We are now accepting submissions for this year’s Calendar Photo Contest! Please upload your images here by 9am Pacific on September 16, 2025.
If you're like us, you hate the long floppy vent hose hanging off the cap of your aftermarket tank.
This one-way vent cap replaces the long hose with a short one only about 2" long. It allows air into your tank but prevents fuel from sloshing out.
Machined from billet alloy and anodized for good looks.
Not for stock fuel tanks!
Get better range from your XR650L by adding a Clarke 4.7 gallon fuel tank. Cannot use stock shrouds.
Available in Natural, White, Black, and Red. Natural color is recommended if you wish to easily see the fuel level in the tank. Includes cap, uses stock petcock.
You want a lighter replacement for your heavy steel stock tank? Don't need the extended range (or bulk) of a big tank? The 3.7 gallon tank from Clarke might be just right. It's almost 5 lbs lighter and holds close to 1/2 gallon more fuel than stock to increase your range by about 20 miles. Fits with your stock petcock, Pingel or Raptor petcock.
Acerbis fuel tanks were designed to provide additional fuel capacity without sacrificing ergonomics, and are the perfect choice for the rider trying to increase the range of their machine. Constructed of impact and abrasion resistant Polyurethane, Acerbis fuel tanks are durable, stylish, and will provide years of service.
* Will not fit 2017 Model
Designed to enhance the appearance of your motorcycle, yet provide greater riding distance per tankful. Larger capacity than stock, yet very slim and sleek. Perfect for wherever your adventure takes you! This tank is made from POLYETHYLENE CROSSLINK for extra strength and durability.
Fits EFI Models Only
Does Not Fit New KLX300 "R" Model
All of these lines are stronger and more durable than vinyl fuel lines and are resistant to swelling, UV light, as well as hardening and cracking.
Five-layer Greenshield® Barrier Technology cuts vapor loss and saves fuel, making it safe for the environment and fuel efficient.
1. Barrier tube - provides high heat and corrosive liquid resistance.
2. Greenshield® barrier - patent-pending technology provides the lowest permeation in the industry.
3. Adhesion layer - secondary protective barrier.
4. Reinforcement layer - spiral textile reinforcement provide strength and pressure resistance.
5. Cover - protect underlying components.
Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a plusher ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.
Complete seats are built by Seat Concepts on a new seat pan and come ready to be installed on your bike.
| Width: | 10" (254mm) |
| Height: | Same as OEM |
Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula is plush, while still offering the necessary amount of support. Their unique comfort and shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.
These great features combine to offer you a custom seat feel, and provide greater enjoyment and increased range for long commutes, or Dual-Sport rides!
The Complete Seats come assembled with an high quality aftermarket pan and ready to ride.
Fits Model/Years:
2022-24 KLR650, S, ABS, TRAVELER, ADVENTURE
| Width: | 12 3/4" (324mm) |
| Height: | Same as OEM *2023 KLR650S (1.25"/ 32mm Taller than stock) |
Seat Concepts seats are constructed using a foam material that is higher quality than OEM seat foam. Their proprietary formula is plush, while still offering the necessary amount of support. Their unique comfort and shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.
These great features combine to offer you a custom seat feel, and provide greater enjoyment and increased rangefor long commutes, or Dual-Sport rides!
The Complete Seats come assembled with an high quality aftermarket pan and ready to ride.
| Width: | 12 3/8" (314mm) |
| Height: | Same as OEM |
The ProCycle seat was designed for both comfort and function. Our seat is built with an advanced Progressive Density Foam (Pd-F) for those long days in the saddle, and also giving you freedom to move while standing.
The wide and sturdy seat makes long rides more comfortable. The vinyl weave helps keep you cool by letting air flow between you and the seat. The front of the seat is narrower, giving you space for your knees when you're standing, while the sides have grip so you can hold on with your knees while riding.
We will build the seat for you in-house on a new seat pan so all you have to do is put it on and go ride. Choose the heated seat option and we will add a Seat Warmer during the build process.
| Width: | 11" (279mm) |
| Height: | Same as OEM |
These wider seats from Seat Concepts help keep you comfortable on those long commutes or dual sport rides. The added width and improved foam density help keep your seat from being the item to stop you from going on those big rides or enjoying the bike.
The Complete Seats come fully assembled on an aftermarket seat pan, and are ready to install and ride.
| Width: | 9.5" (241mm) |
| Height: | Same as OEM |
Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a plusher ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.
