Spring time is in full swing here at ProCycle. With these busy days please be sure to let us know if your order is time sensitive. We try to do as much as we can to accommodate your upcoming trip.
First there was the Warp 9 "4-Finger" Lever, now there is the Warp 9 "3-Finger" Lever Exclusive to ProCycle. Yep, the original shorty (next item below) is a full 4-finger type lever. These are a full half inch shorter. You asked for 3-finger levers, and we had Warp 9 make them for us. Brake lever includes a nice billet clamp with nylon sleeve to allow the assembly to rotate on impact. Will not fit with the stock OEM wind deflectors.
Will not engage the clutch switch on 2010 and later models
Front fender from ProCycle Plastics (formerly DSA) is shaped very much like the OEM DRZ400SM front fender. Big enough to be functional without wind-steering the bike like the stock fender does. Vacuum molded, these are a design improvement over stock. These are fully compatible in any combination with the original factory plastic.
Here is a complete kit to install oversized tapered 1-1/8" handlebars on your DR650. Warp9 handlebar clamps bolt to your stock triple clamp adding an additional 1" to the height.
Alloy oversize bars offer more durability and eliminate the crossbar which opens up your dash area for more goodies. Silver in color.
Galfer USA produces several different brake pad compounds for all types of riding styles and uses. With over 60 years of friction material production and research, they have learned that one compound doesn’t always do the trick across the board. If you are just looking for an OEM brake pad replacement or a high performance race brake pad, they have you covered!
Set includes front and rear brake pads.
Semi-Metallic Compound
OEM replacement upgrade. Great feel, long lasting, and very little rotor wear with this durable compound. Compound applications for almost every need, including off road, street, touring, enduro, dual sport and more. Precision made in our Galfer factory in Spain.
Our most popular compound! This compound is the work horse of the Galfer family and is a great OEM upgrade for the everyday rider.
This device will pulse your brake light automatically. There are over 1000 possible pattern combinations with individually programmable Flash Speeds, Pre-Delay, and Flash Durations, as well as a disable feature to disable the unit. This device gives the end user the widest range of possibilities for customizing your tail light safety flash. With simple programming setup using only your brake lever, their is no disassembly or removing of the seat required to change the programming on the device.
Features:
Independently programmable flash speed, flash duration, and pre-delay
This is a standard H4 bulb that has a 80 watt low beam and a 100 watt high beam. This is an easy lighting upgrade that should not over tax a stock charging system.
Includes all wheel bearings, new dust seals. The rear kit includes the bearing and seal for the cush drive hub (sprocket carrier). All bearings are sealed on both sides.
Low peg mounts for the DR From Wirtz Wire. These are different than our other mounts for several reasons. First, these are designed around the stock pegs. All of the pegs in this section will fit these mounts. Another difference is that these mounts are offered in a low mount as well as a low and rearward mount. These are 'wire EDM' machined from solid 1018 steel bar stock, and are not welded anywhere. They are powder coated black for a great look. Both mounts move the pegs down 2" while the low and rear mounts also move the pegs back 1.3".
Kit comes with new mounts, longer bolts and a longer brake switch spring that will be needed. Pegs are optional, your stock pegs will work.
The upper image shows the low and rearward mounts while the one below that is of the just low mounts. If you look at the two images below that, you will see that these are the low and rearward pegs for both sides of the bike.
ProTaper's ADV handlebars give you a bar taller than most with extra space on the control portion of the bar. These bars provide an additional 20mm of space next to where your levers and throttle are located for your GPS, phone cradle, auxiliary switches, etc . They come in Adventure (which is taller than stock) and Adventure High (which is even taller).
These are oversize bars, which means they are are 1 1/8", not the smaller 7/8" diameter. Therefore some bikes will require a adapter and there are several available to select from.
Using the same manufacturing techniques and materials as ProTaper’s industry-changing 1⅛" motocross handlebar, the EVO Adventure is specifically designed to provide adventure/touring riders with the increased comfort and control they need. With over 8" of straight section in the control areas, mounting vital components is made easier than ever. With its premium 7000 series aluminum alloy construction and computer-profiled four millimeter-thick wall design, the EVO Adventure Handlebar is up to 25% lighter and 45% stronger than competing handlebars.
