Search Products

This anodized billet piece, brings a touch of color to your bike. Available in red or blue, it replaces the stamped steel clevis that connects your brake pedal to the master cylinder.

This kit includes LED headlight assembly with plug-and-play wiring harness, a specially designed adjustable steel mounting bracket, and all the required installation hardware.

The headlight features two primary sets of LED projectors, a wide low-beam pattern with distinct upper cutoff and a center spotlight high-beam for long range visibility.

The low-beam consumes 20W and remains powered when the 15W high-beam is fired. There is also a daytime running light feature which can be powered for additional glow. The LEDs are rated for 50,000 hours and operate at a 6000K color temperature.

No cutting, no drilling, no wiring modifications! Installation takes 5 minutes.

Two colors to choose from, Chrome or Black. Light output and beam pattern is the same for either color.

Non-DOT

This plug-n-play kit includes sealed LED headlight assembly and adjustable mounting brackets specifically designed for the 1996-2020 DR650SE. No wiring, soldering, resistors, drilling, or fabrication required however due to the size of the headlight minor trimming on the backside of factory plastic headlight fairing is needed in non-visible areas.

• Low Beam: 25W, 3,600 Lumens
• High Beam: 40W, 4,500 Lumens
• Color Temperature: 6,500k
• CREE LED Chips
• DOT & SAE Approved
• CE, RoHS, ISO9002, IP67

Modern LED technology with a classic look!

This plug & play kit is built around the all new Holley RetroBright LED headlight which comes in three different colors.  

Choose from Classic White (3,000K), Modern White (5,700K), and Euro Yellow.  The RetroBright also features a replaceable bulb.
 

Low Beam: 25W, 2,000 Lumens
High Beam: 30W, 3,000 Lumens
Color Temperature: 3,000k or 5,700k
DOT Compliant
Beam Pattern: Left Hand Drive (USA)

This device will pulse your brake light automatically. There are over 1000 possible pattern combinations with individually programmable Flash Speeds, Pre-Delay, and Flash Durations, as well as a disable feature to disable the unit. This device gives the end user the widest range of possibilities for customizing your tail light safety flash. With simple programming setup using only your brake lever, their is no disassembly or removing of the seat required to change the programming on the device.

Features:

• Independently programmable flash speed, flash duration, and pre-delay
• Works for LED or Standard Bulb Tail Lights
• All Solid State design
• Meets or exceeds OEM load rating specifications
• Over 1000 possible flash pattern combinations
• Simple programming setup with your brake lever
• Extremely compact unit size; 20mm x 20mm x 12mm

There is a lot of technology packed into this tail light/fender eliminator kit. You have programmable turn signals and Safety Brake Pulsing both built into this product.

You can enable or disable the safety brake pulsing feature.
This kit includes only the highest quality components, including the pre-installed 12oClockLabs processor board, which is made in the USA.

• Plug and Play
• 7 Different Programmable Turn Signal Patterns 
• Safety Brake pulsing built in (Can Enable or Disable)
• Superbright LED's; For excellent brightness, even in direct sunlight
• License Plate Light built in
• License Plate Bracket fits the common USA license plates, sloted for maximum plate compatibility.
• Includes Mounting Hardware
• Saves about 2 lbs over the factory tail light setup
• Made In the USA

We recommend a "Fixed Rate Flasher" unit for use with this kit. When you install aftermarket signals it changes the load on a factory signal system.

This kit does not include parts to mount aftermarket turn signals. The pre-installed processor board allows the turn signals to be integrated in to the tail light.

Remove the bulky stock number plate holder with our slim design- comes with LED number plate light.

• Quick and easy install
• Mounting hardware supplied
• Comes with clear LED tail, brake & number plate light
• No mods required for installation
• Available in polished or black PPA coating.
• Pre drilled to suit Australian licence plate

*Please Note:  Brake light does not come with necessary/factory connectors. Some cutting, crimping, soldering of wires may be required for connection.

This relay will fix your flash rate problem caused by aftermarket signal lights and/or integrated tail light. If your signal lights flash too fast or do not flash, this part is your solution! Plug and play - easy installation.

