DRZ400S

We offer two different types of SuperMoto tubes. The first are Standard Tubes and are meant to be used with standard bias-ply type tires, but can be used with radial tires also.

But, if you are running radial tires, like SuperMoto, or have a retro bikes with spoked wheels and radial tires, you probably want to run the 'Radial Tubes'. Front tubes fits 120/70 and 120/60 tires. Rear tubes fits 150/60, 150/70 and 160/60 tires. These have a metal valve stem.

These Rider's Wrenches by Fredette are combination wrenches that have three wrenches in one! A 2-stroke size spark plug wrench - a front axle and a rear axle wrench. Yep, all three in one unit.

Available in the combinations shown that will fit virtually all current dual-sport machines.

A kit that includes an Axle Wrench combo for your bike with a 19mm for the front, and a 24mm for the rear. Just 7 1/2" long, it is long on leverage, but short enough to fit in even the smallest tool kit.

Also includes a pair of 'trail size' small tire irons.

This is a DRC wrench for your axle nut on one side, and a great tire spoon on the other.The long handle makes it easy to undo tight axle nuts and give you a bunch of leverage for changing tires. These are heat treated steel and range from 10 to 10.6 inches long.

Here is a set of 'trail size' tire irons. At 8-1/2 inches long they are small enough to fit in a fender bag with your spare tube.

Motion Pro T-6 Combo Lever has a hex box wrench for your axle nut on one side and a perfectly contoured tire spoon on the other. Manaufactured from lightweight forged T-6 aluminum with a hard anodized finish. These beauties are just under 10 inches long and weigh only 3.5 oz. Available in a 12/13 combo unit and a 22, 24, 27 and 32mm hex ends.

Our portable 12v compressor is perfect for any tool kit. This unit weighs only 14 oz and measures just 4"x2"x6".

Features a built in LED light and 0-120 psi gauge

• Comes with everything shown

The MotoPressor MICROPUMP™ is just that, micro.  It’s tiny, yet it will inflate a couple of rear tires and a front from flat, on a single charge. 

Recharge times run between 1-3 hours depending on the state of discharge of the battery.  

The MICROPUMP™ is equipped with an in-built tire gauge that reads pressures in PSI, BAR, KPA and Kg/cm2.  

It will pump up to 130PSI and you can SET and STORE 3 separate pressures in memory.  

It weighs just 323g and measures 78x72x35mm, easily fitting into any bag or pocket.  It’s even compact enough to fit into a tool roll.  

The pump is equipped with all the necessary accessories including a storage bag, air hose, charging cable and a Schrader adapter, ensuring you have everything to keep you rolling. 

Ultra compact, this Lithium battery powered tire inflator is ideal for inflating motorcycle and bicycle tires. 

• Pumps over 100 psi.
• Will inflate a 150/70 R18 rear tire from 0-36 psi TWICE and a 90/90 R21 front tire from 0-27 psi ONCE on a single charge.
• Set and store 3 separate pressures. 
• Pump will switch off automatically when the pre-set pressure is reached.
• Recharge from a 2 Amp USB outlet (charger not supplied).
• Charge time 1-3 hours.

Comes with:
Full set of operating instructions, NO AIR LOSS inflation hose, Schrader valve adapter, USB C charging cable, drawstring storage bag.  

The MotoPressor is a compact pump unit that weighs only 1.3 pounds and fits in the palm of your hand! Measures 4"x3"x1.5"  This makes it smaller and easier to carry with you.

It includes a 8 inch long inflation hose, with a a low air loss chuck. You also get an SAE power cord that attaches to your battery and stays there, along with alligator clips with SAE connector. The Pocket Pump has an 6.5 foot power cord. All of this packs into a heavy duty neoprene pouch.

MotoPressor will inflate a 150/70/ R18 tire from 0-31psi in under 4 minutes, and is capable of pumping up to 130psi. It also features a built-in cooling fan to keep the pump at optimum operating temperature, and a check valve to check the psi by attaching your tire gauge to this valve.

The Mini-Morph is actually a bicycle pump, but it is the best manual compact pump for adventure / dual-sport riding. It has a fold-out foot and handle and a 4 inch hose so you can set it on the ground to pump!

This thing is small enough to stow away in just about any bag and go unnoticed until you need it to fix a flat or add air after a long arduous ride.

All that you need to repair and inflate your tire on the road or trail.

• Padded nylon zippered carrying case easily stores inside fanny pack or tool compartment
• Everything needed to repair and inflate tire on the road or trail
• 4" inflator hose accepts threaded cartridges only
• Each cartridge produces 8-9 psi
• Made in the USA

Kit includes:

• 1 - large oblong patch
• 2 - medium size patches
• 3 - small patches
• Thumb buffer
• 0.50 oz tube of rubber cement
• 5 - 4" rubber insert strips
• Insertion tool with screwdriver handle
• Reamer/rasp tool with screwdriver handle
• 3 - 16 gram 3/8" threaded CO² cartridges
• CO² 4" inflator hose

CO² cartridges cannot be transported on an aircraft.