1⅛" tubing at the clamping area
Exclusive 4 mm-thick 7000 series aluminum alloy for superior tensile and yield strengths
Optimum balance between fatigue life, impact strength, and impact-absorbing flex
High-tech shot peened, stress-relieved, and anodized finish for unmatched durability
Independent lab tests show that the EVO Handlebar leads the market in fatigue life
Epoxy inner coating resists corrosion
Chemically applied cut lines and alignment grid are scratch- and peel-resistant
Plastic bar end plugs keep the elements out and provide a stronger base for grip ends
Weighs only 1.55-1.7 lbs. (720-780 grams), depending on bend
Keeps the damper rod from turning so you can remove the bottom fork bolt. Perfect when replacing fork seals or installing cartridge emulators. It's a good addition to any tool box as it will fit many other bikes.
Designed and sculpted out of the best 7075 Billet aluminum by Pro Moto Billet elite engineers and machinists. Featuring Fastway's Patented adjustable height, traction, and camber options, the Evolution AIR footpegs are superior in every way. Fastway Evolution AIR pegs are designed to shed mud and debris, while being ultra strong.
You can also order serrated or spiked cleats separately.
These AIR pegs are offered in several colors, but some colors may require extra time, call for availability.
New from Warp 9. These top of the line Adventure pegs are 5" long and 2.5" wide. They will give your feet the perfect perch whether you are cruising down the highway or standing up hammering down a singletrack trail.
Ceracote coated Chromoly steel pivot for the ultimate in strength
Replaceable 7075 T6 Aluminum Platform
Permanent Stainless Teeth provide the ultimate in non-slip traction
Cogent Dynamics Mojave product is a drop-in replacement for the DR650 stock shock, no modifications necessary. Mojave is not simply an improved Suzuki shock, it is a brand new replacement shock that is a totally engineered suspension solution to suit your needs.
Each shock is assembled and tested on the Cogent Dynamics suspension dyno before being packed up and shipped. Like its bigger brother the Mojave Pro Series, this will make an incredible difference in the handling of your DR.
Mojave Improvements over stock Mojave upper mount: uses a precision spherical bearing with dust seals, which accurately transfers damping forces to the motorcycle frame.
Internal improvements: Cogent designed shaft, seal head, damper piston, adjuster and clevis. Mono tube construction: precision honed, super-stiff steel body with an upper body cap machined from billet aluminum. Built-in billet aluminum separator piston provides an in-line gas pressure reservoir which eliminates the Suzuki rubber bladder.
This shock package includes the CNC machined Bling Ring Preload Adjuster Collar and Preload Bearing that will make preload adjustments easy.
Select the spring you want installed based on the load you plan to carry. For riders (and gear) less than 250 pounds we recommend the 7.6 kg/mm spring. If you regularly have more than 250 pounds the bike, you might want to use the 8.15 kg/mm spring. If you have any questions at all about this, please call.
You may choose to add the Hydraulic Preload Adjuster to make it the easiest of all. All you do is twist the knob. Includes mounting bracket for knob unit. (Some CA carb compliant models may need slight modification for mounting the preload adjuster.)
Low shock also available. This option will lower your seat height 1" without the need for lowering links. All other features of this shock are the same as the stock height.
The Pro-Series is the suspension performance pinnacle. Cogent takes Mojave’s best-in-class performance and adds an external reservoir.
The Pro-Series’ sophisticated reservoir with interchangeable valves and shims, provides more tune-ability at all speeds. It also improves internal pressure balance and temperature dissipation, giving long lasting performance regardless of the punishment you put it through.
Comes standard with the CNC machined Bling Ring Preload Adjuster Collar and a thrust bearing between the adjuster ring and the spring making preload adjustments easy.
The optional Hydraulic Preload Adjuster makes it even easier to adjust the preload. Just twist the knob. Includes mounting bracket for knob unit. (See last image) (Some CA carb compliant models may need slight modification for mounting the preload adjuster.)
