Featured Products

Back to Top
New! 061815

LeoVince X3 Slip-On Muffler


No repacking required! The LeoVince X3 Enduro is made with TIG welded stainless steel internals and aluminum outer shell. It features a semi-direct chamber design that is maintenance free. It's quiet too! Our own in-house testing showed a 89dB sound level using the USFS J1287 testing procedure. 89dB is louder than stock but significantly quieter than any other aftermarket muffler. It includes a certified Spark-Arrestor.

New! 021016

Evans Waterless Coolant


Evans Waterless Coolant can be used for all water cooled motorcycles to eliminate overheating. With a boiling point in excess of 375° F, it will not vaporize, thus eliminating overheating, boil-over and after-boil. Another benefit is additional power by eliminating pre-ignition and detonation caused by overheating improving combustion efficiency.

FCR39 Carburetor Kit


This kit replaces the stock carburetor with a true pumper carb. This will bring out the beast in the DRZ.

Kit includes a brand-new carburetor, throttle cables and a new throttle assembly (which is required for the new pull-push cable system).

Warp 9 Replacement Radiators


These replacement radiators will maximize cooling, increase overall horsepower and improve your engine's longevity by reducing running temps by up to 30 degrees.

There is a 25% increase in capacity and all radiators include a 16 lbs. radiator cap.

Click gray button below and verify fitment and other requirements.

Engine

Back to Top

$181.95

Wiseco Replacement Pistons

DRZ400 all

Stock bore replacement pistons from Wiseco. You have your choice of the standard compression ratio of 12.2:1, or a high-compression ratio of 13.5:1. This high-compression kit will run fine with standard pump Premium.

Kits include piston, rings, wrist pin and circlips. Scroll down for gasket sets.


$789.95

Athena 440cc Big Bore Kit

DRZ400 all
  • Includes aluminum cylinder, piston kit, and special gasket set designed for larger water jackets
  • Bolts on with no machining required
  • 94mm big bore piston
  • Aluminum cylinder designed with wider water jackets for better cooling.
  • Forged hi-compression piston
  • Includes all necessary Rings, Clips, and Gaskets.

$629.95

Cylinder Works 434cc Big Bore Kit

DRZ400 all
  • Direct bolt-on, ready-to-install cylinder; requires no replating and looks virtually identical to the OEM
  • Nickel Silicon Carbide plated for long life
  • Honed to exact size for easy piston installation
  • Big bore cylinders do not require any machine work
  • Come complete with gaskets, cylinder, 94mm piston, rings, pin and clips

$349.95

Hot Rods +4mm Stroker Crank

DRZ400 all
  • Hot Rods complete stroker crank assembly includes +4mm stroke for maximum power and performance output.
  • Hot Rods constructs their complete stroker crank assembly to meet or exceed OEM specifications for maximum durability.
  • Hot Rods stroker cranks are completely rebuildable and have been trued to within 0.001" from the factory.
  • The Hot Rods stroker crank increases the stock displacement to 424cc when used with the stock bore piston or 462cc when used with a 94mm big bore kit.
  • Main bearings sold separately.

$1099.00

Big Bore Stroker DRZ462 Kit

DRZ400 all

All in one package.

  • Hot Rods complete +4mm stroker crank assembly
  • 94mm big bore cylinder and piston kit
  • Complete gasket set with seals
  • Includes new crank bearings

We suggest adding a set of HotCams camshafts and a new clutch kit for the best results.

  

$64.95

Hot Rods Crank Bearings

DRZ400 All

New Bearings for your DRZ400. If you are in the lower end doing work, good insurance to put in a new set of bearings.


$88.95

Complete Gasket Set with Oil Seals

DRZ400 all

A complete set of gaskets, orings and oil seals. Everything you will need when doing a complete engine re-assembly.

Select



Side Cover Gaskets

DRZ400 All

Side cover gaskets and O-ring for service or repair.

  • Click on picture to expand for details.
Choose Plug Type:
Standard $5.95


Dual Electrode $9.95

Iridium $10.95


E3 Spark Plugs $9.95

New! 012916

Spark Plugs

DRZ400 All

Keep your motor running right with a fresh plug.

A Dual Electrode spark plug will last longer than a single electrode plug because the wear is shared between the electrode.

Iridium spark plugs are made with higher quality materials. It will last longer than a standard plug, meaning you won't have to replace it as often.

The E3 plug has an almost circular electrode supported on three sides that creates a flame more toward the piston and the bulk of the air/fuel mixture giving it faster flame growth and a larger flame kernel providing better throttle response. The multiple sharp edges to the circular sharp edge of the center electrode prevent the 'arc welding' type of material depletion of other electrode plugs giving this plug an extremely long life. See image of E3 electrode below.


$79.95

Valve Shim Kit

9.48mm

Includes three valve shims of each size from 1.20 to 3.50 in .05 increments. 141 shims in total. 57 cents per shim!


$39.95

Timing Inspection Plugs


Billet plugs for your left side case. Includes both the timing mark plug and the crankshaft access plug.


$219.95

Warp 9 Replacement Radiators

DRZ400E-'02-'07 and DRZ400S/SM '00-'08

These replacement radiators will maximize cooling, increase overall horsepower and improve your engine's longevity by reducing running temps by up to 30 degrees.

There is also a 25% increase in capacity. All radiators include a 16 lbs. radiator cap.

Please be sure that you have one of the models listed as these radiators will NOT fit other models or years.

  • 42mm Extra Deep Cores
  • TIG Welded Seams and Joints
  • Less expensive than OEM
  • Available in Silver

! Warp 9 oversized radiators do not work with oversized fuel tanks or radiator braces

Select Stage:


$349.95

HotCams Performance Camshafts

DRZ400 all (Made in USA)

As the leader in innovation, design and development of aftermarket high-performance camshafts, Hot Cams is certain to provide the added boost that enthusiasts are looking for.

Designed, dyno proven and made in the USA, Hot Cams performance camshafts are one of the most economical, reliable and easy to install ways to add a 5-10% power gain to your bike.

Stage 1: These cams provide better low RPM torque, pulling power, and throttle response.

Stage 2: These cams will provide improved full throttle torque and horsepower at all RPM 4000 and up


$71.95

Wiseco Cam Chain

DRZ400 all

A top quality cam chain from the folks at Wiseco. New cams, big bore kit, high-mileage motor, you might want to think about a new cam chain. Direct replacement for stock unit.


$62.95

Manual Cam Chain Tensioner

DRZ400 all

Solid reliability and easy installation. Bling factor too. This manual tensioner is a good upgrade for any modified motor, especially if it is ridden hard. A new gasket is included.


$89.95

EBC Complete Clutch Kit

DRZ400 all

Replace your worn clutch plates and springs to reduce fade and slip.

  • Complete set of friction plates, steel plates, and springs
  • Heavy-duty springs help prevent clutch slip
  • Restores proper stack height, fixes clutch slip caused by wear and tear

$249.95

Kickstart Kit

DRZ400 E/ES/SM

Add a backup kick start system to your electric start DRZ400. Complete with everything you need to add the kick starter to your bike.

This kit will fit all DRZ400s but you can only install the manual decompression lever on the 2006 to Current DRZ400 E models.


$11.95

Magnetic Drain Plug

DRZ400 all

Extra protection for your motor. Strong magnet at the end of the plug picks up metallic flakes in your oil, protecting your engine.


$34.95

Hi-Flo Oil Filter Value 10-Pack


Providing unbeatable performance and exceptional value, Hiflofiltro is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide. The filters are also supplied to original equipment manufacturers as well as private label brands.

You pay $3.50 per filter with our value 10-pack!

$29.95

New! 012916

FLO Stainless Steel Reusable Oil Filter

DRZ400 All

Made from laser-cut, medical-grade, 304 stainless steel micronic filter cloth, this filter provides 200% more filter area over many paper filters, catching debris down to 35 microns. The FLO filter pleat seam is welded and able to withstand up to 600 deg. F. Filter maintains consistent flow under all conditions including extreme heat, the presence of water and cold start-ups where paper filters can flow so poorly that they often cause the bypass valve to open and allow unfiltered oil to enter your engine.

This cleanable oil filter should be the last one you ever purchase.


$11.95

Oil Filter Magnet


  • Easy to install. Attaches to base of standard oil filter.
  • This powerful six point magnet traps abrasive hard metal particles down to 1 micron. Standard oil filters only trap particles down to 90 microns, leaving behind the most harmful particles to circulate through your engine.
  • Reduce wear, and significantly increase your engine life.
 

$29.95

New! 020216

Evans Waterless Coolant


Evans Waterless Coolant (EWC) can be used for all water cooled motorcycles to eliminate overheating. With a boiling point in excess of 375° F, it will not vaporize, thus eliminating overheating, boil-over and after-boil. At the other end of the spectrum, EWC freezes below -40° F.

EWC also delivers more power by eliminating pre-ignition and detonation caused by overheating improving combustion efficiency. It also generates very low vapor pressures which reduces strain on cooling system components. EWC comes in 1/2 gal. containers.

Installation requires just a bit more than dumping the old fluid and adding the EWC. Please click on the 'Instructions' button below to see those directions.

Evans Waterless Coolant Installation Instructions

When converting an engine from a water-based coolant to Evans Waterless Coolant (EWC), great care should be given during the installation (conversion) process to insure that all of the old water-based coolant is removed before installing new EWC.

There are a number of methods to use depending on the machine layout and ones mechanical abilities. If you are not comfortable with removing your thermostat and working on the entire cooling system, it is acceptable to drain your system as best as possible, and follow the instructions below.

  • Begin with a cold engine.
  • All of the old antifreeze must be removed from the cooling system. Conventional antifreeze contains water and water contaminates. DO NOT flush with water. (If the system is badly corroded or contaminated with non-coolant products [i.e. rust, oil, dirt, etc.], you may flush with water and use a chemical cooling system cleaner. More care will be needed to ensure that all the water is then fully removed.)
  • Drain cooling system including expansion tank according to the owner's manual.
  • If possible, remove a low hose connection, typically at the coolant pump, and blow air in through the radiator or system-fill opening to push out all the old antifreeze. A high-volume air source is preferred over high pressure air. If compressed air is used to help remove the old coolant and water, be aware that it can damage cooling system components. The use of high volume, low pressure air is preferred because it is safer, and in most cases, more effective.
  • Close up drains, attach any hoses that were removed, and fill system fully with EWC. Run engine until thermostat opens and fluid is circulated thoroughly. Allow engine to cool to relieve any possible water vapor pressure.
  • Drain system and blow out as well as you can again.
  • Close up drains, attach hoses, and fill system with EWC. Fill expansion tank to cold line. Check fluid level after initial operation.

Dispose of drained fluid responsibly. Treat EWC the same as antifreeze for disposal purposes.

EWC expands 7% at operating temperature, about the same as antifreeze. If there is no expansion tank on the system, the radiator will purge a small amount upon warm up. Once cooled, this is now the system's operating level.

EWC is a blend of glycols and so it is compatible with the chemicals in antifreeze so that if you must add water to your system in the case of an emergency, the mixture will perform the same as antifreeze and no worse.


$19.95

Hi Pressure Radiator Cap

DRZ400 All

The higher pressure in the radiator raises the coolant boiling point and increases protection from coolant loss due to overheating.

23 PSI - 1.6 Bar


$99.95

Radiator Hose Kit

DRZ400 S/SM
  • European grade high-temperature silicone guaranteed to 356° F
  • Smooth flow and improved insulation promotes radiator efficiency and improves engine cooling
  • Single molded, Y-piece hoses eliminate the need to reuse OEM 3-way fitting which reduces weight and eliminates leak points
  • Three layers of reinforcement fabric offer high burst pressures and provided better debris/crash resistance
  • UV stable colors don't fade with heat or sun and are color matched to OEM brands

$30.95

Service Manual

DRZ400 All

Clymer repair manuals provides step-by-step procedures based upon the complete disassembly of the motorcycle. This hands-on experience combined with extensive research results in a manual that is both user-friendly and detailed. Hundreds of original photos and illustrations guide the reader through every job.

Whether you're interested in routine maintenance tasks, troubleshooting, or more extensive repairs, the in-depth coverage provides indispensable information about your DRZ400.


$16.95

Clutch Holding Tool


clutch tool

Need to remove your clutch assembly? This holder is the quickest and easiest tool out there to get a grip on that hard to handle hub. Laser cut to the exact pattern that EBC makes their clutch plates from, it makes loosening and re-tightening the clutch nut easy. All of that and no worries about doing any damage to your expensive clutch hub.

Bottom line, if you have to hold your clutch hub to remove it, there is no better way to do it.

Exhaust

Back to Top

$319.95

FMF Powercore 4 Muffler

(Made in USA)

New from FMF. The Powercore 4 spark arrested muffler. FMF developed the PowerCore 4 to increase the horsepower and torque throughout the entire power curve. Space Age packing for maximum packing life. Removable spark arrestor included. Louder than the Q4. Approximately 99db stock or about 94db with optional Quiet Insert (see below) installed.


$37.95

Quiet Insert for Powercore 4

(Made in USA);

The Quiet Insert will shush up the sound level of the Powercore 4 from about 99db down to about 94db.


