filler Plug O-Ring.

Leaking Base Gasket? Replacing your worn Rings? Here are the gaskets you need to put your TW200 top end back together after a tear down. Includes: Head Gasket, Base Gasket, Stud Gasket, Head Side Cover O-Ring, two Valve Cover O-Rings, Base O-Ring, Stud O-Ring, Rocker Shaft O-Ring, two Cam Chain Tensioner O-Rings, Intake Manifold O-Ring, two Valve Stem Seals, and Exhaust Gasket.

Here are the O-Rings you need when you perform an oil change. The largest one and the smallest one go inside the oil filter housing cover. The second largest one goes on your oil drain plug. The second smallest one goes on your oil fill plug. Replacing these O-Rings regularly will help keep your engine from seeping oil.

Adjusting your valves or setting your cam chain tension? Here are the O-Rings that fit in the TDC sight plug and the crankshaft nut access plug.

Time to adjust your valves? Here are the O-Rings that fit in your Valve Covers on your Yamaha. Keep the oil inside your motor and grime out! This kit includes both O-Rings. Be sure to grab the feeler gauges and a special wrench to aid in adjusting your valves.

Providing unbeatable performance and exceptional value, Hiflofiltro is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide. The filters are also supplied to original equipment manufacturers as well as private label brands.

Hardened chrome vanadium steel with built in rubber insert to hold spark plug steady.

Thin wall bi-hex sockets designed to access narrow spark plug holes.

Fits 3/8" square drive and hex drive, 14mm, 16mm, 18mm, 21mm.

E3 Resistor Spark Plugs

• Unique electrode shape maximizes the power created by the spark plug – Diamond Fire technology
• Electrode is a combination of performance and technology that results in an improved flame kernel shape
• This flame front ignites the bulk air/fuel mixture faster, moves heat into the combustion chamber faster and creates a more localized pressure front for faster pressure rise during the cylinder power stroke
• The result is more complete combustion and an improvement in engine performance
• A truly premium performance plug
• Sold individually, unless otherwise stated.

Keep your motor running right with fresh spark plugs!

NGK is one of the world's largest manufacturer of spark plugs, whose products are used as original equipment (OE) on countless motorcycle and automobile models.

• High-quality materials and superior construction for serious power and reliability
  • Pure alumina silicate ceramic insulator provides high strength and better heat transfer
  • Deep-seated copper core for a wider heat range
  • Nickel alloy tip for longer life
  • Trivalent metal plating provides superior anti-corrosion and anti-seizing properties
• Choosing the right high-quality plugs prevents fouling from running too cool and preignition from running too hot
• NGK plugs available for almost every application and riding style

Iridium spark plugs are made with premium quality materials.

Iridium plugs last longer than standard ones, meaning you won't have to replace them as often.

• The ultimate in the evolution of spark plug technology and performance from an industry leader
• The iridium electrode is 25% smaller than a platinum electrode, and it's just 1/4 the size of a conventional nickel electrode
• Ultra-small diameter center electrode reduces voltage requirement and extends ignition system life
• Metal shell plating has enhanced anti corrosion qualities

Sold individually, unless otherwise stated.

This Official 2001-up Yamaha TW200 Trailway Factory Service Manual provides repair, maintenance and service information for 2001-up Yamaha TW200 Trailway motorcycles. Most of the information is useful for the 1987-2000 models as well.

• Contains degree wheel, standard unit indicator, adjustable magnetic stand, and three positive stops (10 mm, 12 mm and 14 mm threads)
• Can be used to install and adjust timing of any cam
• Wooden carrying case

Made from medium carbon steel with hardened jaws. It features spanner pins and the jaws open up to 5" wide. It's ideal for holding clutch hubs, flywheels, gears, sprockets, etc. Made by Motion Pro.

This tool is designed to separate vertically split crank case halves on two and four stroke engines. Adjustable arms allow it to be used on multiple bolt patterns found on a variety of makes and models of motorcycles. Industrial grade steel construction with black oxide finish for long service life. Comes with 8mm mounting bolts and 6mm adapters. Protective carrying case included.

For easy removal of recessed oil filters.

Conical point screws pierces and grabs the metal end cap of the filter.

reduces potential damage to the engine cases.

