Used for DC conversions, this product allows a Trail Tech NiMH battery pack to mount to the vehicle.
Note: Not for use on bikes with electric starters.
The standard ring connector is a simple, quick connection with a fused positive ring cable and negative cable that attaches directly to your battery with an industry standard 2-pin, SAE connector.
The weather protected ring connector is a premium quick connect permanent battery lead with weather protected connection system and cable. It features 1/4"/M6 ringlets, 20" L, Industry standard 2-pin, heavy-duty SAE connector, 15A fuse, Cable max rating: 5 Amps, Cable remains flexible at below freezing temperatures; rated for -40°F/-40°C.
This bright and compact 6-LED flashlight plugs right into your SAE battery charging socket for hours of light. In addition, it has a charging system check that lets you know if your bike is charging properly. It features a 40 inch cord so you can see in those out of the way places when you need to.
Small 2 3/4" diameter motorcycle horn. Works on 12v DC. Sound will be diminished when running on AC.
Convert your AC headlight output to charge a 12 volt battery. Handles up to 150 watts. Must be connected to a battery to function properly.
This regulator/rectifier requires ungrounded inputs from the lighting coil. Many lighting coils are internally grounded and will require modification often referred to as 'floating the ground'. This simply means cutting the grounded end of the lighting coil wire, extending it and running the extended end out of the case along with the original 'live' end of the lighting coil wire.
Deltran quick-connect plug with LCD voltmeter display. Plug this into your Battery Tender, or any SAE cable, for an LCD display of the battery voltage. Three LED lights indicate the state of charge as well.
A digital voltmeter that can be mounted almost anywhere, on any bike, thanks to ProCycle's multi-position stainless steel bracket. Keeps you informed on the status of your charging system.
Completely waterproof and comes with connectors, wires and thorough instructions. A "must have" device for riders who use heated riding gear, heated grips, additional lighting, GPS, etc.
Headlight is DOT approved. Has both high and low beams. Attaches to the upper fork tubes with rubber straps. Turn signals are embedded in the headlight housing.
Integrated turn signals may require resistors to flash correctly.
So you say you want more light for your dual sport? Give this 7"DOT legal Rally light a try and light it up like a freight train! HIGH/LOW operation and SAE/DOT/E4 approved.
This light does not have the large Cyclops logos shown on one of the images.
Optional 10.0 Lumen LED High/Low Upgrade and now the Phoenix LED complete headlight for the ultimate DOT headlight
The stock lamp that comes with this rally light is great, but you can get well over double the brightness with the LED upgrade at a substantially lower power draw. Note if your bike is ac powered at the headlight you will need the rectifier for the LED option.. AKA carbureted KTM's CRFX and XR400/650.. others may apply.
10-Watt LED
The Solstice Solo LED Pod light outputs 1,052 raw lumens from a single 10-Watt LED and outshines most factory halogen headlights. Vision X uses top-binned LEDs, guaranteeing that you’ll have the most lumen output your dollar can buy.
Compact Form
All those raw lumens come out of a housing that is only 2″ wide. Featuring a singe-bolt mounting system, you’ll be able to take the Solstice Solo Prime anywhere, anytime.
The Solstice Solo also features a 4 sided channel design that allows you to interlink it on all four sides with other Solstice Solo pods. Includes stainless steel mounting bracket and waterproof connection. Choose narrow 10°, medium 30°, or wide 60° light beam pattern.
Sold each.
| Beam | 10° |
| Housing | Black |
| Raw Lumens | 1,052 lm |
| Effective Lumens | 736 lm |
| Weight | 0.76 lb |
| Input Volts | 9-48V |
| Watts | 10 |
| Amp Draw | 0.83A |
Available in two wattage configurations: 30 watts and 42 watts, which produce luminous outputs of 5000 lumens and 7000 lumens, respectively. If your motorcycle's electrical system cannot accommodate these wattages, the light can be operated in low beam mode, resulting in a 50% reduction in power consumption. When additional illumination is required, users can easily switch to high beam mode.