$209.95

FMF PowerBomb Stainless Steel Headpipe

(Made in USA) DRZ400 all

The PowerBomb header promotes better flow by allowing a small expansion of the exhaust gasses. The 'bomb' also acts as a pre-muffler taking the edge off of overall sound levels.


!  Headpipe orders ship Parcel Post Only! within the US. Why?

The redesigned PowerBomb is a four-stroke header that incorporates FMF's patented PowerBomb module at a precise location in the initial stage of the header. By positioning this "Bomb" at a key point in the system, increased performance and flow is achieved through the expansion and contraction of exhaust sonics through the system. Result is a flow increase of nearly 10%! The outer chamber in the Powerbomb allows the air to expand, cool and ramp back up at a higher velocity. Additionally, the PowerBomb is a "pre-muffler" of sorts which helps to lower the bikes sound output by providing more sound absorbing surface area for the sound medium (exhaust gases).

$32.95

New! 010516

Stainless Steel Heat Shield


This universal heat shield provides great looks at a great price.

  • Fits all 1-1/2" - 2-1/8" Pipes
  • Measures 7-1/4" x 3"

$34.95

FMF Heat Shield


Have you lost your stock heat shield, or need one on an aftermarket head pipe? FMF makes this nice unit that includes clamps, heat shield with the FMF logo and button head screws to hold it on.

Select items




Cycle Performance Exhaust Wrap

(Made in USA)

Set your bike apart with a custom exhaust look. Withstands direct heat up to 2000°F

  • 2"x25' wrap available in black or natural
  • 4ea stainless steel tie wraps

$31.95

Universal Stainless Repack Kit

(Made in USA)

Re-pack your silencer with this pro-quality, three layer packing system and restore the power you have blown out.

Kit includes:
  • 60"x20"x1⁄4" glass mat.
  • 7"x20" stainless wool
  • 8"x20" stainless mesh
  • Twelve 3⁄16" rivets

Select items




Exhaust System Gaskets



The exhaust gasket seals the joint between the head pipe and Exhaust port. These gaskets are designed to crush a little bit to tightly seal where the pipe fits to the head. Get a fresh one now avoid having an exhaust leak when you install your new exhaust.

The muffler joint gasket seals the joint between the head pipe and muffler. These gaskets are easily damaged when removing the original muffler. FMF mufflers (Q4 or PowerCore 4) do not require a joint gasket but the all other aftermarket mufflers as well as the stock muffler do require a joint gasket. Get a fresh one now to ease installation of your new performance muffler.


$349.95

FMF Q-4 Slip-On Muffler

(Made in USA)
  • The Q4 employs intricate chambers, baffles and proprietary multistage packing material making it the best performing quiet muffler available
  • Constructed from aircraft grade aluminum and high strength stainless steel
  • Sound output 96dB
  • Several pounds lighter than the stock muffler

$549.95

FMF Q4 & PowerBomb System

(Made in USA) DRZ400E/S/SM all

Buy both and save. Includes the FMF Q-4 and FMF header pipe.

  • The Q4 employs intricate chambers, baffles and proprietary multistage packing material making it the best performing quiet muffler available
  • Constructed from aircraft grade aluminum and high strength stainless steel
  • Sound output 96dB

!  Exhaust system orders ship Parcel Post Only! within the US. Why?



$433.95

New! 001815

LeoVince X-3 Enduro Slip-On Muffler


No repacking required! The LeoVince X3 Enduro is made with TIG welded stainless steel internals and aluminum outer shell. It features a semi-direct chamber design that is maintenance free. It's quiet too! Our own in-house testing showed a 84dB sound level using the USFS J1287 testing procedure. 84dB is louder than stock but significantly quieter than any other aftermarket muffler. It includes a certified Spark-Arrestor.



$374.95

New! 060116

Yoshimura Slip On RS-3 Muffler


Yoshimura RS-3 that will slip right on to your stock header. Made by hand to the highest quality standards using the championship-winning racetrack experience and their extensive R&D facility ensure these pipes perform and will last.

Both full systems and slip-on mufflers include 96 dB sound insert/U.S.F.S.-approved spark arrestor installed in the muffler. Mid-pipe is stainless steel while the stinless RS-3 oval muffler design has a slim profile with an aluminum end cap.

Muffler for S/SM model is the RS-3 Comp. model


New! 060116

Yoshimura Exhaust Systems



The race-bred RS-3 exhaust has proven to be extremely popular among rider looks for a combination of performance and value. It enhances performance dramatically, provides an enviable exhaust note and offers the unmistakable look and sound of Yoshimura. RS-3 mufflers feature a straight baffle that leads to a single turn-down machined aluminum end cap.

The different systems are configured as shown below.

  • System for '00-'07 DRZ400 has a SS header, SS muffler and Aluminum end cap
  • System for '00-'12 DRZ400S/SM has a SS header, Aluminum muffler and SS end cap
  • Race System for '00-'12 DRZ400S/SM has a SS header, Carbon Fiber muffler and SS end cap

All models have a USFS Approved spark arrester in a oval-shaped sleeve with a large volume of packing material.


New! 060116

Yoshimura SM Exhaust System

DRZ400S/SM '00-'16

The RS-4 Twin Pipe kit was previously only available as a custom system for Kevin Schwantz. He wanted his motorcycle to look like a "Hot Rod" and have a "cool" factor. We obliged and one of our most sought-after-yet-unobtainable pipes was created, which was not available to the general public, until now.

Yoshimura is offering these incredible "Twice Pipes" which are completely fabricated by hand and TIG welded to perfection. They certainly sit at the high end of what is available for the mighty SM... but that's what Kevin wanted! The pipes have a stainless steel header and "Y" pipe mated to twin carbon fiber RS-4 mufflers for incredible looks and performance. The kit also comes with a custom Yoshimura side stand.

  • Pentagonal-shaped sleeve
  • Front muffler cap functions as a polyresonant chamber which helps reduce noise
  • Two-stage stepped baffle
  • Carbon fiber end-cap
Select Model

$264.95

DG Performance V2 Slip-on


The V2 Series Slip-On muffler features an aluminum body, TIG welded components, stainless steel inlet tube and a great new look. This Lightweight Slip-On weighs approximately 5.5 lbs.

The DG Performance systems offer increased throttle response, power and torque. Standard sound level is approximately 98 db. Equipped with a US Forestry approved spark arrestor.

Select Model


DG Quiet Insert


The 1" Quiet Insert will shush up the sound level of the DG pipe from about 99db down to about 96db. Definitely takes the sharp edge off the bark.

Select items




Muffler Packing Pillows


The latest in muffler packing technology. Spec 31 high performance muffler packing resists breakdown up to 1400°F, is universal and easy to install. Pillow can be trimmed to length to fit mufflers up to 20" long. Comes with cap stuffer to fill packable end caps.

Fuel & Intake

Back to Top

$899.95
On Sale! $699.95

FCR39 Carburetor Kit

DRZ400S/SM

This kit replaces the stock carburetor with a true pumper carb. This will bring out the beast in the DRZ.

Kit includes a brand-new carburetor, throttle cables and a new throttle assembly (which is required for the new pull-push cable system).


$33.95

Moose Racing Triple Layer Air Filter

(Made in USA)DRZ400 all
  • Unique triple stage foam filter designed for the most extreme conditions
  • Eliminates the need for power robbing dust covers and outerwear covers
  • Increased protection against silt, water, and sand
  • Allows for extended filter service intervals
  • Can be cleaned, re-oiled, and re-used like a 2 stage filter
  • Used by factory off road teams around the world

$28.95

Twin Air Filter

DRZ400 all

Twin Air Filter's patented design, high quality materials and superior construction deliver unbeatable performance and protection - and make Twin Air Filters the hands-down choice of more World and National Champions than all other filters combined.

An air filter is your engine's only protection against the elements, and your stock filter isn't up to the task. Replace it with a Twin Air-the #1 filter system proven on motocross tracks around the world.

Twin Air's fused layers of open-pore foam and fine inner foam trap even the smallest particles-without restricting airflow.

Select Kit

Evolution Air Filter Oil


This advanced filter oil kit by No Toil is alcohol free, completely biodegradable and compatible with all foam filters.

  • Offers superior protection
  • Waterproof yet easy to clean
Select Size

No Toil Filter Rim Grease


No Toil rim grease is a high viscosity, non petroleum based compound specially engineered to provide the ultimate filter rim to air box seal.

  • Biodegradable
  • Non toxic, Waterproof
  • Easy cleaning in seconds with water and No Toil cleaner

$21.95

Premium 5/16" ID Fuel Line

Sold in 3' lengths  (Made in USA)
  • Stronger and more durable than vinyl fuel line
  • Resistant to swelling, direct sunlight, hardening and cracking
  • Flexible in temperatures from -35°F to 165°F
  • 1/2" OD

Not for fuel injected engines


$10.95

Fuel Line Protector

7/16" OD fuel line  (Made in USA)
 
  • Protects vulnerable and exposed hoses from abrasion
  • Made from stainless spring steel
  • Sold in 10" lengths

$29.95

'Raptor' Petcock


Replace your stock vacuum operated petcock with this manual one. Must be shut off any time the bike is parked for more than a few hours. Fits stock or aftermarket tanks. Plastic tanks may need the hole 'ovalized' to fit the dual standpipes.

! If you have a Clarke brand tank, please order the petcock for metal tanks.


$117.95

Pingel Fuel Petcock

(Made in USA)

A popular upgrade from the stock vacuum operated fuel valve. Manually operated. Must be shut off any time the bike is parked for more than a few hours. Fits stock tank or aftermarket tank and has both main and reserve. Fully rebuildable.


$84.95

JD Jet Kit

DRZ400S/SE/SM

This kit is for the 36mm BSR Mikuni CV carburetor and includes 2 Needles that have been developed by JD Jetting and manufactured for them to their exacting specifications. These two needles allow a wide range of tuning possibilities and provide correct fuel delivery at any throttle position.

4 allen type screws for the top of the carburetor are also enclosed should you strip out the stock screws during your tuning process. Complete instructions with photos, jetting suggestions for different set-ups and situations, 5 Main Jets, a Pilot Jet and a drill bit complete the package.


$54.95

Dynojet Jet Kit


  • Provides a simple and affordable solution to carburetor tuning problems
  • Allows you to tune your bike for increased power and smoothness while
    retaining fuel economy
  • Includes a guide booklet on how to install and use your jet kit to it's full potential

$56.95

K&N Air Filter

DRZ400 all
  • Increased air flow over the stock air filter
  • Designed to increase horsepower and throttle response
  • Designed to fit inside the factory air box
  • Larger surface area over foam filters which offers longer service intervals in dusty conditions
  • Four layers of premium cotton gauze provides outstanding filtration
  • Washable & re-usable, never wears out
  • One filter will last the lifetime of your bike

$14.95

K&N Filter Care Kit


A six step maintenance system designed to recharge any K&N air filter

  • Completely restores airflow efficiency
  • Kit includes filter oil, and filter cleaner

$9.95

Nitrile gloves


Latex free gloves for the shop or garage. Package of 10 pairs of gloves.


$15.95

Extended Fuel Screw

DRZ400S

This extended fuel mixture screw makes it much easier to fine tune the idle mixture. This screw is made specifically for the stock OEM Suzuki carburetor. It's a nice addition to installing a jet kit or any other performance mods.


$41.95

Carburetor Repair Kit

DRZ400 S/SM Stock Carburetor

Repair kit comes with everything you need to get your carb back in shape.

Select model



Air Cutoff Valve Kit

DRZ400 Stock Carburetor

Quality air cutoff valve replacement kit contains parts necessary for a complete rebuild.


5/16" Fuel Filter


This filter is meant for 5/16" fuel lines. Only 1/2" thick once the fuel lines are in place, it is small enough to fit in just about anywhere.

 


Small Fuel Filters - 90 Degree or Straight


 

The small size and right angle hose barbs make it easier to fit into the small space between your fuel petcock and carburetor. Filter body is only 7/8" diameter. Straight filter is 2" long, 90 degree filter is only 1-5/8" long.


$39.95

Carburetor Overflow Canister


This canister by Pro Circuit allows you to move the overflow tubes from the carburetor up and out of the way. Universal application

Body

Back to Top

$359.95

Sargent Seat

(Made in USA) DRZ400 all

Sargent's proprietary seat foam is their own unique blend of resilience, firmness, and vibration-absorption qualities - making it well suited for maximum long distance comfort.

Please allow 1-2 weeks for delivery

! Seat orders ship Parcel Post (6-10 business days) within the US.  Why?





$174.95

Seat Concepts Foam & Cover Kit

(Made in USA) DRZ400 all

Seat Concepts dual-sport/adventure seat-kits incorporate a wider seating area for the rider, which results in more even weight distribution, while reducing pressure points.

Each kit contains instructions for easy "Do It Yourself" installation. This provides the highest level of quality & comfort at an affordable price.

Choose standard height or one inch lower than stock.

Click here to check out the new seat warmer insert.


$344.95

Moose Adventure Saddle

(Made in USA) DRZ400 all

Moose Racing now makes a seat for us DRZ riders. This is a complete seat already installed on a new seat pan. Take your old one off and put the new one on and get back to riding.