Select the spring you want installed based on the load you plan to carry. *Spring color may vary due to specification requirement and availability.
For riders (and gear) less than 250 pounds we recommend the 7.6 kg/mm spring.
If you regularly have more than 250 pounds on the bike, you might want to use the 8.15 kg/mm spring.
Low shock also available. This option will lower your seat height 1" without the need for lowering links. All other features of this shock are the same as the stock height.
CNC machined from 5mm aluminum 5083 plate with lots of slots to attach your Rok Straps (or other straps). This gives a considerably wider deck than the standard B&B Rack. Attaches directly to the B&B rack with four screws that are included. Available in either polished aluminum or a black polymer coating.
These plates are pre-drilled and countersunk from the bottom making installation of a RotoPax mount quick and easy.
Some older carry racks will not have predrilled holes in them to mount luggage plate in which it will require you to drill yourself (select pre2018 version)
This complete fork upgrade kit includes stiffer fork springs and Race Tech cartridge emulators, as well as a set of top quality fork seals and fork oil to complete the job. Everything you need to transform your mushy stock forks into suspension that really works.
You can select from various straight rate springs or even 'Progressive Suspension' springs to customize the package to your needs.
Rider and Gear up to 160lb. = 0.47 springs → 24% stiffer than stock
Rider and Gear 160-225 lb. = 0.52 springs → 39% stiffer than stock
Rider and Gear 255-275 lb. = 0.58 springs → 56% stiffer than stock
Rider and Gear 275-325 lb. = 0.63 springs → 66% stiffer than stock
Rider and Gear 325 lb.-UP = 0.70 springs → 84% stiffer than stock
Like all FunnelWeb filters, the ProLine Filter features profile cut, single layer, single density foam that doubles the external surface area of the filter without increasing the original filter size. The ProLine Filter traps dirt, dust, sand and mud over a larger area on its outer surface, ensuring optimal air flow is maintained for maximized engine performance and reliability.
The single layer, single density polyurethane foam has the added advantage of being easy to clean and the ability to maintain its original shape after numerous washes. Overall, compared with conventional foam filters, FunnelWeb offers more protection from dirt ingestion, has longer service intervals and maintains high airflow rates when dirty.
The RS-2 is a potent and versatile design that evolved from their original TRC, engineered to provide increased power delivery. With a different pyramidal shape that features increased volume, the RS-2 is a quieter system with a larger core — and it offers the added bonus of outstanding performance in a value-priced package.
Diamond-shaped sleeve
Large core and increased muffler packing volume means quieter operation
This Kit replaces vital components in the BST40 Carburetor including new a Float, Needle Valve, Gaskets, Seals, Diaphragm, Spring and Float Bowl Screws to return the stock Mikuni BST40 Carburetor to like-new operation. As a bonus we have included Viton o-rings for the float assembly and 4 stainless steel allen screws.
10.5:1 compression JE piston with rings, wrist pin and circlips (the actual measured stock compression is only 8.7:1). Stage 2 Web Cams high performance camshaft for more power (reground from brand new OEM Suzuki camshafts). Top end gasket set with metal base gasket.
We strongly recommend checking valve to piston clearance when installing a non-standard camshaft.
4 custom made valves and 4 'Nickel Aluminum Bronze' valve seats. Valve sizes are 36mm intake (up from 32) & 32mm exhaust (up from 28). Requires professional installation.
We strongly recommend checking valve to piston clearance when installing oversized valves.
This Kit replaces vital components in the BST40 Carburetor including new o-rings, gaskets, jets, needle, mixture screw, float bowl screws, float valve needle and seat (needle jet and other pressed in jets are not included in kit) to return the stock Mikuni BST40 Carburetor to like-new operation. As a bonus we have included Viton o-rings for the float assembly and 4 stainless steel allen screws.
The Remote Fuel Mixture Screw is 5 inches longer than stock. This gives you plenty of length to easily mount in a convenient location. Will work with the stock BST Carburetor as well as the TM40 pumper Carburetor.
