Off-road only version of the DR350
Sold in the US 1990-1999
Chain Size: | Front Sprocket: | Rear Sprocket: | Front Tire: | Rear Tire: | Spark Plug: |
520x110 |
14T ('90-'93, '97) 15T ('94-'99) |
47T ('90-'93, '97) 44T ('94-'99) |
80/100-21 | 110/100-18 |
DPR9EA-9 ('90-'93, '97) CR9EK ('94-'99) |
Featured Products
It may not surprise you that they are covered with HippoSkin™, their waterproof outer shell, and insulated with a generous layer of HippoFat™, a warm, flexible, closed cell foam insulation—both are designed to keep inclement weather away from your hands.
Sold in pairs.
Hand/brush guards are required for proper fitment and for safety reasons.
Hippo Hands go on and off in seconds and never require tools or hardware.
The Backcountry is 9" deep.
If you like to stand and ride, this is the model for you! But… these hand covers also fit to just about any bike. They are also a great option for cruisers with hand guards or lever guards.
They feature a durable, quilted interior and flexible, neoprene cuff which ensures a great fit on so many bikes. The Backcountry is their smallest, most easily adaptable hand cover.
The Backcountry features a front reflective panel for higher visibility in low light situations.
Engine
K&L® shims exceed the maximum of the Apparent Rockwell Hardness "C" scale. Shims average 47.0 compared to the 46.0 maximum.
These kits fit multiple brands and models, please verify correct size for your model before purchase.
13mm diameter - Includes two valve shims of each size 2.30, 2.40, 2.50, 2.55, 2.60, 2.70, 2.80, 2.90, 3.00 and 3.10. In a shim box.
20 shims in total. From K&L.
KAWASAKI
K&L® shims exceed the maximum of the Apparent Rockwell Hardness "C" scale. Shims average 47.0 compared to the 46.0 maximum.
This kit fits KLR650 87-18 as well as other brands and models , please verify correct size for your model before purchase.
29mm diameter - Includes two valve shims of each size 2.30, 2.40, 2.50, 2.55, 2.60, 2.70, 2.80, 2.90, 3.00 and 3.10. In a shim box.
20 shims in total. From K&L.
BMW / KAWASAKI / YAMAHA
Providing unbeatable performance and exceptional value, Hiflofiltro is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide. The filters are also supplied to original equipment manufacturers as well as private label brands.
You pay $3.40 per filter with our value 10-pack!
GoldPlug is the gold standard in engine protection.
Stainless steel drain plug with an extremely strong magnet that picks up metal flakes in your oil.
12mm Thread
Keep your motor running right with a fresh plug.
A Dual Electrode spark plug will last longer than a single electrode plug because the wear is shared between the electrodes.
Iridium spark plugs are made with premium quality materials.
Iridium plugs last longer than standard ones, meaning you won't have to replace them as often.
- The ultimate in the evolution of spark plug technology and performance from an industry leader
- The iridium electrode is 25% smaller than a platinum electrode, and it's just 1/4 the size of a conventional nickel electrode
- Ultra-small diameter center electrode reduces voltage requirement and extends ignition system life
- Metal shell plating has enhanced anti corrosion qualities
Sold individually, unless otherwise stated.
Keep your motor running right with fresh spark plugs!
NGK is one of the world's largest manufacturer of spark plugs, whose products are used as original equipment (OE) on countless motorcycle and automobile models.
- High-quality materials and superior construction for serious power and reliability
- Pure alumina silicate ceramic insulator provides high strength and better heat transfer
- Deep-seated copper core for a wider heat range
- Nickel alloy tip for longer life
- Trivalent metal plating provides superior anti-corrosion and anti-seizing properties
- Choosing the right high-quality plugs prevents fouling from running too cool and preignition from running too hot
- NGK plugs available for almost every application and riding style
Clymer manuals are the most user-friendly repair manuals. They are written for the do-it-yourself-er as well as the experienced mechanic by industry experts. Step-by-step instructions based on the complete disassembly of the machine. This manual in written to cover 90-94 models but nearly all of the information will apply to newer models also.