Only ONE relay is needed per motorcycle.

Features

• Slows signaling flash rate back to the normal rate when your bike goes into hyperflash state (or your signals stay on constantly)
• Plug and play installation: simply replaces the relay already on your bike
• Fits like OEM

This component works with the following signal configurations:

1. All stock
2. Stock taillight, aftermarket signals
3. Integrated taillight, stock signals
4. Integrated taillight, aftermarket signals.

The SignalMinder unit is designed as a plug-in accessory for many Japanese bikes. SignalMinder uses a microprocessor to cancel the turn signals at one of three selectable time outs; 10, 20 or 30 seconds.

You can also make it so that all four of your signal lights also act as running lights and establish a dual-channel system on your bike. With the dual-channel system, when you activate the RIGHT turn signal three times in succession, you get 4-way hazard flash lights.

Connecting the 12 volt supply from the brakes to the SignalMinder, also allows for a brake flash option.

There are many options and configurations using this electronic tool.

No wire cutting required. The kit includes Scotchlok connectors to tap into existing wires.

Your choice of an aluminum bolt-on foot pad or a steel weld-on unit. Each will make the footprint of the stock side stand considerably larger, preventing your DR from tipping over in soft terrain. The bolt-on unit is cut from aluminum and then powder coated black, it comes with stainless steel mounting hardware.

The bolt-on pad and does require use of a drill for installation. The weld-on pad will need to be welded to the stand and then the entire unit painted for corrosion protection.

A must have for lowered bikes.

• Special Feature: Bigger kickstand shoe. 
• Extends approx. Stock length and shortens up to 4" for the DRZ400S
• Extends approx. 1.5" longer than stock and shortens up to 2.5" for the DRZ400SM
• Material: Steel tubing with black powder coated finish for strength and durability

Inexpensive way of getting the factory look. Adds 1/2" of width to any standard foot peg. These will give you a much more stable platform when standing on the pegs.

Sold in pairs.

Pivot Pegz have set a new standard in footpeg performance and quality, and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty.

Pivot Pegz aim to build the best footpegs in the world and they really do perform as good as they look. Here's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever.

• Mega wide 60mm platform
• Widest and lightest pivoting pegs on the market
• Open design = less mud packing
• Unique multi-directional grip pattern
• Outstanding build quality
• Race proven design and durability

See below for extenders for these pegs to make them true ADV pegs!

Front fender from ProCycle Plastics (formerly DSA) is shaped very much like the OEM DRZ400SM front fender. Big enough to be functional without wind-steering the bike like the stock fender does. Vacuum molded, these are a design improvement over stock. These are fully compatible in any combination with the original factory plastic.

A stainless steel front fender brace. Helps stabilize your front fender.

Gives additional strength for carrying a fender mounted tool bag.

Fits on top of the fender and bolts between the fender and bottom triple clamp. Stainless steel won't rust or corrode. Includes hardware.

Requires you to drill one hole in the fender for mounting.

Molded using a very durable, lightweight 1/8" thick polycarbonate - giving the windshield a high impact strength and making it shatter-resistant with a superior light transmission quality. Mounts quickly and easily onto the stock headlight cowling for a clean factory look. Drilling of the cowling is required, hardware is included. Removal for trail riding is also quick and easy.

Only Clear screens are available at this time.

Transform your ride. MadStad's patented mounting system allows riders to adjust the height and angle of their motorcycle windshield resulting in much smoother airflow, better wind protection and a more comfortable ride than any fixed windshield can provide. Better still, this dual-sport version pivots the shield down and forward to get it out of your way for off-road riding!

What's included in the kit:
Their complete bolt-on system is custom-made for your bike and includes everything needed to mount and position the shield. Your bike will not require any modification.

• A set of MadStad adjustable dual-sport brackets
• 3/16" (4.5 mm) thick cast acrylic windshield.

The MadStad brackets bolt to the top of your fork clamps and are completely free of the handlebars. You can adjust the shield for the optimum height, angle and airflow for comfortable street and highway riding. When going off-road you can leave your comfort adjustment as-is and pivot the entire system down and forward in front of the headlight so you can get it out of your face completely. When it comes time to hit the pavement again, simply pivot it back up and you are back in street riding comfort mode.

