TTR125 (E)

We start with Excel or Sun rims, OEM hubs, and Buchanan's heavy gauge stainless steel spokes. Rims and spokes are precision machined for a perfect match to your bike.

Our pro shop then laces and trues your wheels to perfection, giving you the highest quality set of custom wheels available.

• New OEM hubs with bearings and seals installed
• Excel 2.5" x 17" or Sun 2.75" x 17" front rim
• Excel or Sun 3.5" x 17" rear rim
• Buchanan's stainless steel heavy gauge spokes and zinc-plated nipples

Add tires to your wheel order and we will throw in tubes and mount and balance them at no additional charge.

This kit provides much of the performance gain of the more expensive 150 (143cc) kits. But gives better reliability due to the thicker wall of the cylinder sleeve.

• Wiseco 55mm high compression 11:1 piston, rings, wrist pin, and clips
• HotCams stage 1 performance camshaft
• Includes top end gasket set
• Requires cylinder to be bored to fit the larger piston

This kit provides much of the performance gain of our 130 kit but keeps you legal for racing classes that do not allow motors over 125cc.

• Stock bore size Wiseco 54mm high compression 11:1 piston, rings, wrist pin, and clips
• HotCams stage 1 performance camshaft
• Includes top end gasket set
• Piston fits into the stock bore; requires no modification to your cylinder!

Designed to enhance mid-range and top-end power. Manufactured using the highest quality standards. No core required.

Note: This camshaft has been designed to work with the OEM Yamaha piston, or the BBR big bore kit piston, with OEM sized valves. Any other combination of parts will require that you manually check valve to piston clearance.

Bolt on horsepower! Stage 1: single-cam motor. Excellent midrange and top-end power increase. Uses stock valve springs and rockers.

Fitment Specs: Exhaust Lift: 5.9; Exhaust Duration at 1.00mm: 223°; Intake Lift: 6.8; Intake Duration at 1.00mm: 227°

Designed to improve the life and durability of your clutch, Barnett's "Dirt Digger" provides better rideability with less slippage compared to stock.

• Carbon fiber friction plates
• Tempered steel drive plates go through a vibratory de-burring process and then are quality checked for flatness to provide optimum performance.
• Heavy duty clutch springs are pre-set, shot-peened, and heat treated for performance and durability.

Replacement friction plates and drive plates.

Heavy duty springs help prevent clutch slip in high-performance motors.

• Custom wound from chrome-silicon wire
• Preset for long life
• Higher spring seat pressure to resist clutch slip

If you need a new clutch, you probably need a new gasket to seal that cover when you are all done. Genuine Yamaha part.

High quality stator cover gasket. Genuine Yamaha part.

A head gasket and base gasket to fit the Big Bore cylinder.

GoldPlug is the gold standard in engine protection.

Stainless steel drain plug with an extremely strong magnet that picks up metal flakes in your oil.

12mm Thread, 17mm Head.

• Bolts are CNC-machined from high-quality aluminum
• Embedded magnet helps keep bolt in place
• Pre-drilled holes make for easy installation of safety wires

Hardened chrome vanadium steel with built in rubber insert to hold spark plug steady.

Thin wall bi-hex sockets designed to access narrow spark plug holes.

• Use with 3/8" drive ratchet or wrench
• Choose the one that fits your spark plug size:  14mm, 16mm, 18mm, or 21mm.

Keep your motor running right with fresh spark plugs!

NGK is one of the world's largest manufacturer of spark plugs, whose products are used as original equipment (OE) on countless motorcycle and automobile models.

• High-quality materials and superior construction for serious power and reliability
  • Pure alumina silicate ceramic insulator provides high strength and better heat transfer
  • Deep-seated copper core for a wider heat range
  • Nickel alloy tip for longer life
  • Trivalent metal plating provides superior anti-corrosion and anti-seizing properties
• Choosing the right high-quality plugs prevents fouling from running too cool and preignition from running too hot
• NGK plugs available for almost every application and riding style

This Clymer Repair Manual is an essential resource for anyone looking to service or repair their motorcycle at home. Whether you're riding at the weekend or using your bike for a daily commute, you don't want your plans disrupted - performing regular maintenance is crucial to keep things running smoothly.