Despite its compact size, this LED light is designed to deliver substantial luminous output. Its performance surpasses that of other mini LED lights in the market.
The light is equipped with a durable push-button switch, metal handlebar mounts, and adaptable options that allow for compatibility with various motorcycle configurations. It features components such as switches, cords, strain reliefs, and optics that are engineered for enhanced water resistance, robustness, and overall performance.
Tailored specifically for snowbike applications, this light boasts a compact design with significant output capabilities. Enhanced heat is directed to the lens, facilitating snow melting and enabling continuous riding.
This light is ideal for users seeking a lightweight solution to comply with legal requirements for headlights while also being sufficiently powerful for racing and trail riding.
Installation is straightforward, with the light mounting easily to a number plate; however, the use of the recommended upgraded stainless steel platform mount is advised for improved convenience. The light operates using the motorcycle's battery power.
The Explorer light bar is equipped with a GoPro-compatible mount and an aluminum platform, allowing for versatile mounting options. A handlebar mount is provided for central positioning on the handlebars. (Fits all stock 7/8 and 1 1/8 bars. Not for flexbars) Notably, there are no plastic components in the light head assembly.
Included with the product is a rubber-covered switch that can be mounted on the handlebars, offering three power settings: off, 50%, and full brightness.
The light features a combo beam pattern, integrating spot, driving, and wide beam configurations into a single unit.
Now a lifetime warrantied LED light set at a budget friendly price.
The new Cyclops Pegasus led light set comes complete with a high quality relayed wire harness and a potent combo light beam pattern.
We are able to offer this fantastic light at a great price due to a one piece optic and sealed beam construction, eliminating extra parts and creating a very durable and high performance light.
These lights in white feature 7 watt emitters (28 watts per light) with two 10 degree and two 25 degree optics, Good for 500 plus ft of lighting (white).
The amber version is a Cree 3 watt emitters (12 watts per light).
This combo beam pattern offers good forward lighting and extremely good conspicuity.
The light set is available in white 5600K or a extremely bright Amber, perfect to allow those autos to see you. Lightweight and robust at 2.75 inches with a single stud mounting, they fit just about anywhere you would like to mount your lights.
Specs:
The Mojave Series LED Racing Lights have been designed to survive and operate in extreme conditions. Lights feature a heavy duty housing that can withstand hard impacts and a lens that is twice as thick as traditional lights. The light includes three different replaceable lens (Flood, Spot, and Combo).
Features:
This kit will work with the 6.6 Gallon Acerbis fuel tank for the DR650. You must run the light brackets inwards in order for there to be proper clearance with the 6.6. Gallon tank.
Kit includes:
This kit includes 2 auxiliary light mount brackets. These brackets are designed to mount to most lower triple clamps. New longer bolts are supplied to accommodate the thickness of the bracket. These brackets are powder coated black for a sleek and long lasting finish. The brackets can be used to put the addition of new lights to the outside of your forks or swap the brackets and the lights can be mounted inward to give more clearance for bigger shrouds or fuel tanks.
The perfect solution for mounting those LED auxiliary lights. The base of the RAM mount is held by your mirror. This puts the light where you can easily adjust the angle for different riding situations. This mount fits VisionX Solstice lights or any other light with a 6mm or 1/4" hole in the mounting bracket.
This is for Mount Only. Sold individually.
10 Watt LED lights sold separately.
This frame includes six, white, full-spectrum LED bulbs on a 6-inch strip for bright illumination of your license plate. It is made in a sturdy cast aluminum, and is powder coated with a durable black finish.
Outside frame dimensions are 7.25" in. wide by 4.2". Center to center mounting hole distance is 5.7 in. All mounting hardware is included.
These super bright, white LED lights come with a clear or black housing and include studs and hardware to facilitate an easy installation.
