Spring time is in full swing here at ProCycle. With these busy days please be sure to let us know if your order is time sensitive. We try to do as much as we can to accommodate your upcoming trip.
Allows your bike to breathe much better giving you better response and performance.
Breather Filter
ProCycle Jet Kit which includes jets, needle, extended fuel screw, drill bits and Allen bolts to replace phillips (JIS) head bowl screws and detailed installation instructions
Choose Twin Air, DT1, or K&N filter with ProCycle filter wrap
OPTION - Twin Air breather filter (replaces standard breather filter)
DP brakes are available in two different compounds for the DR. The standard Sintered metal material pads provide powerful braking with industry-high HH+ friction rating that is equally adept in wet or dry conditions. They have a quick break-in period and excellent initial response. An oxide-based ceramic material on the rear of the backing plate keeps heat away from the caliper piston and fluid in extreme conditions giving a fade-free performance in even the harshest conditions.
The material in the Special Pads was developed by pro riders in the MX, Supercross, Enduro and Off-Road world where performance and good durability are essential.
Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
This is one of the few plastic parts on the DR650 that can ruin your day if it breaks or fails on you. This gear helps drive the oil pump to circulate oil throughout your entire motor, without it, your motor will fail entirely. The idler gear is not known for being a common failure point in the DR650 motor but, it has failed riders in the past. Usually in the form of a broken gear or stripped teeth. Upon inspection, look for any kind of crack, chipped or missing teeth on the gear. It is not a complicated repair to swap an old gear for a new one, as the best time to replace it is when you've opened up the clutch side case cover for another repair i.e., (NSU screws or clutch hub bushing replacements). This is an O.E. Suzuki part.
Ride in warm temperatures a lot? Worried about your motor oil just getting too hot? The Trail Tech Universal Fan Kit mounts up to the backside of the DR's oil cooler to draw cool air across it and keep those oil temps down. An electronic temperature sensor mounts to the fan, no need to cut any fluid lines, and automatically turns the fan on when needed to keep the temperature in the optimum range.
The activation sensor can be set wherever you like to keep the temperature right where you want it. Backlit for easy viewing anytime it also includes a volt meter.
The complete shock upgrade kit - a shock spring of your choice, Race Tech Gold Valve kit, detailed instructions and a bottle of quality shock oil to complete the job. Everything you need to transform your mushy stock shock into suspension that really works.
Designed and built for Dual-Sport and Adventure bikes, the Nitron Adventure Series R1, R2 and R3 shocks offer exceptional road and trail performance. Using billet aluminum components, a large heavy-duty 16mm piston rod and a high-flow capacity 46mm piston, this shock flows much more oil for a more consistent, fade-free performance than most other shocks.
Nitron shocks are custom built for your specific weight, if you have a passenger or luggage add that weight as well. Lastly your riding conditions; do you ride mainly paved roads, dirt roads, trails? Please provide a percentage of each you ride. This information is essential to the building of the shock. Enter this in the comments section of the shopping cart when you check out, or feel free to call and place your order over the phone.
Progressive Suspension springs offer a soft initial spring rate for a plush ride. Progressively wound design provides increased resistance to bottoming as spring compresses. These springs are significantly stiffer than the wimpy stock springs. Spring rate spans the .45-.62 kg/mm range.
Polyurethane drive cushions for the DR. Polyurethane has a higher abrasion, cut, and tear resistance than rubber as well as much better resistance to chemical breakdown. This will offer longer life and better damping when compared to the stock rubber cushions.
Stock chain guard crack and crumble on you? Won't happen to this unit CNC machined from 2.5mm marine grade aluminum. Polished to a beautiful sheen that will give your DR that little twinkle as well as better protection.
Replace your lower chain roller with this high quality roller with 2 sealed ball bearings. The stock roller has no bearings. It's just a plastic wheel riding on a bolt. Ball bearing chain rollers are smoother, quieter and last longer.
The DR650 is rather hard on the cush drive rubbers. Replace these any time you feel excessive play in the sprocket carrier hub. Excessively worn dampers can cause the cush hub bearing to fail - which will ruin your sprocket carrier. Sold as a set of 6 rubber dampers.
