Spring time is in full swing here at ProCycle. With these busy days please be sure to let us know if your order is time sensitive. We try to do as much as we can to accommodate your upcoming trip.
A stainless steel front fender brace. Helps stabilize your front fender.
Gives additional strength for carrying a fender mounted tool bag.
Fits on top of the fender and bolts between the fender and bottom triple clamp. Stainless steel won't rust or corrode. Includes hardware.
Requires you to drill one hole in the fender for mounting.
A real Heavy-Duty Chain Guide manufactured from 5mm (3/16") thick 5052 Aluminum. This guide will take a pounding and continue to put that chain right on the sprocket. The rub block is machined from UHMW plastic and can be positioned to fit just about any sprocket available for the DR. These are powder coated black for a great look and additional protection.
Front fender from ProCycle Plastics (formerly DSA) is shaped very much like the OEM DRZ400SM front fender. Big enough to be functional without wind-steering the bike like the stock fender does. Vacuum molded, these are a design improvement over stock. These are fully compatible in any combination with the original factory plastic.
The ProCycle rack system is designed and manufactured by dual sport riders that know what it takes to create a durable and versatile luggage rack.
Our racks allow for easy installation of both soft and hard luggage.
See the linked instructions for how-to videos.
First there was the Warp 9 "4-Finger" Lever, now there is the Warp 9 "3-Finger" Lever Exclusive to ProCycle. Yep, the original shorty (next item below) is a full 4-finger type lever. These are a full half inch shorter. You asked for 3-finger levers, and we had Warp 9 make them for us. Brake lever includes a nice billet clamp with nylon sleeve to allow the assembly to rotate on impact. Will not fit with the stock OEM wind deflectors.
Will not engage the clutch switch on 2010 and later models
Designed and sculpted out of the best 7075 Billet aluminum by Pro Moto Billet elite engineers and machinists. Featuring Fastway's Patented adjustable height, traction, and camber options, the Evolution AIR footpegs are superior in every way. Fastway Evolution AIR pegs are designed to shed mud and debris, while being ultra strong.
You can also order serrated or spiked cleats separately.
These AIR pegs are offered in several colors, but some colors may require extra time, call for availability.
The RS-2 is a potent and versatile design that evolved from their original TRC, engineered to provide increased power delivery. With a different pyramidal shape that features increased volume, the RS-2 is a quieter system with a larger core — and it offers the added bonus of outstanding performance in a value-priced package.
- Diamond-shaped sleeve
- Large core and increased muffler packing volume means quieter operation
- Stainless steel cone end-cap
- Stainless steel tail-pipe
- USFS Approved spark arrester included
- 6.8 lbs lighter than stock
We recommend Anti-Seize on exhaust fasteners
The EXP disk is the magic ingredient behind the functionality and benefits of Rekluse auto clutches. About 10 years ago, Rekluse introduced an innovatively redesigned version of its revolutionary auto clutch technology with EXP 3.0. The years of racing, testing and development since have led to Rekluse’s most refined auto clutch experience yet; Introducing EXP 4.0.
No More Stalling:
Using principles of centrifugal force, EXP technology automatically engages and disengages the clutch based on engine RPM. With EXP, riders can start and stop without touching the clutch lever. EXP automatic clutch technology provides riders precision throttle control, maximum traction and confidence to maneuver any obstacle on the track, trail, or road.
Less Arm Fatigue:
You don’t have to clutch as often, which preserves your arm for longer rides.
Tunable to Fit Your Riding Style:
Each auto clutch is optimized for each bike model as it comes from the factory, and EXP 4.0 has been developed and tested in a wide range of late-model motorcycles. However, everybody rides differently, so they made sure EXP technology can be fine tuned. They offer different spring and wedge options so riders can further adjust their clutch’s performance. Some riders like the clutch to engage just above idle, while others like later engagement.
Clutch Lever Is Still Functional At All Times:
It is possible to fully override the auto functionality at any time. You can pull the lever in, build RPMs, pop the clutch out and raise the front tire just like normal.
Have More Fun:
You don’t have to worry about covering your clutch to prevent stalls all the time. You are free to relax and enjoy the ride, having one less thing to think about.
PMR side utility racks are great for strapping down your soft luggage and keeping it off the rear plastics and exhaust pipe, while adding plenty of new tie down points for any luggage you have on your seat or tail section. They also add an enhanced level of security and strength to the rear end of your motorcycle in the event of a tip over or crash.
Sold as a pair. Easy to Install
- Complete with all necessary mounting hardware
- Fabricated with 1/2 inch steel tubing, MIG welded
- Finished with a semi gloss black industrial grade powder coat
- Comes with left and right side racks, each side weighs 2 lbs
Cogent Dynamics Mojave product is a drop-in replacement for the DR650 stock shock, no modifications necessary. Mojave is not simply an improved Suzuki shock, it is a brand new replacement shock that is a totally engineered suspension solution to suit your needs.
Each shock is assembled and tested on the Cogent Dynamics suspension dyno before being packed up and shipped. Like its bigger brother the Mojave Pro Series, this will make an incredible difference in the handling of your DR.
Mojave Improvements over stock
Mojave upper mount: uses a precision spherical bearing with dust seals, which accurately transfers damping forces to the motorcycle frame.
Internal improvements: Cogent designed shaft, seal head, damper piston, adjuster and clevis.
Mono tube construction: precision honed, super-stiff steel body with an upper body cap machined from billet aluminum.
Built-in billet aluminum separator piston provides an in-line gas pressure reservoir which eliminates the Suzuki rubber bladder.
This shock package includes the CNC machined Bling Ring Preload Adjuster Collar and Preload Bearing that will make preload adjustments easy.
Select the spring you want installed based on the load you plan to carry. For riders (and gear) less than 250 pounds we recommend the 7.6 kg/mm spring. If you regularly have more than 250 pounds the bike, you might want to use the 8.15 kg/mm spring. If you have any questions at all about this, please call.
You may choose to add the Hydraulic Preload Adjuster to make it the easiest of all. All you do is twist the knob. Includes mounting bracket for knob unit. (Some CA carb compliant models may need slight modification for mounting the preload adjuster.)
Low shock also available. This option will lower your seat height 1" without the need for lowering links. All other features of this shock are the same as the stock height.
This device will pulse your brake light automatically. There are over 1000 possible pattern combinations with individually programmable Flash Speeds, Pre-Delay, and Flash Durations, as well as a disable feature to disable the unit. This device gives the end user the widest range of possibilities for customizing your tail light safety flash. With simple programming setup using only your brake lever, their is no disassembly or removing of the seat required to change the programming on the device.
Features:
- Independently programmable flash speed, flash duration, and pre-delay
- Works for LED or Standard Bulb Tail Lights
- All Solid State design
- Meets or exceeds OEM load rating specifications
- Over 1000 possible flash pattern combinations
- Simple programming setup with your brake lever
- Extremely compact unit size; 20mm x 20mm x 12mm
Low peg mounts for the DR From Wirtz Wire. These are different than our other mounts for several reasons. First, these are designed around the stock pegs. All of the pegs in this section will fit these mounts. Another difference is that these mounts are offered in a low mount as well as a low and rearward mount. These are 'wire EDM' machined from solid 1018 steel bar stock, and are not welded anywhere. They are powder coated black for a great look. Both mounts move the pegs down 2" while the low and rear mounts also move the pegs back 1.3".
Kit comes with new mounts, longer bolts and a longer brake switch spring that will be needed. Pegs are optional, your stock pegs will work.
The upper image shows the low and rearward mounts while the one below that is of the just low mounts. If you look at the two images below that, you will see that these are the low and rearward pegs for both sides of the bike.
The Pro-Series is the suspension performance pinnacle. Cogent takes Mojave’s best-in-class performance and adds an external reservoir.
The Pro-Series’ sophisticated reservoir with interchangeable valves and shims, provides more tune-ability at all speeds. It also improves internal pressure balance and temperature dissipation, giving long lasting performance regardless of the punishment you put it through.
Comes standard with the CNC machined Bling Ring Preload Adjuster Collar and a thrust bearing between the adjuster ring and the spring making preload adjustments easy.
The optional Hydraulic Preload Adjuster makes it even easier to adjust the preload. Just twist the knob. Includes mounting bracket for knob unit. (See last image) (Some CA carb compliant models may need slight modification for mounting the preload adjuster.)
Select the spring you want installed based on the load you plan to carry. *Spring color may vary due to specification requirement and availability.
For riders (and gear) less than 250 pounds we recommend the 7.6 kg/mm spring.
If you regularly have more than 250 pounds on the bike, you might want to use the 8.15 kg/mm spring.
Low shock also available. This option will lower your seat height 1" without the need for lowering links. All other features of this shock are the same as the stock height.
