ProCycle currently has reduced staffing due to our state governor’s policies. Orders will be processed as efficiently as possible. Your patience is appreciated.
The CB500X is a new "light" adventure bike from Honda in 2019. It has been around since 2013 but, until recently did it receive the appropriate upgrades to make it more adventure worthy.
Powering the CB500X is a 471cc fuel injected parallel twin with DOHC, all mated to a wet 6 speed transmission.
| Chain Size | Front Sprocket | Rear Sprocket | Front Tire | Rear Tire | Spark Plug | |
| 2019 - Present | 520x112 | 15T | 41T | 110/80-19 | 160/60-17 | CPR8EA-9 |
| 2013 - 2018 | 520x112 | 15T | 41T | 120/70-17 | 160/60-17 | CPR8EA-9 |
ProCycle's custom calendar features specially selected customer submitted photos from around the world.
The desk top is 6" by 3.75" the perfect size to sit on your desk.
The wall calendar is 11" by 17" when fully open for use on your wall.
Keep essential items easily accessible with the OBR ADV Gear Big Sky Tank Bag. The OBR ADV Gear Big Sky Tank Bag utilizes a detachable base panel that attaches and secures easily to any bike via two adjustable buckle straps at the rear of the bag and one adjustable buckle strap at the front. A padded spacious main compartment is perfect for carrying those items you wish to keep close such as cameras, documentation, rain jacket, etc. Two smaller lid pockets sit above the main pocket for storage of smaller items. Designed with the larger ADV bikes in mind, but will also fit the Enduro and Mid-Size Dual Sports.
Features:
Premium Tank Bag at Promotional Pricing While Supplies Last!
Our logo on a 20oz double wall 18/8 stainless steel thermal tumbler with copper vacuum insulation, threaded snap-fit lid, and powder coated finish.
The copper plating on the inner wall is an extra defense against temperature transfer. Heat escapes much slower so your hot coffee stays hot even in a snow storm, and heat enters much slower so your ice water doesn't melt even under a blistering summer sun.
We have personally tested this bottle with 160° water placed on it's side for 7 hours, mimicking being in a saddle bag with coffee from the morning campsite and found that the bottle did not leak when the lid was properly secured and the water only dropped to 113° and the end of our test.
Pair it with the OBR bottle wrap for even better value and have a holder on your luggage for your new bottle for ease of access and security.
High-performance clamp kits feature marine-grade 18/8 stainless steel clamps with rounded edges, smooth inners and polished surfaces; contain all clamps necessary to complete installation of radiator hose kit.
CNC machined oil filler cap with locking clip to keep it in place in the roughest conditions. The cap is pre-drilled and the locking clip is safety wired to the mounting tap with a section of silicon tubing, that will not melt or discolor, over the wire. First class all the way. Available in Silver, Black, Blue or Red.
Hardened chrome vanadium steel with built in rubber insert to hold spark plug steady.
Thin wall bi-hex sockets designed to access narrow spark plug holes.
Fits 3/8" square drive and hex drive, 16mm, 18mm.
Keep your motor running right with a fresh plug.
NGK Spark Plugs is the largest OE supplier and manufacturer of spark plugs in North America.
Price reflects the quantity of spark plugs required for your make and model.
Includes degree wheel, dial-gauge, multi-position stand, extension, 3-sizes of positive-piston stops, and a handsome wooden carrying case.
Made from medium carbon steel with hardened jaws. It features spanner pins and the jaws open up to 5" wide. It's ideal for holding clutch hubs, flywheels, gears, sprockets, etc. Made by Motion Pro.
This tool is designed to separate vertically split crank case halves on two and four stroke engines. Adjustable arms allow it to be used on multiple bolt patterns found on a variety of makes and models of motorcycles. Industrial grade steel construction with black oxide finish for long service life. Comes with 8mm mounting bolts and 6mm adapters. Protective carrying case included.
For easy removal of recessed oil filters.
Conical point screws pierces and grabs the metal end cap of the filter.
reduces potential damage to the engine cases.
NOT for use on re-usable oil filters.
A 3-pack of easy to apply strips measure the temperature of engine, suspension, and radiator components. Temperature range 146° to 248°
Thread Chasers are designed to clean and re-cut damaged aluminum threads.
this kit contains the two sizes most common on metric motorcycles, M6x1.0 and M8x1.25.
Thread Chasers also remove dirt and metal shavings that become captured in thread grooves.
Uses 8mm or 10mm hex sockets, a Must for all tool kits.