Don't leave yourself stranded! The Moose Tire Inflator Kit gets you back on the road or trail quickly.

This kit has 3 cartridges, 4" inflator hose, and a zippered pouch that fits neatly into a tool bag or fender bag.

Uses threaded cartridges only, each cartridge produces 8-9 psi.

  CO² cartridges cannot be transported on an aircraft

A set of 6 threaded cartridges, good for 8-9 psi each.

• Replacement packs for all CO² tire inflators
• Threaded cartridges have 3/8" threading

  CO² cartridges cannot be transported on an aircraft

The Pro Fill Air Chuck from the people at Motion Pro is perfect for those tough to reach valve stems with its pivoting angled head. The design gives users extra hand clearance to avoid hot brake rotors or dirty chains. Billet manufactured from aluminum gives it a precise fit and function combined with light weight. It is finished off with a beautiful blue anodizing and then the Motion Pro logo is laser etched on forever. 1/4" NPT female inlet allows use with common air hose couplings and fittings.

A great addition to any tool box!

MotoPressor Tire Gauge comes with two chucks. A straight chuck for "easy to get at" valve stems PLUS a 45° chuck for those "not so easy to get at" valve stems. 

We all know what a pain fuel Station gauges are. Most are woefully inaccurate and impossible to get onto a motorcycle valve stem. Enter the MotoPressor Tire Gauge…simply attach the MotoPressor Tire Gauge to your valve stem, attach the fuel station chuck to the inline fitting on the gauge and get an instant and accurate reading in PSI or KPA. 

No need to switch between the gauge and air compressor hose! Added a little too much air to your tire? Simply press the air bleed button and adjust to your desired pressure. 

NOTE: When swapping out the chuck, use plumbers tape on the hose thread. Wrap the thread, in a clockwise direction with 3 - 5 wraps of plumbers tape. Screw on the new chuck and tighten. Failure to follow these instructions will result in air leak! 

MotoPressor Tire Gauge comes with a one year limited product warranty. 

Specifications: 

• Measures PSI or KPA 
• 0-60 PSI/0-4.2 KPA read out 
• 50mm (2”) analogue dial 
• 300mm (12”) Braided flex hose 
• Push button air bleed valve 
• Protective rubber gauge guard 
• Self-locking air chuck PLUS A SECOND 45° chuck for those hard to get to, valves 
• Can be used in-line with a compressor

Changing tubes or tires without the right tools can be a real chore. Don't fight your snug beads any longer, use this 27" long tool that opens to 7-3/4" to provide the leverage you need to easily break your tire bead. Constructed from heavy-duty steel with comfortable no-slip grips, this tool makes the job a snap.

• A tool to keep open up the bead when replacing a tube.
• Works smoothly even with the toughest beads.

The Moose Tire Bead Tool holds your tire in place as you work you way around the tire

Made of aluminum with a nylon screw so it will not scratch the rim

Sold in pairs

• Durable 6061 aluminum with blue anodized finish and laser engraved logo
• Used to push the tire bead down into the drop center of the rim on off-road wheels while using tire tools to change tires
• Hooks over spoke and pushes bead down on opposite side of tire from tire irons
• No more fighting to keep bead down while installing off-road tires

No more fighting to keep the bead down while installing or repairing your off-road tires. The Bead Buddy holds the tire bead down in the drop center of the rim during tire changes making changes as easy as possible. Machined from tough 6000 series aluminum the Bead Buddy is light weight and compact enough for any tool pack. The Delrin securing thumb screw insures no scratches to your rims.

The Bead Buddy is NOT recommended for use with Bib Mousse tubes.

• Innovative multi-use tire tool set
• Breaks the bead on most street and off road motorcycle tires
• Integrated tire spoon for tire removal and installation
• Light weight and compact size is perfect for tool packs
• Ergonomic handles with crossguard to keep hand from riding forward
• Forged 7075-T6 aluminum construction for strength and durability
• Black anodized finish
• Patent pending

Available in 9.5" aluminum (ideal for travel) and 16" forged steel (useful in a home shop/garage)

Super sticky, pre-glued patches that adhere to tubes instantly.

This kit includes 6 patches and scuffer.

The MotoPressor Puncture Repair Tool combines the four tools essential for tubeless tire repair into a single tool.