These great features combine to offer you a custom seat feel, and provide greater enjoyment and increased range for long commutes, or Dual-Sport rides!
The Complete Seats come assembled with an aftermarket pan and ready to ride.
The Commuter shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but is much more dished out towards the mid-point to distribute rider weight over a greater area. The passenger platform has been built up to help prevent the passenger from sliding into the rider.
The Commuter seat is the best choice for extended pavement riding and mellow offroad. The unique shape and added width will provide greater enjoyment and increased range on a long commute, or Dual-Sport ride!
| Width: | 13" (330mm) |
| Height: | Same as OEM |
The ProCycle seat was designed for both comfort and function. Our seat is built with a premium grade foam that is denser for those long days in the saddle, and also giving you freedom to move while standing.
The wide and sturdy seat makes long rides more comfortable. The vinyl weave helps keep you cool by letting air flow between you and the seat. The front of the seat is narrower, giving you space for your knees when you're standing, while the sides have grip so you can hold on with your knees while riding. If you choose the gel cushion option, it helps improve blood flow, prevents pressure points, and makes it easier to ride for longer without getting tired.
Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!
Available as a Foam and Cover Kit for OEM pan. This kit DOES NOT include the pan.
| Width: | 11" (279mm) |
| Height: | Same as OEM |
Low friction 'triple lip' seal design. Oil seals last 3-4 times longer that OEM seals. Kit includes 2 Fork Seals and 2 Dust Wipers.
Included in this kit are fork springs, Cogent DDC (Drop in Damper Cartridge) performance cartridges and one bottle of 5w fork oil. Refresh those tired old forks and make them better than new. These DDCs from Cogent are easy to install. No taking the forks apart, no drilling of the damping rods, nothing. Just take them off, flip them over to drain the oil, add new 5w oil, drop in the DDCs and then add the springs.
This upgrade offers better control off-road as well as on. Less brake dive keeps the fork up in the middle of the stroke on-road and better control off-road whether it be rolling water bars or bouncing off the rocks.
Stock Spring Rate is .50 kg/mm. The .60 kg/mm springs are 20% stiffer than stock while the .70 kg/mm is 40% stiffer than stock.
DDC Tool will not work with this spring series
A CNC machined fork brace to stiffen up the notoriously wimpy front end on the DR. Have more confidence in your front end on or off the pavement.
Split design means that installation takes minutes without having to remove the forks. Available in a black anodized finish.
You can adjust the preload on your rear shock quite easily, why not on the forks as well? These caps give you the ability to adjust the spring preload in your forks to match your load.
Caps are CNC machined beauties with a center blue anodized core.
Custom developed by BBR Motorsports for the ultimate upgrade for mini four-strokes. Sized perfectly for fast/aggressive adult mini riders. This is the most important upgrade you can make for an adult sized rider. The stock suspension is too soft for most adults.
These springs are custom wound specifically for the Kawasaki KLX's. Stiffer than the stock springs, these will make your front perform significantly better.
These Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. These units have been given the seal of approval by the ProCycle staff for both performance and ease of installation. No disassembly of your forks, no drilling of damper rods. Just change the oil over to 5w and install the DDCs under the springs and hit the trails.
DDC Tool will not work with this spring series
Cogent Dynamics Mojave product is a drop-in replacement for the DR650 stock shock, no modifications necessary. Mojave is not simply an improved Suzuki shock, it is a brand new replacement shock that is a totally engineered suspension solution to suit your needs.
Each shock is assembled and tested on the Cogent Dynamics suspension dyno before being packed up and shipped. Like its bigger brother the Mojave Pro Series, this will make an incredible difference in the handling of your DR.
Mojave Improvements over stock:
Mojave upper mount: uses a precision spherical bearing with dust seals, which accurately transfers damping forces to the motorcycle frame.
Internal improvements: Cogent designed shaft, seal head, damper piston, adjuster and clevis.
Mono tube construction: precision honed, super-stiff steel body with an upper body cap machined from billet aluminum.
Built-in billet aluminum separator piston provides an in-line gas pressure reservoir which eliminates the Suzuki rubber bladder.
This shock package includes the CNC machined Bling Ring Preload Adjuster Collar and Preload Bearing that will make preload adjustments easy.