Transform your ride.  MadStad's patented mounting system allows riders to adjust the height and angle of their motorcycle windshield resulting in much smoother airflow, better wind protection and a more comfortable ride than any fixed windshield can provide.

What's included and what's not included in the kit:
Their complete drop-in system is custom-made for your bike and includes everything needed to mount and position the shield.
Your bike will not require any modification.

• Black hardened acrylic base plate and mounting hardware
• A set of MadStad adjustable brackets
• Rear support brackets
• 3/16" (4.5 mm) thick cast acrylic windshield. 

The MadStad adjustable brackets sit out in front of your fairing on black fly screen which attaches in place of the factory shield. With the windshield now separated from the front of the bike and the fly screen helping to deflect wind up from underneath, you have total control over the shield height, angle and airflow. This lets you dial in a smooth ride and quieter cockpit far better than any fixed windshield can provide.

Quality replacement radiator air scoops. Sold in pairs for gen 1 KLR650.

Available in 4 colors.

A 10-pack of drain plug sealing crush washers. Replace your sealing washer at every oil change to prevent a leak.

Extra protection for your motor! Strong magnet at the end of the plug picks up ferrous metallic flakes in your oil, protecting your engine!

It is a good practice to replace your sealing washer with every oil change. These 10 piece kits are made up of 5 Copper washers and 5 Aluminum washers. The manufacturer recently decided to make half of the kit Copper washers as that is the material of choice for many OEM manufactures. This gives you the opportunity to decide which you prefer, but either will work great at creating a leak-free seal between the case and the drain plug.

Keep your motor running right with a fresh plug.

A Dual Electrode spark plug will last longer than a single electrode plug because the wear is shared between the electrodes.

GoldPlug is the gold standard in engine protection.

Stainless steel drain plug with an extremely strong magnet that picks up metal flakes in your oil.

12mm Thread

Cylinder Works Standard Bore High Compression Cylinder Kit

• Uses Vertex #23550
• Compression Ratio 13.5:1
• Cylinder Diameter 90 mm
• Standard Bore, High Compression
• Displacement 400 cc
• Engine Type 4-Cycle
• Includes Cylinder, Piston Kit, and Top-End Gasket Kit

Kit includes hardened steel bushing, an upgraded seal, an O-ring and lock washer.

Genuine Suzuki OEM o-ring for your crankshaft access engine plug.

Genuine Yamaha replacement gaskets for your side covers.

K&L® shims exceed the maximum of the Apparent Rockwell Hardness "C" scale. Shims average 47.0 compared to the 46.0 maximum.

This kit fits KLR650 87-18 as well as other brands and models , please verify correct size for your model before purchase.

The long awaited Wide Ratio Transmission from Nova Racing. Now you can have your trail gearing without giving up your highway gearing.

Both sets are lower than stock in 1st and 2nd gear and taller than stock on 3rd thru 5th gears. Not only will Nova give you better gear ratios but the high quality components will shift smoother and engage more solidly. The tables below show each gear ratio and the original OEM ratios for comparison.

To help put the ratio changes into perspective switching from the OEM 15T to a 14T sprocket lowers the gearing by 7.1% in all gears. Switching from a 15T to a 16T raises the gearing by 6.6% in all gears.

Stage 1 - Excellent mid-range and top-end power increase.

Uses stock valve springs and rockers.

• Exhaust Cam Lobe Duration at 1mm 258°
• Exhaust Cam Lobe Lift 8.800mm
• Exhaust Cam Valve Lash 0.200mm
• Intake Cam Lobe Lift 8.800mm
• Intake Cam Valve Lash 0.150mm
• Intake Lobe Duration at 1mm 258°

  Does not incorporate compression release.

This CNC cap will replace the stock gas cap on the stock tank. You do need some parts from the stock cap, so don't throw it away yet! It is not difficult and this kit includes the additional hardware required. Also included is a vent tube with a matching cap.

For use on STOCK TANK ONLY! This is NOT a locking cap.
Does not fit California model DR650

A replacement gas cap for your IMS tank. Newly redesigned to resist damage from new fuel additives that were hard on the seal in the old style cap.