This should be the last oil filter you will ever buy. Made from laser cut, medical grade, 304 stainless steel micronic filter cloth, this filter provides 200% more filter area than other filters in many cases. Most good paper filters will pass particles in the 90 to 95 micron range, and some tested, as much as 300 microns. Sand is about 125 microns and a white blood cell approximately 25 microns. Scott's stainless filter catches items down to 35 microns "absolute". The pleat seam is welded, able to withstand up to 600 degrees, not glued, like paper filters.
This kit of O.E. Suzuki O-rings replaces your leaky, weepy, and brittle O-rings that fit between your DR's oil cooler lines. You get 4 O-rings in this kit to replace both feed and return line O-rings.
If you're noticing oil leaking or creeping around your oil cooler, oil cooler lines, or engine, you may have one or more failed / failing oil cooler line O-rings. Replace them now before they completely fail and you run your motor dry of the precious oil it needs to operate properly.
Light weight and strong. These DRC foot pegs have a wider platform for increased comfort and control. Cast from Chromoly steel for unbeatable strength and durability.
Extended float bowl screws from Wirth Machine for your OEM BST carburetor that use 5/6" or 8mm size wrench to loosen. Allowing easy access to your jets and float without having to remove the carburetor from the bike. Sold in a 2 pack. Stainless steel threads.
Genuine SKF wheel bearings. Includes all wheel bearings, new dust seals. The rear kit includes the bearing and seal for the cush drive hub (sprocket carrier). All bearings are sealed on both sides.
The Warp 9 shift lever is black anodized and the Warp 9 logo is laser etched into the finish. Comes with a black anodized knurled aluminum tip that folds and returns via a stainless-steel return spring. Includes the pinch bolt as well.
These thumb-screws replace the stock headlight adjustment screws. These adjusters make it much easier to keep your headlight aimed properly. This is even more important if you are running the HID headlight as it is very easy to dazzle oncoming traffic if your headlight isn't aimed correctly.
Lost your side panel hardware? You aren't the first! We've got replacements. Two side panel screws, two special washers and the rubber insert that protects the side panel from the muffler.
Simple, quick installation of this 1 pound rack made from rugged 1/8" 5052 Aluminum. A rigid 4-point mounting system, but still sleek and low allowing for seat removal with no hassles.
Hand built aluminum luggage rack from the B&B Off Road Engineering folks down under. This unit really is a beauty to look at and extremely rugged, made from 4mm 5083 aluminum plate! Tie down whatever you need with confidence. Whether it's your books to get to school or a bag to get across the country, no worries mate. Available in either bare polished aluminum or with a black polymer coating.
While plenty rugged to use as grab handles, you can keep your stock handles if you so desire. All necessary stainless clamps and bolts are provided.
If you want a wider platform for support, consider adding the luggage plate to this rack.
Bike must have the DR250 Taillight installed to work with this rack.It will not work with the stock USA taillight.
Want an amazing increase in throttle response? More power over a much wider range? The Mikuni TM40 does all of that plus runs smoother at lower RPMs and pulls taller gearing with ease.
Our complete kit comes with alloy adapter rings bonded to the genuine TM40 carburetor body for a firm reliable fit in the stock air boots. We also include new low friction cables, an extended fuel screw, complete instructions along with a wide range of extra jetting for fine tuning. It even has a vacuum port for the stock fuel petcock.
The carburetor comes pre-jetted for the typical mods: performance pipe and modified air box, or we can set it up for your particular bike before we ship it out.
Instead of the tough to reach choke knob, all TM40's come with a remote choke and bracket. This makes it easier to reach the knob, especially if you have an oversize tank.
If you are adapting a GSXR or Hayabusa muffler to your DR650 you will need a fresh gasket that seals between the muffler and the mid-pipe adapter. There are two sizes depending on which OEM muffler you are using. The 4-bolt mufflers use the 2-1/2" OD seal ring. The 3-bolt mufflers use the 2-3/4" OD seal ring.