Greatly eases basic chain maintenance, tire changes, parking, cleaning, etc. All necessary hardware is included. Installs using basic hand tools. Tough black powder coated finish.
For riders who wish to run the centerstand and the lowered footpegs we recommend installing a Warp 9 brake pedal. The Warp 9 pedal is arched to give the necessary clearance under the pedal.
Many riders choose to convert over from the stock 525 to a 520 chain. Besides being lighter and less expensive, a 520 chain is more readily available as well as having more sprocket size options.
These Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. These units have been given the seal of approval by the ProCycle staff for both performance and ease of installation. No disassembly of your forks, no drilling of damper rods. Just change the oil over to 5w and install the DDCs under the springs and hit the trails.
We start with an Excel rim, OEM hub, and Buchanan's heavy gauge stainless steel spokes. Rims and spokes are precision machined for a perfect match to your bike. Optional upgrades include billet a Warp 9 hub available in 5 colors and SUN rims available in 3 colors.
Our pro shop then laces and trues your wheel to perfection, giving you the highest quality custom wheel available.
New OEM or Warp 9 hub with bearings and seals installed
2.50 x 17 Stock or street (Sun rims are 2.75x17)
2.50 x 18 Off-road (Sun rims are 2.75x18)
4.25 x 17 Supermoto
Add a tire to your wheel order and we will throw in a tube and mount and balance it at no additional charge.
Custom made: Please allow 2-3 weeks for delivery. Cannot be canceled.
Supermoto forged tubeless wheels. These wheels are machined from forged alloy blanks. A 3.5 x 17" front wheel matched to a 4.25 x 17" rear. Hub can be changed out to fit future bikes. Includes brake rotors, sprocket, cush hub and color matched 90 degree valve stems.
For additional color options please call / email for availability.
Comes complete with:
Warp 9 front supermoto machined wheel
Front oversized floating 320mm rotor and bracket
Warp 9 rear supermoto machined wheel
Cush rear hub
Apex rear rotor
Sprocket
Includes a color matching (to the hub) 90 degree valve stems Rear hub is Cush drive and includes 6 Cush drive rubbers All rotors and sprockets bolt patterns are OEM spec. Tubeless design offers further weight savings and complexity over spoke wheels Front wheel without rotor is 10lbs 2 oz Rear wheel Cush drive no rotor or sprocket is 15lbs Rear wheel direct drive no rotor or sprocket is 14lbs
Add tires to your wheel order and we will mount and balance them at no additional charge.
Custom made: Please allow 2-3 weeks for delivery. Cannot be canceled.
Complete set of 'Adventure' wheels. These are the same rim sizes as used by the BMW GS and other big adventure bikes. The 19" front and wide 17" rear will give you great twisty road handling on the pavement while still being dual-sport friendly.
We start with Excel or Sun rims, OEM or upgrade to Warp 9 hubs, and Buchanan's heavy gauge stainless steel spokes. Rims and spokes are precision machined for a perfect match to your bike.
Our pro shop then laces and trues your wheels to perfection, giving you the highest quality set of custom wheels available.
New OEM or upgrade Warp 9 hubs with bearings and seals installed
Excel 2.5" or Sun 2.75" x 19" front rim
Excel or Sun 4.25" x 17" rear rim
Buchanan's stainless steel heavy gauge spokes and zinc-plated nipples
Add tires to your wheel order and we will throw in tubes and mount and balance them at no additional charge.
Custom made: Please allow 2-3 weeks for delivery. Cannot be canceled.
Race Tech Cartridge Emulators make damper rod forks perform like well-tuned cartridge forks. Emulators are tunable valves that sit inside your forks on top of the damper rods and are held in place by the fork springs. Simple to install and completely tunable for all conditions and rider preferences.
Protect that vulnerable rear master cylinder with this thick aluminum guard from JNS Engineering. CNC laser cut then formed and given a clean black powder coat finish. Includes new button head screws and aluminum spacers.
Warp 9's CNC shark fin rear rotor protector. To make installation super-easy this fin bolts to a brand new CNC machined caliper bracket. Just remove your existing caliper bracket and remove the pins, install them on this new one and then put the caliper and fin back on.
