XT225: Controls

Comfortable Oversize (or Fat Bar) Handlebars.

• Black in color. 
• Made from 5mm, proprietary, 2000 series T6 aluminum alloy for superior tensile and yield strength.
• Lighter and stronger than regular bars
• No-crossbrace allows flex to reduce shock and rider fatigue
• Oversize 1-1/8" diameter base reduces to 7/8" to allow standard-size controls/grips
• Etched alignment marks for fast and accurate positioning
• Bar pad included
• Works with stock controls and cables.

For bikes with factory 7/8" handlebars these will require the use of a 7/8 to 1-1/8  adapter (sold separate).

Silver in color

Upgrade your bike with a tapered 1-1/8" bar. Constructed of Aircraft grade 7065 T-6 aluminum that tapers to a standard 7/8" to accept stock controls.

• Lighter and stronger than regular bars
• No-crossbrace allows flex to reduce shock and rider fatigue
• Etched alignment marks for fast and accurate positioning
• Flex Series pad included

These 7/8" bars fit in the stock clamps and raise your grips a couple inches. They look great too!

• Adapt 7/8" bar mounts to accept oversized 1-1/8" handlebars
• An economical alternative to replacing expensive top triple clamps
• Include mounting bolts.

• 4.75" wide,
• Raises handlebars 2 inches and allows fore/aft position adjustment
• Provides dual pivot points for optimal bar positioning
• One piece design is made from solid aluminum for superior strength
• Available for 7/8" - 7/8" or 7/8" - 1 1/8" bars

Requires 7/8" factory bar clamps on bike

These versatile Risers allow you to clamp a 7/8" diameter handlebar or you can remove the 7/8" reducers and then clamp an 1- 1/8" aluminum "fatbar". If you are thinking of going to a fatbar after you bend your stock set or just want the versatility and option to run any bar, this is the riser to go with. Reducers lock into risers to insure no slippage between components.

These risers use 8mm bolts. Always check and confirm that your bike has adequate cable and brake line length before installing any handlebar risers.

Anti-Vibration Risers may interfere with aftermarket large capacity fuel tanks, and some steering stem clamp configurations (in these cases we recommend using standard pivoting risers).

This unique design from Rox allows you to move your bars either closer (1" up and back) or further away (1" forward and 1-1/4" up) depending on rider preference. These risers have an oblong mounting hole so that they will fit virtually any triple clamp with 8mm bolts. A set of reducers lock into the risers ensuring no slippage whether you have a 7/8" or 1-1/8" bars.

Because these are offset there may be limited clearance between the gas tank and the risers when the bars are fully turned on some models, mainly when mounted to move the bars closer.

Protect your thumbs from blisters caused by riding on the inside of your grips.

Sold in Pairs.

Highly efficient design delivers warmth faster than traditional heated grips.

Choose from the standard five level push button temperature controller, or the LCD display controller which shows the selected heat level and available battery voltage.

The Apollo Heated Grips are designed with an integrated adjustable thumb switch, which allows them to easily fit on any kind of motorcycles on the market. The integrated thumb switch gives control to the rider to adjust the temperature level while keeping hands on the bar for a safer ride.

Its wide temperature setting range will keep the rider comfortable under the cold riding conditions.

The 5 color LED display will enhance the visual look of the heated grips and will allow the rider to quickly know at which heat level the grips are set.

This system will also detect if the battery voltage is too low and will automatically shut down the heated grips in order to make sure the rider have enough power to start the engine or use the motorcycle.

Specifications:

• Integrated thumb switch designed for easy installation and control.
• “Plug & Play” wiring connections to shorten the installation time.
• Wide temperature settings for various weather conditions.
• Low Battery Warning protection to ensure the motorcycle has enough power to start.
• 5 color LED Indicators for the rider to quickly know in which heat level the grips are set.

These heated grips from Koso have been tested by us and we can say they will keep your hands warm and give you the grip you need in off road conditions, thanks to the full diamond grip design.

