DR350SE

Includes forged JE 89mm piston 10.5:1 piston, Rings, Clips, Pin, big bore sleeve and top end gasket set. You will have to have the big bore sleeve installed in your cylinder and bored to fit the larger piston.

Lowers the rear suspension 2 inches. Precision machined from billet aluminum and gold anodized.

Our logo on a 20oz double wall 18/8 stainless steel thermal tumbler with copper vacuum insulation, threaded snap-fit lid, and powder coated finish.

The copper plating on the inner wall is an extra defense against temperature transfer.  Heat escapes much slower so your hot coffee stays hot even in a snow storm, and heat enters much slower so your ice water doesn't melt even under a blistering summer sun.

We have personally tested this bottle with 160° water placed on it's side for 7 hours, mimicking being in a saddle bag with coffee from the morning campsite and found that the bottle did not leak when the lid was properly secured and the water only dropped to 113° and the end of our test.

Pair it with the OBR bottle wrap for even better value and have a holder on your luggage for your new bottle for ease of access and security.

Includes forged Wiseco 83mm Piston, Rings, Clips, Pin and top end gasket set.

Includes forged JE 89mm piston 10.5:1 piston, Rings, Clips, Pin, big bore sleeve and top end gasket set. You will have to have the big bore sleeve installed in your cylinder and bored to fit the larger piston.

This is the little rubber plug on the right hand side of the cylinder head. Replace this plug to avoid having an oil leak after disassembling your top top end.

• Complete set of friction plates, steel plates, and springs
• Heavy-duty springs help prevent clutch slip
• Restores proper stack height, fixes clutch slip caused by wear and tear

• Reduce wear, and significantly increase your engine life.
• Easy to install. Place on outer side of filter.
• Powerful magnet traps abrasive metal particles down to 1 micron. OEM oil filters only filter particles down to 90 microns, leaving behind the most harmful particles to circulate through your engine.

Providing unbeatable performance and exceptional value, Hiflofiltro is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide. The filters are also supplied to original equipment manufacturers as well as private label brands.

You pay $3.40 per filter with our value 10-pack!

A 10-pack of drain plug sealing crush washers. Replace your sealing washer at every oil change to prevent a leak.

Hardened chrome vanadium steel with built in rubber insert to hold spark plug steady.

Thin wall bi-hex sockets designed to access narrow spark plug holes.

Fits 3/8" square drive and hex drive, 16mm, 18mm, 21mm.

Keep your motor running right with a fresh plug.

A Dual Electrode spark plug will last longer than a single electrode plug because the wear is shared between the electrodes.

Iridium spark plugs are made with premium quality materials.

Iridium plugs last longer than standard ones, meaning you won't have to replace them as often.

• The ultimate in the evolution of spark plug technology and performance from an industry leader
• The iridium electrode is 25% smaller than a platinum electrode, and it's just 1/4 the size of a conventional nickel electrode
• Ultra-small diameter center electrode reduces voltage requirement and extends ignition system life
• Metal shell plating has enhanced anti corrosion qualities

Sold individually, unless otherwise stated.

Clymer manuals are the most user-friendly repair manuals. They are written for the do-it-yourself-er as well as the experienced mechanic by industry experts. Step-by-step instructions based on the complete disassembly of the machine. This manual in written to cover 90-94 models but nearly all of the information will apply to newer models also.

Includes degree wheel, dial-gauge, multi-position stand, extension, 3-sizes of positive-piston stops, and a handsome wooden carrying case.

Made from medium carbon steel with hardened jaws. It features spanner pins and the jaws open up to 5" wide. It's ideal for holding clutch hubs, flywheels, gears, sprockets, etc. Made by Motion Pro.

This tool is designed to separate vertically split crank case halves on two and four stroke engines. Adjustable arms allow it to be used on multiple bolt patterns found on a variety of makes and models of motorcycles. Industrial grade steel construction with black oxide finish for long service life. Comes with 8mm mounting bolts and 6mm adapters. Protective carrying case included.

For easy removal of recessed oil filters.

Conical point screws pierces and grabs the metal end cap of the filter.

reduces potential damage to the engine cases.

NOT for use on re-usable oil filters.