Select the spring you want installed based on the load you plan to carry. For riders (and gear) less than 250 pounds we recommend the 7.6 kg/mm spring. If you regularly have more than 250 pounds the bike, you might want to use the 8.15 kg/mm spring. If you have any questions at all about this, please call.
You may choose to add the Hydraulic Preload Adjuster to make it the easiest of all. All you do is twist the knob. Includes mounting bracket for knob unit. (Some CA carb compliant models may need slight modification for mounting the preload adjuster.)
Low shock also available. This option will lower your seat height 1" without the need for lowering links. All other features of this shock are the same as the stock height.
Sized perfectly for adult back-yard racing or fast/aggressive mini riders. This is the most important upgrade you can make for an adult sized rider. The stock suspension is too soft for most adults and aggressive kids. Fits stock shock.
Aluminum alloy lowering link. Lowers the rear suspension approximately 1 inch.
Bearings included.
Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.
An excellent replacement for the stock fork boots. These are great for protection from dirt, rocks and other contaminants. These boots utilize the latest advances in material technology to adapt to fork and styling demands. These high quality fork boots are 1/4 the price of the OEM factory replacements.
| Top Diameter | Bottom Diameter | Length |
| 42 mm | 45 mm | 12in |
Transform your ride. Get that pressure off of your face and chest! MadStad's quick-release mounting system gives you touring comfort on your naked bike. Adjust the height and angle of our windshield to dial in smooth airflow and a more comfortable ride while still looking over the shield. You can switch back to naked bike in seconds, without tools, however you will be so much more comfortable you may not want to!
What's included in the kit:
Their complete drop-in quick-release system is custom-made for the SV650 and includes everything needed to mount and position the shield. Your bike will not require any modification. Here are the system components:
The quick-release base brackets mount to your forks. The adjustable shield brackets lock onto the base and with the shield system attached you can adjust it for the optimum height, angle and airflow to dial in the comfort for your particular height and riding position. They included a long 7/8" crossbar both for stability and so you can mount your smartphone or GPS unit up higher front-and-center where you can more easily see it.
If you want to go back to stock naked bike configuration simply release the locking plungers and slide the system off. Keep in mind that the crossbar, and anything you may have mounted to it, will also come off with the system.
Transform your ride. MadStad's patented mounting system allows riders to adjust the height and angle of their motorcycle windshield resulting in much smoother airflow, better wind protection and a more comfortable ride than any fixed windshield can provide. Better still, this dual-sport version pivots the shield down and forward to get it out of your way for off-road riding!
What's included in the kit:
Their complete bolt-on system is custom-made for your bike and includes everything needed to mount and position the shield. Your bike will not require any modification.
The MadStad brackets bolt to the top of your fork clamps and are completely free of the handlebars. You can adjust the shield for the optimum height, angle and airflow for comfortable street and highway riding. When going off-road you can leave your comfort adjustment as-is and pivot the entire system down and forward in front of the headlight so you can get it out of your face completely. When it comes time to hit the pavement again, simply pivot it back up and you are back in street riding comfort mode.
New replacement side panels specifically made for gen 1 KLR650.
Available in 4 colors.
Will not fit KLR250
Depending on your application and preferences, more than one optional heat shield may be useful.
This kit is for those of you looking for a bit more arm room and a better platform for your feet in the TW cockpit. Included are ProCycle Wide Foot Pegs and our oversize bars with 30mm risers.
Kit does not include new throttle tube. If you have 2001 or newer TW200 and would like a new billet aluminum throttle tube, please select the add-on box to receive one with your order.
2 high-quality bushings per set. They recommend changing bushings every 40 hours or at least once a year to get the best performance out of a set. If you are on an Adventure Bike and are doing a lot of road miles they recommend swapping out bushings once a year to ensure that you get the most vibration dampening of the bushings.
Every new set of pegs comes with a 90A bushing installed. This is a medium flex rating.
80A is the softest and 95A lock-out is the stiffest and has the least amount of flex.
The bushings act like the suspension on your bike. With bushings, there are a couple of things to think about. The more firm the bushing the more durable and longer it will last. They use a durometer, a hardness scale 0 being the softest and 100 being the hardest. They don't go below a80 because they found that durability isn't great below this but have tested as low as a60 bushings. A bigger person that rides enduro-style terrain might want an a96 or a98 rated bushing. A lighter person might want the opposite but in the end, it comes down to personal preference.