Measures 1-3/4 in.W x 3/8 in.H x 3/4 in.D
License plate bolt with bright white LED light. The simple way to light up your plate.
Clear lens, amber LED type lights. Short flexible stems. Very small, only 2 7/8" long. Requires a LED turn signal flasher to flash properly. 4 Pack
Eight ultra-bright amber LED lights in a sleek design. Flexible stem helps absorb the occasional hit. Available in 2 pack or 4 pack
Recommended to use resistor for proper turn signal flash rate.
Specifications
These Sequential Turn Signals are available in a 2 pack or 4 pack flexible stem with 7 LEDs on the front models and 14 LEDs on the rear model.
Matte Black, plastic body with smoke lens and 8mm mount bolt.
Specifications
Easily turn your blinkers into additional running lights and brake lights (rear) for added visibility.
White light in the front and red in the rear. Rear red running lights and bright red brake lights. You can omit the running and brake lights if you wish and still have the best blinkers on the market.
Dazzling bright Amber blinker functions.
Everything comes in a spring-loaded stock designed to keep it safe from those unexpected tip-overs, crashes, or encounters with brush and trees. They’re flexible enough to bend 360 degrees, yet tough, durable, and almost impossible to break!
If you have a single indicator light for the blinkers that is not built into the display and is not LED you will need the diode kit (AKA DR650) If it is built into the speedo display it should not require the diode kit.
Available in a generic kit with Bullet connectors supplied. Great for your DR or almost any other bike with a single post blinker setup. These will work well on bikes that use a flasher, but you might have to add the female side of the connectors that are included in the kit.
Not for Yamaha T7, see model specific listing
These signals have short rubberized flexible stems and bright mini halogen bulbs.
The Barkbuster LED Indicator Lights for Jet, Storm & VPS Plastic Handguards to increase your visibility and safety using 15 high intensity LEDs that mount directly to the plastic handguard shells. Super bright auxiliary signals will make your directional intentions clear to upcoming traffic. The LED indicators are very low draw and E marked for road use.
Features:
What's in the box:
Please Note: Not compatible with the electrical system on the Honda Africa Twin CRF1000L
Ultra bright amber LED turnsignals offer nearly the same visibility as OEM in a much smaller package. 15 amber LEDs in every signal. Flexible rubber stalks. Requires a LED turn signal to flash properly.
Pack of Two
These Sequential Turn Signals are available in a 2 pack or 4 pack short stem with 7 LEDs.
Matte Black, plastic body with smoke lens and 8mm mount bolt.
Specifications
Triangle/Teardrop style signals with LEDs. Mounts on any flat surface to keep out of the way of brush, branches, and your exhaust system. Requires LED flasher or LED turn signal resistors to flash properly.
This Diode Kit is only necessary if you have a single dash indicator for your turn signals. One dash light for both left and right signals (such as on the DR650).
This kit allows power to flow in just one direction from the LED signals to the dash indicator light regardless of which direction you are signalling.
You may have noticed after installing aftermarket LED turn signals that your blink rate has significantly increased. OEM flashers are designed for standard bulbs which draw a few watts each, much more than typical aftermarket bulbs or LED signals. This device is an effective alternative to using load resistors because it consumes considerably less watts, consumes less space, and does not generate excessive heat.
The plug is exactly the same as the OEM unit making swap outs a cinch. No wiring changes, cutting and adding connectors. Just plug it in and you will have a steady flash at the DOT OEM flash rate when aftermarket LED turn signals are installed. It is an all solid state design and will blink correctly with loads all the way down to 0.1W / 0.01A.
Not for any DRZ400 or Royal Enfield Himalayan
Not for use with stock bulbs.
This type of flasher is required for LED turn signals. For DC (battery) systems only. Includes 2 female connectors for universal fit.