NOT for use on re-usable oil filters.

A 3-pack of easy to apply strips measure the temperature of engine, suspension, and radiator components. Temperature range 149° to 248°

Thread Chasers are designed to clean and re-cut damaged aluminum threads.

This kit contains the two sizes most common on metric motorcycles, M6x1.0 and M8x1.25.

Thread Chasers also remove dirt and metal shavings that become captured in thread grooves.

Uses 8mm or 10mm hex sockets, a Must for all tool kits.

A 'wrench style' tool to turn the 'square top' tappet screws. The wrench does a better job of holding the adjuster screw still while tightening the locknut. Slim and flat, this tool is easy to carry in a tool pack.

• Allows precise valve lash adjustment without disturbing the setting when the lock nut is fastened
• Knurled knob on adjuster drivers ensure a precise and secure grip
• Integrated repositionable wrench handle holds the lock nut while the drivers are used to loosen or tighten the valve adjustment screw

Set includes:

• (1) 10mm steel socket wrench
• (1) 3mm square tappet adjuster

Getting ready to adjust your valves? Here is a set of feeler gauges to make the job a little easier. One tool has .002" & .003" gauges the other has .004" & .005" gauges. Yamaha lists the specs as follows: .002"-.004" Intake and .004"-.006" Exhaust, clearance measured when engine is cold.

• 26 straight blades
• SAE and metric markings
• Check for clearance on valves, ignition points etc.
• Includes 26 blades varying in thickness from .0015"/.038 mm to .025"/.635 mm

• Provides a simple and affordable solution to carburetor tuning problems
• Allows you to tune your bike for increased power and smoothness while retaining fuel economy
• Stage 1: stock engine/filters, stock/modified pipes; about a 5% power increase
• Increases power and driveability
• Fully adjustable

We all love our TWs, but the stock jetting leaves much to be desired! Here is a Jet Kit for your stock TK carburetor to improve your throttle response. Included in the Kit are a wide range of main jets to cover any setup, one Pilot Jet, one Jet Needle, and five Needle Shims. If you have added an exhaust system or ride at higher elevations, this is a great way to tune your TW for your needs.

This is a new Diaphragm Set for your 1987-2000 TK carburetor. If yours has cracked or ripped, here is a replacement.

Here is the O-Ring that fits in the carburetor manifold. This is the manifold that holds the carb up to the cylinder head. The O-Ring mounts between this manifold and the cylinder head. When this O-Ring fails it allows air into your cylinder and makes your Air Fuel ratio too lean which causes the engine to run too hot.

Included in this kit are the parts needed to repair a second generation TK carburetor. You get a new float bowl gasket, needle valve with O-ring, needle, mixture screw, and stock jets for the '01-'21 models kits.

Genuine Keihin spring, washer, and oring for the fuel screw of FCR and FCR MX carbs.

Just the parts…
Fuel screw spring, washer, o-ring (fuel screw not included)

Are you a fan of K&N air filters? Here's one built just for the TW200. Top of line filtering to keep that engine healthy for years to come.

Here's a UNI dual layer foam air filter element to fit our TW200s. Needs to be treated with air filter oil like any other foam filter.

Sold in 6 packs

• Compatible with many air filter boxes. Easy to install by drilling 1’’ holes in airbox housing and snap fitting vents in.
• May be cleaned and re-oiled
• More air flow allows you to add more fuel to your intake mixture, increasing performance.
• 1" Diameter

Not legal for use on pollution controlled vehicles in the state of California.

Yamaha uses this seal material in many places on several motorcycles. It is like weatherstripping and is used to seal up the edges in the TW200 air-box. It seals up the air-box so that water and grime can't enter the air-box from the side. Ensures that air entering the box comes from up under the seat.

Quick release one-piece clamps that saves space. These are great for fuel lines, controlling wires, and can be used many times.

Comes with 4 each of 8mm, 9mm 10mm, and 12mm.

No special tools needed, from Helix Racing.

Fits all TW200's. Includes a new cap and uses the stock petcock. Capacity is 2.7 gallons (stock tank is 1.8 gallons).

  Clarke tanks do not come with a vent hose or vent cap.