Replace your lower chain roller with this high quality roller with 2 sealed ball bearings. The stock roller has no bearings. It's just a plastic wheel riding on a bolt. Ball bearing chain rollers are smoother, quieter and last longer.

Clip style master link for the EK 428 O-Ring chain. Keep one in your tool kit for trail side repairs.

With this upgrade, you can avoid having to keep new replacement cotter pins on hand every time you adjust your chain.

*Black front fender with various superficial scratches on the top of the fender. Sold as is.

Front fender from DSA Concepts Plastics is shaped very much like the OEM DRZ400SM front fender. Big enough to be functional without wind-steering the bike like the stock fender does. Vacuum molded, these are a design improvement over stock. These are fully compatible in any combination with the original factory plastic.

Minor scuffs on top from shipping damage that does not affect function or fitment, only visible up close. Available in black only. Comes with original packaging and all hardware. Sold as is.

This DRZ400 rear rack, hand-built by B&B Engineering in Australia is made from 4mm aluminium 5083 plate tig welded to the support tubing circumventing the plate. This material was chosen because of its extreme suitability for welding as well as abrasion and impact resistance, and all of this keeping in mind the full weight of the bike and rider. Once complete they are given a polished finish or coated with a super-durable black polymer. All Carry/Luggage Racks are supplied with the necessary stainless clamps and bolts where possible.

These racks are smooth and sturdy enough to use as a grab handle.

Check out the bolt-on Luggage Plate for the B&B Rack for those times you need to carry a larger load!

Antigravity Batteries introduce the ground-breaking "RE-START (RS)" line of batteries. These are the first batteries with built-in jump starting! They intelligently monitor their status, and just before going completely dead, puts itself to sleep with just enough energy to get your vehicle started again. Simply press the RE-START button located on the battery, then start your bike and ride away!

These are an extremely lightweight (2.3 lbs.) and high-powered Lithium-Ion replacement battery for motorcycles. These batteries offer the first Battery Management System (BMS) found on a powersport battery and includes low-voltage cut-off, over discharge, over-charge, and thermal protections with real time lithium-ion cell balancing. Highly recommend using a lithium charger to maintain the life of the battery.

3 Year warranty

Product Size is just 5.9"L x 3.5"W x 3.74"H. If you need spacers, select the optional Foam Kit to pad the battery in the battery box.

If you are looking to swap out your stock CDI box, the Big Gun Rev Box is an affordable alternative to highly-priced OEM replacement boxes. It increases the overall RPM limit over the stock box and advances the timing curve and is a direct plug-in replacement.

You must cut the green wire on the 8-prong plug going into CDI box.

A digital voltmeter that can be mounted almost anywhere, on any bike, thanks to ProCycle's multi-position stainless steel bracket. Keeps you informed on the status of your charging system.

Completely waterproof and comes with connectors, wires and thorough instructions. A "must have" device for riders who use heated riding gear, heated grips, additional lighting, GPS, etc.

CNC machined from 2.5mm marine grade aluminum- replace the stock plastic guard

The X-Grip is a frame guard that allows the rider to both protect the frame of the motorcycle from wear as well as adding more grip to the bike.

Made from a dual injected mold; The outer plastic is durable polycarbonate while the inner plastic is durable yet playable and offers incredible grip.

Available in 3 colors

Give your DRZ that factory prepped look and protect your frame.

These frame guards from industry leaders Works Connection are CNC cut and formed from aircraft grade 5052 aluminum. These not only protect your frame from scuff and rub marks from your boots, but also give you a flatter surface for better grip and control with your lower legs. All the necessary mounting hardware is included making these a very simple bolt-on installation.

Yes, plastic! This is a product from our friends at Acerbis. Ultra tough injection molded reinforced composite. Flexible Heavy-Duty Polypropylene will not effect chassis ability to flex, will not effect handling

It's twice as thick as a metal skid plate but is only half the weight. Plastic glides over rocks and roots better than aluminum. It also reflects less engine noise, bike will run quieter and cooler compared to alloy skid plate. Full coverage, mounts to existing threaded holes at the rear of the frame.