With the motorcyclist in mind, they've designed a "4 in 1 multi-tool" that uses pre-vulcanized repair strings and packs into a sheath measuring a mere 130 x 68 x 50mm, that's small enough to fit in your pocket. The tool contains a pair of pliers, a rasp, an insertion tool and a sharp knife, which is all you'll need to fix 99% of punctures. The repair strings are pre-vulcanized, so they've done away with the "little tube of glue". The repair plugs the hole AND leaves a "patch style" repair on the INSIDE of your tire.

If you'd like to see the tool in action go just click HERE, and watch the demo.

Protect your wheels from scratches and dings caused by tire changing tools.

• Includes retrieval cord for easy use
• Sold in pairs

• Large display, readings are shown to 0.1 psi
• Kpa and Kg-cm2 scales also provided
• Reads up to 99 psi
• Ergonomic shape fits nicely in your hand

This "pencil style" tire gauge has a brass head and a plated brass body.

90° angle allows for easy access to valve stems and easy reading.

5 to 50 psi measurement in one pound increments.

Very accurate.

This great tire gauge measures from 0-100 psi.

Has a back-lit display, and a front light to help locate the tire valve.

Select from psi to kPa units of measurements.

Replaceable batteries and automatic shutoff

CE approved and CARB compliant.

Very accurate.

Refresh your front or rear tire instead of throwing them out! Tread Doctor Lightweight heated tool lets you quickly cut new edges into your dull worn out knobby tires.

Features:

• Aluminum air valve cap
• Comes in pairs
• Add some " bling " to your bike
• Helps Keep the air in your tire

The aluminum part can be used as a valve core remover / wrench.
- Made of A6061 aluminum.
- Available in 6 beautiful anodized colors.
- Comes in pairs.

Warp 9 stem puller

 Here is a list of the features of their CNC machined tool.

• Stainless Steel tip, wont break like softer brass tip
• Ribbed head for easier core removal
• Core tip threads into handle to protect tip from damage
• Includes spare valve core in handle for easy trail side repairs
• Tapered handle ends to make tip removal easier with gloved hands and non square edge doesn’t damage tool bags

In the shop or on a trip, these are the Tire Irons to have.

Sold Each

• Constructed of strong, heat-treated vanadium steel
• Spoon design decreases the chance of tube pinch
• 10" long tire iron with coated rubber handle

Windscreen attaches to your bike's handlebars. Fully adjustable mounting brackets. Includes 7/8' handlebar clamps. 14" tall & 10" wide.

Will not fit 1 1/8" oversize handlebars.

Molded using a very durable, lightweight 1/8" thick polycarbonate - giving the windshield a high impact strength and making it shatter-resistant with a superior light transmission quality. Mounts quickly and easily onto the stock headlight cowling for a clean factory look. Drilling of the cowling is required, hardware is included. Removal for trail riding is also quick and easy.

Transform your ride
Now there is wind protection for on and off-road use with no compromises! MadStad's new rotating dual-sport windshield brackets put the windshield where you need it for street riding, but tuck it down out of the way for off-road. Adjust the height and angle for much smoother airflow, better wind protection and a more comfortable ride than any fixed windshield can provide, and it's not in your face when you want to hit the trails.

Their complete drop-in system is custom-made for your bike and includes everything needed to mount and position the shield. Your bike will not require any modification.

What's included in the kit

• A set of MadStad dual-sport adjustable brackets
• The acrylic windshield

The MadStad brackets bolt to your fork clamps putting the windshield just in front of your instrument cluster for street riding, with adjustability for height and angle. The rotation feature allows you to shift the shield forward and down through 7 different settings bringing it down in front of the head light and out of your way. Their custom knobs lock the brackets in their multiple positions so the shield stays where you want it to, even bouncing around off-road.

The Rally windscreen from Parabellum is the perfect protection from wind and debris without sacrificing technical off-road capabilities. This is an upright rally type windscreen that looks aggressive and performs well under all types of riding. Designed primarily for the off-road / dualsport enthusiast, this shield keeps pressure off the rider's chest while commuting from home to adventure and back.

Mounting is accomplished by drilling two holes on each side of your headlight cowl using the provided template. The shield is 14 inches tall, 11.5 inches wide at the bottom narrowing to 8.5 inches at the top. Made from military aircraft grade cast acrylic.

This unit will not fit properly on '90 to '01 DR650 headlight cowls.

Puig Visor Clip-On

• Suitable for screens with thickness between 3-5mm
• Multi-adjustable visor adaptable to Puig and OEM windscreens
• Visor is mounted by clip-ons and does not need to be drilled to the windscreen
• Visor sizes available include 90x230mm, 100x277mm and 102x325mm

High-quality, direct replacement plastic kit includes:

• Front and rear fender
• Side covers
• Air box cover
• Radiator shrouds

Yellow kit is only available with white side covers

  Add-on Headlight cowling fits S and SM models not "E" offroad model

Universal design. Vents in the back improve airflow to motor. Smaller front reduces 'wind steer' and improves high speed stability.

