Africa Twin (CRF1100L)

ProCycle's custom calendar features specially selected customer submitted photos from around the world. Real riders on real adventures.

Each of the two calendar sizes will feature different pictures. Even more reason to get both!

The desk top is 6" by 3.75" the perfect size to sit on your desk.

The wall calendar is 12" by 18" when fully open for use on any wall. Marks USA holidays and moon cycles.

The three images featured are the finalists in this years photo contest who will all be featured in the wall calendar for 2025.

Hardened chrome vanadium steel with built in rubber insert to hold spark plug steady.

Thin wall bi-hex sockets designed to access narrow spark plug holes.

Fits 3/8" square drive and hex drive, 14mm, 16mm, 18mm, 21mm.

• Contains degree wheel, standard unit indicator, adjustable magnetic stand, and three positive stops (10 mm, 12 mm and 14 mm threads)
• Can be used to install and adjust timing of any cam
• Wooden carrying case

Made from medium carbon steel with hardened jaws. It features spanner pins and the jaws open up to 5" wide. It's ideal for holding clutch hubs, flywheels, gears, sprockets, etc. Made by Motion Pro.

This tool is designed to separate vertically split crank case halves on two and four stroke engines. Adjustable arms allow it to be used on multiple bolt patterns found on a variety of makes and models of motorcycles. Industrial grade steel construction with black oxide finish for long service life. Comes with 8mm mounting bolts and 6mm adapters. Protective carrying case included.

For easy removal of recessed oil filters.

Conical point screws pierces and grabs the metal end cap of the filter.

reduces potential damage to the engine cases.

NOT for use on re-usable oil filters.

A 3-pack of easy to apply strips measure the temperature of engine, suspension, and radiator components. Temperature range 149° to 248°

Thread Chasers are designed to clean and re-cut damaged aluminum threads.

This kit contains the two sizes most common on metric motorcycles, M6x1.0 and M8x1.25.

Thread Chasers also remove dirt and metal shavings that become captured in thread grooves.

Uses 8mm or 10mm hex sockets, a Must for all tool kits.

• 26 straight blades
• SAE and metric markings
• Check for clearance on valves, ignition points etc.
• Includes 26 blades varying in thickness from .0015"/.038 mm to .025"/.635 mm

Genuine Keihin spring, washer, and oring for the fuel screw of FCR and FCR MX carbs.

Just the parts…
Fuel screw spring, washer, o-ring (fuel screw not included)

Sold in 6 packs

• Compatible with many air filter boxes. Easy to install by drilling 1’’ holes in airbox housing and snap fitting vents in.
• May be cleaned and re-oiled
• More air flow allows you to add more fuel to your intake mixture, increasing performance.
• 1" Diameter

Not legal for use on pollution controlled vehicles in the state of California.

Quick release one-piece clamps that saves space. These are great for fuel lines, controlling wires, and can be used many times.

Comes with 4 each of 8mm, 9mm 10mm, and 12mm.

No special tools needed, from Helix Racing.

TechSpec’s Motorcycle Tank Grips were developed to improve body, bike control and increase riders comfort. Gripping your motorcycle between your knees or thighs improves overall control of your ride by better securing your body weight and seat position under the forces of braking, cornering and acceleration while also relieving pressure from your wrists, elbows, shoulders and lower back giving you increased control and a more comfortable, safer ride. Snake Skin is a thin, .125” medium durometer “rubber” material that offers a secure, comfortable grip, durable protection and a clean stock look.

This universal precut kit includes left and right tank grips. (8" X 3") Triangle

Security for your fuel tank. Includes 2 keys. Internally vented with a check valve that prevents spillage in case of a tip over.

  Fits Acerbis, IMS and Safari tanks only.

If you're like us, you hate the long floppy vent hose hanging off the cap of your aftermarket tank.

This one-way vent cap replaces the long hose with a short one only about 2" long. It allows air into your tank but prevents fuel from sloshing out.

Machined from billet alloy and anodized for good looks.

  Not for stock fuel tanks!

The small size and right angle hose barbs make this filter easier to fit into the small space between your fuel petcock and carburetor. Filter body is only 7/8" diameter. Straight filter is 2" long, 90 degree filter is only 1-5/8" long.

This filter is meant for 5/16" fuel lines. Only 1/2" thick it is small enough to fit just about anywhere.