Please note: All Clarke TW200 tanks have blemishes due to the mold used in their manufacturing process. Also, side panels are likely not snap into tank as they do on the stock tank.

Designed to enhance the appearance of your TW200, yet provide greater riding distance per tankful. This larger fuel tank has double the capacity of the stock tank at 3.6 Gallons, yet very slim and sleek. This tank has a custom design that will allow the use of OEM & Maier side covers. These tanks are made with POLYETHYLENE CROSSLINK for extra strength and durability.

Comes with New Screw Cap.

Requires OEM/Stock petcock and oval rubber grommets for install.

If you do not have the grommets or if your O.E. grommets are in poor condition you can add these to your tank order.

TechSpec’s Motorcycle Tank Grips were developed to improve body, bike control and increase riders comfort. Gripping your motorcycle between your knees or thighs improves overall control of your ride by better securing your body weight and seat position under the forces of braking, cornering and acceleration while also relieving pressure from your wrists, elbows, shoulders and lower back giving you increased control and a more comfortable, safer ride. Snake Skin is a thin, .125” medium durometer “rubber” material that offers a secure, comfortable grip, durable protection and a clean stock look.

This universal precut kit includes left and right tank grips. (8" X 3") Triangle

These grommets are new Yamaha equipment and are used to help connect your side panels to the fuel tank on any year TW200.

If you are purchasing an IMS fuel tank you may need to purchase a set of these grommets as you will have to reuse your old grommets from the stock fuel tank.

Security for your fuel tank. Includes 2 keys. Internally vented with a check valve that prevents spillage in case of a tip over.

  Fits Acerbis, IMS and Safari tanks only.

A replacement Clarke Gas Cap that fits most Clarke Gas tanks. Comes with rubber gasket.

If you're like us, you hate the long floppy vent hose hanging off the cap of your aftermarket tank.

This one-way vent cap replaces the long hose with a short one only about 2" long. It allows air into your tank but prevents fuel from sloshing out.

Machined from billet alloy and anodized for good looks.

  Not for stock fuel tanks!

Does your stock vacuum operated petcock not shut off when your bike is parked? Replace your stock vacuum operated petcock with this manual one. Must be shut off any time the bike is parked for more than a few hours. Fits stock or aftermarket tanks. Plastic tanks may need the hole 'ovalized' to fit the dual standpipes.

  Does not fit OEM XR650L metal tank

Includes all necessary o-rings and diaphragms

The small size and right angle hose barbs make this filter easier to fit into the small space between your fuel petcock and carburetor. Filter body is only 7/8" diameter. Straight filter is 2" long, 90 degree filter is only 1-5/8" long.

This filter is meant for 5/16" fuel lines. Only 1/2" thick it is small enough to fit just about anywhere.

Fuel supplies can be sketchy at times. This filter lives in your tank to trap dirt and debris as it is poured into the tank. Features a custom shaped adapter that fits securely under the gas cap, creating a leak-proof seal. If it stays out of your fuel, it can't get into the carburetor! Created by the filter experts at Twin Air, this filter fits IMS,  Acerbis and Safari brand gas tanks.

All of these lines are stronger and more durable than vinyl fuel lines and are resistant to swelling, UV light, as well as hardening and cracking.

All of these lines are stronger and more durable than vinyl fuel lines and are resistant to swelling, UV light, as well as hardening and cracking.

Ordering new fuel line? How about a set of fresh zinc plated clamps to go with it?

These will be sure your fuel line stays connected. A pack of 8 clamps in 2 sizes to fit most 1/4 or 5/16 fuel hose.

Hose reducer to go from 5/16" line down to 1/4" line. Many bikes have 5/16" carburetor spigots but most aftermarket petcocks are 1/4". This solve the problem of mismatched sizes. Solid brass construction. Can be used to route or repair fuel lines, oil lines or air lines. Barbed ends provide a secure fit.

Need to mount two containers? A water and a fuel? Two waters? Already have a RotoPax Mount for a single container? Get this extender to work in conjunction with a pack mount and that will be no problem! Single mount, two containers.

RotoPax holder made to mount a single Fuel and/or Water container.

Need to mount two containers? A water and a fuel? Two waters? Get the extender which allows you to stack two containers no problem! Single mount, two containers

RotoPax holder made to mount a single Fuel and/or Water container.