Not compatible with any DRZ400
Heavy duty 12 V flasher works on AC and DC lighting systems
Not compatible with any DRZ400
Allows LED type turn signals (and low wattage flush mounts) to flash using a standard flasher unit. Connectors included. One kit works with 4 signals.
The Barkbusters 10 OHM Resistor Set for LED Indicator Lights will correct the flash rate of your auxiliary signal lights. Ready to plug in connectors make installation a breeze. These resistors are intended for Barkbusters LED Indicator Lights.
Features:
This devices allows any two wire after market LED turn signal indicators to operate as running lights (always on), and will blink on / off when the turn signal switch is activated. It is highly recommended to use this product with the Fixed Rate Turn Signal Flasher. This device, as well as aftermarket turn signals, use much less current than stock turn signals, thus an increased flash rate will occur. Load resistors or a fixed rate turn signal flasher will get your flashers operating at the normal flash rate again.
Each package contains two separate adapter boxes, good for operating both turn signals, left and right of either the front OR rear of your motorcycle. You will need to purchase a 2nd kit if doing the Front AND Rear of the motorcycle.
This device is universal; designed to work for any motorcycle with a DC electrical system. Kit comes with bullet connectors to wire in manually. Works with any two wire non-sequential aftermarket LED turn signal indicators.
Fits Most Models
These turn signal relocation brackets from ProMoto Billet provide an easy way to move the stock turn signal lights, useful if you find them getting in the way of your luggage configuration.
These brackets may utilize an existing hole in some of the rack side brackets, though many applications will require drilling or fabricating in order to mount properly.
Replacement Halogen bulbs for mini style turn signals. Sold in a pack of 5 bulbs.
Roll-up pouch ideal for tucking away your lights when out on the trail.
Taillight and brake light Attaches to the top of the rear fender. Dimensions: 3 1/2" wide x 2" long x 3/4" tall. D.O.T. approved.
LED powered taillight, brake light, license plate light & license plate mount. Attaches to the underside of MX style rear fenders.
Taillight, brake light, & license plate holder (no plate light). Attaches to the underside of MX style rear fenders. Small and good looking!
Taillight, brake light, & license plate light. Attaches to the top side of enduro style (XR, KDX, etc) rear fenders. Dimensions: 2 3/4" x 4 3/4" x 2 1/2" tall. Wiring instructions included.
Taillight, brakelight, turnsignals, license plate light & license plate mount. Taillight is DOT approved, turn signals are not. Attaches to the underside of MX Style rear fenders. Turnsignals are embedded in the taillight housing. Wiring instructions included.
*Flushmount signals may require resistors to flash correctly
Installing new turn signals or brake lights and need to find the 'HOT' wire, or are you just trying to find out if a specific wire has power going to it? Either way, this test light can help you locate shorts, open, and voltage on 12-24 volt DC circuits.
Has both high and low beams. Attaches to the upper fork tubes with rubber straps. DOT and CE approved.
Inexpensive way of getting the factory look. Adds 1/2" of width to any standard foot peg. These will give you a much more stable platform when standing on the pegs.
Sold in pairs.
Not your average rubber insert! These rubber covers go over the top of your MK3 or MK4 Pivot Pegz so that the aggressive teeth are only exposed when you need them in muddy conditions.
Important to verify which style Pivot Pegz you have before ordering.
Like most machines, the OEM pegs on the Africa Twin are for the birds. They are small and provide a minimalist platform to control the motorcycle and they are uncomfortable if you stand on them for very long. You can install new, larger pegs or you can bolt on these beautiful aluminum extenders on top of the stock units. You can see the stock peg inside the topper in the upper image.
If you stand for very long these pegs will pay for themselves quickly. CNC machined with slightly rounded edges on the teeth so they won't eat up the soles of your boots, then anodized black, these are pretty and functional. 2.32" x 3.38" is nearly double the contact area of the stock pegs. Mounting hardware and detailed instructions are included, making installation a snap.
The IMS Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping.