Fuel supplies can be sketchy at times. This filter lives in your tank to trap dirt and debris as it is poured into the tank. Features a custom shaped adapter that fits securely under the gas cap, creating a leak-proof seal. If it stays out of your fuel, it can't get into the carburetor! Created by the filter experts at Twin Air, this filter fits IMS,  Acerbis and Safari brand gas tanks.

All of these lines are stronger and more durable than vinyl fuel lines and are resistant to swelling, UV light, as well as hardening and cracking.

All of these lines are stronger and more durable than vinyl fuel lines and are resistant to swelling, UV light, as well as hardening and cracking.

Ordering new fuel line? How about a set of fresh zinc plated clamps to go with it?

These will be sure your fuel line stays connected. A pack of 8 clamps in 2 sizes to fit most 1/4 or 5/16 fuel hose.

Hose reducer to go from 5/16" line down to 1/4" line. Many bikes have 5/16" carburetor spigots but most aftermarket petcocks are 1/4". This solve the problem of mismatched sizes. Solid brass construction. Can be used to route or repair fuel lines, oil lines or air lines. Barbed ends provide a secure fit.

Need to mount two containers? A water and a fuel? Two waters? Already have a RotoPax Mount for a single container? Get this extender to work in conjunction with a pack mount and that will be no problem! Single mount, two containers.

RotoPax holder made to mount a single Fuel and/or Water container.

Need to mount two containers? A water and a fuel? Two waters? Get the extender which allows you to stack two containers no problem! Single mount, two containers

RotoPax holder made to mount a single Fuel and/or Water container.

This unique design adds strength and provides extra tightening power.

Use with included base plate or remove plate to attach mount direct by bolting up through the bottom or down through the top.

RotoPax are Rotational Molded - the process which produces indisputably superior products.

• Thicker walls and stronger construction
• Bright colors that are less prone to fading
• Extra threads, thicker walls, and sure-seal gasket guarantee no leaks

Need to mount two containers? A water and a fuel? Two waters? Finally, you can stack multiple packs together! Use in conjunction with a pack mount. You will need to purchase the Single Mount as well as the Extender.

Auxiliary fuel tanks mount to handlebars, forks, or rear racks.

• Suitable for minis, trials bikes, full size bikes, and anywhere else a little extra fuel is needed.
• Each tank includes a siphon kit that connects the tank to the main fuel tank and automatically siphons fuel while the bike is being ridden.
• With this design, the auxiliary tank empties first, before the main tank.
• Does not interfere with headlight, handguards, rear seat, etc.

This Super Siphon has  a (1/2 inch x 6 foot) long hose, which makes it quite easy to transfer fuel from one bike to another! Simply, shake the hose to prime it and get fuel moving. The hose is resistant to gasoline and any other hazardous chemicals. Roll it up, stuff it in your bag and you will be very happy whenever you need it.

Comfortable Oversize (or Fat Bar) Handlebars.

• Black in color. 
• Made from 5mm, proprietary, 2000 series T6 aluminum alloy for superior tensile and yield strength.
• Lighter and stronger than regular bars
• No-crossbrace allows flex to reduce shock and rider fatigue
• Oversize 1-1/8" diameter base reduces to 7/8" to allow standard-size controls/grips
• Etched alignment marks for fast and accurate positioning
• Bar pad included
• Works with stock controls and cables.

For bikes with factory 7/8" handlebars these will require the use of a 7/8 to 1-1/8  adapter (sold separate).

These 7/8" bars fit in the stock clamps and raise your grips a couple inches. They look great too!

• Adapt 7/8" bar mounts to accept oversized 1-1/8" handlebars
• An economical alternative to replacing expensive top triple clamps
• Include mounting bolts.

• 4.75" wide,
• Raises handlebars 2 inches and allows fore/aft position adjustment
• Provides dual pivot points for optimal bar positioning
• One piece design is made from solid aluminum for superior strength
• Available for 7/8" - 7/8" or 7/8" - 1 1/8" bars

Requires 7/8" factory bar clamps on bike

These versatile Risers allow you to clamp a 7/8" diameter handlebar or you can remove the 7/8" reducers and then clamp an 1- 1/8" aluminum "fatbar". If you are thinking of going to a fatbar after you bend your stock set or just want the versatility and option to run any bar, this is the riser to go with. Reducers lock into risers to insure no slippage between components.

These risers use 8mm bolts. Always check and confirm that your bike has adequate cable and brake line length before installing any handlebar risers.

Anti-Vibration Risers may interfere with aftermarket large capacity fuel tanks, and some steering stem clamp configurations (in these cases we recommend using standard pivoting risers).