This unique design adds strength and provides extra tightening power.

Use with included base plate or remove plate to attach mount direct by bolting up through the bottom or down through the top.

RotoPax are Rotational Molded - the process which produces indisputably superior products.

• Thicker walls and stronger construction
• Bright colors that are less prone to fading
• Extra threads, thicker walls, and sure-seal gasket guarantee no leaks

Need to mount two containers? A water and a fuel? Two waters? Finally, you can stack multiple packs together! Use in conjunction with a pack mount. You will need to purchase the Single Mount as well as the Extender.

Auxiliary fuel tanks mount to handlebars, forks, or rear racks.

• Suitable for minis, trials bikes, full size bikes, and anywhere else a little extra fuel is needed.
• Each tank includes a siphon kit that connects the tank to the main fuel tank and automatically siphons fuel while the bike is being ridden.
• With this design, the auxiliary tank empties first, before the main tank.
• Does not interfere with headlight, handguards, rear seat, etc.

This Super Siphon has  a (1/2 inch x 6 foot) long hose, which makes it quite easy to transfer fuel from one bike to another! Simply, shake the hose to prime it and get fuel moving. The hose is resistant to gasoline and any other hazardous chemicals. Roll it up, stuff it in your bag and you will be very happy whenever you need it.

Comfortable Oversize (or Fat Bar) Handlebars.

• Black in color. 
• Made from 5mm, proprietary, 2000 series T6 aluminum alloy for superior tensile and yield strength.
• Lighter and stronger than regular bars
• No-crossbrace allows flex to reduce shock and rider fatigue
• Oversize 1-1/8" diameter base reduces to 7/8" to allow standard-size controls/grips
• Etched alignment marks for fast and accurate positioning
• Bar pad included
• Works with stock controls and cables.

For bikes with factory 7/8" handlebars these will require the use of a 7/8 to 1-1/8  adapter (sold separate).

Silver in color

Upgrade your bike with a tapered 1-1/8" bar. Constructed of Aircraft grade 7065 T-6 aluminum that tapers to a standard 7/8" to accept stock controls.

• Lighter and stronger than regular bars
• No-crossbrace allows flex to reduce shock and rider fatigue
• Etched alignment marks for fast and accurate positioning
• Flex Series pad included

This bar kit will raise your hands 5.5" up from the factory riding position. If you are over 6 feet tall, this is the kit for you! It allows for a more natural riding position, no more bent neck and being hunched over the bars. You will be able to ride comfortably and more aggressively by installing this kit.

The ProTaper bars are taller and tapered from 1 1/8" to 7/8" and the braided stainless steel brake line will be a serious improvement to your braking ability. Braking becomes more responsive and firmer while adding a stylish look to your TW200.

Everything you need is in this kit to properly raise your bars:

• ProTaper ADV High handlebar
• PowerMadd 2" bar riser
• Harness extensions
• Longer braided steel brake line
• Longer clutch cable

This kit is for those of you looking for a bit more arm room and a better platform for your feet in the TW cockpit. Included are ProCycle Wide Foot Pegs and our oversize bars with 30mm risers.

• ProCycle Wide Pegs are wider MX style pegs that are much more comfortable when standing.
• These are not only taller bars, but 1-1/8" at the clamp area for additional strength. They taper down to 7/8" on the ends so all the stock controls fit. Black in color.
• 30mm Moose risers that raise the handlebar 30mm.

Kit does not include new throttle tube. If you have 2001 or newer TW200 and would like a new billet aluminum throttle tube, please select the addon box to receive one with your order.

These 7/8" bars fit in the stock clamps and raise your grips a couple inches. They look great too!

• Adapt 7/8" bar mounts to accept oversized 1-1/8" handlebars
• An economical alternative to replacing expensive top triple clamps
• Include mounting bolts.

• 4.75" wide,
• Raises handlebars 2 inches and allows fore/aft position adjustment
• Provides dual pivot points for optimal bar positioning
• One piece design is made from solid aluminum for superior strength
• Available for 7/8" - 7/8" or 7/8" - 1 1/8" bars

Requires 7/8" factory bar clamps on bike

These versatile Risers allow you to clamp a 7/8" diameter handlebar or you can remove the 7/8" reducers and then clamp an 1- 1/8" aluminum "fatbar". If you are thinking of going to a fatbar after you bend your stock set or just want the versatility and option to run any bar, this is the riser to go with. Reducers lock into risers to insure no slippage between components.

