2017 - 2020 Year range.
The CRF250 Rally is a lightweight adventure bike offered from Honda. The Honda CRF250 Rally is powered by a liquid cooled single cylinder 249cc four stroke engine mated to a 6-speed transmission. The CRF250 Rally weighs 346lbs and has a ground clearance of 10.6 inches with a seat height of 35.2 inches. The fuel tank has a capacity of 2.64 gallons.
| Chain Size: | Front Sprocket: | Rear Sprocket: | Front Tire: | Rear Tire: | Spark Plug: |
|---|---|---|---|---|---|
520x106 | 14T | 40T | 3.00-21 | 120/80-18 | SIMR8A9 |
Higher pressure in the cooling system, raises the coolant boiling point and increases protection from coolant loss due to overheating.
23 PSI - 1.6 Bar.
Genuine Honda replacement thermostat
Our kit includes 5 EBC friction plates which eliminates the judder spring assembly by replacing it with a 5th friction plate.
Heavy duty clutch springs by Barnett are included it this kit which will significantly decrease wear under high stress conditions.
Includes genuine Honda friction plates, drive plates, and clutch springs.
Barnett clutch springs are made from the finest materials available.
Heavy Duty Barnett clutch springs are pre-set, shot-peened, and heat treated for performance and durability.
High quality stator cover gasket.
Includes all necessary top quality gaskets for top end rebuilds.
Genuine Honda replacement oil filter cover gasket.
Providing unbeatable performance and exceptional value, Hi-Flo is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide.
Grab our 5-pack and save both time and money!
Extra protection for your motor! Strong magnet at the end of the plug picks up metallic flakes in your oil, protecting your engine!
GoldPlug is the gold standard in engine protection.
Stainless steel drain plug with an extremely strong magnet that picks up metal flakes in your oil.
12mm Thread, 17mm Head.
A 10-pack of drain plug sealing crush washers. Replace your sealing washer at every oil change to prevent a leak.
Hardened chrome vanadium steel with built in rubber insert to hold spark plug steady.
Thin wall bi-hex sockets designed to access narrow spark plug holes.
Iridium spark plugs are made with premium quality materials.
Iridium plugs last longer than standard ones, meaning you won't have to replace them as often.
Sold individually, unless otherwise stated.
Laser Iridium
With the smallest tip diameter available, OE Iridium spark plugs provide superior ignitability and long service life. The iridium/platinum surfaces ensure a slow wear rate, providing stable idle and superior anti-fouling.
Genuine Honda Factory Service Manual specifically for your CRF250L
Made from medium carbon steel with hardened jaws. It features spanner pins and the jaws open up to 5" wide. It's ideal for holding clutch hubs, flywheels, gears, sprockets, etc. Made by Motion Pro.
This tool is designed to separate vertically split crank case halves on two and four stroke engines. Adjustable arms allow it to be used on multiple bolt patterns found on a variety of makes and models of motorcycles. Industrial grade steel construction with black oxide finish for long service life. Comes with 8mm mounting bolts and 6mm adapters. Protective carrying case included.
Includes all necessary top quality gaskets, and seals for engine rebuilds.
For easy removal of recessed oil filters.
Conical point screws pierces and grabs the metal end cap of the filter.
reduces potential damage to the engine cases.
NOT for use on re-usable oil filters.
A 3-pack of easy to apply strips measure the temperature of engine, suspension, and radiator components. Temperature range 149° to 248°
Thread Chasers are designed to clean and re-cut damaged aluminum threads.
This kit contains the two sizes most common on metric motorcycles, M6x1.0 and M8x1.25.
Thread Chasers also remove dirt and metal shavings that become captured in thread grooves.
Uses 8mm or 10mm hex sockets, a Must for all tool kits.
32-Blade Dual-Reading Tapered Combination Feeler Gauge Set
Tried, true and tested the Power Commander continues to evolve with the Power Commander 6. Developed to simplify the user experience, PC6 makes choosing and tuning a map easier for the end user. All the same benefits you have relied on for over 20 years remain to keep you at the front of the pack.
The Power Commander 6 fuel injection tuning device allows you to optimize your fuel and timing curve (where applicable) giving you the confidence to roam freely. With fine tune adjustability and multiple inputs, the Power Commander 6 will keep your vehicle running at its full potential letting you concentrate on the journey ahead.