Corbin seats are carefully designed to provide a comfortable riding position. They are firm and supportive which allows you to ride all day without fatigue unlike the stock seat.
Comfort Cell Foam retains resiliency and doesn't crush down like the stock foam so they can build a lower seating platform. This gives you better ground reach and a lower center of gravity. For the off-road enthusiast they were sure to leave enough nose to allow you to slide up the tank and get through the corners faster. Or slide back to skim the front end over the whoops.
The default vinyl choices are black 'carbon fiber' on top and 'asphalt' on the sides, 'no welts', black logo. You can view all of the available materials and colors through the link below. If you would like your seat built with something other than the standard choices please state specifics in the comments during check out.
Your choice of an aluminum bolt-on foot pad or a steel weld-on unit. Each will make the footprint of the stock side stand considerably larger, preventing your DR from tipping over in soft terrain. The bolt-on unit is cut from aluminum and then powder coated black, it comes with stainless steel mounting hardware.
The bolt-on pad and does require use of a drill for installation. The weld-on pad will need to be welded to the stand and then the entire unit painted for corrosion protection.
Pivot Pegz have set a new standard in footpeg performance and quality, and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty.
Pivot Pegz aim is to build the best footpegs in the world and they really do perform as good as they look. Here's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever.
Mega wide 60mm platform
Widest and lightest pivoting pegs on the market
Open design = less mud packing
Unique multi-directional grip pattern
Outstanding build quality
Race proven design and durability
See below for extenders for these pegs to make them true ADV pegs!
Low peg mounts from JNS Engineering. Your choice of a straight 1.5" drop or get that drop and a 1" rearward offset. You can use your stock pegs or click on one of the optional pegs that are made to fit the stock DR650 mounts.
These heavy duty steel mounts are pressed, welded and then powdercoated black for protection. Includes mounting bolts.
Note: These mounts are compatible with the SW Motech Center Stand by adding a 1/8" spacer behind the mounts.
This anodized billet piece, brings a touch of color to your bike. Available in red or blue, it replaces the stamped steel clevis that connects your brake pedal to the master cylinder.
Warp 9 has created a beautiful brake pedal machined from billet aluminum to an 8mm thick work of art. A stainless steel pin eliminates wear in the frame. This pedal has the ability to move the spring loaded brake tip 10mm either way from the center position. The arm is arched to provide clearance for riders who have the lowpeg + centerstand combination.
This plug-n-play kit includes sealed LED headlight assembly and adjustable mounting brackets specifically designed for the 1996-2020 DR650SE. No wiring, soldering, resistors, drilling, or fabrication required however due to the size of the headlight minor trimming on the backside of factory plastic headlight fairing is needed in non-visible areas.
Stock size rear brake rotor laser-cut from high-carbon content 410 stainless steel, then lap cross hatched and heat-treated. Each one then has a high-temp paint applied to surfaces like cooling holes and edges for a clean finished look.
This is a high-quality seat cover offered by Moose for the DR650. This is a replacement cover only, no seat foam and you must install on your existing pan with existing foam.
These plates are made from 4mm thick 5083 aluminum because the extreme abrasion and impact resistance for the full weight of the bike and the rider. The front portion of the B&B Skid Plate bolts to mounts that are permanently attached to the forward motor mount. This means no more trying to hold clamps in place when you take you skid plate off for oil changes or cleaning. Easy off, easy on. All necessary hardware is included in the kit. The plate has foam or rubber wherever there is contact with the frame.
Choose from a polished finish or a black polymer coating.
The ProCycle seat was designed for both comfort and function. Our seat is built with a premium denser foam for those long days in the saddle also giving you freedom to move while standing.
Wide and firm saddle adds comfort on long rides
Narrowing taper up front allows room for knees when standing
The vinyl weave pattern allows airflow between you and the seat
Provides grip down the sides allowing you to hold on with your knees
Available as a Foam and Cover Kit for OEM pan. It DOES NOT include the pan.