This gasket seals the joint between the head pipe and Exhaust port. These gaskets are designed to crush a little bit to tightly seal where the pipe fits to the head. Get a fresh one now avoid having an exhaust leak when you install your new exhaust.
An aluminum Light Mount for your bike. Put whatever light you like up front for more light as well as great daytime visibility to other vehicles. Win-win situation. Choose the Single Mount or Double Mount.
B&B Off Roads Auxiliary single light bracket is made from 5mm 5083 structural plate. It was designed to suit a 6 " light bar. Add an auxiliary bracket and LED light to help Improve visibility whilst night riding.
The PSR Oil Filler Caps are CNC machined from high quality aluminum and come with an E-clip that is already safety wired to a mounting tab. The wire is covered with silicone tubing that will not melt or discolor. Available in silver, black and gun metal.
Years in development, Yenkro Adventure Rally Fairings have been designed from the ground up to withstand even the most unforgiving terrain and now the gen 2 kit takes it to the next level. Battle-tested in conditions that only the Australian outback can muster, this fairing is a must for adventure riders from all corners of the globe.
Side Panels are Optional and Sold Separate, they work with Acerbis 6.6 gallon (25L) tank only. Available in either black or white.
Can be purchased with or without side panels.
Standard kit includes:
The main tower assembly with all the mounting brackets to suit your bike
Speedo bracket which also holds the stock wiring loom.
1 Short screen
1 Tall screen
Hella halogen lights (upgrade to led by adding the upgrade option to your cart)
Qc3 usb charge socket
Plug and play wiring for lights and usb.
The standard lighting kit is a pair of hella 60mm projectors, one for high and one for low, these are 60w halogens and are DOT and ADR approved.
Dual stage foam: 2 different pore sizes create more trapping area for even the smallest dust particles. Flame laminated foam: Both "Stages" are not glued but heat sealed to provide maximum air flow. Light color foam makes it easier to see where the filter oil has covered and where it has not.
We've been asking for a bigger tank for years and it's finally happened. This is the big brother to the very popular 5.3 gallon Acerbis tank with some modifications to add another gallon and a half of capacity. It's the same width between the knees but extends wider and further forward in front of the knee pockets. This high capacity fuel tank incorporates modern lines and high quality construction that can't be beat. Includes gas cap, petcock and all mounting hardware.
Installation of the Acerbis tank requires relocation of the front turn signals, otherwise the stock signals will contact the tank at full lock. Our Turn Signal Relocation Brackets move the front turn signals up and forward to clear the bigger tank.
These heavy-duty aluminum brackets are laser cut from 0.190" 5052 Aluminum then powdercoated black. Designed specifically for mounting auxiliary lights to the front of your DR650, the mount goes between the fender and the lower triple clamp. Longer fender bolts are included in each kit. installs in 10 minutes.
Three options are available: two different dual mounts that place the lights outside the fender and a single, center type mount. The 2" mount is for smaller type lights and is 8-5/8" between the mounting holes while the 3" is 10-3/8" between the mounting holes. If you are going to use larger style lights, the 3" mount is for you.
Note! The Dual 2" and 3" mounts do not work with the Acerbis 6.6 gallon tank! They make contact prior to full lock. Mounts are fine with other oversize tanks.
Heavy duty shock bumper. The stock bumper is prone to disintegrating with age. If you are re-valving your shock it's a good idea to be sure the bumper is in good shape.
The PowerBomb header promotes better flow by allowing a small expansion of the exhaust gasses. The 'bomb' also acts as a pre-muffler taking the edge off of overall sound levels. Includes clamp-on mounts for the stock heat shield. We recommend Anti-Seize on exhaust fasteners.
Ditch the stock ugly plastic sub-fender and install a B&B Off Road Engineering License Plate Holder. Comes with an LED light to keep the license plate lit up.
Get better range from your DR650 by adding an IMS 4.9 gallon fuel tank. Available in Natural, White, Black and Blue. Natural color is recommended if you wish to easily see the fuel level in the tank. Includes cap and fuel petcock.
