Search Products

The Mini Powercore 4 is the best bang for your buck performance exhaust system out there.

Offered as a standard Mini Powercore 4, or as a Spark Arrestor Version, the Mini Powercore 4 features a Hi-Flo stainless steel core and formed end caps, an aircraft grade aluminum canister and a durable stainless steel header. It is pounds lighter than stock and you will swear the motor has been bored and stroked with the first twist of the throttle.

Geared for the do-it-yourselfer that already has a TM40 or HS40. This kit supplies everything you need to convert it for use on your bike.

Kit includes intake and air boot adapters, throttle cables, choke knob, accelerator pump nozzle, a wide selection of main and pilot jets plus a TM40 tuning manual.

Tune your stock carburetor for better power and response, easier starting and quicker warm up. Mikuni main and pilot jets.

• Main Jets: #110 & #112.5
• Pilot Jets: #17.5 & #20

• Increased air flow over the stock air filter
• Designed to increase horsepower and throttle response
• Designed to fit inside the factory air box
• Larger surface area over foam filters which offers longer service intervals in dusty conditions
• Four layers of premium cotton gauze provides outstanding filtration
• Washable & re-usable, never wears out
• One filter will last the lifetime of your bike

Thick, flat foam, greaseless sealing ring ensures maximum contact with your airbox while acting as a breathable gasket for increased air passage

Features:

• Coarse open-pore foam catches airborn dirt, grime, and sand
• Fine open-pore inner foam acts as second filter to trap the smallest particles while ensuring maximum air passage
• Adhesive withstands repeated cleaning
• Smaller than stock to increase air space and circulation around filter
• exclusively formulated adhesive withstands repeated cleaning. even with harsh solvents or gasoline
• twin air filters are slightly smaller than stock filters to increase air space around the filter and improve circulation

High-performance, high-flow filter element and filter base for the TT-R 125.

• Replaces stock filter and base
• Filter base is made from HDPE plastic
• 3 times larger than stock filter!
• Adds almost 1/2 horsepower
• Designed to fit inside the factory air box

A quality foam Air Filter to replace the stock one. Uses the same guide and frame as the stock unit. It requires foam filter oil to properly trap dirt particles. Don't forget the Evolution Air Filter Oil kit from No Toil.

• Designed to fit in the factory air box exactly like original filter
• The best selling replacement air filter for competition motorcycles and ATVs
• Unique two stage design allows for easy and complete cleaning
• Dual layer of foam, can be serviced separately
• Thin Ultra Seal base is virtually impossible to tear and has a built-in "Grease Groove"

• Designed to fit in the factory air box exactly like original filter
• The best selling replacement air filter for competition motorcycles and ATVs
• Unique two stage design allows for easy and complete cleaning
• Dual layer of foam, can be serviced separately
• Thin Ultra Seal base is virtually impossible to tear and has a built-in "Grease Groove"

• Unique triple stage foam filter designed for the most extreme conditions
• Eliminates the need for power robbing dust covers and outerwear covers
• Increased protection against silt, water, and sand
• Allows for extended filter service intervals
• Can be cleaned, re-oiled, and re-used like a 2 stage filter
• Used by factory off road teams around the world

Sold in 6 packs

• Compatible with many air filter boxes. Easy to install by drilling 1’’ holes in airbox housing and snap fitting vents in.
• May be cleaned and re-oiled
• More air flow allows you to add more fuel to your intake mixture, increasing performance.
• 1" Diameter

Not legal for use on pollution controlled vehicles in the state of California.

Allows your bike to breathe much better giving you better response and performance.

• Breather Filter
• ProCycle Jet Kit which includes jets, needle, extended fuel screw, drill bits and Allen bolts to replace phillips (JIS) head bowl screws and detailed installation instructions
• Choose Twin Air, DT1, or K&N filter with ProCycle filter wrap
• OPTION - Twin Air breather filter (replaces standard breather filter)

The OEM foam secondary filter can deteriorate rather quickly. Once that happens, it can allow enough dirt into the engine to do significant damage. Replace your filter now with a high-quality foam filter from industry leader Twin Air.

This filter needs to be oiled like any air filter to work properly.

Only for bikes with the stock BST40 carburetor!