This tool is designed to separate vertically split crank case halves on two and four stroke engines. Adjustable arms allow it to be used on multiple bolt patterns found on a variety of makes and models of motorcycles. Industrial grade steel construction with black oxide finish for long service life. Comes with 8mm mounting bolts and 6mm adapters. Protective carrying case included.
Thread Chasers are designed to clean and re-cut damaged aluminum threads.
This kit contains the two sizes most common on metric motorcycles, M6x1.0 and M8x1.25.
Thread Chasers also remove dirt and metal shavings that become captured in thread grooves.
Uses 8mm or 10mm hex sockets, a Must for all tool kits.
A 'wrench style' tool to turn the 'square top' tappet screws. The wrench does a better job of holding the adjuster screw still while tightening the locknut. Slim and flat, this tool is easy to carry in a tool pack.
- Allows precise valve lash adjustment without disturbing the setting when the lock nut is fastened
- Knurled knob on adjuster drivers ensure a precise and secure grip
- Integrated repositionable wrench handle holds the lock nut while the drivers are used to loosen or tighten the valve adjustment screw
Set includes:
- (1) 10mm steel socket wrench
- (1) 3mm square tappet adjuster
Fuel and Intake
Twin Air Filter's patented design, high quality materials and superior construction deliver unbeatable performance and protection - and make Twin Air Filters the hands-down choice of more World and National Champions than all other filters combined.
An air filter is your engine's only protection against the elements, and your stock filter isn't up to the task. Replace it with a Twin Air- the number 1 filter system proven on motocross tracks around the world.
Twin Air's fused layers of open-pore foam and fine inner foam trap even the smallest particles-without restricting airflow
Sold in 6 packs
- Compatible with many air filter boxes. Easy to install by drilling 1’’ holes in airbox housing and snap fitting vents in.
- May be cleaned and re-oiled
- More air flow allows you to add more fuel to your intake mixture, increasing performance.
- 1" Diameter
Not legal for use on pollution controlled vehicles in the state of California.
Gas Tanks
TechSpec’s Motorcycle Tank Grips were developed to improve body, bike control and increase riders comfort. Gripping your motorcycle between your knees or thighs improves overall control of your ride by better securing your body weight and seat position under the forces of braking, cornering and acceleration while also relieving pressure from your wrists, elbows, shoulders and lower back giving you increased control and a more comfortable, safer ride. Snake Skin is a thin, .125” medium durometer “rubber” material that offers a secure, comfortable grip, durable protection and a clean stock look.
This universal precut kit includes left and right tank grips. (8" X 3") Triangle
If you're like us, you hate the long floppy vent hose hanging off the cap of your aftermarket tank.
This one-way vent cap replaces the long hose with a short one only about 2" long. It allows air into your tank but prevents fuel from sloshing out.
Machined from billet alloy and anodized for good looks.
Not for stock fuel tanks!
Security for your fuel tank. Includes 2 keys. Internally vented with a check valve that prevents spillage in case of a tip over.
Fits Acerbis, IMS and Safari tanks only.
This CNC cap will replace the stock gas cap on the stock tank. You do need some parts from the stock cap, so don't throw it away yet! It is not difficult and this kit includes the additional hardware required. Also included is a vent tube with a matching cap.
For use on STOCK TANK ONLY! This is NOT a locking cap.
Does not fit California model DR650
Does your stock vacuum operated petcock not shut off when your bike is parked? Replace your stock vacuum operated petcock with this manual one. Must be shut off any time the bike is parked for more than a few hours. Fits stock or aftermarket tanks. Plastic tanks may need the hole 'ovalized' to fit the dual standpipes.
Does not fit OEM XR650L metal tank
A popular upgrade from the stock vacuum operated fuel valve. Manually operated. Must be shut off any time the bike is parked for more than a few hours. Fits stock tank or aftermarket tank and has both main and reserve. Fully rebuildable.