This unique design from Rox allows you to move your bars either closer (1" up and back) or further away (1" forward and 1-1/4" up) depending on rider preference. These risers have an oblong mounting hole so that they will fit virtually any triple clamp with 8mm bolts. A set of reducers lock into the risers ensuring no slippage whether you have a 7/8" or 1-1/8" bars.

Because these are offset there may be limited clearance between the gas tank and the risers when the bars are fully turned on some models, mainly when mounted to move the bars closer.

Protect your thumbs from blisters caused by riding on the inside of your grips.

Sold in Pairs.

Highly efficient design delivers warmth faster than traditional heated grips.

Choose from the standard five level push button temperature controller, or the LCD display controller which shows the selected heat level and available battery voltage.

The Apollo Heated Grips are designed with an integrated adjustable thumb switch, which allows them to easily fit on any kind of motorcycles on the market. The integrated thumb switch gives control to the rider to adjust the temperature level while keeping hands on the bar for a safer ride.

Its wide temperature setting range will keep the rider comfortable under the cold riding conditions.

The 5 color LED display will enhance the visual look of the heated grips and will allow the rider to quickly know at which heat level the grips are set.

This system will also detect if the battery voltage is too low and will automatically shut down the heated grips in order to make sure the rider have enough power to start the engine or use the motorcycle.

Specifications:

• Integrated thumb switch designed for easy installation and control.
• “Plug & Play” wiring connections to shorten the installation time.
• Wide temperature settings for various weather conditions.
• Low Battery Warning protection to ensure the motorcycle has enough power to start.
• 5 color LED Indicators for the rider to quickly know in which heat level the grips are set.

These heated grips from Koso have been tested by us and we can say they will keep your hands warm and give you the grip you need in off road conditions, thanks to the full diamond grip design.

• Clamp-on grips do not need adhesive
• External temperature controller with 5 heat levels
• For use with twist throttle; includes interchangeable throttle cams
• Requires 35W and draws 2.5 amps per pair; low voltage shut off

These new heated devices are for the user that does not want to commit to changing their grips but still wants to maintain the comfort of heated grips. The fitment is intended to fit all sorts of handlebar sizes. They can be installed and removed in a matter of seconds and kept in any sport bag when not in use.

Features:

• Universal fit to be clipped on any handlebar sizes
• Rubber material that is resistant to outdoor conditions and high temperatures
• Thin and flexible silicone wires make them easy to install

• Ergonomically designed
• Medium-density Thermoplastic Rubber (TPR) compound provides excellent feedback and control, without sacrificing durability
• Full diamond pattern for an unparalleled feel in both wet and dry conditions
• Inner diameter optimized to keep grips secure in any conditions
• 115mm overall length; fit 7/8" bars and throttle sleeves

• Feature the classic Vans waffle sole pattern with a subtle domed center section for improved ergonomics and vibration dampening
• 125mm in length
• Fit 7/8" bars
• Sold in pairs

These grips feature a thicker design that dampens vibration. The soft shoulder allows ease of movement. Three wire-tie grooves are molded into the grip to make securing them a breeze. We think they are great!

ProTaper Pillow Top Grip with 3-D (Tri-Density) Technology.  Try the grip with the technical advantage of three dedicated rubber compounds.

• Vibrasonix pillow top reduces vibration and cushions impact. 
• Inner core compound perfects the bonding interface with bars. 
• Anti-Rip Tip™ uses denser compound to increase life of grip. 
• Designed to self-clean and shed mud away from outer surface. 
• Tacky gel-like surface compound is perfect for the trail and MX.

ProTaper Pillow Top Grip with 3-D (Tri-Density) Technology.  Try the grip with the technical advantage of three dedicated rubber compounds.

The difference between the original Pillow Top and the Pillow Top Lite is the overall diameter of the grip surface. The Lite offers a smaller diameter so the grips don't feel as large reducing fatigue in your hands while riding.

• Vibrasonix pillow top reduces vibration and cushions impact. 
• Inner core compound perfects the bonding interface with bars. 
• Anti-Rip Tip™ uses denser compound to increase life of grip. 
• Designed to self-clean and shed mud away from outer surface. 
• Tacky gel-like surface compound is perfect for the trail and MX.

Each pattern is available in three advanced synthetic rubber compounds. This means you can have the optimum combination of strength, tackiness and shock absorption to suit every riding condition and individual style. Soft grip is extremely soft, giving you a very comfortable ride, great feel and reduces the chance of blisters; however, because the grip is so soft, it wears quickly. Medium is a compromise between firm and soft. Firm grip has the same feel as a stock grip, it is very strong and has very good resistance to tearing and abrasion. Half Waffle has waffle pattern in finger area for traction and diamond pattern on palm side to reduce blisters. Full Waffle: designed after the CR Honda® grip.