Replace your handlebar mounted choke with this simple knob mounted directly on the carburetor.

Available in short or long reach.

Long reach is easier to use while wearing riding gloves.

Works for either the stock BST or Mikuni TM40.

Rebuild your crusty carburetor with parts from the same manufacturer the OEM companies use. Included in the kit are all necessary gaskets, O-rings, float valve and jets you need to rebuild your carburetor to like new condition.

Here is the O-Ring that fits in the carburetor manifold. This is the manifold that holds the carb up to the cylinder head. The O-Ring mounts between this manifold and the cylinder head. When this O-Ring fails it allows air into your cylinder and makes your Air Fuel ratio too lean which causes the engine to run too hot.

Replaces the stock 2 wire Ruckus fuel level unit with a 3 wire unit that allows use of a multi-level fuel gauge.

Want an amazing increase in throttle response? More power over a much wider range? The Mikuni TM40 does all of that plus runs smoother at lower RPMs and pulls taller gearing with ease.

Our complete kit comes with alloy adapter rings bonded to the genuine TM40 carburetor body for a firm reliable fit in the stock air boots. We also include new low friction cables, an extended fuel screw, complete instructions along with a wide range of extra jetting for fine tuning. It even has a vacuum port for the stock fuel petcock.

The carburetor comes pre-jetted for the typical mods: performance pipe and modified air box, or we can set it up for your particular bike before we ship it out.

 Instead of the tough to reach choke knob, all TM40's come with a remote choke and bracket. This makes it easier to reach the knob, especially if you have an oversize tank.

All the advantages of a flatslide pumper carburetor at a much friendlier price than a Keihin FCR.

Our complete genuine Mikuni TM40 pumper carburetor kit comes with alloy adapter rings bonded to the carburetor body for a firm reliable fit in the stock air boots. We also include new 3" longer than stock throttle cables, a remote mounted choke knob, complete instructions along with a wide range of main jets and pilot jets for fine tuning or to accommodate bikes with extensive modifications.

Heavy-duty springs help prevent clutch slip in high-performance motors.

• Custom wound from chrome-silicon wire
• Preset for long life
• Higher spring seat pressure to resist clutch slip

Replacement friction plates and drive plates.

Designed to improve the life and durability of your clutch, Barnett's "Dirt Digger" provides better rideability with less slippage compared to stock.

• Carbon fiber friction plates
• Tempered steel drive plates go through a vibratory de-burring process and then are quality checked for flatness to provide optimum performance.
• Heavy duty clutch springs are pre-set, shot-peened, and heat treated for performance and durability.

Heavy duty springs help prevent clutch slip in high-performance motors.

• Custom wound from chrome-silicon wire
• Preset for long life
• Higher spring seat pressure to resist clutch slip

Replace your worn out clutch with a high quality Clutch Kit. This kit includes new friction discs for your clutch pack.

Please note: kit includes friction discs only, steel plates and springs not included.

These valve springs are required when using the BBR High Performance camshaft for the CRF150/230F.

• Built from the highest quality chrome-silicon wire
• Fully shot-peened and preset for long life

7.48mm diameter - Includes three valve shims of each size from 1.20 to 3.50mm in .05mm increments.

141 shims in total. 0.57 cents per shim! Does your local dealer have the shims you need?

High performance camshaft for the CRF150F 03'-05' and CRF230F. Higher lift and duration than stock.

• Adds 1+ HP to fully modified motor
• Makes more aggressive race-style of power
• Bike still starts easily and idles smooth

CRF230F 240cc Kit:

• 67mm piston, pin, clips, and rings
• New (not reground) high-performance camshaft
• Includes heavy-duty valve springs
• Includes head and base gaskets
• Requires boring of your stock cylinder to fit the new piston

Big bore kit for the 2003-2005 CRF150F. A simple bore in bore kit that includes BBR's high performance camshaft and valve springs for added performance. This cam features higher lift and duration than stock. Complete kit includes piston, rings, pin, clips, BBR MX cam, valve springs and gaskets. This is the quickest way to add the most power to your bike. Great when combined with our exhaust system, Rev-Box, and Free-Flow airfilter. Requires machining of stock cylinder for installation.