A 3-pack of easy to apply strips measure the temperature of engine, suspension, and radiator components. Temperature range 146° to 248°

Thread Chasers are designed to clean and re-cut damaged aluminum threads.

this kit contains the two sizes most common on metric motorcycles, M6x1.0 and M8x1.25.

Thread Chasers also remove dirt and metal shavings that become captured in thread grooves.

Uses 8mm or 10mm hex sockets, a Must for all tool kits.

A 'wrench style' tool to turn the 'square top' tappet screws. The wrench does a better job of holding the adjuster screw still while tightening the locknut. Slim and flat, this tool is easy to carry in a tool pack.
 

• Heat treated and chrome plated for durability
• Include 10mm wrench with 3mm square adjuster
• Fit motorcycles and ATVs with screw-type adjusters

Included Items:
(1) 10mm chrome steel socket wrench
(1) 3mm square tappet adjuster

Dual marked feeler gauges. 32 blades  from .03mm/.001" to 1mm/.040"

Designed for use with stock engines using either stock or aftermarket exhaust and air filters.

• Provides a simple and affordable solution to carburetor tuning problems
• Allows you to tune your bike for increased power and smoothness while retaining fuel economy
• Includes a guide booklet on how to install and use your jet kit to it's full potential

Each kit contains float bowl gasket (or o-ring), float valve assembly (or float needle) and o-rings to rebuild one OEM carburetor body.

The Remote Fuel Mixture Screw is 5 inches longer than stock. This gives you plenty of length to easily mount in a convenient location. Will work with the stock BST Carburetor as well as the TM40 pumper Carburetor.

• Increased air flow over the stock air filter
• Designed to increase horsepower and throttle response
• Designed to fit inside the factory air box
• Larger surface area over foam filters which offers longer service intervals in dusty conditions
• Four layers of premium cotton gauze provides outstanding filtration
• Washable & re-usable, never wears out
• One filter will last the lifetime of your bike

DR350/DR250 all

Twin Air Filter's patented design, high quality materials and superior construction deliver unbeatable performance and protection - and make Twin Air Filters the hands-down choice of more World and National Champions than all other filters combined.
An air filter is your engine's only protection against the elements, and your stock filter isn't up to the task. Replace it with a Twin Air- the number 1 filter system proven on motocross tracks around the world.
Twin Air's fused layers of open-pore foam and fine inner foam trap even the smallest particles-without restricting airflow

Sold in 6 packs

• Compatible with many air filter boxes.
• More air flow allows you to add more fuel to your intake mixture, increasing performance.
• 1" Diameter

This canister by Pro Circuit allows you to move the overflow tubes from the carburetor up and out of the way. Universal application.

Quick release one-piece clamps that saves space. These are great for fuel lines, controlling wires, and can be used many times.

Comes with 4 each of 8mm, 9mm 10mm, and 12mm.

No special tools needed, from Helix Racing.

Increases fuel capacity for longer range than stock. All necessary hardware is included.

 Fits DR350S and DR350SE Dual Sport models. Available in white only.

• High-density polyethylene gas tanks offer maximum fuel-carrying capacity
• 3.5 Gallon Capacity
• All necessary hardware included (tank decals not included)
• Available in White Only

Become more visible and look cool while doing it. The ProCycle Natural Tank LED Light Kit will add more light to your bike with the push of a button.

Kit includes a handle bar mounted lighted switch, two 12" LED light strips with adhesive backing, four saddle splice connectors, and a center harness for connecting to your bikes harness.

Installation is quick and easy.

*Please note All colors other than amber and white are recommended for off road use only*

If you're like us, you hate the long floppy vent hose hanging off the cap of your aftermarket tank. This one-way vent cap replaces the long hose with a short one only about 2" long. It allows air into your tank but prevents fuel from sloshing out. Machined from billet alloy and anodized for good looks.

  Not for stock fuel tanks!

If you need a replacement cap for your Acerbis tank, why not go bling? These caps have a carbon fiber pattern molded into them that is extremely realistic. Looks like the real thing. Topping off the cap is a CNC Machined metal vent cap. This eliminates the need for a lengthy vent tube that gets in the way. The vent cap allows air to vent into the tank but does not allow fuel to splash out during normal use or during a tip over.

These caps fit Acerbis tanks only.

Security for your fuel tank. Includes 2 keys. Internally vented with a check valve that prevents spillage in case of a tip over.