These risers use 8mm bolts. Always check and confirm that your bike has adequate cable and brake line length before installing any handlebar risers.

Anti-Vibration Risers may interfere with aftermarket large capacity fuel tanks, and some steering stem clamp configurations (in these cases we recommend using standard pivoting risers).

This unique design from Rox allows you to move your bars either closer (1" up and back) or further away (1" forward and 1-1/4" up) depending on rider preference. These risers have an oblong mounting hole so that they will fit virtually any triple clamp with 8mm bolts. A set of reducers lock into the risers ensuring no slippage whether you have a 7/8" or 1-1/8" bars.

Because these are offset there may be limited clearance between the gas tank and the risers when the bars are fully turned on some models, mainly when mounted to move the bars closer.

Protect your thumbs from blisters caused by riding on the inside of your grips.

Sold in Pairs.

Highly efficient design delivers warmth faster than traditional heated grips.

Choose from the standard five level push button temperature controller, or the LCD display controller which shows the selected heat level and available battery voltage.

The Apollo Heated Grips are designed with an integrated adjustable thumb switch, which allows them to easily fit on any kind of motorcycles on the market. The integrated thumb switch gives control to the rider to adjust the temperature level while keeping hands on the bar for a safer ride.

Its wide temperature setting range will keep the rider comfortable under the cold riding conditions.

The 5 color LED display will enhance the visual look of the heated grips and will allow the rider to quickly know at which heat level the grips are set.

This system will also detect if the battery voltage is too low and will automatically shut down the heated grips in order to make sure the rider have enough power to start the engine or use the motorcycle.

Specifications:

• Integrated thumb switch designed for easy installation and control.
• “Plug & Play” wiring connections to shorten the installation time.
• Wide temperature settings for various weather conditions.
• Low Battery Warning protection to ensure the motorcycle has enough power to start.
• 5 color LED Indicators for the rider to quickly know in which heat level the grips are set.

These heated grips from Koso have been tested by us and we can say they will keep your hands warm and give you the grip you need in off road conditions, thanks to the full diamond grip design.

• Clamp-on grips do not need adhesive
• External temperature controller with 5 heat levels
• For use with twist throttle; includes interchangeable throttle cams
• Requires 35W and draws 2.5 amps per pair; low voltage shut off

These new heated devices are for the user that does not want to commit to changing their grips but still wants to maintain the comfort of heated grips. The fitment is intended to fit all sorts of handlebar sizes. They can be installed and removed in a matter of seconds and kept in any sport bag when not in use.

Features:

• Universal fit to be clipped on any handlebar sizes
• Rubber material that is resistant to outdoor conditions and high temperatures
• Thin and flexible silicone wires make them easy to install

• Ergonomically designed
• Medium-density Thermoplastic Rubber (TPR) compound provides excellent feedback and control, without sacrificing durability
• Full diamond pattern for an unparalleled feel in both wet and dry conditions
• Inner diameter optimized to keep grips secure in any conditions
• 115mm overall length; fit 7/8" bars and throttle sleeves

• Feature the classic Vans waffle sole pattern with a subtle domed center section for improved ergonomics and vibration dampening
• 125mm in length
• Fit 7/8" bars
• Sold in pairs

These grips feature a thicker design that dampens vibration. The soft shoulder allows ease of movement. Three wire-tie grooves are molded into the grip to make securing them a breeze. We think they are great!

ProTaper Pillow Top Grip with 3-D (Tri-Density) Technology.  Try the grip with the technical advantage of three dedicated rubber compounds.

• Vibrasonix pillow top reduces vibration and cushions impact. 
• Inner core compound perfects the bonding interface with bars. 
• Anti-Rip Tip™ uses denser compound to increase life of grip. 
• Designed to self-clean and shed mud away from outer surface. 
• Tacky gel-like surface compound is perfect for the trail and MX.

ProTaper Pillow Top Grip with 3-D (Tri-Density) Technology.  Try the grip with the technical advantage of three dedicated rubber compounds.