They are the original Cast 17-4 Stainless steel pegs that revolutionized the foot peg market.
These pegs are 50mm(1.95") x 78mm(3.1").
Pivot Pegz have set a new standard in footpeg performance and quality and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty.
Pivot Pegz aim is to build the best footpegs in the world and they really do perform as good as they look. Here's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever.
Services two Pivot Pegz and fits MK2, MK3 and MK4 Pivot Pegz
Kit Contents:
High Quality chain. Will need to be cut to fit your sprocket combination.
Comes with screw-type master link
Always carry a spare master link when out on the trail.
Master links are not interchangeable. Be sure to check the manufacturer and series on your chain.
These do not fit the TW200 or XT250. Only for 520 or 525 chains, Please verify chain size.
Replace these any time you feel excessive play in the sprocket hub.
Excessively worn dampers can cause the cush hub bearing to fail - which will ruin your sprocket carrier.
Sold as a full set.
These quality sprockets are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.
These quality JT sprockets are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.
Designed for quick and accurate alignment, this tool clamps squarely to the rear sprocket so the alignment rod can indicate sprocket alignment with the chain.
Here is a tool to help you remove a few links from a chain that is too long. A great tool to have in your tool box.
The head of the pivot pin you are going to remove must be ground down level with the side plate before using this tool to push it out. Failure to do that will cause damage to the tool that is not covered by any warranty!
Can break or rivet chains from #35 to #530 like a pro.
kit includes a 2mm, 3mm, and a 4mm pin to fit most chains.
kit includes press plates,and all necessary riveting pieces and comes in a durable plastic case.
NOTE: when breaking a chain, YOU MUST grind the heads off of both pins on a link first.
This is without doubt the fastest, most effective, most meticulous, precise and systematic method for giving your chain a thorough cleaning. It forces its bristles between the plates where dried and hardened chain lube, road sand, glass, tar and other materials gather to form a hard shield of abrasive dirt where the O-ring meets the chain plates.
Note: Designed to be used with the engine off
Innovative design that cleans chain from 3 angles at once. Long handle keeps fingers and hands away from chain and sprockets.
Introducing Oinker®, the revolutionary chain lube attachment for dirt bikes, street bikes, and ATVs. Say goodbye to messy lubrication. Oinker® attaches to any chain lube or wax, ensuring a precise and even application to both sides of your chain. This means minimal overspray, keeping your swing arm, rear tire, and brakes clean.
*For cans with an attached smart straw, you will need to replace it with the included nozzle
What's Included:
Make your life a little easier by having a set of these in your toolbox. Designed to simplify installation and removal of clip-type master links. One tip is shorter and notched to be placed on the pin which allows the longer end to push the clip.
This Motion Pro press tool is a must have when installing and removing Clip-Style master links (520, 525 & 530 sizes).
Easily presses on and off master link plates, works on 520, 525 & 530 Clip-Style master links.
Maximum master link width 24.8mm.
Will not damage master links, hardened steel pins for reliable use.
Light weight billet aluminum construction.
A high quality master link press tool from Wirth Machine used for the removal and installation of master links using a press fit link plate.
Fits 520, 525, and 530 pitch chain.
ULTIMATE SPROCKET WRENCH KIT
The ABUS SmartX 8078 3D Alarm Disc Lock offers advanced Level 18 security, combining cutting-edge technology with exceptional protection for your bike.
Featuring a 13.5mm double-locking sliding bolt made from specially tempered hardened steel, it delivers superior resistance to tampering.
The 3D motion-sensing alarm emits a powerful 100dB sound to deter unauthorized movement, while the SmartX Bluetooth keyless lock system provides ultimate convenience. It seamlessly connects to the ABUS SmartX App, allowing you to monitor lock, alarm and battery status in real-time.
The USB-C rechargeable battery ensures long-lasting performance and multi-color LED lights with audible signals keep you informed. The lock also features location memory from the last pairing, providing added peace of mind.