Featuring a plug-and-play setup, Power Commander 6 can be installed discreetly underneath your seat, cowl, dash or other location ensuring your ride looks as good as it runs. Removing the device reverts your vehicle completely back to stock. With the ability to store and switch between two maps on-the-fly (via the map switch accessory) and connect to various Power Commander accessories such as the Autotune, Quickshifter or POD-300, the Power Commander 6 gives you features and functions that provide you with the ultimate ride.
All PC6 models have an end-user adjustment of +/-15 in the FUEL table and +/- 8 in the timing table (if applicable). This adjustment is on top of the values that are in the BASE map loaded to the device. This BASE map can be any of the available maps from the Dynojet website, or those you may have received from a third party.
The EJK evolved out of the need to address the ever-increasing complexity of factory fuel injection. For the newcomer to the market or professionals wanting an easier method for tuning fuel injection, the EJK is a customizable solution for the rider that wants to take control of their tuning needs.
This unit is a piggy-back EFI controller because it does not replace the stock ECU, but rather monitors the signals to the injectors and makes fuel adjustments based on the mode settings. The GEN 3 has a push button interface allowing access up to 6 different modes to allow for quick fine tuning by the end user without needing a computer.
Key Features:
Genuine Keihin spring, washer, and oring for the fuel screw of FCR and FCR MX carbs.
Just the parts…
Fuel screw spring, washer, o-ring (fuel screw not included)
The small size and right angle hose barbs make this filter easier to fit into the small space between your fuel petcock and carburetor. Filter body is only 7/8" diameter. Straight filter is 2" long, 90 degree filter is only 1-5/8" long.
This filter is meant for 5/16" fuel lines. Only 1/2" thick it is small enough to fit just about anywhere.
Genuine Honda replacement air filter.
Sold in 6 packs
Not legal for use on pollution controlled vehicles in the state of California.
TechSpec’s Motorcycle Tank Grips were developed to improve body, bike control and increase riders comfort. Gripping your motorcycle between your knees or thighs improves overall control of your ride by better securing your body weight and seat position under the forces of braking, cornering and acceleration while also relieving pressure from your wrists, elbows, shoulders and lower back giving you increased control and a more comfortable, safer ride. Snake Skin is a thin, .125” medium durometer “rubber” material that offers a secure, comfortable grip, durable protection and a clean stock look.
This universal precut kit includes left and right tank grips. (8" X 3") Triangle
Security for your fuel tank. Includes 2 keys. Internally vented with a check valve that prevents spillage in case of a tip over.
Fits Acerbis, IMS and Safari tanks only.
If you're like us, you hate the long floppy vent hose hanging off the cap of your aftermarket tank.
This one-way vent cap replaces the long hose with a short one only about 2" long. It allows air into your tank but prevents fuel from sloshing out.
Machined from billet alloy and anodized for good looks.
Not for stock fuel tanks!
You’d be amazed at the dirt and debris that can work its way into your gas can – and from there, your fuel tank. Twin Air’s monofilament screen pocket inserts in your tank to catch particles as small as 40 microns (.00165”) while allowing the gas to flow freely.
The flange is custom-sized for each modern 4-stroke model to ensure a leak-proof seal. Just remove the filter periodically, turn it inside-out, and clean out the debris that could have been in your engine.
Will not work with factory locking gas caps.
Inside tank inlet diameter must be approximately 43.5mm (1.71") to fit.
All of these lines are stronger and more durable than vinyl fuel lines and are resistant to swelling, UV light, as well as hardening and cracking.
Five-layer Greenshield® Barrier Technology cuts vapor loss and saves fuel, making it safe for the environment and fuel efficient.
1. Barrier tube - provides high heat and corrosive liquid resistance.
2. Greenshield® barrier - patent-pending technology provides the lowest permeation in the industry.
3. Adhesion layer - secondary protective barrier.
4. Reinforcement layer - spiral textile reinforcement provide strength and pressure resistance.
5. Cover - protect underlying components.
All of these lines are stronger and more durable than vinyl fuel lines and are resistant to swelling, UV light, as well as hardening and cracking.
Five-layer Greenshield® Barrier Technology cuts vapor loss and saves fuel, making it safe for the environment and fuel efficient.
1. Barrier tube - provides high heat and corrosive liquid resistance.
2. Greenshield® barrier - patent-pending technology provides the lowest permeation in the industry.
3. Adhesion layer - secondary protective barrier.
4. Reinforcement layer - spiral textile reinforcement provide strength and pressure resistance.
5. Cover - protect underlying components.
Ordering new fuel line? How about a set of fresh zinc plated clamps to go with it?