Thick carbon fiber plate with many advantages over aluminum.

The use of anti-ballistic composite material provides a longer fatigue life and greater tensile strength than aluminum.

Composite plates are molded to the exact shape desired, making for a closer fit and a more protective plate.

Composite plates absorb vibration and do not amplify sounds like aluminum plates do.

When hit hard, aluminum permanently deforms, bending frame tubes and slicing into water pumps.

Composite plates will bounce back from hard hits and look great long after aluminum plates give up.

Skid plates protect the side engine cases and the water pump in addition to the frame and the center case.

Designed with a high front to keep mud from building up on the engine.

Mounting hardware included.

• Motor Crankcase and Ignition/Clutch covers that protect against wear from boots, impacts, dirt, mud, and other debris
• Right side: provides protection for the clutch cover, water pump, and lower casing
• Left side: provides protection to the ignition cover and clutch actuator
• Molded openings to access the filter cover and oil cap
• Easy to install by utilizing the original crankcase and ignition/clutch cover bolts
• Resistant to high temperatures
• Designed not to interfere with boots

This is the ultimate in radiator guards! It will protect your fragile radiator from nasty front & side impacts.

This ultra tough guard is constructed from 1/8" aluminum and is easy to install.

All Flatland Racing radiator guards have rear mounting brackets for that extra support! All Mounting hardware is included. 

SMX Carbon Look Rotor

• Rotor material has higher friction than plain stainless steel for added stopping power
• Rotors measure 320mm
• Come with caliper relocation bracket
• Designed to fit standard hubs

Made with heat-treated carbon steel for longer wear life and reduced galling.

Galfer USA produces several different brake pad compounds for all types of riding styles and uses. With over 60 years of friction material production and research, they have learned that one compound doesn’t always do the trick across the board. If you are just looking for an OEM brake pad replacement or a high performance race brake pad, they have you covered!

Set includes front and rear brake pads.

Galfer USA produces several different brake pad compounds for all types of riding styles and uses. With over 60 years of friction material production and research, they have learned that one compound doesn’t always do the trick across the board. If you are just looking for an OEM brake pad replacement or a high performance race brake pad, they have you covered!

Set includes front and rear brake pads.

High performance EBC brake pads.

• The "HH" friction rating is the highest in the industry
• Provide maximum brake effect
• Lasts twice as long as organic pads

This is a complete kit that replaces both front and rear brake pads.

• Front pads: Sintered Pads are best for regular riding. Long life, and good performance in all conditions
• Rear shoes: Organic brake pads contain man-made high-performance fibers that are used for their light weight, high strength abrasion resistance and thermal stability.

• Organic brake pads contain man-made high-performance fibers that are used for their light weight, high strength abrasion resistance and thermal stability. These Aramid fibers have a high strength-to-weight, thermal stability and abrasion resistance to provide advantages over steel fiber-based products. They provide excellent stopping power without noise and rotor galling but still provide fingertip control and strong, predictable brake response.
• Double-H sintered metal brake pads feature the HH friction rating, the highest in the industry. These pads provide maximum brake effect and last twice as long as organic pads.
• Semi-sintered pads have an all new recipe containing 30% copper by weight with an organic matrix. This design combines the long life of a sintered pad with the great feel and lack of rotor damage common with full-sintered pads. These can be used to replace Kevlar or sintered metal compound pads.

Premium quality EBC Rear brake shoes.

• EBC brake shoes are radius ground, and edge trimmed
• Lead out chamfers at lining ends

• Sintered Pads are best for regular riding. Long life, and good performance in all conditions
• Sport Carbon pads are made for fast riding in dry conditions. Not recommended for mud, water, or sand.

Includes pads for both front and rear.

Small Wheel models have a 17" Front Wheel and 14" Rear Wheel.

Each kit includes all necessary rubber components and brake pins.