The bushings are high quality yet inexpensive (they achieve this because they use skateboard bushings that are already developed and produced in massive quantities around the world) and a wear item designed to be replaced each season or depending on how hard or often someone rides.
For use on Motion Factory Foot Pegs Only
Our complete foot peg assemblies. 1-3/4" lower than stock. No extra brackets that hang down below the frame. Easier on the knees. Wider platform Yamaha YZ style footpegs are stronger and give you firmer footing. Mount solid to the frame. No more 'droopy' feeling when standing on the stock pegs. Lowering your footpegs makes it easier to stand and less of a reach down to the bars when standing.
Now you can get our Low Pegs with MK4 Pivot Pegz or black Fastway ADV pegs (both Yamaha YZ pegs) installed!
Revolutionize your riding experience with Swiftkicker.
An adjustable kickstand for your motorcycle. Swiftkicker is built for offroad motorcycles, dual sports, and dirt bikes. Designed with the idea in mind that motorcycles should be able to take you anywhere, the Swiftkicker motorcycle kickstands help you do just that. You can set the length to anywhere in a six inch range of travel so you can stop anywhere without having to worry about having an even surface to park.
With just a flick of your toe, you can adjust the kickstand to the desired height, park your motorcycle, and be on your way.
No longer will you have to search for a rock or piece of wood to prop your motorcycle up with, or even worse, coming back to your bike to find it has tipped over from unstable ground.
The Swiftkicker is 100% manufactured in the USA from the highest quality components.
The billet 6061 head and the hard anodized tube are significantly stronger than the stock stand. An oversized foot will assure that the end of your stand stays where it belongs, rather than eight inches underground with your bike lying on top of it. The design is trail proven in the harshest possible conditions. Because nothing is indestructible, any of the kickstand components are replaceable at a lower cost than purchasing an OEM kickstand.
Measured from the center of the pivot to the bottom of the foot.
Adjustable lowered kickstand that can be extended, set at stock length, and shortened. A must have for lowered bikes.
Here is an adjustable height centerstand from T-Rex Racing. If you are running supermoto wheels or lowering links, this centerstand will be much easier to use.
T-Rex stands are made from steel tubing finished in black powder coating for durability. Back by a 3-Year limited warranty for any material or manufacturing defects. Rest assured that you are getting best material commercially available.
Greatly eases basic chain maintenance, tire changes, parking, cleaning, etc. All necessary hardware is included. Installs using basic hand tools.
The Apollo Heated Grips are designed with an integrated adjustable thumb switch, which allows them to easily fit on any kind of motorcycles on the market. The integrated thumb switch gives control to the rider to adjust the temperature level while keeping hands on the bar for a safer ride.
Its wide temperature setting range will keep the rider comfortable under the cold riding conditions.
The 5 color LED display will enhance the visual look of the heated grips and will allow the rider to quickly know at which heat level the grips are set.
This system will also detect if the battery voltage is too low and will automatically shut down the heated grips in order to make sure the rider have enough power to start the engine or use the motorcycle.
Specifications:
Billet levers that are short enough to provide clearance for your hand guards. Warp 9 Flex Brake Levers are machined billet, anodized and hinged with a CNC machined master cylinder interface. Adjustable reach allows customization to the rider's hand size. Double hinge design allows lever to flex out of the way in most impact situations. These high quality levers are approximately 1/2" shorter than stock. Brake lever includes a nice billet clamp with nylon sleeve to allow the assembly to rotate on impact. These levers work with the stock brake light and clutch safety switches. Will not fit with the stock OEM wind deflectors.
Will not engage the clutch switch on 2010 and later models
In stock with limited availability in Clutch Lever only, discontinued item. "3-Finger" levers still available.
Quality replacement levers. Standard length.
Quality replacement levers. Standard length.
Original Suzuki factory replacement levers for your DRZ400S/SM/E
Genuine OEM replacement choke cable.
New from Warp 9, a full floating 320mm Supermoto disc with caliper relocation bracket! These rotors have an additional hole for placement of a magnet for an electronic type speedo like the Vapor.
Includes a fresh set of brake rotor bolts.
New from Warp 9, a full floating stock size rotor. These rotors have an additional hole for placement of a magnet for an electronic type speedo like the Vapor.
Includes a fresh set of brake rotor bolts.