Genuine Suzuki super moto fender. A perfect match for the original gray plastic.

Universal off-road front fender. Must be drilled to fit your mounting bolt pattern.

Front fender from ProCycle Plastics (formerly DSA) is shaped very much like the OEM DRZ400SM front fender. Big enough to be functional without wind-steering the bike like the stock fender does. Vacuum molded, these are a design improvement over stock. These are fully compatible in any combination with the original factory plastic.

OEM Suzuki headlight cowling.

Quality parts from Acerbis. Replace those big white ones with black ones for a custom look, or you can just replace your trashed white ones with crisp clean new ones for that great stock look.

Depending on your application and preferences, more than one optional heat shield may be useful.

This frame includes six, white, full-spectrum LED bulbs on a 6-inch strip for bright illumination of your license plate. It is made in a sturdy cast aluminum, and is powder coated with a durable black finish.

Outside frame dimensions are 7.25" in. wide by 4.2". Center to center mounting hole distance is 5.7 in. All mounting hardware is included.

• Stealth license plate vanity light.
• Built-in turn signals.
• Running and Brake Lights.
• 218 LEDs ultra bright.
• 18 white leds. 1.5W max output.
• 200 red leds. 6W max output.
• 12v DC input.

• Waterproof, long-lasting marker light bar uses less power
• Features 180° visibility
• White LED color
• Can be used in any position; refraction of light depends on position
• Measures 38mm x 9.8mm x 18mm
• Not for use where DOT lighting is required.

License plate light with 5 LEDs. Compact and easy to mount. Meets plate illumination requirements with super white light.

This is for the LED license plate light ONLY.

License plate bolt with bright white LED light. The simple way to light up your plate.

B&B Off Road Engineering Fender Brace is made to help support your front fender/guard. Also helps support and reduce fatigue from constant vibration.

Made from 4mm 5083 structural aluminum plate. If you wanted to carry a small tool bag this would be a perfect product to support the weight and strap the bag to.

Fits on top of the fender and bolts between the fender and bottom triple clamp. Requires you to drill one hole in the fender for mounting.

A stainless steel front fender brace. Helps stabilize your front fender.

Gives additional strength for carrying a fender mounted tool bag.

Fits on top of the fender and bolts between the fender and bottom triple clamp. Stainless steel won't rust or corrode. Includes hardware.

Requires you to drill one hole in the fender for mounting.

Adhesive heat shield for your new side panel plastics to protect it from the heat of your muffler.

Depending on your application and preferences, more than one heat shield may be useful.

Dimensions: 2"x3'

Moose Racing Adventure seat provides improved comfort for your riding adventures, or just commuting around. You choose between the stock seat height, or a low seat height (about 1 inch lower). The durable micro-fiber suede top cover enhances rider comfort and increases stability. Side gripper panels ensure secure seating during aggressive maneuvers. The cover is constructed from smooth marine-grade vinyl and features an embossed Moose Racing logo. It includes a strap kit that enables secure attachment of cargo to the pillion section of the seat.

Corbin seats are carefully designed to provide a comfortable riding position. They are firm and supportive which allows you to ride all day without fatigue unlike the stock seat. Comfort Cell Foam retains resilience and doesn't crush down like the stock seat foam. On the top, Corbin covers are only the highest grade of weather resistant materials for durability and long life. Corbin seats install the same as similar to stock with two bolts into the chassis which provides a closer fit to the bodywork and tank.

Seat Concepts new wider seat to helps keep you comfortable on those long commutes or Dual-Sport rides. The added width and foam density will help keep the seat from being the item to stop you from going on that ride or enjoying the bike.

The new updated 2.0 version has a sleeker shape and a better fit in the tank area.

Complete Seats come assembled on an high quality aftermarket pan and ready to ride.

New wider seat to help keep comfortable on that long commute or dual sport ride. The added width and foam density will help keep the seat from being an item to stop you from going on that ride or enjoying the bike.

The new updated 2.0 version has a sleeker shape and a better fit in the tank area.

Complete Seats come assembled on an aftermarket pan and ready to ride.

This Comfort XL seat design is roughly 3" wider overall than their standard comfort seat. This means more surface area, better weight distribution, and added comfort for those not worried about seat width.

Available as Complete Seat only. The Complete Seats come assembled with an aftermarket pan and ready to ride.

State-of-the-art replacement seats, Sargent seats are built on a percision-molded lightweight Polytec seat pan. Sargent's proprietary seat foam (Super Cell Atomic Foam) is their own unique blend of resilience, firmness, and vibration-absorption qualities, making it well suited for long distance comfort and support. Sargent seats are covered in a marine-grade, UV-stablized mildew resistant CarbonFX vinyl. These seats will fit bikes with the stock, IMS, or any other aftermarket fuel tank.

This is a high-quality seat cover done by Moose for the DRZ400. This is a replacement cover only, no seat foam and you must install on your existing pan with existing foam. Heavy-duty marine grade vinyl with UV protection for long life. Double stitched for durability too!

Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!

This is the secret for being able to put in those 500 mile days. Even a good touring seat can feel a bit harsh after a couple hundred miles. These very comfortable sheepskin seat covers give you that extra bit of 'cush' and provides superior air circulation. Velcro straps allow easy install and removal when you don't need it. Measures 14" wide by 19" long, the perfect size for Dual-Sport seats.

Air filled AirHawk 12"x18" cushion custom fits your shape and redistributes pressure that causes numbness and discomfort when you ride. Seat cushion cover is constructed of a breathable, stretchable Nylon/Lycra blend with a non skid Urethane base. Open mesh side panels allow heat to escape. Easily inflates by mouth with no pump needed. Mounting straps and Repair patch kit included.

9" by 9" carbon fiber seat warmer that goes between your seat cover and the foam to keep your backside happy on those really cold days. This improved design produces 25% more heat than most other warmers using just 30 watts.

Kit includes the warming unit, with connector, 24" extension cable, rocker-type on/off switch and stub to splice into your wiring along with complete detailed instructions.

Yes, plastic! This is a product from our friends at Acerbis. Ultra tough injection molded reinforced composite. Flexible Heavy-Duty Polypropylene will not effect chassis ability to flex, will not effect handling

It's twice as thick as a metal skid plate but is only half the weight. Plastic glides over rocks and roots better than aluminum. It also reflects less engine noise, bike will run quieter and cooler compared to alloy skid plate. Full coverage, mounts to existing threaded holes at the rear of the frame.

Replace the wimpy stock DRZ400 Skid Plate made from 4mm thick 5083 aluminium plate. Strong and great looking. Leave the stock wings in place and give yourself something that will really stop any damage between the frame rails. Supplied with all the necessary stainless steel clamps and bolts required. Available in polished or with the heavy-duty black polymer coating. Like all he other B&B Bash Plates, these plates have foam or rubber where required to keep things a bit more quiet. This plate fits the E, S, SM & kick start models.

The B & B Eng. DRZ400 Bash Plate is made from 4mm thick 5083 aluminium plate. Strong and great looking, this is the top of the line protection plate for the DRZ. Supplied with all the necessary stainless steel clamps and bolts required. Available in polished or with the heavy-duty black polymer coating. Like all he other B&B Bash Plates, these plates have foam or rubber where required to keep things a bit more quiet. This plate fits the E, S, SM & kick start models.

Thick carbon fiber plate with many advantages over aluminum.

The use of anti-ballistic composite material provides a longer fatigue life and greater tensile strength than aluminum.

Composite plates are molded to the exact shape desired, making for a closer fit and a more protective plate.

Composite plates absorb vibration and do not amplify sounds like aluminum plates do.

When hit hard, aluminum permanently deforms, bending frame tubes and slicing into water pumps.

Composite plates will bounce back from hard hits and look great long after aluminum plates give up.

Skid plates protect the side engine cases and the water pump in addition to the frame and the center case.

Designed with a high front to keep mud from building up on the engine.

Mounting hardware included.

• Made from strong and lightweight aircraft aluminum
• Protects vital engine parts from rocks and debris
• Custom fit to your specific bike model
• Oil drain hole for easy access
• All mounting hardware included

Clutch and Ignition covers made by B&B Eng. Formed from 2mm thick 5052 aluminum plate, selected because of its strength, corrosion resistance, excellent abrasion and impact protection. These will help protect your cases in the event of a bad fall.

These covers are attached to the engine cases with high quality heat resistance silicone adhesive

These covers will NOT fit early kick start only models that did not come standard with electric start. If you have added a kick starter to your bike that came with an electric start, covers will fit with no problem.

• Motor Crankcase and Ignition/Clutch covers that protect against wear from boots, impacts, dirt, mud, and other debris
• Right side: provides protection for the clutch cover, water pump, and lower casing
• Left side: provides protection to the ignition cover and clutch actuator
• Molded openings to access the filter cover and oil cap
• Easy to install by utilizing the original crankcase and ignition/clutch cover bolts
• Resistant to high temperatures
• Designed not to interfere with boots

The X-Grip is a frame guard that allows the rider to both protect the frame of the motorcycle from wear as well as adding more grip to the bike.

Made from a dual injected mold; The outer plastic is durable polycarbonate while the inner plastic is durable yet playable and offers incredible grip.