• Adds up to 3.5 HP
• 67mm piston, pin, clips, and rings
• 10.75:1 compression ratio
• Includes head and base gaskets
• Makes more aggressive style of power
• Bike still starts easily and idles smooth
• Same camshaft as used by the BBR Race Team
• Requires professional boring of your stock cylinder

285cc big bore kit includes:

Wiseco piston 78.00/+5.00 10.5:1 (with rings, pin & clips): 

• All Wiseco Pistons are forged from high silicon, low expansion aluminum which offers superior strength, reduced weight, improved heat transfer, and longer life.
• Diamond turned finish from one of the many CNC computer controlled turning centers guarantees you a perfect finish with no size variation. Wiseco pistons can be installed in any of today’s cylinder bore compositions
• Wiseco’s state-of-the-art computerized manufacturing facility is dedicated to supplying both the high-perfomance racer and recreational enthusiast with the finest forged piston available in today’s market place.

HotCams stage 1 camshaft:

• High-performance racing camshafts
• Stage 1 performance camshafts are drop-in cams that are designed to be used with stock valve springs
• In most applications, Stage 1 cams deliver more torque.

Complete top end gasket set:

• High-tech materials provide unmatched reliability and performance
• Rebuild the engine with total confidence as each set is designed for durability and accurate fit
• Oil seals are genuine OEM replacement seals
• Performance sets designed for a piston replacement
• Includes every gasket, O-ring and seal required to rebuild a top end; valve seals, head, base, exhaust, tensioner, and other misc. gaskets and O-rings
• Does not include formed rubber valve cover gasket
• High-compression kits use .012" thick base gaskets to raise compression
• Cost-effective way to raise compression without expensive high-compression pistons or cylinder head work
• All gaskets made in the U.S.A. 

This is a great combination and a big 'bang for the buck' performance increase. 

No re-sleeving required. You will have to have your cylinder bored to fit the larger piston.

Outer Clutch Cover O-Ring, Inner Clutch Cover Gasket, Stator Cover Gasket.

Sold individually, not as a kit

Unless you have managed to bash yours on a rock, this is an item of pure bling, but hey, there is nothing wrong with that! This CNC Oil Filter Cover is made from A7009-T6 aluminum with the 'Zeta' logo machined into the front and anodized in blue to really stand out on your Yamaha. It's also lighter than stock.

The idler gear is one of the few plastic components in the DR650 that can significantly impact engine performance if it fails or breaks.

This gear is crucial for driving the oil pump, which ensures proper oil circulation throughout the engine. In the absence of this component, complete engine failure may occur. While the idler gear is not frequently cited as a common failure point in the DR650 engine, failures have been reported, typically manifesting as either a fractured gear or stripped teeth.

During inspection, it is essential to check for any cracks, chipped areas, or missing teeth on the idler gear. Replacing the gear is a straightforward procedure, and it is advisable to do so while the clutch side case cover is already removed for other maintenance tasks, such as NSU screw replacements or clutch hub bushing replacements.

This component is a Genuine Suzuki part.

• Bolts are CNC-machined from high-quality aluminum
• Embedded magnet helps keep bolt in place
• Pre-drilled holes make for easy installation of safety wires

Rebuilding your engine? Here is a complete gasket kit for your TW200. Includes: Head Gasket, Base Gasket, Stud Gasket, Head Side Cover O-Ring, two Valve Cover O-Rings, Base O-Ring, Stud O-Ring, Rocker Shaft O-Ring, two Cam Chain Tensioner O-Rings, Intake Manifold O-Ring, two Valve Stem Seals, Exhaust Gasket, Left and Right Side Cover Gaskets, Pump Cover Gasket, TDC Plug O-Ring, Crankshaft Nut Plug O-Ring, and Oil Filler Plug O-Ring.

Superior Filtration:

This should be the last oil filter you will ever buy. Made from laser cut, medical grade, 304 stainless steel micronic filter cloth, this filter provides 200% more filter area than other filters in many cases. Most good paper filters will pass particles in the 90 to 95 micron range, and some tested, as much as 300 microns. Sand is about 125 microns and a white blood cell approximately 25 microns. Scott's stainless filter catches items down to 35 microns "absolute". The pleat seam is welded, able to withstand up to 600 degrees, not glued, like paper filters.