GBrakes Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
Now you can have minimum output shaft wear, minimum chain drive wear with the FRITZCO DRIVELINE sprocket. The design of their sprockets provide correct chain alignment, allows for full spline contact with the XR650L's output shaft, fit the counter shaft either way, and straight up no hassle installation with the OEM two bolt retainer and fasteners (except 13 tooth that comes with it's own quick change retainer). Their sprockets are machined from alloy steel that is comparable in every way to OEM Honda and the best offered by other manufactures. The sprockets are then given a heat treatment that provides a compatible sprocket for the Honda output shaft and longest wear life possible.
A way to double the sprockets life would be to have a sprocket that fits on the shaft either way so both sides of the teeth can be used. Bear in mind you can't wear one side of the teeth all the way through, then flip the sprocket, and expect double life. You must reverse when a normal wear pattern develops.
16 tooth sprocket is the biggest front sprocket that will run with the standard 110 link chain and 45 tooth rear sprocket on an XR650L
The OEM cover will require modifying to use the 16 tooth sprocket on your XR650L.
These quality JT sprockets are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.
For reference, the stock gearing for the WR250R is 13/43 while the X model runs with a 13/42 stock configuration because of the SM wheels/tires. Both use a 108 link chain with the stock gearing.
The JT rear sprockets listed are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.
Limited availability on Aluminum from PBI. Manufactured from aircraft 7075 T651 Plate Aluminum.
If you want the additional low-end grunt that the 46, 48 or 50 tooth rear sprocket will give you, you will need longer chain as well.
New Rear Sprockets require new Sprocket Bolts because of a difference in the holes vs. the stock bolts.
High quality steel front sprockets from 12T to 14.
Color may vary based on manufacturer availability, quality will not be compromised.
Individual 14T, 15T or 16T front sprockets.
JT Sprockets are made from the latest generation of computer design and control metal cutting equipment for maximum durability. Front sprockets are made from chromoly SCM420 steel alloy. All sprockets are heat-treated and hand-finished to meet or exceed the highest possible quality standards.
Quality steel sprockets and EK SRO6 O-ring chain. We put them together to make a complete, affordable kit. Chain comes with clip type master link.
Provide protection for your motorcycle’s front brake and clutch levers with Barkbusters aluminum bar lever protection handguards. Designed specifically for the Tenere 700, these guards feature heat treated full wrap aluminum backbones that mount at two points on each side for strength. Prevent costly damage to your motorcycle with Barkbusters aluminum bar lever protection handguards.
Features:
Add Plastic Handguards for a complete kit.
To fit tapered 28.5mm (1 1/8") handlebar.
NOTE: will not fit Renthal Twin Wall or Barkbusters VSBar.
Bolt-on side case armor from Warp 9 Racing.
Made of High Density Polyethylene, the same very tough stuff they make their frame and axle sliders out of.
3mm thick complete side case coverage
6.5mm thick in the leading and bottom edges where impacts typically happen
Covers the oil filter which takes a lot of impacts on these bikes
Includes new longer case bolts to hold on the case guards
Yes, plastic! This is a product from our friends at Acerbis. Ultra tough injection molded reinforced composite. Flexible Heavy-Duty Polypropylene will not effect chassis ability to flex, will not effect handling
It's twice as thick as a metal skid plate but is only half the weight. Plastic glides over rocks and roots better than aluminum. It also reflects less engine noise, bike will run quieter and cooler compared to alloy skid plate. Full coverage, mounts to existing threaded holes at the rear of the frame.
Motocross brake rotor featuring ultra lightweight radically profiled contours for great looks, great self cleaning and brake performance. Made with tough and durable heat treated stainless steel. Heat treated to perfection and then diamond ground to micron accurate surface finish and parallelism and will deliver great brakes that perform well and last.
The RS-2 is a potent and versatile design that evolved from their original TRC, engineered to provide increased power delivery. With a different pyramidal shape that features increased volume, the RS-2 is a quieter system with a larger core — and it offers the added bonus of outstanding performance in a value-priced package.
We recommend Anti-Seize on exhaust fasteners
X3 EVO represents the off-road evolution: LeoVince has combined all its experience in the off-road world with cutting-edge materials and Italian design, enhancing freedom in its purest form.
The X3 EVO body is made of AISI 304 stainless steel with TIG welds handcrafted by specialized operators, to guarantee long-lasting performance. X3 EVO will allow you to face the most extreme environments and conditions because it does not fear water or mud, nor wear over time.