Not only are Pro Moto Billet Cargo Racks brutishly strong and functional, but they look great too. Each cargo rack is methodically engineered, then CNC machined on-site from a 1/2 inch thick plate of USA made 6061 aluminum by master machinists.
The cargo racks are then hard clear anodized for durability. PMB uses only stainless steel fasteners for worry-free years of riding. Excellent instructions and all necessary hardware is included. 10.5"Wx11.5"L
Need to mount your turn signals to your new Pro Moto Billet Rack? Just add a set of CNC machined aluminum Turn Signal Brackets.
Increase your fuel and/or water carrying capacity. This mounting plate attaches to the OEM Suzuki rear rack and accepts the standard RotoPax mounting pedestal. The use of pressed-in threaded mounting hardware allows for quick and easy installation of the plate and pedestal. When not needed the RotoPax pedestal can be quickly removed and the tidy JNS mounting plate left in place.
- 0.125" 5052 Aluminum, Laser cut / CNC formed
- Powder coated black
- Includes stainless mounting hardware
Order alone or with RotoPax Mount and Water or Fuel container. Get everything you need at one time.
The ProCycle seat was designed for both comfort and function. Our seat is built with a premium denser foam for those long days in the saddle also giving you freedom to move while standing.
- Wide and firm saddle adds comfort on long rides
- Narrowing taper up front allows room for knees when standing
- The vinyl weave pattern allows airflow between you and the seat
- Provides grip down the sides allowing you to hold on with your knees
We will build the seat for you in house on a new seat pan so all you have to do is put it on and go ride.
Choose the heated seat option and we will add a Seat Warmer during the build process.
The ProCycle side rack is designed and manufactured by dual sport riders that know what it takes to create a durable and versatile luggage rack.
Our racks allow for easy installation of both soft and hard luggage.
Side racks only, top rack sold separate.
Compatible with the following top racks:
- ProCycle
- Pro Moto Billet
- Pat Walsh
- Nomadic
- TCI Borrego
- Stock Suzuki (must grind 1/8" off inside of frame mounts)
ProCycle rack installation requires removal of the stock grab bars. Turn signal brackets will be needed if using a top rack that doesn't offer turn signal mounting holes.
Construction
- 5/8" steel tubing
- Computer precision bending
- Durable powder coat finish
- CNC cut brackets
- All mounting hardware included
Formerly DSA, now ProCycle brand, is a plastics kit in three colors - Black, White, and Blue, as well as Blue fenders with White side panels and Black fenders with White side panels. (headlight cowl not included).
Vacuum molded, these parts are a design improvement over the stock pieces. The side panels have a crisper, more angular look than the stock parts while the front fender is shaped like the DRZ400SM OEM front fender. Big enough to be functional without wind-steering the bike like the stock fender does.
Kits include front and rear fenders, a new LED tail/brake light and license plate holder, and both side panels.
Add a fresh new side panel hardware kit and an adhesive heat shield for a fresh off the showroom floor look.
Add a stock Suzuki headlight cowl if you are doing a complete color change to your DR (must select plastic kit with head light cowl option)
These tips are for the Warp 9 Shift Levers only. These are held to the cast Warp 9 lever with a pin and e-clip making them easy to change out. Includes new pin and e-clip in case you lose yours.
You can also order just a new pin hardware kit which comes with new pin and clip.
GoldPlug is the gold standard in engine protection.
Stainless steel drain plug with an extremely strong magnet that picks up metal flakes in your oil.
14mm Thread
Our very own high flowing head-pipe is made in the USA using a CNC (computer numerically controlled) mandrel bender for an absolute perfect fit. It is a high quality 2-piece 18 gauge stainless steel head-pipe with 1 3/4" outer diameter, compared to the stock outer diameter of 1 1/2".
The SS Pro-Flow is a tested upgrade over stock that will bolt right on with no modifications needed. It is compatible with any combination muffler/mid-pipe, as well as all motor configurations of the DR650 '96-current.
Includes a stainless steel band clamp for the mid-pipe joint, clamp-on heat shield mounts, to use with stock heat heat shield and a stainless steel flange at the exhaust port mount. We recommend a new exhaust gasket when installing your new SS Pro-Flow.
The Powercore 4 spark arrestor muffler. FMF developed the Powercore 4 to increase the horsepower and torque throughout the entire power curve. Highest quality packing for long life. Removable spark arrestor included. Louder than the Q4. Approximately 99db stock or about 94db with optional Quiet Insert installed.