Sized perfectly for adult back-yard racing or fast/aggressive mini riders. This is the most important upgrade you can make for an adult sized rider. The stock suspension is too soft for most adults and aggressive kids. Fits stock shock.

• 30% stiffer than stock
• Preset and stress relieved for long life
• Custom wound from aircraft quality spring steel
• Powder coated finish

Sized perfectly for adult back-yard racing or fast/aggressive mini riders. This is the most important upgrade you can make for an adult sized rider. The stock suspension is too soft for most adults and aggressive kids.

• 30% stiffer than stock
• Preset and stress relieved for long life
• Custom wound from aircraft grade spring steel

Here is everything you need to upgrade your TW200 front suspension. Kit includes: Heavy Duty Fork Springs, Cartridge Emulators, Oil Seals, Dust Seals, and 10w Fork Oil. Just choose the spring rate you want and enjoy your TW even more!

Stock Spring Rate is .50 kg/mm. The .60 kg/mm springs are 20% stiffer than stock while the .70 kg/mm is 40% stiffer than stock.

Installation requires disassembling your forks and drilling out your damper rods.

The complete fork upgrade kit - your choice of springs and Race Tech Gold Valves. Also includes a set of top quality fork seals and 5W fork oil to complete the job. Everything you need to transform your mushy stock forks into suspension that really works.

You can select from various straight rate springs to customize the package to your needs.

Stock Spring Rate for XR650L: 0.44 kg/mm

Kit includes all the fork bushings, o-rings, snap rings and washers. This kit comes with what you need to completely rebuild your front fork bushings.

• Bushings are dyno-tested to 500,000 strokes with less wear than OEM bushings
• Kit includes two slider bushings and two leg bushings
• Kit includes all copper washers and O-rings
• Kit includes two fork seal snap rings

Kit includes all the fork bushings, o-rings, snap rings and washers. This kit comes with what you need to completely rebuild your front fork bushings.

Low friction 'triple lip' seal design. Oil seals last 3-4 times longer that OEM seals. Kit includes fork seals and dust wipers.

Seal profile is engineered to create equal pressure in each seal lip; equalized seal pressure creates less drag and longer seal life.

Patented MAX-LIFE has a coefficient of friction up to 3 times less than the OEM seal material

Triple-lip seal design

Dyno-tested to last 3 to 4 times longer than OEM seals

Directional ribs allow seal to be installed easily

Kits include fork seals and dust wipers

Complete kit to replace the bearings and seals in the DR350 shock linkage. Includes the lower shock bearing.

• Includes the lower shock bearing and all other parts necessary to rebuild the suspension linkage
• 52100 bearing steel and hard-plated spacers resist wear and rust
• Each kit includes the lower shock bearing, all the shafts, seals and spacers in the link, link arm and lower shock mount

Damping Rod style forks are notorious for being too harsh, too mushy and too easy to bottom. Gold Valve Cartridge Emulators remedy this problem by controlling the compression damping with a tuneable valve. The Emulator sits on top of the damping rod and is held in place by the main spring.

Simply put; Emulators make damping rod forks perform like well-tuned cartridge forks. Installation and tuning for any condition or rider preference is very straight-forward. 

Simple to install and completely tunable for all conditions and rider preferences.

Made from the latest generation of computer design and control metal cutting equipment for maximum durability. Made exclusively from the finest Japanese 545C high carbon steel. 

All sprockets are heat-treated and hand-finished to meet or exceed the highest possible quality standards.

Rear Sprocket

Note: 2002 and later models have a 10mm sprocket bolts. 2000-2001 models have 8mm sprocket bolts.

428 x 130 links. High Quality non-ORing chain. Rust-resistant gold plated chain for high powered racing machines.

Fully encloses the chain to guide it onto the rear sprocket. Stainless steel hardware, anodized aluminum plate, and plastic buffer for low friction and noise. Saves expensive engine cases.

Chain slippers undergo degradation over time due to friction associated with the chain's movement. To maintain optimal operational performance, it is advised to replace worn components with authentic Honda parts.

Complete bolt-on and go rotor assemblies. Made with forged aluminum center hubs high-friction billet steel rotor rings and sturdy riveted construction. Excellent choice when upgrading or replacing OEM brake rotors.