You must choose between the stock seat height or a low seat height (about 1 inch lower). Trouble touching the ground? Order the low seat, you will be glad you did.

  • Rugged micro-fiber suede top cover provides rider comfort and confidence
  • Side gripper panes keep you aboard during aggressive maneuvering
  • Smooth marine-grade vinyl with debossed Moose Racing logo
  • Comes with strap kit that enables you to confidently secure cargo to the pillion section of your seat

!  Seat orders ship Parcel Post Only. within the US. Why?

Choose Top Texture:


Choose Side Texture:



$332.95

Corbin Seat - Dualsport Riding Comfort

DRZ400 all

Corbin seats are custom made to order. You can choose your preferred texture for the top and sides of the seat. Please give us a call if you would like other color options or materials.

Corbin seats are carefully designed to provide a comfortable riding position. They are firm and supportive which allows you to ride all day without fatigue unlike the stock seat.

Corbin seats are built to order. Lead time on building a seat is 2-3 weeks.

The default vinyl choices are black 'carbon fiber' on top and 'asphalt' on the sides. You can view all of the available materials and colors on Corbin's Website.


!  Corbin seat orders ship Parcel Post Only. within the US. Why?

$22.95

Sit & Fly Net Seat Cover


Want to stay cool and comfy on those long summer rides? The Sit & Fly net seat cover allows air between you and the seat keeping things significantly cooler.

Allowing the air to circulate under you eliminates perspiration and keeps things dry and comfortable.

 
Optional Add on:


$39.95

Moose Seat Cover

(Made in USA) DRZ400 all

This is a high-quality seat cover done by Moose for the DRZ. This is a replacement cover only, no seat foam and you must install on your existing pan with existing foam.

  • Heavy duty marine grade vinyl
  • UV protected for long life
  • Double stitched for durability
  • Made in the USA

Click here to check out the new seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable.


$79.95

Moose Seat Warmer Kit


9" by 9" carbon fiber seat warmer that goes between your cover and the foam to keep your backside happy on those really cold days. This improved design produces 25% more heat than most other warmers using just 30 watts.

Kit includes the warming unit, with connector, 24" extension cable, rocker-type on/off switch and stub to splice into your wiring along with complete detailed instructions.


$69.95

Sheepskin Seat Cover

(Made in USA)

This is the secret for being able to put in those 500 mile days. Even a good touring seat can feel a bit firm after a couple hundred miles. Sheepskin gives that little bit of 'cush' and provides superior air circulation. Velcro straps allow easy removal when you don't need it. Measures 14" wide by 19" long.


$99.95

AirHawk Seat Cushion


So you're not ready to dish out $300 for a new seat but you can't stand to sit on the stocker for more than 50 miles. The Air Hawk might be the answer.

  • Air filled Airhawk 12"x18" cushion custom fits your shape and redistributes pressure that causes numbness and discomfort when you ride
  • Seat cushion cover is constructed of a breathable, stretchable Nylon/Lycra blend with a non skid Urethane base
  • Open mesh side panels allow heat to escape
  • Easily inflates by mouth with no pump needed
  • Mounting straps and Repair patch kit included
 

$29.95

Fender Brace


By popular demand - A stainless steel front fender brace. Helps stabilize your front fender. Gives additional strength for carrying a fender mounted tool bag. Fits on top of the fender and bolts between the fender and bottom triple clamp. Requires you to drill one hole in the fender for mounting. Stainless steel won't rust or corrode. Includes hardware.


$66.95

Frame Guards

(Made in USA) DRZ400E/S/SM
 

Give your DRZ that factory prepped look and protect your frame.

These frame guards from industry leaders Works Connection are CNC cut and formed from aircraft grade 5052 aluminum. These not only protect your frame from scuff and rub marks from your boots, but also give you a flatter surface for better grip and control with your lower legs. All the necessary mounting hardware is included making these a very simple bolt-on installation.

$19.95

Clear Headlight Guard

DRZ400 S & ES (Made in USA)

Made of military aircraft grade 3/16" cast acrylic, this guard will protect your lens from roost, rocks and branches. Optical clarity of the acrylic ensures brightness and projection of your headlight are minimally effected while all the while protecting your headlight from impact and abrasion.

Guards are held to the headlight lens with an industrial strength hook and loop system on each corner.


$57.95

Headlight Guard

(Made in USA) DRZ400 S & ES
 

Fabricated from mild steel and expanded metal and powdercoated black, this guard will protect the headlight from flying rocks and possible crash damage. Mounts to the same three mounting points as the headlight cowling and includes all required hardware. Light weight with limited reduction in light output.


$69.95

Front Disk & Fork Guard

DRZ400E/S
 

Protect your brake rotor and fork lowers from mud and debris. Choose Black or White.



New! 101315

JNS Engineering Side Stand Foot Pads

(Made in USA) DRZ400 All

A side stand foot pad will keep your bike upright when parked on soft terrain. Now available in two versions - a weld-on unit or a bolt-on unit that just requires a hole be drilled.

 
Choose Color


102215

Parabellum Rally Windscreen

DRZ400 S/SM (Made in USA)
click to enlarge

The Rally windscreen from Parabellum is the perfect protection from wind and debris without sacrificing technical off-road capabilities. This is an upright rally type windscreen that looks aggressive and performs well under all types of riding. Designed primarily for the off-road / dualsport enthusiast, this shield keeps pressure off the rider's chest while commuting from home to adventure and back.

Mounting is accomplished by drilling two holes on each side of your headlight cowl using the provided template. The shield is 14 inches tall, 11.5 inches wide at the bottom narrowing to 8.5 inches at the top. Made from military aircraft grade cast acrylic.

click to enlarge click to enlarge


$109.95

Bajaworx Rallye Windscreen

DRZ400S/SM (Made in USA)

Made specifically for the DR650 and DRZ400, this Rallye windscreen fits right against the cowling and directs the wind around the rider. Done in a mild tint, this windscreen will be a welcome addition to your DRZ.

Molded using a very durable, lightweight 1/8" thick polycarbonate - giving the windshield a high impact strength and making it shatter-resistant with a superior light transmission quality. Mounts quickly and easily onto the stock headlight cowling for a clean factory look. Drilling of the cowling is required, hardware is included. Removal for trail riding is also quick and easy.


$89.95

Laminar Lip Windscreen


The Laminar Lip 'B-King' windscreen. Easy attachment to your headlight shroud with 'Velcro-like' 3M Dual Locks. No drilling is required. The screen can be easily removed and replaced when needed. It's 15 inches wide and can be mounted to rise 7 to 10 inches higher than the top of the stock headlight shroud. Choose clear or smoke tinted. We include a nylon bolt kit should you wish to permanently mount your windscreen.

Optional Add on:

$129.95

Black Plastic Body Kit

DRZ400 E/S/SM

High-quality, direct replacement plastic kit includes:

  • Front and rear fender
  • Side covers
  • Air box cover
  • Radiator shrouds

!  Body kit orders ship Parcel Post Only. within the US. Why?

A slight modification is required for proper rear fender fitment on ES, S, and SM models.


$40.95

Black Side Panels

DRZ400 all

Black side panels, Quality parts from Acerbis. Replace those big white ones for a custom look.


$89.95

DSA Concepts Front Fender

(Made in USA) DRZ400E/S/SM

This is a new front fender made by DSA Concepts that is shaped very much like the OEM DRZ400SM front fender, but larger. Big enough to be functional in the wet and mud. Great look for the bike.


!  Front fender orders ship Parcel Post Only. within the US. Why?


$28.95

Supermoto Front Fender


Universal design. Vents in the back improve airflow to motor. Smaller front reduces 'wind steer' and improves high speed stability.


!  Front fender orders ship Parcel Post Only. within the US. Why?


$95.95

New! 071516

Suzuki Gray SM Fender

DRZ400

Genuine Suzuki super moto fender now available in the hard to find solid iron gray.

! Front fender orders ship Parcel Post (6-10 business days) within the US.  Why?


$259.95

IMS Fuel Tank

DRZ400 all

Get better range from your DRZ400 by adding an IMS fuel tank. Available in multiple color choices. Choose Natural if you wish to easily see the fuel level of your bike. 4.0 gallons.


!  Fuel tank orders ship Parcel Post Only. within the US. Why?


$239.95

Clarke Fuel Tank


More range at a great price. Choose the 3.6 gal tank for the off-road DRZ400E or 3.9 gal tank for the dual-sport DRZ400S. The 3.9 gal tank also fits the ES and SM models. Both tanks are available in a selection of colors.


$32.95

Locking Gas Cap


Security for your fuel tank. Includes 2 keys. Internally vented with a check valve that prevents spillage in case of a tip over. Fits Acerbis and IMS tanks.


$15.95

Replacement IMS Gas Cap


A replacement gas cap for your IMS tank. Newly redesigned to resist damage from new fuel additives that were hard on the seal in the old style cap.

$69.95

071516

Zeta CNC Gas Cap for Stock Tanks


This CNC cap will replace the stock gas cap on the stock tank. You do need some parts from the stock cap, so don't throw it away yet! It is not difficult and this kit includes the additional hardware required. Also included is a vent tube with a matching cap.

For use on STOCK TANK ONLY! This is NOT a locking cap.


$11.95

Fuel Tank Vent Cap


If you're like us, you hate the long floppy vent hose hanging off the cap of your aftermarket tank. This one-way vent cap replaces the long hose with a short one only about 2" long. It allows air into your tank but prevents fuel from sloshing out. Machined from billet alloy and anodized for good looks.

Not for stock fuel tanks


$24.95

'Raptor' Petcock


The famous 'Raptor' fuel valve. Replace your stock vacuum operated petcock with this manual one. Must be shut off any time the bike is parked for more than a few hours. Fits stock or aftermarket tanks. Plastic tanks may need the hole 'ovalized' to fit the dual standpipes.


$99.95

Devol Racing Radiator Guards

(Made in USA) DRZ400ES/S/SM '00-up

These radiator guards from Devol Racing protect your radiators from damage due to trail side objects and roost bullets. They offer protection not just from frontal assaults but also from those tricky side attacks. Made from high-grade aluminum alloy for light weight and strength, these guards have an improved air-flow design that eliminates any overheating problem. A solid mounting to the frame make these stronger than most guards that just mount to the radiators themselves.

Devol Racing makes a super product that will keep you on the trail for a long time.


$93.95

Skid Plate

(Made in USA) DRZ400E/S/SM
  • Made from strong and lightweight aircraft aluminum
  • Protects vital engine parts from rocks and debris
  • Custom fit to your specific bike model
  • Oil drain hole for easy access
  • All mounting hardware included

$159.95

Carbon Fiber Skid Plate

(Made in USA) DRZ400E/S/SM

The use of Kevlar gives this composite a longer fatigue life and greater tensile strength than aluminum. Composite plates will bounce back from hard hits and look great long after aluminum plates give up.

Drivetrain

Back to Top
Select Combination




Sprockets & Chain Packages

DRZ400 all

Complete chain and sprocket replacement packages.

  • JT steel sprockets
  • EK SR06 O-ring chain
Select Length


EK SR06 520 Chains


The SRO6 series chains offer a value-priced O-ring chain that will not compromise on quality or durability. Features include lightening holes, high-tech heat-treated steel alloys and all the exact same quality and craftsmanship that EK puts into their entire product line

Select Type:

520 Master Links

DRZ400 all

Always carry a spare master link when out on the trail.


Important! Master links are not interchangeable. Be sure to get the manufacturer and series off your current chain.


$21.95

EK SRO6 520 Chain Extension Kit


Adding a larger front or rear sprocket may require a few extra links in your chain. If you are running the EK SRO6 520 O-ring chain, our extension kit is an affordable way to do it.


$8.95

Motul C5 Chain Paste


 

A new innovative product from Motul. This chain lube comes in a brush applicator squeeze-tube bottle. It makes applying chain lube easy and less messy than spray on lubes. Chain Paste is easy to carry with you on those long trips.


$43.95

Moose Racing Chain Guide

DRZ400 All  (Made in USA)

Aircraft aluminum withstands hard hits from logs and rocks. All mounting hardware and wear blocks included.

Choose Package:


Scottoiler Vacuum Auto Chain Oiling System


This is a vacuum operated automatic chain oiling system to keep your driveline adequately lubricated at all times.

When properly adjusted the oil will last thousands of miles between refills. The Scottoiler kit includes one 250ml bottler of oil which is good for 10000 miles of riding.

$12.95

030816

360° Chain Brush


This brush has 2.25 coils of 360° chemical-resistant nylon bristles to make it the fastest, most effective, precise and systematic method for giving your chain a thorough cleaning. It will help the performance of the chain, the sprockets and the engine. This brush will fit any 400 or 500 series chains.


$19.95

Master Link Pliers


Make your life a little easier by having a set of these in your toolbox. Designed to simplify installation and removal of clip-type master links. One tip is shorter and notched to be placed on the pin which allows the longer end to push the clip.


$17.00 - $23.00

Countershaft Sprockets

DRZ400 all

High quality steel front sprockets from 11 teeth to 16 teeth.

! The 16T sprocket will require a small amount of grinding inside the sprocket cover for clearance.


$33.95 - $44.95

Rear Sprockets

DRZ400 all

High quality steel rear sprockets from 39 teeth to 53 teeth.


$10.95

Sprocket bolts

DRZ400 all

A set of six high-quality, grade 10 sprocket bolts with locknuts. Threadlock compound has also been pre-applied for extra security.


$4.95

Lock-Nut Style Rear Axle Nut

DRZ400 all

The 2006 and newer DR650 did away with the cotter pin on the rear axle and uses only a locknut. This is a nice upgrade for the DRZ400. You can avoid having to keep new replacement cotter pins on hand every time you adjust your chain.


$8.95

Renthal Chain Lube


Renthal chain lube is 100% lubricant, zero propellant. So this new 250ml bottle size combines high performance and value.

The all-new formula Chain Lube is specially designed to penetrate all parts of the chain. This all-condition lube is compatible with all o-ring and non o-ring chains.

Select color





$69.95

MSRHP Complete Chain Guide

DRZ400 All  (Made in USA)

MSRHP chain guides replace the OEM assembly at a fraction of the cost. The plastic composition is made to absorb impacts and not bend like aluminum OEM guides. The inner block design and compound is much more durable than OEM but maintains sound dampening characteristics


$15.95

Ball Bearing Chain Rollers

DRZ400 All  (Made in USA)

Replace your chain rollers with these quality rollers with 2 sealed ball bearings. The stock rollers have no bearings, just a plastic wheel riding on a bolt. Ball bearing chain rollers reduce friction, are smoother, quieter and last longer.


$13.95

The Grunge Brush


Innovative design that cleans chain from 3 angles at once. Long handle keeps fingers and hands away from chain and sprockets.

  • Will not harm O-ring chains
  • Easily adjustable for all chain sizes

$16.95

Chain Breaker Tool


Here is a tool to help you remove a few links from a chain that is too long to fit your bike. A great tool to have in your tool box.

Suspension

Back to Top

$129.95

Fork Springs

DRZ400 E/S

A pair of Race Tech fork springs to dial in your front suspension to suit your weight.

Fits all DRZ400 models with conventional forks (not for SM)

Recommended spring rates:


Rider Weight w/gear lbs. Spring Rate
90 or less .42
90-119 .44 (stock)
120-150 .46
150-180 .48
180-220 .50
220-250 .52
250+ .54

$159.95

Race Tech Gold Valve - Rear Shock

DRZ400 E/S/SM all

The Race Tech Gold Valve allows you to tune both compression and rebound valving for vastly improved performance.

  • Bolt-on shock valving for riders serious about suspension performance
  • Improves control, traction, plushness and bottoming resistance
  • Improved, long-wearing, low-friction sealing design decreases fade
  • Includes complete instructions

$155.95

Race Tech Fork Cartridge Emulators

DRZ400 2000-2001

Emulators make damping rod forks perform like well-tuned cartridge forks. Emulators are tunable valves that sit inside your forks on top of the damping rods and are held in place by the fork springs. Simple to install and completely tunable for all conditions and rider preferences.


$155.95

Race Tech Gold Valves - Front Forks

DRZ400E/S 02-up
  • Race Tech's original bolt-on fork valving system for front cartridge forks
  • Triple the flow area of pistons
  • Put valving control on the shim stack
  • Outstanding tunability; improved control, traction, plushness and bottoming resistance
  • Complete instructions, Gold Valve pistons, valving charts, valving shims and "Technical Edge
  • Fork Maintenance and Gold Valve Installation" video all included

$37.95

Shock Seal Head Kit

DRZ400 all

For a top notch rebuild or re-valve of your rear shock use this high quality replacement seal head.

  • Complete assembly, ready to install into the shock body
  • Has air bleed holes to help remove air from the oil reservoir during installation
  • Double-lip oil seal design keeps out dirt and keeps friction low
  • Kits include aluminum body, dust seal, bushing, oil seal, O-ring, internal guide bushing/washer, snap ring, and top-out bumper

$25.95

Shock Bumper

DRZ400 All
click to enlarge

Heavy duty shock bumper. The stock bumper is prone to disintegrating with age. If you are re-valving your shock it's a good idea to be sure the bumper is in good shape.


$19.95

Fork Seal Skins

Sold in pairs
 

Helps protect vulnerable fork tube and seal from dust, dirt, and corrosive elements. Hook & loop (velcro) fastening on back side makes installation or removal for cleaning a breeze.

 

$29.95

>Fork Boots

Sold in pairs

An excellent replacement for the stock fork boots. These are great for protection from dirt, rocks and other contaminants. These boots utilize the latest advances in material technology to adapt to fork and styling demands. These high quality fork boots are 1/4 the price of the OEM factory replacements.

Choose black, blue, red or yellow.


$34.99

Race Tech's Motorcycle Suspension Bible

(Made in USA)

Based on the wildly popular Race Tech Suspension Seminars taught by Paul Thede around the world, this step-by-step guide shows riders how to make their bikes handle like the pros. Thede gives the lowdown on all types of suspension, including cartridge and non-cartridge forks as well as dual-chamber and nitrogen-charged shocks.

The three forces of suspension, testing procedures, even the black arts of chassis geometry: Thede explains it all. The book provides step-by-step photos of suspension disassembly and assembly as well as a detailed troubleshooting guide for dirt, street and track.


$109.95

Shock Spring

DRZ400 all

Race Tech shock springs in a wide range of spring rates to dial in your rear suspension to suit your weight (stock spring is 5.3 kg/nm). Recommended spring rates:


Rider Weight w/gear lbs. Spring Rate
100 or less 4.6
100-124 4.8
125-149 5.0
150-174 5.2
175-199 5.4
200-224 5.7
225-274 6.0
275 + 6.3

$63.95

Linkage Bearing Kit

DRZ400 all

Complete high quality kit to replace the bearing and seals in the DRZ400 shock linkage. Includes the lower shock bearing.


$59.95

Swingarm Bearing Kit

DRZ400 all

Complete high quality kit to replace the bearing and seals in the DRZ400 swingarm pivot.


$39.95

Steering Head Bearing Kit

DRZ400 all
  • A set of high quality replacement steering stem bearings
  • Tapered roller bearings provide decreased maintenance along with less wear, smoother operation and longer life
  • Kit comes complete with both upper and lower taper bearing cups, cones, and most include top and bottom seals

$29.95

Fork Seal with Dust Seal kit


Low friction 'triple lip' seal design. Oil seals last 3-4 times longer that OEM seals. Kit includes Fork Seals and dust wipers.


$44.95

New! 123114

49mm Fork Seal Driver

DRZ400S/E

Innovative design makes tool easier and more secure to use than old fashioned pin-aligned drivers

  • Knurled anodized aluminum locking ring
  • Perfectly weighted to drive seals
  • Carbon steel body halves

$99.95

Lowering Links

(Made in USA) DRZ400 all

Billet aluminum lowering links. Lowers the rear suspension 1" or 1.75"


$159.95

SuperBrace Fork Brace

DRZ400 E/S '01-Current

SuperBrace is the leading motorcycle fork stabilizer. This patented brace provides better stability, superior aerodynamics and a more streamlined look than other multi-piece braces on the market.

  • Reduces low and high speed wobbles
  • Improves stability in tight cornering
  • Improves tire life and reduces cupping
  • Decreases sensitivity to rough road surfaces and rain grooves
  • Each SuperBrace is designed and manufactured for each specific motorcycle and made of 6061-T6 aircraft aluminum
  • Ten minute easy installation

! Does not fit the DRZ400 SM SuperMoto


$19.95

New! 031815

Fork Oil Level Gauge


Having the proper fork oil level is imperative to the handling of your bike. Setting the correct fork oil level is a snap with this fully adjustable gauge. The adjustable aluminum level plate can be set from 0 to 295mm. The oil reservoir has single milliliter markings up to 60ml.

Being able to accurately tune your forks by adjusting the oil level can make them better resist brake dive or bottoming. Oil level should be thought of as a fine tuning method to make your choice of spring rate work perfectly for your bike.

Lighting & Electrical

Back to Top

$89.95 or $109.95

Taillight and License Plate Bracket

DRZ400 S/ES/SM all

Lose that ugly stock taillight and license plate bracket and install this tidy one from ProCycle. We designed this unit and have it manufactured here in Oregon. Kit includes a LED taillight / brake light unit as well as compact turnsignals. We also include splice connectors and split tubing, everything you need for this installation. The taillight has a cool looking clear lens which lights up red when powered up.

There is also an option to include matching front turn signals with side mount brackets that allow you to replace the clunky front signals with the same style as the rear in this kit.

  
Choose Package:


Micro-Start Portable Jump Start and Power Supply




A device that you can keep in your fanny-pack, backpack or even pocket that can jump-start your motorcycle or car. It can also charge your cell phone, GPS unit, laptop or other electronic devices.

  • XP-1 is 6" x 2 7/8" x1" 14oz.
  • XP-3 is 5" x 2 7/8" x 1" 12oz.
  • Holds a charge for up to a year.

Review by Dirt Wheels Magazine

XP-1:
  • 200 Amp- 400 Peak Amp
  • 12000 mah Capacity
  • 19V Output Port for Laptops
  • 12V Standard Output Port
  • 5V 2A USB Port
  • Detachable Mini Jumper Clamps
  • 3 power ports: 19v for lap tops, 12v standard output, and a USB 5v output for USB powered devices
  • A Universal Cable with 8 different detachable tips to fit all the different brands of Laptop charging ports (Apple, Acer, Dell, HP, Asus, and more)
  • A Universal Cable for 12v standard plug accessories such as Mobile DVD players and heated gear. (8amp max)
  • A Universal USB Cable with 4 of the most common connectors (iPhone, Lightning, micro USB, mini USB) for portable Electronics such as Cell Phones, iPads, iReaders (Kindles), PSPs, GPS, tablet computers, and anything else using the 5V USB standard
  • 1 Home Charger (to charge the XP-1)
  • 1 Mobile Charger for plugging into cigarette lighter socket (to charge XP-1)
  • Nylon zippered carrying case
XP-3:
  • 200 Amp- 400 Peak Amp
  • 8000mah
  • 5V 2a USB Port
  • Micro-Start XP-3 Unit
  • Detachable Mini Jumper Clamps
  • A Universal USB Cable with 4 of the most common connectors (iPhone, Lightning, micro USB, mini USB) for portable Electronics such as Cell Phones, iPads, iReaders (Kindles), PSPs, GPS, tablet computers, and anything else using the 5V USB standard
  • 1 Home Charger (to charge the XP-3)
  • 1 Mobile Charger for plugging into cigarette lighter socket (to charge XP-3)
  • Nylon zippered carrying case

$18.95

LED Taillight/Brake Light Bulb (1157 Type)


A LED Taillight/Brake Light bulb uses considerably less energy than a standard filament type bulb. LED brake light will draw approximately 1 watt while a filament type draws in excess of 15 watts. This means less power draw from batteries on total loss systems and additional power for accessories on regular systems.


$64.95

New! 012715

3800 Lumen LED Headlight Bulb


New and improved. Brighter (3800 Lumens), better low/high beam contrast, smaller, lower Kelvin color temperature (5500K), replaceable drivers and easier to install. All of these features and the most reliable LED bulb currently available. It only draws 20 watts.

This bulb fits H4 bases only, has Cree XML2 emitters and is fan cooled for extreme conditions. Further features include vibration proof and water-resistance, even complete submersion.


$79.95

High/Low H4 HID Light Kit

DRZ400 all street models

More light - Less power. Only draws 35 watts yet puts out several times as much light as the stock 55 watt halogen bulb. The HID is for the riders who want the best but don't want to break the bank getting it. Operates on both high or low beam. The kit comes complete with a high/low single capsule HID bulb, slim profile ballast, wiring extenders, and all the hardware you need to install the kit. Click the pics below for more info. 'S' models only.


H4 high beam

HID high beam

$16.95

Heavy Duty 12V H4 Bulb

DRZ400 all street models

This is a standard H4 bulb that has an 80 watt low beam and a 100 watt high beam. This is an easy lighting upgrade that should not over tax a stock charging system.

Optional Add on:


$29.95

"Crash Advantage" LED Turn Signals

Sold in pairs

These bright LED turn signals will bend more than 90 degrees without damage. Only 2 1/2" long.

LED turn signals require a resistor kit on the DRZ400. Diode kit is required for bikes with a single turn signal indicator on the dash.


$29.90

Mini Turn Signals

4 Pack

These signals have short rubberized flexible stems and bright mini halogen bulbs.

Choose Kit:


Trail Tech Equinox 60mm LED Light



Trail Tech's 60mm LEDs are perfect for any riding adventure, no matter the conditions. Throwing out over 1,000 lumens brightness at only 10 watts, it is one of the most efficient lights on the market.

Three power modes allow performance at any circumstance, from Hi mode for lighting up the night to Low mode for daytime driving light.

The anodized billet aluminum housing is durable and promotes better heat management. Aluminum reflector with vacuum metal deposition creates the most accurate spot beam.