- Uses long-life muffler packing for increased packing life
- Forest Service approved spark arrester
If you are converting a Keihin FCR-MX 39 to fit on your DR, you need to start here. This 6061 T6 aluminum adapter bonds to the airbox side of the carb so it will easily fit the DR.
Not for the stock carburetor Fits FCR-MX conversions only.
New Hot Shot Suzuki Stator: aftermarket stator is made with heavy duty components and is a direct replacement for OE# 32101-32E01 or 32101-32E00.
This stator will provide your bike with 20% more power to support your added gear. Whether you have heated grips or you're running multiple aux lights, this unit will give you the power that you're looking for.
An excellent replacement for the stock fork boots. These are great for protection from dirt, rocks and other contaminants. These boots utilize the latest advances in material technology to adapt to fork and styling demands. These high quality fork boots are 1/4 the price of the OEM factory replacements.
Choose black, blue or yellow.
Sargent's proprietary seat foam is their own unique blend of resilience, firmness, and vibration-absorption qualities - making it well suited for maximum long distance comfort. Available in standard height and 1" lower than stock. These seats will fit bikes with the stock, IMS, or other any aftermarket fuel tank.
These thumb-screws replace the stock headlight adjustment screws. These adjusters make it much easier to keep your headlight aimed properly. This is even more important if you are running the HID headlight as it is very easy to dazzle oncoming traffic if your headlight isn't aimed correctly.
- Sold in pairs.
Simple, quick installation of this 1 pound rack made from rugged 1/8" 5052 Aluminum. A rigid 4-point mounting system, but still sleek and low allowing for seat removal with no hassles.
Features:
- 12" long by 10" wide
- Integrated turn signal mounts
- Use with or without stock grab handles
- 16 strap slots for securing cargo
- RotoPax mounting kit compatible
- All hardware and instructions included
These heavy-duty aluminum brackets are laser cut from 0.190" 5052 Aluminum then powdercoated black. Designed specifically for mounting auxiliary lights to the front of your DR650, the mount goes between the fender and the lower triple clamp. Longer fender bolts are included in each kit. installs in 10 minutes.
Three options are available: two different dual mounts that place the lights outside the fender and a single, center type mount. The 2" mount is for smaller type lights and is 8-5/8" between the mounting holes while the 3" is 10-3/8" between the mounting holes. If you are going to use larger style lights, the 3" mount is for you.
Note! The Dual 2" and 3" mounts do not work with the Acerbis 6.6 gallon tank! They make contact prior to full lock. Mounts are fine with other oversize tanks.
This kit includes a 320mm Wave rotor, caliper relocation bracket and new Galfer semi-metallic brake pads.
You can add a Stainless Steel brake line, and DOT4 fluid to your package.
This is one of the toughest skid plates we've got. Manufactured from 3/16" aluminum that is laser cut and CNC formed, all joints are welded on both sides. The rear mounting bolts are fully recessed for protection. A welded block protects the bolt heads from being bashed and rounded from obstructions. Rubber isolators between the plate and the frame at these two bolt locations help to eliminate vibrations and keep noise down. Front mounts clamp around the frame for a solid connection.
The right side of the plate extends up to cover the oil filter and unbolts from the skid plate for easy filter changes. This skid plate has a black textured powder coat finish for great looks and durability. Includes stainless steel hardware.
We worked with TechSpec to have them make custom tank grip pads that look great on both Acerbis (5.3 and 6.6 gal.) and IMS tanks. These pads not only cover those ugly scuffs, but give great knee grip to the slippery plastic.
These have been tested on two of our shop bikes for over 3 years, they did not bubble or peel off in any way.
A ProCycle exclusive. This is our favorite air filter for the DR650. Made just for us by the folks at DT1.
- Unique triple stage foam filter designed for the most extreme conditions
- Increased protection against silt, water, and sand
- Allows for extended filter service intervals
- Neoprene base gives superior sealing to air box
- Includes resealable bag for easy oiling and storage
NoToil cleaner NOT recommended with this filter. May cause delamination.
Dual stage foam: 2 different pore sizes create more trapping area for even the smallest dust particles. Flame laminated foam: Both "Stages" are not glued but heat sealed to provide maximum air flow. Light color foam makes it easier to see where the filter oil has covered and where it has not.