Fits Acerbis, IMS and safari tanks only.

The small size and right angle hose barbs make this filter easier to fit into the small space between your fuel petcock and carburetor. Filter body is only 7/8" diameter. Straight filter is 2" long, 90 degree filter is only 1-5/8" long.

This filter is meant for 5/16" fuel lines. Only 1/2" thick it is small enough to fit just about anywhere.

Fuel supplies can be sketchy at times. This filter lives in your tank to trap dirt and debris as it is poured into the tank. Features a custom shaped adapter that fits securely under the gas cap, creating a leak-proof seal. If it stays out of your fuel, it can't get into the carburetor! Created by the filter experts at Twin Air, this filter fits IMS,  Acerbis and Safari brand gas tanks.

Ordering new fuel line? How about a set of fresh zinc plated clamps to go with it?

These will be sure your fuel line stays connected. A pack of 8 clamps in 2 sizes to fit most 1/4 or 5/16 fuel hose.

Hose reducer to go from 5/16" line down to 1/4" line. Many bikes have 5/16" carburetor spigots but most aftermarket petcocks are 1/4". This solve the problem of mismatched sizes. Solid brass construction. Can be used to route or repair fuel lines, oil lines or air lines. Barbed ends provide a secure fit.

30" lengths. Sizes shown are ID. All of these lines are stronger and more durable than vinyl fuel lines and are resistant to swelling, UV light, as well as hardening and cracking.

Need to mount two containers? A water and a fuel? Two waters? Already have a RotoPax Mount for a single container? Get this extender to work in conjunction with a pack mount and that will be no problem! Single mount, two containers.

RotoPax holder made to mount a single Fuel and/or Water container.

Need to mount two containers? A water and a fuel? Two waters? Get the extender which allows you to stack two containers no problem! Single mount, two containers

RotoPax are Rotational Molded - the process which produces indisputably superior products.

• Thicker walls and stronger construction
• Bright colors that are less prone to fading
• Extra threads, thicker walls, and sure-seal gasket guarantee no leaks

Need to mount two containers? A water and a fuel? Two waters? Finally, you can stack multiple packs together! Use in conjunction with a pack mount. You will need to purchase the Single Mount as well as the Extender.

Giant Loop's Gas Bag Fuel Safe Bladder conveniently transports 1 gallon of hydrocarbon fuel for power sports use in a collapsible welded film and ballistic nylon reinforced container that rolls up or packs flat when empty, weighing less than 1 pound.

The Gas Bag Fuel Safe Bladder Kit includes 2 pairs of Giant Loop's adventure proof 26" Pronghorn Straps plus a 3-Pack of Fast Funnel Disposable Fuel Funnels.

Each Gas Bag Fuel Safe Bladder is individually pressure tested and made in USA by Fuel Safe, a leading fuel containment manufacturer based in Oregon.

• Volume: 1 gallon maximum capacity (3.8 liters).
• Empty weight: 11.5 oz.
• Dimensions (flat and unfilled): 19.5" long x 9.5" wide. Rolled diameter (empty): approximately 4".
• Filler neck is standard size, fitting "universal" spouts.
• Materials & Construction: Welded film bladder sewn into ballistic nylon sleeve with webbing daisy chain anchor points and handles.

Auxiliary fuel tanks mount to handlebars, forks, or rear racks.

• Suitable for minis, trials bikes, full size bikes, and anywhere else a little extra fuel is needed.
• Each tank includes a siphon kit that connects the tank to the main fuel tank and automatically siphons fuel while the bike is being ridden.
• With this design, the auxiliary tank empties first, before the main tank.
• Does not interfere with headlight, handguards, rear seat, etc.

This Super Siphon has  a (1/2 inch x 6 foot) long hose, which makes it quite easy to transfer fuel from one bike to another! Simply, shake the hose to prime it and get fuel moving.  The hose is resistant to gasoline and any other hazardous chemicals. Roll it up, stuff it in your bag and you will be very happy whenever you need it.

Windscreen attaches to your bike's handlebars. Fully adjustable mounting brackets. Includes 7/8' handlebar clamps.  14" tall & 10" wide.

  Will not fit 1 1/8" oversize handlebars.