This little jewel reduces hand fatigue and cramping on long rides or daily commutes. The Crampbuster is not a throttle locking unit but, rather a simple clip-on device which allows you to relax your grip while riding.

The Go Cruise cruise control mounts over the throttle grip and rests on the brake lever to hold your throttle open, allowing you to stretch and rest your hand on long rides. Installs and removes in seconds with no tools. You can roll off the throttle manually to disengage the Go Cruise.

Attach this over your brake lever and hand grip, squeeze the brake lever, pull the locking bar in and lock the black portion down. This creates a locked front brake, making parking safe and secure with about 5 seconds of effort.

To unlock the BrakeFix, you just lift the back of the black hooking portion to release it. This takes about 2 seconds. Perfect for use with Snapjack type stands or just parking on an incline.

• Handy, compact kit for on-the-go emergency throttle, clutch and brake cable repairs
• Includes 2 different diameter 6.5 long inner cables and an assortment of cable ends

Bar end mounted mirrors move the mirrors out past your elbows so you can actually see what is behind you. They can mount with or without hand guards.

Sold in Pairs

This new mirror screws into your stock mirror mount but can be folded out of the way when it's time to hit the trails. These are quite similar to the very popular KTM folding mirrors but at half the price. Fits either left or right side.

Sold individually. If a set is needed, order two.

  All Yamaha's will need a mirror adapter if you have the stock perch.

One folding mirror. Includes handlebar mount. Can be used on left or right side.

Sold individually.

This new mirror can be folded out of the way when it's time to hit the trails. These are quite similar to the very popular KTM folding mirrors but at half the price.

Fits either left or right side and includes handlebar mount.

Sold individually

With the split back, you don't need to remove your grip or throttle tube, just put it on and tighten 'er down. Put the mirror in and hit the road. Clean and simple.

Replaces all 2 bolt style clutch/brake lever mount clamps on your clutch or brake lever holder. Can help save space on short bend handlebars.

Can't see past your shoulders? These mirror extenders will get your mirrors higher and farther out for a much better view of the road behind you.

Sold individually.

The Adventure Kit is perfect for adventure and touring bikes where the mirrors are kept up most of the time. This mirror offers the widest field of view, and is ideal for riding paved and dirt roads.  The 6 inch arm is a little longer than anything else on the market, for great visibility on loaded bikes.

• Made from super tough glass reinforced zytel
• Reflector Dimensions: 5.25" x 3.5" (135mm x 95mm) 
• Overall mirror length: 7" (175mm) (not including arm mount)
• Convex lens meets SAE and CE specifications 
• Mirror mounts to any 10mm perch.

The new Doubletake ball is oversized, and high quality nitrile rubber surrounds an aluminum base that won't degrade under extended compression. 

The Doubletake Base Kit includes bolts to thread into every application (even reverse thread Yamaha's), without adapters. 

Sold individually.

The Trail Mirror is a simple solution for any dirtbike or mountain bike. Gives you hindsight when you need it, but you forget it's there otherwise. 

• Made from super tough glass reinforced Zytel
• Reflector diameter: 2" (50mm)
• Bar space: 0.75" (19mm), Height 1.25" (32mm)
• Convex lens for wider field of view

Zip ties directly to the bar- no hardware required.

Sold individually

PSR dual sport mirrors come with a slightly convex mirror for a wider field of vision behind you. The round mirror is 4.25" in diameter while the oval is 3.75" x 3". These mirrors are easily adjustable and fold out of the way quickly with the 1" RAM mounts.

The RAM Ball Stud Base used for both mirrors will go into any standard 10x1.25 threaded mirror base.

Sold individually. If you need a set, please order 2.

 All Yamaha's will need a mirror adapter if you have the stock perch.

Keep your cables lubed up and working freely, with Motion Pro's Cable Luber. This tool is used to inject lubricant into any cable housing. Clamps over housing and cable allowing an aerosol can with nozzle to be connected. Once the lubrication solution runs out the far end, the cable is lubricated.

Designed to seal completely around the cable housing and stop all those messy leaks. With the unit closed and sealed around the cable, your cable gets better lubrication and you waste less lubricant.

• Works on most cables with a 4mm - 8mm O.D. housing.