Sold in pairs.

High performance EBC brake pads.

• The "HH" friction rating is the highest in the industry
• Provide maximum brake effect
• Lasts twice as long as organic pads

This is a complete kit that replaces both front and rear brake pads.

GBrakes Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.

The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.

• Significantly improves response and feel over factory rubber lines
• Largest performance improvement for your money over any other braking upgrade
• Stainless steel hose resists abrasion and puncture
• Teflon core does not degrade over time like rubber lines
• PTFE Dupont 64 Teflon® hose
• Feature a heavy-duty stiffener sleeve and route just like the factory lines
• Proprietary, premium fittings
• Banjos utilizes a unique machined channel and sealing surface for leak-free installations
• R&D and engineered in the USA
• GBrakes USA controls the manufacturing process, ensuring the highest level of quality control

Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.

Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.

Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.

Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.

Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.

The rubber coated outside diameter creates an optimum seal at the hub.

Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.

Rear wheel bearing kit. Includes a new dust seal and the bearing and seal for the cush drive hub. All bearings are sealed on both sides.

Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.

Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.

Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.

Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.

Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.

The rubber coated outside diameter creates an optimum seal at the hub.

Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.

The plastic fitting that secures the stock choke cable to the carburetor is delicate and easily broken. A broken fitting can cause hard to solve idling and running problems.

CNC machined from billet aluminum and anodized black or blue. If you want to retain your handlebar mounted choke this may be the solution.

  These no longer fit the new version of the ProCycle Remote Choke Cable. Will not work with the long or short reach choke knobs.

The indestructible, yet lightweight steel tube construction offers the best angle and ground clearance, makes it easy to jack up and provides stability - whether it's during maintenance or on the road. In most cases, you will no longer need to buy an additional swing arm stand. During long downtimes in the winter months, the centerstand helps take the load off your tires.

• Stands securely when traveling with lots of luggage and during maintenance
• Bike-specific design for easy mounting and high cornering clearance
• Easy to lift up the motorcycle
• Outrigger for optimal leverage
• Best corrosion resistance due to sand blasting and powder coating of the surface
• Made of robust steel
• Total Weight: appr. 1,6 kg / appr. 3.6 lb

A billet aluminum side-stand from PSR. This is the side-stand you want when you are using lowering-links.

Has many height settings from stock to 2" lower, a must have when lowering your bike. Available in anodized black.

Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a more plush and active ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.

These features combine to offer a custom seat feel, and provide greater enjoyment and increased range on a long commute, or Dual-Sport ride!

The Complete Seats come assembled with an aftermarket pan and ready to ride.

"Will not fit the Rally model"

Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a more plush and active ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.

These features combine to offer a custom seat feel, and provide greater enjoyment and increased range on a long commute, or Dual-Sport ride!

Seat Concepts seats are constructed using a foam material that is higher quality than OEM seat foam. Their proprietary formula is plush, while still offering the necessary amount of support. Their unique comfort and shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.

These great features combine to offer you a custom seat feel, and provide greater enjoyment and increased rangefor long commutes, or Dual-Sport rides!

The Complete Seats come assembled with an high quality aftermarket pan and ready to ride.

This DOT kit features a unique halo daytime running light which glows white or amber and a specially designed adjustable steel mounting bracket.  The wiring connection is plug & play.  No cutting, no drilling, no electrical modifications! Installation takes 5 minutes.

The low beam has a nice uniform pattern and a proper upper cut-off.  The high beam throws light far and wide.  

Low Beam: 20W, 2,800 Lumens
High Beam: 35W, 4,800 Lumens
Color Temperature: 6,000k
DOT & SAE Compliant
CE, RoHS, ISO9002, IP67

Taillight and brake light Attaches to the top of the rear fender. Dimensions: 3 1/2" wide x 2" long x 3/4" tall. D.O.T. approved.

Reproductions of the original DR650 factory turn signals. Save a bundle compared to the $70+ each cost of the OEM signals. The wire pigtails plug directly into the factory harness. No cutting or splicing necessary. Choose original style amber lens or clear lens with amber bulb.