Puig Visor Clip-On

• Suitable for screens with thickness between 3-5mm
• Multi-adjustable visor adaptable to Puig and OEM windscreens
• Visor is mounted by clip-ons and does not need to be drilled to the windscreen
• Visor sizes available include 90x230mm, 100x277mm and 102x325mm

Front fender from DSA Concepts Plastics is shaped very much like the OEM DRZ400SM front fender. Big enough to be functional without wind-steering the bike like the stock fender does.   Vacuum molded, these are a design improvement over stock.  These are fully compatible in any combination with the original factory plastic. 

Universal design.  Vents in the back improve airflow to motor.  Smaller front reduces 'wind steer' and improves high speed stability.

Genuine Suzuki super moto fender. A perfect match for the original gray plastic.

Universal off-road front fender. Must be drilled to fit your mounting bolt pattern.

Replacement screen for Adventure-Spec Mini Fairing.

This is for screen only, please see Mini Fairing Support for complete assembly.

 In stock with limited availability in WHITE only, due to manufacturer supply delays.

This frame includes six, white, full-spectrum LED bulbs on a 6-inch strip for bright illumination of your license plate. It is made in a sturdy cast aluminum, and is powder coated with a durable black finish.

Outside frame dimensions are 7.25" in. wide by 4.2". Center to center mounting hole distance is 5.7 in. All mounting hardware is included.

Adhesive heat shield for your new side panel plastics to protect it from the heat of your muffler.

Corbin seats are custom made to order. You can choose your preferred texture for the top and sides of the seat. Please give us a call if you would like other color options or materials.

Corbin seats are custom made and carefully designed to provide a comfortable riding position. They are firm and supportive which allows you to ride all day without fatigue unlike the stock seat.

Because Corbin seats are custom made to order, Please allow about 2 weeks lead time to have the seat built.

The default vinyl choices are black 'carbon fiber' on top and 'asphalt' on the sides.  You can view all of the available materials and colors on Corbin's Website.

  Corbin seats are custom made to order. Allow 3 weeks delivery time.

Seat Concepts dual-sport/adventure seat-kits incorporate a wider seating area for the rider, which results in more even weight distribution, while reducing pressure points. Each individual seat model has been specially designed to increase comfort without compromising ride-ability. The more aggressive the bike, the more aggressive the seat-kit.

Each kit contains detailed instructions for easy "Do It Yourself" installation. This provides the highest level of quality & comfort at an affordable price.

This is the secret for being able to put in those 500 mile days. Even a good touring seat can feel a bit firm after a couple hundred miles. Sheepskin gives that little bit of 'cush' and provides superior air circulation. Velcro straps allow easy removal when you don't need it. Measures 14" wide by 19" long.

• Air filled AirHawk 12"x18" cushion custom fits your shape and redistributes pressure that causes numbness and discomfort when you ride
• Seat cushion cover is constructed of a breathable, stretchable Nylon/Lycra blend with a non skid Urethane base
• Open mesh side panels allow heat to escape
• Easily inflates by mouth with no pump needed
• Mounting straps and Repair patch kit included

9" by 9" carbon fiber seat warmer that goes between your seat cover and the foam to keep your backside happy on those really cold days. This improved design produces 25% more heat than most other warmers using just 30 watts.

Kit includes the warming unit, with connector, 24" extension cable, rocker-type on/off switch and stub to splice into your wiring along with complete detailed instructions.

• Made from strong and lightweight aircraft aluminum
• Protects vital engine parts from rocks and debris
• Custom fit to your specific bike model
• Oil drain hole for easy access
• All mounting hardware included

Protect that vulnerable rear master cylinder with this thick aluminum guard from JNS Engineering. CNC laser cut then formed and given a clean black powder coat finish. Includes new button head screws and aluminum spacers.

Contoured alloy hand guards with inner mounts, allow space for the clutch cable and brake hose.

Images show a set of these hand guards installed on a set of CR High Gunmetal Fly Handlebars with large black deflectors. The far right image shows the need to flip the brackets that attach to the bar on the clutch and front brake side. On the front brake side the clamp must go over the front brake line while on the clutch side it goes under the cable.

These handguards come with mounts that will work on both standard and and oversize bars. The aluminum wrap-around bar is the biggest on the market with two large plastic shields that are also some of the largest available. The X-Factor hand guards offer great protection from the elements, especially during those colder months when you're trying to stretch out your riding season.