Dual marked feeler gauges. 32 blades from .03mm/.001" to 1mm/.040"
Sold in 6 packs
This canister by Pro Circuit allows you to move the overflow tubes from the carburetor up and out of the way. Universal application.
Quick release one-piece clamps that saves space. These are great for fuel lines, controlling wires, and can be used many times.
Comes with 4 each of 8mm, 9mm 10mm, and 12mm.
No special tools needed, from Helix Racing.
Become more visible and look cool while doing it. The ProCycle Natural Tank LED Light Kit will add more light to your bike with the push of a button.
Kit includes a handle bar mounted lighted switch, two 12" LED light strips with adhesive backing, four saddle splice connectors, and a center harness for connecting to your bikes harness.
Installation is quick and easy.
*Please note All colors other than amber and white are recommended for off road use only*
If you're like us, you hate the long floppy vent hose hanging off the cap of your aftermarket tank. This one-way vent cap replaces the long hose with a short one only about 2" long. It allows air into your tank but prevents fuel from sloshing out. Machined from billet alloy and anodized for good looks.
Not for stock fuel tanks!
The small size and right angle hose barbs make this filter easier to fit into the small space between your fuel petcock and carburetor. Filter body is only 7/8" diameter. Straight filter is 2" long, 90 degree filter is only 1-5/8" long.
This filter is meant for 5/16" fuel lines. Only 1/2" thick it is small enough to fit just about anywhere.
Fuel supplies can be sketchy at times. This filter lives in your tank to trap dirt and debris as it is poured into the tank. Features a custom shaped adapter that fits securely under the gas cap, creating a leak-proof seal. If it stays out of your fuel, it can't get into the carburetor! Created by the filter experts at Twin Air, this filter fits IMS, Acerbis and Safari brand gas tanks.
Ordering new fuel line? How about a set of fresh zinc plated clamps to go with it?
These will be sure your fuel line stays connected. A pack of 8 clamps in 2 sizes to fit most 1/4 or 5/16 fuel hose.
Hose reducer to go from 5/16" line down to 1/4" line. Many bikes have 5/16" carburetor spigots but most aftermarket petcocks are 1/4". This solve the problem of mismatched sizes. Solid brass construction. Can be used to route or repair fuel lines, oil lines or air lines. Barbed ends provide a secure fit.
30" lengths. Sizes shown are ID. All of these lines are stronger and more durable than vinyl fuel lines and are resistant to swelling, UV light, as well as hardening and cracking.
Need to mount two containers? A water and a fuel? Two waters? Already have a RotoPax Mount for a single container? Get this extender to work in conjunction with a pack mount and that will be no problem! Single mount, two containers.
RotoPax holder made to mount a single Fuel and/or Water container.
Need to mount two containers? A water and a fuel? Two waters? Get the extender which allows you to stack two containers no problem! Single mount, two containers
RotoPax are Rotational Molded - the process which produces indisputably superior products.
Need to mount two containers? A water and a fuel? Two waters? Finally, you can stack multiple packs together! Use in conjunction with a pack mount. You will need to purchase the Single Mount as well as the Extender.
Quality Fuel pack that's slightly larger than RotoPax 1 gal.
Note: Mount listed is a RotoPax mount that will fit the Open Trail Fuel Packs.
Giant Loop's Gas Bag Fuel Safe Bladder conveniently transports 1 gallon of hydrocarbon fuel for power sports use in a collapsible welded film and ballistic nylon reinforced container that rolls up or packs flat when empty, weighing less than 1 pound.
The Gas Bag Fuel Safe Bladder Kit includes 2 pairs of Giant Loop's adventure proof 26" Pronghorn Straps plus a 3-Pack of Fast Funnel Disposable Fuel Funnels.
Each Gas Bag Fuel Safe Bladder is individually pressure tested and made in USA by Fuel Safe, a leading fuel containment manufacturer based in Oregon.
Auxiliary fuel tanks mount to handlebars, forks, or rear racks.
This Super Siphon has a (1/2 inch x 6 foot) long hose, which makes it quite easy to transfer fuel from one bike to another! Simply, shake the hose to prime it and get fuel moving. The hose is resistant to gasoline and any other hazardous chemicals. Roll it up, stuff it in your bag and you will be very happy whenever you need it.
This product is a windscreen lip that will offer more protection from the wind and weather. These mount directly onto your existing windscreen.
Windscreen attaches to your bike's handlebars. Fully adjustable mounting brackets. Includes 7/8' handlebar clamps. 14" tall & 10" wide.
Will not fit 1 1/8" oversize handlebars.