If you just installed aftermarket LED turn signals or an LED integrated tail light and your turn signals are flashing way too fast, or perhaps simply staying on completely, you're at the right place to find the solution! The TST Gen2-SK LED Flasher Relay fixes what we call "hyperflash". It slows the flash rate down to a pre-set 85 cycles per minute but can be sped up or slowed down using the adjustment dial located within the unit so you can get the exact speed you are looking for. The plug-and-play installation means that you don't need to splice in any load balancing resistors that generate unnecessary heat and require splicing into your stock wires. Simply remove the stock relay and install your new TST relay and your wiring job is done. It's that simple!

• Slows turn signal flash rate down to an adjustable 85 cycles per minute when turn signals are experiencing hyperflash or stay on continuously
• Adjustable turn signal flash rate enables you to speed up or slow down the flash rate to fit your preference
• Plug and play installation meaning no cutting, splicing, or soldering
• Replaces the stock relay and fits like OEM
• No need for cumbersome and heat-generating load balancing resistors
• Flexible relay housing enables easy access to the flash rate adjustment dial inside of the relay unit

Please make sure your bike uses a 2-pin relay for the signaling system. If your bike has hazard lights it may need the 4-pin relay. Please also note the pin configuration and make sure it matches what is on your bike. It is very important to verify fitment before making your purchase.

This clever carbon fiber wrap can either hide your ugly off road sticker or give you a place to attach your sticker so that you don't leave that sticky glue on your fork leg. 

Easy snap on fit for most larger displacement motorcycles. Fits on the upper section of upside down forks or on the lower section of conventional forks. 

Does not fit smaller forks like those on the TW200 or XT250. 

• Extremely strong plastic construction
• Protects the swingarm of the motorcycle from impacts with external obstacles
• Easily attaches to the swingarm with magnets and rubber bands, which allows quick removal of the protections in few seconds to wash and/or maintain
• Intuitive and immediate reassembly in a few seconds

Protect your Kawasaki KLX250 or KLX300 with T-Rex Racing's heavy-duty skid plate engineered for maximum durability and performance. This premium aluminum skid plate shields your bike's engine and undercarriage from rocks, roots, and trail debris during aggressive off-road adventures. 

Precision-manufactured for perfect fitment, this bolt-on protection features reinforced mounting points and lightweight construction that won't compromise your bike's agility. 

Easy installation with included hardware makes this essential upgrade perfect for trail riders, enduro enthusiasts, and dual-sport adventurers seeking reliable undercarriage protection for their Kawasaki motorcycle.

Heavy Duty replacement Voltage Regulator. More robust, but lower cost than the factory unit.

Designed to enhance overall performance when installing a high-flow jet kit. This CDI box enhancements include:

• Altered ignition advance curves
• Wire lead for a tachometer

This unit may also be used to replace a defective CDI box on a stock machine. 

Please note that the internal circuitry of Rick's CDI unit necessitates the engagement of the clutch or kickstand neutral safety switch for proper operation. Specifically, the clutch must be engaged (pulled in) when the kickstand is in the down position. This requirement may not be present in the original Yamaha OEM CDI unit.

This high output stator will allow you to run brighter lights, heated gear, heated grips, etc. From ElectroSport

This is the Restart-Remote for Antigravity RE-START (RS) Powersport Batteries with jump-starting built-in. You no longer need to access the battery to press its Re-Start button in the event you over-discharged the battery. Simply plug this accessory into your Battery’s Charging Cable to remotely awaken the RE-START Battery! No need to remove the seat or a fairing to get to the Battery.

• Compatible with Antigravity RE-START Powersport Batteries
• Plugs into SAE Tip of your existing battery charging cable
• Comes with protective zipper case
• Remote requires 9v battery (not included)
• Not compatible with Automotive Batteries

You have to pull the rotor off the crank of your KLR to access the doohickey. The offset in this factory Kawasaki wrench makes that very easy. It is very difficult to get a standard wrench to hold the crank to get the flywheel/rotor off.

Clymer repair manuals provides step-by-step procedures based upon the complete disassembly of the motorcycle. This hands-on experience combined with extensive research results in a manual that is both user-friendly and detailed. Hundreds of original photos and illustrations guide the reader through every job.