$119.95

VisionX Solstice 10 Watt LED Light


Each 10 watt Solstice Solo produces 900 lumens. Roughly equal to a 50 watt halogen bulb. These are the brightest LED off road lamps on the market. The rugged and compact 2" x 2" square die-cast aluminum housing makes mounting easy. The Solstice Solo also features a 4 sided channel design that allows you to interlink it on all four sides with another Solstice Solo pod. Includes stainless steel mounting bracket and waterproof connection. The Elliptical pattern is wide and flat. Sold each.

Select Mount Type:



New! 102113

JNS Auxiliary Light Mounts

DRZ400 S/ES/SM all

These heavy-duty aluminum brackets are laser cut from 0.190" 5052 Aluminum then powdercoated black for good looks and protection. Designed specifically for mounting auxiliary lights to the front of your DRZ400, the mount goes between the fender and the lower triple clamp. Longer fender bolts are included in each kit. installs in 10 minutes and is powdercoated black for good looks and protection.

Three options are available: two different dual mounts that place the lights outside the fender and a single, center type mount. The 2" mount is for smaller type lights and is 8-5/8" between the mounting holes while the 3" is 10-3/8" between the mounting holes. If you are going to use larger style lights, the 3" mount is for you.

click to enlarge click to enlarge click to enlarge click to enlarge

$14.95

USB Device Charger


This mini USB device connects to a battery cable with a SAE connector just like the typical Battery Tender outlet and allows you to charge your iPad, iPod, iPhone, GPS unit, camera or Smart phone. Input is 12 Volts, output to the USB port is 2.1A maximum, perfect for your phone or low or other USB devices.


LCD Digital Voltmeter-Quick Disconnect


Deltran quick-disconnect plug with LCD voltmeter display. Plug this into your Battery Tender, or any SAE cable, to see a LCD display of the battery voltage. Three LED lights indicate the state of charge as well. Easily unplug it whenever you need to get the charger hooked back up.

Choose Package:


12V LED Flashlight/Charging System Indicator

DRZ400 S/ES/SM all

This great little 6-LED flashlight goes right into your Battery Tender type plug for hours of light. In addition, it has a charging system check that lets you know if your bike is charging properly. All with a 40 inch cord so you can see in those out of the way places when you need to.

Don't have a cable from your battery? Well, select the package and we will include a cable that goes from your battery to a SAE type connector to plug in your light or charge your battery when at home. This is a fused circuit to protect your battery.


$49.95

Digital Voltmeter and Bracket


A digital voltmeter that can be mounted almost anywhere thanks to our multi-position stainless steel bracket. This will tell you how your charging system is doing and whether or not you need to turn off the laptop and in-flight movie system for awhile. Completely waterproof and comes with connectors, wires and thorough instructions. We consider this a 'must have' device for riders who use heated riding gear, heated grips, additional lighting, etc.

image image

$149.95

Shorai Power Lithium-Iron Battery


  • No more dead batteries. Holds charge for one year without maintenance
  • Two to four times the life of lead-acid batteries
  • Carbon Fiber Composite Case
  • Faster cranking for better starts
  • Environmentally friendly, just discharge and dispose
  • Ultra light and compact - You could easily carry a spare!

LFX14 measures 4.5" x 3.5" x 2.25", weighs 1 lb 10 oz and is rated at 210 cranking amps. For reference the stock YT7B-BS weighs 6 lb and is rated at just 120 cranking amps. Each Shorai battery includes self adhesive foam panels to achieve a snug fit in your battery box.


$76.95

Shorai Charger


You can charge your Shorai battery with a regular battery charger but if you want the very best for it, this charger is designed for optimum performance by balancing the individual cells in the battery. Balanced charging ensures the battery reaches its fullest capacity and longest life. 'Store' mode allows long term long term maintenance storage.

Shorai Charge/Store Dedicated Battery Management System for Shorai LFX only. 2A Max charge rate, connects via BMS 5-pin port on LFX batteries. Includes modes for full charge, or long-term storage. Input USA 110~120V 50/60 Hz.

For Shorai Lithium Iron batteries only.


$36.95

Battery Tender Jr. 12V Charger


  • Fully automatic two-stage lead-acid battery charger
  • Lightweight, compact size is ideal for those hard-to-reach spots
  • Trickle charger ensures batteries are maintained after charging and always ready to go
  • Ideal for all lead-acid, sealed maintenance-free and gel cell batteries (not recommended for lithium iron batteries such as the Shorai)
  • After full 14.4VDC charge is reached, converts to float charger and monitors battery at 13.2VDC; when voltage drops below 12.6VDC, charger resumes charging back to 14.4VDC
  • Two-color LED indicator (red light = charging; green light = storage)
  • Spark-proof
  • Reverse-polarity protected
  • 12' output cord and quick-connect harness

$37.95

New! 032116

Brake Light Modulator

(Made in USA)

This compact, solid state electronic module converts your ordinary brake light into an attention getting, visual alerting device.

Module causes three short flashes and then stays solid for 3.5 sec, then repeats the cycle for as long the brake is on.

! Not for integrated brake/turn units. Resistor Kit may be required if using an LED bulb.

$109.95

New! 051116

signalMinder


click to enlarge

The signalMinder unit is designed as a plug-in replacement for many Japanese bikes. This unit will automatically cancel your turn signal if you forget to shut it off.

  • Cancels signal at 10, 20 or 30 second intervals
  • Allows you to use turn signals as running lights
  • 4-way hazzard option
  • Brake flash option

SM-3 unit is designed as a plug-in replacement for most Honda and some newer European bikes. signalMinder uses a computer chip to cancel the turn signals. There are three selectable timeouts; 10, 20, 30 seconds.

RUNNING LIGHT OPTION: By attaching two quick-connect wires included, you can convert ALL FOUR turn signals to running lights and establish a dual-channel system on your bike.

Special Note! For 2009 and up Kawasaki models that have onboard computer diagnostics, or if you have Alarm system that activates turn signals, please select SN-4D harness shown below.

Using the DIP Switch #1, you can keep them off and still have the dual-channel system. With the dual-channel system, when you activate the RIGHT turn signal three times in succession, you get 4-way hazard flash function.

BRAKE FLASH OPTION: will flash the turn signal lamps every time you apply brakes. A short 2 second flash pattern begins with quick flashes then slows down to stay on solid.

BRAKE OVERRIDE OPTION suspends the time-out feature until the brakes are released. This allows continued flashing for those times when you are waiting at the signals to make a turn and do not want the time-out to cancel the flashing.

Choose Package:

New! 082715

Koso Mini 3 Temp/Clock/Volt Gauge


click to enlarge
click to enlarge

This Mini 3 meter was designed to help you monitor basic information before and during a ride. Check the condition of the battery before leaving and the voltage of your system during the ride. The ambient temperature function will give you a good reference about how to dress prior to and what is happening during your trip. It can be very handy to know if the temperature is near or below freezing. The large clock makes it easy to know if you are on schedule or not.

Dimensions: 2.4" W x 1.2" H x .5" D.

Available for the Mini 3 is a nicely crafted mounting plate that allows you to place your new gauge wherever you like.

Include Power Port:


Select Charging Cable:


New! 032516

Weatherproof USB Charging System


click to enlarge

This compact, easy to mount, all weather USB Power Port is the answer for powering and charging your USB devices including cell phones, smart phones, most GPS units, MP3 players and some digital cameras.

Power port connects from battery to handlebars using included universal mount.

Select the correct charging cable for your application by clicking on "More Information".

click to enlarge click to enlarge
  • 18" power port and charging cables
  • Input Voltage: 12V ± 4.0V
  • Output Voltage: 5V ±.25V
  • Output Current: 1A Max
  • 3BR Powersports Universal Mounting System
  • Powers Garmin GPS as well as most cell phones and any other device that charges using 1A or less of USB power

Red Band USB Smart phone Quick-Charge Cables (Micro style connector)looks like standard USB data cables but have the built-in ability to signal Smart phones such as Android or Windows to charge at full rate when plugged into any "dumb" charger such as car chargers, wall adapters or 3BR Powersports TAPP series of all-weather USB power ports. Charging at full rate can reduce the charging time by as much as two hours and will easily keep up with power hungry applications such as GPS or video.

Red Band GPS Power cables (Mini style connector) enable Garmin Nuvi GPS to navigate when plugged into a generic USB power port. Garmin Nuvi uses the cable to determine which mode, navigate or data, the GPS should be operating in. Using a standard USB data cable to power a Garmin Nuvi will cause it to go into data mode for transferring maps, route/track data, pictures etc. The Garmin factory power cable is used to enable navigation mode. However, the Garmin power cable is unsatisfactory for powersports applications as it is not weatherproof, is way too long and is only supplied with a cigarette lighter-type of plug. The 3BR Powersports Red Band GPS power cable looks like a standard USB power cable with a USB Type A plug on the source end but it has internal circuitry to make it appear to the GPS as a Garmin power cable. The USB Type A plug allows powering the GPS from any generic USB port and allows use of 3BR Powersports power port cables for full all-weather protection.


$21.95

Headlight Adjusters

DRZ400 S/ES/SM all
click to enlarge
 click to enlarge

We make these thumb-screws to replace the stock headlight adjustment screws. When you are loading the bike up for a long trip or swapping out your dirt wheels for the motard setup your headlight aim changes. These adjusters make it much easier to keep your headlight aimed properly. This is even more important if you are running the HID headlight as it is very easy to dazzle oncoming traffic if your headlight isn't aimed correctly.

Sold in pairs.



RAM Light Mounts

For LED Auxiliary Lights

The perfect solution for mounting those LED auxiliary lights. The base of the RAM mount is held by your mirror. This puts the light where you can easily adjust the angle for different riding situations. We have 2 types to choose from. The Equinox mount fits Trail Tech Equinox lights or any other light with a 10mm or 3/8" mounting stud. The Solstice mount fits VisionX Solstice lights or any other light with a 6mm or 1/4" hole in the mounting bracket.

Sold individually.

  

$139.95

High Output 200 Watt Stator

DRZ400 S/ES/SM all

This high output stator will allow you to run brighter lights, heated gear, heated grips, etc.


$99.95

Voltage Regulator

DRZ400 S/ES/SM all

Heavy duty replacement voltage regulator. More robust but lower cost than the factory unit.

Select Mount Type:


$49.95

New! 101515

RAM Cell Phone Mount


A complete kit to mount your phone (or other electronic device) to your motorcycle. The cradle expands from 2.25" to 3.25" wide and 4.75" to 6.25" tall. The width is adjustable but fixed while the upper portion of the cradle is spring loaded to keep your device secured in the roughest conditions.

Select the mount option that works best for you. The mirror mount is shown in the photo at left and is a flat plate with an 11mm hole on one side and a RAM ball on the other. Simply remove your mirror, place the plate between your mirror and the perch and tighten it down.

The handlebar mount kit allows you to mount to either a 7/8" or 1-1/8" bar. Also includes hardware to mount to the back of a lever perch. See image at bottom right for kit pieces.

click to enlarge click to enlarge click to enlarge

$34.95

New! 101515

Noise Isolating Earbuds


click to enlarge

These lightweight ear buds function just like any other set of ear buds, yet make a much better, and more comfortable seal, which helps put the music (or phone, GPS, intercom, etc) where it matters most. The unique earplug design ensures that wind and engine noise is blocked and more sound from your audio device is channeled straight to your ear. They give you a 25dB sound reduction. Save your hearing and hear your tunes.

The low profile allows them to easily fit under your helmet, giving you ear plugs as well as speakers. Total length of wire is 44", enough to reach just about anywhere you need.


$14.95

ThumbDogs


click to enlarge

These simple add-ons stretch and grip to the finger of your favorite glove using Grrprr technology. Users can operate a phone or any touch screen device and never have to remove their nice warm gloves.

A special conductive material enables you to interact with capacitive touch screens quickly and easily. There are two ThumbDogs to each package so you can double digit type just like you would in the real world. You can also put one on your index finger to operate your GPS.

Wheels

Back to Top
Select Rims:



Select Hubs:

Warp 9 Billet Hubs:


Optional Add Ons:

$1499.00

ProCycle Supermoto Wheel Set

DRZ400 all

We start with Excel Takasago, or top of the line Sun rims, OEM hubs and Buchanan's heavy gauge stainless steel spokes. Rims and spokes are then precision machined for a perfect match to your bike.

Our pro shop then laces and trues your wheels to perfection, giving you the highest quality set of custom wheels available.

  • New OEM hubs with bearings and seals installed
  • Excel or Sun 3.5" x 17" front rim
  • Excel or Sun 4.25" x 17" rear rim
  • Buchanan's stainless steel heavy gauge spokes and zinc-plated nipples

Want your wheels to be extra special? How about CNC machined and anodized hubs from Warp 9 for that top of the line look. Warp 9 hubs are just $49 extra and come in a variety of colors listed at right.

Add any set of SM tires to your order and we will mount and balance for free! Tubes and rim strips included.

Wheels are custom made to order and cannot be canceled. Please allow 2-3 weeks for delivery.

Select Rims:



Select Hubs:

Warp 9 Billet Hubs:


Optional Add Ons:

$1399.00

ProCycle ADVENTURE Wheels


Complete set of 'Adventure' wheels. These are the same rim sizes as used by the BMW GS and other big adventure bikes. The 19" front and wide 17" rear will give you great twisty road handling on the pavement while still being dual-sport friendly.