• Clamp-on grips do not need adhesive
• External temperature controller with 5 heat levels
• For use with twist throttle; includes interchangeable throttle cams
• Requires 35W and draws 2.5 amps per pair; low voltage shut off

These new heated devices are for the user that does not want to commit to changing their grips but still wants to maintain the comfort of heated grips. The fitment is intended to fit all sorts of handlebar sizes. They can be installed and removed in a matter of seconds and kept in any sport bag when not in use.

Features:

• Universal fit to be clipped on any handlebar sizes
• Rubber material that is resistant to outdoor conditions and high temperatures
• Thin and flexible silicone wires make them easy to install

• Ergonomically designed
• Medium-density Thermoplastic Rubber (TPR) compound provides excellent feedback and control, without sacrificing durability
• Full diamond pattern for an unparalleled feel in both wet and dry conditions
• Inner diameter optimized to keep grips secure in any conditions
• 115mm overall length; fit 7/8" bars and throttle sleeves

• Feature the classic Vans waffle sole pattern with a subtle domed center section for improved ergonomics and vibration dampening
• 125mm in length
• Fit 7/8" bars
• Sold in pairs

These grips feature a thicker design that dampens vibration. The soft shoulder allows ease of movement. Three wire-tie grooves are molded into the grip to make securing them a breeze. We think they are great!

ProTaper Pillow Top Grip with 3-D (Tri-Density) Technology.  Try the grip with the technical advantage of three dedicated rubber compounds.

• Vibrasonix pillow top reduces vibration and cushions impact. 
• Inner core compound perfects the bonding interface with bars. 
• Anti-Rip Tip™ uses denser compound to increase life of grip. 
• Designed to self-clean and shed mud away from outer surface. 
• Tacky gel-like surface compound is perfect for the trail and MX.

ProTaper Pillow Top Grip with 3-D (Tri-Density) Technology.  Try the grip with the technical advantage of three dedicated rubber compounds.

The difference between the original Pillow Top and the Pillow Top Lite is the overall diameter of the grip surface. The Lite offers a smaller diameter so the grips don't feel as large reducing fatigue in your hands while riding.

• Vibrasonix pillow top reduces vibration and cushions impact. 
• Inner core compound perfects the bonding interface with bars. 
• Anti-Rip Tip™ uses denser compound to increase life of grip. 
• Designed to self-clean and shed mud away from outer surface. 
• Tacky gel-like surface compound is perfect for the trail and MX.

Each pattern is available in three advanced synthetic rubber compounds. This means you can have the optimum combination of strength, tackiness and shock absorption to suit every riding condition and individual style. Soft grip is extremely soft, giving you a very comfortable ride, great feel and reduces the chance of blisters; however, because the grip is so soft, it wears quickly. Medium is a compromise between firm and soft. Firm grip has the same feel as a stock grip, it is very strong and has very good resistance to tearing and abrasion. Half Waffle has waffle pattern in finger area for traction and diamond pattern on palm side to reduce blisters. Full Waffle: designed after the CR Honda® grip.

This little jewel reduces hand fatigue and cramping on long rides or daily commutes. The Crampbuster is not a throttle locking unit but, rather a simple clip-on device which allows you to relax your grip while riding.

The Go Cruise cruise control mounts over the throttle grip and rests on the brake lever to hold your throttle open, allowing you to stretch and rest your hand on long rides. Installs and removes in seconds with no tools. You can roll off the throttle manually to disengage the Go Cruise.

• Machined and knurled 6061 billet aluminum
• Removable end cap for easy hand guard installation
• Works with standard housing

Opens your throttle 15% faster. No more 'double handfuls' to get it wide open. Removable end cap for bikes with hand guards.

OE style clutch or brake lever.

• Quality Aircraft grade A-360 aluminum for strength & durability
• Designed to exceed OEM specifications, built to resist breakage
• Durable hard coating
• Designed to fit OEM perch

Attach this over your brake lever and hand grip, squeeze the brake lever, pull the locking bar in and lock the black portion down. This creates a locked front brake, making parking safe and secure with about 5 seconds of effort.

To unlock the BrakeFix, you just lift the back of the black hooking portion to release it. This takes about 2 seconds. Perfect for use with Snapjack type stands or just parking on an incline.