Works with 7/8" or 1-1/8" bars.

  X-Factor guards require you to cut your lever ends down, or use short levers.

Replacement handguards for your Acerbis set up. Tough Polypropylene shields with a larger 6" outer diameter, built for extreme riding conditions.

The X-Factory Handguards from Acerbis feature a steel bar wrapped with an injection molded Nylon composite. A replaceable dual injected polypropylene shield mounts to the bar offering insurmountable protection from roost, debris, and extreme conditions.

A universal mount kit is included that allows for mounting on either 7/8" or 1 1/8" handlebars.

• Designed to minimize handlebar vibration for Barkbuster Handguards that can’t accomodate OEM handlebar weights.
• Sleek aerodynamic look.
• Forged Steel with powder coat finish.
• Fit in conjunction with most Barkbusters backbones (except EGO).
• Fits externally to the VPS backbone.
• Available in black.
• Sold as a pair

Weight:
360 grams/pair or
180 grams/each

Extend your comfortable riding season with Barkbusters BBZ cold weather protection handguards. Designed to fit with or without existing Barkbusters backbones or handlebar weights, these guards offer superb wind protection without limiting access to your grips or controls. Simple to install, they can be mounted or removed within ten minutes without permanent modifications. Ride with less bulky gloves in colder weather with the Barkbusters BBZ cold weather protection handguards.

Features:

• Fits most motorcycle handlebars
• Maximum cold weather protection
• Compatable with or without Barkbusters backbones
• Lined with waterproof membrane
• Windproof
• Full wrap design
• Allows full access of controls
• Does not block view of handlebar thumb controls
• Simple to install and remove

Whats in the box:

• Two BBZ cold weather handguards
• Mounting hardware
• Instructions

Protect your hands and levers with the Barkbusters Storm lever and weather protection handguards. Full wrap solid heat treated aluminum bars with secure two point mounts on each side provide strength while attractive and generous guards provide shelter from the wind and weather. Ride longer with the Storm handguards and complete mounting kit by Barkbusters.

Features:

• Two mounting points provide secure protection
• Full wrap guards
• Heat treated aluminum backbone bars
• Easy installation
• Tough and weather shielding Storm handguards
• Aluminum backbones are compatible with all Barkbusters deflector guards

What's in the box:

• Left and right aluminum backbone bars
• Inner and outer handlebar mounting hardware for both sides
• Left and right Storm plastic handguard deflectors
• Installation instructions

  Not recommended for Africa Twin, T7, Himalayan, or V-Strom.  Please see specific listings for those models.

NOTE: tapered kit will not fit Renthal Twin Wall or Barkbusters VSBar

Maximize your wind protection with the Barkbusters largest handguard plastic! For use with single sided Storm mount and all Barkbusters backbone handguards

Keep your hands and controls protected from the wind and impact with Barkbusters VPS lever and wind protection handguards. Heat treated aluminum backbones with two mounting points of these handguards provide the strength needed to prevent a tip-over from ending your motorcycle ride. Impact resistant deflectors, available in multiple colors, provide protection for your hands from the wind and brush. Ride longer, more comfortably with Barkbusters VPS lever and wind protection handguards

Features:

• Two mounting points provide secure protection
• Full wrap guards
• Heat treated aluminum backbone bars
• Includes VPS left and right plastic deflectors
• Easy installation

What's in the box:

• Left and right aluminum backbone bars
• Inner and outer handlebar mounting hardware for both sides
• Left and right VPS plastic deflectors
• VPS deflector fastening hardware
• Left and right adjustable position wind extension deflectors
• Installation instructions

 Not recommended for Africa Twin, T7, Himalayan, or V-Strom.  Please see specific listings for those models.

NOTE: tapered kit will not fit Renthal Twin Wall or Barkbusters VSBar

Replace the deflectors on your aluminum bar backbones with Barkbusters VPS wind protection replacement handguards.

Construction of these handguards feature heavy duty aluminum guards with colored plastic deflector shields. They offer great protection from those trees that jump out at you on the trail and the cold wind and rain you encounter on the street. They feature a deep bend on the outer bar end for maximum freedom of hand placement and high quality bar mounts on the inside.

Select your desired color with the corresponding size mounts to fit your handlebar.