Available in 3 colors

Protect your frame/paint from scuffs and scratches with frame guards. The DRZ 400 frame guards are made from 2mm 5052 marine grade alloy and CNC machined in one piece for strength. All frame guards are supplied with all necessary mountings and stainless bolts. With a polished finish they look great and are easy to install.

Give your DRZ that factory prepped look and protect your frame.

These frame guards from industry leaders Works Connection are CNC cut and formed from aircraft grade 5052 aluminum. These not only protect your frame from scuff and rub marks from your boots, but also give you a flatter surface for better grip and control with your lower legs. All the necessary mounting hardware is included making these a very simple bolt-on installation.

High quality aluminum caliper guards from Works Connection protects your brake caliper and looks great too.

Protect your brake rotor and fork lowers from mud and debris. Choose between black or white.

Protect your brake discs with high-grade aluminum alloy disk guards by Devol.

• Covers entire front leading edge
• Light weight and very effective
• Easy to install; all hardware included

Radiator guards from Devol Racing protect your radiators from damage due to trail side objects and roost bullets. They offer protection not just from frontal assaults but also from those tricky side attacks. Made from high-grade aluminum alloy for light weight and strength, these guards have an improved air-flow design that eliminates any overheating problem. A solid mounting to the frame make these stronger than most guards that just mount to the radiators themselves.

Devol Racing makes a super product that will keep you on the trail for a long time.

This is the ultimate in radiator guards! It will protect your fragile radiator from nasty front & side impacts.

This ultra tough guard is constructed from 1/8" aluminum and is easy to install.

All Flatland Racing radiator guards have rear mounting brackets for that extra support! All Mounting hardware is included. 

Shield your bike’s vital drivetrain components with B&B Off Road’s heavy-duty front sprocket case saver. This premium guard, CNC-machined from high-strength 6mm aluminum plate, offers unparalleled protection against rocks, impacts, and other off-road hazards.

Uncompromising Strength, Precision Fit:
Engineered for maximum durability, this case saver boasts a 6mm main body crafted from 5083 structural aluminum – a material renowned for its resilience. Complementing this robust core is a 4mm thick front sprocket cover, ensuring comprehensive protection for your drivetrain.

Designed for Flawless Performance:
CNC machining guarantees a precise fit for both Suzuki DRZ400 (2000+) and Kawasaki KLX400 (2000+) models. This ensures seamless integration with your bike, eliminating concerns about interference or compatibility issues.

Peace of Mind on Every Ride:
Whether you’re navigating technical single tracks or powering through dusty plains, this case saver offers the confidence to push your limits. By safeguarding your front sprocket and surrounding components, it minimizes the risk of costly repairs and keeps you on the trail.

• Made from 5083 structural aluminum for durability
• 6mm thick main case saver body
• 4mm thick front sprocket cover
• All components CNC machined for a precision fit
• Fits 14 and 15 tooth sprocket

CNC machined from 2.5mm marine grade aluminum- replace the stock plastic guard

This heavy duty DRZ400 chain guard is made of laser cut 1/8” aluminum and finished in textured black powder coating.  The formed flange helps keep chain grime off the rear tire.  

Mounting hardware included. 

Made of military aircraft grade 3/16" cast acrylic, this guard will protect your lens from roost, rocks and branches. Optical clarity of the acrylic ensures brightness and projection of your headlight are minimally effected while all the while protecting your headlight from impact and abrasion.

Guards are held to the headlight lens with an industrial strength hook and loop system on each corner.

To fit straight 22mm (7/8″) handlebar.

• Barbusters strongest handguard EVER!
• Designed for Enduro and Trail bikes.
• Two mounting points secure the full wrap around aluminum design.
• Compact curved profile to protect hands and levers during intense trail and tight bush riding.
• Heat treated aluminum backbone for maximum strength.
• Replaceable, high impact resistant EGO plastic guards included.
• Large range of colors matched to popular motorcycle brands.
• Deflectors available for increased protection (sold separate).
• Easy installation.
• NOTE: Not ideal for bikes with long clutch and brake levers.

For straight 7/8" handlebar

Protect your hands and levers with the Barkbusters Storm lever and weather protection handguards. Full wrap solid heat treated aluminum bars with secure two point mounts on each side provide strength while attractive and generous guards provide shelter from the wind and weather. Ride longer with the Storm handguards and complete mounting kit by Barkbusters.

Features:

• Two mounting points provide secure protection
• Full wrap guards
• Heat treated aluminum backbone bars
• Easy installation
• Tough and weather shielding Storm handguards
• Aluminum backbones are compatible with all Barkbusters deflector guards

What's in the box:

• Left and right aluminum backbone bars
• Inner and outer handlebar mounting hardware for both sides
• Left and right Storm plastic handguard deflectors
• Installation instructions

Not recommended for Africa Twin, T7, Himalayan, or V-Strom. Please see specific listings for those models.