• Each kit contains all necessary components to rebuild a master cylinder
• Made by Nissin, an OEM supplier in Japan

FunnelWeb ProLine Filter Highlights:

• Optimum air flow for increased riding time
• Improved engine protection
• Extended filter change intervals
• Simple to install, clean and re-oil
• Easy fitment

Like all FunnelWeb filters, the ProLine Filter features profile cut, single layer, single density foam that doubles the external surface area of the filter without increasing the original filter size. The ProLine Filter traps dirt, dust, sand and mud over a larger area on its outer surface, ensuring optimal air flow is maintained for maximized engine performance and reliability.

The single layer, single density polyurethane foam has the added advantage of being easy to clean and the ability to maintain its original shape after numerous washes. Overall, compared with conventional foam filters, FunnelWeb offers more protection from dirt ingestion, has longer service intervals and maintains high airflow rates when dirty.

Twin Air Filter's patented design, high quality materials and superior construction deliver unbeatable performance and protection - and make Twin Air Filters the hands-down choice of more World and National Champions than all other filters combined.

The air filter is your engine's only protection against the elements, and your stock filter isn't up to the task. Replace it with a Twin Air-the #1 filter system proven on motocross tracks around the world.

Twin Air's fused layers of open-pore foam and fine inner foam trap even the smallest particles-without restricting airflow.

• Dual-bonded foam design filters out even the smallest dirt particles, while allowing more airflow than two separate layer filters (flow bench proven)
• High quality materials and superior construction deliver unbeatable performance and protection
• Backfire-resistant layer of foam laminated to the inside

Have you lost or broken the stock air filter cage for your KLR? Maybe you need a spare? Here it is, the OEM cage that will fit any of the foam air filters on this page. This kit includes the cage and the mounting hardware.

Kientech Fuel Screw for Suzuki DRZ400S/SM with the Mikuni BSR 36mm carb only. This fuel screw does NOT work on Keihin carbs.

A new slide for the stock Mikuni BST carburetor.

Replace the worn slide guide in your stock Mikuni BST carburetor before it causes additional wear to the needle and needle jet. There are wear indicators on the slide guide that help you recognize when it is time to replace your slide guide. New O-ring included. 

Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.

Low friction 'triple lip' seal design. Oil seals last 3-4 times longer that OEM seals. Kit includes fork seals and dust wipers.

High quality replacement seals for your TW200 forks. Includes both oil seals and dust seals.

Bushings are dyno-tested to 500,000 strokes with less wear than OEM bushings

• Kit includes two slider bushings and two leg bushings
• Kit includes all copper washers and O-rings
• Kit includes two fork seal snap rings

Complete high quality kit to replace the bearings and seals in the swingarm pivot.

Here is everything you need to upgrade your TW200 front suspension. Kit includes: Heavy Duty Fork Springs, Cartridge Emulators, Oil Seals, Dust Seals, and 10w Fork Oil. Just choose the spring rate you want and enjoy your TW even more!

Stock Spring Rate is .50 kg/mm. The .60 kg/mm springs are 20% stiffer than stock while the .70 kg/mm is 40% stiffer than stock.

Installation requires disassembling your forks and drilling out your damper rods.

Introducing the Zeta solid bushings to replace your worn out rubber bushings. We have tested these bushings on our own bike and we love them. No more sloppy handle bars. Plus, they add a little bling factor to your bike! Simply unbolt your bar mounts and swap the rubber bushings with these anodized billet bushings for a more stable handlebar feel.

Features:

• Solid cones for rubber bar mounted stock triple top clamps
• Provides direct control and prevents bar twist when falling down
• Comes in a set of 4 solid cones
• Made of A7009-T6 aluminum

These versatile Risers allow you to clamp a 7/8" diameter handlebar or you can remove the 7/8" reducers and then clamp an 1- 1/8" aluminum "fatbar". If you are thinking of going to a fatbar after you bend your stock set or just want the versatility and option to run any bar, this is the riser to go with. Reducers lock into risers to insure no slippage between components.

These risers use 8mm bolts. Always check and confirm that your bike has adequate cable and brake line length before installing any handlebar risers.

Anti-Vibration Risers may interfere with aftermarket large capacity fuel tanks, and some steering stem clamp configurations (in these cases we recommend using standard pivoting risers).