This is an adhesive-backed foam kit, for the installation of small batteries into larger battery tray areas. Keep in mind that all Antigravity Small Case Batteries DO come with adhesive-backed foam in the box. This kit is for when you need extra foam or are doing installation in another vehicle.

Features

• Hi Density adhesive backed foam
• Help reduce vibration
• Easily cuts with scissors or razor knife
• 3 pieces of 6″ x 3″ x 0.5″ adhesive-backed foam

This is the Restart-Remote for Antigravity RE-START (RS) Powersport Batteries with jump-starting built-in. You no longer need to access the battery to press its Re-Start button in the event you over-discharged the battery. Simply plug this accessory into your Battery’s Charging Cable to remotely awaken the RE-START Battery! No need to remove the seat or a fairing to get to the Battery.

• Compatible with Antigravity RE-START Powersport Batteries
• Plugs into SAE Tip of your existing battery charging cable
• Comes with protective zipper case
• Remote requires 9v battery (not included)
• Not compatible with Automotive Batteries

The LITHIUM US is an advanced microprocessor-controlled charger specially designed to recharge and maintain the cells of Lithium-Iron (LiFePO4)  batteries – maximizing their performance and lifespan. With up to 4.3A of charge current available the LITHIUM US is extremely flexible and will charge LiFePO4 batteries from 5Ah to 60Ah and maintain up to 120Ah.

The operation is simple and charging will commence upon connection. With no need to disconnect the battery from the vehicle, the LITHIUM US will automatically reset any low voltage protection electronics (Battery Management System) fitted. Charging can be restarted manually at any time using the ‘Reset’ button.

The CTEK LITHIUM US is a fully automatic ‘connect and forget’ charger with 8 charging steps including a testing sequence to show if the LiFePO4 battery can take and retain the charge, a unique maximization step to restore full capacity, and patented maintenance charging to ensure maximum performance even after months of inactivity. Splash-proof and dust-proof (IP65) the LITHIUM US is easy and safe to use, protects vehicle electronics, is spark-free, is reverse polarity protected and short circuit proof. The LITHIUM US features a 5-year warranty.

The CTEK Brand of chargers is recommended for all Antigravity RE-START (RS) Batteries (models with built-in jump-starting and full BMS protections)

Spare Extension Cable Set for Shorai 12V LFX battery charger.

The Battery Tender® Junior Selectable is much more than a trickle charger. It has a brain. It's lightweight, compact, and fully automatic; very easy to use, especially in small spaces. It will keep your Lead Acid, AGM or Lithium battery fully charged so that it is ready to go when you are

• Output: 12v @ 800mA
• Selectable Battery Chemistry- has battery chemistry selection with proper charge algorithm for lead-acid, flooded or sealed maintenance free (AGM and gel cell), and Lithium Non-RS/Non-BMS batteries
• Complete 4-step charging program (Initialization, Bulk Charge, Absorption Mode, Float Mode)
• Automatically switches to float/maintenance voltage after fully charging the battery
• If the battery voltage drops too far under load, full charger output power resumes
• Solid state two color LED indicates stage of charger
• Spark proof, reverse polarity protected
• 12' output cord
• Meets California and Oregon appliance energy efficiency standards for battery charging systems
• 5 year warranty

Charges and maintains all 12 volt lead acid, gel and lithium iron phosphate (LiFePO4)/lithium ion polymer Non-RS/Non-BMS powersport batteries

Features:

• CONSTANT CURRENT CHARGE - If the battery voltage is over 10 volts, the charger will deliver a 2 amp charge until the battery reaches 14.2 volts.
• MAINTENANCE CHARGE - When the battery reaches 14.2 volts, the charger will automatically convert to maintenance mode. The charger will revert to charge mode when the voltage drops below a specified voltage.
• LOW VOLTAGE RECOVERY - If battery voltage is below 8 volts, the charger will apply a .2 amp charge to recover the battery, once the battery reaches 8 volts, the charger will apply a .5 amp charge, at 10 volts a full 2 amp charge is applied until the battery is fully charged.
• AUTOMATIC VERIFICATION STAGE - Charger automatically stops charging if the battery does not reach at least 10 volts after 2 hours of charging.
• SAFETY - Power is not passed thru the charging leads unless they are connected to a battery.
• LED indicator light shows charging status.
• Includes heavy duty clamps and fused ring terminal SAE adapter.

You can charge your Shorai battery with a regular battery charger but, if you want the very best for it this charger is designed for optimum performance by balancing the individual cells in the battery. Balanced charging ensures the battery reaches its fullest capacity and longest life. 'Store' mode allows long term maintenance storage.