ProCycle side panel guards to keep your saddlebags from fouling the side covers. Constructed from mild steel tubing that is powder coated black for nice long lasting good looks.
Add Moose 20L Saddlebags for a very economical luggage solution.
Add Wolfman Rocky Mountain Expedition Saddlebags for a premium luggage solution.
PSR's fin rear rotor protector. CNC machined from forged aluminum and then anodized gun metal in color. Just remove your existing caliper bracket and remove the pins, install them on this new one and then put the caliper and fin back on. It doesn't get much easier. In the event of damage to the fin, it can be replaced separately.
Included in this kit are fork springs, Cogent DDC (Drop in Damper Cartridge) performance cartridges and three bottles of 5w fork oil. Refresh those tired old forks and make them better than new. These DDCs from Cogent are easy to install. No taking the forks apart, no drilling of the damping rods, nothing. Just take them off, flip them over to drain the oil, add new 5w oil, drop in the DDCs and then add the springs and spacers and then install the caps. Preload spacer material is included with the .47 and .70 springs, additional spacers are not needed with the other kits.
This upgrade offers better control off-road as well as on. Less brake dive keeps the fork up in the middle of the stroke on-road and better control off-road whether it be rolling water bars or bouncing off the rocks.
Rider and Gear up to 160lb. = 0.47 springs → 24% stiffer than stock
Rider and Gear 160-225 lb. = 0.52 springs → 39% stiffer than stock
Rider and Gear 225-275 lb. = 0.58 springs → 56% stiffer than stock
Rider and Gear 275-325 lb. = 0.63 springs → 66% stiffer than stock
Rider and Gear 325 lb.-UP = 0.70 springs → 84% stiffer than stock
This 'Bling Ring' replaces the two stock preload/lock rings. The ring is CNC machined aluminum with the additional thickness to provide superior support on the shock body.
The added needle bearing thrust washer will make preload adjustments much easier. The ring then spins much easier against the spring making adjustments quite a bit easier.
This part can easily be added to the Cogent or Race Tech Shock Shaft Assemblies, even after they are built.
To install the Bling Ring on a shock with a stock shaft it must either be disassembled or have the lower clevis removed.
ProCycle Dashboard designed to power multiple electronic devices. It can also be used for accessory lights, heated grips or gear, whatever you like. You can also use the two pre-drilled holes to attach a RAM mount and place your phone or GPS unit on that while charging.
The dash panel is manufactured from laser cut 5/64 mild steel and powder coated black. Also included are 2 weather resistant green LED rocker switches, a voltmeter with two 4.2 amp weather resistant USB ports, a wiring harness with a built in 20 amp fuse/holder, and complete instructions. Everything you need to mount it and connect the outlets back to the battery.
**If you would like the Voltmeter & USB ports to be powered by a "key-on" power source, add the "Auxiliary Power Plug" adapter to your order and you will be able to connect the positive and negative terminals directly into the aux plug behind the cowling for a quicker and easier installation as well.
Made from 1/8" thick stainless steel with dual folded edges for additional strength, these brackets will relocate your passenger pegs down 4" and move them back 1.5". This will give your passenger additional legroom making two-up riding much more comfortable.
All hardware is included for a quick and easy installation.
Complete set of friction plates, HD springs and steel separator plates prevent premature driven plate wear, oil muddying and loss of stack height. Built with swaged aluminum carriers that spread the load on the clutch basket and prevent clutch basket "dogging". Anti-swell, alloy impregnated heavy-duty facings for smooth clutch action. Allows modulation, unlike paper clutches which tend to snatch. Don't forget to add a fresh gasket.
Wraps around your K&N filter to keep water and small particles out of the filter itself. K&N DryChargers are manufactured from a durable polyester material and are pre-treated with a proprietary hydrophobic process designed to prevent splashes of water or mud from saturating your K&N air filter. The DryCharger will also stop small dirt particles; yet add little restriction to the airflow of the filter. The DryCharger can be installed under the Foam Wrap.
Extended float bowl screws from Wirth Machine for your TM40 that use 1/4" size wrench to loosen. Allowing easy access to your jets and float without having to remove the carburetor from the bike. Sold in a 4 pack. Stainless steel threads.