Every Clymer workshop manual is the result of a full stripdown and rebuild, allowing you to really know the detail behind your bike. Alongside step-by-step instructions and expert advice, you'll find a wealth of images that help to guide you through repairs and servicing tasks, even on small and complex parts.

What's Included

• Step-by-step instructions based on a full stripdown and rebuild of the bike
• Tips and techniques written by Clymer's motorcycle experts
• A time saving troubleshooting guide with common issues for your motorcycle
• Wiring diagrams for key vehicle systems
• Pictures and illustrations to make tricky jobs easier
• A printed book, dispatched from our US warehouse

(This manual's year range represents the years of coverage available when the manual was written. The vehicle or machine's production years may extend beyond these dates.)

With a Haynes manual, you can do it yourself…from simple maintenance to basic repairs. Haynes writes every book based on a complete teardown of the motorcycle. Haynes books have clear instructions and plenty of photographs that show each step.

• Step-by-step procedures
• Easy-to-follow photos
• Complete troubleshooting section
• Valuable short cuts
• Color spark plug diagnosis

Complete coverage for your Yamaha Trail Bikes covering PW, RT, TT-R and XT225/350 models for 1981 thru 2000.

• Contains degree wheel, standard unit indicator, adjustable magnetic stand, and three positive stops (10 mm, 12 mm and 14 mm threads)
• Can be used to install and adjust timing of any cam
• Wooden carrying case

This holder is the quickest and easiest tool out there to get a grip on that hard to handle hub.

Laser cut to the exact pattern that EBC makes their clutch plates from, it makes loosening and re-tightening the clutch nut a breeze, and minimizes the likelihood of damaging the clutch hub.

Made from medium carbon steel with hardened jaws. It features spanner pins and the jaws open up to 5" wide. It's ideal for holding clutch hubs, flywheels, gears, sprockets, etc. Made by Motion Pro.

• Features 8mm spanner pins
• Jaws open up to 5 inches wide
• Recommended for square tooth style clutch hubs
• Not recommended for v-groove or half round style clutch hubs

This tool is designed to separate vertically split crank case halves on two and four stroke engines. Adjustable arms allow it to be used on multiple bolt patterns found on a variety of makes and models of motorcycles. Industrial grade steel construction with black oxide finish for long service life. Comes with 8mm mounting bolts and 6mm adapters. Protective carrying case included.

Universal 3 bolt flywheel puller.

Complete with hardware kit and adapter for male or female removal.

A 5-pack of easy to use disposable funnels to help make any oil or fluid change cleaner and more precise.

For easy removal of recessed oil filters.

Conical point screws pierces and grabs the metal end cap of the filter.

reduces potential damage to the engine cases.

NOT for use on re-usable oil filters.

A 3-pack of easy to apply strips measure the temperature of engine, suspension, and radiator components. Temperature range 149° to 248°

Thread Chasers are designed to clean and re-cut damaged aluminum threads.

This kit contains the two sizes most common on metric motorcycles, M6x1.0 and M8x1.25.

Thread Chasers also remove dirt and metal shavings that become captured in thread grooves.

Uses 8mm or 10mm hex sockets, a Must for all tool kits.

32-Blade Dual-Reading Tapered Combination Feeler Gauge Set

• 95mm (3.75") long taper blades hardened and polished
• Manufacturer's lifetime warranty
• Dual marked: 0.03-1.00mm and .0012-.040 in.

Tune your stock carburetor for better power and response, easier starting and quicker warm up. Mikuni main and pilot jets.

• Main Jets: #110 & #112.5
• Pilot Jets: #17.5 & #20

Rebuild your crusty carburetor with parts from the same manufacturer the OEM companies use. Included in the kit are all necessary gaskets, O-rings, float valve and jets you need to rebuild your carburetor to like new condition.

Genuine Keihin spring, washer, and oring for the fuel screw of FCR and FCR MX carbs.

Just the parts…
Fuel screw spring, washer, o-ring (fuel screw not included)

The small size and right angle hose barbs make this filter easier to fit into the small space between your fuel petcock and carburetor. Filter body is only 7/8" diameter. Straight filter is 2" long, 90 degree filter is only 1-5/8" long.

This filter is meant for 5/16" fuel lines. Only 1/2" thick it is small enough to fit just about anywhere.

High-performance, high-flow filter element and filter base for the TT-R 125.

• Replaces stock filter and base
• Filter base is made from HDPE plastic
• 3 times larger than stock filter!
• Adds almost 1/2 horsepower
• Designed to fit inside the factory air box

Thick, flat foam, greaseless sealing ring ensures maximum contact with your airbox while acting as a breathable gasket for increased air passage

Features:

• Coarse open-pore foam catches airborn dirt, grime, and sand
• Fine open-pore inner foam acts as second filter to trap the smallest particles while ensuring maximum air passage
• Adhesive withstands repeated cleaning
• Smaller than stock to increase air space and circulation around filter
• exclusively formulated adhesive withstands repeated cleaning. even with harsh solvents or gasoline
• twin air filters are slightly smaller than stock filters to increase air space around the filter and improve circulation

Sold in 6 packs

• Compatible with many air filter boxes. Easy to install by drilling 1’’ holes in airbox housing and snap fitting vents in.
• May be cleaned and re-oiled
• More air flow allows you to add more fuel to your intake mixture, increasing performance.
• 1" Diameter

Not legal for use on pollution controlled vehicles in the state of California.

TechSpec’s Motorcycle Tank Grips were developed to improve body, bike control and increase riders comfort. Gripping your motorcycle between your knees or thighs improves overall control of your ride by better securing your body weight and seat position under the forces of braking, cornering and acceleration while also relieving pressure from your wrists, elbows, shoulders and lower back giving you increased control and a more comfortable, safer ride. Snake Skin is a thin, .125” medium durometer “rubber” material that offers a secure, comfortable grip, durable protection and a clean stock look.

This universal precut kit includes left and right tank grips. (8" X 3") Triangle

Security for your fuel tank. Includes 2 keys. Internally vented with a check valve that prevents spillage in case of a tip over.

  Fits Acerbis, IMS and Safari tanks only.

If you're like us, you hate the long floppy vent hose hanging off the cap of your aftermarket tank.

This one-way vent cap replaces the long hose with a short one only about 2" long. It allows air into your tank but prevents fuel from sloshing out.

Machined from billet alloy and anodized for good looks.

  Not for stock fuel tanks!

You’d be amazed at the dirt and debris that can work its way into your gas can – and from there, your fuel tank. Twin Air’s monofilament screen pocket inserts in your tank to catch particles as small as 40 microns (.00165”) while allowing the gas to flow freely. 

The flange is custom-sized for each modern 4-stroke model to ensure a leak-proof seal. Just remove the filter periodically, turn it inside-out, and clean out the debris that could have been in your engine.

Will not work with factory locking gas caps.

All of these lines are stronger and more durable than vinyl fuel lines and are resistant to swelling, UV light, as well as hardening and cracking.

All of these lines are stronger and more durable than vinyl fuel lines and are resistant to swelling, UV light, as well as hardening and cracking.

Ordering new fuel line? How about a set of fresh zinc plated clamps to go with it?

These will be sure your fuel line stays connected. A pack of 8 clamps in 2 sizes to fit most 1/4 or 5/16 fuel hose.

Hose reducer to go from 5/16" line down to 1/4" line. Many bikes have 5/16" carburetor spigots but most aftermarket petcocks are 1/4". This solve the problem of mismatched sizes. Solid brass construction. Can be used to route or repair fuel lines, oil lines or air lines. Barbed ends provide a secure fit.

Need to mount two containers? A water and a fuel? Two waters? Already have a RotoPax Mount for a single container? Get this extender to work in conjunction with a pack mount and that will be no problem! Single mount, two containers.

RotoPax holder made to mount a single Fuel and/or Water container.

Need to mount two containers? A water and a fuel? Two waters? Get the extender which allows you to stack two containers no problem! Single mount, two containers

RotoPax holder made to mount a single Fuel and/or Water container.

This unique design adds strength and provides extra tightening power.

Use with included base plate or remove plate to attach mount direct by bolting up through the bottom or down through the top.

RotoPax are Rotational Molded - the process which produces indisputably superior products.

• Thicker walls and stronger construction
• Bright colors that are less prone to fading
• Extra threads, thicker walls, and sure-seal gasket guarantee no leaks

Need to mount two containers? A water and a fuel? Two waters? Finally, you can stack multiple packs together! Use in conjunction with a pack mount. You will need to purchase the Single Mount as well as the Extender.

Auxiliary fuel tanks mount to handlebars, forks, or rear racks.

• Suitable for minis, trials bikes, full size bikes, and anywhere else a little extra fuel is needed.
• Each tank includes a siphon kit that connects the tank to the main fuel tank and automatically siphons fuel while the bike is being ridden.
• With this design, the auxiliary tank empties first, before the main tank.
• Does not interfere with headlight, handguards, rear seat, etc.

Quick release one-piece clamps that saves space. These are great for fuel lines, controlling wires, and can be used many times.

Comes with 4 each of 8mm, 9mm 10mm, and 12mm.

No special tools needed, from Helix Racing.

This Super Siphon has  a (1/2 inch x 6 foot) long hose, which makes it quite easy to transfer fuel from one bike to another! Simply, shake the hose to prime it and get fuel moving. The hose is resistant to gasoline and any other hazardous chemicals. Roll it up, stuff it in your bag and you will be very happy whenever you need it.

Aero Tapered Aluminum (ATA) Oversize (or Fat Bar) Handlebar.

• GP High Bend
• Black in Color
• Aerospace grade, heat treated 7075 T6 aluminum construction
• Shot-peened and anodized finish for maximum strength and durability
• Calibration marks for precise mounting
• Clutch-side knurling for maximum grip adhesion
• Stronger and lighter than conventional aluminum handlebars
• Controls the flex to dissipate shock and impact which reduces rider fatigue
• The molded bar pad provides superior impact protection and features and innovative mounting solution for easy installment and positioning
• 1 1/8" clamping diameter tapers to 7/8"at bar ends
• Handlebar is lighter than the competition; it weighs only 1.4lb
• Durable, laser engraved graphics
• 80mm bore depth to accommodate most handguards

For bikes with factory 7/8" handlebars these will require the use of a 7/8 to 1-1/8  adapter (sold separate).

Comfortable Oversize (or Fat Bar) Handlebars.

• CR High Bend
• Black in color. 
• Made from 5mm, proprietary, 2000 series T6 aluminum alloy for superior tensile and yield strength.
• Lighter and stronger than regular bars
• No-crossbrace allows flex to reduce shock and rider fatigue
• Oversize 1-1/8" diameter base reduces to 7/8" to allow standard-size controls/grips
• Etched alignment marks for fast and accurate positioning
• Bar pad included
• Works with stock controls and cables.

For bikes with factory 7/8" handlebars these will require the use of a 7/8 to 1-1/8  adapter (sold separate).

Say goodbye to the frustration of fidgety handguard expansion plugs with Warp 9's innovative Tapped Handlebars. 

These handlebars feature ends that are plugged and tapped with an M8x1.25 threaded insert, providing a secure and reliable mounting point for all aftermarket wrap-around handguards. 

No more worrying about plugs pulling out or spinning during crashes; their robust design ensures you're good to go, even when you encounter obstacles. 

Not using handguards? No problem they've got you covered!Each set of handlebars comes with aluminum grip guards and stainless bolts, offering protection for your grips and delicate throttle tube in case of a get-off. 

Designed with an oversized 1-1/8 inch (28.6mm) clamping diameter that tapers down to 7/8 inch (22.2mm) to accommodate standard controls. Crafted from 7010 T6 aluminum tubing and featuring computer-extruded variable wall thickness, they effectively reduce vibration while enhancing overall performance and comfort. 

Note: Does not include pictured bar mounts.

Mika Metals Hybrid Series handlebars are truly a marvel of engineering. It is the first oversize handlebar in the world that fits on 7/8" clamps. 

The patent pending design is the most unique idea to shake up the handlebar industry in quite some time. They retain all the flex properties of the pro series handlebars and allow you to run oversize bars without the oversize clamps.

Constructed from the highest quality aerospace 7075 aluminum for maximum strength.  CR High Bend, includes injection molded bar pad.

Bars only fit 7/8" clamps

These 7/8" bars fit in the stock clamps and raise your grips a couple inches. They look great too!

• Adapt 7/8" bar mounts to accept oversized 1-1/8" handlebars
• An economical alternative to replacing expensive top triple clamps
• Include mounting bolts.

• 4.75" wide,
• Raises handlebars 2 inches and allows fore/aft position adjustment
• Provides dual pivot points for optimal bar positioning
• One piece design is made from solid aluminum for superior strength
• Available for 7/8" - 7/8" or 7/8" - 1 1/8" bars

Requires 7/8" factory bar clamps on bike

These versatile Risers allow you to clamp a 7/8" diameter handlebar or you can remove the 7/8" reducers and then clamp an 1- 1/8" aluminum "fatbar". If you are thinking of going to a fatbar after you bend your stock set or just want the versatility and option to run any bar, this is the riser to go with. Reducers lock into risers to insure no slippage between components.

These risers use 8mm bolts. Always check and confirm that your bike has adequate cable and brake line length before installing any handlebar risers.

Anti-Vibration Risers may interfere with aftermarket large capacity fuel tanks, and some steering stem clamp configurations (in these cases we recommend using standard pivoting risers).

This unique design from Rox allows you to move your bars either closer (1" up and back) or further away (1" forward and 1-1/4" up) depending on rider preference. These risers have an oblong mounting hole so that they will fit virtually any triple clamp with 8mm bolts. A set of reducers lock into the risers ensuring no slippage whether you have a 7/8" or 1-1/8" bars.

Because these are offset there may be limited clearance between the gas tank and the risers when the bars are fully turned on some models, mainly when mounted to move the bars closer.

Protect your thumbs from blisters caused by riding on the inside of your grips.

Sold in Pairs.

The elegant, open-end design makes these heated grips both stylish and functional. Highly efficient design, delivering warmth faster than traditional heated grips. Five-level temperature controller adjusts the grips accurately to avoid overheating. Specially selected rubber material resists the outdoor environment and provides a secure and comfortable grip. Even at high-temperatures, the grip remains resistant to damage. 

• Removable end caps allow for use as open-ended grips when needed
• For twist throttle applications
• Note: 12-Volt DC applications only.

Choose from the standard five level push button temperature controller, or the LCD display controller which shows the selected heat level and available battery voltage.

The Apollo Heated Grips are designed with an integrated adjustable thumb switch, which allows them to easily fit on any kind of motorcycles on the market. The integrated thumb switch gives control to the rider to adjust the temperature level while keeping hands on the bar for a safer ride.

Its wide temperature setting range will keep the rider comfortable under the cold riding conditions.

The 5 color LED display will enhance the visual look of the heated grips and will allow the rider to quickly know at which heat level the grips are set.

This system will also detect if the battery voltage is too low and will automatically shut down the heated grips in order to make sure the rider have enough power to start the engine or use the motorcycle.

Specifications:

• Integrated thumb switch designed for easy installation and control.
• “Plug & Play” wiring connections to shorten the installation time.
• Wide temperature settings for various weather conditions.
• Low Battery Warning protection to ensure the motorcycle has enough power to start.
• 5 color LED Indicators for the rider to quickly know in which heat level the grips are set.

These heated grips from Koso have been tested by us and we can say they will keep your hands warm and give you the grip you need in off road conditions, thanks to the full diamond grip design.

• Clamp-on grips do not need adhesive
• External temperature controller with 5 heat levels
• For use with twist throttle; includes interchangeable throttle cams
• Requires 35W and draws 2.5 amps per pair; low voltage shut off

These new heated devices are for the user that does not want to commit to changing their grips but still wants to maintain the comfort of heated grips. The fitment is intended to fit all sorts of handlebar sizes. They can be installed and removed in a matter of seconds and kept in any sport bag when not in use.

Features:

• Universal fit to be clipped on any handlebar sizes
• Rubber material that is resistant to outdoor conditions and high temperatures
• Thin and flexible silicone wires make them easy to install

• Ergonomically designed
• Medium-density Thermoplastic Rubber (TPR) compound provides excellent feedback and control, without sacrificing durability
• Full diamond pattern for an unparalleled feel in both wet and dry conditions
• Inner diameter optimized to keep grips secure in any conditions
• 115mm overall length; fit 7/8" bars and throttle sleeves

• Feature the classic Vans waffle sole pattern with a subtle domed center section for improved ergonomics and vibration dampening
• 125mm in length
• Fit 7/8" bars
• Sold in pairs

These grips feature a thicker design that dampens vibration. The soft shoulder allows ease of movement. Three wire-tie grooves are molded into the grip to make securing them a breeze. We think they are great!

ProTaper Pillow Top Grip with 3-D (Tri-Density) Technology.  Try the grip with the technical advantage of three dedicated rubber compounds.

• Vibrasonix pillow top reduces vibration and cushions impact. 
• Inner core compound perfects the bonding interface with bars. 
• Anti-Rip Tip™ uses denser compound to increase life of grip. 
• Designed to self-clean and shed mud away from outer surface. 
• Tacky gel-like surface compound is perfect for the trail and MX.

ProTaper Pillow Top Grip with 3-D (Tri-Density) Technology.  Try the grip with the technical advantage of three dedicated rubber compounds.

The difference between the original Pillow Top and the Pillow Top Lite is the overall diameter of the grip surface. The Lite offers a smaller diameter so the grips don't feel as large reducing fatigue in your hands while riding.

• Vibrasonix pillow top reduces vibration and cushions impact. 
• Inner core compound perfects the bonding interface with bars. 
• Anti-Rip Tip™ uses denser compound to increase life of grip. 
• Designed to self-clean and shed mud away from outer surface. 
• Tacky gel-like surface compound is perfect for the trail and MX.

Each pattern is available in three advanced synthetic rubber compounds. This means you can have the optimum combination of strength, tackiness and shock absorption to suit every riding condition and individual style. Soft grip is extremely soft, giving you a very comfortable ride, great feel and reduces the chance of blisters; however, because the grip is so soft, it wears quickly. Medium is a compromise between firm and soft. Firm grip has the same feel as a stock grip, it is very strong and has very good resistance to tearing and abrasion. Half Waffle has waffle pattern in finger area for traction and diamond pattern on palm side to reduce blisters. Full Waffle: designed after the CR Honda® grip.

This little jewel reduces hand fatigue and cramping on long rides or daily commutes. The Crampbuster is not a throttle locking unit but, rather a simple clip-on device which allows you to relax your grip while riding.

The Go Cruise cruise control mounts over the throttle grip and rests on the brake lever to hold your throttle open, allowing you to stretch and rest your hand on long rides. Installs and removes in seconds with no tools. You can roll off the throttle manually to disengage the Go Cruise.

OE style clutch lever.

• Quality Aircraft grade A-360 aluminum for strength & durability
• Designed to exceed OEM specifications, built to resist breakage
• Durable hard coating
• Designed to fit OEM perch

Attach this over your brake lever and hand grip, squeeze the brake lever, pull the locking bar in and lock the black portion down. This creates a locked front brake, making parking safe and secure with about 5 seconds of effort.

To unlock the BrakeFix, you just lift the back of the black hooking portion to release it. This takes about 2 seconds. Perfect for use with Snapjack type stands or just parking on an incline.

• Warp 9 Flex Levers are machined Billet, anodized and hinged brake levers with CNC machined master cylinder interfaces
• Adjustable reach allows customization to the rider’s hand size
• Double hinge design allows lever to flex out of the way in most impact situations
• Pushrod or Bearing contact styles for smooth brake modulation
• Titanium Pivot / Black levers with laser-etched Warp 9 logo CNC Billet Brake pedal

Fit Disc Brake Models Only

• Bolts directly to the shift shaft, eliminating the need for the stock linkage which can get sticky and is prone to collecting mud
• Hardened splines won’t slip or rotate
• Strong and grippy tip cover
• Folding tips prevent snagging on brush or rocks
• Steel levers withstand impacts and bends without breaking

Folding tip, forged aluminum shift lever from BBR Motorsports. Stronger and lighter than the stock shift lever.

• Bolts directly to the shift shaft, eliminating the need for the stock linkage which can get sticky and is prone to collecting mud
• Strong forged aluminum construction
• Steel knurled folding tip (chrome plated)
• Anodized titanium finish
• 1" longer than stock

• Handy, compact kit for on-the-go emergency throttle, clutch and brake cable repairs
• Includes 2 different diameter 6.5 long inner cables and an assortment of cable ends

The Folding Bar End Mirror has a beautiful case mirror backing plate and the arms are one-piece, eliminating screws and mirrors vibrating loose. The nylon swivel allows just the right amount of tension to be maintained for easy adjustment. 

Features and Benefits:

• Stem Length: 2-1/2 in.
• Fits 7/8 in. handlebars only
• Black
• Sold in pairs
• 3-5/16 in Dia. x 9/16 in Dia

This new mirror screws into your stock mirror mount but can be folded out of the way when it's time to hit the trails. These are quite similar to the very popular KTM folding mirrors but at half the price. Fits either left or right side.

Sold individually. 

  All Yamaha's will need a mirror adapter if you have the stock perch.

One folding mirror. Includes handlebar mount. Can be used on left or right side.

Sold individually.

This new mirror can be folded out of the way when it's time to hit the trails. These are quite similar to the very popular KTM folding mirrors but at half the price.

Fits either left or right side and includes handlebar mount.

Sold individually

With the split back, you don't need to remove your grip or throttle tube, just put it on and tighten 'er down. Put the mirror in and hit the road. Clean and simple.

Replaces all 2 bolt style clutch/brake lever mount clamps. Can help save space on short bend handlebars.

Can't see past your shoulders? These mirror extenders will get your mirrors higher and farther out for a much better view of the road behind you.

Sold individually.

The Adventure Kit is perfect for adventure and touring bikes where the mirrors are kept up most of the time. This mirror offers the widest field of view, and is ideal for riding paved and dirt roads.  The 6 inch arm is a little longer than anything else on the market, for great visibility on loaded bikes.

• Made from super tough glass reinforced zytel
• Reflector Dimensions: 5.25" x 3.5" (135mm x 95mm) 
• Overall mirror length: 7" (175mm) (not including arm mount)
• Convex lens meets SAE and CE specifications 
• Mirror mounts to any 10mm perch.

The new Doubletake ball is oversized, and high quality nitrile rubber surrounds an aluminum base that won't degrade under extended compression. 

The Doubletake Base Kit includes bolts to thread into every application (even reverse thread Yamaha's), without adapters. 

Sold individually.

The Trail Mirror is a simple solution for any dirtbike or mountain bike. Gives you hindsight when you need it, but you forget it's there otherwise. 

• Made from super tough glass reinforced Zytel
• Reflector diameter: 2" (50mm)
• Bar space: 0.75" (19mm), Height 1.25" (32mm)
• Convex lens for wider field of view

Zip ties directly to the bar- no hardware required.

Sold individually

PSR dual sport mirrors come with a slightly convex mirror for a wider field of vision behind you. The round mirror is 4.25" in diameter while the oval is 3.75" x 3". These mirrors are easily adjustable and fold out of the way quickly with the 1" RAM mounts.

The RAM Ball Stud Base used for both mirrors will go into any standard 10x1.25 threaded mirror base.

Sold individually. 

 All Yamaha's will need a mirror adapter if you have the stock perch.

Keep your cables lubed up and working freely, with Motion Pro's Cable Luber. This tool is used to inject lubricant into any cable housing. Clamps over housing and cable allowing an aerosol can with nozzle to be connected. Once the lubrication solution runs out the far end, the cable is lubricated.

Designed to seal completely around the cable housing and stop all those messy leaks. With the unit closed and sealed around the cable, your cable gets better lubrication and you waste less lubricant.

• Works on most cables with a 4mm - 8mm O.D. housing.

Built with the latest in Lithium Ion Polymer Technology. All components are designed, manufactured, assembled and packed in one location assuring high quality and consistency. Besides it's extreme lightweight (50% to 70% lighter than standard lead-acid batteries) it also features a built-in LED test gauge and the ability to mount it in any position. There is no hazardous acid or heavy metals and it is non-explosive and non-combustible.