Fuel supplies can be sketchy at times. This filter lives in your tank to trap dirt and debris as it is poured into the tank. Features a custom shaped adapter that fits securely under the gas cap, creating a leak-proof seal. If it stays out of your fuel, it can't get into the carburetor! Created by the filter experts at Twin Air, this filter fits IMS, Acerbis and Safari brand gas tanks.
Hose reducer to go from 5/16" line down to 1/4" line. Many bikes have 5/16" carburetor spigots but most aftermarket petcocks are 1/4". This solve the problem of mismatched sizes. Solid brass construction. Can be used to route or repair fuel lines, oil lines or air lines. Barbed ends provide a secure fit.
All of these lines are stronger and more durable than vinyl fuel lines and are resistant to swelling, UV light, as well as hardening and cracking.
Five-layer Greenshield® Barrier Technology cuts vapor loss and saves fuel, making it safe for the environment and fuel efficient.
1. Barrier tube - provides high heat and corrosive liquid resistance.
2. Greenshield® barrier - patent-pending technology provides the lowest permeation in the industry.
3. Adhesion layer - secondary protective barrier.
4. Reinforcement layer - spiral textile reinforcement provide strength and pressure resistance.
5. Cover - protect underlying components.
- 30" length, 1/4" ID
- Temperature Range: -40°C to +125°C (-40°F to +257°F).
- HNBR tube with thermoplastic barrier and CPE cover; reinforced aramid fiber.
- Oil, heat, ozone, and abrasion-resistant cover.
- Multi-fuel compatibility. Unleaded gasoline, methanol, ethanol (E10, E15, E85)
- PSI rating: 35 to 50.
- Not for use with fuel-injected models
All of these lines are stronger and more durable than vinyl fuel lines and are resistant to swelling, UV light, as well as hardening and cracking.
Five-layer Greenshield® Barrier Technology cuts vapor loss and saves fuel, making it safe for the environment and fuel efficient.
1. Barrier tube - provides high heat and corrosive liquid resistance.
2. Greenshield® barrier - patent-pending technology provides the lowest permeation in the industry.
3. Adhesion layer - secondary protective barrier.
4. Reinforcement layer - spiral textile reinforcement provide strength and pressure resistance.
5. Cover - protect underlying components.
- 30" length, 5/16" ID
- Temperature Range: -40°C to +125°C (-40°F to +257°F).
- HNBR tube with thermoplastic barrier and CPE cover; reinforced aramid fiber.
- Oil, heat, ozone, and abrasion-resistant cover.
- Multi-fuel compatibility. Unleaded gasoline, methanol, ethanol (E10, E15, E85)
- PSI rating: 35 to 50.
- Not for use with fuel-injected models
RotoPax are Rotational Molded - the process which produces indisputably superior products.
- Thicker walls and stronger construction
- Bright colors that are less prone to fading
- Extra threads, thicker walls, and sure-seal gasket guarantee no leaks
Need to mount two containers? A water and a fuel? Two waters? Finally, you can stack multiple packs together! Use in conjunction with a pack mount. You will need to purchase the Single Mount as well as the Extender.
Auxiliary fuel tanks mount to handlebars, forks, or rear racks.
- Suitable for minis, trials bikes, full size bikes, and anywhere else a little extra fuel is needed.
- Each tank includes a siphon kit that connects the tank to the main fuel tank and automatically siphons fuel while the bike is being ridden.
- With this design, the auxiliary tank empties first, before the main tank.
- Does not interfere with headlight, handguards, rear seat, etc.
This Super Siphon has a (1/2 inch x 6 foot) long hose, which makes it quite easy to transfer fuel from one bike to another! Simply, shake the hose to prime it and get fuel moving. The hose is resistant to gasoline and any other hazardous chemicals. Roll it up, stuff it in your bag and you will be very happy whenever you need it.
Increases fuel capacity for longer range than stock.
Capacity: 4.2 gallons or 15.9 liters
Uses stock mounts and petcock. Cap furnished
ONLY ONE AVAILABLE IN WHITE. New in original packaging with hardware. Sale will be final, no returns or exchange available.