We start with Excel Takasago, or top of the line Sun rims, OEM hubs and Buchanan's heavy gauge stainless steel spokes. Rims and spokes are precision machined for a perfect match to your bike.

Our pro shop then laces and trues your wheels to perfection, giving you the highest quality set of custom wheels available.

  • New OEM hubs
  • Excel 2.5" or Sun 2.75" x 19" front rim
  • Excel or Sun 4.25" x 17" rear rim
  • Buchanan's stainless steel heavy gauge spokes and zinc-plated nipples

Want the coolest DRZ ADV wheels? How about CNC machined and anodized hubs from Warp 9 for that top of the line look. Warp 9 hubs are just $49 extra and come in a variety of colors listed at right.

Add any set of ADV Tires to your order and we will mount and balance for free! Tubes and rim strips included.

Wheels are custom made to order and cannot be canceled. Please allow 2-3 weeks for delivery.

Select Rims:



Select Hubs:

Warp 9 Billet Hubs:


Optional Add Ons:

$1299.00

Off-Road Wheels for your SuperMoto

DRZ400SM all

Complete 'Off Road' wheels for your DRZ Supermoto. We custom build our wheels to fit your bike.

Our supermoto wheels are built on OEM hubs for maximum compatibility with your bike. Stock hubs allow you to use the rotors and sprockets built for your bike instead of expensive and difficult to obtain parts for aftermarket hubs.

Our Off-Road wheels are carefully laced and trued to provide you with a solid, high-quality wheel. We use high quality Excel rims and Buchanan's heavy gauge spokes and heavy-duty nipples. All bearings and seals come pre-installed.

  • New OEM factory hubs
  • Excel 1.85"x21" front rim, clear-anodized aluminum
  • Excel 2.5"x18" rear rim, clear-anodized aluminum
  • Buchanan's stainless steel heavy gauge spokes with plated nipples

Yep, we can build these wheels around a sexy set of Warp 9 hubs too. Just select your colors and we will get them moving.

! All our wheels are custom built to order, please allow 2-3 weeks for delivery. Once ordered, custom wheels, rims or spokes cannot be cancelled or returned.




Wheel Bearing Kits


Quality replacement bearings and seals from Moose Racing. All bearings are sealed on both sides.

Tires & Tubes

Back to Top

Select items







Shinko 705


The 705 Series are DOT approved dual sport tires designed for 75% street and 25% trail riding. An aggressive tread pattern provides excellent wet and dry weather adhesion and the compound resists tearing while riding off road.

Select items




Kenda K761


Kenda's newest dual-sport tire designed for the 80% on-road, 20% off-road crowd.

  • DOT approved
  • Unique combination of street and off-road grip provides maximum performance
  • Strong and durable nylon four-ply construction
  • The advanced compound design gives better stability, corning traction and braking control
  • Tube type tire H-rated for speeds up to 130 mph

Select items




Pirelli MT21 Rallycross


This street-legal knobby from Pirelli has good stability and cornering precision thanks to the carcass stiffness. The tread pattern optimized for use on dirt and gravel roads, cross-country racing and desert tours. It has lasting off-road performance and knob tearing resistance due to the special off-road compound.

Select items




Michelin T63


  • Tread pattern derived from Michelins highly successful desert tires, for exceptional traction off road
  • Excellent stability and durability
  • High level of grip on the road
  • Reinforced knobs resist tearing and abrasion on asphalt
  • "S" speed rated for highway use

$36.95

Smart Caps


Ride-On offers riders a first-class Tire Pressure Monitoring System known as an LED Smart Cap. The Smart Cap TPMS is an LED tire pressure monitoring device for your bike. It is easy to install and automatically calibrates to the pressure of each individual tire. A blinking red light on the Smart Cap indicates a loss of 4 PSI or more. A yellow light indicates the battery is running low.

If you purchase a 2-pack motorcycle kit you will enjoy FREE Ride-On LED Smart Cap Roadside Assistance (for public roads only). You will find detailed information on this free service on Ride-On's website. Click here to read more from their website.


$8.95

Rim Protectors

Sold in pairs

Protect your wheels from scratches and dings caused by tire changing tools

Includes retrieval cord for easy use


$29.95

Tire Bead Breaker


Changing tubes or tires without the right tools can be a real chore. Don't fight your snug beads any longer, use this 27" long tool that opens to 7-3/4" to provide the leverage you need to easily break your tire bead. Constructed from heavy-duty steel with comfortable no-slip grips, this tool makes the job a snap.


$17.95

Warp 9 Valve Stem Puller Tool



This ultra-cool little tool is used to pull the valve stem through the hole on motorcycle rims saving your finger tips when changing tires, fixing flats or any time the tube has to come out of the rim. It threads inside the valve stem making it easier to pull through the rim hole. You can use it as a valve stem puller, valve core removal tool or a tire deflator.

Handle is CNC machined and has a threaded hole in each end, one to hold and protect the threaded end of the tool and one for a spare valve core (not included). Anodized blue for good looks and corrosion resistance.

Select items




Dunlop 606 DOT Knobby


Dunlop designed the D606 tire to be street-legal but with an emphasis on aggressive off-road riding and great durability. A full-depth tread pattern designed for rigorous off-road use yields excellent traction on everything from hard-packed fire roads to soft single-track trails. At the same time, the D606's tread compound is engineered for good highway durability and grip.

Select items







Continental TKC 80


The TKC80 has a self-cleaning tread pattern along with high levels of side stability on soft surfaces with very good road handling manners. It is also original equipment on BMW 1200 GS Adventure and KTM 690 Enduro R.

Standard Duty Tubes







Heavy Duty Tubes






Rim Strips






Motorcycle Tubes & Rim Strips




High quality tubes made of a blend of natural and butyl rubber meet or exceed OEM quality standards.

The heavy duty tubes are 3mm thick and puncture resistant

New tires and tubes deserve new rim strips. Choose the correct size for your machine and toss the old cracked and broken ones. For 19" rims, please order the 18" rim strip. It will fit just fine.

Be sure and order the 3.0" wide strip ONLY if you have supermoto rims. This is a 16" strip that will fit your SM rims perfectly.

$44.95

MotoPressor Pocket Pump


The MotoPressor is a compact pump unit that weighs only 1.5 pounds and fits in the palm of your hand. MotoPressor very cleverly omitted the plastic housing you find on other pumps. This makes it smaller and easier to carry with you. Included is a 25 inch long inflator hose, with a hands-free lock-down delivery valve. You also get a SAE power cord that attaches to your battery and stays there. The Pocket Pump has an 8.5 foot cord to give your air supply plenty of reach. All this packs into a heavy duty neoprene pouch.

MotoPressor will pump the front or rear tire of your motorcycle from flat to approximately 30 psi in 2 minutes and is capable of pumping to over 100 psi. Use it to inflate tires, top off your air shocks, air forks, inflate air beds or anything else.

If you will use the MotoPressor on a CANbus BMW please click on the More Information button.

! Do not use this pump in a standard BMW accessory outlet, unless it is wired directly to the battery and bypasses the motorcycle's electrical CANbus system. The CANbus monitors and limits the amperage of the accessory outlet. When you plug the MotoPressor into a CANbus equipped accessory outlet the CANbus will automatically shut off the circuit and the MotoPressor will stop working. It is not the fault of the Motopressor.

If you have a CANbus equipped bike and you are not SURE about using the accessory outlet, use the alligator clips to get power from your battery or better still connect the supplied SAE terminal connectors to your battery and get power from there.


$33.95

Mini Air Compressor


Portable 12v compressor is perfect for any tool kit. This unit weighs in at only 14oz and measures just 4"x2"x6".

Features a built in LED light and 0-120 psi gauge

• Comes with everything shown


$17.95

Tirepro Digital Tire Gauge


  • Large display, readings are shown to 0.1 psi
  • Kpa and Kg-cm2 scales also provided
  • Reads up to 99 psi
  • Ergonomic shape fits nicely in your hand

$10.95

8-1/2 inch Tire Irons


Here is a set of 'trail size' tire irons. At 8-1/2 inches long they are small enough to fit in a fender bag with your spare tube.

$59.95

"Tread Doctor" Knobby Cutting Tool


Refresh your front or rear tire instead of throwing them out! Tread Doctor Lightweight heated tool lets you quickly cut new edges into your dull worn out knobby tires.


$35.95

Mini-Morph Pump


The Mini-Morph is actually a bicycle pump, but is probably the best compact pump we have found for adventure / dual-sport riding. It has a fold-out foot and handle as well as a 4 inch hose so you can set it on the ground to pump. At only 10" long, it is small enough to pack anywhere.

Brakes

Back to Top

$199.95

320mm Supermoto Brake Rotor Kit from EBC

DRZ400E/S

Full braking power for your DRZ400 supermoto conversion. Floating EBC 320mm brake rotor with gold anodized alloy carrier. Includes caliper relocation bracket.


$24.95

Billet Rear Brake Clevis

DRZ400E/S/SM

Bling for your bike. This sweet blue anodized billet piece replaces the stamped steel clevis that connects your brake pedal to the master cylinder.

 

$7.95

Bel-Ray DOT 4 Brake Fluid


Bel-Ray's Super DOT 4 brake fluid is specially formulated to exceed all DOT 3 & DOT 4 specifications. What this means to you is exceptional resistance to vapor lock and maintaining consistent lever feel during hard brake use. This 12 fl. oz. bottle is enough to finish just about any job.

  • Formulated for hydraulic brake systems
  • Mixes with all fluids meeting DOT 3 and DOT 4 specifications
  • Boiling point: dry 446°F, wet 311°F
  • For brake systems and hydraulic clutches, except systems using mineral base fluids

Front




Rear



Master Cylinder Repair Kits


All the parts you need to freshen up your front brake master cylinder. New piston, seals, return spring, boot and snap ring.


$29.95

Rear Brake Caliper Guard

DRZ400S

Quality aluminum caliper guards from Works Connection protects your brake caliper and looks great.


$49.95 to $64.95

EBC Brake Pad Sets

DRZ400E/S/SM
  • Sintered Pads are best for regular riding -long life, and good performance in all conditions
  • Sport Carbon pads are made for fast riding in dry conditions - not recommended for mud, water, or sand
  • Race Sintered are designed for racing use
  • Includes front and rear brake pads

$24.95

Mini Bleeder




  • Combines wrench and bleeder valve into one convenient and compact tool
  • Fits most 8 mm bleeder nipples
  • Bleeds brake systems and hydraulic clutch systems
  • Internal check valve for fast easy bleeding
  • Anodized billet aluminum handle with chrome moly steel body
  • Compact size for tight spaces
  • High quality internal seal
  • Multi position handle

Front




Rear




Steel Braided Brake Lines


Steel braided lines have a Teflon tube as a core wrapped with a stainless steel wire braided exterior which doesn't allow the brake lines to stretch under pressure like stock rubber lines do.

The benefit is a firmer brake lever with better feel because the energy that was going into stretching the stock lines now goes straight to the brakes.

Select




Disk Guards

DRZ400 S/E

Protect your brake discs with high-grade aluminum alloy disk guards by Devol

.
  • Covers entire front leading edge
  • Light weight and very effective
  • Easy to install; all hardware included

Select




Brake Caliper Rebuild Kit

DRZ400S

Each kit includes all necessary rubber components and brake pins.

Controls

Back to Top

$41.95

Handlebars


These handlebars are high quality at an affordable price. Several bikes here in the shop use these bars and we like them.

  • 7/8" mounting area, fits stock mounts
  • Manufactured from 6061 T-6 aircraft aluminum
  • Knurled center section and clutch end
  • Bar pad included
  • Reduces rider fatigue by absorbing impact, shock and vibration

  • Different bend dimensions (see diagram for help)
  • CR High - W = 802, H = 99, R = 65, S = 54, B = 13 degree
  • KX/RM - W = 805, H = 93, R = 50, S = 55, B = 14 degree
  • YZ/WR - W = 803, H = 92, R = 56, S = 57, B = 15 degree

$59.95

Powermadd 2" Handlebar Riser


  • 4.75" wide, requires 7/8" bar clamps on bike
  • Raises handlebars 2 inches and allows fore/aft position adjustment
  • Provides dual pivot points for optimum bar positioning
  • One piece design is made from solid aluminum for superior strength
  • Available for 7/8" or 1 1/8" bars



OEM Replacement Levers

DRZ400E/S/SM

OEM replacement levers for your DRZ400S/SM/E


$27.95

DRZ400E Competition Lever Set

Dirt models only 00-03

Competition levers by Moose Racing incorporate a cast aluminum lever with silicone grip inserts and anti-friction bronze bushings

  • Levers are approximately 1" shorter than stock
  • Sold as a set

$54.95

Quick Throttle Tube

DRZ400 all
Quick throttle DR650 DRZ400

Opens your throttle 15% faster. No more 'double handfuls' to get it wide open. Removable end cap for bikes with hand guards.


$10.95

ProGrip 714 Rally Grips

Our Favorite Grips!

Replacing your handlebars? Time to replace those worn out grips? These grips feature a thicker design that dampens vibration. The soft shoulder allows ease of movement. Three wire-tie grooves are molded into the grip to make securing them a breeze.