The screws and nuts that hold the Air-box Cover on have a habit of jumping out of the air-box and running away. No idea where they go, but it is far! These cannot be purchased separately from Suzuki but we found some that are perfect replacements. This little kit includes four screws and the square nuts that go into the air-box. We recommend that you put a dab of silicone or something to hold the nuts in so they don't jump ship like the other ones did.
The 790cc Big Bore Kit includes a custom made, forged 9.5:1 piston with rings, wrist pin and circlips. A custom made multi-layer steel head gasket, OEM metal base gasket, tensioner gasket, and cam bolt lock plate and a ProCycle specific big bore cylinder sleeve.
Built cylinders with 790 sleeves installed are usually in stock, but we must have your original cylinder sent to us as a 'core'. These cores allow us to keep up this program and it is nothing more than an exchange - we give you ours, you give us yours.
This Kit Includes:
DR790 Big Bore SLEEVE ONLY (requires your cylinder to be bored and sleeve pressed in. Your local machine shop is the best place to ask for this service.)
Has your TM40 carburetor been sitting for too long and now needs to be rebuilt? Then what you need is this TM40 Rebuild Kit that contains Genuine Mikuni replacement parts.
The OEM foam secondary filter can deteriorate rather quickly. Once that happens, it can allow enough dirt into the engine to do significant damage. Replace your filter now with a high-quality foam filter from industry leader Twin Air.
This filter needs to be oiled like any air filter to work properly.
This brass fuel screw offers a longer head to give you a better hold for making adjustments. This is a nice improvement over the standard extended fuel screw. Kit includes one new screw, spring, washer and o-ring.
Helix brand exhaust springs made from zinc plated music wire. These are the springs we use on our GSXR Mid-Pipe Kit. If you lose one, or break one, these are the direct replacements. Sold as a Pair.
This kit includes 2 needles that have been developed by JD Jetting and manufactured for them to their exacting specifications. These two needles allow a wide range of tuning possibilities and provide correct fuel delivery at any throttle position.
4 Allen type screws for the float bowl are also enclosed should you strip out the stock screws during your tuning process. Complete instructions with photos, jetting suggestions for different set-ups and situations, 4 Main Jets, a new Pilot Jet, and a drill bit complete the package.
Raises compression from stock 9.5:1 to 10.5:1 for more power, torque and snappier engine response. The high quality forged piston from JE is almost a full ounce lighter than the stock cast piston. This makes for less vibration and a smoother running motor. Includes rings, pin, clips, and top end gasket set with valve stem seals and metal base gasket. Fits the standard size stock bore.
Top end gasket set with the addition of a factory Suzuki metal base gasket. A metal base gasket is essential because paper base gaskets will fail in the DR650.
Complete set of engine gaskets and oil seals. Includes the addition of a factory Suzuki metal base gasket. A metal base gasket is essential because paper base gaskets will fail in the DR650.
No repacking required. The LeoVince X3 Enduro is made with TIG welded stainless steel internals and aluminum outer shell. It features a semi-direct chamber design that is maintenance free. It's quiet too! Our own in-house testing showed a 84dB sound level using the USFS J1287 testing procedure. That is a bit louder than stock but significantly quieter than other aftermarket mufflers. It includes a certified Spark-Arrester. This muffler requires a stock muffler joint gasket when used with either the stock headpipe or the FMF headpipe.
By popular demand. This is our own mid-pipe adapter kit for the GSXR exhaust cans. The unique design works with both 3-bolt Hayabusa and 4-bolt GSXR mufflers. It features all stainless steel TIG welded construction with a laser cut adapter. A spring tensioned slip joint allows for heat expansion. A stainless steel hanger strap allows it to attach to your original muffler mounting point. No welding is required. Mid-pipe length is approximately 17" long.
This mid-pipe does not require a stock muffler joint gasket when used with the stock headpipe, the SS Pro-Flow, or the FMF headpipe, eliminating the hump in flow.
Don't forget a fresh seal ring gasket that fits between your muffler and mid-pipe adapter.