Puig Visor Clip-On
Universal design. Vents in the back improve airflow to motor. Smaller front reduces 'wind steer' and improves high speed stability.
Universal off-road front fender. Must be drilled to fit your mounting bolt pattern.
Replacement screen for Adventure-Spec Mini Fairing.
This is for screen only, please see Mini Fairing Support for complete assembly.
Limited availability in Blue only, due to manufacturer supply delays until 2021.
This frame includes six, white, full-spectrum LED bulbs on a 6-inch strip for bright illumination of your license plate. It is made in a sturdy cast aluminum, and is powder coated with a durable black finish.
Outside frame dimensions are 7.25" in. wide by 4.2". Center to center mounting hole distance is 5.7 in. All mounting hardware is included.
Adhesive heat shield for your new side panel plastics to protect it from the heat of your muffler.
Corbin seats are custom made to order. You can choose your preferred texture for the top and sides of the seat. Please give us a call if you would like other color options or materials.
Because Corbin seats are custom made they are carefully designed to provide a comfortable riding position. They are firm and supportive which allows you to ride all day without fatigue unlike the stock seat.
The default vinyl choices are black 'carbon fiber' on top and 'asphalt' on the sides. You can view all of the available materials and colors on Corbin's Website.
Corbin seats are custom made to order. Please allow 3 weeks delivery time.
Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a more plush and active ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.
Rally Tall seat is built up 1.75 inches and they leveled out the angle of the rider platform to reduce the slope-into-tank feeling of the stock seat.
On the Standard seat they built up the front, but dished out the rear slightly to level out the angle of the rider platform, and reduce the slope-into-tank feeling of the stock seat.
These features combine to offer a custom seat feel, and provide greater enjoyment and increased range on a long commute, or Dual-Sport ride!
This is the secret for being able to put in those 500 mile days. Even a good touring seat can feel a bit firm after a couple hundred miles. Sheepskin gives that little bit of 'cush' and provides superior air circulation. Velcro straps allow easy removal when you don't need it. Measures 14" wide by 19" long.
9" by 9" carbon fiber seat warmer that goes between your seat cover and the foam to keep your backside happy on those really cold days. This improved design produces 25% more heat than most other warmers using just 30 watts.
Kit includes the warming unit, with connector, 24" extension cable, rocker-type on/off switch and stub to splice into your wiring along with complete detailed instructions.
Features:
*2019+ Engine Guards Coming Soon*
Contoured alloy hand guards with inner mounts, allow space for the clutch cable and brake hose.
Images show a set of these hand guards installed on a set of CR High Gunmetal Fly Handlebars with large black deflectors. The far right image shows the need to flip the brackets that attach to the bar on the clutch and front brake side. On the front brake side the clamp must go over the front brake line while on the clutch side it goes under the cable.
These handguards come with mounts that will work on both standard and and oversize bars. The aluminum wrap-around bar is the biggest on the market with two large plastic shields that are also some of the largest available. The X-Factor hand guards offer great protection from the elements, especially during those colder months when you're trying to stretch out your riding season.
Works with 7/8" or 1-1/8" bars.
X-Factor guards require you to cut your lever ends down, or use short levers.
Replacement handguards for your Acerbis set up. Tough Polypropylene shields with a larger 6" outer diameter, built for extreme riding conditions.
The X-Factory Handguards from Acerbis feature an steel bar wrapped with an injection molded Nylon composite. A replaceable dual injected polypropylene shield mounts to the bar offering insurmountable protection from roost, debris, and extreme conditions.
A universal mount kit is included that allows for mounting on either 7/8" or 1 1/8" handlebars.
Weight:
360 grams/pair or
180 grams/each
Fitment Notes: If you have a hardware kit listed below see special fitting notes as additional parts may be required
BHG-010 Requires two additional M6x40mm countersunk bolts
BHG-032 R1200GS/A requires two additional M8x55mm countersunk bolts
BHG-045 G650GS requires two additional M6x65mm countersunk bolts
BHG-050 Will not fit
BHG-051 Requires two additional M6x50mm countersunk bolts
BHG-059 Tiger XC, XCA & XCX (all ’15 on) use M6x45mm bolt from BHG-059 kit
BHG-075 Will not fit
BHG-079 Will not fit
Extend your comfortable riding season with Barkbusters BBZ cold weather protection handguards. Designed to fit with or without existing Barkbusters backbones or handlebar weights, these guards offer superb wind protection without limiting access to your grips or controls. Simple to install, they can be mounted or removed within ten minutes without permanent modifications. Ride with less bulky gloves in colder weather with the Barkbusters BBZ cold weather protection handguards.