Select Controller

BikeMaster Heated Grips


Highly efficient design delivers warmth faster than traditional heated grips.

Choose from the standard five level push button temperature controller, or the LCD display controller which shows the selected heat level and available battery voltage.


$89.95

Vista Cruise Throttle Lock Kit

DRZ400 all

Ease the pressure on your wrist during those long highway drones out to where the fun begins. ProCycle has developed this kit that includes a Vista-Cruise throttle lock, a specially modified alloy throttle tube and an anchor plate that attaches to your throttle housing. Just flip the thumb lever down to apply enough friction to hold the throttle in place. Use the supplied longer screw to attach the anchor plate to your lower throttle housing bolt hole. Also included is a tension adjustment tool that you can keep on your key ring. Keep the applied tension lightly adjusted so it's easy to roll the throttle off.



$10.95

Crampbuster Cruise Assist

(Made in USA)

This little jewel reduces hand fatigue and cramping on long rides or daily commutes. The Crampbuster is not a throttle locking unit but rather a simple clip-on device which allows you to relax your grip while riding.

Choose Size:


Doubletake Mirrors


Enduro Mirror

ADV Mirror

Made from a nylon and fiberglass composite, these mirrors are extremely durable. They easily fold out of the way when you head off-road.

Enduro Mirror 4" diameter

Ideal for dualsport use, where you want the absolute minimum profile when folded down. SAE spec convex glass gives a much greater field of view than flat glass.

ADV Mirror 3" x 5"

Adventure mirrors are designed for adventure riding where you want your mirror extended most of the time.

Mirrors mount to any 10mm perch. Mirror and arm included as shown in pictures. If you need a mount for your mirror, click here to see our split clamp mirror mount and mirror mount adapter.


$22.95

Folding Dualsport Mirror


This new mirror screws into your stock mirror mount but can be folded out of the way when it's time to hit the trails. These are quite similar to the very popular KTM folding mirrors but at half the price of the KTM part. Fits either left or right side.


$49.95

Bar-End Mirrors

Sold in pairs

Bar end mounted mirrors move the mirrors out past your elbows so you can actually see what is behind you. They can mount with or without hand guards.

Select Cables



Throttle cable

Replacement Cables

DRZ400 all

A quality replacement cables from Motion Pro


$9.95

Cable Luber


Keep your cables lubed up and working freely. This tool is used to inject lubricant into cable housing. Clamps over housing and wire allowing an aerosol can to be connected. Once lube runs out the far end, the cable is lubricated.


$20.95

Dri Slide Cable Lubricant


Goes on wet but evaporates to leave a dry moly film. This unique dry film won't attract dirt or dust, is highly resistant to water, and prevents rust and corrosion. It is the perfect lubricant to use on brake and clutch cables. Includes applicator needle to get into cables, locks and anything else that needs dry lubrication.



$139.95

New! 081414

Acerbis X-Factor Handguards


New from Acerbis, these handguards come with mounts that will work on both standard and and oversize bars. The aluminum wrap-around bar is the biggest on the market with two large plastic shields that are also some of the largest we have ever seen. Don't let the pictures fool you, these are larger and wrap around your hand better than the Cycra guards below.

These are available in black, white, red, blue, yellow and green.

Select Bar Size & Color:

$109.95

Cycra ProBend Handguards


Here are our favorite handguards for the Fly Aero handlebars listed at the top of this section. These oversize bar mounts also fit Renthal, Neken and ProTaper Bars. The construction of these handguards feature heavy duty aluminum guards with colored plastic deflector shields. They offer great protection from those trees that jump out at you on the trail and the cold wind and rain you encounter on the street. They feature a deep bend on the outer bar end for maximum freedom of hand placement and high quality bar mounts on the inside. True dual-sport protection for your DRZ400.


$39.95

Billet Throttle Tube

DRZ400 all
billet throttle tube DR650 DRZ400 DR350

Suzuki makes it almost impossible to replace your stock grips. It's much easier with a new throttle tube. Removable end cap for bikes with hand guards.


$21.95

Moose Molded Foam Handguards



Riding in the harsh conditions of winter? Good, we are too. These foam hand guards are great. You get the extra protection in bad weather to help keep your hands warm and dry. These just about double the protection from most plastic type deflectors.

The outer shell is made from heavy-duty 500-denier nylon with 1/2" closed cell foam to keep the wind, cold and rain at bay.


$32.95

Mirror Extenders


Can't see past your shoulders? These 2.5 inch long mirror extenders will get your mirrors higher and farther out for a much better view of the road behind you.

  • 10mm Threads
  • Sold in pairs
Select Color:

$219.95

New! 011315

Warp 9 Adventure Pegs

DRZ400 all (Made in USA)


New from Warp 9, top of the line Adventure Pegs. a full 5" long and 2.5" wide will give your feet the perfect perch whether you are cruising down the highway or standing up hammering down a singletrack trail.

  • Ceracote coated Chromoly steel pivot for the ultimate in strength
  • Replaceable 7075 T6 Aluminum Platform
  • Permanent Stainless Teeth provide the ultimate in non-slip traction
  • Built-in bottle opener in the bottom!

$165.95

Pivot Pegz Mk3

DRZ400 all

Pivot Pegz have set a new standard in footpeg performance and quality and now they are even better. The new Mark 3 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 3 also incorporates new heavy duty, long life springs and they come with a lifetime warranty.
Pivot Pegz aim is to build the best footpegs in the world and they really do perform as good as they look. There's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever.

  • Mega wide 60mm platform
  • Widest and lightest pivoting pegs on the market
  • Open design = less mud packing
  • Unique multi-directional grip pattern
  • Outstanding build quality
  • Race proven design and durability


$144.95

CJ Designs Mk 3 Pivot Peg Extensions

All MK3 Pivot Pegz

This is one of the more essential items that should be added to nearly every bike before you ride it. Give yourself the pleasure of riding with a secure platform for your feet that gives you a positive grip and extends the foot bed so that you aren't riding with just half your foot on the peg. If you stand up at all this will revolutionize your confidence level and make for a far less fatiguing ride.

Product Features

  • CNC machined billet aluminum
  • Stainless steel traction pegs
  • Anodized orange or black and machine finish (bare alum.)
  • 1-5/8" longer and 1/2" wider than
  • Requires drilling 3 holes in your Pivot Pegz for mounting (easiest if done in a drill press)

$29.95

Warp 9 Shift Lever

DRZ400 '04-Current

The arm is cast and then black anodized while the black anodized knurled aluminum tip is folding and returns via a stainless-steel return spring. Includes the pinch bolt as well.

The tip is replaceable in the event of damage or if you just want to spiff up you bike with a different color. The tips are available in Black, Blue, Orange, Red and Yellow. See below to order a new tip.

Photo represents color combination, not specific year, make, model, or bike.





$11.95

Warp 9 Shift Lever Tip

Sold Separately

These colored tips are for the Warp 9 Shift Levers only! If you have damaged yours in same fashion, or just want a touch of color, this is the hot ticket. These are held to the cast Warp 9 lever with a pin and e-clip making them easy to change out. Includes new pin and e-clip in case you lose yours!

You can also order just a new pin hardware kit which comes with new pin, clip, pinch bolt, spring, and spacer.


$27.95

Folding Shift Lever

DRZ400 all

Replacement shift lever with folding tip.


$39.95

Steering Head Bearing Kit

DRZ400 All
  • A set of high quality replacement steering stem bearings
  • Tapered roller bearings provide decreased maintenance along with less wear, smoother operation and longer life
  • Kit comes complete with both upper and lower taper bearing cups, cones, and most include top and bottom seals

Luggage Racks

Back to Top
Choose Items:

$39.95

New! 062316

RotoPax Mounting Plates

For use with ProCycle racks only (Made in USA)

ProCycle now has seperate Right and Left plates that bolt to our side rack for mounting your RotoPax fuel or water containers, or any other such device.

$59.95

New! 062416

Top Rack-Givi Mounting Plate

For use with ProCycle racks only (Made in USA)

Attach this plate to your ProCycle Cargo Rack and then pop your Givi Monokey Top Case right on. Makes for easy commuting and errands. Can pop the case off in seconds or put your helmet inside and lock it up.

All hardware included.

$119.95

New! 062416

Givi Bags Side Mounting Plates

For use with ProCycle racks only (Made in USA)

ProCycle now has a plate that bolts to our racks for mounting your Monokey Givi hard cases. Pop these onto your rack and your Givi Monokey bags will slide right on and then lock in place just like on any other racks. Now you can swap your Givi bags between bikes and don't need to buy another set. Genuine Givi latches and all the hardware you need to mount them up to your ProCycle Racks included. This is for set of plates both right and left.

Select Bike


Pro Moto Billet Rack

(Made in USA)

Not only are Pro Moto Billet Cargo Racks brutishly strong and functional, but they look great too. Each cargo rack is methodically engineered, then CNC machined on-site from a 1/2 inch thick plate of USA made 6061 aluminum by master machinists.

The cargo racks are then hard clear anodized for durability. PMB uses only stainless steel fasteners for worry-free years of riding. Excellent instructions and all necessary hardware is included.

Need to mount your turn signals to your new Pro Moto Billet Rack? Just add a set of CNC machined aluminum Turn Signal Brackets for $15.95 and that will be no problem. See bottom image.



Nomadic Racks Rear Rack

 (Made in USA)

DRZ400S/SM rack is available in both a Utility and Sport version. The Sport version is 9" x 9" and the Utility is a full 2" longer for added storage space. Both of the S/SM racks have tabs so you can bolt the stock tool bag on.

Please select the rack for your specific model as the differences are significant

  • Fully welded construction from 16 gauge mild steel
  • Powder-coated black textured finish
  • Rigid 4 point mounting system (except DRZ400E model rack)
  • Hardware and detailed instructions included

$14.95

Nomadic Racks RotoPax eXpander

 DRZ400 (Made in USA)

This kit fits all Nomadic tubular type racks. (All flat stock racks are already RotoPax compatible)

The upper image shows the kit, which includes all the hardware and instructions required. The lower image is just an example of what the eXpander looks like mounted to one of their racks.

Select Package



New! 062316

ProCycle Rack System

DRZ400S/ES/SM (Made in USA)

ProCycle rack system by Moto-Mule is designed and manufactured by dual sport riders that know what it takes to create a durable and versatile luggage rack.

Our racks allow for easy installation of both soft and hard luggage.

Go to our Luggage Page and pick out any set of qualifying side bags or cases and get $20.00 off side racks!


Construction

  • 5/8" steel tubing
  • Computer precision bending
  • Durable powder coat finish
  • CNC cut brackets
  • Top rack dimensions 15" wide 11" long
  • Top rack has RotoPax and hard case mounting tabs
  • All mounting hardware included
  • Additional hard case and RotoPax mounting kits are available in this section

             Click on the image below to start the moto-mule ProCycle Luggage System video.

$179.95

New! 062316

Quick-Release Luggage Mount

For use with ProCycle racks only (Made in USA)

Hard bags can be a pain in the you-know-what to get off and on. Not now. This set-up allows you to remove any hardbags you have by pulling a simple T-handle. Did we mentioned that they are lockable as well? Push down on the key lock and your bags can't walk away while you stop for lunch.

This kit includes plates and hardware to mount right and left hand bags to your moto-mule ProCycle Racks. Check out the video below to see how nifty this set-up is.


$299.95

Moose Expedition Side Racks

DRZ400S/ES/SM (Made in USA)

From Moose Racing, Side Racks for the DRZ400. These are a great companion to the Moose Expedition Side Cases or the Wolfman Expedition Saddlebags.

These racks are made from precision-shaped 3/4" (18mm) diameter steel tube with motorcycle-specific mounting arms and brackets to assure a proper fit. Machined caps, tabs and spacers add to the mounts dimensional precision. Finished products are then powder coated black with a matte finish.

All hardware is zinc-plated with flange-style heads and nuts are also flange style with nylon or metal locking threads.

Select Package



Happy Trails SL Side Racks

(Made in USA) DRZ400 S/SM

The Happy Trails SL racks are made with 5/8" steel tubing and utilize a 3 point mounting system.

Save a bundle by ordering your SL side racks and saddlebags together in one package. This bag/rack combination is an easy answer to the need for waterproof soft luggage and a way to secure it to the bike. We combine the Happy Trails SL side racks with Wolfman Expedition Saddlebags and

Select Size/Color:

ROK Straps

The ultimate stretch strap

These flat tie down 'stretch' straps are designed specifically for motorcycles, ATVs and snowmobiles. Carry anything on your motorcycle securely and without scratches with these flat - no hooks - tie down straps.

ROK Straps are a must have for any dual sport or adventure rider!



ROK Straps are a two-piece strap that has a quick-release buckle in the middle and loops on each end.
One end of the strap is a heavy duty nylon, the other has a strong stretchable section. Instead of hooks
that can slip or come undone, ROK Straps have a loop sewn in each end. you pass the buckle around
your frame, rack or other secure point and then back through the loop in the end making for a very secure
mount. With each end secured, connect the buckle in the middle and simply tug the slack end of the strap
until your load is firmly held in place.