• Replace OEM throttle sleeves
• Heavier duty and exceed the quality and durability of OEM sleeves
• Will not scar bars like aluminum sleeves
• Nylon fabric composite material
• Molded ridges to help secure grips
• One-piece tube and reel design
• Actual color may vary

High quality replacement cables from Motion Pro.

• Add convenient storage and function to your Adventure bike with these durable rear racks
• Laser cut from 12-gauge, grade 50 steel with durable matte black powder coat finish
• Multiple tie down locations and slots for bag straps or bungees
• Add additional storage capability with optional Adventure Rack Mounting Plates (sold separately)
• All mounting hardware and instructions included
• Rear rack weight limit 25 lb.

Use in conjunction with Moose Racing Adventure Bike Rear Racks.  Plate only, Top Rack sold separate

• Increases overall rack surface area for a variety of basic plastic storage cases or larger soft luggage bags to be securely installed
• Easily attaches to rear rack with predrilled holes and locking tabs in several locations to mount more forward or back on the rear rack surface
• Attaches by locking in the tabs to rear rack and tightens down with a hand knob included in kit
• All mounting hardware and installation instructions included along with a threaded hand knob to install any variety of hard cases with center thread inserts

Fly Racing medium tank bag has an 11 liter capacity that expands to 20 liters.

Touch screen compatible top map/device pocket. Removable base with combined strap and magnet mounting system.

Reflective piping and logos, convenient carry handle, shoulder strap, and rain cover included. Measures: 14"L x 10.5"W x 7"H

Our Tool Tube mounts in place of the little stock tool carrier. The tube is made from 3 1/2" O.D. ABS pipe. It's held by 3 strong powder coated steel straps. Both ends are sealed with waterproof expanding plugs. This is the ideal way to carry those items you always want to have with you on every ride. Tube is approximately 13" long.

You can now order your Tool Tube with a Locking End cap, mini padlock and keys included, on the exposed end.

If you already have a Tool Tube you can order just the Locking End Cap and lock.

Does not fit if your bike is equipped with the new emissions system. The charcoal canister prevents the tool tube from being mounted properly.

No repacking required! The Leo Vince X3 Enduro is made with TIG welded stainless steel internals and aluminum outer shell. It features a semi-direct chamber design that is maintenance free. It's quiet too! Our own in-house testing showed a 84dB sound level using the USFS J1287 testing procedure. 84dB is louder than stock but significantly quieter than any other aftermarket muffler. It includes a certified Spark-Arrestor.

This muffler works on OEM header only!

The RS-2 is a potent and versatile design that evolved from their original TRC, engineered to provide increased power delivery. With a different pyramidal shape that features increased volume, the RS-2 is a quieter system with a larger core — and it offers the added bonus of outstanding performance in a value-priced package.

• Diamond-shaped sleeve
• Large core and increased muffler packing volume means quieter operation
• Stainless steel cone end-cap
• Stainless steel tail-pipe
• USFS Approved spark arrester included
• 6.8 lbs lighter than stock

We recommend Anti-Seize on exhaust fasteners

Constructed from 304 stainless steel and breathes much better than the stock unit. Handmade in the USA with a 1 Year Limited Manufacturers Warranty.

The PowerBomb header promotes better flow by allowing a small expansion of the exhaust gasses. The 'bomb' also acts as a pre-muffler taking the edge off of overall sound levels.

The headpipe gasket seals the joint between the head pipe and Exhaust port. These gaskets are designed to crush a little bit to tightly seal where the pipe fits to the head, thereby making them a single use part. Get a fresh one now avoid having an exhaust leak when you install your new exhaust.

The muffler joint gasket seals the joint between the head pipe and muffler. These gaskets are easily damaged when removing the original muffler. Get a fresh one now to ease installation of your new performance muffler.

Replacement retaining pin for the brake caliper. Includes 1 stock style brake pin.

Be sure to use some anti-seize on the threads when you install it.

Front caliper only for DR350 and DR650

• Fits internal axle hex
• Four metric hex sizes: 17, 19, 22 and 24mm
• 3/8" square drive on both ends
• Heavy duty chromoly steel construction for shop use
• 3/8" square drive on both ends rated to 150 lb/ft
• Use wrench on external hex of tool for situations exceeding 150 lb/ft

• 25ft of .032 stainless wire
• T302/304 Stainless steel
• Great for securing nuts, bolts and grips
• A must have in the shop or tool box

From Warp 9, top of the line Adventure Pegs. a full 5" long and 2.5" wide will give your feet the perfect perch whether you are cruising down the highway or standing up hammering down a single track trail.