Features:
Whats in the box:
Protect your hands and levers with the Barkbusters Storm lever and weather protection handguards. Full wrap solid heat treated aluminum bars with secure two point mounts on each side provide strength while attractive and generous guards provide shelter from the wind and weather. Ride longer with the Storm handguards and complete mounting kit by Barkbusters.
Features:
What's in the box:
Not recommended for Africa Twin, T7, Himalayan, or V-Strom. Please see specific listings for those models.
Maximize your wind protection with the Barkbusters largest handguard plastic! For use with single sided Storm mount and all Barkbusters backbone handguards
Keep your hands and controls protected from the wind and impact with Barkbusters VPS lever and wind protection handguards. Heat treated aluminum backbones with two mounting points of these handguards provide the strength needed to prevent a tip-over from ending your motorcycle ride. Impact resistant deflectors, available in multiple colors, provide protection for your hands from the wind and brush. Ride longer, more comfortably with Barkbusters VPS lever and wind protection handguards
Features:
What's in the box:
Not recommended for Africa Twin, T7, Himalayan, or V-Strom. Please see specific listings for those models.
Replace the deflectors on your aluminum bar backbones with Barkbusters VPS wind protection replacement handguards.
Construction of these handguards feature heavy duty aluminum guards with colored plastic deflector shields. They offer great protection from those trees that jump out at you on the trail and the cold wind and rain you encounter on the street. They feature a deep bend on the outer bar end for maximum freedom of hand placement and high quality bar mounts on the inside.
Select your desired color with the corresponding size mounts to fit your handlebar.
Replacement handguards for your Cycra set up. Injection-molded high-impact plastic replacements. Includes all hardware needed for mounting.
Fits Moose and other aluminum hand guards
The OBR ADV Gear Enduro ¾ Grip Mitt is your answer to cold fingers! Our ¾ open design terminates right at the wrist, but still offers full coverage of the hand while blocking the swirling air flow that freezes finger tips. Their ¾ open design does not cover important controls such as Hi/Lo Beam, Turn Indicator, or Kill Switches making this Grip Mitt perfect for both Off Road, Enduro, ADV, and ATV applications with full wrap hand guards.
Features
Extra protection in bad weather to help keep your hands warm and dry. These nearly double the protection from most plastic type deflectors.
The outer shell is made from heavy-duty 500-denier nylon with 1/2" closed cell foam to keep the wind, cold and rain off of your hands.
FUZION guard feature the ultimate in hand protection with a unique design and flexible yet durable material. The expanded coverage area sweeps back toward your hand significantly increasing coverage making it perfect for cold, muddy or wet conditions. The FUZION features a unique two position mount and is constructed of molded light-weight closed-cell AEPE foam, which is crush-proof, water proof and extremely durable. The FUZION will work great for road of offroad riding, where wind deflection is important, and or bouncing off trees is a common occurrence. Kit includes mounts. Optional replacement mounts available.
Comfortable Oversize (or Fat Bar) Handlebars. For bikes with standard 7/8" handlebars these will require the use of a 7/8 to 1-1/8 adapter. Black in color. Raise your bars and get rid of the crossbar that obstructs your view of the speedo. Works with stock controls and cables.
These handlebars are high quality at an affordable price. Several bikes here in the shop use these bars and we like them.
Some bends and colors are currently delayed until December 2020. Order now for fastest delivery.
These 7/8" bars fit in the stock clamps and raise your grips a couple inches. They look great too!
These versatile Risers allow you to clamp a 7/8" diameter handlebar or you can remove the 7/8" reducers and then clamp an 1- 1/8" aluminum "fatbar". If you are thinking of going to a fatbar after you bend your stock set or just want the versatility and option to run any bar, this is the riser to go with. Reducers lock into risers to insure no slippage between components. Anti-Vibe Risers may interfere with aftermarket large capacity fuel tanks, and some steering stem clamp configurations (use standard pivoting risers). These risers use 8mm bolts. Always check and confirm that your bike has adequate cable and brake line length before installing any handlebar risers.
This unique design from Rox allows you to move your bars either closer (1" up and back) or further away (1" forward and 1-1/4" up) depending on rider preference. These risers have an oblong mounting hole so that they will fit virtually any triple clamp with 8mm bolts. A set of reducers lock into the risers ensuring no slippage whether you have a 7/8" or 1-1/8" bars
This grip features BluPulse™ ‘Adaptive Thermal Regulation’ technology, which combines thermal sensors in each grip with intelligent micro electronics in the external controller, and allows a rider to select between six temperature settings with a simple push of a button. A blue LED indicates both the selected temperature setting and heating status while the micro processor varies the amount of heat generated to maintain the selected temperature.