Hose reducer to go from 5/16" line down to 1/4" line. Many bikes have 5/16" carburetor spigots but most aftermarket petcocks are 1/4". This solve the problem of mismatched sizes. Solid brass construction. Can be used to route or repair fuel lines, oil lines or air lines. Barbed ends provide a secure fit.

Security for your fuel tank. Includes 2 keys. Internally vented with a check valve that prevents spillage in case of a tip over.

This anodized billet piece, brings a touch of color to your bike. Available in red or blue, it replaces the stamped steel clevis that connects your brake pedal to the master cylinder.

The new DG RST (Reduced Sound Technology) muffler is the quietest DG muffler and is designed especially for dual-sport machines (Just 89db @ 3200 RPM). A new baffle design dissipates sound waves reducing noise output in a very efficient manner. This new design also stretches out the time between muffler repacks. Included is a Stainless Steel mid-pipe, USFS Approved Spark Arrestor and a new Aluminum end cap.

You may want to consider a new exhaust gasket that goes between the header and the muffler.

No repacking required. The LeoVince X3 Enduro is made with TIG welded stainless steel internals and aluminum outer shell. 

It features a semi-direct chamber design that is maintenance free. It's quiet too! Our own in-house testing showed an 84dB sound level using the USFS J1287 testing procedure. That is a bit louder than stock but significantly quieter than other aftermarket mufflers. 

The installed weight is approximately 8.5lbs and it includes a certified Spark-Arrester. 

This muffler requires a stock muffler joint gasket when used with either the stock headpipe or the FMF headpipe.

DG Performance exhausts help your engine breathe better, resulting in increased throttle response, power and torque.

The V2 Series Slip-On muffler features:

• Lightweight aluminum body
• Stainless steel inlet tube
• TIG welded components
• Great new look

Standard sound level is approximately 98 db and quiet core inserts are available separately.

This Lightweight Slip-On weighs approximately 5.5 lbs and bolts directly to the stock headpipe.

It is equipped with a US Forest Service-approved spark arrestor.

The touring windshield from Parabellum has been designed, developed and tested using all the knowledge and experience of the KLR riders in their own shop. Using the stock mounting points as well as the cowling mounts increases the rigidity of the shield. 

All new fasteners are included. This new design allows you to move your handlebar to different positions and will not interfere with a stand-up position for off-road use.

This shield is constructed of 3/16" military grade cast acrylic that is 17 inches wide at the bottom tapering to 16 inches at the top.

Quality MX style rear fender from Maier.

High-quality, direct replacement plastic kit includes:

• Front and rear fender
• Side covers
• Air box cover
• Radiator shrouds

Yellow kit is only available with white side covers

  Add-on Headlight cowling fits S and SM models not "E" offroad model

This is the brace needed to stabilize the big front fender on the XR650L. This simple bolt-on brace reduces wind buffeting at highway speeds. It also helps carry the weight of a fender mounted tool bag.

Made from laser cut 5052 aluminum, then CNC formed and beautified with a shiny black powder coat. Easily mounts in a few minutes using the included hardware.

Replacement front fender by Maier that will fit great on your TW200.

• All Maier bodywork is made of tough, vacuum-formed high-gloss polypropylene
• Drilling is required
• Colors are OE color matched

Note: The proper way to install this front is to install the stock fender bracket to the under side of new Maier front fender using stock screws and nuts.

Universal off-road front fender. Must be drilled to fit your mounting bolt pattern.

This advanced filter oil & cleaner kit by No Toil is alcohol free, completely biodegradable and compatible with all foam filters.

• Offers superior protection
• Waterproof yet easy to clean

ThreeBond 1342 low strength thread locking compound. This is the ideal retaining compound for small nuts and bolts. Fasteners are held securely but, can be easily removed when necessary. ThreeBond gives this a number 4 rating for exposure to engine oil making it a good choice for internal fasteners as well as external fasteners. 10ml bottle.

MAGURA HYMEC – AN EASY TO INSTALL ALTERNATIVE TO A MECHANICAL CLUTCH.

This system replaces the clutch lever and cable – with a small lightweight hydraulic system for improved clutch control. The Hymec ensures an easier operating pressure, a constant pressure point, no more cable adjustment and smooth clutch actuation to ensure the perfect take-off every time. Hymec significantly improves vehicle performance – it allows the user to feel the point where the clutch releases and actuates. This product has been developed over many years and been tested under the toughest conditions possible in the world of motorcycle off-road sport. It has been used by world champion riders who all agree as to the benefits but it is just as useful to the complete novice who stalls at the traffic lights.

