Ultra bright amber LED turnsignals offer nearly the same visibility as OEM in a much smaller package. 15 amber LEDs in every signal. Flexible rubber stalks. Requires a LED turn signal to flash properly.
Pack of Two
These Sequential Turn Signals are available in a 2 pack or 4 pack short stem with 7 LEDs.
Matte Black, plastic body with smoke lens and 8mm mount bolt.
Specifications
Triangle/Teardrop style signals with LEDs. Mounts on any flat surface to keep out of the way of brush, branches, and your exhaust system. Requires LED flasher or LED turn signal resistors to flash properly.
This Diode Kit is only necessary if you have a single dash indicator for your turn signals. One dash light for both left and right signals (such as on the DR650).
This kit allows power to flow in just one direction from the LED signals to the dash indicator light regardless of which direction you are signalling.
You may have noticed after adding aftermarket turn signals (especially LED units) that your blink rate has significantly increased. OEM flashers are designed for standard bulbs which draw a few watts each, much more than typical aftermarket bulbs or LED signals. This device is an effective alternative to using load resistors because it consumes considerably less watts, consumes less space, and does not generate excessive heat.
The plug is exactly the same as the OEM unit making swap outs a cinch. No wiring changes, cutting and adding connectors. Just plug it in and you will have a steady flash at the DOT OEM rate regardless of what signal bulbs you use. It is an all solid state design and will blink correctly with loads all the way down to 0.1W / 0.01A.
Not for any DRZ400 or Royal Enfield Himalayan
This type of flasher is required for LED turn signals. For DC (battery) systems only. Includes 2 female connectors for universal fit.
Not compatible with any DRZ400
Works on AC and DC lighting systems
Not compatible with any DRZ400
This relay will fix your flash rate problem caused by aftermarket signal lights and/or integrated tail light. If your signal lights flash too fast or do not flash, this part is your solution! Plug and play - easy installation.
Only ONE relay is needed per motorcycle.
Features
This component works with the following signal configurations:
The SignalMinder unit is designed as a plug-in accessory for many Japanese bikes. SignalMinder uses a microprocessor to cancel the turn signals at one of three selectable time outs; 10, 20 or 30 seconds.
You can also make it so that all four of your signal lights also act as running lights and establish a dual-channel system on your bike. With the dual-channel system, when you activate the RIGHT turn signal three times in succession, you get 4-way hazard flash lights.
Connecting the 12 volt supply from the brakes to the SignalMinder, also allows for a brake flash option.
There are many options and configurations using this electronic tool.
No wire cutting required. The kit includes Scotchlok connectors to tap into existing wires.
Allows LED type turn signals (and low wattage flush mounts) to flash using a standard flasher unit. Connectors included. One kit works with 4 signals.
The Barkbusters 10 OHM Resistor Set for LED Indicator Lights will correct the flash rate of your auxiliary signal lights. Ready to plug in connectors make installation a breeze. These resistors are intended for Barkbusters LED Indicator Lights.
Features:
This devices allows any two wire after market LED turn signal indicators to operate as running lights (always on), and will blink on / off when the turn signal switch is activated. It is highly recommended to use this product with the Fixed Rate Turn Signal Flasher. This device, as well as aftermarket turn signals, use much less current than stock turn signals, thus an increased flash rate will occur. Load resistors or a fixed rate turn signal flasher will get your flashers operating at the normal flash rate again.
Each package contains two separate adapter boxes, good for operating both turn signals, left and right of either the front OR rear of your motorcycle. You will need to purchase a 2nd kit if doing the Front AND Rear of the motorcycle.
This device is universal; designed to work for any motorcycle with a DC electrical system. Kit comes with bullet connectors to wire in manually. Works with any two wire non-sequential aftermarket LED turn signal indicators.
Fits Most Models
These turn signal relocation brackets from ProMoto Billet provide an easy way to move the stock turn signal lights, useful if you find them getting in the way of your luggage configuration.
These brackets may utilize an existing hole in some of the rack side brackets, though many applications will require drilling or fabricating in order to mount properly.
Replacement Halogen bulbs for mini style turn signals. Sold in a pack of 5 bulbs.
Roll-up pouch ideal for tucking away your lights when out on the trail.
Taillight and brake light Attaches to the top of the rear fender. Dimensions: 3 1/2" wide x 2" long x 3/4" tall. D.O.T. approved.
LED powered taillight, brake light, license plate light & license plate mount. Attaches to the underside of MX style rear fenders.
Taillight, brake light, & license plate holder (no plate light). Attaches to the underside of MX style rear fenders. Small and good looking!
Taillight, brake light, & license plate light. Attaches to the top side of enduro style (XR, KDX, etc) rear fenders. Dimensions: 2 3/4" x 4 3/4" x 2 1/2" tall. Wiring instructions included.
Taillight, brakelight, turnsignals, license plate light & license plate mount. Taillight is DOT approved, turn signals are not. Attaches to the underside of MX Style rear fenders. Turnsignals are embedded in the taillight housing. Wiring instructions included.
*Flushmount signals may require resistors to flash correctly
Installing new turn signals or brake lights and need to find the 'HOT' wire, or are you just trying to find out if a specific wire has power going to it? Either way, this test light can help you locate shorts, open, and voltage on 12-24 volt DC circuits.
Has both high and low beams. Attaches to the upper fork tubes with rubber straps. DOT and CE approved.
Revolutionize your riding experience with Swiftkicker.
An adjustable kickstand for your motorcycle. Swiftkicker is built for offroad motorcycles, dual sports, and dirt bikes. Designed with the idea in mind that motorcycles should be able to take you anywhere, the Swiftkicker motorcycle kickstands help you do just that. You can set the length to anywhere in a six inch range of travel so you can stop anywhere without having to worry about having an even surface to park.
With just a flick of your toe, you can adjust the kickstand to the desired height, park your motorcycle, and be on your way.
No longer will you have to search for a rock or piece of wood to prop your motorcycle up with, or even worse, coming back to your bike to find it has tipped over from unstable ground.
The Swiftkicker is 100% manufactured in the USA from the highest quality components.
The billet 6061 head and the hard anodized tube are significantly stronger than the stock stand. An oversized foot will assure that the end of your stand stays where it belongs, rather than eight inches underground with your bike lying on top of it. The design is trail proven in the harshest possible conditions. Because nothing is indestructible, any of the kickstand components are replaceable at a lower cost than purchasing an OEM kickstand.
Measured from the center of the pivot to the bottom of the foot.
Your choice of an aluminum bolt-on foot pad or a steel weld-on unit. Each will make the footprint of the stock side stand considerably larger, preventing your DR from tipping over in soft terrain. The bolt-on unit is cut from aluminum and then powder coated black, it comes with stainless steel mounting hardware.
The bolt-on pad and does require use of a drill for installation. The weld-on pad will need to be welded to the stand and then the entire unit painted for corrosion protection.
Inexpensive way of getting the factory look. Adds 1/2" of width to any standard foot peg. These will give you a much more stable platform when standing on the pegs.
Sold in pairs.
Not your average rubber insert! These rubber covers go over the top of your MK3 or MK4 Pivot Pegz so that the aggressive teeth are only exposed when you need them in muddy conditions.
Important to verify which style Pivot Pegz you have before ordering.
Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm. Lo-pegs are down and back 1/4".
50mm step width provides better grip and control
Services two Pivot Pegz and fits MK2, MK3 and MK4 Pivot Pegz
Kit Contents:
Pivot Pegz have set a new standard in foot peg performance and quality and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty.
Pivot Pegz aim is to build the best foot pegs in the world and they really do perform as good as they look. There's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever.
New from Warp 9, top of the line Adventure Pegs. a full 5" long and 2.5" wide will give your feet the perfect perch whether you are cruising down the highway or standing up hammering down a single track trail.
NOTE: These pegs DO NOT fit the '18 model!
Tapered roller bearings provide decreased maintenance, less wear, smoother operation and longer life.
This set of high quality replacement steering stem bearings includes:
Complete chain and sprocket replacement packages.
High Quality chain. Will need to be cut to fit your sprocket combination.
Always carry a spare master link when out on the trail.
Master links are not interchangeable. Be sure to check the manufacturer and series on your chain.
These do not fit the TW200 or XT250. Only for 520 or 525 chains, Please verify chain size.
High quality steel front sprockets.
High quality steel rear sprockets from 39 to 53 teeth.
Sprocket color may differ depending on size.
A set of six high quality grade 10 sprocket bolts with lock nuts. Thread-lock compound has already been applied for extra security.
These bolts are flat head style, requiring a countersunk hole in the sprocket.
Shield your bike’s vital drivetrain components with B&B Off Road’s heavy-duty front sprocket case saver. This premium guard, CNC-machined from high-strength 6mm aluminum plate, offers unparalleled protection against rocks, impacts, and other off-road hazards.
Uncompromising Strength, Precision Fit:
Engineered for maximum durability, this case saver boasts a 6mm main body crafted from 5083 structural aluminum – a material renowned for its resilience. Complementing this robust core is a 4mm thick front sprocket cover, ensuring comprehensive protection for your drivetrain.
Designed for Flawless Performance:
CNC machining guarantees a precise fit for both Suzuki DRZ400 (2000+) and Kawasaki KLX400 (2000+) models. This ensures seamless integration with your bike, eliminating concerns about interference or compatibility issues.
Peace of Mind on Every Ride:
Whether you’re navigating technical single tracks or powering through dusty plains, this case saver offers the confidence to push your limits. By safeguarding your front sprocket and surrounding components, it minimizes the risk of costly repairs and keeps you on the trail.
This heavy duty DRZ400 chain guard is made of laser cut 1/8” aluminum and finished in textured black powder coating. The formed flange helps keep chain grime off the rear tire.
Mounting hardware included.
Aircraft aluminum withstands hard hits from logs and rocks. All mounting hardware and wear blocks included.
Replace your lower chain roller with this high quality roller with 2 sealed ball bearings. The stock roller has no bearings. It's just a plastic wheel riding on a bolt. Ball bearing chain rollers are smoother, quieter and last longer.
Designed for quick and accurate alignment, this tool clamps squarely to the rear sprocket so the alignment rod can indicate sprocket alignment with the chain.
Here is a tool to help you remove a few links from a chain that is too long. A great tool to have in your tool box.
The head of the pivot pin you are going to remove must be ground down level with the side plate before using this tool to push it out. Failure to do that will cause damage to the tool that is not covered by any warranty!
Can break or rivet chains from #35 to #530 like a pro.
kit includes a 2mm, 3mm, and a 4mm pin to fit most chains.
kit includes press plates,and all necessary riveting pieces and comes in a durable plastic case.
NOTE: when breaking a chain, YOU MUST grind the heads off of both pins on a link first.
Innovative design that cleans chain from 3 angles at once. Long handle keeps fingers and hands away from chain and sprockets.
Introducing Oinker®, the revolutionary chain lube attachment for dirt bikes, street bikes, and ATVs. Say goodbye to messy lubrication. Oinker® attaches to any chain lube or wax, ensuring a precise and even application to both sides of your chain. This means minimal overspray, keeping your swing arm, rear tire, and brakes clean.
*For cans with an attached smart straw, you will need to replace it with the included nozzle
What's Included:
Make your life a little easier by having a set of these in your toolbox. Designed to simplify installation and removal of clip-type master links. One tip is shorter and notched to be placed on the pin which allows the longer end to push the clip.
This Motion Pro press tool is a must have when installing and removing Clip-Style master links (520, 525 & 530 sizes).
Easily presses on and off master link plates, works on 520, 525 & 530 Clip-Style master links.
Maximum master link width 24.8mm.
Will not damage master links, hardened steel pins for reliable use.
Light weight billet aluminum construction.
A high quality master link press tool from Wirth Machine used for the removal and installation of master links using a press fit link plate.
Fits 520, 525, and 530 pitch chain.
ULTIMATE SPROCKET WRENCH KIT
SMX Carbon Look Rotor
This will give you a complete SET (Front and Rear) of brake pads.
Includes front and rear brake pads.
Galfer USA produces several different brake pad compounds for all types of riding styles and uses. With over 60 years of friction material production and research, they have learned that one compound doesn’t always do the trick across the board. If you are just looking for an OEM brake pad replacement or a high performance race brake pad, they have you covered!
Set includes front and rear brake pads.
Semi-Metallic Compound
OEM replacement upgrade. Great feel, long lasting, and very little rotor wear with this durable compound. Compound applications for almost every need, including off road, street, touring, enduro, dual sport and more. Precision made in our Galfer factory in Spain.
Our most popular compound! This compound is the work horse of the Galfer family and is a great OEM upgrade for the everyday rider.
Class 10.9 steel rotor bolts provide excellent sheer strength and include medium-strength threadlock patches to securely fasten your rotor.
Includes all the fasteners for both front and rear rotors.
Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
Each kit includes all necessary rubber components and brake pins.
Each kit includes all necessary rubber components and brake pins.
All the parts you need to freshen up your brake master cylinder. New piston, seals, return spring, boot and snap ring.
Made by Nissin, an OEM supplier in Japan
Replacement retaining pin for the brake caliper. Includes 1 stock style brake pin.
Be sure to use some anti-seize on the threads when you install it.
Front caliper only for DR350 and DR650
This anodized billet piece, brings a touch of color to your bike. Available in red or blue, it replaces the stamped steel clevis that connects your brake pedal to the master cylinder.
This brake bleeder makes bleeding your brakes a one man job.
The unique check valve allows fluid and air to escape while preventing air from re-entering the system.
Combines wrench and bleeder valve into one convenient and compact tool
DRZ400 E/S
A pair of Race Tech fork springs to dial in your front suspension to suit your weight.
Fits all DRZ400 models with conventional forks (not for SM)
Recommended spring rates:
| Rider Weight w/gear lbs. | Spring Rate |
|---|---|
| 90 or less | .42 |
| 90-119 | .44 (stock) |
| 120-150 | .46 |
| 150-180 | .48 |
| 180-220 | .50 |
| 220-250 | .52 |
| 250+ | .54 |
Low friction 'triple lip' seal design. Oil seals last 3-4 times longer that OEM seals. Kit includes Fork Seals and dust wipers.
An excellent replacement for the stock fork boots. These are great for protection from dirt, rocks and other contaminants. These boots utilize the latest advances in material technology to adapt to fork and styling demands. These high quality fork boots are 1/4 the price of the OEM factory replacements.
Helps protect vulnerable fork tube and seal from dust, dirt, and corrosive elements. Hook & loop (Velcro) fastening on back side makes installation or removal for cleaning a breeze.
Race Tech shock springs in a wide range of spring rates to dial in your rear suspension to suit your weight (stock spring is 5.3 kg/mm). Recommended spring rates:
| Rider Weight w/gear lbs. | Spring Rate |
|---|---|
| 100 or less | 4.6 |
| 100-124 | 4.8 |
| 125-149 | 5.0 |
| 150-174 | 5.2 |
| 175-199 | 5.4 |
| 200-224 | 5.7 |
| 225-274 | 6.0 |
| 275 + | 6.3 |
The Race Tech Gold Valve allows you to tune both compression and rebound valving for vastly improved performance.
Complete high quality kit to replace the bearing and seals in the DRZ400 shock linkage. Includes the lower shock bearing.
| Kit Contents: | |
|---|---|
| Seal | 8 |
| Needle Bearing Shaft | 4 |
| Needle Bearing | 7 |
For a top notch rebuild or re-valve of your rear shock use this high quality replacement seal head.
Heavy duty shock bumper. The stock bumper is prone to disintegrating with age. If you are re-valving your shock it's a good idea to be sure the bumper is in good shape.
Complete high quality kit to replace the bearing and seals in the DRZ400 swingarm pivot.
Billet aluminum lowering links. Lowers the rear suspension.
Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.
Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.
Lowers the rear suspension 0.75 inches. Precision machined from billet aluminum and gold anodized.
Based on the wildly popular Race Tech Suspension Seminars taught by Paul Thede around the world, this step-by-step guide shows riders how to make their bikes handle like the pros. Thede gives the lowdown on all types of suspension, including cartridge and non-cartridge forks as well as dual-chamber and nitrogen-charged shocks.
The three forces of suspension, testing procedures, even the black arts of chassis geometry: This explains it all. The book provides step-by-step photos of suspension disassembly and assembly as well as a detailed troubleshooting guide for dirt, street and track.
Innovative design makes tool easier and more secure to use than old fashioned pin-aligned drivers
Showa removed the schrader valve on many newer rear shocks. Now you need a needle to recharge your shock with nitrogen after a rebuild. Race Tech built this unit just for that job.
The features of this tool include 300 psi capacity, bleeder valve and T-handle plunger pin chuck. Swivel chuck has a 12" flexible hose. Comes complete with instructions, carrying box and Schrader valve extension (required on some Showa shocks). Nitrogen bottles available at any welding supply house.
Hard anodized oval shaped aluminum muffler with a TIG welded reinforced muffler bracket and red powder coated stainless steel end tip. Sleek muffler design gives you lots of clearance and it has a removable screen-type USFS approved spark arrestor. Head and mid-pipe are constructed from 304 stainless steel. Entire unit is pounds lighter than stock and gives great horsepower and torque gains throughout the RPM range.
All handmade in the USA with a 1 Year Limited Manufacturers Warranty.
The race-bred RS-2 exhaust has proven to be extremely popular among rider looks for a combination of performance and value. It enhances performance dramatically, provides an enviable exhaust note and offers the unmistakable look and sound of Yoshimura. RS-2 mufflers feature a straight baffle that leads to a single turn-down machined aluminum end cap.
All models have a USFS Approved spark arrester in a oval-shaped sleeve with a large volume of packing material.
The RS-4 Twin Pipe kit was previously only available as a custom system for Kevin Schwantz.
Yoshimura is offering these incredible "Twice Pipes" which are completely fabricated by hand and TIG welded to perfection. They certainly sit at the high end of what is available for the mighty SM... The pipes have a stainless steel header and "Y" pipe mated to twin carbon fiber or aluminum RS-4 mufflers for incredible looks and performance. The kit also comes with a custom Yoshimura side stand.
Hard anodized oval shaped aluminum muffler with a TIG welded reinforced muffler bracket and red powder coated stainless steel end tip. Sleek muffler design gives you lots of clearance and it has a removable screen-type USFS approved spark arrestor. Unit is pounds lighter than stock and gives gains in horsepower and torque throughout the RPM range. All of that in a package handmade in the USA with a 1 Year Limited Manufacturers Warranty.
The V2 Series Slip-On muffler features an aluminum body, TIG welded components, stainless steel inlet tube and a great new look. This Lightweight Slip-On weighs approximately 5.5 lbs.
The DG Performance systems offer increased throttle response, power and torque. Standard sound level is approximately 98 db. Equipped with a US Forestry approved spark arrestor.
The Powercore 4 spark arrestor muffler. FMF developed the Powercore 4 to increase the horsepower and torque throughout the entire power curve. Highest quality packing for long life. Removable spark arrestor included. Louder than the Q4. Approximately 99db stock or about 94db with optional Quiet Insert installed.
The Q4 employs intricate chambers, baffles and proprietary multistage packing material making it the best performing quiet muffler available.
Constructed from aircraft grade aluminum and high strength stainless steel.
Sound output 96dB. Several pounds lighter than the stock muffler.
No repacking required! The Leo Vince X3 Enduro is made with TIG welded stainless steel internals and aluminum outer shell. It features a semi-direct chamber design that is maintenance free. It's quiet too! Our own in-house testing showed a 84dB sound level using the USFS J1287 testing procedure. 84dB is louder than stock but significantly quieter than any other aftermarket muffler. It includes a certified Spark-Arrestor.
This muffler works on OEM header only!
Yoshimura RS-3 that will slip right on to your stock header. Made by hand to the highest quality standards using the championship-winning racetrack experience and their extensive R&D facility ensure these pipes perform and will last.
Both full systems and slip-on mufflers include 96 dB sound insert/USFS approved spark arrestor installed in the muffler. Mid-pipe is stainless steel while the stainless RS-3 oval muffler design has a slim profile with an aluminum end cap.
Works on OEM header only!
Constructed from 304 stainless steel and breathes much better than the stock unit. Handmade in the USA with a 1 Year Limited Manufacturers Warranty.
The PowerBomb header promotes better flow by allowing a small expansion of the exhaust gasses. The 'bomb' also acts as a pre-muffler taking the edge off of overall sound levels.