The PowerBomb header promotes better flow by allowing a small expansion of the exhaust gasses. The 'bomb' also acts as a pre-muffler taking the edge off of overall sound levels. Includes clamp-on mounts for the stock heat shield. We recommend Anti-Seize on exhaust fasteners.
DG Performance exhausts help your engine breathe better, resulting in increased throttle response, power and torque.
The V2 Series Slip-On muffler features:
- Lightweight aluminum body
- Stainless steel inlet tube
- TIG welded components
- Great new look
Standard sound level is approximately 98 db and quiet core inserts are available separately.
This Lightweight Slip-On weighs approximately 5.5 lbs and bolts directly to the stock headpipe.
It is equipped with a US Forest Service-approved spark arrestor.
This auxiliary light harness is specifically built for the DR650 using the highest quality materials and components. Wire lengths, component locations, and end terminals are all predetermined and assembled for you. No electrical expertise needed! The relay is wired directly to the battery and Posi-Tap connectors are used to tap in to the existing headlight high beam circuit.
This eliminates the need for a separate switch to operate your auxiliary lights. When your high beam is on, your auxiliary lights will be too. Back to low beam and those high-powered beams will be off so you don't bother oncoming vehicles. There's also an in-line fuse holder for safety and peace of mind. A simple one page instruction sheet is included.
Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
Progressive Suspension springs offer a soft initial spring rate for a plush ride. Progressively wound design provides increased resistance to bottoming as spring compresses. These springs are significantly stiffer than the wimpy stock springs. Spring rate spans the .45-.62 kg/mm range.
Sold in pairs
Our ProCycle top rack is designed and manufactured by dual sport riders that know what it takes to create a durable and versatile luggage rack.
Our racks allow for easy installation of both soft and hard luggage.
- 5/8" steel tubing
- Computer precision bending
- Durable powder coat finish
- CNC cut brackets
- Top rack dimensions 15" wide 11" long
- Top rack has RotoPax and hard case mounting tabs
- All mounting hardware included.
Top rack only, side racks sold separate.
These Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. These units have been given the seal of approval by the ProCycle staff for both performance and ease of installation. No disassembly of your forks, no drilling of damper rods. Just change the oil over to 5w and install the DDCs under the springs and hit the trails.
Warp 9 Supermoto wheels are built with billet hubs, 7000 series aluminum rims and laced and trued with stainless steel spokes and nipples.
The 3.5" x 17" front wheel includes a 320mm brake rotor and caliper relocation bracket.
The 4.25" x 17" rear wheel also comes with a rear brake rotor already mounted.
Add tires to your wheel order and we will throw in tubes and mount and balance them at no additional charge.
Rear wheel Includes Sprocket Carrier with 525 40T Sprocket installed that matches selected hub color.
Please allow 2-3 weeks for delivery.
Cannot be canceled.
Warp 9's CNC shark fin rear rotor protector. To make installation super-easy this fin bolts to a brand new CNC machined caliper bracket. Just remove your existing caliper bracket and remove the pins, install them on this new one and then put the caliper and fin back on.
Corbin seats are carefully designed to provide a comfortable riding position. They are firm and supportive which allows you to ride all day without fatigue unlike the stock seat.
Comfort Cell Foam retains resiliency and doesn't crush down like the stock foam so they can build a lower seating platform. This gives you better ground reach and a lower center of gravity. For the off-road enthusiast they were sure to leave enough nose to allow you to slide up the tank and get through the corners faster. Or slide back to skim the front end over the whoops.
The default vinyl choices are black 'carbon fiber' on top and 'asphalt' on the sides, 'no welts', black logo. You can view all of the available materials and colors through the link below. If you would like your seat built with something other than the standard choices please state specifics in the comments during check out.
Please allow 3 weeks
Cannot be canceled
Your choice of an aluminum bolt-on foot pad or a steel weld-on unit. Each will make the footprint of the stock side stand considerably larger, preventing your DR from tipping over in soft terrain. The bolt-on unit is cut from aluminum and then powder coated black, it comes with stainless steel mounting hardware.
The bolt-on pad and does require use of a drill for installation. The weld-on pad will need to be welded to the stand and then the entire unit painted for corrosion protection.
Low peg mounts from JNS Engineering. Your choice of a straight 1.5" drop or get that drop and a 1" rearward offset. You can use your stock pegs or click on one of the optional pegs that are made to fit the stock DR650 mounts.
These heavy duty steel mounts are pressed, welded and then powdercoated black for protection. Includes mounting bolts.