Offroad Models only
Body
Puig Visor Clip-On
- Suitable for screens with thickness between 3-5mm
- Multi-adjustable visor adaptable to Puig and OEM windscreens
- Visor is mounted by clip-ons and does not need to be drilled to the windscreen
- Visor sizes available include 90x230mm, 100x277mm and 102x325mm
Front fender from ProCycle Plastics (formerly DSA) is shaped very much like the OEM DRZ400SM front fender. Big enough to be functional without wind-steering the bike like the stock fender does. Vacuum molded, these are a design improvement over stock. These are fully compatible in any combination with the original factory plastic.
This frame includes six, white, full-spectrum LED bulbs on a 6-inch strip for bright illumination of your license plate. It is made in a sturdy cast aluminum, and is powder coated with a durable black finish.
Outside frame dimensions are 7.25" in. wide by 4.2". Center to center mounting hole distance is 5.7 in. All mounting hardware is included.
A stainless steel front fender brace. Helps stabilize your front fender.
Gives additional strength for carrying a fender mounted tool bag.
Fits on top of the fender and bolts between the fender and bottom triple clamp. Stainless steel won't rust or corrode. Includes hardware.
Requires you to drill one hole in the fender for mounting.
B&B Off Road Engineering Fender Brace is made to help support your front fender/guard. Also helps support and reduce fatigue from constant vibration.
Made from 4mm 5083 structural aluminum plate. If you wanted to carry a small tool bag this would be a perfect product to support the weight and strap the bag to.
Fits on top of the fender and bolts between the fender and bottom triple clamp. Requires you to drill one hole in the fender for mounting.
Seats
Corbin seats are custom made to order. You can choose your preferred texture for the top and sides of the seat.
Precision fit to the tank and side panels, Corbin's Dual Sport saddle works with aftermarket tanks too! 1 1/4 inches lower to make for an easier reach to the ground. High density infinite ratio space foam allows us to lower the saddle while maintaining a resilient comfortable ride. Unique contoured shape, combined with high quality space foam provides long range comfort on Dual Sport machines.
Can be color coordinated with a wide range of color options to customize the look of your DR.
Installation: Mounts with the two "L" brackets transferred from your stock seat.
The default vinyl choices are black 'carbon fiber' on top and 'asphalt' on the sides, 'no welts', black logo. You can view all of the available materials and colors through the link below. If you would like your seat built with something other than the standard choices please state specifics in the comments during check out.
Please allow 3 weeks
Cannot be canceled
Seat Concepts dual-sport/adventure seat-kits incorporate a wider seating area for the rider, which results in more even weight distribution, while reducing pressure points. Each individual seat model has been specially designed to increase comfort without compromising ride-ability. The more aggressive the bike, the more aggressive the seat-kit.
Each kit contains detailed instructions for easy "Do It Yourself" installation. This provides the highest level of quality & comfort at an affordable price.
Available as a Foam and Cover Kit for OEM pan. It DOES NOT include the pan.
Width: 9 1/4"
Height: Same as OEM
Note:
This seat is based on the off-road version of this bike. The street version is 1 inch lower than this seat.
Note: Will NOT fit DRZ 250
This is the secret for being able to put in those 500 mile days. Even a good touring seat can feel a bit firm after a couple hundred miles. Sheepskin gives that little bit of 'cush' and provides superior air circulation. Velcro straps allow easy removal when you don't need it. Measures 14" wide by 19" long.
- Air filled AirHawk 12"x18" cushion custom fits your shape and redistributes pressure that causes numbness and discomfort when you ride
- Seat cushion cover is constructed of a breathable, stretchable Nylon/Lycra blend with a non skid Urethane base
- Open mesh side panels allow heat to escape
- Easily inflates by mouth with no pump needed
- Mounting straps and Repair patch kit included
9" by 9" carbon fiber seat warmer that goes between your seat cover and the foam to keep your backside happy on those really cold days. This improved design produces 25% more heat than most other warmers using just 30 watts.