For Straight 7/8" handlebar

Keep your hands and controls protected from the wind and impact with Barkbusters VPS lever and wind protection handguards. Heat treated aluminum backbones with two mounting points of these handguards provide the strength needed to prevent a tip-over from ending your motorcycle ride. Impact resistant deflectors, available in multiple colors, provide protection for your hands from the wind and brush. Ride longer, more comfortably with Barkbusters VPS lever and wind protection handguards

Features:

• Two mounting points provide secure protection
• Full wrap guards
• Heat treated aluminum backbone bars
• Includes VPS left and right plastic deflectors
• Easy installation

What's in the box:

• Left and right aluminum backbone bars
• Inner and outer handlebar mounting hardware for both sides
• Left and right VPS plastic deflectors
• VPS deflector fastening hardware
• Left and right adjustable position wind extension deflectors
• Installation instructions

Not recommended for Africa Twin, T7, Himalayan, or V-Strom. Please see specific listings for those models.

For Straight 7/8" handlebar

Contoured alloy hand guards with inner mounts, allow space for the clutch cable and brake hose.

Note: This kit includes the handguards only. Deflectors sold separate, can be added by selecting color from drop down menu.

For DR650 or other models with long levers add the optional universal fit Spacer Kit so you don't have to cut the balls off the end of your levers when installing these handguards. (May require additional adjustment or modification on some models.) 

To fit tapered 28.5mm (1 1/8") handlebar.

• Barkbusters strongest handguard EVER!
• Designed for Enduro and Trail bikes.
• Two mounting points secure the full wrap around aluminum design.
• Compact curved profile to protect hands and levers during intense trail and tight bush riding.
• Heat treated aluminum backbone for maximum strength.
• Replaceable, high impact resistant EGO plastic guards included.
• Large range of colors matched to popular motorcycle brands.
• Deflectors available for increased protection (sold separate).
• Easy installation.
• Note: Not ideal for bikes with long clutch and brake levers.

NOTE: will not fit Renthal Twin Wall or Barkbusters VSBar.

For Tapered 1 1/8" Handlebar

Protect your hands and levers with the Barkbusters Storm lever and weather protection handguards. Full wrap solid heat treated aluminum bars with secure two point mounts on each side provide strength while attractive and generous guards provide shelter from the wind and weather. Ride longer with the Storm handguards and complete mounting kit by Barkbusters.

Features:

• Two mounting points provide secure protection
• Full wrap guards
• Heat treated aluminum backbone bars
• Easy installation
• Tough and weather shielding Storm handguards
• Aluminum backbones are compatible with all Barkbusters deflector guards

What's in the box:

• Left and right aluminum backbone bars
• Inner and outer handlebar mounting hardware for both sides
• Left and right Storm plastic handguard deflectors
• Installation instructions

Not recommended for Africa Twin, T7, Himalayan, or V-Strom. Please see specific listings for those models.

NOTE: tapered kit will not fit Renthal Twin Wall or Barkbusters VSBar

For Tapered 1 1/8" handlebar

Keep your hands and controls protected from the wind and impact with Barkbusters VPS lever and wind protection handguards. Heat treated aluminum backbones with two mounting points of these handguards provide the strength needed to prevent a tip-over from ending your motorcycle ride. Impact resistant deflectors, available in multiple colors, provide protection for your hands from the wind and brush. Ride longer, more comfortably with Barkbusters VPS lever and wind protection handguards

Features:

• Two mounting points provide secure protection
• Full wrap guards
• Heat treated aluminum backbone bars
• Includes VPS left and right plastic deflectors
• Easy installation

What's in the box:

• Left and right aluminum backbone bars
• Inner and outer handlebar mounting hardware for both sides
• Left and right VPS plastic deflectors
• VPS deflector fastening hardware
• Left and right adjustable position wind extension deflectors
• Installation instructions

Not recommended for Africa Twin, T7, Himalayan, or V-Strom. Please see specific listings for those models.

NOTE: tapered kit will not fit Renthal Twin Wall or Barkbusters VSBar

For Tapered 1 1/8" handlebar.

Contoured alloy hand guards with inner mounts, allow space for the clutch cable and brake hose.

Note: This kit includes the aluminum handguards only. Plastic deflectors sold separate, can be added by selecting color from drop down menu.

For DR650 or other models with long levers add the optional universal fit Spacer Kit so you don't have to cut the balls off the end of your levers when installing these handguards. (May require additional adjustment or modification on some models.) 

Closed handguard with aluminum bar and bracelets.

Ultra-durable closed handguard designed for those seeking greater protection while competing or riding in enduro, hard-enduro and cross-country racing.