Note: These mounts are compatible with the SW Motech Center Stand by adding a 1/8" spacer behind the mounts.
Warp 9 has created a beautiful brake pedal machined from billet aluminum to an 8mm thick work of art. A stainless steel pin eliminates wear in the frame. This pedal has the ability to move the spring loaded brake tip 10mm either way from the center position. The arm is arched to provide clearance for riders who have the lowpeg + centerstand combination.
This is a high-quality seat cover offered by Moose for the DR650. This is a replacement cover only, no seat foam and you must install on your existing pan with existing foam.
- Heavy duty marine grade vinyl
- UV protected for long life
- Double stitched for durability
The ProCycle seat was designed for both comfort and function. Our seat is built with a premium denser foam for those long days in the saddle also giving you freedom to move while standing.
- Wide and firm saddle adds comfort on long rides
- Narrowing taper up front allows room for knees when standing
- The vinyl weave pattern allows airflow between you and the seat
- Provides grip down the sides allowing you to hold on with your knees
Available as a Foam and Cover Kit for OEM pan. It DOES NOT include the pan.
ProCycle side panel guards to keep your saddlebags from fouling the side covers. Constructed from mild steel tubing that is powder coated black for nice long lasting good looks.
Add Moose 20L Saddlebags for a very economical luggage solution.
Add Wolfman Rocky Mountain Expedition Saddlebags for a premium luggage solution.
Made from 1/8" thick stainless steel with dual folded edges for additional strength, these brackets will relocate your passenger pegs down 4" and move them back 1.5". This will give your passenger additional legroom making two-up riding much more comfortable.
All hardware is included for a quick and easy installation.
The 790cc Big Bore Kit includes a custom made, forged 9.5:1 piston with rings, wrist pin and circlips. A custom made multi-layer steel head gasket, OEM metal base gasket, tensioner gasket, and cam bolt lock plate and a ProCycle specific big bore cylinder sleeve.
Built cylinders with 790 sleeves installed are usually in stock, but we must have your original cylinder sent to us as a 'core'. These cores allow us to keep up this program and it is nothing more than an exchange - we give you ours, you give us yours.
This Kit Includes:
- DR790 Big Bore SLEEVE ONLY (requires your cylinder to be bored and sleeve pressed in. Your local machine shop is the best place to ask for this service.)
- Steel Base Gasket
- Steel Head Gasket
- Cam Sprocket Plate
- Tensioner Gasket
- 110.6mm DR790 Piston
- Instructions with DR790 Stickers
By popular demand. This is our own mid-pipe adapter kit for the GSXR exhaust cans. The unique design works with both 3-bolt Hayabusa and 4-bolt GSXR mufflers. It features all stainless steel TIG welded construction with a laser cut adapter. A spring tensioned slip joint allows for heat expansion. A stainless steel hanger strap allows it to attach to your original muffler mounting point. No welding is required. Mid-pipe length is approximately 17" long.
This mid-pipe does not require a stock muffler joint gasket when used with the stock headpipe, the SS Pro-Flow, or the FMF headpipe, eliminating the hump in flow.
Don't forget a fresh seal ring gasket that fits between your muffler and mid-pipe adapter.
Their rear racks are great for adding the extra storage needed for your next adventure. They are the perfect size for a backpack or small duffel bag. Their steel racks are built to handle any riding style you throw at them, now Rotopax ready!
This is the ENDURO Series DR650 rear rack which measures 10 inches wide and 12 inches long.
- Great for carrying cargo, duffel bags/backpacks, and mounting Pelican, Seahorse, or any other hard cases. Givi compatible.
- Holes are in place to accept Rotopax mount with no drilling required.
- Stainless steel mounting hardware and instructions included.
- Fabricated with mild steel, MIG welded, and finished with a semi gloss black industrial grade powder coat.
- Weighs 3 lbs, 10 inches wide, 12 inches long.
- Works with stock tool bag. You can remove the seat with no interference from the luggage rack.
- Rear rack only, no Rotopax mount or side racks included.
Transform your ride
MadStad's patented mounting system allows riders to adjust the height and angle of their motorcycle windshield resulting in much smoother airflow, better wind protection and a more comfortable ride than any fixed windshield can provide. Better still, this dual-sport version pivots the shield down and forward to get it out of your way for off-road riding!
What's included in the kit
Their complete bolt-on system is custom-made for your bike and includes everything needed to mount and position the shield. Your bike will not require any modification.