For those people who have been wishing for a dual petcock setup for their Acerbis 5.3 and 6.6 gallon fuel tanks. Install this kit to get the last bit of fuel from the right hand side of the tank without tipping the bike on its side. Includes the right hand fuel valve, o-ring, screws, tee fitting, fuel hose and spring action hose clamps. You will have to drill the hole in your tank for the petcock standpipe. For Acerbis tanks only.
We worked with TechSpec to have them make custom tank grip pads that look great on both Acerbis (5.3 and 6.6 gal.) and IMS tanks. These pads not only cover those ugly scuffs, but give great knee grip to the slippery plastic.
These have been tested on two of our shop bikes for over 3 years, they did not bubble or peel off in any way.
The Trail Tech Vapor Speedometer/Tachometer units are custom designed for an exact fit. They feature a bright white backlit LCD display, waterproof connections, and all parts needed for a complete installation. These units accept AC and DC power input, and automatically switch to internal power if external power is removed. Power connectors are included. Permanent solid-state memory guarantees that data is never lost, even without power. Units are available in black.
Trail Tech provides a one year warranty and unlimited free phone and email support.
Unit functions:
Speedometer
Current Speed
Maximum Speed
Selectable MPH/KMH Display
Tachometer
Real-Time RPM Bar Graph
Numeric RPM Readout
Dual Programmable Shift Lights
Up to 20,000 RPM
Temperature
Ambient Temperature
Engine Temperature (liquid cooled only, optional air cooled sensors available)
This auxiliary light harness is specifically built for the DR650 using the highest quality materials and components. Wire lengths, component locations, and end terminals are all predetermined and assembled for you. No electrical expertise needed! The relay is wired directly to the battery and Posi-Tap connectors are used to tap in to the existing headlight high beam circuit.
This eliminates the need for a separate switch to operate your auxiliary lights. When your high beam is on, your auxiliary lights will be too. Back to low beam and those high-powered beams will be off so you don't bother oncoming vehicles. There's also an in-line fuse holder for safety and peace of mind. A simple one page instruction sheet is included.
Allows your bike to breathe much better giving you better response and performance.
Breather Filter
ProCycle Jet Kit which includes jets, needle, extended fuel screw, drill bits and Allen bolts to replace phillips (JIS) head bowl screws and detailed installation instructions
Choose Twin Air, DT1, or K&N filter with ProCycle filter wrap
OPTION - Twin Air breather filter (replaces standard breather filter)
Reproductions of the original DR650 factory turn signals. Save a bundle compared to the $70+ each cost of the OEM signals. The wire pigtails plug directly into the factory harness. No cutting or splicing necessary. Choose original style amber lens or clear lens with amber bulb.
Extra dirt protection for your K&N filter. Our custom made oiled-foam filter sleeve wraps snugly around the K&N filter to give a first layer of protection against dust and dirt. Oil it like you would any other foam filter.
New starters that are manufactured to meet or exceed OEM specifications. Pull out your old starter, put in this new one and go riding. These units are built to provide a longer life than the OEM unit with these features:
The armature is insulated for rust and corrosion protection
Rubber seals on the top and bottom of the unit ensure a dry operation
90/10 copper bushings
Extended shaft replaces long or short shaft OEM starters
The new DG RST (Reduced Sound Technology) muffler is the quietest DG muffler and is designed especially for dual-sport machines (Just 84db @ 3200 RPM). A new baffle design dissipates sound waves reducing noise output in a very efficient manner. This new design also stretches out the time between muffler repacks. Included is a Stainless Steel mid-pipe, USFS Approved Spark Arrestor and a new Aluminum end cap.
This is one of the toughest skid plates we've got. Manufactured from 3/16" aluminum that is laser cut and CNC formed, all joints are welded on both sides. The rear mounting bolts are fully recessed for protection. A welded block protects the bolt heads from being bashed and rounded from obstructions. Rubber isolators between the plate and the frame at these two bolt locations help to eliminate vibrations and keep noise down. Front mounts clamp around the frame for a solid connection.