Kit includes the warming unit, with connector, 24" extension cable, rocker-type on/off switch and stub to splice into your wiring along with complete detailed instructions.
CRF450L '19 - '24 CRF450X '19 - '24
This seat is black 'carbon fiber' on top and 'asphalt' on the sides, with red welts, exactly as shown. Slight discrepancies with cover under seat, and slightly off center foam thickness, indicated in pictures. As is, no warranty.
Corbin seats are carefully designed to provide a comfortable riding position. They are firm and supportive which allows you to ride all day without fatigue unlike the stock seat.
Armor - Bike Protection
- Protect vital engine parts and cases from rocks and debris
- Clear anodized for corrosion protection and good looks
- Skid plates made from 3/16" 5052 H-32 aluminum
- Smooth underside won't snag when crossing logs
- Oil drain hole
- Heat-treated chromoly steel clamps keep plates mounted securely
- All mounting hardware included
bash plate is made from 4mm aluminium 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider.
All bash plates are supplied with the necessary stainless clamps and bolts where possible. All bash plates have a polished finish and have foam or rubber where required.
Protect your frame/paint from scuffs and scratches with frame guards. The DR 250 & DR 350 frame guards are made from 2mm 5052 marine grade alloy and CNC machined in one piece for strength. All frame guards are supplied with all necessary mountings and stainless bolts. With a polished finish they look great and are easy to install.
Made of military aircraft grade 3/16" cast acrylic, this guard will protect your lens from roost, rocks and branches. Optical clarity of the acrylic ensures brightness and projection of your headlight are minimally effected while all the while protecting your headlight from impact and abrasion.
Guards are held to the headlight lens with an industrial strength hook and loop system on each corner.
Don't cut the ball ends off of your levers! These billet spacers move your hand guards outward to allow clearance for the full length of the stock levers. Designed to fit steel or aluminum bars. Includes longer stainless steel mounting bolts.
Developed for the DR650 but may work on other models with long levers. (May require additional adjustment or modification on some models.)
Not compatible with Acerbis and Emgo hand guards
Contoured alloy hand guards with inner mounts, allow space for the clutch cable and brake hose.
Images show a set of these hand guards installed on a set of CR High Gunmetal Fly Handlebars with large black deflectors. The far right image shows the need to flip the brackets that attach to the bar on the clutch and front brake side. On the front brake side the clamp must go over the front brake line while on the clutch side it goes under the cable.
Note: This kit includes the handguards only. Deflectors sold separate, can be added by selecting color from drop down menu.
For DR650 or other models with long levers add the optional universal fit Spacer Kit so you don't have to cut the balls off the end of your levers when installing these handguards. (May require additional adjustment or modification on some models.)
- High-impact, composite injection-molded outer guard around an anodized aluminum inner guard
- Includes an indexed steel bar-end insert that mounts solidly and prevents Rally Pro handguards from slipping – even under the most demanding conditions
- Small integral spoiler incorporated into design
- X-Strong universal silver mount kit that fits 7/8” (22mm), Pro Taper 1 1/8"(28mm), Magura and Twin Wall aluminum handlebars included.
Some models with adjustable windscreens may need the windscreen rotated forward, such as the Royal Enfield Himalayan, to avoid contact at full lock. These are not compatible on Honda CB500X's and Honda Africa Twins.
These handguards come with mounts that will work on both standard and and oversize bars. The aluminum wrap-around bar is the biggest on the market with two large plastic shields that are also some of the largest available. The X-Factor hand guards offer great protection from the elements, especially during those colder months when you're trying to stretch out your riding season.
Works with 7/8" or 1-1/8" bars.
X-Factor guards may require you to cut your lever ends down, or use short levers.
The X-Factory Handguards from Acerbis feature a steel bar wrapped with an injection molded Nylon composite. A replaceable dual injected polypropylene shield mounts to the bar offering insurmountable protection from roost, debris, and extreme conditions.
A universal mount kit is included that allows for mounting on either 7/8" or 1 1/8" handlebars.
Will not fit XT250 with stock handlebars (oversize bars ok). Recommend Acerbis Rally Pro X-Strong to clear master cylinder.