These will be sure your fuel line stays connected. A pack of 8 clamps in 2 sizes to fit most 1/4 or 5/16 fuel hose.
Hose reducer to go from 5/16" line down to 1/4" line. Many bikes have 5/16" carburetor spigots but most aftermarket petcocks are 1/4". This solve the problem of mismatched sizes. Solid brass construction. Can be used to route or repair fuel lines, oil lines or air lines. Barbed ends provide a secure fit.
Need to mount two containers? A water and a fuel? Two waters? Already have a RotoPax Mount for a single container? Get this extender to work in conjunction with a pack mount and that will be no problem! Single mount, two containers.
RotoPax holder made to mount a single Fuel and/or Water container.
Need to mount two containers? A water and a fuel? Two waters? Get the extender which allows you to stack two containers no problem! Single mount, two containers
RotoPax holder made to mount a single Fuel and/or Water container.
This unique design adds strength and provides extra tightening power.
Use with included base plate or remove plate to attach mount direct by bolting up through the bottom or down through the top.
RotoPax are Rotational Molded - the process which produces indisputably superior products.
Need to mount two containers? A water and a fuel? Two waters? Finally, you can stack multiple packs together! Use in conjunction with a pack mount. You will need to purchase the Single Mount as well as the Extender.
Auxiliary fuel tanks mount to handlebars, forks, or rear racks.
Quick release one-piece clamps that saves space. These are great for fuel lines, controlling wires, and can be used many times.
Comes with 4 each of 8mm, 9mm 10mm, and 12mm.
No special tools needed, from Helix Racing.
This Super Siphon has a (1/2 inch x 6 foot) long hose, which makes it quite easy to transfer fuel from one bike to another! Simply, shake the hose to prime it and get fuel moving. The hose is resistant to gasoline and any other hazardous chemicals. Roll it up, stuff it in your bag and you will be very happy whenever you need it.
Aero Tapered Aluminum (ATA) Oversize (or Fat Bar) Handlebar.
For bikes with factory 7/8" handlebars these will require the use of a 7/8 to 1-1/8 adapter (sold separate).
Comfortable Oversize (or Fat Bar) Handlebars.
For bikes with factory 7/8" handlebars these will require the use of a 7/8 to 1-1/8 adapter (sold separate).
Say goodbye to the frustration of fidgety handguard expansion plugs with Warp 9's innovative Tapped Handlebars.
These handlebars feature ends that are plugged and tapped with an M8x1.25 threaded insert, providing a secure and reliable mounting point for all aftermarket wrap-around handguards.
No more worrying about plugs pulling out or spinning during crashes; their robust design ensures you're good to go, even when you encounter obstacles.
Not using handguards? No problem they've got you covered!Each set of handlebars comes with aluminum grip guards and stainless bolts, offering protection for your grips and delicate throttle tube in case of a get-off.
Designed with an oversized 1-1/8 inch (28.6mm) clamping diameter that tapers down to 7/8 inch (22.2mm) to accommodate standard controls. Crafted from 7010 T6 aluminum tubing and featuring computer-extruded variable wall thickness, they effectively reduce vibration while enhancing overall performance and comfort.
Note: Does not include pictured bar mounts.
| Width | Height | Rise |
| 790mm | 101mm | 71mm |
| Clamp Area | Sweep | Bend |
| 142mm | 73mm | CR High |
Mika Metals Hybrid Series handlebars are truly a marvel of engineering. It is the first oversize handlebar in the world that fits on 7/8" clamps.
The patent pending design is the most unique idea to shake up the handlebar industry in quite some time. They retain all the flex properties of the pro series handlebars and allow you to run oversize bars without the oversize clamps.
Constructed from the highest quality aerospace 7075 aluminum for maximum strength. CR High Bend, includes injection molded bar pad.
Bars only fit 7/8" clamps
ProTaper's ADV handlebars give you a bar taller than most with extra space on the control portion of the bar. These bars provide an additional 20mm of space next to where your levers and throttle are located for your GPS, phone cradle, auxiliary switches, etc . They come in Adventure (which is taller than stock) and Adventure High (which is even taller).
These are oversize bars, which means they are are 1 1/8", not the smaller 7/8" diameter. Therefore some bikes will require a adapter and there are several available to select from.
Using the same manufacturing techniques and materials as ProTaper’s industry-changing 1⅛" motocross handlebar, the EVO Adventure is specifically designed to provide adventure/touring riders with the increased comfort and control they need. With over 8" of straight section in the control areas, mounting vital components is made easier than ever. With its premium 7000 series aluminum alloy construction and computer-profiled four millimeter-thick wall design, the EVO Adventure Handlebar is up to 25% lighter and 45% stronger than competing handlebars.
These 7/8" bars fit in the stock clamps and raise your grips a couple inches. They look great too!
| Width | Height | Rise |
| 813mm | 160mm | 104mm |
| Clamp Area | Sweep | Control Area |
| 236mm | 100mm | 199mm |
Requires 7/8" factory bar clamps on bike
These versatile Risers allow you to clamp a 7/8" diameter handlebar or you can remove the 7/8" reducers and then clamp an 1- 1/8" aluminum "fatbar". If you are thinking of going to a fatbar after you bend your stock set or just want the versatility and option to run any bar, this is the riser to go with. Reducers lock into risers to insure no slippage between components.
These risers use 8mm bolts. Always check and confirm that your bike has adequate cable and brake line length before installing any handlebar risers.
Anti-Vibration Risers may interfere with aftermarket large capacity fuel tanks, and some steering stem clamp configurations (in these cases we recommend using standard pivoting risers).
This unique design from Rox allows you to move your bars either closer (1" up and back) or further away (1" forward and 1-1/4" up) depending on rider preference. These risers have an oblong mounting hole so that they will fit virtually any triple clamp with 8mm bolts. A set of reducers lock into the risers ensuring no slippage whether you have a 7/8" or 1-1/8" bars.
Because these are offset there may be limited clearance between the gas tank and the risers when the bars are fully turned on some models, mainly when mounted to move the bars closer.
Protect your thumbs from blisters caused by riding on the inside of your grips.
Sold in Pairs.
The elegant, open-end design makes these heated grips both stylish and functional. Highly efficient design, delivering warmth faster than traditional heated grips. Five-level temperature controller adjusts the grips accurately to avoid overheating. Specially selected rubber material resists the outdoor environment and provides a secure and comfortable grip. Even at high-temperatures, the grip remains resistant to damage.
Choose from the standard five level push button temperature controller, or the LCD display controller which shows the selected heat level and available battery voltage.
The Apollo Heated Grips are designed with an integrated adjustable thumb switch, which allows them to easily fit on any kind of motorcycles on the market. The integrated thumb switch gives control to the rider to adjust the temperature level while keeping hands on the bar for a safer ride.
Its wide temperature setting range will keep the rider comfortable under the cold riding conditions.
The 5 color LED display will enhance the visual look of the heated grips and will allow the rider to quickly know at which heat level the grips are set.
This system will also detect if the battery voltage is too low and will automatically shut down the heated grips in order to make sure the rider have enough power to start the engine or use the motorcycle.
Specifications:
These heated grips from Koso have been tested by us and we can say they will keep your hands warm and give you the grip you need in off road conditions, thanks to the full diamond grip design.
These new heated devices are for the user that does not want to commit to changing their grips but still wants to maintain the comfort of heated grips. The fitment is intended to fit all sorts of handlebar sizes. They can be installed and removed in a matter of seconds and kept in any sport bag when not in use.
Features:
These grips feature a thicker design that dampens vibration. The soft shoulder allows ease of movement. Three wire-tie grooves are molded into the grip to make securing them a breeze. We think they are great!
ProTaper Pillow Top Grip with 3-D (Tri-Density) Technology. Try the grip with the technical advantage of three dedicated rubber compounds.
ProTaper Pillow Top Grip with 3-D (Tri-Density) Technology. Try the grip with the technical advantage of three dedicated rubber compounds.
The difference between the original Pillow Top and the Pillow Top Lite is the overall diameter of the grip surface. The Lite offers a smaller diameter so the grips don't feel as large reducing fatigue in your hands while riding.
Each pattern is available in three advanced synthetic rubber compounds. This means you can have the optimum combination of strength, tackiness and shock absorption to suit every riding condition and individual style. Soft grip is extremely soft, giving you a very comfortable ride, great feel and reduces the chance of blisters; however, because the grip is so soft, it wears quickly. Medium is a compromise between firm and soft. Firm grip has the same feel as a stock grip, it is very strong and has very good resistance to tearing and abrasion. Half Waffle has waffle pattern in finger area for traction and diamond pattern on palm side to reduce blisters. Full Waffle: designed after the CR Honda® grip.
This little jewel reduces hand fatigue and cramping on long rides or daily commutes. The Crampbuster is not a throttle locking unit but, rather a simple clip-on device which allows you to relax your grip while riding.
The Go Cruise cruise control mounts over the throttle grip and rests on the brake lever to hold your throttle open, allowing you to stretch and rest your hand on long rides. Installs and removes in seconds with no tools. You can roll off the throttle manually to disengage the Go Cruise.
CNC Machined high quality aluminum folding levers.
Lever folds outward to prevent breakage in the event of a crash.
Automatic lever position restoration provides quick recovery from the crash.
Ultra precision machine cut for super light weight construction, high precision and quality.
Available in 3 and 4 finger lever lengths to fit your riding style.
Made of durable aluminum for extreme strength. Titanium color anodized finish.
Sold Individually
CNC Machined high quality aluminum folding levers.
Lever folds outward to prevent breakage in the event of a crash.
Automatic lever position restoration provides quick recovery from the crash.
Ultra precision machine cut for super light weight construction, high precision and quality.
Available in 3 and 4 finger lever lengths to fit your riding style.
Made of durable aluminum for extreme strength. Titanium color anodized finish.
Sold Individually
Order up your new levers here! If you keep breaking levers, you might want to think about a set of handguards to protect them in case of a fall.
Attach this over your brake lever and hand grip, squeeze the brake lever, pull the locking bar in and lock the black portion down. This creates a locked front brake, making parking safe and secure with about 5 seconds of effort.
To unlock the BrakeFix, you just lift the back of the black hooking portion to release it. This takes about 2 seconds. Perfect for use with Snapjack type stands or just parking on an incline.
Forged aluminum, black anodized arm and Knurled CNC aluminum shift tip.
A high quality replacement clutch cable.
OEM throttle cable set for the CRF250L
*generic image, actual cables may look different.
The Folding Bar End Mirror has a beautiful case mirror backing plate and the arms are one-piece, eliminating screws and mirrors vibrating loose. The nylon swivel allows just the right amount of tension to be maintained for easy adjustment.
Features and Benefits:
This new mirror screws into your stock mirror mount but can be folded out of the way when it's time to hit the trails. These are quite similar to the very popular KTM folding mirrors but at half the price. Fits either left or right side.
Sold individually.
All Yamaha's will need a mirror adapter if you have the stock perch.
One folding mirror. Includes handlebar mount. Can be used on left or right side.
Sold individually.
This new mirror can be folded out of the way when it's time to hit the trails. These are quite similar to the very popular KTM folding mirrors but at half the price.
Fits either left or right side and includes handlebar mount.
Sold individually
With the split back, you don't need to remove your grip or throttle tube, just put it on and tighten 'er down. Put the mirror in and hit the road. Clean and simple.
Replaces all 2 bolt style clutch/brake lever mount clamps. Can help save space on short bend handlebars.
Can't see past your shoulders? These mirror extenders will get your mirrors higher and farther out for a much better view of the road behind you.
Sold individually.
The Adventure Kit is perfect for adventure and touring bikes where the mirrors are kept up most of the time. This mirror offers the widest field of view, and is ideal for riding paved and dirt roads. The 6 inch arm is a little longer than anything else on the market, for great visibility on loaded bikes.
The new Doubletake ball is oversized, and high quality nitrile rubber surrounds an aluminum base that won't degrade under extended compression.
The Doubletake Base Kit includes bolts to thread into every application (even reverse thread Yamaha's), without adapters.
ADV 6" Arm Mirror
Kit Includes:
Sold individually.
Enduro Mirror 4"
The Enduro Kit is a great option for your street legal dirtbike if you fold away your mirrors often. The longer stem helps the reflector fold behind the headlight and gives good visibility when extended.
Their Doubletake Arm 3.5" is perfect for aggressive riders- long enough to see, but small enough to tuck away.
The new Doubletake ball is oversized, and high quality nitrile rubber surrounds an aluminum base that won't degrade under extended compression.
The Doubletake Base Kit includes bolts to thread into every application (even reverse thread Yamaha's), without adapters.
The Trail Mirror is a simple solution for any dirtbike or mountain bike. Gives you hindsight when you need it, but you forget it's there otherwise.
Zip ties directly to the bar- no hardware required.
Sold individually
PSR dual sport mirrors come with a slightly convex mirror for a wider field of vision behind you. The round mirror is 4.25" in diameter while the oval is 3.75" x 3". These mirrors are easily adjustable and fold out of the way quickly with the 1" RAM mounts.
The RAM Ball Stud Base used for both mirrors will go into any standard 10x1.25 threaded mirror base.
Sold individually.
All Yamaha's will need a mirror adapter if you have the stock perch.
