Our offices will be closed on Tuesday, December 24 and Wednesday, December 25 for Christmas. We will be back on Thursday, December 26. Happy Holidays!
Supermoto version of the DRZ400S
Street legal. Electric start. Wide 17" wheels.
Sold in the US 2000-current
| Chain Size: | Front Sprocket: | Rear Sprocket: | Front Tire: | Rear Tire: | Spark Plug: |
| 520x110 | 15T | 41T | 120/70-17 | 140/70-17 | CR8E |
All in one package.
We suggest adding a set of HotCams camshafts and a new clutch kit for the best results.
Cylinder Works Standard Bore High Compression Cylinder Kit
Stock bore replacement pistons from Wiseco. You have your choice of the standard compression ratio of 12.2:1, or a high-compression ratio of 13.5:1.
This high-compression kit will run perfectly with standard pump Premium.
Kits include piston, rings, wrist pin and circlips.
Solid reliability and easy installation. This manual tensioner is a good upgrade for any modified motor, especially if it is ridden hard.
A new gasket is included.
A Suzuki OEM gasket for the Cam Chain Tensioner. You are going to need it if you work on your starter motor. It is not a good idea to re-use this gasket. If it blows out, it will dump a large amount of oil onto your right foot.
Your automatic cam chain tensioner is spring loaded. This can make it difficult to install as it wants to extend before you have it bolted into place. This handy tool will back off the cam chain tensioner mechanism and hold it for you. No more awkward 3-handed contortions are required to get the tensioner installed.
A high quality cam chain from the folks at Wiseco. New cams, big bore kit, high-mileage motor, you might want to think about a new cam chain. Direct replacement for stock unit.
As the leader in innovation, design and development of aftermarket high-performance camshafts, Hot Cams is certain to provide the added boost that enthusiasts are looking for.
Designed, dyno proven and made in the USA, Hot Cams performance camshafts are one of the most economical, reliable and easy to install ways to add a 5-10% power gain to your bike.
Stage 1: These cams provide better low RPM torque, pulling power, and throttle response.
Stage 2: These cams will provide improved full throttle torque and horsepower starting at 4000 RPM and up.
Tech Notes: This cam replaces the 2047-1IN. It has better low RPM torque, pulling power, and throttle response. For best results it should be used with the #2050-1E exhaust cam. Uses stock DRZ400 valve springs.
This will not fit the DRZ400 kick start models. Nothing is available for the kick start models.
New Bearings for your DRZ400.
If you are in the lower end doing work, new bearings are cheap insurance for all that hard work.
Add a backup kick start system to your electric start DRZ400. Complete with everything you need to add the kick starter to your bike.
This kit will fit all DRZ400s but the manual decompression lever can only be installed on the 2006 to Current DRZ400 E models.
Includes three 9.48mm o.d. shims in each size from 1.20mm to 3.50mm in .05mm increments
Higher pressure in the cooling system, raises the coolant boiling point and increases protection from coolant loss due to overheating.
23 PSI - 1.6 Bar.
Replace your worn clutch plates and springs to reduce fade and slip.
Outer Clutch Cover O-Ring, Inner Clutch Cover Gasket, Stator Cover Gasket.
Sold individually, not as a kit
A complete set of gaskets, o-rings and oil seals. Everything you will need when doing a complete engine re-assembly.
Billet plugs for your left side case. Includes both the timing mark plug and the crankshaft access plug.
Always a good idea to put in a new set of Oil Change O-Rings at the first sign of any leakage. This package gives you the three most important: oil filter cap and the one behind the filter as well as the one on the filler cap. All are new OEM Suzuki O-Rings.
Made from laser-cut, medical-grade, 304 stainless steel micronic filter cloth, this filter provides 200% more filter area over many paper filters, catching debris down to 35 microns. The FLO filter pleat seam is welded and able to withstand up to 600 deg. F. Filter maintains consistent flow under all conditions including extreme heat, the presence of water and cold start-ups where paper filters can flow so poorly that they often cause the bypass valve to open and allow unfiltered oil to enter your engine.
This cleanable oil filter should be the last one you ever purchase.
Providing unbeatable performance and exceptional value, Hiflofiltro is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide. The filters are also supplied to original equipment manufacturers as well as private label brands.
Grab our 5-pack and save both time and money!
Extra protection for your motor! Strong magnet at the end of the plug picks up ferrous metallic flakes in your oil, protecting your engine!
GoldPlug is the gold standard in engine protection.
Stainless steel drain plug with an extremely strong magnet that picks up metal flakes in your oil.
12mm Thread
It is a good practice to replace your sealing washer with every oil change. These 10 piece kits are made up of 5 Copper washers and 5 Aluminum washers. The manufacturer recently decided to make half of the kit Copper washers as that is the material of choice for many OEM manufactures. This gives you the opportunity to decide which you prefer, but either will work great at creating a leak-free seal between the case and the drain plug.
A 10-pack of drain plug sealing crush washers. Replace your sealing washer at every oil change to prevent a leak.
Keep your motor running right with a fresh plug.
A Dual Electrode spark plug will last longer than a single electrode plug because the wear is shared between the electrodes.
Hardened chrome vanadium steel with built in rubber insert to hold spark plug steady.
Thin wall bi-hex sockets designed to access narrow spark plug holes.
Fits 3/8" square drive and hex drive, 14mm, 16mm, 18mm, 21mm.
E3 Resistor Spark Plugs
Keep your motor running right with fresh spark plugs!
NGK is one of the world's largest manufacturer of spark plugs, whose products are used as original equipment (OE) on countless motorcycle and automobile models.
Iridium spark plugs are made with premium quality materials.
Iridium plugs last longer than standard ones, meaning you won't have to replace them as often.
Sold individually, unless otherwise stated.
Clymer repair manuals provides step-by-step procedures based upon the complete disassembly of the motorcycle. This hands-on experience combined with extensive research results in a manual that is both user-friendly and detailed. Hundreds of original photos and illustrations guide the reader through every job.
Need to remove your clutch assembly? This holder is the quickest and easiest tool out there to get a grip on that hard to handle hub. Laser cut to the exact pattern that EBC makes their clutch plates from, it makes loosening and re-tightening the clutch nut easy. All of that and no worries about doing any damage to your expensive clutch hub.
Made from medium carbon steel with hardened jaws. It features spanner pins and the jaws open up to 5" wide. It's ideal for holding clutch hubs, flywheels, gears, sprockets, etc. Made by Motion Pro.
This tool is designed to separate vertically split crank case halves on two and four stroke engines. Adjustable arms allow it to be used on multiple bolt patterns found on a variety of makes and models of motorcycles. Industrial grade steel construction with black oxide finish for long service life. Comes with 8mm mounting bolts and 6mm adapters. Protective carrying case included.
For easy removal of recessed oil filters.
Conical point screws pierces and grabs the metal end cap of the filter.
reduces potential damage to the engine cases.
NOT for use on re-usable oil filters.
A 3-pack of easy to apply strips measure the temperature of engine, suspension, and radiator components. Temperature range 149° to 248°
Thread Chasers are designed to clean and re-cut damaged aluminum threads.
This kit contains the two sizes most common on metric motorcycles, M6x1.0 and M8x1.25.
Thread Chasers also remove dirt and metal shavings that become captured in thread grooves.
Uses 8mm or 10mm hex sockets, a Must for all tool kits.