A key component with A’ME’s new Heated and Non-Heated Sport Bike Grips are five interchangeable throttle cable Cams that work in conjunction with the right hand throttle sleeve which will allow the grip to fit most bikes.
A’ME Chicane Sports Bike grips are composed of Vulcathane,™ a specially Blended rubber compound combined with UV stabilizing ingredients that exhibit superior oxidation and ozone resistance. As a result, A’ME M/C grips will not absorb moisture, deteriorate, harden or become slick with age, all the while providing and maintaining comfort.
NOTE: The A'ME thru-hole design also allows you to mount your stock or aftermarket bar ends.
Features:
Highly efficient design delivers warmth faster than traditional heated grips.
Choose from the standard five level push button temperature controller, or the LCD display controller which shows the selected heat level and available battery voltage.
The Apollo Heated Grips are designed with an integrated adjustable thumb switch, which allows them to easily fit on any kind of motorcycles on the market. The integrated thumb switch gives control to the rider to adjust the temperature level while keeping hands on the bar for a safer ride.
Its wide temperature setting range will keep the rider comfortable under the cold riding conditions.
The 5 color LED display will enhance the visual look of the heated grips and will allow the rider to quickly know at which heat level the grips are set.
This system will also detect if the battery voltage is too low and will automatically shut down the heated grips in order to make sure the rider have enough power to start the engine or use the motorcycle.
Specifications:
These grips feature a thicker design that dampens vibration. The soft shoulder allows ease of movement. Three wire-tie grooves are molded into the grip to make securing them a breeze. We think they are great!
Reduces vibration and cushions impact. Inner core compound perfects the bonding interface with bars. Anti-Rip Tip™ uses denser compound to increase life of grip. Designed to self-clean and shed mud away from outer surface. Tacky gel-like surface compound is perfect for offroad and MX.
Each pattern is available in three advanced synthetic rubber compounds. This means you can have the optimum combination of strength, tackiness and shock absorption to suit every riding condition and individual style. Soft grip is extremely soft, giving you a very comfortable ride, great feel and reduces the chance of blisters; however, because the grip is so soft, it wears quickly. Medium is a compromise between firm and soft. Firm grip has the same feel as a stock grip, it is very strong and has very good resistance to tearing and abrasion. Half Waffle has waffle pattern in finger area for traction and diamond pattern on palm side to reduce blisters. Full Waffle: designed after the CR Honda® grip.
This little jewel reduces hand fatigue and cramping on long rides or daily commutes. The Crampbuster is not a throttle locking unit but, rather a simple clip-on device which allows you to relax your grip while riding.
The Go Cruise cruise control mounts over the throttle grip and rests on the brake lever to hold your throttle open, allowing you to stretch and rest your hand on long rides. Installs and removes in seconds with no tools. You can roll off the throttle manually to disengage the Go Cruise.
Attach this over your brake lever and hand grip, squeeze the brake lever, pull the locking bar in and lock the black portion down. This creates a locked front brake, making parking safe and secure with about 5 seconds of effort.
To unlock the BrakeFix, you just lift the back of the black hooking portion to release it. This takes about 2 seconds. Perfect for use with Snapjack type stands or just parking on an incline.
Replaces all 2 bolt style clutch/brake lever mount clamps on your clutch or brake lever holder. Can help save space on short bend handlebars.
With the split back, you don't need to remove your grip or throttle tube, just put it on and tighten 'er down. Put the mirror in and hit the road. Clean and simple.
One folding mirror. Includes handlebar mount. Can be used on left or right side. Sold each.
This new mirror can be folded out of the way when it's time to hit the trails. These are quite similar to the very popular KTM folding mirrors but at half the price. Fits either left or right side and includes handlebar mount.
Made from a nylon and fiberglass composite, these mirrors are extremely durable. They easily fold out of the way when you head off-road.
Enduro Mirror 4"
Ideal for dualsport use, where you want a low profile when folded down. SAE spec convex glass gives a much greater field of view than flat glass.
ADV Mirror 3" x 5"
Adventure mirrors are designed for adventure riding where you want your mirror extended most of the time.
Mirrors mount to any 10mm perch. Mirror and arm included as shown in pictures.
Sold individually.
This new mirror screws into your stock mirror mount but can be folded out of the way when it's time to hit the trails. These are quite similar to the very popular KTM folding mirrors but at half the price. Fits either left or right side.
Sold individually. If a set is needed, order two.
+1 541-688-9543