The LV logo is their tribute to a motorcycle culture that we have loved for 70 years and is laser etched on the body of the exhaust: it is as endless as their passion.
They manufacture the end cap in 100% real carbon, with their special 2x2 twill carbon fiber, specifically designed to resist high temperatures and make the X3 EVO even lighter.
The matte clear coating, in addition to enhancing the carbon texture, protects the end cap from wear and UV rays, keeping the X3 EVO always in a perfect shape.
The sound of X3 EVO is already unmistakable at low revs. X3 EVO has a direct interior, specially conceived to channel the exhaust gas in an optimal way, to unleash a deep sound, giving a new voice to your bike.
The X3 EVO's Spark arrester has been tested and approved by the United States Forest Service and is essential for off-road riding in compliance with regulations, with more peace of mind, more respect for the environment and more fun.
The DG RST (Reduced Sound Technology) muffler is the quietest DG muffler and is designed especially for dual-sport machines (Just 89db @ 3200 RPM). A new baffle design dissipates sound waves reducing noise output in a very efficient manner. This new design also stretches out the time between muffler repacks. Included is a Stainless Steel mid-pipe, USFS Approved Spark Arrestor and a new Aluminum end cap.
You may want to consider a new exhaust gasket that goes between the header and the muffler.
Bradley performance bomb header for TW200.
By positioning this “Bomb” at a key point in the system, increased performance and flow is achieved through the expansion and contraction of exhaust sonics through the system. The result is a flow increase of nearly 10%.
The outer chamber in the Powerbomb allows the air to expand, cool and ramp back up at a higher velocity.
Fits all years of TW200 and works with all other brands of mufflers. Stainless steel and nickel plated. A clamp-on shield can be added, sold separately.
Helix brand exhaust springs made from zinc plated music wire. These are the springs we use on our GSXR Mid-Pipe Kit. If you lose one, or break one, these are the direct replacements. Sold as a Pair.
CycleRacks are made out of steel tubing, bent in a press, and welded together in a jig. All of their racks have the same platform, 18" wide by 12" deep. Includes lower mount hardware.
All of their products are 100% made in the USA. If the rack is ever broken for any reason, CycleRacks will replace it for free, you just pay the shipping.
ProCycle side panel guards to keep your saddlebags from fouling the side covers. Constructed from mild steel tubing that is powder coated black for nice long lasting good looks.
Add your favorite set of saddlebags for a very economical luggage solution.
Guards only, saddlebags sold separate.
Simple, lightweight rack made from rugged 1/8" 5052 Aluminum, with a rigid 5-point mounting system.
Low profile allows for easy seat removal.
Features:
Note: Placement of this top rack does require removal of the stock tool bag.
E3 Resistor Spark Plugs
The unique design of the electrode maximizes the power generated by the spark plug through Diamond Fire technology. This electrode combines advanced performance capabilities and innovative technology to enhance the shape of the flame kernel. Consequently, the flame front ignites the air/fuel mixture more rapidly, accelerates heat transfer into the combustion chamber, and creates a more concentrated pressure front, facilitating a quicker pressure rise during the cylinder power stroke. The outcome is a more efficient combustion process and improved engine performance, making this a truly premium spark plug.
Keep your motor running right with fresh spark plugs!
NGK is one of the world's largest manufacturer of spark plugs, whose products are used as original equipment (OE) on countless motorcycle and automobile models.
GoldPlug is the gold standard in engine protection.
Stainless steel drain plug with an extremely strong magnet that picks up metal flakes in your oil.
10MM Thread for frame drain.
Wiseco 96mm/+1.00 mm piston with rings, wrist pin, circlips, head gasket, and base gasket.
Requires your cylinder to be bored to fit the larger piston.
All Wiseco Pistons are forged from high silicon, low expansion aluminum which offers superior strength, reduced weight, improved heat transfer, and longer life.
Diamond turned finish from one of the many CNC computer controlled turning centers guarantees you a perfect finish with no size variation. Wiseco pistons can be installed in any of today’s cylinder bore compositions
Wiseco’s state-of-the-art computerized manufacturing facility is dedicated to supplying both the high-perfomance racer and recreational enthusiast with the finest forged piston available in today’s market place.