- Designed to minimize handlebar vibration for Barkbuster Handguards that can’t accomodate OEM handlebar weights.
- Sleek aerodynamic look.
- Forged Steel with powder coat finish.
- Fit in conjunction with most Barkbusters backbones (except EGO).
- Fits externally to the VPS backbone.
- Available in black.
- Sold as a pair
Weight:
360 grams/pair or
180 grams/each
Fitment Notes: If you have a hardware kit listed below see special fitting notes as additional parts may be required
BHG-010 Requires two additional M6x40mm countersunk bolts
BHG-032 R1200GS/A requires two additional M8x55mm countersunk bolts
BHG-045 G650GS requires two additional M6x65mm countersunk bolts
BHG-050 Will not fit
BHG-051 Requires two additional M6x50mm countersunk bolts
BHG-059 Tiger XC, XCA & XCX (all ’15 on) use M6x45mm bolt from BHG-059 kit
BHG-075 Will not fit
BHG-079 Will not fit
Protect your hands and levers with the Barkbusters Storm lever and weather protection handguards. Full wrap solid heat treated aluminum bars with secure two point mounts on each side provide strength while attractive and generous guards provide shelter from the wind and weather. Ride longer with the Storm handguards and complete mounting kit by Barkbusters.
Features:
- Two mounting points provide secure protection
- Full wrap guards
- Heat treated aluminum backbone bars
- Easy installation
- Tough and weather shielding Storm handguards
- Aluminum backbones are compatible with all Barkbusters deflector guards
What's in the box:
- Left and right aluminum backbone bars
- Inner and outer handlebar mounting hardware for both sides
- Left and right Storm plastic handguard deflectors
- Installation instructions
Not recommended for Africa Twin, T7, Himalayan, or V-Strom. Please see specific listings for those models.
NOTE: tapered kit will not fit Renthal Twin Wall or Barkbusters VSBar
Keep your hands and controls protected from the wind and impact with Barkbusters VPS lever and wind protection handguards. Heat treated aluminum backbones with two mounting points of these handguards provide the strength needed to prevent a tip-over from ending your motorcycle ride. Impact resistant deflectors, available in multiple colors, provide protection for your hands from the wind and brush. Ride longer, more comfortably with Barkbusters VPS lever and wind protection handguards
Features:
- Two mounting points provide secure protection
- Full wrap guards
- Heat treated aluminum backbone bars
- Includes VPS left and right plastic deflectors
- Easy installation
What's in the box:
- Left and right aluminum backbone bars
- Inner and outer handlebar mounting hardware for both sides
- Left and right VPS plastic deflectors
- VPS deflector fastening hardware
- Left and right adjustable position wind extension deflectors
- Installation instructions
Not recommended for Africa Twin, T7, Himalayan, or V-Strom. Please see specific listings for those models.
NOTE: tapered kit will not fit Renthal Twin Wall or Barkbusters VSBar
Construction of these handguards feature heavy duty aluminum guards with colored plastic deflector shields. They offer great protection from those trees that jump out at you on the trail and the cold wind and rain you encounter on the street. They feature a deep bend on the outer bar end for maximum freedom of hand placement and high quality bar mounts on the inside.
Select your desired color.
Must add the corresponding size mounts to fit your handlebar.
For DR650 or other models with long levers add the optional universal fit Spacer Kit so you don't have to cut the balls off the end of your levers when installing these handguards. (May require additional adjustment or modification on some models.)
Please Note: These handguards do not fit the Yamaha T7
You can keep your Cycra handguards even if you upgrade your handlebars to a different width.
Replacement mounts that keep your Cycra handguards fresh and tight.
CNC-machined from billet aluminum for the best fit and strength.
Please Note: These handguards do not fit the Yamaha T7
FUZION guard feature the ultimate in hand protection with a unique design and flexible yet durable material.
The expanded coverage area sweeps back toward your hand significantly increasing coverage making it perfect for cold, muddy or wet conditions.