The ProCycle SS1 muffler was designed so this existing spark arrester will fit right in. This is also the same unit that is often adapted to the GSXR 40F0 muffler. It fits FMF exhaust as well.
Voyager is the original Trail Tech off-road GPS, designed specifically to meet the needs of off-road riders. With Voyager you can download, record, and share maps while recording vital engine data. The 2.7 inch TFT backlit display is ideal for viewing in any environment and gets easier to read in direct sunlight.
Trail Tech provides a one year warranty and unlimited free phone and email support.
GPS enabled, active compass, elevation readings, distance and the ability to record ride data to SD card
Speedometer and tachometer readings in real time, shows current and total ride time and battery voltage
The 400x240 WQVGA LCD map screen is monochrome, displaying maps in black and white.
Plan routes on the web, then import to Voyager as gray routes ready to ride.
As a new track is recording, a black line appears indicating where you have been.
Voyager integrates with your vehicle using standard Trail Tech vehicle sensors, providing vital ride gauges such as engine temperature, RPM, battery voltage, speed/distance, and more.
At only 4.5 x 2.5 inches, Voyager is a great choice for many types of vehicles from adventure bikes to quads, UTVs and dirt bikes.
12V DC power required, make sure your vehicle has a battery.
This is an extended version of the stock DR650 clutch release arm that is manufactured by Suzuki.
Upgrading to a longer clutch release arm will lighten the pull of the clutch lever through means of increased leverage. This means less fatigue, quicker clutch engagement, easier clutch modulation and longer rides.
The extended clutch arm will not offer a drastic change in clutch pull. If you're looking for a major change in clutch pull at the lever, we recommend getting a Magura hydraulic clutch kit.
In this kit you will get 4 factory replacement bolts to replace any broken or damaged clutch pressure plate bolts on your DR650.
It can be easy to over torque these bolts if not done properly. If one of these bolts is damaged on your DR650, we highly recommend replacing all 4 to prevent any future failures down the trail.
Rotors are laser-cut from high-carbon content 410 stainless steel then lap cross hatch ground and heat-treated. The finished rotors are mounted on a floating black steel carrier for durability and strength.
The oversize floating pins are CNC machined stainless steel rivets with stainless wave washers to ensure they will not crush as more traditional steel pressed rivets can. Finally, high-temp paint is applied to surfaces like cooling holes and edges to provide a clean, finished look.
Their rear racks are great for adding the extra storage needed for your next adventure. They are the perfect size for a backpack or small duffel bag. Their steel racks are built to handle any riding style you throw at them, now Rotopax ready!
This is the ENDURO Series DR650 rear rack which measures 10 inches wide and 12 inches long.
Great for carrying cargo, duffel bags/backpacks, and mounting Pelican, Seahorse, or any other hard cases. Givi compatible.
Holes are in place to accept Rotopax mount with no drilling required.
Stainless steel mounting hardware and instructions included.
Fabricated with mild steel, MIG welded, and finished with a semi gloss black industrial grade powder coat.
Weighs 3 lbs, 10 inches wide, 12 inches long.
Works with stock tool bag. You can remove the seat with no interference from the luggage rack.
Rear rack only, no Rotopax mount or side racks included.
Geared for the do-it-yourselfer that already has a TM40 or HS40. This kit supplies everything you need to convert it for use on your bike.
Kit includes intake and air boot adapters, throttle cables, choke knob, accelerator pump nozzle, a wide selection of main and pilot jets plus a TM40 tuning manual.
Transform your ride
MadStad's patented mounting system allows riders to adjust the height and angle of their motorcycle windshield resulting in much smoother airflow, better wind protection and a more comfortable ride than any fixed windshield can provide. Better still, this dual-sport version pivots the shield down and forward to get it out of your way for off-road riding!
What's included in the kit
Their complete bolt-on system is custom-made for your bike and includes everything needed to mount and position the shield. Your bike will not require any modification.
A set of MadStad adjustable dual-sport brackets
The acrylic windshield
The MadStad brackets bolt to the top of your fork clamps and are completely free of the handlebars. You can adjust the shield for the optimum height, angle and airflow for comfortable street and highway riding. When going off-road you can leave your comfort adjustment as-is and pivot the entire system down and forward in front of the headlight so you can get it out of your face completely. When it comes time to hit the pavement again, simply pivot it back up and you are back in street riding comfort mode.