Twin Air Filter's patented design, high quality materials and superior construction deliver unbeatable performance and protection - and make Twin Air Filters the hands-down choice of more World and National Champions than all other filters combined.
An air filter is your engine's only protection against the elements, and your stock filter isn't up to the task. Replace it with a Twin Air- the number 1 filter system proven on motocross tracks around the world.
Twin Air's fused layers of open-pore foam and fine inner foam trap even the smallest particles-without restricting airflow
Our own jet kit for the DR650 stock Mikuni BST40 carburetor. Includes the extended fuel mixture screw and stainless steel Allen screws for the float bowl and top cap. Also included are new Viton o-rings for the float. Comes with easy to understand detailed instructions and diagrams. Includes a template for modifying the air box.
This kit includes 2 Needles that have been developed by JD Jetting and manufactured for them to their exacting specifications. These two needles allow a wide range of tuning possibilities and provide correct fuel delivery at any throttle position.
4 allen type screws for the float bowl are also enclosed should you strip out the stock screws during your tuning process. Complete instructions with photos, jetting suggestions for different set-ups and situations, 5 Main Jets and a drill bit complete the package.
This kit is for the 36mm Mikuni CV carburetor and includes 2 Needles that have been developed by JD Jetting and manufactured for them to their exacting specifications. These two needles allow a wide range of tuning possibilities and provide correct fuel delivery at any throttle position.
4 allen type screws for the top of the carburetor are also enclosed should you strip out the stock screws during your tuning process. Complete instructions with photos, jetting suggestions for different set-ups and situations, 5 Main Jets, a Pilot Jet and a drill bit complete the package.
Dyno and field tested, the Power Surge 6X will allow correction for humidity, temperature, air pressure, along with race fuels and motor modifications. The tuner adjusts in a matter of seconds in 6 zones, including an accelerator pump feature for more throttle snap response. The tuner can add or subtract fuel from the injection system. Conditions like rich or lean running, and stalling from flame-out at low revs can be corrected.
A premium billet sprocket carrier from Warp 9 Racing that houses 2 bearings to help protect against the sideways twisting load that is commonly known to prematurely wear out the bearing and cush rubbers. This wear can cause extreme failure possibly damaging the hub.
Anodized, Includes spacers already installed.
Stock sprocket bolt pattern to fit any stock compatible sprocket.
These are designed to work with Warp 9 and OEM hubs.
Replacement brush plate kit fits both original stock or aftermarket starter motor.
Modern technology for the DR650s charging system. Mosfet style regulators produce less heat, are more efficient and last longer than old tech 'shunt style' regulators. Regulator is made by Rick's Motorsports, and includes a ProCycle adaptor bracket to fit into the existing space on the bike.
This regulator / rectifier is Lithium compatible.
Heavy Duty replacement Voltage Regulator. More robust, but lower cost than the factory unit.
New Hot Shot Suzuki Stator: aftermarket stator is made with heavy duty components and is a direct replacement for OE# 32101-32E01 or 32101-32E00.
This stator will provide your bike with 20% more power (240W) to support your added gear. Whether you have heated grips or you're running multiple aux lights, this unit will give you the power that you're looking for.
This high output stator will allow you to run brighter lights, heated gear, heated grips, etc. From ElectroSport
Performance CDI for the Yamaha TTR125 increases the rev limit by 1,000 RPM over the stock rev limit. Easier starting, crisper throttle response.
This CDI box is a direct plug in replacement CDI. Simply locate and remove the stock CDI, and plug the new unit directly into the wiring harness, no modification needed. Suitable for stock and modified machines.
The Shorai LFM Standard Recommendation is the best overall pick for most applications, and has been selected to give strong cranking performance and long lifespan.
Measures 4.45" x 3.5" x 2.28"
Weight (lbs): 1.52 lbs
Weight (kg): 0.69 kg
Cold Cranking Amps: 210
Polarity: [+ -]
Each Shorai battery includes self-adhesive foam panels to achieve a snug fit in your battery box.
Shorai batteries deliver more energy faster, with less weight and with less wear on the battery per start cycle than any other brand or technology available on the market today.
Weight (lbs): 2.45 lbs
Weight (kg): 1.11 kg
Cold Cranking Amps: 285
Polarity: [+ -]
Dimensions: 5.8"x 3.4" x 3.5"
Self-adhesive foam shims are included and insure a great fit to the battery box, as well as extra vibrational an thermal insulation.