Double-H sintered metal brake pads feature the HH friction rating, the highest in the industry. These pads provide maximum brake effect and last twice as long as organic pads.
Set includes pads for both front calipers.
These DP Standard brake pads are our OEM replacement sintered metal compound. Ideal for everyday use, both on and off-road. They provide excellent all-round braking hot or cold, wet or dry. Where applicable a high-tech ceramic heat shield is applied to the rear of each backplate to reduce the heat transfer into the fluid and prevent brake fade. They have one of the lowest wear rates on the market, very low levels of brake dust and no noise and no thermal cycle bedding-in required are also benefits of the DP Standard brake pads.
This brake bleeder makes bleeding your brakes a one man job.
The unique check valve allows fluid and air to escape while preventing air from re-entering the system.
Combines wrench and bleeder valve into one convenient and compact tool
The progressive factory springs are well known to be way to soft for most riders. Cogent Dynamics straight rate springs will give better control in the rough stuff and when loaded up.
Sold in pairs.
0.72kg/mm riders up to 260lbs
0.80kg/mm riders 260lbs and up
The 0.72 springs are 28% stiffer than stock and will be a great choice for most riders
Not compatible with Adventure Sport ES
Save time and money with this complete OEM quality fork bushing kit.
Complete kit to replace the bearings and seals in your shock linkage. Includes the lower shock bearing.
| Kit Contents: | |
|---|---|
| Ball Bearing | 1 |
| Bushing | 1 |
| Needle Bearing | 2 |
| Needle Bearing Shaft | 2 |
| Seal | 4 |
Link lowers the rear of the bike by 7/8".
Comfortable at a stop or on technical trails.
Installation takes about one hour, and only a few minutes more to drop the forks in the front to match.
Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.
Based on the wildly popular Race Tech Suspension Seminars taught by Paul Thede around the world, this step-by-step guide shows riders how to make their bikes handle like the pros. Thede gives the lowdown on all types of suspension, including cartridge and non-cartridge forks as well as dual-chamber and nitrogen-charged shocks.
The three forces of suspension, testing procedures, even the black arts of chassis geometry: This explains it all. The book provides step-by-step photos of suspension disassembly and assembly as well as a detailed troubleshooting guide for dirt, street and track.
Showa removed the schrader valve on many newer rear shocks. Now you need a needle to recharge your shock with nitrogen after a rebuild. Race Tech built this unit just for that job.
The features of this tool include 300 psi capacity, bleeder valve and T-handle plunger pin chuck. Swivel chuck has a 12" flexible hose. Comes complete with instructions, carrying box and Schrader valve extension (required on some Showa shocks). Nitrogen bottles available at any welding supply house.
This Quiet Insert comes stock in all new FMF Q4 mufflers. If you lost yours, this is the replacement you need.
It will fit Q4, Q4 Hex, Powercore and Powercore Hex mufflers.
It will reduce the sound rating of the Power Core models, from about 99db down to about 96db.
Please choose the correct Insert for your muffler. If you are unsure of the year that your muffler was manufactured you can easily identify visually which insert you will need.
| Pre '21 | Installs using one small screw |
| '21-Cur | Installs using a spiral retaining ring |
This gasket seals the joint between the head pipe and Exhaust port. These gaskets are designed to crush a little bit to tightly seal where the pipe fits to the head. Get a fresh one now avoid having an exhaust leak when you install your new exhaust.
Kit includes two gaskets.
This gasket seals the joint between the head pipe and muffler. These gaskets are easily damaged when removing the original muffler. Get a fresh one now to ease installation of your new performance muffler.
Protect your head pipe from rock damage. This stainless steel spine clamps to your head pipe to add a layer of protective armor between your vulnerable pipe and those nasty rocks or logs. Fits the stock headpipe. Will fit the FMF head pipe with the addition of larger clamps.