Keep your cables lubed up and working freely, with Motion Pro's Cable Luber. This tool is used to inject lubricant into any cable housing. Clamps over housing and cable allowing an aerosol can with nozzle to be connected. Once the lubrication solution runs out the far end, the cable is lubricated.
Designed to seal completely around the cable housing and stop all those messy leaks. With the unit closed and sealed around the cable, your cable gets better lubrication and you waste less lubricant.
These are the first batteries with built-in jump starting. They intelligently monitor their status, and just before going completely dead, puts itself to sleep with just enough energy to get your vehicle started again. Simply press the RE-START button located on the battery, start your bike and ride away.
These are an extremely lightweight (2.5 lbs.) high-powered Lithium-Ion replacement battery for motorcycles. These batteries offer the first Battery Management System (BMS) found on a powersport battery and includes low-voltage cut-off, over discharge, over-charge, and thermal protections with real time lithium-ion cell balancing. Use of a lithium specific charger to maintain the life of the battery is highly recommended.
Product Size is 8.4"L x 5"W x 2.2"H. If you need spacers, select the optional Foam Kit to pad the battery in the battery box.
Built with the latest in Lithium Ion Polymer Technology. All components are designed, manufactured, assembled and packed in one location assuring high quality and consistency. Besides it's extreme lightweight (50% to 70% lighter than standard lead-acid batteries) it also features a built-in LED test gauge and the ability to mount it in any position. There is no hazardous acid or heavy metals and it is non-explosive and non-combustible.
The Firepower features Increased cranking amps over lead acid batteries and has a very fast recharge cycle and can be brought up to a 90% charge within 6 minutes and also has 6 to 12 times more cycle life when compared to lead acid batteries. A 2-year warranty insures that your investment is protected.
145 CCA 12V/28.8WH
Package Dimensions: 4.75" x 3.00" x 4.50
The Shorai LFM Standard Recommendation is the best overall pick for most applications, and has been selected to give strong cranking performance and long lifespan.
Measures 4.5" x 3.5" x 2.28"
Weight (lbs): 1.34 lbs
Weight (kg): 0.61 kg
Cold Cranking Amps: 135
Polarity: [- +]
Each Shorai battery includes self-adhesive foam panels to achieve a snug fit in your battery box.
The Shorai LFM Duration Recommendation is the best overall pick for most applications, and has been selected to give strong cranking performance and long lifespan.
Measures 4.45" x 3.5" x 2.28"
Weight (lbs): 1.52 lbs
Weight (kg): 0.69 kg
Cold Cranking Amps: 210
Polarity: [- +]
Each Shorai battery includes self-adhesive foam panels to achieve a snug fit in your battery box.
This is an adhesive-backed foam kit, for the installation of small batteries into larger battery tray areas. Keep in mind that all Antigravity Small Case Batteries DO come with adhesive-backed foam in the box. This kit is for when you need extra foam or are doing installation in another vehicle.
Features
This is the Restart-Remote for Antigravity RE-START (RS) Powersport Batteries with jump-starting built-in. You no longer need to access the battery to press its Re-Start button in the event you over-discharged the battery. Simply plug this accessory into your Battery’s Charging Cable to remotely awaken the RE-START Battery! No need to remove the seat or a fairing to get to the Battery.
The LITHIUM US is an advanced microprocessor-controlled charger specially designed to recharge and maintain the cells of Lithium-Iron (LiFePO4) batteries – maximizing their performance and lifespan. With up to 4.3A of charge current available the LITHIUM US is extremely flexible and will charge LiFePO4 batteries from 5Ah to 60Ah and maintain up to 120Ah.
The operation is simple and charging will commence upon connection. With no need to disconnect the battery from the vehicle, the LITHIUM US will automatically reset any low voltage protection electronics (Battery Management System) fitted. Charging can be restarted manually at any time using the ‘Reset’ button.
The CTEK LITHIUM US is a fully automatic ‘connect and forget’ charger with 8 charging steps including a testing sequence to show if the LiFePO4 battery can take and retain the charge, a unique maximization step to restore full capacity, and patented maintenance charging to ensure maximum performance even after months of inactivity. Splash-proof and dust-proof (IP65) the LITHIUM US is easy and safe to use, protects vehicle electronics, is spark-free, is reverse polarity protected and short circuit proof. The LITHIUM US features a 5-year warranty.
The CTEK Brand of chargers is recommended for all Antigravity RE-START (RS) Batteries (models with built-in jump-starting and full BMS protections)