Replacement handguards for your Cycra set up. Injection-molded high-impact plastic replacements. Includes all hardware needed for mounting.

Fits Moose and other aluminum hand guards

• Aerodynamic and stylish design
• Protect hands from brush, water and cold wind
• Simple installation
• Sold in pairs

The OBR ADV Gear Enduro ¾ Grip Mitt is your answer to cold fingers! Our ¾ open design terminates right at the wrist, but still offers full coverage of the hand while blocking the swirling air flow that freezes finger tips. Their ¾ open design does not cover important controls such as Hi/Lo Beam, Turn Indicator, or Kill Switches making this Grip Mitt perfect for both Off Road, Enduro, ADV, and ATV applications with full wrap hand guards.

Features

• High strength and water resistant 1680d Ballistic Nylon construction 
• Universal easy on/off Velcro snap strap attachment system
• Reflective Front Strip for High Visibility
• ¾ Open design provides full coverage of the hand while not impeding controls
• Works with OEM and Full Shield (Cycra/Trackside) style hand guards (Hand guard system required for attachment)

Extra protection in bad weather to help keep your hands warm and dry. These nearly double the protection from most plastic type deflectors.

The outer shell is made from heavy-duty 500-denier nylon with 1/2" closed cell foam to keep the wind, cold and rain off of your hands.

FUZION guard feature the ultimate in hand protection with a unique design and flexible yet durable material. The expanded coverage area sweeps back toward your hand significantly increasing coverage making it perfect for cold, muddy or wet conditions. The FUZION features a unique two position mount and is constructed of molded light-weight closed-cell AEPE foam, which is crush-proof, water proof and extremely durable. The FUZION will work great for road of offroad riding, where wind deflection is important, and or bouncing off trees is a common occurrence. Kit includes mounts. Optional replacement mounts available.

Black in color

Upgrade your bike with FLY Aero 1-1/8" bar. Constructed of Aircraft grade 7075 taper walled aluminum that tapers to a standard 7/8" to accept stock controls.

• Bead blasted surface for added strength
• Laser accurate steering
• Dissipates shock and reduces rider fatigue

ProTaper's ADV handlebars give you a bar taller than most with extra space on the control portion of the bar. These bars provide an additional 20mm of space next to where your levers and throttle are located for your GPS, phone cradle, auxiliary switches, etc . They come in Adventure (which is taller than stock) and Adventure High (which is even taller).

These  are oversize bars, which means they are are 1 1/8", not the smaller 7/8" diameter. Therefore some bikes will require a adapter and there are several available to select from.

Comfortable Oversize (or Fat Bar) Handlebars. For bikes with standard 7/8" handlebars these will require the use of a 7/8 to 1-1/8  adapter. Black in color. Raise your bars and get rid of the crossbar that obstructs your view of the speedo. Works with stock controls and cables.

These 7/8" bars fit in the stock clamps and raise your grips a couple inches. They look great too!

These 7/8" Silver bars fit in the stock clamps.

• Width 815mm
• Height 113mm
• Rise 84mm
• Clamp Area 173mm
• Sweep 49mm
• Control Area 206mm

• 4.75" wide,
• Requires 7/8" bar clamps on bike
• Raises handlebars 2 inches and allows fore/aft position adjustment
• Provides dual pivot points for optimal bar positioning
• One piece design is made from solid aluminum for superior strength
• Available for 7/8" - 7/8" or 7/8" - 1 1/8" bars

These versatile Risers allow you to clamp a 7/8" diameter handlebar or you can remove the 7/8" reducers and then clamp an 1- 1/8" aluminum "fatbar". If you are thinking of going to a fatbar after you bend your stock set or just want the versatility and option to run any bar, this is the riser to go with. Reducers lock into risers to insure no slippage between components. Anti-Vibe Risers may interfere with aftermarket large capacity fuel tanks, and some steering stem clamp configurations (use standard pivoting risers). These risers use 8mm bolts. Always check and confirm that your bike has adequate cable and brake line length before installing any handlebar risers.