• This system replaces the clutch lever and cable – with a small lightweight hydraulic system for improved clutch control
• Up to 20% less clutch pull
• No maintenance and self-adjusting
• Smooth hydraulic feel with clear and consistent pressure point
• Operates on mineral oil which doesn't draw moisture and won't harm paint or finish
• Forged break-away lever blade with reach adjust is ready to mount
• Clutch safety switch included

Comfortable Oversize (or Fat Bar) Handlebars.

• CR High Bend
• Black in color. 
• Made from 5mm, proprietary, 2000 series T6 aluminum alloy for superior tensile and yield strength.
• Lighter and stronger than regular bars
• No-crossbrace allows flex to reduce shock and rider fatigue
• Oversize 1-1/8" diameter base reduces to 7/8" to allow standard-size controls/grips
• Etched alignment marks for fast and accurate positioning
• Bar pad included
• Works with stock controls and cables.

For bikes with factory 7/8" handlebars these will require the use of a 7/8 to 1-1/8  adapter (sold separate).

License plate bolt with bright white LED light. The simple way to light up your plate.

You can add this cam buckle loop to any 1" flat webbing system and have an instant secure way to tighten your load.

Available in 6 colors.

CONSTRUCTION FEATURES

• Heavy Duty Cam Buckle rated for 2000 pound load capacity
• 1" Flat Nylon webbing

ProTaper Pillow Top Grip with 3-D (Tri-Density) Technology.  Try the grip with the technical advantage of three dedicated rubber compounds.

• Vibrasonix pillow top reduces vibration and cushions impact. 
• Inner core compound perfects the bonding interface with bars. 
• Anti-Rip Tip™ uses denser compound to increase life of grip. 
• Designed to self-clean and shed mud away from outer surface. 
• Tacky gel-like surface compound is perfect for the trail and MX.

Special tool to remove the flywheel/rotor from the end of the crankshaft. You have to remove the flywheel/rotor to upgrade the doohickey.

All that you need to repair and inflate your tire on the road or trail.

• Padded nylon zippered carrying case easily stores inside fanny pack or tool compartment
• Everything needed to repair and inflate tire on the road or trail
• 4" inflator hose accepts threaded cartridges only
• Each cartridge produces 8-9 psi
• Made in the USA

Kit includes:

• 1 - large oblong patch
• 2 - medium size patches
• 3 - small patches
• Thumb buffer
• 0.50 oz tube of rubber cement
• 5 - 4" rubber insert strips
• Insertion tool with screwdriver handle
• Reamer/rasp tool with screwdriver handle
• 3 - 16 gram 3/8" threaded CO² cartridges
• CO² 4" inflator hose

CO² cartridges cannot be transported on an aircraft.

Here is a tool to help you remove a few links from a chain that is too long. A great tool to have in your tool box.

The head of the pivot pin you are going to remove must be ground down level with the side plate before using this tool to push it out. Failure to do that will cause damage to the tool that is not covered by any warranty!

A kit that includes an Axle Wrench combo for your bike with a 19mm for the front, and a 24mm for the rear. Just 7 1/2" long, it is long on leverage, but short enough to fit in even the smallest tool kit.

Also includes a pair of 'trail size' small tire irons.

No more fighting to keep the bead down while installing or repairing your off-road tires. The Bead Buddy holds the tire bead down in the drop center of the rim during tire changes making changes as easy as possible. Machined from tough 6000 series aluminum the Bead Buddy is light weight and compact enough for any tool pack. The Delrin securing thumb screw insures no scratches to your rims.

The Bead Buddy is NOT recommended for use with Bib Mousse tubes.

Motion Pro T-6 Combo Lever has a hex box wrench for your axle nut on one side and a perfectly contoured tire spoon on the other. Manaufactured from lightweight forged T-6 aluminum with a hard anodized finish. These beauties are just under 10 inches long and weigh only 3.5 oz. Available in a 12/13 combo unit and a 22, 24, 27 and 32mm hex ends.