The FUZION features a unique two position mount and is constructed of molded light-weight closed-cell AEPE foam, which is crush-proof, water proof and extremely durable.
The FUZION will work great for road of offroad riding, where wind deflection is important, and or bouncing off trees is a common occurrence.
Kit includes mounts. Optional replacement mounts available.
Extend your comfortable riding season with Barkbusters BBZ cold weather protection handguards. Designed to fit with or without existing Barkbusters backbones or handlebar weights, these guards offer superb wind protection without limiting access to your grips or controls. Simple to install, they can be mounted or removed within ten minutes without permanent modifications. Ride with less bulky gloves in colder weather with the Barkbusters BBZ cold weather protection handguards.
Features:
- Fits most motorcycle handlebars
- Maximum cold weather protection
- Compatable with or without Barkbusters backbones
- Lined with waterproof membrane
- Windproof
- Full wrap design
- Allows full access of controls
- Does not block view of handlebar thumb controls
- Simple to install and remove
Whats in the box:
- Two BBZ cold weather handguards
- Mounting hardware
- Instructions
The OBR ADV Gear Enduro ¾ Grip Mitt is your answer to cold fingers! Our ¾ open design terminates right at the wrist, but still offers full coverage of the hand while blocking the swirling air flow that freezes finger tips. Their ¾ open design does not cover important controls such as Hi/Lo Beam, Turn Indicator, or Kill Switches making this Grip Mitt perfect for both Off Road, Enduro, ADV, and ATV applications with full wrap hand guards.
Features
- High strength and water resistant 1680d Ballistic Nylon construction
- Universal easy on/off Velcro snap strap attachment system
- Reflective Front Strip for High Visibility
- ¾ Open design provides full coverage of the hand while not impeding controls
- Works with OEM and Full Shield (Cycra/Trackside) style hand guards (Hand guard system required for attachment)
Droppin’ into the weather? Combine Bushwackers Hand Guards with rigid hand guards/deflectors and heated grips for the ultimate protection against the elements. Ride safer and longer with warm, dry and clean hands and controls. Essential gear for motorcycles, snow bikes and snowmobiles.
- Cold/wet weather comfort
- Brush, mud and trail protection
- Strap on/off in seconds
- Multiple mounting configurations to fit most motorcycle makes/models equipped with rigid hand guards and/or deflectors
- Tough stretch polyurethane strap (can be used separately)
- Custom wind foil shapes
- No stitching or pieces to fail
- When not using Bushwackers Hand Guards, straps have a thousand other uses: Lash water bottles, fuel, gear to tail rack. Hold flashlight in place while working in dark. And many others!
- Made in USA
REQUIRED EQUIPMENT: Motorcycle must be equipped with rigid hand guards or deflectors to support Bushwackers while riding.
Materials: Corona (UV) Treated, Matte Finish, .055 Gauge Polyethylene Plastic
Dimensions (flat): 13.5″ (length from end closest to bar clamp to end closest to bar end) x 16″ (widest part at end of bars) x 6″ (narrowest part nearest center of bar)
It may not surprise you that they are covered with HippoSkin™, their waterproof outer shell, and insulated with a generous layer of HippoFat™, a warm, flexible, closed cell foam insulation—both are designed to keep inclement weather away from your hands.
Sold in pairs.
Hand/brush guards are required for proper fitment and for safety reasons.
Hippo Hands go on and off in seconds and never require tools or hardware.
The Backcountry is 9" deep.
If you like to stand and ride, this is the model for you! But… these hand covers also fit to just about any bike. They are also a great option for cruisers with hand guards or lever guards.
They feature a durable, quilted interior and flexible, neoprene cuff which ensures a great fit on so many bikes. The Backcountry is their smallest, most easily adaptable hand cover.
The Backcountry features a front reflective panel for higher visibility in low light situations.
Extra protection in bad weather to help keep your hands warm and dry. These nearly double the protection from most plastic type deflectors.
The outer shell is made from heavy-duty 500-denier nylon with 1/2" closed cell foam to keep the wind, cold and rain off of your hands.