This unique design from Rox allows you to move your bars either closer (1" up and back) or further away (1" forward and 1-1/4" up) depending on rider preference. These risers have an oblong mounting hole so that they will fit virtually any triple clamp with 8mm bolts. A set of reducers lock into the risers ensuring no slippage whether you have a 7/8" or 1-1/8" bars

Features:

• BluPulse™ Technology combines intelligent micro electronics with thermal sensors in each grip allowing the rider to select between six temperature settings
• Ergonomic Design, reduces wrist and hand stress
• Universal Throttle System designed to fit the vast majority of Sport and Dual Sport bikes
• Intelligent power shut off system, prevents accidental battery power loss
• Made of a specially formulated Valcathane™ material that produces a soft but durable surface
• Glue-less design features molded grip on throttle slide and left hand Clamp-on grip

Highly efficient design delivers warmth faster than traditional heated grips.

Choose from the standard five level push button temperature controller, or the LCD display controller which shows the selected heat level and available battery voltage.

The Apollo Heated Grips are designed with an integrated adjustable thumb switch, which allows them to easily fit on any kind of motorcycles on the market. The integrated thumb switch gives control to the rider to adjust the temperature level while keeping hands on the bar for a safer ride.

Its wide temperature setting range will keep the rider comfortable under the cold riding conditions.

The 5 color LED display will enhance the visual look of the heated grips and will allow the rider to quickly know at which heat level the grips are set.

This system will also detect if the battery voltage is too low and will automatically shut down the heated grips in order to make sure the rider have enough power to start the engine or use the motorcycle.

Specifications:

• Integrated thumb switch designed for easy installation and control.
• “Plug & Play” wiring connections to shorten the installation time.
• Wide temperature settings for various weather conditions.
• Low Battery Warning protection to ensure the motorcycle has enough power to start.
• 5 color LED Indicators for the rider to quickly know in which heat level the grips are set.

• Ergonomically designed
• Medium-density Thermoplastic Rubber (TPR) compound provides excellent feedback and control, without sacrificing durability
• Full diamond pattern for an unparalleled feel in both wet and dry conditions
• Inner diameter optimized to keep grips secure in any conditions
• 115mm overall length; fit 7/8" bars and throttle sleeves

These grips feature a thicker design that dampens vibration. The soft shoulder allows ease of movement. Three wire-tie grooves are molded into the grip to make securing them a breeze. We think they are great!

Reduces vibration and cushions impact. Inner core compound perfects the bonding interface with bars. Anti-Rip Tip™ uses denser compound to increase life of grip. Designed to self-clean and shed mud away from outer surface. Tacky gel-like surface compound is perfect for offroad and MX.

Temporarily out of stock, current available ETA end of May 2021.  Ordering now will reserve yours.

Each pattern is available in three advanced synthetic rubber compounds. This means you can have the optimum combination of strength, tackiness and shock absorption to suit every riding condition and individual style. Soft grip is extremely soft, giving you a very comfortable ride, great feel and reduces the chance of blisters; however, because the grip is so soft, it wears quickly. Medium is a compromise between firm and soft. Firm grip has the same feel as a stock grip, it is very strong and has very good resistance to tearing and abrasion. Half Waffle has waffle pattern in finger area for traction and diamond pattern on palm side to reduce blisters. Full Waffle: designed after the CR Honda® grip.

• Feature the classic Vans waffle sole pattern with a subtle domed center section for improved ergonomics and vibration dampening
• 125mm in length
• Fit 7/8" bars
• Sold in pairs

This little jewel reduces hand fatigue and cramping on long rides or daily commutes. The Crampbuster is not a throttle locking unit but, rather a simple clip-on device which allows you to relax your grip while riding.

The Go Cruise cruise control mounts over the throttle grip and rests on the brake lever to hold your throttle open, allowing you to stretch and rest your hand on long rides. Installs and removes in seconds with no tools. You can roll off the throttle manually to disengage the Go Cruise.

Ease the pressure on your wrist during those long highway drones out to where the fun begins. ProCycle has developed this kit that includes a Vista-Cruise throttle lock, a specially modified alloy throttle tube and an anchor plate that attaches to your throttle housing. Just flip the thumb lever down to apply enough friction to hold the throttle in place. Use the supplied longer screw to attach the anchor plate to your lower throttle housing bolt hole. Also included is a tension adjustment tool that you can keep on your key ring. Keep the applied tension lightly adjusted so it's easy to roll the throttle off.

  Fits bikes with dual cable throttle housings.