In 2008 Yamaha discontinued the XT225 & re-introduced the XT250. Powering the XT250 is a 249cc, air cooled, SOHC, single cylinder engine. Helping drive the XT250 is a five speed transmission & wet multi-disk clutch. In 2013 the US version XT250 gained fuel injection.
| Chain Size: | Front Sprocket: | Rear Sprocket: | Front Tire: | Rear Tire: | Spark Plug: |
| 428 x 128 | 15T | 48T | 2.75-21 | 120/80-18 | DR7EA |
For riders looking for advanced performance. Kit comes with everything you need to turn your XT250 into a rocket.
As with any engine or exhaust modification, you will need to re-tune your fuel delivery system for optimum performance.
Raises compression from stock 9.5:1 to 10.5:1 for more power and snappier response. Highest quality Wiseco pistons are forged in the USA. Fits the standard size stock bore.
As with any engine or exhaust modification, you will need to re-tune your fuel delivery system for optimum performance.
The EBC DRC kit is the best way to reset your bike’s clutch to the exact as new standard sizing. Replacing just the plates can work but new clutch springs are always better and springs get tired and can cause slippage plus the separator steel plates from EBC are pin-planished, forming tiny indents in the steel which improves the spread of oil around the clutch surfaces.
Includes:
Genuine Yamaha replacement gaskets for your side covers.
Complete set of engine gaskets with oil seals.
Complete top end gasket kit for the mighty XT250
Here are the O-Rings you need when you perform an oil change. These go inside the oil filter housing cover.
Replacing these O-Rings regularly will help keep your engine from seeping oil.
OEM valve cover o-rings
This is all you need to not only change your oil, but protect your motor as well. We include a magnetic drain plug, to help catch stray metal pieces, a 5-pack of oil filters, and new O-Rings to replace any you have that may be leaking or worn.
Made from laser cut, medical grade, 304 stainless steel micronic filter cloth. This filter provides 200% more filter area than most other filters. Most high quality filters will pass particles in the 90 to 95 micron range, and some tested, as much as 300 microns. Sand is about 125 microns and a white blood cell approximately 25 microns. Scott's stainless filter catches items down to 35 microns "absolute". The pleat seam is welded, not glued like paper filters, increasing temperature resistance to 600 degrees F.
Providing unbeatable performance and exceptional value, Hiflofiltro is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide. The filters are also supplied to original equipment manufacturers as well as private label brands.
Extra protection for your motor! Strong magnet at the end of the plug picks up metallic flakes in your oil, protecting your engine!
GoldPlug is the gold standard in engine protection.
Stainless steel drain plug with an extremely strong magnet that picks up metal flakes in your oil.
12mm Thread, 17mm Head.
A 10-pack of drain plug sealing crush washers. Replace your sealing washer at every oil change to prevent a leak.
Hardened chrome vanadium steel with built in rubber insert to hold spark plug steady.
Thin wall bi-hex sockets designed to access narrow spark plug holes.
Fits 3/8" square drive and hex drive, 14mm, 16mm, 18mm, 21mm.
E3 Resistor Spark Plugs
Keep your motor running right with fresh spark plugs!
NGK is one of the world's largest manufacturer of spark plugs, whose products are used as original equipment (OE) on countless motorcycle and automobile models.
Iridium spark plugs are made with premium quality materials.
Iridium plugs last longer than standard ones, meaning you won't have to replace them as often.
Sold individually, unless otherwise stated.
Genuine factory shop service and repair manual. This is the reference manual Yamaha dealers use in their service departments. It has all the necessary info to do any maintenance or repairs to your XT250.
Convenient tool to hold the clutch basket when servicing your clutch
Made from medium carbon steel with hardened jaws. It features spanner pins and the jaws open up to 5" wide. It's ideal for holding clutch hubs, flywheels, gears, sprockets, etc. Made by Motion Pro.
This tool is designed to separate vertically split crank case halves on two and four stroke engines. Adjustable arms allow it to be used on multiple bolt patterns found on a variety of makes and models of motorcycles. Industrial grade steel construction with black oxide finish for long service life. Comes with 8mm mounting bolts and 6mm adapters. Protective carrying case included.
For easy removal of recessed oil filters.
Conical point screws pierces and grabs the metal end cap of the filter.
reduces potential damage to the engine cases.
NOT for use on re-usable oil filters.
A 3-pack of easy to apply strips measure the temperature of engine, suspension, and radiator components. Temperature range 149° to 248°
Thread Chasers are designed to clean and re-cut damaged aluminum threads.
This kit contains the two sizes most common on metric motorcycles, M6x1.0 and M8x1.25.
Thread Chasers also remove dirt and metal shavings that become captured in thread grooves.
Uses 8mm or 10mm hex sockets, a Must for all tool kits.
Kit includes feeler gauges and wrench.
A 'wrench style' tool to turn the 'square top' tappet screws. The wrench does a better job of holding the adjuster screw still while tightening the locknut. Slim and flat, this tool is easy to carry in a tool pack.
Set includes:
