TTR125

GET JumpStarter Mini, the second-generation, multifunctional jump starter. Now lighter and smaller, it's ready to help you restart any motorcycle or scooter when the battery is low. You can also use the powerful built-in LED flashlight or charge your use it as a power bank to charge your electronic devices. JumpStarter Mini comes together with a hard, water-resistant case perfect for carrying it anywhere and protecting it on your journeys.

• Light and compact multifunctional mini starter
• Allows restart of motorcycles and scooters when they are out of battery
• Can also be used as a Power Bank for electric devices thanks to the USB output port
• USB 5V2.4A output allows connection to tablets, smartphones, MP3 etc.
• Has built-in LED flashlight
• Easy to use; provides special protection against overvoltage and inversion of power supply polarity
• Start current: 200A, peak current: 400A, operating temperature range of -20°C to 60°C
• Includes JumpStarter, Smart Cable, 3-in1 USB cable and user instructions
• Measures 155 mm x 79 mm x 16 mm

A portable device that can jump-start your motorcycle or car. It can also charge your cell phone, GPS unit, laptop or other electronic devices via USB cable.

• XP-1 is 6" x 2 7/8" x1" 14oz.
• XP-3 is 5" x 2 7/8" x 1" 12oz.
• Holds a charge for up to 1 year.

Complete replacement CDI unit for the TTR125. Enhanced power curve. 1000 RPM higher rev limit. Easier starting, crisper throttle response.

The Speedo DRD corrects and fixes the speed signal after it was altered by something else, such as sprocket changes or tires size changes or transmission changes.

The Universal Kit does require some basic wiring to install. It's fairly easy, and only 4 wires; [positive, ground, signal-in, signal-out]. Universal Kit works for Cars, Trucks, & Motorcycles with digital odometers, and 3 wire speed sensors.

• Smallest electronic speedometer/odometer calibration device in the world
• Simple plug-in installation
• Weather proof design to protect against the elements

• Mini Speedometer is only 2 inches diameter.
• Works with Japanese speedometer or odometer cables.
• Mounts to handlebar bolt or use the bar clamp supplied.
• Illuminated dial for night riding.
• Smaller, lighter and more accurate than the stock unit.

The Trail Tech Vapor Speedometer/Tachometer units are custom designed for an exact fit. They feature a bright white backlit LCD display, waterproof connections, and all parts needed for a complete installation. These units accept AC and DC power input, and automatically switch to internal power if external power is removed. Power connectors are included. Permanent solid-state memory guarantees that data is never lost, even without power. Units are available in black.

Trail Tech provides a one year warranty and unlimited free phone and email support.

Unit functions:

• Speedometer
  • Current Speed
  • Maximum Speed
  • Selectable MPH/KMH Display
• Tachometer
  • Real-Time RPM Bar Graph
  • Numeric RPM Readout
  • Dual Programmable Shift Lights
  • Up to 20,000 RPM
• Temperature
  • Ambient Temperature
  • Engine Temperature (liquid cooled only, optional air cooled sensors available)
  • Dual Programmable Temp Lights 
• Distance
  • Adjustable Distance
  • Permanent Odometer
  • Selectable Mile/Kilometer Display
• Clock
  • Hour Meter, Stop Watch, Ride Time
  • Accumulated Ride Time
  • Permanent Hour Meter

Keep your smartphone, GPS and/or MP3 charged while enjoying your ride. Water- and weather-resistant, the Dual USB Port/Plug Charger offers you 5-Volt/2-Amp dual USB ports that have an inline fuse for protection. It comes with 38" of wire and 12" long battery quick connect rings. The mounting bracket that is included fits 7/8" and 1" bars.

The Optimate Cable O-20 is a SAE weatherproof bulkhead/panel mount power source. Main body fits a 1" dia. hole. Overall length of the unit is 12" from top of bulkhead to end of connector. Both connectors are industry standard 2-pin SAE connectors. We also offer an optional stainless steel bracket that you can bolt on wherever you like. This makes a clean installation and you won't have a charging cable hanging loose.

Cable max. rating is 10 Amps. Includes an in-line rubber seal at the connector end and a protective cover at the bulkhead for when you don't have something plugged in. Unit has a 3-year limited warranty.

Don't have an SAE plug attached to your battery? Choose the add on below.

This USB device connects to a battery cable with an SAE connector just like the typical Battery Tender outlet, and allows you to charge your electronic devices. Input is 12 Volts, with an output to the USB port of 2.1A maximum, perfect for your phone or other USB devices.

Laser cut from stainless steel. This is a quick and easy bracket for mounting a key switch, panel mount, bulkhead fitting or anything that requires a 1 inch hole.

Open Trail Terminal Tender blocks allow you to add up to six different accessories on your battery.

Features:

• Fits any 12v powersports battery with square posts
• Three mounting options: side, front, and top
• Includes two blocks (+) and (-) and 8 button head bolts

The standard ring connector is a simple, quick connection with a fused positive ring cable and negative cable that attaches directly to your battery with an industry standard 2-pin, SAE connector.

The weather protected ring connector is a premium quick connect permanent battery lead with weather protected connection system and cable. It features 1/4"/M6 ringlets, 20" L, Industry standard 2-pin, heavy-duty SAE connector, 15A fuse, Cable max rating: 5 Amps, Cable remains flexible at below freezing temperatures; rated for -40°F/-40°C.

• Permanent battery leads with integrated battery status/charge system monitors for 12V lead-acid batteries or lithium batteries
• Monitor charge or confirm if the charging system is working correctly
• SAE charge port with weatherproof sealing cap
• Two automatic modes: battery charge level monitor and charging system test

This bright and compact 6-LED flashlight plugs right into your SAE battery charging socket for hours of light. In addition, it has a charging system check that lets you know if your bike is charging properly. It features a 40 inch cord so you can see in those out of the way places when you need to.

Small 2 3/4" diameter motorcycle horn. Works on 12v DC. Sound will be diminished when running on AC.

• High sound level 105-118 db
• 80mm diameter and only 7.5 oz
• Wire extension included
• Universal for street and off road use

Deltran quick-connect plug with LCD voltmeter display. Plug this into your Battery Tender, or any SAE cable, for an LCD display of the battery voltage. Three LED lights indicate the state of charge as well.

A digital voltmeter that can be mounted almost anywhere, on any bike, thanks to ProCycle's multi-position stainless steel bracket. Keeps you informed on the status of your charging system.

Completely waterproof and comes with connectors, wires and thorough instructions. A "must have" device for riders who use heated riding gear, heated grips, additional lighting, GPS, etc.

• Compact, adhesive back
• Easy-to-read display
• Flashing low voltage warning
• Measures 1.57" diameter x .43" D
• Effective temperature range: 14 ~ 140 °F

So you say you want more light for your dual sport? Give this 7"DOT legal Rally light a try and light it up like a freight train! HIGH/LOW operation and SAE/DOT/E4 approved. 
 This light does not have the large Cyclops logos shown on one of the images.

• Race Inspired Design
• Hella reflector, made in Germany  stamped SAE/E4
• Lightweight Aluminum Frame
• Plug and Play for Bikes with H4 Bulbs.
• Available with optional mounting plate for computer or GPS
• Easily converted to HID if desired, uses an H4 bulb
• For bikes that are not H4 (XR650R), a simple H4 plug available at any auto parts store will allow you to use this light.
• Now the panel on top of the light for mounting speedos/gps's etc is included, (This is a platform, not actual GPS mount.)

Optional 10.0 Lumen LED High/Low Upgrade  and now the Phoenix LED complete headlight for the ultimate DOT headlight
The stock lamp that comes with this rally light is great, but you can get  well over double the brightness  with the LED upgrade at a substantially lower power draw. Note if your bike is ac powered at the headlight you will need the rectifier for the LED option.. AKA carbureted KTM's CRFX and XR400/650.. others may apply.

Each 10 watt Solstice Solo produces 900 lumens, which is roughly equal to a 50 watt halogen bulb. These are one of the brightest LED off road lamps on the market. The rugged and compact 2” x 2” square die-cast aluminum housing makes mounting easy. The Solstice Solo also features a 4 sided channel design that allows you to interlink it on all four sides with other Solstice Solo pods. Includes stainless steel mounting bracket and waterproof connection. Choose narrow, medium, wide or elliptical light beam pattern. Our favorite is the Elliptical pattern which is wide and flat, putting most of the light where you need it the most.

Sold each.

A game changer in auxiliary lights. High output, compact and lightweight!

The New Cyclops Aurora 2 inch lights rated at 4000 lumens combined. Using an authentic top binned Cree XHP50 emitter these lights pack a punch!

Available with or without the daytime Running light option (DRL) which can also be a front blinker. (you may need an LED flasher to do that)

Like all Cyclops lights we only use the Best Real Cree emitters. R113, R10 TUV and Emark certified IP68 rated.

Includes a full relayed wire harness designed for a Motorcycle. No need to use a switch if running the DRL version, also no need for a switch if using the skene dimmer or want the lights on in high beam and off in low beam. The factory switch will work for these applications. Unless you have a LED factory headlight in a R1200gs, 850Gs, or KTM1290 these bikes will require our Raider canbus controller.

Look at these quality features!

• Solid Steel cradle mount. No broken or cracked mounts!
• CNC machined aluminum housings
• Polycarbonate lenses, Break-proof!
• 15 degree beam patterns, a great choice for distance and field of view.
• 19 watts each
• 2000 lumens a piece, 4000 lumens for the set.
• Includes a relayed wire harness
• Input voltage 9-30VDC
• R113, R10 TUV and Emark certified
• IP68 Rated

Available in two wattage configurations: 30 watts and 42 watts, which produce luminous outputs of 5000 lumens and 7000 lumens, respectively. If your motorcycle's electrical system cannot accommodate these wattages, the light can be operated in low beam mode, resulting in a 50% reduction in power consumption. When additional illumination is required, users can easily switch to high beam mode.

Despite its compact size, this LED light is designed to deliver substantial luminous output. Its performance surpasses that of other mini LED lights in the market.

The light is equipped with a durable push-button switch, metal handlebar mounts, and adaptable options that allow for compatibility with various motorcycle configurations. It features components such as switches, cords, strain reliefs, and optics that are engineered for enhanced water resistance, robustness, and overall performance.

Tailored specifically for snowbike applications, this light boasts a compact design with significant output capabilities. Enhanced heat is directed to the lens, facilitating snow melting and enabling continuous riding.

This light is ideal for users seeking a lightweight solution to comply with legal requirements for headlights while also being sufficiently powerful for racing and trail riding.

Installation is straightforward, with the light mounting easily to a number plate; however, the use of the recommended stainless steel platform mount is advised for improved convenience. The light operates using the motorcycle's battery power.

The Explorer light bar is equipped with a GoPro-compatible mount and an aluminum platform, allowing for versatile mounting options. A handlebar mount is provided for central positioning on the handlebars. (Fits all stock 7/8 and 1 1/8 bars. Not for flexbars) Notably, there are no plastic components in the light head assembly.

Included with the product is a rubber-covered switch that can be mounted on the handlebars, offering three power settings: off, 50%, and full brightness.

The light features a combo beam pattern, integrating spot, driving, and wide beam configurations into a single unit.

Now a lifetime warrantied LED light set at a budget friendly price.

The new Cyclops Pegasus led light set comes complete with a high quality relayed wire harness and a potent combo light beam pattern.

We are able to offer this fantastic light at a great price due to a one piece optic and sealed beam construction, eliminating extra parts and creating a very durable and high performance light.

These lights in white feature 7 watt emitters (28 watts per light) with two 10 degree and two 25 degree optics, Good for 500 plus ft of lighting (white).

The amber version is a Cree 3 watt emitters (12 watts per light).

This combo beam pattern offers good forward lighting and extremely good conspicuity.

The light set is available in white 5600K or a extremely bright Amber, perfect to allow those autos to see you. Lightweight and robust at 2.75 inches with a single stud mounting, they fit just about anywhere you would like to mount your lights.

Specs:

• Canbus compatible, full relayed wire harness included
• 5000 plus lumens for the set
• 28 watt draw per white light, 12 watt draw per amber light
• ISO 67... waterproof
• 5600K (white 33% brighter than Amber)
• Life time warrantied
• Sold as a pair

The Mojave Series LED Racing Lights have been designed to survive and operate in extreme conditions. Lights feature a heavy duty housing that can withstand hard impacts and a lens that is twice as thick as traditional lights. The light includes three different replaceable lens (Flood, Spot, and Combo).

Features:

• Heavy Duty Design​
• IP69K Rating​
• Flood, Spot / Flood, & Spot Lens Included
• Stainless Steel Bracket & Hardware​
• 5,000k Light Color – Natural Daylight
• Heavy duty black steel left & right mounting brackets to bolt directly to your lower triple clamp.
• Harness with Switch

This kit will work with the 6.6 Gallon Acerbis fuel tank for the DR650. You must run the light brackets inwards in order for there to be proper clearance with the 6.6. Gallon tank.

This kit includes 2 auxiliary light mount brackets. These brackets are designed to mount to most lower triple clamps. New longer bolts are supplied to accommodate the thickness of the bracket. These brackets are powder coated black for a sleek and long lasting finish. The brackets can be used to put the addition of new lights to the outside of your forks or swap the brackets and the lights can be mounted inward to give more clearance for bigger shrouds or fuel tanks.

The perfect solution for mounting those LED auxiliary lights. The base of the RAM mount is held by your mirror. This puts the light where you can easily adjust the angle for different riding situations. This mount fits VisionX Solstice lights or any other light with a 6mm or 1/4" hole in the mounting bracket.

This is for Mount Only. Sold individually.

10 Watt LED lights sold separately.

This frame includes six, white, full-spectrum LED bulbs on a 6-inch strip for bright illumination of your license plate. It is made in a sturdy cast aluminum, and is powder coated with a durable black finish.

Outside frame dimensions are 7.25" in. wide by 4.2". Center to center mounting hole distance is 5.7 in. All mounting hardware is included.

License plate light with 5 LEDs. Compact and easy to mount. Meets plate illumination requirements with super white light.

This is for the LED license plate light ONLY.

• Waterproof, long-lasting marker light bar uses less power
• Features 180° visibility
• White LED color
• Can be used in any position; refraction of light depends on position
• Measures 38mm x 9.8mm x 18mm
• Not for use where DOT lighting is required.

License plate bolt with bright white LED light. The simple way to light up your plate.

Clear lens, amber LED type lights. Short flexible stems. Very small, only 2 7/8" long. Requires a LED turn signal flasher to flash properly. 4 Pack

Eight ultra-bright amber LED lights in a sleek design. Flexible stem helps absorb the occasional hit. Available in 2 pack or 4 pack

Recommended to use resistor for proper turn signal flash rate.

Specifications

• Comes with mounting hardware.
• Measures 4" long with base and 1" wide at the lights.

Easily turn your blinkers into additional running lights and brake lights (rear) for added visibility.

White light in the front and red in the rear. Rear red running lights and bright red brake lights. You can omit the running and brake lights if you wish and still have the best blinkers on the market.

Dazzling bright Amber blinker functions. 

Everything comes in a spring-loaded stock designed to keep it safe from those unexpected tip-overs, crashes, or encounters with brush and trees. They’re flexible enough to bend 360 degrees, yet tough, durable, and almost impossible to break!

If you have a single indicator light for the blinkers that is not built into the display and is not LED you will need the diode kit (AKA DR650) If it is built into the speedo display it should not require the diode kit.

Available in a generic kit with Bullet connectors supplied. Great for your DR or almost any other bike with a single post blinker setup. These will work well on bikes that use a flasher, but you might have to add the female side of the connectors that are included in the kit.

Not for Yamaha T7, see model specific listing

These signals have short rubberized flexible stems and bright mini halogen bulbs.

• Ministalk Marker Light V-Shape - Black/Amber
• Size:  2-5/8"
• Single-filament bulbs
• Sold in pairs

The Barkbuster LED Indicator Lights for Jet, Storm & VPS Plastic Handguards to increase your visibility and safety using 15 high intensity LEDs that mount directly to the plastic handguard shells. Super bright auxiliary signals will make your directional intentions clear to upcoming traffic. The LED indicators are very low draw and E marked for road use.

Features:

• High intensity LEDs with amber lenses
• Intended for use as indicators/turn signals
• E mark approved for use as an indicator light
• 15 LEDs per indicator amplifies your visibility to other traffic
• Enhances safety by imrproving clarity of planned directional changes
• Very efficient performance with low power draw
• Designed for use on the upper surface of Barkbusters Jet handguard plastics
• Compatible with the upper and lower surface of VPS & Storm plastics

What's in the box:

• Barkbusters LED indicators in amber (pair)
• Mounting materials
• Installation instructions

Please Note: Not compatible with the electrical system on the Honda Africa Twin CRF1000L

Ultra bright amber LED turnsignals offer nearly the same visibility as OEM in a much smaller package. 15 amber LEDs in every signal. Flexible rubber stalks. Requires a LED turn signal to flash properly.

Pack of Two

These Sequential Turn Signals are available in a 2 pack or 4 pack short stem with 7 LEDs.

Matte Black, plastic body with smoke lens and 8mm mount bolt.

Specifications

• E-marked.
• Short Stem: 75mm x 15mm

Triangle/Teardrop style signals with LEDs. Mounts on any flat surface to keep out of the way of brush, branches, and your exhaust system. Requires LED flasher or LED turn signal resistors to flash properly. 

• Fits on the fender with screws for secure installation
• Rubber mount base fits even curved surfaces
• Terminals and bolts are included for installation
• Comes in pairs
• Works on 12V AC/DC

This Diode Kit is only necessary if you have a single dash indicator for your turn signals. One dash light for both left and right signals (such as on the DR650).

This kit allows power to flow in just one direction from the LED signals to the dash indicator light regardless of which direction you are signalling.

You may have noticed after adding aftermarket turn signals (especially LED units) that your blink rate has significantly increased. OEM flashers are designed for standard bulbs which draw a few watts each, much more than typical aftermarket bulbs or LED signals. This device is an effective alternative to using load resistors because it consumes considerably less watts, consumes less space, and does not generate excessive heat.

The plug is exactly the same as the OEM unit making swap outs a cinch. No wiring changes, cutting and adding connectors. Just plug it in and you will have a steady flash at the DOT OEM rate regardless of what signal bulbs you use. It is an all solid state design and will blink correctly with loads all the way down to 0.1W / 0.01A.

  Not for any DRZ400 or Royal Enfield Himalayan

This type of flasher is required for LED turn signals. For DC (battery) systems only. Includes 2 female connectors for universal fit.

  Not compatible with any DRZ400

Works on AC and DC lighting systems

  Not compatible with any DRZ400

Allows LED type turn signals (and low wattage flush mounts) to flash using a standard flasher unit. Connectors included. One kit works with 4 signals.

The Barkbusters 10 OHM Resistor Set for LED Indicator Lights will correct the flash rate of your auxiliary signal lights. Ready to plug in connectors make installation a breeze. These resistors are intended for Barkbusters LED Indicator Lights.

Features:

• 10 OHM
• Intended for Barkbusters LED Indicator Lights
• Corrects flash rate of LED signals
• Flash rate: 90 (+/- 30) times per minute

This devices allows any two wire after market LED turn signal indicators to operate as running lights (always on), and will blink on / off when the turn signal switch is activated. It is highly recommended to use this product with the Fixed Rate Turn Signal Flasher. This device, as well as aftermarket turn signals, use much less current than stock turn signals, thus an increased flash rate will occur. Load resistors or a fixed rate turn signal flasher will get your flashers operating at the normal flash rate again.

Each package contains two separate adapter boxes, good for operating both turn signals, left and right of either the front OR rear of your motorcycle. You will need to purchase a 2nd kit if doing the Front AND Rear of the motorcycle.

This device is universal; designed to work for any motorcycle with a DC electrical system. Kit comes with bullet connectors to wire in manually. Works with any two wire non-sequential aftermarket LED turn signal indicators.

• Eliminates the need to cut and splice wiring when using aftermarket turn signals or marker lights
• Plug into the OEM turn signal plug and then use bullet style connectors used on aftermarket lights
• To verify proper fitment, compare connector photos to OEM connector
• Sold in pairs

These turn signal relocation brackets from ProMoto Billet provide an easy way to move the stock turn signal lights, useful if you find them getting in the way of your luggage configuration.

These brackets may utilize an existing hole in some of the rack side brackets, though many applications will require drilling or fabricating in order to mount properly.

Replacement Halogen bulbs for mini style turn signals. Sold in a pack of 5 bulbs.

Roll-up pouch ideal for tucking away your lights when out on the trail.

Installing new turn signals or brake lights and need to find the 'HOT' wire, or are you just trying to find out if a specific wire has power going to it? Either way, this test light can help you locate shorts, open, and voltage on 12-24 volt DC circuits.

Inexpensive way of getting the factory look. Adds 1/2" of width to any standard foot peg. These will give you a much more stable platform when standing on the pegs.

Sold in pairs.

Not your average rubber insert! These rubber covers go over the top of your MK3 or MK4 Pivot Pegz so that the aggressive teeth are only exposed when you need them in muddy conditions.

• Unique, innovative design
• Wide flat platform
• Openings allow mud/dirt to pass through
• Easy and quick to get on/off
• Good grip
• Reduced vibration
• Extra comfort

Important to verify which style Pivot Pegz you have before ordering.

Light weight and strong. These DRC foot pegs have a wider platform for increased comfort and control. Cast from Chromoly steel for unbeatable strength and durability.

Services two Pivot Pegz and fits MK2, MK3 and MK4 Pivot Pegz

Kit Contents:

• Two pivot tension springs
• Two lock nuts
• Two washers
• Six o-rings
• Two split pins
• Pivot Pegz sticker and instruction sheet

• Designed to quickly and precisely remove outer bearing race from the steering head without the use of a hammer and punch
• Puller design ensures bearing is pulled perfectly straight to eliminate possible damage to frame
• Works on all tapered bearing races from 47 mm to 55 mm OD
• Precision machined anodized aluminum cup will not damage seal surface
• Brass bearing washers for easy use and long life
• Hardened steel jaws engage securely on inner bearing lip
• Lifetime limited warranty

High-quality DID chain and steel sprockets for 2002 & later TTR125s.

• 13T front sprocket
• 49T or 54T rear sprocket
• 130-link DID chain (must be cut to correct length)
• Note: 2002 and later models have 10mm sprocket bolts.

428 x 130 links. High Quality non-ORing chain. Rust-resistant gold plated chain for high powered racing machines.

Always carry a spare master link when out on the trail.

  Master links are not interchangeable. Be sure to check the manufacturer and series on your chain.

These do not fit the TW200 or XT250. Only for 520 os 525 chains, Please verify chain size.

For all years.

• Machined from impact and wear resistant chromoly steel
• Heat treated, then finished with a nickel coating for corrosion resistance

Rear Sprocket

Note: 2002 and later models have a 10mm sprocket bolts. 2000-2001 models have 8mm sprocket bolts.

Black anodized 49 tooth 7075 T651 aluminum sprocket.

Fully encloses the chain to guide it onto the rear sprocket. Stainless steel hardware, anodized aluminum plate, and plastic buffer for low friction and noise. Saves expensive engine cases.

Reduce the friction dragging down your drivetrain.  This chain roller is made from Delrin®, it's self-lubricating and a significant improvement over stock. 

Does not use a bearing but rides directly on the frame boss. There is no mounting hardware included.

• Accurately and quickly measures chain slack
• Two scales measure both chain slack and chain to swingarm clearance
• Setting chain slack properly dramatically improves chain life
• Lightweight compact design fits easily in your tool box or road kit
• Works on most street and dirt bike applications up to 75mm chain slack
• Made from engineered nylon with aluminum measuring scale
• Anodized laser-etched precision measuring scale
• Refer to your owner's manual for proper chain slack and procedure
• Patent pending

Designed for quick and accurate alignment, this tool clamps squarely to the rear sprocket so the alignment rod can indicate sprocket alignment with the chain.

Here is a tool to help you remove a few links from a chain that is too long. A great tool to have in your tool box.

The head of the pivot pin you are going to remove must be ground down level with the side plate before using this tool to push it out. Failure to do that will cause damage to the tool that is not covered by any warranty!

• PBR = press, break, rivet
• Innovative design will press, break and rivet 520, 525 and 530 chains with one convenient tool (not for use on 428 chains)
• Versatile design will remove chain pins, press master-link plates and rivet hollow nose and soft nose (quad stake) master link pins on O-Ring and non O-Ring type chains
• Easy-to-use design allows you to change tool functions by simply moving the position of the anvil block
• Indexing letters on movable anvil and body ensures correct tool configuration; simply line up the letter on the anvil to the letter on the body to get the configuration you need
• All components conveniently store on tool when not in use
• All steel construction with heat-treated components for strength and durability
• May be supported in a vise or held with included handle
• Great for the professional technician or DIY mechanic
• Compact and light enough to carry in a tool bag for trail-side repairs
• Patent Pending

Can break or rivet chains from #35 to #530 like a pro.

kit includes a 2mm, 3mm, and a 4mm pin to fit most chains.

kit includes press plates,and all necessary riveting pieces and comes in a durable plastic case.

NOTE: when breaking a chain, YOU MUST grind the heads off of both pins on a link first.

Innovative design that cleans chain from 3 angles at once. Long handle keeps fingers and hands away from chain and sprockets.

• Will not harm O-ring chains
• Easily adjustable for all chain sizes

Make your life a little easier by having a set of these in your toolbox. Designed to simplify installation and removal of clip-type master links. One tip is shorter and notched to be placed on the pin which allows the longer end to push the clip.

This Motion Pro press tool is a must have when installing and removing Clip-Style master links (520, 525 & 530 sizes).

Easily presses on and off master link plates, works on 520, 525 & 530 Clip-Style master links.

Maximum master link width 24.8mm.

Will not damage master links, hardened steel pins for reliable use.

Light weight billet aluminum construction.

A high quality master link press tool from Wirth Machine used for the removal and installation of master links using a press fit link plate.

Fits 520, 525, and 530 pitch chain.

ULTIMATE SPROCKET WRENCH KIT

• 12” long wrench gives you more torque to get those thread locked sprocket bolts off easily
• Double ended 12mm & 13mm to fit all modern motocross, Enduro and dual sport bikes
• Dog leg wrench design allows wrench to easily clear rim edge and wide tires
• 8mm allen fits most Japanese bikes 8” long for extra leverage
• Torx T45 fits late model KTM and Husqvarna bikes, 8” long for extra leverage
• Vinyl coated handles to protect rim edge and give a non slip grip
• Makes routine sprocket bolt maintenance a quick and easy job

• Hardened metal rotor/disc locks resist cutting, sawing and chisel attacks
• Comes with carry pouch and a disc lock reminder cable
• Includes an extra mini flashlight key for three total keys
• Features a durable push button lock with high security anti-drill round key lock cores

• Sintered Pads are best for regular riding. Long life, and good performance in all conditions
• Sport Carbon pads are made for fast riding in dry conditions. Not recommended for mud, water, or sand.

Includes pads for both front and rear.

• Sintered Pads are best for regular riding. Long life, and good performance in all conditions
• Sport Carbon pads are made for fast riding in dry conditions. Not recommended for mud, water, or sand.

Includes pads for front and rear

Stainless Steel brake lines are typically the first brake upgrade you should make. Stock rubber lines will break down and expand causing a spongy brake feel or worse. Steel lines eliminate expansion which results in consistent feel and performance.

• Kits are assembled with high-quality components all designed and manufactured to meet or exceed the OEM parts
• Each kit contains all the necessary components to rebuild the brake master cylinder

This brake bleeder makes bleeding your brakes a one man job.

The unique check valve allows fluid and air to escape while preventing air from re-entering the system.

Combines wrench and bleeder valve into one convenient and compact tool

• Fits most 8 mm bleeder nipples
• Bleeds brake systems and hydraulic clutch systems
• Internal check valve for fast easy bleeding
• Anodized billet aluminum handle with chrome moly steel body
• Compact size for tight spaces
• High quality internal seal
• Multi position handle

Sized perfectly for adult back-yard racing or fast/aggressive mini riders. This is the most important upgrade you can make for an adult sized rider. The stock suspension is too soft for most adults and aggressive kids.

• 30% stiffer than stock
• Preset and stress relieved for long life
• Custom wound from aircraft grade spring steel

Fork Seals - 31 mm x 43 mm x 12.5 mm

Features:

• High quality OEM replacement seals
• Manufactured to factory specifications
• Packaged 1 pair per package

High quality fork boots. Sold in pairs.

Choose from; black, royal blue, yellow, or red.

Sized perfectly for adult back-yard racing or fast/aggressive mini riders. This is the most important upgrade you can make for an adult sized rider. The stock suspension is too soft for most adults and aggressive kids. Fits stock shock.

• 30% stiffer than stock
• Preset and stress relieved for long life
• Custom wound from aircraft quality spring steel
• Powder coated finish

Stock suspension suffers from poor compression damping and limp rebound damping. The Race Tech Gold Valve allows you to tune both compression and rebound valving for vastly improved performance.