The Firepower features Increased cranking amps over lead acid batteries and has a very fast recharge cycle and can be brought up to a 90% charge within 6 minutes and also has 6 to 12 times more cycle life when compared to lead acid batteries. A 2-year warranty insures that your investment is protected.

145 CCA 12V/28.8WH
Package Dimensions: 4.75" x 3.00" x 4.50

The Shorai LFM Standard Recommendation is the best overall pick for most applications, and has been selected to give strong cranking performance and long lifespan.

• Capable of holding a charge for up to one year without maintenance
• Two to four times the life of lead-acid batteries
• A Battery Management System that protects the battery from over-discharge.
• Carbon Fiber Composite case
• Stronger cranking for better starts
• Environmentally friendly, just discharge and dispose
• Ultra light and compact

Measures 4.5" x 3.5" x 2.28"
Weight (lbs): 1.34 lbs
Weight (kg): 0.61 kg
Cold Cranking Amps: 135
Polarity: [- +]

Each Shorai battery includes self-adhesive foam panels to achieve a snug fit in your battery box.

The Shorai LFM Duration Recommendation is the best overall pick for most applications, and has been selected to give strong cranking performance and long lifespan. 

• Capable of holding a charge for up to one year without maintenance
• Two to four times the life of lead-acid batteries
• A Battery Management System that protects the battery from over-discharge.
• Carbon Fiber Composite case
• Stronger cranking for better starts
• Environmentally friendly, just discharge and dispose
• Ultra light and compact

Measures 4.45" x 3.5" x 2.28"
Weight (lbs): 1.52 lbs
Weight (kg): 0.69 kg
Cold Cranking Amps: 210
Polarity: [- +]

Each Shorai battery includes self-adhesive foam panels to achieve a snug fit in your battery box.

This is an adhesive-backed foam kit, for the installation of small batteries into larger battery tray areas. Keep in mind that all Antigravity Small Case Batteries DO come with adhesive-backed foam in the box. This kit is for when you need extra foam or are doing installation in another vehicle.

Features

• Hi Density adhesive backed foam
• Help reduce vibration
• Easily cuts with scissors or razor knife
• 3 pieces of 6″ x 3″ x 0.5″ adhesive-backed foam

This is the Restart-Remote for Antigravity RE-START (RS) Powersport Batteries with jump-starting built-in. You no longer need to access the battery to press its Re-Start button in the event you over-discharged the battery. Simply plug this accessory into your Battery’s Charging Cable to remotely awaken the RE-START Battery! No need to remove the seat or a fairing to get to the Battery.

• Compatible with Antigravity RE-START Powersport Batteries
• Plugs into SAE Tip of your existing battery charging cable
• Comes with protective zipper case
• Remote requires 9v battery (not included)
• Not compatible with Automotive Batteries

The LITHIUM US is an advanced microprocessor-controlled charger specially designed to recharge and maintain the cells of Lithium-Iron (LiFePO4)  batteries – maximizing their performance and lifespan. With up to 4.3A of charge current available the LITHIUM US is extremely flexible and will charge LiFePO4 batteries from 5Ah to 60Ah and maintain up to 120Ah.

The operation is simple and charging will commence upon connection. With no need to disconnect the battery from the vehicle, the LITHIUM US will automatically reset any low voltage protection electronics (Battery Management System) fitted. Charging can be restarted manually at any time using the ‘Reset’ button.

The CTEK LITHIUM US is a fully automatic ‘connect and forget’ charger with 8 charging steps including a testing sequence to show if the LiFePO4 battery can take and retain the charge, a unique maximization step to restore full capacity, and patented maintenance charging to ensure maximum performance even after months of inactivity. Splash-proof and dust-proof (IP65) the LITHIUM US is easy and safe to use, protects vehicle electronics, is spark-free, is reverse polarity protected and short circuit proof. The LITHIUM US features a 5-year warranty.

The CTEK Brand of chargers is recommended for all Antigravity RE-START (RS) Batteries (models with built-in jump-starting and full BMS protections)

Spare Extension Cable Set for Shorai 12V LFX battery charger.