The right side of the plate extends up to cover the oil filter and unbolts from the skid plate for easy filter changes. This skid plate has a black textured powder coat finish for great looks and durability. Includes stainless steel hardware.
This CNC cap will replace the stock gas cap on the stock tank. You do need some parts from the stock cap, so don't throw it away yet! It is not difficult and this kit includes the additional hardware required. Also included is a vent tube with a matching cap.
For use on STOCK TANK ONLY! This is NOT a locking cap.
Does not fit California model DR650
New from the folks at Warp 9, a CNC billet machined Oil Filler Cap. Available in Blue or Black and it includes a new O-ring! To make removal as easy as possible, the center tab takes a 12mm wrench perfectly, or a 1/4" ratchet drive in the center! On each end of the center tab is a drilled hole should you find it necessary to safety wire your filler cap in place.
The complete shock upgrade kit - a shock spring of your choice, Race Tech Gold Valve kit, detailed instructions and a bottle of quality shock oil to complete the job. Everything you need to transform your mushy stock shock into suspension that really works.
Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
Ride in warm temperatures a lot? Worried about your motor oil just getting too hot? The Trail Tech Universal Fan Kit mounts up to the backside of the DR's oil cooler to draw cool air across it and keep those oil temps down. An electronic temperature sensor mounts to the fan, no need to cut any fluid lines, and automatically turns the fan on when needed to keep the temperature in the optimum range.
The activation sensor can be set wherever you like to keep the temperature right where you want it. Backlit for easy viewing anytime it also includes a volt meter.
If you are replacing your side stand you will want to check the hardware. Over the years they can take a beating and the springs become lost or broken.
This is the full kit that includes #4, #5, #2, and #3 in the diagram.
If you need a replacement cap for your Acerbis tank, why not go bling? These caps have a carbon fiber pattern molded into them that is extremely realistic. Looks like the real thing. Topping off the cap is a CNC Machined metal vent cap. This eliminates the need for a lengthy vent tube that gets in the way. The vent cap allows air to vent into the tank but does not allow fuel to splash out during normal use or during a tip over.
This kit includes the all new Morimoto 4×6 LED headlight and pre-assembled JNS Engineering adjustable mounting bracket set. It’s a plug and play installation however a small amount of trimming on the backside of the plastic headlight shroud is required.
This is the best performing and highest quality headlight they currently offer. The low beam pattern is bright, very uniform, and features a proper upper cut-off (Left Hand Drive). The high beam is amazingly bright eliminating the need for auxiliary lighting.
The materials, construction, and aesthetics are all top notch. You won’t be disappointed.
Low Beam: 20W, 2,400 Lumens
High Beam: 35W, 4,300 Lumens
Color Temperature: 5,000k
DOT Compliant
Beam Pattern: Left Hand Drive
If you just installed aftermarket LED turn signals or an LED integrated tail light and your turn signals are flashing way too fast, or perhaps simply staying on completely, you're at the right place to find the solution! The TST Gen2-SK LED Flasher Relay fixes what we call "hyperflash". It slows the flash rate down to a pre-set 85 cycles per minute but can be sped up or slowed down using the adjustment dial located within the unit so you can get the exact speed you are looking for. The plug-and-play installation means that you don't need to splice in any load balancing resistors that generate unnecessary heat and require splicing into your stock wires. Simply remove the stock relay and install your new TST relay and your wiring job is done. It's that simple!
Slows turn signal flash rate down to an adjustable 85 cycles per minute when turn signals are experiencing hyperflash or stay on continuously
Adjustable turn signal flash rate enables you to speed up or slow down the flash rate to fit your preference
Plug and play installation meaning no cutting, splicing, or soldering
Replaces the stock relay and fits like OEM
No need for cumbersome and heat-generating load balancing resistors
Flexible relay housing enables easy access to the flash rate adjustment dial inside of the relay unit
Please make sure your bike uses a 2-pin relay for the signaling system. If your bike has hazard lights it may need the 4-pin relay. Please also note the pin configuration and make sure it matches what is on your bike. It is very important to verify fitment before making your purchase.
