High Quality chain. You'll need to cut to fit your sprocket combination.
Non o-ring. Clip type master link.
The TW200 has been offered from 1987- current. The TW200 is powered by a carbureted 196cc single cylinder air cooled engine with 9.5:1 compression mated to 5 speed wet clutch transmission. The TW200 has a seat height of 31.1 inches and a ground clearance of 10.4 inches, making it a very approachable bike for most riders ranging from beginners to veterans. It most notably is known for it's big fat tires, capable of giving excellent traction on most types of terrain.
Click here for additional details on recommended parts, accessories, and modifications.
Year | Chain Size: | Front Sprocket: | Rear Sprocket: | Front Tire: | Rear Tire: | Spark Plug: |
---|---|---|---|---|---|---|
'87-'94 | 428x126 | 14T | 50T | 130/80-18 | 180/80-14 | DR8EA |
'95-Cur | 428x122 | 14T | 50T | 130/80-18 | 180/80-14 | DR8EA |
High Quality chain. You'll need to cut to fit your sprocket combination.
Non o-ring. Clip type master link.
Always carry a spare master link when out on the trail.
Master links are not interchangeable. Be sure to check the manufacturer and series on your chain.
These do not fit the TW200 or XT250. Only for 520 or 525 chains, Please verify chain size.
Clip style master link for the EK 428 O-Ring chain. Keep one in your tool kit for trail side repairs.
High quality sprockets
Counter shaft sprocket replacement requires the removal of the left side case cover. A new gasket may be required. This is also a great time to replace that leaking oil seal!
Replacement retainer if yours is worn out or lost.
This retainer is has a no hassle installation for quick change sprocket swaps with simple readily available tools (pliers and screw driver).
This spring clip retainer takes the place of the OEM two bolt retainer and fasteners when a FRITZCO sprocket is used.
All sizes of new FRITZCO sprockets come with a quick change retainer included, this is only a replacement.
This retainer can only be used with FRITZCO sprockets and can not be used with thin OEM type sprockets.
FRITZCO front sprockets are a straight up no hassle installation. Their sprockets are machined from alloy steel that in every way is comparable to OEM Yamaha and the best offered by other manufactures. The sprockets are then given a heat treatment that provides a compatible sprocket for the Yamaha output shaft and longest chain wear life possible.
We recommend using the Rear Sprocket Bolt Kit when installing most aftermarket sprockets on your TW.
This kit will replace your stock sprocket bolts, nuts and keepers with new hardware.
Many aftermarket sprockets are thinner where they bolt to the wheel and the threads on the stock bolts do not allow these sprockets to be tightened down all the way. These grade 10.9 bolts will alleviate that problem. They are the same length as the stock ones, but the threaded area is longer allowing stock sprockets or aftermarket sprockets to be securely tightened down.
The bolt keepers are genuine Yamaha replacement parts to ensure an accurate fit. It's a perfect upgrade if your keepers have been removed too many times.
Yamaha TW200 heavy duty chain guard.
Made from 3/16" laser cut steel protects stock to oversized rear sprockets.
This unique design bolts in the OEM location but rests against the rear axle bearing spacer for massive impact resistance.
Designed for quick and accurate alignment, this tool clamps squarely to the rear sprocket so the alignment rod can indicate sprocket alignment with the chain.
Here is a tool to help you remove a few links from a chain that is too long. A great tool to have in your tool box.
The head of the pivot pin you are going to remove must be ground down level with the side plate before using this tool to push it out. Failure to do that will cause damage to the tool that is not covered by any warranty!
Can break or rivet chains from #35 to #530 like a pro.
kit includes a 2mm, 3mm, and a 4mm pin to fit most chains.
kit includes press plates,and all necessary riveting pieces and comes in a durable plastic case.
NOTE: when breaking a chain, YOU MUST grind the heads off of both pins on a link first.
This is without doubt the fastest, most effective, most meticulous, precise and systematic method for giving your chain a thorough cleaning. It forces its bristles between the plates where dried and hardened chain lube, road sand, glass, tar and other materials gather to form a hard shield of abrasive dirt where the O-ring meets the chain plates.
Note: Designed to be used with the engine off
Innovative design that cleans chain from 3 angles at once. Long handle keeps fingers and hands away from chain and sprockets.
Introducing Oinker®, the revolutionary chain lube attachment for dirt bikes, street bikes, and ATVs. Say goodbye to messy lubrication. Oinker® attaches to any chain lube or wax, ensuring a precise and even application to both sides of your chain. This means minimal overspray, keeping your swing arm, rear tire, and brakes clean.
*For cans with an attached smart straw, you will need to replace it with the included nozzle
What's Included:
Make your life a little easier by having a set of these in your toolbox. Designed to simplify installation and removal of clip-type master links. One tip is shorter and notched to be placed on the pin which allows the longer end to push the clip.
This Motion Pro press tool is a must have when installing and removing Clip-Style master links (520, 525 & 530 sizes).
Easily presses on and off master link plates, works on 520, 525 & 530 Clip-Style master links.
Maximum master link width 24.8mm.
Will not damage master links, hardened steel pins for reliable use.
Light weight billet aluminum construction.
A high quality master link press tool from Wirth Machine used for the removal and installation of master links using a press fit link plate.
Fits 520, 525, and 530 pitch chain.
ULTIMATE SPROCKET WRENCH KIT