• Ceracote coated Chromoly steel pivot for the ultimate in strength
• Replaceable 7075 T6 Aluminum Platform
• Permanent Stainless Teeth provide the ultimate in non-slip traction
• Built-in bottle opener in the bottom!

  NOTE: These pegs DO NOT fit the '18 model!

The Mini-Morph is actually a bicycle pump, but it is the best manual compact pump for adventure / dual-sport riding. It has a fold-out foot and handle and a 4 inch hose so you can set it on the ground to pump!

This thing is small enough to stow away in just about any bag and go unnoticed until you need it to fix a flat or add air after a long arduous ride.

Auxiliary fuel tanks mount to handlebars, forks, or rear racks.

• Suitable for minis, trials bikes, full size bikes, and anywhere else a little extra fuel is needed.
• Each tank includes a siphon kit that connects the tank to the main fuel tank and automatically siphons fuel while the bike is being ridden.
• With this design, the auxiliary tank empties first, before the main tank.
• Does not interfere with headlight, handguards, rear seat, etc.

State-of-the-art replacement seats, Sargent seats are built on a percision-molded lightweight Polytec seat pan. Sargent's proprietary seat foam (Super Cell Atomic Foam) is their own unique blend of resilience, firmness, and vibration-absorption qualities, making it well suited for long distance comfort and support. Sargent seats are covered in a marine-grade, UV-stablized mildew resistant CarbonFX vinyl. Available in standard height and 1" lower than stock. These seats will fit bikes with the stock, IMS, or any other aftermarket fuel tank.

Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a more plush and active ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.

These features combine to offer a custom seat feel, and provide greater enjoyment and increased range on a long commute, or Dual-Sport ride!

Seat Concepts seats are constructed using a foam material that is higher quality than OEM seat foam. Their proprietary formula is plush, while still offering the necessary amount of support. Their unique comfort and shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.

These great features combine to offer you a custom seat feel, and provide greater enjoyment and increased range for long commutes, or Dual-Sport rides!

The Complete Seats come assembled with an high quslity aftermarket pan and ready to ride.

Seat Concepts seats are constructed using a foam material that is higher quality than OEM seat foam. Their proprietary formula is more plush, while still offering the necessary amount of support. Their unique comfort and shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.

These great features combine to offer you a custom seat feel, and provide greater enjoyment and increased range for long commutes, or Dual-Sport ride!

The Complete Seat comes with an high quality aftermarket seat pan with the foam and cover kit assembled, ready to ride!

Features:

• Aluminum air valve cap
• Comes in pairs
• Add some " bling " to your bike
• Helps Keep the air in your tire

For M8 handlebar bolts, the RAM-B-367U motorcycle handlebar base will replace the existing bolt with a 1" B size ball. This rubber ball base provides shock and vibration damping, and is compatible with a wide variety of B size RAM® double socket arms and device holders. The RAM-B-367U motorcycle handlebar base will work with any motorcycle that features an 8mm bolt or smaller on its structure. A smaller bolt can be used, though the load capacity decreases with the bolt size.

• Includes rubber ball, M8 x 55 bolt, M8 x 60 bolt, M8 x 65 bolt (1.25 thread pitch)
• Compatible with any motorcycle M8 threaded bolt; ball base allows for connection to any B size RAM® double socket arm
• Made of marine-grade aluminum for durability and reliability in the most demanding environments
• Backed by a lifetime warranty

Not compatible with handlebars that have a cross bar.

Two parts in one. Not just a cover over the countershaft sprocket, but also a case saver as well! Should you ever throw a chain, this will keep it from going into the engine cases and causing extensive and expensive damage.

High Quality Replacement Wheel Bearings and Seals for your TW200.

Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.

Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.

Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.

Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.

Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.

The rubber coated outside diameter creates an optimum seal at the hub.

Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.