This kit includes one OEM drive plate retaining wire & one OEM inner steel drive plate.
If you've ever changed the clutch on a DR650 you will be familiar with the extra steel plate at the bottom of the stack that is locked in place by a very thin metal wire.
Generally, when you do a clutch replacement on the DR650, you do not need to remove or replace these items. If you do need to (or if you have already) you will come to realize this wire is not very strong and is prone to breaking if not treated with care during the removal / installation process.
The Rally windscreen from Parabellum is the perfect protection from wind and debris without sacrificing technical off-road capabilities. This is an upright rally type windscreen that looks aggressive and performs well under all types of riding. Designed primarily for the off-road / dualsport enthusiast, this shield keeps pressure off the rider's chest while commuting from home to adventure and back.
Mounting is accomplished by drilling two holes on each side of your headlight cowl using the provided template. The shield is 14 inches tall, 11.5 inches wide at the bottom narrowing to 8.5 inches at the top. Made from military aircraft grade cast acrylic.
This unit will not fit properly on '90 to '01 DR650 headlight cowls.
This is a simple three piece kit you can install in minutes that cleans up the stock DR rear-end. We use the 250 taillight that fits perfectly into the pocket of the stock taillight on the DR650 fender. It is smaller, looks great and is out of harms way more than the stock unit. It is a total 'plug-n-play' as the wire pigtail plugs right into the DR650 harness just like stock. Then we use a small LED light to keep you legal and illuminate your license plate, which gets mounted to our custom stainless steel bracket, eliminating the stock ugly plastic mount.
In the event of a crash or even just a dropped bike, these heavy-duty crash bars will prevent major damage.
The powder coated 1" steel tubing is bolted to the sub frame of the bike with two attachment points on each side, preventing them from rotating in the event of a low side.
The guards also feature aircraft grade aluminum plates that can be inexpensively replaced without needing to purchase a new set. Think of them as protection for your protection.
They use highest grade commercially available 12.9 (177,000 psi in tensile strength) wherever possible. Rest assured that you are getting the best material commercially available.
Most skid plates will require notching or modification to avoid interference.
T-Rex Racing skid plate for the Suzuki DR650, designed to protect your bike from dirt, mud, and other debris.
Made from precision CNC machined aircraft grade aluminum finished with black powder coating for durability. Rest assured that you are getting the best material commercially available.
Specifically designed to work with T-Rex Racing engine guards, and center stand.
This new unit from JNS will protect your cases from the damage caused by a thrown chain, and will also keep your pants, boots or foot safe from your countershaft sprocket.
The case saver portion is laser cut from 0.25" aluminum and then has the 0.19" aluminum countershaft sprocket cover welded to it and the entire unit is powder coated black.
All the mounting hardware is stainless steel with machined aluminum spacers also included.
If you have a 16t front sprocket, mounting modification may be needed to fit. Install the case saver on the bike without the top spacer and bolt. This provides a little extra wiggle room. Add the top spacer and bolt after the bottom bolts are loosely threaded.
Savvy DR650 owners will remove the upper chain roller. You can use this stainless steel button head screw to plug the threaded hole. Suzuki did not make the upper roller mount strong enough. If you don't remove it yourself the chain will likely do it for you - along with a chunk of metal out of the frame.
Replace your lost or broken stock plastic chain guard with a JNS aluminum one. Laser cut, CNC formed, TIG welded, and powder coated a beautiful satin black. This is a direct replacement for the stock unit.
Please note that this unit is a bit wider than the stock one and will have to be trimmed if you are running a big fat SuperMoto wheel/tire.
Constructed of 3mm-thick (1/8"-thick) aluminum for heavy-duty, light-weight protection. Baseplate includes side protectors that wrap around the engine case to provide both bottom and side protection.
Have your tank cushions worn out over the years? Have you lost one or more while working on your bike? We have new upper and lower tank cushion rubbers.
This kit includes the original hardware, upper, and lower cushions.