Shorai Charge/Store Dedicated Battery Management System for Shorai LFX only. 2A Max charge rate, connects via BMS 5-pin port on LFX batteries. Includes modes for full charge, or long-term storage. Input USA 110~120V 50/60 Hz.

  For Shorai Lithium Iron batteries only

GET JumpStarter Mini, the second-generation, multifunctional jump starter. Now lighter and smaller, it's ready to help you restart any motorcycle or scooter when the battery is low. You can also use the powerful built-in LED flashlight or charge your use it as a power bank to charge your electronic devices. JumpStarter Mini comes together with a hard, water-resistant case perfect for carrying it anywhere and protecting it on your journeys.

• Light and compact multifunctional mini starter
• Allows restart of motorcycles and scooters when they are out of battery
• Can also be used as a Power Bank for electric devices thanks to the USB output port
• USB 5V2.4A output allows connection to tablets, smartphones, MP3 etc.
• Has built-in LED flashlight
• Easy to use; provides special protection against overvoltage and inversion of power supply polarity
• Start current: 200A, peak current: 400A, operating temperature range of -20°C to 60°C
• Includes JumpStarter, Smart Cable, 3-in1 USB cable and user instructions
• Measures 155 mm x 79 mm x 16 mm

A portable device that can jump-start your motorcycle or car. It can also charge your cell phone, GPS unit, laptop or other electronic devices via USB cable.

• XP-1 is 6" x 2 7/8" x1" 14oz.
• XP-3 is 5" x 2 7/8" x 1" 12oz.
• Holds a charge for up to 1 year.

• Mini Speedometer is only 2 inches diameter.
• Works with Japanese speedometer or odometer cables.
• Mounts to handlebar bolt or use the bar clamp supplied.
• Illuminated dial for night riding.
• Smaller, lighter and more accurate than the stock unit.

Keep your smartphone, GPS and/or MP3 charged while enjoying your ride. Water- and weather-resistant, the Dual USB Port/Plug Charger offers you 5-Volt/2-Amp dual USB ports that have an inline fuse for protection. It comes with 38" of wire and 12" long battery quick connect rings. The mounting bracket that is included fits 7/8" and 1" bars.

The Optimate Cable O-20 is a SAE weatherproof bulkhead/panel mount power source. Main body fits a 1" dia. hole. Overall length of the unit is 12" from top of bulkhead to end of connector. Both connectors are industry standard 2-pin SAE connectors. We also offer an optional stainless steel bracket that you can bolt on wherever you like. This makes a clean installation and you won't have a charging cable hanging loose.

Cable max. rating is 10 Amps. Includes an in-line rubber seal at the connector end and a protective cover at the bulkhead for when you don't have something plugged in. Unit has a 3-year limited warranty.

Don't have an SAE plug attached to your battery? Choose the add on below.

This USB device connects to a battery cable with an SAE connector just like the typical Battery Tender outlet, and allows you to charge your electronic devices. Input is 12 Volts, with an output to the USB port of 2.1A maximum, perfect for your phone or other USB devices.

Laser cut from stainless steel. This is a quick and easy bracket for mounting a key switch, panel mount, bulkhead fitting or anything that requires a 1 inch hole.

Open Trail Terminal Tender blocks allow you to add up to six different accessories on your battery.

Features:

• Fits any 12v powersports battery with square posts
• Three mounting options: side, front, and top
• Includes two blocks (+) and (-) and 8 button head bolts

The standard ring connector is a simple, quick connection with a fused positive ring cable and negative cable that attaches directly to your battery with an industry standard 2-pin, SAE connector.

The weather protected ring connector is a premium quick connect permanent battery lead with weather protected connection system and cable. It features 1/4"/M6 ringlets, 20" L, Industry standard 2-pin, heavy-duty SAE connector, 15A fuse, Cable max rating: 5 Amps, Cable remains flexible at below freezing temperatures; rated for -40°F/-40°C.

• Permanent battery leads with integrated battery status/charge system monitors for 12V lead-acid batteries or lithium batteries
• Monitor charge or confirm if the charging system is working correctly
• SAE charge port with weatherproof sealing cap
• Two automatic modes: battery charge level monitor and charging system test

This bright and compact 6-LED flashlight plugs right into your SAE battery charging socket for hours of light. In addition, it has a charging system check that lets you know if your bike is charging properly. It features a 40 inch cord so you can see in those out of the way places when you need to.

Small 2 3/4" diameter motorcycle horn. Works on 12v DC. Sound will be diminished when running on AC.

• High sound level 105-118 db
• 80mm diameter and only 7.5 oz
• Wire extension included
• Universal for street and off road use

Deltran quick-connect plug with LCD voltmeter display. Plug this into your Battery Tender, or any SAE cable, for an LCD display of the battery voltage. Three LED lights indicate the state of charge as well.

A digital voltmeter that can be mounted almost anywhere, on any bike, thanks to ProCycle's multi-position stainless steel bracket. Keeps you informed on the status of your charging system.

Completely waterproof and comes with connectors, wires and thorough instructions. A "must have" device for riders who use heated riding gear, heated grips, additional lighting, GPS, etc.

• Compact, adhesive back
• Easy-to-read display
• Flashing low voltage warning
• Measures 1.57" diameter x .43" D
• Effective temperature range: 14 ~ 140 °F

So you say you want more light for your dual sport? Give this 7"DOT legal Rally light a try and light it up like a freight train! HIGH/LOW operation and SAE/DOT/E4 approved. 
 This light does not have the large Cyclops logos shown on one of the images.

• Race Inspired Design
• Hella reflector, made in Germany  stamped SAE/E4
• Lightweight Aluminum Frame
• Plug and Play for Bikes with H4 Bulbs.
• Available with optional mounting plate for computer or GPS
• Easily converted to HID if desired, uses an H4 bulb
• For bikes that are not H4 (XR650R), a simple H4 plug available at any auto parts store will allow you to use this light.
• Now the panel on top of the light for mounting speedos/gps's etc is included, (This is a platform, not actual GPS mount.)

Optional 10.0 Lumen LED High/Low Upgrade  and now the Phoenix LED complete headlight for the ultimate DOT headlight
The stock lamp that comes with this rally light is great, but you can get  well over double the brightness  with the LED upgrade at a substantially lower power draw. Note if your bike is ac powered at the headlight you will need the rectifier for the LED option.. AKA carbureted KTM's CRFX and XR400/650.. others may apply.

Each 10 watt Solstice Solo produces 900 lumens, which is roughly equal to a 50 watt halogen bulb. These are one of the brightest LED off road lamps on the market. The rugged and compact 2” x 2” square die-cast aluminum housing makes mounting easy. The Solstice Solo also features a 4 sided channel design that allows you to interlink it on all four sides with other Solstice Solo pods. Includes stainless steel mounting bracket and waterproof connection. Choose narrow, medium, wide or elliptical light beam pattern. Our favorite is the Elliptical pattern which is wide and flat, putting most of the light where you need it the most.

Sold each.

A game changer in compact auxiliary lights. High output, compact and lightweight!

The New Cyclops Aurora 2 inch lights rated at 4000 lumens for the a set. Using an authentic top binned Cree XHP50 emitter these lights pack a punch!

Available with or without the daytime Running light option (DRL) which can also be a front blinker. (you may need a led flasher to do that)

Like all Cyclops lights we only use the Best Real Cree emitters. R113, R10 TUV and Emark certified IP68 rated.

Includes a full relayed wire harness designed for a Motorcycle. No need to use a switch if running the DRL version, also no need for a switch if using the skene dimmer or want the lights on in high beam and off in low beam. The factory switch will work for these applications. Unless you have a LED factory headlight in a R1200gs,850Gs or KTM1290 these bikes will require our Raider canbus controller.

Look at these quality features!

• Solid Steel cradle mount. No broken or cracked mounts!
• CNC machined aluminum housings
• Polycarbonate lenses, Break-proof!
• 15 degree beam patterns, a great choice for distance and field of view.
• 19 watts each
• 2000 lumens a piece, 4000 lumens for the set.
• Includes a relayed wire harness
• Input voltage 9-30VDC
• R113, R10 TUV and Emark certified
• IP68 Rated

Available in two wattage configurations: 30 watts and 42 watts, which produce luminous outputs of 5000 lumens and 7000 lumens, respectively. If your motorcycle's electrical system cannot accommodate these wattages, the light can be operated in low beam mode, resulting in a 50% reduction in power consumption. When additional illumination is required, users can easily switch to high beam mode.

Despite its compact size, this LED light is designed to deliver substantial luminous output. Its performance surpasses that of other mini LED lights in the market.

The light is equipped with a durable push-button switch, metal handlebar mounts, and adaptable options that allow for compatibility with various motorcycle configurations. It features components such as switches, cords, strain reliefs, and optics that are engineered for enhanced water resistance, robustness, and overall performance.

Tailored specifically for snowbike applications, this light boasts a compact design with significant output capabilities. Enhanced heat is directed to the lens, facilitating snow melting and enabling continuous riding.

This light is ideal for users seeking a lightweight solution to comply with legal requirements for headlights while also being sufficiently powerful for racing and trail riding.

Installation is straightforward, with the light mounting easily to a number plate; however, the use of the recommended stainless steel platform mount is advised for improved convenience. The light operates using the motorcycle's battery power.

The Explorer light bar is equipped with a GoPro-compatible mount and an aluminum platform, allowing for versatile mounting options. A handlebar mount is provided for central positioning on the handlebars. (Fits all stock 7/8 and 1 1/8 bars. Not for flexbars) Notably, there are no plastic components in the light head assembly.

Included with the product is a rubber-covered switch that can be mounted on the handlebars, offering three power settings: off, 50%, and full brightness.

The light features a combo beam pattern, integrating spot, driving, and wide beam configurations into a single unit.

Now a lifetime warrantied LED light set at a budget friendly price.. and Not made in China.

The new Cyclops Pegasus led light set comes complete with a high quality relayed wire harness and a potent combo light beam pattern.

We are able to offer this fantastic light at a great price due to a one piece optic and sealed beam construction, eliminating extra parts and creating a very durable and high performance light.

These lights in white feature 7 watt emitters (28 watts per light) with two 10 degree and two 25 degree optics, Good for 500 plus ft of lighting (white).

The amber version is a Cree 3 watt emitters (12 watts per light).

This combo beam pattern offers good forward lighting and extremely good conspicuity.

The light set is available in white 5600K or a extremely bright Amber, perfect to allow those autos to see you. Lightweight and robust at 2.75 inches with a single stud mounting, they fit just about anywhere you would like to mount your lights.

Specs:

• Canbus compatible, full relayed wire harness included
• 5000 plus lumens for the set
• 28 watt draw per white light, 12 watt draw per amber light
• ISO 67... waterproof
• 5600K (white 33% brighter than Amber)
• Life time warrantied
• Sold as a pair

The Mojave Series LED Racing Lights have been designed to survive and operate in extreme conditions. Lights feature a heavy duty housing that can withstand hard impacts and a lens that is twice as thick as traditional lights. The light includes three different replaceable lens (Flood, Spot, and Combo).

Features:

• Heavy Duty Design​
• IP69K Rating​
• Flood, Spot / Flood, & Spot Lens Included
• Stainless Steel Bracket & Hardware​
• 5,000k Light Color – Natural Daylight
• Heavy Duty, black, steel Left & Right mounting brackets to bolt directly to your lower triple clamp.
• Harness with Switch

Kit includes: 2x LED Aux lights with harness and switch, 2x Light mounting brackets and bolts, Switch mounting bracket

 This kit will work with the 6.6 Gallon Acerbis fuel tank for the DR650. You must run the light brackets inwards in order for there to be proper clearance with the 6.6. Gallon tank.

This kit includes 2 auxiliary light mount brackets. These brackets are designed to mount to most lower triple clamps. New longer bolts are supplied to accommodate the thickness of the bracket. These brackets are powder coated black for a sleek and long lasting finish. The brackets can be used to put the addition of new lights to the outside of your forks or swap the brackets and the lights can be mounted inward to give more clearance for bigger shrouds or fuel tanks.

The perfect solution for mounting those LED auxiliary lights. The base of the RAM mount is held by your mirror. This puts the light where you can easily adjust the angle for different riding situations. This mount fits VisionX Solstice lights or any other light with a 6mm or 1/4" hole in the mounting bracket.

This is for Mount Only. Sold individually.

10 Watt LED lights sold separately.

This frame includes six, white, full-spectrum LED bulbs on a 6-inch strip for bright illumination of your license plate. It is made in a sturdy cast aluminum, and is powder coated with a durable black finish.

Outside frame dimensions are 7.25" in. wide by 4.2". Center to center mounting hole distance is 5.7 in. All mounting hardware is included.

• Waterproof, long-lasting marker light bar uses less power
• Features 180° visibility
• White LED color
• Can be used in any position; refraction of light depends on position
• Measures 38mm x 9.8mm x 18mm
• Not for use where DOT lighting is required.

License plate light with 5 LEDs. Compact and easy to mount. Meets plate illumination requirements with super white light.

This is for the LED license plate light ONLY.

License plate bolt with bright white LED light. The simple way to light up your plate.