Equipped with a 35 mm "C" section anticorodal bar. Provides 5 times more resistance than the classic handguard with an aluminum bar.

The cuffs, oversized with a thickness of 19 mm, guarantee greater strength and increased torsional capacity.

Expanders made entirely of steel.

Cover is impact resistant; wide area protects the pilot's hands more, while flexible lower area absorbs any accidental contact with the knee.

Mounting kit included.  Mounts to all off-road competition bikes (motocross and enduro) with inner size from 13.5-16 mm and outer size from 22-28 mm.  Works with 7/8" or 1-1/8" bars.

Co-molded logo.

The Rally Pro X-Strong features a high-impact, composite injection-molded outer guard surrounding an anodized aluminum inner guard. It is equipped with an indexed steel bar-end insert that ensures a secure installation, preventing Rally Pro handguards from slipping, even in challenging conditions. Additionally, a compact integral spoiler is incorporated into the design. The package includes a robust universal silver mount kit that is compatible with 7/8” (22mm), Pro Taper 1 1/8” (28mm), Magura, and Twin Wall aluminum handlebars.

Some models with adjustable windscreens may need the windscreen rotated forward, such as the Royal Enfield Himalayan, to avoid contact at full lock. These are not compatible on Honda CB500X's and Honda Africa Twins.

These handguards come with mounts that will work on both standard and and oversize bars. The aluminum wrap-around bar is the biggest on the market with two large plastic shields that are also some of the largest available. The X-Factor hand guards offer great protection from the elements, especially during those colder months when you're trying to stretch out your riding season.

Works with 7/8" or 1-1/8" bars.

X-Factor guards may require you to cut your lever ends down, or use short levers.

The X-Factory Handguards from Acerbis are designed with a steel bar encased in an injection-molded Nylon composite. A replaceable dual-injected polypropylene shield attaches to the bar, providing excellent protection against debris and harsh conditions.

Included with the handguards is a universal mount kit, enabling installation on either 7/8" or 1 1/8" handlebars.

Will not fit XT250 with stock handlebars (oversize bars ok). Recommend Acerbis Rally Pro X-Strong to clear master cylinder.

Construction of these handguards feature heavy duty aluminum guards with colored plastic deflector shields. They offer great protection from those trees that jump out at you on the trail and the cold wind and rain you encounter on the street. They feature a deep bend on the outer bar end for maximum freedom of hand placement and high quality bar mounts on the inside.

Select your desired color. 

Must add the corresponding size mounts to fit your handlebar.

For DR650 or other models with long levers add the optional universal fit Spacer Kit so you don't have to cut the balls off the end of your levers when installing these handguards. (May require additional adjustment or modification on some models.) 

Please Note: These handguards do not fit the Yamaha T7

FUZION guards feature the ultimate in hand protection with a unique design and flexible yet durable material. 

The expanded coverage area sweeps back toward your hand significantly increasing coverage making it perfect for cold, muddy or wet conditions. 

The FUZION features a unique two position mount and is constructed of molded light-weight closed-cell AEPE foam, which is crush-proof, water proof and extremely durable. 

The FUZION will work great for road of offroad riding, where wind deflection is important, and or bouncing off trees is a common occurrence. 

Kit includes mounts. Optional replacement mounts available.

• Designed to minimize handlebar vibration for Barkbuster Handguards that can’t accomodate OEM handlebar weights.
• Sleek aerodynamic look.
• Forged Steel with powder coat finish.
• Fit in conjunction with most Barkbusters backbones (except EGO).
• Fits externally to the VPS backbone.
• Available in black.
• Sold as a pair

Weight:
360 grams/pair or
180 grams/each

To be fitted to the top of the Barkbuster EGO handguard.

• Easy installation.
• Can be removed in minutes for a more compact feel.
• Deflectors provide maximum protection and coverage from the elements.
• Deflector Set available in black or white to suit your style.
• Includes two deflectors and mounting screws.

Fits Moose and other aluminum hand guards

• Aerodynamic and stylish design
• Protect hands from brush, water and cold wind
• Simple installation
• Sold in pairs

Don't cut the ball ends off of your levers! These billet spacers move your hand guards outward to allow clearance for the full length of the stock levers. Designed to fit steel or aluminum bars. Includes longer stainless steel mounting bolts.

Developed for the DR650 but may work on other models with long levers. (May require additional adjustment or modification on some models.) 

  Not compatible with Acerbis and Emgo hand guards

You can keep your Cycra handguards even if you upgrade your handlebars to a different width.  

Replacement mounts that keep your Cycra handguards fresh and tight.

CNC-machined from billet aluminum for the best fit and strength.

Please Note: These handguards do not fit the Yamaha T7