- A set of MadStad adjustable dual-sport brackets
- The acrylic windshield
The MadStad brackets bolt to the top of your fork clamps and are completely free of the handlebars. You can adjust the shield for the optimum height, angle and airflow for comfortable street and highway riding. When going off-road you can leave your comfort adjustment as-is and pivot the entire system down and forward in front of the headlight so you can get it out of your face completely. When it comes time to hit the pavement again, simply pivot it back up and you are back in street riding comfort mode.
The Rally windscreen from Parabellum is the perfect protection from wind and debris without sacrificing technical off-road capabilities. This is an upright rally type windscreen that looks aggressive and performs well under all types of riding. Designed primarily for the off-road / dualsport enthusiast, this shield keeps pressure off the rider's chest while commuting from home to adventure and back.
Mounting is accomplished by drilling two holes on each side of your headlight cowl using the provided template. The shield is 14 inches tall, 11.5 inches wide at the bottom narrowing to 8.5 inches at the top. Made from military aircraft grade cast acrylic.
This unit will not fit properly on '90 to '01 DR650 headlight cowls.
In the event of a crash or even just a dropped bike, these heavy-duty crash bars will prevent major damage.
The powder coated 1" steel tubing is bolted to the sub frame of the bike with two attachment points on each side, preventing them from rotating in the event of a low side.
The guards also feature aircraft grade aluminum plates that can be inexpensively replaced without needing to purchase a new set. Think of them as protection for your protection.
They use highest grade commercially available 12.9 (177,000 psi in tensile strength) wherever possible. Rest assured that you are getting the best material commercially available.
Most skid plates will require notching or modification to avoid interference.
Will not fit properly with oversized head pipes.
T-Rex Racing skid plate for the Suzuki DR650, designed to protect your bike from dirt, mud, and other debris.
Made from precision CNC machined aircraft grade aluminum finished with black powder coating for durability. Rest assured that you are getting the best material commercially available.
Specifically designed to work with T-Rex Racing engine guards, and center stand.
*Will not fit properly with oversized head pipes.
This new unit from JNS will protect your cases from the damage caused by a thrown chain, and will also keep your pants, boots or foot safe from your countershaft sprocket.
The case saver portion is laser cut from 0.25" aluminum and then has the 0.19" aluminum countershaft sprocket cover welded to it and the entire unit is powder coated black.
All the mounting hardware is stainless steel with machined aluminum spacers also included.
If you have a 16t front sprocket, mounting modification may be needed to fit. Install the case saver on the bike without the top spacer and bolt. This provides a little extra wiggle room. Add the top spacer and bolt after the bottom bolts are loosely threaded.
Replace your lost or broken stock plastic chain guard with a JNS aluminum one. Laser cut, CNC formed, TIG welded, and powder coated a beautiful satin black. This is a direct replacement for the stock unit.
Please note that this unit is a bit wider than the stock one and will have to be trimmed if you are running a big fat SuperMoto wheel/tire.
Molded using a very durable, lightweight 1/8" thick polycarbonate - giving the windshield a high impact strength and making it shatter-resistant with a superior light transmission quality. Mounts quickly and easily onto the stock headlight cowling for a clean factory look. Drilling of the cowling is required, hardware is included. Removal for trail riding is also quick and easy.
A popular upgrade from the stock vacuum operated fuel valve. Manually operated. Must be shut off any time the bike is parked for more than a few hours. Fits stock tank or aftermarket tank and has both main and reserve. Fully rebuildable.
ProCycle's 14 gauge stainless steel case armor to protect your engine cases. These case guards bond to your clutch cover and stator cover with high-temp silicone (not included). Extremely tough protection from rocks. In a fall your brake pedal or shift lever can crack the engine case - leaving you stranded. Don't let it happen to you.
Don't want to buy a new shock? This rebuild makes the stock shock about 10 times better. We send shocks to Cogent Dynamics. They clean them up, hard anodize the bodies for better wear, and install new Shock Shaft Assemblies with rebound damping adjustment.
Any aftermarket spring for your stock shock will fit on this shock. If you are using the original spring, you will want to order a stiffer spring to go with your new shock. Our 7.5 kg/mm rear spring is 16% stiffer than the stock one and is perfect for the majority of riders. If you are a larger rider, or carry a lot of gear or a passenger (total weight exceeding 250 pounds) you will probably want the 8.3 kg/mm rear spring which is 28% stiffer than stock.