The plastic fitting that secures the stock choke cable to the carburetor is delicate and easily broken. A broken fitting can cause hard to solve idling and running problems.

CNC machined from billet aluminum and anodized black or blue. If you want to retain your handlebar mounted choke this may be the solution.

  These no longer fit the new version of the ProCycle Remote Choke Cable. Will not work with the long or short reach choke knobs.

Throttle, Clutch or Speedo cables.

• Handy, compact kit for on-the-go emergency throttle, clutch and brake cable repairs
• Includes 2 different diameter 6.5 long inner cables and an assortment of cable ends

Bar end mounted mirrors move the mirrors out past your elbows so you can actually see what is behind you. They can mount with or without hand guards.

Sold in Pairs

This new mirror screws into your stock mirror mount but can be folded out of the way when it's time to hit the trails. These are quite similar to the very popular KTM folding mirrors but at half the price. Fits either left or right side.

Sold individually. 

  All Yamaha's will need a mirror adapter if you have the stock perch.

One folding mirror. Includes handlebar mount. Can be used on left or right side.

Sold individually.

This new mirror can be folded out of the way when it's time to hit the trails. These are quite similar to the very popular KTM folding mirrors but at half the price.

Fits either left or right side and includes handlebar mount.

Sold individually

With the split back, you don't need to remove your grip or throttle tube, just put it on and tighten 'er down. Put the mirror in and hit the road. Clean and simple.

Replaces all 2 bolt style clutch/brake lever mount clamps on your clutch or brake lever holder. Can help save space on short bend handlebars.

This adapter will give you more mirror choices.

Yamaha mirrors have reverse threads on the right (throttle) side of the handlebars. This adapter allows you to mount a mirror with standard 10mm threads on the right side of your handlebar. This opens up many options for your mirrors, choose any 10mm mirror for your Yamaha.

• Torque spec: 5 Nm

Can't see past your shoulders? These mirror extenders will get your mirrors higher and farther out for a much better view of the road behind you.

Sold individually.

The Adventure Kit is perfect for adventure and touring bikes where the mirrors are kept up most of the time. This mirror offers the widest field of view, and is ideal for riding paved and dirt roads.  The 6 inch arm is a little longer than anything else on the market, for great visibility on loaded bikes.

• Made from super tough glass reinforced zytel
• Reflector Dimensions: 5.25" x 3.5" (135mm x 95mm) 
• Overall mirror length: 7" (175mm) (not including arm mount)
• Convex lens meets SAE and CE specifications 
• Mirror mounts to any 10mm perch.

The new Doubletake ball is oversized, and high quality nitrile rubber surrounds an aluminum base that won't degrade under extended compression. 

The Doubletake Base Kit includes bolts to thread into every application (even reverse thread Yamaha's), without adapters. 

Sold individually.

The Trail Mirror is a simple solution for any dirtbike or mountain bike. Gives you hindsight when you need it, but you forget it's there otherwise. 

• Made from super tough glass reinforced Zytel
• Reflector diameter: 2" (50mm)
• Bar space: 0.75" (19mm), Height 1.25" (32mm)
• Convex lens for wider field of view

Zip ties directly to the bar- no hardware required.

Sold individually

PSR dual sport mirrors come with a slightly convex mirror for a wider field of vision behind you. The round mirror is 4.25" in diameter while the oval is 3.75" x 3". These mirrors are easily adjustable and fold out of the way quickly with the 1" RAM mounts.

The RAM Ball Stud Base used for both mirrors will go into any standard 10x1.25 threaded mirror base.

Sold individually. 

 All Yamaha's will need a mirror adapter if you have the stock perch.

Keep your cables lubed up and working freely, with Motion Pro's Cable Luber. This tool is used to inject lubricant into any cable housing. Clamps over housing and cable allowing an aerosol can with nozzle to be connected. Once the lubrication solution runs out the far end, the cable is lubricated.

Designed to seal completely around the cable housing and stop all those messy leaks. With the unit closed and sealed around the cable, your cable gets better lubrication and you waste less lubricant.

• Works on most cables with a 4mm - 8mm O.D. housing.