Luggage

Back to Top

Saddlebags & Hard Cases


Choose from a huge selection of sidebags and hard cases from top brands.

  • Wolfman Luggage
  • Nelson Rigg
  • Giant Loop
  • Moose Racing

Tank Bags


Tank bags provide easy access to personal items and come in a variety sizes, styles, and colors.

  • Wolfman Luggage
  • Nelson Rigg
  • Giant Loop

Duffel Bags


Select from an assortment of sizes, designs, and brands.

  • Wolfman Dry Bags and Rolie's
  • Saddlemen Destination Pack
  • Givi waterproof bags
  • Firstgear Torrent bags

Top Cases


Top cases by Moose Racing allow easy access and transportation of items for long rides or daily commuting.

  • Expedition Aluminum Top Cases are a perfect match for the Expedition Side Cases. Available in 25 or 38 liter sizes
  • Expedition Hard Top Cases are perfect for daily commuting and errands around town. Available in 28 or 47 liter sizes

Fender Bags


Fender bags are perfect for carrying tools and tubes on any adventure.

  • Wolfman 1.25 Liter front fender bag
  • Moose Racing removable rear bag
  • Wolfman 3.5 Liter tool bag
  • Chase Harper rear fender pack

Accessories


Luggage accessories to complete your luggage set.

  • RotoPax fuel and water containers
  • ROK Straps
  • Universal Mounting Kits
  • Much more!

Helmets & Apparel

Back to Top

Dual Sport Helmets


We have put together a great list of dual sport helmets for any budget.

  • Arai XD-4 Dual Sport features great quality and looks
  • Shoei Hornet X2 for serious dual sport enthusiasts
  • Bell MX-9 Adventure new for 2015 is everything you want at a great price
  • AFX 41-DS Dual Sport features an inner flip down sun shield
  • Fly Trekker gives great quality and price

Rain Gear


Stay dry with quality rain gear by Frogg Toggs. Frogg toggs is committed to providing the best in affordable, innovative rainwear technology. ToadSkinz technology is a newly developed hybrid fabric that was engineered by the frogg toggs research team. This unique new material has the look and feel of a traditional polyester rain suit but with a non-woven inner layer that provides guaranteed waterproof and windproof performance in a lightweight garment with great breathability.

Gloves


Choose from a great selection of Firstgear dual sport gloves.

  • Ultra Mesh Gloves
  • Kilimanjaro Gloves
  • Kathmandu Gloves
  • Cold Weather Gloves
  • Many More!

Accessories


We have put some common sense dual sport items on our accessories section and will be adding stuff as we find it.

  • Hydration packs by Thor and Moose Racing
  • Backpacks from American Kargo and Moose Racing
  • Neck warmers and High-Vis vests

Dual Sport Apparel


Choose from top of the line jackets, pants and our every own ProCycle T-shirts

  • Kathmandu jacket and pants
  • Urge overkill Jacket
  • Adventure Mesh jacket
  • Firstgear Thermosuit
  • Kilimanjaro jacket
  • And more!

Heated Gear


Stay warm on those long winter rides with top of the line heated gear.

  • First Gear heated clothing features Nickel Alloy heating technology
  • Venture heated gear comes standard with harness and controller
  • Heat Pump Vest and battery powered gloves also available
  • Check out our Seat warmer and Heated grips

Footwear


Our favorite dual sport boots have been tested and approved by the ProCycle staff.

  • New! 100115 Forma Adventure Boots
  • Icon Raiden DKR Boots
  • Alpinestars Scout Boots
  • Gaerne Balance Oiled boots

Accessories & Tools

Back to Top
New! 052316

Maps and Navigation




Check out our new Maps and Navigation page!

  • Butler Maps
  • Benchmark Maps
  • Delorme Maps
  • GPS Units
New! 052316

ProCycle NAVIGATOR


Navigation doesn't get any simpler than this. Here is the ProCycle 'binary' Navigator. Don't know which way to turn? Flip the NAVIGATOR and follow your nose. It is guaranteed to lead you somewhere. Probably some place you have never been.

$14.95

New! 030816

JIS Screwdriver Kit


The Phillips type screws used in Japanese motorcycles are actually Japanese Industrial Standard (JIS) screws are very easy to strip if you are using a regular Phillips screwdriver.

Here is a little kit that will make removing and replacing JIS screws much easier. A small portable handle with its own collection of 4 various bits, along with 2 each JIS No. 1, No. 2 and No. 3 bits. These will work in any other bit holders you may have and have a slight magnetic end to hold a screw while you start it.

$10.95

New! 103015

Super Siphon


The Super Siphon makes it easy to transfer fuel from one bike to another; simply shake the hose to prime it and get fuel moving. With 5.5 feet of hose it is no problem to reach whatever needs a bit of your gas. The hose is resistant to gasoline and any other hazardous chemicals. Roll it up and stuff it in your bag and you will be very happy when you need it one day.



$649.95 - $799.95

Garmin 390LM, 660LM and 665LM





Designed by riders for riders, the new Curvy Road routing leads you to the roads most fun on a motorcycle. This programming is standard on the Zumo 390LM. This unit is also equipped with a Tire Pressure Monitor System (valve caps purchased separately). It is bluetooth enabled so you can chat with your helmet on or just listen to the directions from your 390 so you can keep your eyes on the road where they should be.

Simply connect your Zumo with your cell phone and/or a bluetooth-enabled headset. Your Zumo unit will transmit voice prompts to your headset allowing you to hear the street names and navigation commands.

Each of these Zumo systems is designed with an on-board MP3 player so you can enjoy your music, podcasts, etc. Each Zumo also has a picture viewer so you can bring favorite photos along for the ride.

In addition to all these great features, each Zumo has a built-in trip computer with compass display. There's also a speed limit indicator so you know when to throttle down and avoid a ticket.

Another very handy tool is BaseCamp. This web based tool lets you create routes along specific roads and search for and save points of interest, restaurants and fuel stops. Upload your pre-planned trip to Zumo and follow along for a stress free ride. With BaseCamp you can combine track logs, waypoints, geotagged photos, YouTube videos and more into an adventure that you share online. Garmin Adventures is a free, interactive way to record and share your rides.

The Zumo 665LM has SiriusXM Satellite Radio, NavWeather and NavTraffic. Separate subscriptions required for these services.

Protected against water immersion for 30 minutes at a depth of 1 meter.

Click here to read the entire lifetime maps terms and conditions on the Garmin website.


$30.95

Service Manual

DRZ400 all

Clymer repair manuals provides step-by-step procedures based upon the complete disassembly of the motorcycle. This hands-on experience combined with extensive research results in a manual that is both user-friendly and detailed. Hundreds of original photos and illustrations guide the reader through every job.

Whether you’re interested in routine maintenance tasks, troubleshooting, or more extensive repairs, the in-depth coverage provides indispensable information about your DRZ400.


$24.95

Helmet Lok



Small and compact enough to fit in your pocket, jacket or on our belt loop, HelmetLok is designed to lock your helmet to any bike using the handlebar or frame as an anchor point.

Don’t be weighed down carrying your helmet around anymore. Just use the simple to operate, carabineer-style HelmetLok and you can secure your helmet using the convenient outward opening mechanism. The combination can be reset to the number of your choice. Enjoy the security and freedom of HelmetLok.


$8.95

Rim Protectors

Sold in pairs

Protect your wheels from scratches and dings caused by tire changing tools

Includes retrieval cord for easy use


$29.95

Tire Bead Breaker


Changing tubes or tires without the right tools can be a real chore. Don't fight your snug beads any longer, use this 27" long tool that opens to 7-3/4" to provide the leverage you need to easily break your tire bead. Constructed from heavy-duty steel with comfortable no-slip grips, this tool makes the job a snap.


$17.95

Warp 9 Valve Stem Puller Tool



This ultra-cool little tool is used to pull the valve stem through the hole on motorcycle rims saving your finger tips when changing tires, fixing flats or any time the tube has to come out of the rim. It threads inside the valve stem making it easier to pull through the rim hole. You can use it as a valve stem puller, valve core removal tool or a tire deflator.

Handle is CNC machined and has a threaded hole in each end, one to hold and protect the threaded end of the tool and one for a spare valve core (not included). Anodized blue for good looks and corrosion resistance.


$25.95

Clutch Holding Tool


Made from medium carbon steel with hardened jaws. It features spanner pins and the jaws open up to 5" wide. It's ideal for holding clutch hubs, flywheels, gears, sprockets, etc. From Motion Pro


$5.95

Motul M4 Hands Clean


A handy addition to the tool box or in your traveling pack. This is amazing stuff! Rub a little bit of the paste onto your dirty hands and it lifts the dirt right off. A little more rubbing turns it into dry flakes that brush away. M4 Hands Clean is not messy or greasy.

$49.95

New! 032316

Tie-Down Handlebar Clamps



These clever tie-down clamps give you an instant anchor point for tie-down straps using your hand grips.

  • Oval opening for single or double tie-down hooks
  • Clamps securely to any 7/8" handle bar grips
  • Machined from forged aluminum
  • Sold in pairs

$19.95

New! 060115

Deluxe Folding Saw


A must have when blazing new or old trails!

  • Soft rubber handle
  • Thumb latch release for safety
  • 8" blade, 9" folded length
  • Steel frame

$6.95

Cycle Wipes


Cycle Wipes are pre-moistened and pre-folded towelettes made with a special non-woven "Dirt-Grabbing Mesh Fabric," which is a fancy way to say that they are soft, gentle, durable, and a lot safer than that old rag or paper towel.

Their formula contains no harmful ammonia and is specifically formulated for helmet face shields.


$139.95

Vapor Speedometer / Tachometer

DRZ400E/S all

Features:
  • Current Speed
  • Maximum Speed
  • Selectable MPH/KPH Display
  • Real-Time RPM Bar Graph
  • Numeric RPM Readout
  • Dual Programmable Shift Lights
  • Up to 20,000 RPM
  • Ambient Temperature
  • Engine Temperature (sensor included)
  • Dual Programmable Temp Lights
  • Clock, Hour Meter, Stop Watch, Ride Time, Accumulated Ride Time
  • Adjustable Distance, Permanent Odometer, Selectable Mile/Kilometer Display
  • Includes Power Connection, Accepts Any Power Input - AC/DC, Auto Switch to Internal Power if External is Removed, Permanent Memory Guarantees Data is Never Lost

Click here to read a 'Ride Review' on the Vapor


$54.95

Trail Tech Vapor Indicator Dashboard


  • Optional plastic dashboard with indicator lights protects the computer and places it in an optimum viewing position
  • Included mounting bracket installs easily to triple clamp of most motorcycles
  • Includes an assortment of indicator light lenses allowing customization to fit your needs

Click here to read a 'Ride Review' on the Vapor & Indicator Dashboard by Jeff.


$99.95

Rigid Halo LED Flashlight


This is not just a flashlight, but a tool - seriously. With 800 lumens using just 10W, it can go for almost 3 hours using a single rechargeable AA battery. 1000' of visibility means that this could be used as a signaling device in an emergency and in fact has a setting that emits SOS strobe in Morse Code. There are 5 different settings:

  • High mode – 800 lumens
  • Medium mode – 500 lumens
  • Low mode – 200 lumens
  • Strobe light
  • SOS Strobe in Morse Code

Package includes black anodized flashlight, AA rechargeable battery and charger. With a beam like this, a SOS strode, you can't live without this. Good for rides, camping, just about anywhere.


$33.95

Mini Air Compressor


Portable 12v compressor is perfect for any tool kit. This unit weighs in at only 14oz and measures just 4"x2"x6".

Features a built in LED light and 0-120 psi gauge

• Comes with everything shown

$51.95

Snapjack Portable Jack


The Snapjack is an easy to use, portable, sturdy jack for chain lubricating, adjustment and chain drive maintenance. Also simplifies cleaning. It can lift the rear tire up to 1/2" to allow the tire to spin freely. Includes front brake locking strap and handy carrying bag.


$28.99

Trimax Rotor⁄Disk Lock


This lock is a must have for any rider. Features a 10mm hardened steel pin that will resist any attack.

Comes with carry pouch and a disc lock reminder cable. Includes three keys, one with a mini flashlight.


$19.95

Waterproof First Aid Kit


 

Kwik Tek waterproof first aid kit is the perfect size for your "Don't leave home without it" list.


$17.95

Tirepro Digital Tire Gauge


  • Large display, readings are shown to 0.1 psi
  • Kpa and Kg-cm2 scales also provided
  • Reads up to 99 psi
  • Ergonomic shape fits nicely in your hand

$59.95

"Tread Doctor" Knobby Cutting Tool


Refresh your front or rear tire instead of throwing them out! Tread Doctor Lightweight heated tool lets you quickly cut new edges into your dull worn out knobby tires.


$35.95

Mini-Morph Pump


The Mini-Morph is actually a bicycle pump, but is probably the best compact pump we have found for adventure / dual-sport riding. It has a fold-out foot and handle as well as a 4 inch hose so you can set it on the ground to pump. At only 10" long, it is small enough to pack anywhere.

Didn't find what you are looking for?
We have millions of parts and accessories not listed on our site available from our vendors.