• Bolt-on shock valving for serious suspension performance
• Improves control, traction, plushness and bottoming resistance
• Improved, long-wearing, low-friction sealing design decreases fade
• Includes complete instructions

Based on the wildly popular Race Tech Suspension Seminars taught by Paul Thede around the world, this step-by-step guide shows riders how to make their bikes handle like the pros. Thede gives the lowdown on all types of suspension, including cartridge and non-cartridge forks as well as dual-chamber and nitrogen-charged shocks.

The three forces of suspension, testing procedures, even the black arts of chassis geometry: This explains it all. The book provides step-by-step photos of suspension disassembly and assembly as well as a detailed troubleshooting guide for dirt, street and track.

• Extracts dirt and debris trapped between fork seal and tube
• Easy way to keep fork seals clean and debris free
• Works on conventional and upside-down forks

Showa removed the schrader valve on many newer rear shocks. Now you need a needle to recharge your shock with nitrogen after a rebuild. Race Tech built this unit just for that job.

The features of this tool include 300 psi capacity, bleeder valve and T-handle plunger pin chuck. Swivel chuck has a 12" flexible hose. Comes complete with instructions, carrying box and Schrader valve extension (required on some Showa shocks). Nitrogen bottles available at any welding supply house.

The Mini Powercore 4 is the best bang for your buck performance exhaust system out there.

Offered as a standard Mini Powercore 4, or as a Spark Arrestor Version, the Mini Powercore 4 features a Hi-Flo stainless steel core and formed end caps, an aircraft grade aluminum canister and a durable stainless steel header. It is pounds lighter than stock and you will swear the motor has been bored and stroked with the first twist of the throttle.

The T-6 exhaust system contains a stainless steel head pipe, brushed aluminum canister and a carbon fiber end-cap for added durability and a professional look. This exhaust system features the same benefits as the T-6 Stainless Steel Exhaust System, but is designed to fit Yamaha's TT-R125 model. In addition to all of these features, the T-6 will come with a removable United States Forest Service approved spark arrestor for trail/off-road riding.

Features Include:

• Improves performance
• Stainless steel construction throughout head pipe
• Brushed aluminum canister
• Carbon fiber end-cap
• Strong mounting bracket for increased strength and durability
• Asymmetrical muffler configuration for increased packing volume
• Removable U.S.F.S. approved spark arrestor
• Two piece system including head pipe and canister
• TIG precision welding

• Reduce exhaust sound by one to six decibels
• Options for DG V2 & RST and for the older "O" & "R" Series mufflers
• Easy installation; remove rear end cap and place Quiet Core in front of the spark arrestor
• Smaller diameter inserts are quieter but more restrictive; larger inserts are less restrictive but louder
• 1" Not recommended for RST
• Each size is sold separately

This Quiet Insert comes stock in all new FMF Q4 mufflers. If you lost yours, this is the replacement you need.

It will fit Q4, Q4 Hex, Powercore and Powercore Hex mufflers.

It will reduce the sound rating of the Power Core models, from about 99db down to about 96db.

Please choose the correct Insert for your muffler. If you are unsure of the year that your muffler was manufactured you can easily identify visually which insert you will need.

Protect your head pipe from rock damage. This stainless steel spine clamps to your head pipe to add a layer of protective armor between your vulnerable pipe and those nasty rocks or logs. Fits the stock headpipe. Will fit the FMF head pipe with the addition of larger clamps.

This universal heat shield provides a great look at a great price.

• Fits all 1-1/2" - 2-1/8" Pipes
• Measures 7-1/4" x 3"
• We recommend Anti-Seize on all exhaust fasteners.

If your aftermarket exhaust is missing heat shield mounting points, this is the easy fix you’ve been waiting for. 

Includes one stainless steel mounting bracket with M6 threaded nut, and one stainless steel hose clamp.

Fits exhaust approximately 1.1inch-2inch diameter. Trimming may be required for smaller diameter exhausts.

Have you lost your stock heat shield, or need one on an aftermarket head pipe? FMF makes this nice unit that includes clamps, heat shield with the FMF logo and button head screws to hold it on. We recommend Anti-Seize on all exhaust fasteners.

Don't get burned! Giant Loop's ingeniously simple and effective exhaust shield protects bags and bodywork from heat damage. The Hot Springs Heat Shield helps avoid the meltdown, preventing bags and side panels from touching your bike's exhaust. It's the lightweight, universal heat problem-solver for virtually any motorcycle exhaust system. Backed by a Limited Lifetime Warranty.