The difference between the original Pillow Top and the Pillow Top Lite is the overall diameter of the grip surface. The Lite offers a smaller diameter so the grips don't feel as large reducing fatigue in your hands while riding.

• Vibrasonix pillow top reduces vibration and cushions impact. 
• Inner core compound perfects the bonding interface with bars. 
• Anti-Rip Tip™ uses denser compound to increase life of grip. 
• Designed to self-clean and shed mud away from outer surface. 
• Tacky gel-like surface compound is perfect for the trail and MX.

Each pattern is available in three advanced synthetic rubber compounds. This means you can have the optimum combination of strength, tackiness and shock absorption to suit every riding condition and individual style. Soft grip is extremely soft, giving you a very comfortable ride, great feel and reduces the chance of blisters; however, because the grip is so soft, it wears quickly. Medium is a compromise between firm and soft. Firm grip has the same feel as a stock grip, it is very strong and has very good resistance to tearing and abrasion. Half Waffle has waffle pattern in finger area for traction and diamond pattern on palm side to reduce blisters. Full Waffle: designed after the CR Honda® grip.

This little jewel reduces hand fatigue and cramping on long rides or daily commutes. The Crampbuster is not a throttle locking unit but, rather a simple clip-on device which allows you to relax your grip while riding.

The Go Cruise cruise control mounts over the throttle grip and rests on the brake lever to hold your throttle open, allowing you to stretch and rest your hand on long rides. Installs and removes in seconds with no tools. You can roll off the throttle manually to disengage the Go Cruise.

• Machined and knurled 6061 billet aluminum
• Removable end cap for easy hand guard installation
• Works with standard housing

Here is the little switch that mounts inside your brake or clutch lever perch and controls the brake light or clutch safety circuit. This switch often gets damaged in an unplanned dismount (aka: crash) or the plastic simply cracks from age. When this happens, you can find yourself chasing a short circuit that keeps blowing your fuse every time the brakes are applied. If this has happened to your TW, here's the fix!

Attach this over your brake lever and hand grip, squeeze the brake lever, pull the locking bar in and lock the black portion down. This creates a locked front brake, making parking safe and secure with about 5 seconds of effort.

To unlock the BrakeFix, you just lift the back of the black hooking portion to release it. This takes about 2 seconds. Perfect for use with Snapjack type stands or just parking on an incline.

Replace your Bent or Broken Levers.

• Meets or exceeds OEM specifications
• Made from aircraft A-360 die cast aluminum

  TW200 fitment 1987-2000 year models with Drum Front Brake or 2001-2014 year models with Disc Front Brake.

Here's a set of Shorty brake and clutch levers for your 2001 and newer Tdub.

• Black Alloy levers allow two-finger control of the brake and clutch
• Set includes brake and clutch short power levers

• Warp 9 Flex Levers are machined Billet, anodized and hinged brake levers with CNC machined master cylinder interfaces
• Adjustable reach allows customization to the rider’s hand size
• Double hinge design allows lever to flex out of the way in most impact situations
• Pushrod or Bearing contact styles for smooth brake modulation
• Titanium Pivot / Black levers with laser-etched Warp 9 logo CNC Billet Brake pedal

Replacement folding shift lever, stock length made by IMS.

Did you fall and break your shift lever on your TW200? Replace it with a quality Moose shift lever.

These tips are for the Warp 9 Shift Levers only. 

These are held to the cast Warp 9 lever with a pin and e-clip making them easy to change out. Includes new pin and e-clip in case you lose yours.

You can also order just a new pin hardware kit which comes with new pin and clip.

The Warp 9 shift lever is 7075T6 CNC arm, the Warp 9 logo is laser etched into the finish. 

Includes a black folding aluminum tip and stainless spring and pivot pin for years of rust free use.

1" longer than stock

Direct replacement cables for your T-Dub. OEM or high-quality replacements will keep you on the road or trail. Pay attention to the model year for correct fitment, then select the cable type: Throttle, Clutch or Speedo, they're all here.

• Handy, compact kit for on-the-go emergency throttle, clutch and brake cable repairs
• Includes 2 different diameter 6.5 long inner cables and an assortment of cable ends