The Bridgestone AdventureCross AX41 Tires features a distinct pattern design, compound and high cross sectional area to provide enhanced performance on or off-road.
This 30% street/ 70% off-road adventure tire that complements the modern dual sport motorcycles.
These are all tubeless tires that are also OK to use with a tube on spoke wheels.
Motoz Tractionator Desert H/T series of tires are renowned for great traction and long wear life. These tires are designed to handle hard terrain, fast and rocky trails as well as gravel roads and desert hard pack. Tricky off-cambers, ruts and hard braking at extreme lean angles are no problem for this DOT approved tire.
Note: Tubes can be run in Tubeless tires, but a Tube Type tire cannot be run Tubeless.
Replacement Inner Tubes for your VanVan or TW200. Always a great idea to carry a spare on your adventures as the rear tube is often hard to find.
Features:
FunnelWeb ProLine Filter Highlights:
Like all FunnelWeb filters, the ProLine Filter features profile cut, single layer, single density foam that doubles the external surface area of the filter without increasing the original filter size. The ProLine Filter traps dirt, dust, sand and mud over a larger area on its outer surface, ensuring optimal air flow is maintained for maximized engine performance and reliability.
The single layer, single density polyurethane foam has the added advantage of being easy to clean and the ability to maintain its original shape after numerous washes. Overall, compared with conventional foam filters, FunnelWeb offers more protection from dirt ingestion, has longer service intervals and maintains high airflow rates when dirty.
This filter replaces the stock air filter, fitting inside the air box.
Special tool to remove the flywheel/rotor from the end of the crankshaft. You have to remove the flywheel/rotor to upgrade the doohickey.
For adjusting valve clearance on twin cam models. Holds valve spring collar down so adjusting pads can be removed. From Motion Pro, made from hardened alloy steel.
A compact and lightweight solution to eliminate the SNAP for a safer tow. If you have ever towed a motorcycle you are familiar with the snap that comes with a traditional tow strap. GCAG made the Dynatow with a section that gives 32 inches of stretch so both riders have an easier tow.
The 26 foot total length gives you enough room to maneuver around obstacles and allows the freedom to choose better lines if you are towing in the gnar.
You can also use this as a recovery strap. You can girth hitch the loop end to the bike and throw the other end to a friend to pull. The dynamic properties of the Dynatow will help assist the pull. All of this functionality fits in a flat pouch about the size of sandwich and only weighs 12.8 oz. Throw it in your bag and be prepared.
Specifications:
Please consider the following before use: Practice before you need to use this product. Always inspect your Dynatow strap before use and NEVER use a worn strap. They recommend a proper training class to learn safe methods for towing a motorcycle.
License plate bolt with bright white LED light. The simple way to light up your plate.
Designed to enhance the appearance of your TW200, yet provide greater riding distance per tankful. This larger fuel tank has double the capacity of the stock tank at 3.6 Gallons, yet very slim and sleek. This tank has a custom design that will allow the use of OEM & Maier side covers. These tanks are made with POLYETHYLENE CROSSLINK for extra strength and durability.
Comes with New Screw Cap.
Requires OEM/Stock petcock and oval rubber grommets for install.
If you do not have the grommets or if your O.E. grommets are in poor condition you can add these to your tank order.
Folding tip, forged aluminum shift lever from BBR Motorsports. Stronger and lighter than the stock shift lever, with a beautiful anodized (titanium color) finish.
Stock Suzuki choke knob holder guide. Replace your cracked or cross threaded stock unit with a new one.
Renthal chain lube is 100% lubricant, zero propellant. So this new 250ml bottle size combines high performance and value.
The all-new formula Chain Lube is specially designed to penetrate all parts of the chain. This all-condition lube is compatible with all o-ring and non o-ring chains.
Warp 9’s Pro Rim Locks are developed with Ice Track, Dirt Track and Flat Track Racers in mind!
Burnt Titanium Main Bolt
Lightweight Forged Aluminum Body
Black 7075 T6 Tower Nut and Base Washer
Base washer is machined to match each specific rim curvature for a perfect fit
About half the weight of OEM rim locks!
1.60 front – 1.8 oz
1.85 front – 2.0 oz
2.15 rear – 2.3 oz
2.50 rear – 2.7 0z
3.00 rear – 3.10 oz
ULTIMATE SPROCKET WRENCH KIT