Low shock also available. This option will lower your seat height 1" without the need for lowering links. All other features of this shock are the same as the stock height.
Please click on the link below for information on core charges and how to ship your shock to us. (If you select to add the core charge please include in the comments at checkout if store credit or refund is preferred)
Replacement side panels from ProCycle (formerly DSA). These pieces are fully compatible in any combination with the original factory plastic. These side panels have a crisper, more angular look than stock. Vacuum molded, they are a design improvement over the stock panels.
Sold in pairs
Does not include heat shield. Depending on your application and preferences, more than one optional heat shield may be useful.
We start with Excel or Sun rims, OEM or Warp 9 hubs, and Buchanan's heavy gauge stainless steel spokes. Rims and spokes are precision machined for a perfect match to your bike.
Our pro shop then laces and trues your wheels to perfection, giving you the highest quality set of custom wheels available.
- New OEM or Warp 9 hubs with bearings and seals installed
- Excel or Sun 3.5" x 17" front rim
- Excel or Sun 4.25" x 17" rear rim
- Buchanan's stainless steel heavy gauge spokes and zinc-plated nipples
Add tires to your wheel order and we will throw in tubes and mount and balance them at no additional charge.
Please allow 2-3 weeks for delivery.
Cannot be canceled.
Fastway offers a large ADV peg that is 4.75" long and 2.25" wide. With these pegs you can adjust the camber with their patented FKMS Kamber bolt. ´Tilt´ your pegs to increase comfort, or to give better squeeze on your bike. These pegs come with two sets of F3 cleats (one standard, one long). You can order serrated or spiked cleats separately.
These Adventure pegs are offered in several colors, but some colors may require extra time, call for availability.
Made of military aircraft grade 3/16" cast acrylic, this guard will protect your lens from roost, rocks and branches. Optical clarity of the acrylic ensures brightness and projection of your headlight are minimally effected while all the while protecting your headlight from impact and abrasion.
Guards are held to the headlight lens with an industrial strength hook and loop system on each corner.
A premium billet sprocket carrier from Warp 9 Racing that houses 2 bearings to help protect against the sideways twisting load that is commonly known to prematurely wear out the bearing and cush rubbers. This wear can cause extreme failure possibly damaging the hub.
Offered in anodized Silver or Black, Includes spacers and hardware.
These are only recommended to work on Warp 9 hubs.
Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a more plush and active ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.
These features combine to offer a custom seat feel, and provide greater enjoyment and increased range on a long commute, or Dual-Sport ride!
The Complete Seats come assembled with an aftermarket pan and ready to ride.
Width: | 13" (330mm) |
Height: | Same as OEM |
The Commuter shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but is much more dished out towards the mid-point to distribute rider weight over a greater area. the passenger platform has been built up to help prevent the passenger from sliding into the rider.
The Commuter seat is the best choice for extended pavement riding and mellow offroad. The unique shape and added width will provide greater enjoyment and increased range on a long commute, or Dual-Sport ride!
Lightweight, for reduced unsprung mass. Straight rate springs will give better control in the rough stuff. Sold in pairs.
- Rider and Gear up to 145 lb. = 0.47 springs → 24% stiffer than stock
- Rider and Gear 145-185 lb. = 0.52 springs → 39% stiffer than stock
- Rider and Gear 185-235 lb. = 0.58 springs → 56% stiffer than stock
- Rider and Gear 235-285 lb. = 0.63 springs → 66% stiffer than stock
- Rider and Gear 290 lb.-UP = 0.70 springs → 84% stiffer than stock
Our complete foot peg assemblies. 1-3/4" lower than stock. No extra brackets that hang down below the frame. Easier on the knees. Wider platform Yamaha YZ style footpegs are stronger and give you firmer footing. Mount solid to the frame. No more 'droopy' feeling when standing on the stock pegs. Lowering your footpegs makes it easier to stand and less of a reach down to the bars when standing.
Now you can get our Low Pegs with MK4 Pivot Pegz or black Fastway ADV pegs (both Yamaha YZ pegs) installed!
Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a more plush and active ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.
Complete seats are built by Seat Concepts on a new seat pan and come ready to be installed on your bike.
Width: | 10" (254mm) |
Height: | Same as OEM |
Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a more plush and active ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.
These features combine to offer a custom seat feel, and provide greater enjoyment and increased range on a long commute, or Dual-Sport ride!
Available as a Foam and Cover Kit for OEM pan.
Width: | 10" (254mm) |
Height: | Same as OEM |